diff --git a/MAKEALL b/MAKEALL
index e807063..e382947 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -346,6 +346,7 @@
 
 LIST_85xx="		\
 	ATUM8548	\
+	MPC8536DS	\
 	MPC8540ADS	\
 	MPC8540EVAL	\
 	MPC8541CDS	\
@@ -354,6 +355,7 @@
 	MPC8555CDS	\
 	MPC8560ADS	\
 	MPC8568MDS	\
+	MPC8572DS	\
 	PM854		\
 	PM856		\
 	sbc8540		\
diff --git a/Makefile b/Makefile
index 89fea72..c43e2c3 100644
--- a/Makefile
+++ b/Makefile
@@ -2206,6 +2206,9 @@
 ATUM8548_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc85xx atum8548
 
+MPC8536DS_config:       unconfig
+	@$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8536ds freescale
+
 MPC8540ADS_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8540ads freescale
 
@@ -2265,6 +2268,9 @@
 MPC8568MDS_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8568mds freescale
 
+MPC8572DS_config:       unconfig
+	@$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8572ds freescale
+
 PM854_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc85xx pm854
 
diff --git a/board/atum8548/Makefile b/board/atum8548/Makefile
index d2e689f1..b991308 100644
--- a/board/atum8548/Makefile
+++ b/board/atum8548/Makefile
@@ -29,10 +29,13 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-$(CONFIG_FSL_DDR2) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/atum8548/atum8548.c b/board/atum8548/atum8548.c
index 34f4599..337cf31 100644
--- a/board/atum8548/atum8548.c
+++ b/board/atum8548/atum8548.c
@@ -29,7 +29,9 @@
 #include <asm/processor.h>
 #include <asm/immap_85xx.h>
 #include <asm/immap_fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <asm/io.h>
+#include <asm/mmu.h>
 #include <spd_sdram.h>
 #include <miiphy.h>
 #include <libfdt.h>
@@ -106,8 +108,10 @@
 	puts("Initializing\n");
 
 #if defined(CONFIG_SPD_EEPROM)
-	puts("spd_sdram\n");
-	dram_size = spd_sdram ();
+	puts("fsl_ddr_sdram\n");
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 #else
 	puts("fixed_sdram\n");
 	dram_size = fixed_sdram ();
diff --git a/board/atum8548/ddr.c b/board/atum8548/ddr.c
new file mode 100644
index 0000000..f07d746
--- /dev/null
+++ b/board/atum8548/ddr.c
@@ -0,0 +1,80 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+			unsigned int ctrl_num)
+{
+	unsigned int i;
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 7;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8536ds/Makefile b/board/freescale/mpc8536ds/Makefile
new file mode 100644
index 0000000..7fcbdaa
--- /dev/null
+++ b/board/freescale/mpc8536ds/Makefile
@@ -0,0 +1,54 @@
+#
+# Copyright 2008 Freescale Semiconductor.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mpc8536ds/config.mk b/board/freescale/mpc8536ds/config.mk
new file mode 100644
index 0000000..9775ff4
--- /dev/null
+++ b/board/freescale/mpc8536ds/config.mk
@@ -0,0 +1,32 @@
+#
+# Copyright 2008 Freescale Semiconductor.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8536ds board
+#
+ifndef TEXT_BASE
+TEXT_BASE = 0xeff80000
+endif
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8536=1
diff --git a/board/freescale/mpc8536ds/ddr.c b/board/freescale/mpc8536ds/ddr.c
new file mode 100644
index 0000000..2e88c79
--- /dev/null
+++ b/board/freescale/mpc8536ds/ddr.c
@@ -0,0 +1,79 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 7;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8536ds/law.c b/board/freescale/mpc8536ds/law.c
new file mode 100644
index 0000000..cdf5215
--- /dev/null
+++ b/board/freescale/mpc8536ds/law.c
@@ -0,0 +1,43 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CFG_PCI1_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCI),
+	SET_LAW(CFG_PCI1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI),
+	SET_LAW(CFG_FLASH_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+	SET_LAW(CFG_PCIE1_MEM_PHYS, LAWAR_SIZE_128M, LAW_TRGT_IF_PCIE_1),
+	SET_LAW(CFG_PCIE1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_1),
+	SET_LAW(CFG_PCIE2_MEM_PHYS, LAWAR_SIZE_128M, LAW_TRGT_IF_PCIE_2),
+	SET_LAW(CFG_PCIE2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_2),
+	SET_LAW(CFG_PCIE3_MEM_PHYS, LAWAR_SIZE_512M, LAW_TRGT_IF_PCIE_3),
+	SET_LAW(CFG_PCIE3_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_3),
+	SET_LAW(PIXIS_BASE, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/mpc8536ds/mpc8536ds.c b/board/freescale/mpc8536ds/mpc8536ds.c
new file mode 100644
index 0000000..8216c70
--- /dev/null
+++ b/board/freescale/mpc8536ds/mpc8536ds.c
@@ -0,0 +1,653 @@
+/*
+ * Copyright 2008 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/immap_fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/io.h>
+#include <spd.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <spd_sdram.h>
+#include <fdt_support.h>
+
+#include "../common/pixis.h"
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+phys_size_t fixed_sdram(void);
+
+int checkboard (void)
+{
+	printf ("Board: MPC8536DS, System ID: 0x%02x, "
+		"System Version: 0x%02x, FPGA Version: 0x%02x\n",
+		in8(PIXIS_BASE + PIXIS_ID), in8(PIXIS_BASE + PIXIS_VER),
+		in8(PIXIS_BASE + PIXIS_PVER));
+	return 0;
+}
+
+phys_size_t
+initdram(int board_type)
+{
+	phys_size_t dram_size = 0;
+
+	puts("Initializing....");
+
+#ifdef CONFIG_SPD_EEPROM
+	dram_size = fsl_ddr_sdram();
+
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+
+	dram_size *= 0x100000;
+#else
+	dram_size = fixed_sdram();
+#endif
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+	/*
+	 * Initialize and enable DDR ECC.
+	 */
+	ddr_enable_ecc(dram_size);
+#endif
+	puts("    DDR: ");
+	return dram_size;
+}
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+
+phys_size_t fixed_sdram (void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_ddr_t *ddr= &immap->im_ddr;
+	uint d_init;
+
+	ddr->cs0_bnds = CFG_DDR_CS0_BNDS;
+	ddr->cs0_config = CFG_DDR_CS0_CONFIG;
+
+	ddr->timing_cfg_3 = CFG_DDR_TIMING_3;
+	ddr->timing_cfg_0 = CFG_DDR_TIMING_0;
+	ddr->timing_cfg_1 = CFG_DDR_TIMING_1;
+	ddr->timing_cfg_2 = CFG_DDR_TIMING_2;
+	ddr->sdram_mode = CFG_DDR_MODE_1;
+	ddr->sdram_mode_2 = CFG_DDR_MODE_2;
+	ddr->sdram_interval = CFG_DDR_INTERVAL;
+	ddr->sdram_data_init = CFG_DDR_DATA_INIT;
+	ddr->sdram_clk_cntl = CFG_DDR_CLK_CTRL;
+	ddr->sdram_cfg_2 = CFG_DDR_CONTROL2;
+
+#if defined (CONFIG_DDR_ECC)
+	ddr->err_int_en = CFG_DDR_ERR_INT_EN;
+	ddr->err_disable = CFG_DDR_ERR_DIS;
+	ddr->err_sbe = CFG_DDR_SBE;
+#endif
+	asm("sync;isync");
+
+	udelay(500);
+
+	ddr->sdram_cfg = CFG_DDR_CONTROL;
+
+#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+	d_init = 1;
+	debug("DDR - 1st controller: memory initializing\n");
+	/*
+	 * Poll until memory is initialized.
+	 * 512 Meg at 400 might hit this 200 times or so.
+	 */
+	while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) {
+		udelay(1000);
+	}
+	debug("DDR: memory initialized\n\n");
+	asm("sync; isync");
+	udelay(500);
+#endif
+
+	return 512 * 1024 * 1024;
+}
+
+#endif
+
+#ifdef CONFIG_PCI1
+static struct pci_controller pci1_hose;
+#endif
+
+#ifdef CONFIG_PCIE1
+static struct pci_controller pcie1_hose;
+#endif
+
+#ifdef CONFIG_PCIE2
+static struct pci_controller pcie2_hose;
+#endif
+
+#ifdef CONFIG_PCIE3
+static struct pci_controller pcie3_hose;
+#endif
+
+int first_free_busno=0;
+
+void
+pci_init_board(void)
+{
+	volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
+	uint devdisr = gur->devdisr;
+	uint sdrs2_io_sel =
+		(gur->pordevsr & MPC85xx_PORDEVSR_SRDS2_IO_SEL) >> 27;
+	uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
+	uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
+
+	debug("   pci_init_board: devdisr=%x, sdrs2_io_sel=%x, io_sel=%x,\
+		host_agent=%x\n", devdisr, sdrs2_io_sel, io_sel, host_agent);
+
+	if (sdrs2_io_sel == 7)
+		printf("    Serdes2 disalbed\n");
+	else if (sdrs2_io_sel == 4) {
+		printf("    eTSEC1 is in sgmii mode.\n");
+		printf("    eTSEC3 is in sgmii mode.\n");
+	} else if (sdrs2_io_sel == 6)
+		printf("    eTSEC1 is in sgmii mode.\n");
+
+#ifdef CONFIG_PCIE3
+{
+	volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE3_ADDR;
+	extern void fsl_pci_init(struct pci_controller *hose);
+	struct pci_controller *hose = &pcie3_hose;
+	int pcie_ep = (host_agent == 1);
+	int pcie_configured  = (io_sel == 7);
+
+	if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
+		printf ("\n    PCIE3 connected to Slot3 as %s (base address %x)",
+			pcie_ep ? "End Point" : "Root Complex",
+			(uint)pci);
+		if (pci->pme_msg_det) {
+			pci->pme_msg_det = 0xffffffff;
+			debug (" with errors.  Clearing.  Now 0x%08x",pci->pme_msg_det);
+		}
+		printf ("\n");
+
+		/* inbound */
+		pci_set_region(hose->regions + 0,
+			       CFG_PCI_MEMORY_BUS,
+			       CFG_PCI_MEMORY_PHYS,
+			       CFG_PCI_MEMORY_SIZE,
+			       PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+		/* outbound memory */
+		pci_set_region(hose->regions + 1,
+			       CFG_PCIE3_MEM_BASE,
+			       CFG_PCIE3_MEM_PHYS,
+			       CFG_PCIE3_MEM_SIZE,
+			       PCI_REGION_MEM);
+
+		/* outbound io */
+		pci_set_region(hose->regions + 2,
+			       CFG_PCIE3_IO_BASE,
+			       CFG_PCIE3_IO_PHYS,
+			       CFG_PCIE3_IO_SIZE,
+			       PCI_REGION_IO);
+
+		hose->region_count = 3;
+
+		hose->first_busno=first_free_busno;
+		pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
+
+		fsl_pci_init(hose);
+
+		first_free_busno=hose->last_busno+1;
+		printf ("    PCIE3 on bus %02x - %02x\n",
+			hose->first_busno,hose->last_busno);
+	} else {
+		printf ("    PCIE3: disabled\n");
+	}
+
+ }
+#else
+	gur->devdisr |= MPC85xx_DEVDISR_PCIE3; /* disable */
+#endif
+
+#ifdef CONFIG_PCIE1
+ {
+	volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE1_ADDR;
+	extern void fsl_pci_init(struct pci_controller *hose);
+	struct pci_controller *hose = &pcie1_hose;
+	int pcie_ep = (host_agent == 5);
+	int pcie_configured  = (io_sel == 2 || io_sel == 3
+				|| io_sel == 5 || io_sel == 7);
+
+	if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
+		printf ("\n    PCIE1 connected to Slot1 as %s (base address %x)",
+			pcie_ep ? "End Point" : "Root Complex",
+			(uint)pci);
+		if (pci->pme_msg_det) {
+			pci->pme_msg_det = 0xffffffff;
+			debug (" with errors.  Clearing.  Now 0x%08x",pci->pme_msg_det);
+		}
+		printf ("\n");
+
+		/* inbound */
+		pci_set_region(hose->regions + 0,
+			       CFG_PCI_MEMORY_BUS,
+			       CFG_PCI_MEMORY_PHYS,
+			       CFG_PCI_MEMORY_SIZE,
+			       PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+		/* outbound memory */
+		pci_set_region(hose->regions + 1,
+			       CFG_PCIE1_MEM_BASE,
+			       CFG_PCIE1_MEM_PHYS,
+			       CFG_PCIE1_MEM_SIZE,
+			       PCI_REGION_MEM);
+
+		/* outbound io */
+		pci_set_region(hose->regions + 2,
+			       CFG_PCIE1_IO_BASE,
+			       CFG_PCIE1_IO_PHYS,
+			       CFG_PCIE1_IO_SIZE,
+			       PCI_REGION_IO);
+
+		hose->region_count = 3;
+#ifdef CFG_PCIE1_MEM_BASE2
+		/* outbound memory */
+		pci_set_region(hose->regions + 3,
+			       CFG_PCIE1_MEM_BASE2,
+			       CFG_PCIE1_MEM_PHYS2,
+			       CFG_PCIE1_MEM_SIZE2,
+			       PCI_REGION_MEM);
+		hose->region_count++;
+#endif
+		hose->first_busno=first_free_busno;
+
+		pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
+
+		fsl_pci_init(hose);
+
+		first_free_busno=hose->last_busno+1;
+		printf("    PCIE1 on bus %02x - %02x\n",
+		       hose->first_busno,hose->last_busno);
+
+	} else {
+		printf ("    PCIE1: disabled\n");
+	}
+
+ }
+#else
+	gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
+#endif
+
+#ifdef CONFIG_PCIE2
+ {
+	volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE2_ADDR;
+	extern void fsl_pci_init(struct pci_controller *hose);
+	struct pci_controller *hose = &pcie2_hose;
+	int pcie_ep = (host_agent == 3);
+	int pcie_configured  = (io_sel == 5 || io_sel == 7);
+
+	if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
+		printf ("\n    PCIE2 connected to Slot 2 as %s (base address %x)",
+			pcie_ep ? "End Point" : "Root Complex",
+			(uint)pci);
+		if (pci->pme_msg_det) {
+			pci->pme_msg_det = 0xffffffff;
+			debug (" with errors.  Clearing.  Now 0x%08x",pci->pme_msg_det);
+		}
+		printf ("\n");
+
+		/* inbound */
+		pci_set_region(hose->regions + 0,
+			       CFG_PCI_MEMORY_BUS,
+			       CFG_PCI_MEMORY_PHYS,
+			       CFG_PCI_MEMORY_SIZE,
+			       PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+		/* outbound memory */
+		pci_set_region(hose->regions + 1,
+			       CFG_PCIE2_MEM_BASE,
+			       CFG_PCIE2_MEM_PHYS,
+			       CFG_PCIE2_MEM_SIZE,
+			       PCI_REGION_MEM);
+
+		/* outbound io */
+		pci_set_region(hose->regions + 2,
+			       CFG_PCIE2_IO_BASE,
+			       CFG_PCIE2_IO_PHYS,
+			       CFG_PCIE2_IO_SIZE,
+			       PCI_REGION_IO);
+
+		hose->region_count = 3;
+#ifdef CFG_PCIE2_MEM_BASE2
+		/* outbound memory */
+		pci_set_region(hose->regions + 3,
+			       CFG_PCIE2_MEM_BASE2,
+			       CFG_PCIE2_MEM_PHYS2,
+			       CFG_PCIE2_MEM_SIZE2,
+			       PCI_REGION_MEM);
+		hose->region_count++;
+#endif
+		hose->first_busno=first_free_busno;
+		pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
+
+		fsl_pci_init(hose);
+		first_free_busno=hose->last_busno+1;
+		printf ("    PCIE2 on bus %02x - %02x\n",
+			hose->first_busno,hose->last_busno);
+
+	} else {
+		printf ("    PCIE2: disabled\n");
+	}
+
+ }
+#else
+	gur->devdisr |= MPC85xx_DEVDISR_PCIE2; /* disable */
+#endif
+
+
+#ifdef CONFIG_PCI1
+{
+	volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCI1_ADDR;
+	extern void fsl_pci_init(struct pci_controller *hose);
+	struct pci_controller *hose = &pci1_hose;
+
+	uint pci_agent = (host_agent == 6);
+	uint pci_speed = 66666000; /*get_clock_freq (); PCI PSPEED in [4:5] */
+	uint pci_32 = 1;
+	uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB;	/* PORDEVSR[14] */
+	uint pci_clk_sel = gur->porpllsr & MPC85xx_PORDEVSR_PCI1_SPD;	/* PORPLLSR[16] */
+
+
+	if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
+		printf ("\n    PCI: %d bit, %s MHz, %s, %s, %s (base address %x)\n",
+			(pci_32) ? 32 : 64,
+			(pci_speed == 33333000) ? "33" :
+			(pci_speed == 66666000) ? "66" : "unknown",
+			pci_clk_sel ? "sync" : "async",
+			pci_agent ? "agent" : "host",
+			pci_arb ? "arbiter" : "external-arbiter",
+			(uint)pci
+			);
+
+		/* inbound */
+		pci_set_region(hose->regions + 0,
+			       CFG_PCI_MEMORY_BUS,
+			       CFG_PCI_MEMORY_PHYS,
+			       CFG_PCI_MEMORY_SIZE,
+			       PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+		/* outbound memory */
+		pci_set_region(hose->regions + 1,
+			       CFG_PCI1_MEM_BASE,
+			       CFG_PCI1_MEM_PHYS,
+			       CFG_PCI1_MEM_SIZE,
+			       PCI_REGION_MEM);
+
+		/* outbound io */
+		pci_set_region(hose->regions + 2,
+			       CFG_PCI1_IO_BASE,
+			       CFG_PCI1_IO_PHYS,
+			       CFG_PCI1_IO_SIZE,
+			       PCI_REGION_IO);
+		hose->region_count = 3;
+#ifdef CFG_PCI1_MEM_BASE2
+		/* outbound memory */
+		pci_set_region(hose->regions + 3,
+			       CFG_PCI1_MEM_BASE2,
+			       CFG_PCI1_MEM_PHYS2,
+			       CFG_PCI1_MEM_SIZE2,
+			       PCI_REGION_MEM);
+		hose->region_count++;
+#endif
+		hose->first_busno=first_free_busno;
+		pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
+
+		fsl_pci_init(hose);
+		first_free_busno=hose->last_busno+1;
+		printf ("PCI on bus %02x - %02x\n",
+			hose->first_busno,hose->last_busno);
+	} else {
+		printf ("    PCI: disabled\n");
+	}
+}
+#else
+	gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */
+#endif
+}
+
+
+int board_early_init_r(void)
+{
+	unsigned int i;
+	const unsigned int flashbase = CFG_FLASH_BASE;
+	const u8 flash_esel = 1;
+
+	/*
+	 * Remap Boot flash + PROMJET region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Invalidate any remaining lines of the flash from caches. */
+	for (i = 0; i < 256*1024*1024; i+=32) {
+		asm volatile ("dcbi %0,%1": : "b" (flashbase), "r" (i));
+		asm volatile ("icbi %0,%1": : "b" (flashbase), "r" (i));
+	}
+
+	/* invalidate existing TLB entry for flash + promjet */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, flashbase,		/* tlb, epn, rpn */
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,	/* perms, wimge */
+		0, flash_esel, BOOKE_PAGESZ_256M, 1);	/* ts, esel, tsize, iprot */
+
+	return 0;
+}
+
+#ifdef CONFIG_GET_CLK_FROM_ICS307
+/* decode S[0-2] to Output Divider (OD) */
+static unsigned char
+ics307_S_to_OD[] = {
+	10, 2, 8, 4, 5, 7, 3, 6
+};
+
+/* Calculate frequency being generated by ICS307-02 clock chip based upon
+ * the control bytes being programmed into it. */
+/* XXX: This function should probably go into a common library */
+static unsigned long
+ics307_clk_freq (unsigned char cw0, unsigned char cw1, unsigned char cw2)
+{
+	const unsigned long long InputFrequency = CONFIG_ICS307_REFCLK_HZ;
+	unsigned long VDW = ((cw1 << 1) & 0x1FE) + ((cw2 >> 7) & 1);
+	unsigned long RDW = cw2 & 0x7F;
+	unsigned long OD = ics307_S_to_OD[cw0 & 0x7];
+	unsigned long freq;
+
+	/* CLK1Frequency = InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD) */
+
+	/* cw0:  C1 C0 TTL F1 F0 S2 S1 S0
+	 * cw1:  V8 V7 V6 V5 V4 V3 V2 V1
+	 * cw2:  V0 R6 R5 R4 R3 R2 R1 R0
+	 *
+	 * R6:R0 = Reference Divider Word (RDW)
+	 * V8:V0 = VCO Divider Word (VDW)
+	 * S2:S0 = Output Divider Select (OD)
+	 * F1:F0 = Function of CLK2 Output
+	 * TTL = duty cycle
+	 * C1:C0 = internal load capacitance for cyrstal
+	 */
+
+	/* Adding 1 to get a "nicely" rounded number, but this needs
+	 * more tweaking to get a "properly" rounded number. */
+
+	freq = 1 + (InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD));
+
+	debug("ICS307: CW[0-2]: %02X %02X %02X => %u Hz\n", cw0, cw1, cw2,
+		freq);
+	return freq;
+}
+
+unsigned long
+get_board_sys_clk(ulong dummy)
+{
+	return ics307_clk_freq (
+	    in8(PIXIS_BASE + PIXIS_VSYSCLK0),
+	    in8(PIXIS_BASE + PIXIS_VSYSCLK1),
+	    in8(PIXIS_BASE + PIXIS_VSYSCLK2)
+	);
+}
+
+unsigned long
+get_board_ddr_clk(ulong dummy)
+{
+	return ics307_clk_freq (
+	    in8(PIXIS_BASE + PIXIS_VDDRCLK0),
+	    in8(PIXIS_BASE + PIXIS_VDDRCLK1),
+	    in8(PIXIS_BASE + PIXIS_VDDRCLK2)
+	);
+}
+#else
+unsigned long
+get_board_sys_clk(ulong dummy)
+{
+	u8 i;
+	ulong val = 0;
+
+	i = in8(PIXIS_BASE + PIXIS_SPD);
+	i &= 0x07;
+
+	switch (i) {
+	case 0:
+		val = 33333333;
+		break;
+	case 1:
+		val = 40000000;
+		break;
+	case 2:
+		val = 50000000;
+		break;
+	case 3:
+		val = 66666666;
+		break;
+	case 4:
+		val = 83333333;
+		break;
+	case 5:
+		val = 100000000;
+		break;
+	case 6:
+		val = 133333333;
+		break;
+	case 7:
+		val = 166666666;
+		break;
+	}
+
+	return val;
+}
+
+unsigned long
+get_board_ddr_clk(ulong dummy)
+{
+	u8 i;
+	ulong val = 0;
+
+	i = in8(PIXIS_BASE + PIXIS_SPD);
+	i &= 0x38;
+	i >>= 3;
+
+	switch (i) {
+	case 0:
+		val = 33333333;
+		break;
+	case 1:
+		val = 40000000;
+		break;
+	case 2:
+		val = 50000000;
+		break;
+	case 3:
+		val = 66666666;
+		break;
+	case 4:
+		val = 83333333;
+		break;
+	case 5:
+		val = 100000000;
+		break;
+	case 6:
+		val = 133333333;
+		break;
+	case 7:
+		val = 166666666;
+		break;
+	}
+	return val;
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_board_setup(void *blob, bd_t *bd)
+{
+	int node, tmp[2];
+	const char *path;
+
+	ft_cpu_setup(blob, bd);
+
+	node = fdt_path_offset(blob, "/aliases");
+	tmp[0] = 0;
+	if (node >= 0) {
+#ifdef CONFIG_PCI1
+		path = fdt_getprop(blob, node, "pci0", NULL);
+		if (path) {
+			tmp[1] = pci1_hose.last_busno - pci1_hose.first_busno;
+			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+		}
+#endif
+#ifdef CONFIG_PCIE2
+		path = fdt_getprop(blob, node, "pci1", NULL);
+		if (path) {
+			tmp[1] = pcie2_hose.last_busno - pcie2_hose.first_busno;
+			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+		}
+#endif
+#ifdef CONFIG_PCIE1
+		path = fdt_getprop(blob, node, "pci2", NULL);
+		if (path) {
+			tmp[1] = pcie1_hose.last_busno - pcie1_hose.first_busno;
+			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+		}
+#endif
+#ifdef CONFIG_PCIE3
+		path = fdt_getprop(blob, node, "pci3", NULL);
+		if (path) {
+			tmp[1] = pcie3_hose.last_busno - pcie3_hose.first_busno;
+			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+		}
+#endif
+	}
+}
+#endif
diff --git a/board/freescale/mpc8536ds/tlb.c b/board/freescale/mpc8536ds/tlb.c
new file mode 100644
index 0000000..28a9fa8
--- /dev/null
+++ b/board/freescale/mpc8536ds/tlb.c
@@ -0,0 +1,71 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR, CFG_INIT_RAM_ADDR,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 4 * 1024 , CFG_INIT_RAM_ADDR + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 8 * 1024 , CFG_INIT_RAM_ADDR + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 12 * 1024 , CFG_INIT_RAM_ADDR + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	SET_TLB_ENTRY(0, PIXIS_BASE, PIXIS_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CFG_CCSRBAR, CFG_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_1M, 1),
+
+	/* W**G* - Flash/promjet, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CFG_FLASH_BASE, CFG_FLASH_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CFG_PCI1_MEM_PHYS, CFG_PCI1_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CFG_PCI1_IO_PHYS, CFG_PCI1_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_256K, 1),
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/freescale/mpc8536ds/u-boot.lds b/board/freescale/mpc8536ds/u-boot.lds
new file mode 100644
index 0000000..901f633
--- /dev/null
+++ b/board/freescale/mpc8536ds/u-boot.lds
@@ -0,0 +1,145 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+PHDRS
+{
+  text PT_LOAD;
+  bss PT_LOAD;
+}
+
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text)	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data)	}
+  .rel.rodata    : { *(.rel.rodata)	}
+  .rela.rodata   : { *(.rela.rodata)	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   } :text
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  } :text
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  .bootpg ADDR(.text) + 0x7f000 :
+  {
+    cpu/mpc85xx/start.o	(.bootpg)
+  } :text = 0xffff
+
+  .resetvec ADDR(.text) + 0x7fffc :
+  {
+    *(.resetvec)
+  } :text = 0xffff
+
+  . = ADDR(.text) + 0x80000;
+
+  __bss_start = .;
+  .bss (NOLOAD)       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  } :bss
+
+  . = ALIGN(4);
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/freescale/mpc8540ads/Makefile b/board/freescale/mpc8540ads/Makefile
index 2d71cbc..4c6da4d 100644
--- a/board/freescale/mpc8540ads/Makefile
+++ b/board/freescale/mpc8540ads/Makefile
@@ -25,11 +25,14 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS-y))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
 	$(AR) $(ARFLAGS) $@ $(OBJS)
diff --git a/board/freescale/mpc8540ads/ddr.c b/board/freescale/mpc8540ads/ddr.c
new file mode 100644
index 0000000..45372f4
--- /dev/null
+++ b/board/freescale/mpc8540ads/ddr.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+
+unsigned int
+fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+
+void
+fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8540ads/mpc8540ads.c b/board/freescale/mpc8540ads/mpc8540ads.c
index 4f068cc..005e4d9 100644
--- a/board/freescale/mpc8540ads/mpc8540ads.c
+++ b/board/freescale/mpc8540ads/mpc8540ads.c
@@ -1,4 +1,4 @@
- /*
+/*
  * Copyright 2004 Freescale Semiconductor.
  * (C) Copyright 2002,2003, Motorola Inc.
  * Xianghua Xiao, (X.Xiao@motorola.com)
@@ -28,8 +28,9 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
-#include <spd_sdram.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <libfdt.h>
 #include <fdt_support.h>
 
@@ -82,10 +83,13 @@
 	}
 #endif
 
-#if defined(CONFIG_SPD_EEPROM)
-	dram_size = spd_sdram ();
+#ifdef CONFIG_SPD_EEPROM
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+
+	dram_size *= 0x100000;
 #else
-	dram_size = fixed_sdram ();
+	dram_size = fixed_sdram();
 #endif
 
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
diff --git a/board/freescale/mpc8541cds/Makefile b/board/freescale/mpc8541cds/Makefile
index 98f1530..c19a527 100644
--- a/board/freescale/mpc8541cds/Makefile
+++ b/board/freescale/mpc8541cds/Makefile
@@ -27,6 +27,7 @@
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
 COBJS-y	+= law.o
 COBJS-y	+= tlb.o
 
diff --git a/board/freescale/mpc8541cds/ddr.c b/board/freescale/mpc8541cds/ddr.c
new file mode 100644
index 0000000..11ce57d
--- /dev/null
+++ b/board/freescale/mpc8541cds/ddr.c
@@ -0,0 +1,79 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 6;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8541cds/mpc8541cds.c b/board/freescale/mpc8541cds/mpc8541cds.c
index 3669ba9..de3a791 100644
--- a/board/freescale/mpc8541cds/mpc8541cds.c
+++ b/board/freescale/mpc8541cds/mpc8541cds.c
@@ -25,7 +25,9 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <ioports.h>
 #include <spd_sdram.h>
 #include <libfdt.h>
@@ -263,7 +265,9 @@
 		udelay(200);
 	}
 #endif
-	dram_size = spd_sdram();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
 	/*
diff --git a/board/freescale/mpc8544ds/Makefile b/board/freescale/mpc8544ds/Makefile
index 3a5ea00..3997994 100644
--- a/board/freescale/mpc8544ds/Makefile
+++ b/board/freescale/mpc8544ds/Makefile
@@ -26,10 +26,13 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/freescale/mpc8544ds/ddr.c b/board/freescale/mpc8544ds/ddr.c
new file mode 100644
index 0000000..bbb5ee2
--- /dev/null
+++ b/board/freescale/mpc8544ds/ddr.c
@@ -0,0 +1,80 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 7;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c
index c39ce11..4e976b7 100644
--- a/board/freescale/mpc8544ds/mpc8544ds.c
+++ b/board/freescale/mpc8544ds/mpc8544ds.c
@@ -24,10 +24,11 @@
 #include <command.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
 #include <asm/immap_fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <asm/io.h>
-#include <spd_sdram.h>
 #include <miiphy.h>
 #include <libfdt.h>
 #include <fdt_support.h>
@@ -38,8 +39,6 @@
 extern void ddr_enable_ecc(unsigned int dram_size);
 #endif
 
-void sdram_init(void);
-
 int checkboard (void)
 {
 	volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
@@ -69,7 +68,11 @@
 
 	puts("Initializing\n");
 
-	dram_size = spd_sdram();
+	dram_size = fsl_ddr_sdram();
+
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+
+	dram_size *= 0x100000;
 
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
 	/*
diff --git a/board/freescale/mpc8548cds/Makefile b/board/freescale/mpc8548cds/Makefile
index 98f1530..c19a527 100644
--- a/board/freescale/mpc8548cds/Makefile
+++ b/board/freescale/mpc8548cds/Makefile
@@ -27,6 +27,7 @@
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
 COBJS-y	+= law.o
 COBJS-y	+= tlb.o
 
diff --git a/board/freescale/mpc8548cds/ddr.c b/board/freescale/mpc8548cds/ddr.c
new file mode 100644
index 0000000..f07d746
--- /dev/null
+++ b/board/freescale/mpc8548cds/ddr.c
@@ -0,0 +1,80 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+			unsigned int ctrl_num)
+{
+	unsigned int i;
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 7;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8548cds/mpc8548cds.c b/board/freescale/mpc8548cds/mpc8548cds.c
index 0b037cc..84d3850 100644
--- a/board/freescale/mpc8548cds/mpc8548cds.c
+++ b/board/freescale/mpc8548cds/mpc8548cds.c
@@ -25,8 +25,10 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
 #include <asm/immap_fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <spd_sdram.h>
 #include <miiphy.h>
 #include <libfdt.h>
@@ -111,7 +113,10 @@
 		udelay(200);
 	}
 #endif
-	dram_size = spd_sdram();
+
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
 	/*
@@ -119,6 +124,7 @@
 	 */
 	ddr_enable_ecc(dram_size);
 #endif
+
 	/*
 	 * SDRAM Initialization
 	 */
diff --git a/board/freescale/mpc8555cds/Makefile b/board/freescale/mpc8555cds/Makefile
index 98f1530..c19a527 100644
--- a/board/freescale/mpc8555cds/Makefile
+++ b/board/freescale/mpc8555cds/Makefile
@@ -27,6 +27,7 @@
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
 COBJS-y	+= law.o
 COBJS-y	+= tlb.o
 
diff --git a/board/freescale/mpc8555cds/ddr.c b/board/freescale/mpc8555cds/ddr.c
new file mode 100644
index 0000000..11ce57d
--- /dev/null
+++ b/board/freescale/mpc8555cds/ddr.c
@@ -0,0 +1,79 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 6;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8555cds/mpc8555cds.c b/board/freescale/mpc8555cds/mpc8555cds.c
index 9a65101..826056a 100644
--- a/board/freescale/mpc8555cds/mpc8555cds.c
+++ b/board/freescale/mpc8555cds/mpc8555cds.c
@@ -23,7 +23,9 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <ioports.h>
 #include <spd_sdram.h>
 #include <libfdt.h>
@@ -261,7 +263,10 @@
 		udelay(200);
 	}
 #endif
-	dram_size = spd_sdram();
+
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
 	/*
@@ -269,6 +274,7 @@
 	 */
 	ddr_enable_ecc(dram_size);
 #endif
+
 	/*
 	 * SDRAM Initialization
 	 */
diff --git a/board/freescale/mpc8560ads/Makefile b/board/freescale/mpc8560ads/Makefile
index 2d71cbc..67dbdeb 100644
--- a/board/freescale/mpc8560ads/Makefile
+++ b/board/freescale/mpc8560ads/Makefile
@@ -25,11 +25,14 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
+SRCS	:= $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS-y))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
 	$(AR) $(ARFLAGS) $@ $(OBJS)
diff --git a/board/freescale/mpc8560ads/ddr.c b/board/freescale/mpc8560ads/ddr.c
new file mode 100644
index 0000000..45372f4
--- /dev/null
+++ b/board/freescale/mpc8560ads/ddr.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+
+unsigned int
+fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+
+void
+fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8560ads/mpc8560ads.c b/board/freescale/mpc8560ads/mpc8560ads.c
index 2c14a88..851fc57 100644
--- a/board/freescale/mpc8560ads/mpc8560ads.c
+++ b/board/freescale/mpc8560ads/mpc8560ads.c
@@ -28,7 +28,9 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <ioports.h>
 #include <spd_sdram.h>
 #include <miiphy.h>
@@ -285,10 +287,13 @@
 	}
 #endif
 
-#if defined(CONFIG_SPD_EEPROM)
-	dram_size = spd_sdram ();
+#ifdef CONFIG_SPD_EEPROM
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+
+	dram_size *= 0x100000;
 #else
-	dram_size = fixed_sdram ();
+	dram_size = fixed_sdram();
 #endif
 
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
diff --git a/board/freescale/mpc8568mds/Makefile b/board/freescale/mpc8568mds/Makefile
index ecdc4d3..d499fb3 100644
--- a/board/freescale/mpc8568mds/Makefile
+++ b/board/freescale/mpc8568mds/Makefile
@@ -26,11 +26,15 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o bcsr.o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= bcsr.o
+COBJS-y	+= ddr.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
+SRCS	:= $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS-y))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
 	$(AR) $(ARFLAGS) $@ $(OBJS)
diff --git a/board/freescale/mpc8568mds/ddr.c b/board/freescale/mpc8568mds/ddr.c
new file mode 100644
index 0000000..1b8ecec
--- /dev/null
+++ b/board/freescale/mpc8568mds/ddr.c
@@ -0,0 +1,81 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 6;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8568mds/mpc8568mds.c b/board/freescale/mpc8568mds/mpc8568mds.c
index 2ccff7d..f9e35cc 100644
--- a/board/freescale/mpc8568mds/mpc8568mds.c
+++ b/board/freescale/mpc8568mds/mpc8568mds.c
@@ -25,8 +25,10 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
 #include <asm/immap_fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <spd_sdram.h>
 #include <i2c.h>
 #include <ioports.h>
@@ -163,7 +165,10 @@
 		udelay(200);
 	}
 #endif
-	dram_size = spd_sdram();
+
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
 	/*
@@ -171,6 +176,7 @@
 	 */
 	ddr_enable_ecc(dram_size);
 #endif
+
 	/*
 	 * SDRAM Initialization
 	 */
diff --git a/board/freescale/mpc8572ds/Makefile b/board/freescale/mpc8572ds/Makefile
new file mode 100644
index 0000000..3e82bbf
--- /dev/null
+++ b/board/freescale/mpc8572ds/Makefile
@@ -0,0 +1,54 @@
+#
+# Copyright 2007 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mpc8572ds/config.mk b/board/freescale/mpc8572ds/config.mk
new file mode 100644
index 0000000..5b32186
--- /dev/null
+++ b/board/freescale/mpc8572ds/config.mk
@@ -0,0 +1,32 @@
+#
+# Copyright 2007-2008 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8572ds board
+#
+ifndef TEXT_BASE
+TEXT_BASE = 0xeff80000
+endif
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8572=1
diff --git a/board/freescale/mpc8572ds/ddr.c b/board/freescale/mpc8572ds/ddr.c
new file mode 100644
index 0000000..5f8c555
--- /dev/null
+++ b/board/freescale/mpc8572ds/ddr.c
@@ -0,0 +1,81 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS1;
+		}
+		if (ctrl_num == 1 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS2;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 7;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 5;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/freescale/mpc8572ds/law.c b/board/freescale/mpc8572ds/law.c
new file mode 100644
index 0000000..d69b593
--- /dev/null
+++ b/board/freescale/mpc8572ds/law.c
@@ -0,0 +1,41 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CFG_FLASH_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+	SET_LAW(CFG_PCIE1_MEM_PHYS, LAWAR_SIZE_512M, LAW_TRGT_IF_PCIE_1),
+	SET_LAW(CFG_PCIE1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_1),
+	SET_LAW(CFG_PCIE2_MEM_PHYS, LAWAR_SIZE_512M, LAW_TRGT_IF_PCIE_2),
+	SET_LAW(CFG_PCIE2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_2),
+	SET_LAW(CFG_PCIE3_MEM_PHYS, LAWAR_SIZE_512M, LAW_TRGT_IF_PCIE_3),
+	SET_LAW(CFG_PCIE3_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_3),
+	SET_LAW(PIXIS_BASE, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/mpc8572ds/mpc8572ds.c b/board/freescale/mpc8572ds/mpc8572ds.c
new file mode 100644
index 0000000..70b548b
--- /dev/null
+++ b/board/freescale/mpc8572ds/mpc8572ds.c
@@ -0,0 +1,573 @@
+/*
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/immap_fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+
+#include "../common/pixis.h"
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+long int fixed_sdram(void);
+
+int checkboard (void)
+{
+	printf ("Board: MPC8572DS, System ID: 0x%02x, "
+		"System Version: 0x%02x, FPGA Version: 0x%02x\n",
+		in8(PIXIS_BASE + PIXIS_ID), in8(PIXIS_BASE + PIXIS_VER),
+		in8(PIXIS_BASE + PIXIS_PVER));
+	return 0;
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size = 0;
+
+	puts("Initializing....");
+
+#ifdef CONFIG_SPD_EEPROM
+	dram_size = fsl_ddr_sdram();
+
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+
+	dram_size *= 0x100000;
+#else
+	dram_size = fixed_sdram();
+#endif
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+	/*
+	 * Initialize and enable DDR ECC.
+	 */
+	ddr_enable_ecc(dram_size);
+#endif
+	puts("    DDR: ");
+	return dram_size;
+}
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+
+phys_size_t fixed_sdram (void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_ddr_t *ddr= &immap->im_ddr;
+	uint d_init;
+
+	ddr->cs0_bnds = CFG_DDR_CS0_BNDS;
+	ddr->cs0_config = CFG_DDR_CS0_CONFIG;
+
+	ddr->timing_cfg_3 = CFG_DDR_TIMING_3;
+	ddr->timing_cfg_0 = CFG_DDR_TIMING_0;
+	ddr->timing_cfg_1 = CFG_DDR_TIMING_1;
+	ddr->timing_cfg_2 = CFG_DDR_TIMING_2;
+	ddr->sdram_mode = CFG_DDR_MODE_1;
+	ddr->sdram_mode_2 = CFG_DDR_MODE_2;
+	ddr->sdram_interval = CFG_DDR_INTERVAL;
+	ddr->sdram_data_init = CFG_DDR_DATA_INIT;
+	ddr->sdram_clk_cntl = CFG_DDR_CLK_CTRL;
+	ddr->sdram_cfg_2 = CFG_DDR_CONTROL2;
+
+#if defined (CONFIG_DDR_ECC)
+	ddr->err_int_en = CFG_DDR_ERR_INT_EN;
+	ddr->err_disable = CFG_DDR_ERR_DIS;
+	ddr->err_sbe = CFG_DDR_SBE;
+#endif
+	asm("sync;isync");
+
+	udelay(500);
+
+	ddr->sdram_cfg = CFG_DDR_CONTROL;
+
+#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+	d_init = 1;
+	debug("DDR - 1st controller: memory initializing\n");
+	/*
+	 * Poll until memory is initialized.
+	 * 512 Meg at 400 might hit this 200 times or so.
+	 */
+	while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) {
+		udelay(1000);
+	}
+	debug("DDR: memory initialized\n\n");
+	asm("sync; isync");
+	udelay(500);
+#endif
+
+	return 512 * 1024 * 1024;
+}
+
+#endif
+
+#ifdef CONFIG_PCIE1
+static struct pci_controller pcie1_hose;
+#endif
+
+#ifdef CONFIG_PCIE2
+static struct pci_controller pcie2_hose;
+#endif
+
+#ifdef CONFIG_PCIE3
+static struct pci_controller pcie3_hose;
+#endif
+
+int first_free_busno=0;
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+	volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
+	uint devdisr = gur->devdisr;
+	uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
+	uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
+
+	debug ("   pci_init_board: devdisr=%x, io_sel=%x, host_agent=%x\n",
+			devdisr, io_sel, host_agent);
+
+	if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII1_DIS))
+		printf ("    eTSEC1 is in sgmii mode.\n");
+	if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII2_DIS))
+		printf ("    eTSEC2 is in sgmii mode.\n");
+	if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS))
+		printf ("    eTSEC3 is in sgmii mode.\n");
+	if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII4_DIS))
+		printf ("    eTSEC4 is in sgmii mode.\n");
+
+
+#ifdef CONFIG_PCIE3
+	{
+		volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE3_ADDR;
+		extern void fsl_pci_init(struct pci_controller *hose);
+		struct pci_controller *hose = &pcie3_hose;
+		int pcie_ep = (host_agent == 0) || (host_agent == 3) ||
+			(host_agent == 5) || (host_agent == 6);
+		int pcie_configured  = io_sel >= 1;
+		u32 temp32;
+
+		if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
+			printf ("\n    PCIE3 connected to ULI as %s (base address %x)",
+					pcie_ep ? "End Point" : "Root Complex",
+					(uint)pci);
+			if (pci->pme_msg_det) {
+				pci->pme_msg_det = 0xffffffff;
+				debug (" with errors.  Clearing.  Now 0x%08x",pci->pme_msg_det);
+			}
+			printf ("\n");
+
+			/* inbound */
+			pci_set_region(hose->regions + 0,
+					CFG_PCI_MEMORY_BUS,
+					CFG_PCI_MEMORY_PHYS,
+					CFG_PCI_MEMORY_SIZE,
+					PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+			/* outbound memory */
+			pci_set_region(hose->regions + 1,
+					CFG_PCIE3_MEM_BASE,
+					CFG_PCIE3_MEM_PHYS,
+					CFG_PCIE3_MEM_SIZE,
+					PCI_REGION_MEM);
+
+			/* outbound io */
+			pci_set_region(hose->regions + 2,
+					CFG_PCIE3_IO_BASE,
+					CFG_PCIE3_IO_PHYS,
+					CFG_PCIE3_IO_SIZE,
+					PCI_REGION_IO);
+
+			hose->region_count = 3;
+			hose->first_busno=first_free_busno;
+			pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
+
+			fsl_pci_init(hose);
+
+			first_free_busno=hose->last_busno+1;
+			printf ("    PCIE3 on bus %02x - %02x\n",
+					hose->first_busno,hose->last_busno);
+
+			/*
+			 * Activate ULI1575 legacy chip by performing a fake
+			 * memory access.  Needed to make ULI RTC work.
+			 * Device 1d has the first on-board memory BAR.
+			 */
+
+			pci_hose_read_config_dword(hose, PCI_BDF(2, 0x1d, 0 ),
+					PCI_BASE_ADDRESS_1, &temp32);
+			if (temp32 >= CFG_PCIE3_MEM_PHYS) {
+				debug(" uli1572 read to %x\n", temp32);
+				in_be32((unsigned *)temp32);
+			}
+		} else {
+			printf ("    PCIE3: disabled\n");
+		}
+
+	}
+#else
+	gur->devdisr |= MPC85xx_DEVDISR_PCIE3; /* disable */
+#endif
+
+#ifdef CONFIG_PCIE2
+	{
+		volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE2_ADDR;
+		extern void fsl_pci_init(struct pci_controller *hose);
+		struct pci_controller *hose = &pcie2_hose;
+		int pcie_ep = (host_agent == 2) || (host_agent == 4) ||
+			(host_agent == 6);
+		int pcie_configured  = io_sel & 4;
+
+		if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
+			printf ("\n    PCIE2 connected to Slot 1 as %s (base address %x)",
+					pcie_ep ? "End Point" : "Root Complex",
+					(uint)pci);
+			if (pci->pme_msg_det) {
+				pci->pme_msg_det = 0xffffffff;
+				debug (" with errors.  Clearing.  Now 0x%08x",pci->pme_msg_det);
+			}
+			printf ("\n");
+
+			/* inbound */
+			pci_set_region(hose->regions + 0,
+					CFG_PCI_MEMORY_BUS,
+					CFG_PCI_MEMORY_PHYS,
+					CFG_PCI_MEMORY_SIZE,
+					PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+			/* outbound memory */
+			pci_set_region(hose->regions + 1,
+					CFG_PCIE2_MEM_BASE,
+					CFG_PCIE2_MEM_PHYS,
+					CFG_PCIE2_MEM_SIZE,
+					PCI_REGION_MEM);
+
+			/* outbound io */
+			pci_set_region(hose->regions + 2,
+					CFG_PCIE2_IO_BASE,
+					CFG_PCIE2_IO_PHYS,
+					CFG_PCIE2_IO_SIZE,
+					PCI_REGION_IO);
+
+			hose->region_count = 3;
+			hose->first_busno=first_free_busno;
+			pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
+
+			fsl_pci_init(hose);
+			first_free_busno=hose->last_busno+1;
+			printf ("    PCIE2 on bus %02x - %02x\n",
+					hose->first_busno,hose->last_busno);
+
+		} else {
+			printf ("    PCIE2: disabled\n");
+		}
+
+	}
+#else
+	gur->devdisr |= MPC85xx_DEVDISR_PCIE2; /* disable */
+#endif
+#ifdef CONFIG_PCIE1
+	{
+		volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE1_ADDR;
+		extern void fsl_pci_init(struct pci_controller *hose);
+		struct pci_controller *hose = &pcie1_hose;
+		int pcie_ep = (host_agent == 1) || (host_agent == 4) ||
+			(host_agent == 5);
+		int pcie_configured  = io_sel & 6;
+
+		if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
+			printf ("\n    PCIE1 connected to Slot 2 as %s (base address %x)",
+					pcie_ep ? "End Point" : "Root Complex",
+					(uint)pci);
+			if (pci->pme_msg_det) {
+				pci->pme_msg_det = 0xffffffff;
+				debug (" with errors.  Clearing.  Now 0x%08x",pci->pme_msg_det);
+			}
+			printf ("\n");
+
+			/* inbound */
+			pci_set_region(hose->regions + 0,
+					CFG_PCI_MEMORY_BUS,
+					CFG_PCI_MEMORY_PHYS,
+					CFG_PCI_MEMORY_SIZE,
+					PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+			/* outbound memory */
+			pci_set_region(hose->regions + 1,
+					CFG_PCIE1_MEM_BASE,
+					CFG_PCIE1_MEM_PHYS,
+					CFG_PCIE1_MEM_SIZE,
+					PCI_REGION_MEM);
+
+			/* outbound io */
+			pci_set_region(hose->regions + 2,
+					CFG_PCIE1_IO_BASE,
+					CFG_PCIE1_IO_PHYS,
+					CFG_PCIE1_IO_SIZE,
+					PCI_REGION_IO);
+
+			hose->region_count = 3;
+			hose->first_busno=first_free_busno;
+
+			pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
+
+			fsl_pci_init(hose);
+
+			first_free_busno=hose->last_busno+1;
+			printf("    PCIE1 on bus %02x - %02x\n",
+					hose->first_busno,hose->last_busno);
+
+		} else {
+			printf ("    PCIE1: disabled\n");
+		}
+
+	}
+#else
+	gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
+#endif
+}
+#endif
+
+int board_early_init_r(void)
+{
+	unsigned int i;
+	const unsigned int flashbase = CFG_FLASH_BASE;
+	const u8 flash_esel = 2;
+
+	/*
+	 * Remap Boot flash + PROMJET region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Invalidate any remaining lines of the flash from caches. */
+	for (i = 0; i < 256*1024*1024; i+=32) {
+		asm volatile ("dcbi %0,%1": : "b" (flashbase), "r" (i));
+		asm volatile ("icbi %0,%1": : "b" (flashbase), "r" (i));
+	}
+
+	/* invalidate existing TLB entry for flash + promjet */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, flashbase,		/* tlb, epn, rpn */
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,	/* perms, wimge */
+			0, flash_esel, BOOKE_PAGESZ_256M, 1);	/* ts, esel, tsize, iprot */
+
+	return 0;
+}
+
+#ifdef CONFIG_GET_CLK_FROM_ICS307
+/* decode S[0-2] to Output Divider (OD) */
+static unsigned char ics307_S_to_OD[] = {
+	10, 2, 8, 4, 5, 7, 3, 6
+};
+
+/* Calculate frequency being generated by ICS307-02 clock chip based upon
+ * the control bytes being programmed into it. */
+/* XXX: This function should probably go into a common library */
+static unsigned long
+ics307_clk_freq (unsigned char cw0, unsigned char cw1, unsigned char cw2)
+{
+	const unsigned long InputFrequency = CONFIG_ICS307_REFCLK_HZ;
+	unsigned long VDW = ((cw1 << 1) & 0x1FE) + ((cw2 >> 7) & 1);
+	unsigned long RDW = cw2 & 0x7F;
+	unsigned long OD = ics307_S_to_OD[cw0 & 0x7];
+	unsigned long freq;
+
+	/* CLK1Frequency = InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD) */
+
+	/* cw0:  C1 C0 TTL F1 F0 S2 S1 S0
+	 * cw1:  V8 V7 V6 V5 V4 V3 V2 V1
+	 * cw2:  V0 R6 R5 R4 R3 R2 R1 R0
+	 *
+	 * R6:R0 = Reference Divider Word (RDW)
+	 * V8:V0 = VCO Divider Word (VDW)
+	 * S2:S0 = Output Divider Select (OD)
+	 * F1:F0 = Function of CLK2 Output
+	 * TTL = duty cycle
+	 * C1:C0 = internal load capacitance for cyrstal
+	 */
+
+	/* Adding 1 to get a "nicely" rounded number, but this needs
+	 * more tweaking to get a "properly" rounded number. */
+
+	freq = 1 + (InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD));
+
+	debug("ICS307: CW[0-2]: %02X %02X %02X => %u Hz\n", cw0, cw1, cw2,
+			freq);
+	return freq;
+}
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+	return ics307_clk_freq (
+			in8(PIXIS_BASE + PIXIS_VSYSCLK0),
+			in8(PIXIS_BASE + PIXIS_VSYSCLK1),
+			in8(PIXIS_BASE + PIXIS_VSYSCLK2)
+			);
+}
+
+unsigned long get_board_ddr_clk(ulong dummy)
+{
+	return ics307_clk_freq (
+			in8(PIXIS_BASE + PIXIS_VDDRCLK0),
+			in8(PIXIS_BASE + PIXIS_VDDRCLK1),
+			in8(PIXIS_BASE + PIXIS_VDDRCLK2)
+			);
+}
+#else
+unsigned long get_board_sys_clk(ulong dummy)
+{
+	u8 i;
+	ulong val = 0;
+
+	i = in8(PIXIS_BASE + PIXIS_SPD);
+	i &= 0x07;
+
+	switch (i) {
+		case 0:
+			val = 33333333;
+			break;
+		case 1:
+			val = 40000000;
+			break;
+		case 2:
+			val = 50000000;
+			break;
+		case 3:
+			val = 66666666;
+			break;
+		case 4:
+			val = 83333333;
+			break;
+		case 5:
+			val = 100000000;
+			break;
+		case 6:
+			val = 133333333;
+			break;
+		case 7:
+			val = 166666666;
+			break;
+	}
+
+	return val;
+}
+
+unsigned long get_board_ddr_clk(ulong dummy)
+{
+	u8 i;
+	ulong val = 0;
+
+	i = in8(PIXIS_BASE + PIXIS_SPD);
+	i &= 0x38;
+	i >>= 3;
+
+	switch (i) {
+		case 0:
+			val = 33333333;
+			break;
+		case 1:
+			val = 40000000;
+			break;
+		case 2:
+			val = 50000000;
+			break;
+		case 3:
+			val = 66666666;
+			break;
+		case 4:
+			val = 83333333;
+			break;
+		case 5:
+			val = 100000000;
+			break;
+		case 6:
+			val = 133333333;
+			break;
+		case 7:
+			val = 166666666;
+			break;
+	}
+	return val;
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	int node, tmp[2];
+	const char *path;
+	ulong base, size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+	node = fdt_path_offset(blob, "/aliases");
+	tmp[0] = 0;
+	if (node >= 0) {
+#ifdef CONFIG_PCIE3
+		path = fdt_getprop(blob, node, "pci0", NULL);
+		if (path) {
+			tmp[1] = pcie3_hose.last_busno - pcie3_hose.first_busno;
+			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+		}
+#endif
+#ifdef CONFIG_PCIE2
+		path = fdt_getprop(blob, node, "pci1", NULL);
+		if (path) {
+			tmp[1] = pcie2_hose.last_busno - pcie2_hose.first_busno;
+			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+		}
+#endif
+#ifdef CONFIG_PCIE1
+		path = fdt_getprop(blob, node, "pci2", NULL);
+		if (path) {
+			tmp[1] = pcie1_hose.last_busno - pcie1_hose.first_busno;
+			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
+		}
+#endif
+	}
+}
+#endif
+
+#ifdef CONFIG_MP
+extern void cpu_mp_lmb_reserve(struct lmb *lmb);
+
+void board_lmb_reserve(struct lmb *lmb)
+{
+	cpu_mp_lmb_reserve(lmb);
+}
+#endif
diff --git a/board/freescale/mpc8572ds/tlb.c b/board/freescale/mpc8572ds/tlb.c
new file mode 100644
index 0000000..965356a
--- /dev/null
+++ b/board/freescale/mpc8572ds/tlb.c
@@ -0,0 +1,85 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR, CFG_INIT_RAM_ADDR,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 4 * 1024 , CFG_INIT_RAM_ADDR + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 8 * 1024 , CFG_INIT_RAM_ADDR + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 12 * 1024 , CFG_INIT_RAM_ADDR + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	SET_TLB_ENTRY(0, PIXIS_BASE, PIXIS_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I,
+		      0, 0, BOOKE_PAGESZ_4K, 1),
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CFG_CCSRBAR, CFG_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_1M, 1),
+
+	/* W**G* - Flash/promjet, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CFG_FLASH_BASE, CFG_FLASH_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CFG_PCIE3_MEM_PHYS, CFG_PCIE3_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CFG_PCIE3_MEM_PHYS + 0x40000000, CFG_PCIE3_MEM_PHYS + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_256M, 1),
+
+	SET_TLB_ENTRY(1, CFG_PCIE3_MEM_PHYS + 0x50000000, CFG_PCIE3_MEM_PHYS + 0x50000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 5, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CFG_PCIE3_IO_PHYS, CFG_PCIE3_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 6, BOOKE_PAGESZ_256K, 1),
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/freescale/mpc8572ds/u-boot.lds b/board/freescale/mpc8572ds/u-boot.lds
new file mode 100644
index 0000000..a05ece5
--- /dev/null
+++ b/board/freescale/mpc8572ds/u-boot.lds
@@ -0,0 +1,145 @@
+/*
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+PHDRS
+{
+  text PT_LOAD;
+  bss PT_LOAD;
+}
+
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text)	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data)	}
+  .rel.rodata    : { *(.rel.rodata)	}
+  .rela.rodata   : { *(.rela.rodata)	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   } :text
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  } :text
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  .bootpg ADDR(.text) + 0x7f000 :
+  {
+    cpu/mpc85xx/start.o	(.bootpg)
+  } :text = 0xffff
+
+  .resetvec ADDR(.text) + 0x7fffc :
+  {
+    *(.resetvec)
+  } :text = 0xffff
+
+  . = ADDR(.text) + 0x80000;
+
+  __bss_start = .;
+  .bss (NOLOAD)       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  } :bss
+
+  . = ALIGN(4);
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/mpc8540eval/Makefile b/board/mpc8540eval/Makefile
index 325d6d5..5a68f11 100644
--- a/board/mpc8540eval/Makefile
+++ b/board/mpc8540eval/Makefile
@@ -25,10 +25,14 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o flash.o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-y	+= flash.o
+COBJS-$(CONFIG_FSL_DDR1) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/mpc8540eval/ddr.c b/board/mpc8540eval/ddr.c
new file mode 100644
index 0000000..45372f4
--- /dev/null
+++ b/board/mpc8540eval/ddr.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+
+unsigned int
+fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+
+void
+fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/mpc8540eval/mpc8540eval.c b/board/mpc8540eval/mpc8540eval.c
index 1ac333c..7c54458 100644
--- a/board/mpc8540eval/mpc8540eval.c
+++ b/board/mpc8540eval/mpc8540eval.c
@@ -25,7 +25,9 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <spd_sdram.h>
 
 long int fixed_sdram (void);
@@ -84,7 +86,9 @@
 #endif
 
 #if defined(CONFIG_SPD_EEPROM)
-	dram_size = spd_sdram ();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 #else
 	dram_size = fixed_sdram ();
 #endif
diff --git a/board/pm854/Makefile b/board/pm854/Makefile
index 2d71cbc..52a756c 100644
--- a/board/pm854/Makefile
+++ b/board/pm854/Makefile
@@ -25,10 +25,13 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-$(CONFIG_FSL_DDR1) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/pm854/ddr.c b/board/pm854/ddr.c
new file mode 100644
index 0000000..45372f4
--- /dev/null
+++ b/board/pm854/ddr.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+
+unsigned int
+fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+
+void
+fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/pm854/pm854.c b/board/pm854/pm854.c
index 555f6c0..7dbafb9 100644
--- a/board/pm854/pm854.c
+++ b/board/pm854/pm854.c
@@ -28,7 +28,9 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <spd_sdram.h>
 
 #if defined(CONFIG_DDR_ECC)
@@ -105,7 +107,9 @@
 #endif
 
 #if defined(CONFIG_SPD_EEPROM)
-	dram_size = spd_sdram ();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 #else
 	dram_size = fixed_sdram ();
 #endif
diff --git a/board/pm856/Makefile b/board/pm856/Makefile
index 2d71cbc..52a756c 100644
--- a/board/pm856/Makefile
+++ b/board/pm856/Makefile
@@ -25,10 +25,13 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-$(CONFIG_FSL_DDR1) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/pm856/ddr.c b/board/pm856/ddr.c
new file mode 100644
index 0000000..45372f4
--- /dev/null
+++ b/board/pm856/ddr.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+
+unsigned int
+fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+
+void
+fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/pm856/pm856.c b/board/pm856/pm856.c
index bf325f8..bd4c065 100644
--- a/board/pm856/pm856.c
+++ b/board/pm856/pm856.c
@@ -28,7 +28,9 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <ioports.h>
 #include <spd_sdram.h>
 #include <miiphy.h>
@@ -260,7 +262,9 @@
 #endif
 
 #if defined(CONFIG_SPD_EEPROM)
-	dram_size = spd_sdram ();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 #else
 	dram_size = fixed_sdram ();
 #endif
diff --git a/board/sbc8548/Makefile b/board/sbc8548/Makefile
index bb96d95..9919a6e 100644
--- a/board/sbc8548/Makefile
+++ b/board/sbc8548/Makefile
@@ -28,10 +28,13 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-$(CONFIG_FSL_DDR2) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/sbc8548/ddr.c b/board/sbc8548/ddr.c
new file mode 100644
index 0000000..f07d746
--- /dev/null
+++ b/board/sbc8548/ddr.c
@@ -0,0 +1,80 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+			unsigned int ctrl_num)
+{
+	unsigned int i;
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 7;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c
index 91b40e5..f31d7d6 100644
--- a/board/sbc8548/sbc8548.c
+++ b/board/sbc8548/sbc8548.c
@@ -30,6 +30,7 @@
 #include <asm/processor.h>
 #include <asm/immap_85xx.h>
 #include <asm/immap_fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <spd_sdram.h>
 #include <miiphy.h>
 #include <libfdt.h>
@@ -106,7 +107,9 @@
 #endif
 
 #if defined(CONFIG_SPD_EEPROM)
-	dram_size = spd_sdram ();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 #else
 	dram_size = fixed_sdram ();
 #endif
diff --git a/board/sbc8560/Makefile b/board/sbc8560/Makefile
index bb96d95..6399734 100644
--- a/board/sbc8560/Makefile
+++ b/board/sbc8560/Makefile
@@ -28,10 +28,13 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-$(CONFIG_FSL_DDR1) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/sbc8560/ddr.c b/board/sbc8560/ddr.c
new file mode 100644
index 0000000..45372f4
--- /dev/null
+++ b/board/sbc8560/ddr.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+
+unsigned int
+fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+
+void
+fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/sbc8560/sbc8560.c b/board/sbc8560/sbc8560.c
index d9e598c..dc66170 100644
--- a/board/sbc8560/sbc8560.c
+++ b/board/sbc8560/sbc8560.c
@@ -29,7 +29,9 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <ioports.h>
 #include <spd_sdram.h>
 #include <miiphy.h>
@@ -283,7 +285,9 @@
 #endif
 
 #if defined(CONFIG_SPD_EEPROM)
-	dram_size = spd_sdram ();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 #else
 	dram_size = fixed_sdram ();
 #endif
diff --git a/board/sbc8560/u-boot.lds b/board/sbc8560/u-boot.lds
index ba5ce0b..237a3b6 100644
--- a/board/sbc8560/u-boot.lds
+++ b/board/sbc8560/u-boot.lds
@@ -74,7 +74,6 @@
     cpu/mpc85xx/cpu_init.o (.text)
     cpu/mpc85xx/cpu.o (.text)
     cpu/mpc85xx/speed.o (.text)
-    cpu/mpc85xx/spd_sdram.o (.text)
     common/dlmalloc.o (.text)
     lib_generic/crc32.o (.text)
     lib_ppc/extable.o (.text)
diff --git a/board/socrates/Makefile b/board/socrates/Makefile
index a41fead..6fae601 100644
--- a/board/socrates/Makefile
+++ b/board/socrates/Makefile
@@ -28,10 +28,15 @@
 LIB	= $(obj)lib$(BOARD).a
 #
 
-COBJS	:= $(BOARD).o law.o tlb.o sdram.o nand.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-y	+= nand.o
+COBJS-y	+= sdram.o
+COBJS-$(CONFIG_FSL_DDR2) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/socrates/ddr.c b/board/socrates/ddr.c
new file mode 100644
index 0000000..bbb5ee2
--- /dev/null
+++ b/board/socrates/ddr.c
@@ -0,0 +1,80 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 7;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/socrates/sdram.c b/board/socrates/sdram.c
index 768fe05..12d1b8a 100644
--- a/board/socrates/sdram.c
+++ b/board/socrates/sdram.c
@@ -25,6 +25,7 @@
 #include <common.h>
 #include <asm/processor.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <asm/processor.h>
 #include <asm/mmu.h>
 #include <spd_sdram.h>
@@ -80,7 +81,9 @@
 {
 	long dram_size = 0;
 #if defined(CONFIG_SPD_EEPROM)
-	dram_size = spd_sdram ();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 #else
 	dram_size = sdram_setup(CONFIG_DDR_DEFAULT_CL);
 #endif
diff --git a/board/stxgp3/Makefile b/board/stxgp3/Makefile
index 325d6d5..5a68f11 100644
--- a/board/stxgp3/Makefile
+++ b/board/stxgp3/Makefile
@@ -25,10 +25,14 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o flash.o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-y	+= flash.o
+COBJS-$(CONFIG_FSL_DDR1) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/stxgp3/ddr.c b/board/stxgp3/ddr.c
new file mode 100644
index 0000000..45372f4
--- /dev/null
+++ b/board/stxgp3/ddr.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+
+unsigned int
+fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+
+void
+fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/stxgp3/stxgp3.c b/board/stxgp3/stxgp3.c
index 218e805..c80f1b3 100644
--- a/board/stxgp3/stxgp3.c
+++ b/board/stxgp3/stxgp3.c
@@ -32,7 +32,9 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <ioports.h>
 #include <asm/io.h>
 #include <spd_sdram.h>
@@ -292,7 +294,9 @@
 	}
 #endif
 
-	dram_size = spd_sdram ();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 
 #if defined(CONFIG_DDR_ECC)
 	/* Initialize and enable DDR ECC.
diff --git a/board/stxgp3/u-boot.lds b/board/stxgp3/u-boot.lds
index 9cc4997..d5363be 100644
--- a/board/stxgp3/u-boot.lds
+++ b/board/stxgp3/u-boot.lds
@@ -76,7 +76,6 @@
     cpu/mpc85xx/cpu_init.o (.text)
     cpu/mpc85xx/cpu.o (.text)
     cpu/mpc85xx/speed.o (.text)
-    cpu/mpc85xx/spd_sdram.o (.text)
     common/dlmalloc.o (.text)
     lib_generic/crc32.o (.text)
     lib_ppc/extable.o (.text)
diff --git a/board/stxssa/Makefile b/board/stxssa/Makefile
index e29cf95..9ab41ec 100644
--- a/board/stxssa/Makefile
+++ b/board/stxssa/Makefile
@@ -25,10 +25,13 @@
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o law.o tlb.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-$(CONFIG_FSL_DDR1) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/stxssa/ddr.c b/board/stxssa/ddr.c
new file mode 100644
index 0000000..45372f4
--- /dev/null
+++ b/board/stxssa/ddr.c
@@ -0,0 +1,70 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
+}
+
+
+unsigned int
+fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+
+void
+fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0) {
+			i2c_address = SPD_EEPROM_ADDRESS;
+		}
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 0;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/board/stxssa/stxssa.c b/board/stxssa/stxssa.c
index 2c4b546..124e123 100644
--- a/board/stxssa/stxssa.c
+++ b/board/stxssa/stxssa.c
@@ -32,7 +32,9 @@
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
+#include <asm/mmu.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <ioports.h>
 #include <asm/io.h>
 #include <spd_sdram.h>
@@ -308,7 +310,9 @@
 	}
 #endif
 
-	dram_size = spd_sdram ();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 
 #if defined(CONFIG_DDR_ECC)
 	/* Initialize and enable DDR ECC.
diff --git a/board/stxssa/u-boot.lds b/board/stxssa/u-boot.lds
index b0a9d68..93bedda 100644
--- a/board/stxssa/u-boot.lds
+++ b/board/stxssa/u-boot.lds
@@ -76,7 +76,6 @@
     cpu/mpc85xx/cpu_init.o (.text)
     cpu/mpc85xx/cpu.o (.text)
     cpu/mpc85xx/speed.o (.text)
-    cpu/mpc85xx/spd_sdram.o (.text)
     common/dlmalloc.o (.text)
     lib_generic/crc32.o (.text)
     lib_ppc/extable.o (.text)
diff --git a/cpu/mpc85xx/Makefile b/cpu/mpc85xx/Makefile
index d51a6dd..627e61b 100644
--- a/cpu/mpc85xx/Makefile
+++ b/cpu/mpc85xx/Makefile
@@ -34,14 +34,22 @@
 COBJS-$(CONFIG_MP) += mp.o
 COBJS-$(CONFIG_OF_LIBFDT) += fdt.o
 
-ifneq ($(CONFIG_FSL_DDR3),y)
-ifneq ($(CONFIG_FSL_DDR2),y)
-ifneq ($(CONFIG_FSL_DDR1),y)
-COBJS-y	+= spd_sdram.o
-endif
-endif
-endif
+# supports ddr1
+COBJS-$(CONFIG_MPC8540) += ddr-gen1.o
+COBJS-$(CONFIG_MPC8560) += ddr-gen1.o
+COBJS-$(CONFIG_MPC8541) += ddr-gen1.o
+COBJS-$(CONFIG_MPC8555) += ddr-gen1.o
 
+# supports ddr1/2
+COBJS-$(CONFIG_MPC8548) += ddr-gen2.o
+COBJS-$(CONFIG_MPC8568) += ddr-gen2.o
+COBJS-$(CONFIG_MPC8544) += ddr-gen2.o
+
+# supports ddr1/2/3
+COBJS-$(CONFIG_MPC8572) += ddr-gen3.o
+COBJS-$(CONFIG_MPC8536) += ddr-gen3.o
+
+COBJS-$(CONFIG_MPC8536) += mpc8536_serdes.o
 COBJS	= traps.o cpu.o cpu_init.o speed.o interrupts.o tlb.o \
 	  pci.o serial_scc.o commproc.o ether_fcc.o qe_io.o \
 	  $(COBJS-y)
diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c
index bde8e56..2fe3cea 100644
--- a/cpu/mpc85xx/cpu.c
+++ b/cpu/mpc85xx/cpu.c
@@ -36,6 +36,8 @@
 struct cpu_type cpu_type_list [] = {
 	CPU_TYPE_ENTRY(8533, 8533),
 	CPU_TYPE_ENTRY(8533, 8533_E),
+	CPU_TYPE_ENTRY(8536, 8536),
+	CPU_TYPE_ENTRY(8536, 8536_E),
 	CPU_TYPE_ENTRY(8540, 8540),
 	CPU_TYPE_ENTRY(8541, 8541),
 	CPU_TYPE_ENTRY(8541, 8541_E),
@@ -89,6 +91,9 @@
 	svr = get_svr();
 	ver = SVR_SOC_VER(svr);
 	major = SVR_MAJ(svr);
+#ifdef CONFIG_MPC8536
+	major &= 0x7; /* the msb of this nibble is a mfg code */
+#endif
 	minor = SVR_MIN(svr);
 
 	puts("CPU:   ");
@@ -154,7 +159,8 @@
 #endif
 	clkdiv = lcrr & 0x0f;
 	if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) {
-#if defined(CONFIG_MPC8548) || defined(CONFIG_MPC8544)
+#if defined(CONFIG_MPC8548) || defined(CONFIG_MPC8544) || \
+    defined(CONFIG_MPC8572) || defined(CONFIG_MPC8536)
 		/*
 		 * Yes, the entire PQ38 family use the same
 		 * bit-representation for twice the clock divider values.
diff --git a/cpu/mpc85xx/cpu_init.c b/cpu/mpc85xx/cpu_init.c
index 4feb751..783c5ba 100644
--- a/cpu/mpc85xx/cpu_init.c
+++ b/cpu/mpc85xx/cpu_init.c
@@ -37,6 +37,10 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#ifdef CONFIG_MPC8536
+extern void fsl_serdes_init(void);
+#endif
+
 #ifdef CONFIG_QE
 extern qe_iop_conf_t qe_iop_conf_tab[];
 extern void qe_config_iopin(u8 port, u8 pin, int dir,
@@ -240,6 +244,9 @@
 	/* Config QE ioports */
 	config_qe_ioports();
 #endif
+#if defined(CONFIG_MPC8536)
+	fsl_serdes_init();
+#endif
 
 }
 
diff --git a/cpu/mpc85xx/ddr-gen1.c b/cpu/mpc85xx/ddr-gen1.c
new file mode 100644
index 0000000..2c11ee4
--- /dev/null
+++ b/cpu/mpc85xx/ddr-gen1.c
@@ -0,0 +1,120 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/fsl_ddr_sdram.h>
+
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
+#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
+#endif
+
+void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
+			     unsigned int ctrl_num)
+{
+	unsigned int i;
+	volatile ccsr_ddr_t *ddr = (void *)CFG_MPC85xx_DDR_ADDR;
+
+	if (ctrl_num != 0) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		if (i == 0) {
+			out_be32(&ddr->cs0_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs0_config, regs->cs[i].config);
+
+		} else if (i == 1) {
+			out_be32(&ddr->cs1_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs1_config, regs->cs[i].config);
+
+		} else if (i == 2) {
+			out_be32(&ddr->cs2_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs2_config, regs->cs[i].config);
+
+		} else if (i == 3) {
+			out_be32(&ddr->cs3_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs3_config, regs->cs[i].config);
+		}
+	}
+
+	out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1);
+	out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2);
+	out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
+	out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
+#if defined(CONFIG_MPC8555) || defined(CONFIG_MPC8541)
+	out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
+#endif
+
+	/*
+	 * 200 painful micro-seconds must elapse between
+	 * the DDR clock setup and the DDR config enable.
+	 */
+	udelay(200);
+	asm volatile("sync;isync");
+
+	out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg);
+
+	asm("sync;isync;msync");
+	udelay(500);
+}
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void dma_init(void);
+extern uint dma_check(void);
+extern int dma_xfer(void *dest, uint count, void *src);
+
+/*
+ * Initialize all of memory for ECC, then enable errors.
+ */
+
+void
+ddr_enable_ecc(unsigned int dram_size)
+{
+	uint *p = 0;
+	uint i = 0;
+	volatile ccsr_ddr_t *ddr= (void *)(CFG_MPC85xx_DDR_ADDR);
+
+	dma_init();
+
+	for (*p = 0; p < (uint *)(8 * 1024); p++) {
+		if (((unsigned int)p & 0x1f) == 0) {
+			ppcDcbz((unsigned long) p);
+		}
+		*p = (unsigned int)CONFIG_MEM_INIT_VALUE;
+		if (((unsigned int)p & 0x1c) == 0x1c) {
+			ppcDcbf((unsigned long) p);
+		}
+	}
+
+	dma_xfer((uint *)0x002000, 0x002000, (uint *)0); /* 8K */
+	dma_xfer((uint *)0x004000, 0x004000, (uint *)0); /* 16K */
+	dma_xfer((uint *)0x008000, 0x008000, (uint *)0); /* 32K */
+	dma_xfer((uint *)0x010000, 0x010000, (uint *)0); /* 64K */
+	dma_xfer((uint *)0x020000, 0x020000, (uint *)0); /* 128k */
+	dma_xfer((uint *)0x040000, 0x040000, (uint *)0); /* 256k */
+	dma_xfer((uint *)0x080000, 0x080000, (uint *)0); /* 512k */
+	dma_xfer((uint *)0x100000, 0x100000, (uint *)0); /* 1M */
+	dma_xfer((uint *)0x200000, 0x200000, (uint *)0); /* 2M */
+	dma_xfer((uint *)0x400000, 0x400000, (uint *)0); /* 4M */
+
+	for (i = 1; i < dram_size / 0x800000; i++) {
+		dma_xfer((uint *)(0x800000*i), 0x800000, (uint *)0);
+	}
+
+	/*
+	 * Enable errors for ECC.
+	 */
+	debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable);
+	ddr->err_disable = 0x00000000;
+	asm("sync;isync;msync");
+	debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable);
+}
+
+#endif	/* CONFIG_DDR_ECC  && ! CONFIG_ECC_INIT_VIA_DDRCONTROLLER */
diff --git a/cpu/mpc85xx/ddr-gen2.c b/cpu/mpc85xx/ddr-gen2.c
new file mode 100644
index 0000000..130090c
--- /dev/null
+++ b/cpu/mpc85xx/ddr-gen2.c
@@ -0,0 +1,74 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/fsl_ddr_sdram.h>
+
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
+#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
+#endif
+
+void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
+			     unsigned int ctrl_num)
+{
+	unsigned int i;
+	volatile ccsr_ddr_t *ddr = (void *)CFG_MPC85xx_DDR_ADDR;
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		if (i == 0) {
+			out_be32(&ddr->cs0_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs0_config, regs->cs[i].config);
+
+		} else if (i == 1) {
+			out_be32(&ddr->cs1_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs1_config, regs->cs[i].config);
+
+		} else if (i == 2) {
+			out_be32(&ddr->cs2_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs2_config, regs->cs[i].config);
+
+		} else if (i == 3) {
+			out_be32(&ddr->cs3_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs3_config, regs->cs[i].config);
+		}
+	}
+
+	out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3);
+	out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0);
+	out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1);
+	out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2);
+	out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
+	out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
+	out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
+	out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
+	out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
+	out_be32(&ddr->sdram_data_init, regs->ddr_data_init);
+	out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
+	out_be32(&ddr->init_addr, regs->ddr_init_addr);
+	out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
+
+	/*
+	 * 200 painful micro-seconds must elapse between
+	 * the DDR clock setup and the DDR config enable.
+	 */
+	udelay(200);
+	asm volatile("sync;isync");
+
+	out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg);
+
+	/* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done.  */
+	while (in_be32(&ddr->sdram_cfg_2) & 0x10) {
+		udelay(10000);		/* throttle polling rate */
+	}
+}
diff --git a/cpu/mpc85xx/ddr-gen3.c b/cpu/mpc85xx/ddr-gen3.c
new file mode 100644
index 0000000..d7cc9db
--- /dev/null
+++ b/cpu/mpc85xx/ddr-gen3.c
@@ -0,0 +1,105 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/fsl_ddr_sdram.h>
+
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
+#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
+#endif
+
+void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
+			     unsigned int ctrl_num)
+{
+	unsigned int i;
+	volatile ccsr_ddr_t *ddr;
+
+	switch (ctrl_num) {
+	case 0:
+		ddr = (void *)CFG_MPC85xx_DDR_ADDR;
+		break;
+	case 1:
+		ddr = (void *)CFG_MPC85xx_DDR2_ADDR;
+		break;
+	default:
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		if (i == 0) {
+			out_be32(&ddr->cs0_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs0_config, regs->cs[i].config);
+			out_be32(&ddr->cs0_config_2, regs->cs[i].config_2);
+
+		} else if (i == 1) {
+			out_be32(&ddr->cs1_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs1_config, regs->cs[i].config);
+			out_be32(&ddr->cs1_config_2, regs->cs[i].config_2);
+
+		} else if (i == 2) {
+			out_be32(&ddr->cs2_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs2_config, regs->cs[i].config);
+			out_be32(&ddr->cs2_config_2, regs->cs[i].config_2);
+
+		} else if (i == 3) {
+			out_be32(&ddr->cs3_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs3_config, regs->cs[i].config);
+			out_be32(&ddr->cs3_config_2, regs->cs[i].config_2);
+		}
+	}
+
+	out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3);
+	out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0);
+	out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1);
+	out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2);
+	out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
+	out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
+	out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
+	out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
+	out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
+	out_be32(&ddr->sdram_data_init, regs->ddr_data_init);
+	out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
+	out_be32(&ddr->init_addr, regs->ddr_init_addr);
+	out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
+
+	out_be32(&ddr->timing_cfg_4, regs->timing_cfg_4);
+	out_be32(&ddr->timing_cfg_5, regs->timing_cfg_5);
+	out_be32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl);
+	out_be32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl);
+	out_be32(&ddr->ddr_pd_cntl, regs->ddr_pd_cntl);
+	out_be32(&ddr->ddr_sr_cntr, regs->ddr_sr_cntr);
+	out_be32(&ddr->ddr_sdram_rcw_1, regs->ddr_sdram_rcw_1);
+	out_be32(&ddr->ddr_sdram_rcw_2, regs->ddr_sdram_rcw_2);
+
+	/*
+	 * 32-bit workaround for DDR2
+	 * 32_BE
+	 */
+	if ((((in_be32(&ddr->sdram_cfg) >> 24) & 0x7) == SDRAM_TYPE_DDR2)
+	    && in_be32(&ddr->sdram_cfg_2) & 0x80000) {
+		/* set DEBUG_1[31] */
+		u32 temp = in_be32(&ddr->debug_1);
+		out_be32(&ddr->debug_1, temp | 1);
+	}
+
+	/*
+	 * 200 painful micro-seconds must elapse between
+	 * the DDR clock setup and the DDR config enable.
+	 */
+	udelay(200);
+	asm volatile("sync;isync");
+
+	out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg);
+
+	/* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done.  */
+	while (in_be32(&ddr->sdram_cfg_2) & 0x10) {
+		udelay(10000);		/* throttle polling rate */
+	}
+}
diff --git a/cpu/mpc85xx/interrupts.c b/cpu/mpc85xx/interrupts.c
index 4fe1fac..06d4d8b 100644
--- a/cpu/mpc85xx/interrupts.c
+++ b/cpu/mpc85xx/interrupts.c
@@ -31,64 +31,20 @@
 #include <watchdog.h>
 #include <command.h>
 #include <asm/processor.h>
-#include <ppc_asm.tmpl>
 
-unsigned decrementer_count;		/* count value for 1e6/HZ microseconds */
-
-static __inline__ unsigned long get_msr(void)
-{
-	unsigned long msr;
-
-	asm volatile("mfmsr %0" : "=r" (msr) :);
-	return msr;
-}
-
-static __inline__ void set_msr(unsigned long msr)
-{
-	asm volatile("mtmsr %0" : : "r" (msr));
-	asm volatile("isync");
-}
-
-static __inline__ unsigned long get_dec (void)
-{
-	unsigned long val;
-
-	asm volatile ("mfdec %0":"=r" (val):);
-
-	return val;
-}
-
-
-static __inline__ void set_dec (unsigned long val)
-{
-	if (val)
-		asm volatile ("mtdec %0"::"r" (val));
-}
-
-void enable_interrupts (void)
-{
-	set_msr (get_msr() | MSR_EE);
-}
-
-/* returns flag if MSR_EE was set before */
-int disable_interrupts (void)
-{
-	ulong msr = get_msr();
-	set_msr (msr & ~MSR_EE);
-	return ((msr & MSR_EE) != 0);
-}
-
-int interrupt_init (void)
+int interrupt_init_cpu(unsigned long *decrementer_count)
 {
 	volatile ccsr_pic_t *pic = (void *)(CFG_MPC85xx_PIC_ADDR);
 
 	pic->gcr = MPC85xx_PICGCR_RST;
-	while (pic->gcr & MPC85xx_PICGCR_RST);
+	while (pic->gcr & MPC85xx_PICGCR_RST)
+		;
 	pic->gcr = MPC85xx_PICGCR_M;
-	decrementer_count = get_tbclk() / CFG_HZ;
+
+	*decrementer_count = get_tbclk() / CFG_HZ;
+
+	/* PIE is same as DIE, dec interrupt enable */
 	mtspr(SPRN_TCR, TCR_PIE);
-	set_dec (decrementer_count);
-	set_msr (get_msr () | MSR_EE);
 
 #ifdef CONFIG_INTERRUPTS
 	pic->iivpr1 = 0x810001;	/* 50220 enable ecm interrupts */
@@ -123,9 +79,7 @@
 	return (0);
 }
 
-/*
- * Install and free a interrupt handler. Not implemented yet.
- */
+/* Install and free a interrupt handler. Not implemented yet. */
 
 void
 irq_install_handler(int vec, interrupt_handler_t *handler, void *arg)
@@ -139,55 +93,16 @@
 	return;
 }
 
-/****************************************************************************/
-
-
-volatile ulong timestamp = 0;
-
-/*
- * timer_interrupt - gets called when the decrementer overflows,
- * with interrupts disabled.
- * Trivial implementation - no need to be really accurate.
- */
-void timer_interrupt(struct pt_regs *regs)
+void timer_interrupt_cpu(struct pt_regs *regs)
 {
-	timestamp++;
-	set_dec (decrementer_count);
+	/* PIS is same as DIS, dec interrupt status */
 	mtspr(SPRN_TSR, TSR_PIS);
-#if defined(CONFIG_WATCHDOG)
-	if ((timestamp % 1000) == 0)
-		reset_85xx_watchdog();
-#endif /* CONFIG_WATCHDOG */
-}
-
-void reset_timer (void)
-{
-	timestamp = 0;
-}
-
-ulong get_timer (ulong base)
-{
-	return (timestamp - base);
-}
-
-void set_timer (ulong t)
-{
-	timestamp = t;
 }
 
 #if defined(CONFIG_CMD_IRQ)
-
-/*******************************************************************************
- *
- * irqinfo - print information about PCI devices,not implemented.
- *
- */
-int
-do_irqinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+/* irqinfo - print information about PCI devices,not implemented. */
+int do_irqinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
-	printf ("\nInterrupt-unsupported:\n");
-
 	return 0;
 }
-
 #endif
diff --git a/cpu/mpc85xx/mpc8536_serdes.c b/cpu/mpc85xx/mpc8536_serdes.c
new file mode 100644
index 0000000..ae091e6
--- /dev/null
+++ b/cpu/mpc85xx/mpc8536_serdes.c
@@ -0,0 +1,180 @@
+/*
+ * Copyright (C) 2008 Freescale Semicondutor, Inc. All rights reserved.
+ *	Dave Liu <daveliu@freescale.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <config.h>
+#include <common.h>
+#include <asm/io.h>
+#include <asm/immap_85xx.h>
+
+/* PORDEVSR register */
+#define GUTS_PORDEVSR_OFFS		0xc
+#define GUTS_PORDEVSR_SERDES2_IO_SEL	0x38000000
+#define GUTS_PORDEVSR_SERDES2_IO_SEL_SHIFT	27
+
+/* SerDes CR0 register */
+#define	FSL_SRDSCR0_OFFS	0x0
+#define FSL_SRDSCR0_TXEQA_MASK	0x00007000
+#define FSL_SRDSCR0_TXEQA_SGMII	0x00004000
+#define FSL_SRDSCR0_TXEQA_SATA	0x00001000
+#define FSL_SRDSCR0_TXEQE_MASK	0x00000700
+#define FSL_SRDSCR0_TXEQE_SGMII	0x00000400
+#define FSL_SRDSCR0_TXEQE_SATA	0x00000100
+
+/* SerDes CR1 register */
+#define FSL_SRDSCR1_OFFS	0x4
+#define FSL_SRDSCR1_LANEA_MASK	0x80200000
+#define FSL_SRDSCR1_LANEA_OFF	0x80200000
+#define FSL_SRDSCR1_LANEE_MASK	0x08020000
+#define FSL_SRDSCR1_LANEE_OFF	0x08020000
+
+/* SerDes CR2 register */
+#define FSL_SRDSCR2_OFFS	0x8
+#define FSL_SRDSCR2_EICA_MASK	0x00001f00
+#define FSL_SRDSCR2_EICA_SGMII	0x00000400
+#define FSL_SRDSCR2_EICA_SATA	0x00001400
+#define FSL_SRDSCR2_EICE_MASK	0x0000001f
+#define FSL_SRDSCR2_EICE_SGMII	0x00000004
+#define FSL_SRDSCR2_EICE_SATA	0x00000014
+
+/* SerDes CR3 register */
+#define FSL_SRDSCR3_OFFS	0xc
+#define FSL_SRDSCR3_LANEA_MASK	0x3f000700
+#define FSL_SRDSCR3_LANEA_SGMII	0x00000000
+#define FSL_SRDSCR3_LANEA_SATA	0x15000500
+#define FSL_SRDSCR3_LANEE_MASK	0x003f0007
+#define FSL_SRDSCR3_LANEE_SGMII	0x00000000
+#define FSL_SRDSCR3_LANEE_SATA	0x00150005
+
+void fsl_serdes_init(void)
+{
+	void *guts = (void *)(CFG_MPC85xx_GUTS_ADDR);
+	void *sd = (void *)CFG_MPC85xx_SERDES2_ADDR;
+	u32 pordevsr = in_be32(guts + GUTS_PORDEVSR_OFFS);
+	u32 srds2_io_sel;
+	u32 tmp;
+
+	/* parse the SRDS2_IO_SEL of PORDEVSR */
+	srds2_io_sel = (pordevsr & GUTS_PORDEVSR_SERDES2_IO_SEL)
+		       >> GUTS_PORDEVSR_SERDES2_IO_SEL_SHIFT;
+
+	switch (srds2_io_sel) {
+	case 1:	/* Lane A - SATA1, Lane E - SATA2 */
+		/* CR 0 */
+		tmp = in_be32(sd + FSL_SRDSCR0_OFFS);
+		tmp &= ~FSL_SRDSCR0_TXEQA_MASK;
+		tmp |= FSL_SRDSCR0_TXEQA_SATA;
+		tmp &= ~FSL_SRDSCR0_TXEQE_MASK;
+		tmp |= FSL_SRDSCR0_TXEQE_SATA;
+		out_be32(sd + FSL_SRDSCR0_OFFS, tmp);
+		/* CR 1 */
+		tmp = in_be32(sd + FSL_SRDSCR1_OFFS);
+		tmp &= ~FSL_SRDSCR1_LANEA_MASK;
+		tmp &= ~FSL_SRDSCR1_LANEE_MASK;
+		out_be32(sd + FSL_SRDSCR1_OFFS, tmp);
+		/* CR 2 */
+		tmp = in_be32(sd + FSL_SRDSCR2_OFFS);
+		tmp &= ~FSL_SRDSCR2_EICA_MASK;
+		tmp |= FSL_SRDSCR2_EICA_SATA;
+		tmp &= ~FSL_SRDSCR2_EICE_MASK;
+		tmp |= FSL_SRDSCR2_EICE_SATA;
+		out_be32(sd + FSL_SRDSCR2_OFFS, tmp);
+		/* CR 3 */
+		tmp = in_be32(sd + FSL_SRDSCR3_OFFS);
+		tmp &= ~FSL_SRDSCR3_LANEA_MASK;
+		tmp |= FSL_SRDSCR3_LANEA_SATA;
+		tmp &= ~FSL_SRDSCR3_LANEE_MASK;
+		tmp |= FSL_SRDSCR3_LANEE_SATA;
+		out_be32(sd + FSL_SRDSCR3_OFFS, tmp);
+		break;
+	case 3: /* Lane A - SATA1, Lane E - disabled */
+		/* CR 0 */
+		tmp = in_be32(sd + FSL_SRDSCR0_OFFS);
+		tmp &= ~FSL_SRDSCR0_TXEQA_MASK;
+		tmp |= FSL_SRDSCR0_TXEQA_SATA;
+		out_be32(sd + FSL_SRDSCR0_OFFS, tmp);
+		/* CR 1 */
+		tmp = in_be32(sd + FSL_SRDSCR1_OFFS);
+		tmp &= ~FSL_SRDSCR1_LANEE_MASK;
+		tmp |= FSL_SRDSCR1_LANEE_OFF;
+		out_be32(sd + FSL_SRDSCR1_OFFS, tmp);
+		/* CR 2 */
+		tmp = in_be32(sd + FSL_SRDSCR2_OFFS);
+		tmp &= ~FSL_SRDSCR2_EICA_MASK;
+		tmp |= FSL_SRDSCR2_EICA_SATA;
+		out_be32(sd + FSL_SRDSCR2_OFFS, tmp);
+		/* CR 3 */
+		tmp = in_be32(sd + FSL_SRDSCR3_OFFS);
+		tmp &= ~FSL_SRDSCR3_LANEA_MASK;
+		tmp |= FSL_SRDSCR3_LANEA_SATA;
+		out_be32(sd + FSL_SRDSCR3_OFFS, tmp);
+		break;
+	case 4: /* Lane A - eTSEC1 SGMII, Lane E - eTSEC3 SGMII */
+		/* CR 0 */
+		tmp = in_be32(sd + FSL_SRDSCR0_OFFS);
+		tmp &= ~FSL_SRDSCR0_TXEQA_MASK;
+		tmp |= FSL_SRDSCR0_TXEQA_SGMII;
+		tmp &= ~FSL_SRDSCR0_TXEQE_MASK;
+		tmp |= FSL_SRDSCR0_TXEQE_SGMII;
+		out_be32(sd + FSL_SRDSCR0_OFFS, tmp);
+		/* CR 1 */
+		tmp = in_be32(sd + FSL_SRDSCR1_OFFS);
+		tmp &= ~FSL_SRDSCR1_LANEA_MASK;
+		tmp &= ~FSL_SRDSCR1_LANEE_MASK;
+		out_be32(sd + FSL_SRDSCR1_OFFS, tmp);
+		/* CR 2 */
+		tmp = in_be32(sd + FSL_SRDSCR2_OFFS);
+		tmp &= ~FSL_SRDSCR2_EICA_MASK;
+		tmp |= FSL_SRDSCR2_EICA_SGMII;
+		tmp &= ~FSL_SRDSCR2_EICE_MASK;
+		tmp |= FSL_SRDSCR2_EICE_SGMII;
+		out_be32(sd + FSL_SRDSCR2_OFFS, tmp);
+		/* CR 3 */
+		tmp = in_be32(sd + FSL_SRDSCR3_OFFS);
+		tmp &= ~FSL_SRDSCR3_LANEA_MASK;
+		tmp |= FSL_SRDSCR3_LANEA_SGMII;
+		tmp &= ~FSL_SRDSCR3_LANEE_MASK;
+		tmp |= FSL_SRDSCR3_LANEE_SGMII;
+		out_be32(sd + FSL_SRDSCR3_OFFS, tmp);
+		break;
+	case 6: /* Lane A - eTSEC1 SGMII, Lane E - disabled */
+		/* CR 0 */
+		tmp = in_be32(sd + FSL_SRDSCR0_OFFS);
+		tmp &= ~FSL_SRDSCR0_TXEQA_MASK;
+		tmp |= FSL_SRDSCR0_TXEQA_SGMII;
+		out_be32(sd + FSL_SRDSCR0_OFFS, tmp);
+		/* CR 1 */
+		tmp = in_be32(sd + FSL_SRDSCR1_OFFS);
+		tmp &= ~FSL_SRDSCR1_LANEE_MASK;
+		tmp |= FSL_SRDSCR1_LANEE_OFF;
+		out_be32(sd + FSL_SRDSCR1_OFFS, tmp);
+		/* CR 2 */
+		tmp = in_be32(sd + FSL_SRDSCR2_OFFS);
+		tmp &= ~FSL_SRDSCR2_EICA_MASK;
+		tmp |= FSL_SRDSCR2_EICA_SGMII;
+		out_be32(sd + FSL_SRDSCR2_OFFS, tmp);
+		/* CR 3 */
+		tmp = in_be32(sd + FSL_SRDSCR3_OFFS);
+		tmp &= ~FSL_SRDSCR3_LANEA_MASK;
+		tmp |= FSL_SRDSCR3_LANEA_SGMII;
+		out_be32(sd + FSL_SRDSCR3_OFFS, tmp);
+		break;
+	case 7: /* Lane A - disabled, Lane E - disabled */
+		/* CR 1 */
+		tmp = in_be32(sd + FSL_SRDSCR1_OFFS);
+		tmp &= ~FSL_SRDSCR1_LANEA_MASK;
+		tmp |= FSL_SRDSCR1_LANEA_OFF;
+		tmp &= ~FSL_SRDSCR1_LANEE_MASK;
+		tmp |= FSL_SRDSCR1_LANEE_OFF;
+		out_be32(sd + FSL_SRDSCR1_OFFS, tmp);
+		break;
+	default:
+		break;
+	}
+}
diff --git a/cpu/mpc85xx/pci.c b/cpu/mpc85xx/pci.c
index a5060cd..fdc4c83 100644
--- a/cpu/mpc85xx/pci.c
+++ b/cpu/mpc85xx/pci.c
@@ -29,7 +29,7 @@
 #include <asm/cpm_85xx.h>
 #include <pci.h>
 
-#if defined(CONFIG_PCI)
+#if defined(CONFIG_PCI) && !defined(CONFIG_FSL_PCI_INIT)
 
 static struct pci_controller *pci_hose;
 
diff --git a/cpu/mpc85xx/spd_sdram.c b/cpu/mpc85xx/spd_sdram.c
deleted file mode 100644
index 8e321eb..0000000
--- a/cpu/mpc85xx/spd_sdram.c
+++ /dev/null
@@ -1,1154 +0,0 @@
-/*
- * Copyright 2004, 2007 Freescale Semiconductor.
- * (C) Copyright 2003 Motorola Inc.
- * Xianghua Xiao (X.Xiao@motorola.com)
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <i2c.h>
-#include <spd.h>
-#include <asm/mmu.h>
-#include <asm/fsl_law.h>
-
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-extern void dma_init(void);
-extern uint dma_check(void);
-extern int dma_xfer(void *dest, uint count, void *src);
-#endif
-
-#ifdef CONFIG_SPD_EEPROM
-
-#ifndef	CFG_READ_SPD
-#define CFG_READ_SPD	i2c_read
-#endif
-
-static unsigned int setup_laws_and_tlbs(unsigned int memsize);
-
-
-/*
- * Convert picoseconds into clock cycles (rounding up if needed).
- */
-
-int
-picos_to_clk(int picos)
-{
-	int clks;
-
-	clks = picos / (2000000000 / (get_ddr_freq(0) / 1000));
-	if (picos % (2000000000 / (get_ddr_freq(0) / 1000)) != 0) {
-		clks++;
-	}
-
-	return clks;
-}
-
-
-/*
- * Calculate the Density of each Physical Rank.
- * Returned size is in bytes.
- *
- * Study these table from Byte 31 of JEDEC SPD Spec.
- *
- *		DDR I	DDR II
- *	Bit	Size	Size
- *	---	-----	------
- *	7 high	512MB	512MB
- *	6	256MB	256MB
- *	5	128MB	128MB
- *	4	 64MB	 16GB
- *	3	 32MB	  8GB
- *	2	 16MB	  4GB
- *	1	  2GB	  2GB
- *	0 low	  1GB	  1GB
- *
- * Reorder Table to be linear by stripping the bottom
- * 2 or 5 bits off and shifting them up to the top.
- */
-
-unsigned int
-compute_banksize(unsigned int mem_type, unsigned char row_dens)
-{
-	unsigned int bsize;
-
-	if (mem_type == SPD_MEMTYPE_DDR) {
-		/* Bottom 2 bits up to the top. */
-		bsize = ((row_dens >> 2) | ((row_dens & 3) << 6)) << 24;
-		debug("DDR: DDR I rank density = 0x%08x\n", bsize);
-	} else {
-		/* Bottom 5 bits up to the top. */
-		bsize = ((row_dens >> 5) | ((row_dens & 31) << 3)) << 27;
-		debug("DDR: DDR II rank density = 0x%08x\n", bsize);
-	}
-	return bsize;
-}
-
-
-/*
- * Convert a two-nibble BCD value into a cycle time.
- * While the spec calls for nano-seconds, picos are returned.
- *
- * This implements the tables for bytes 9, 23 and 25 for both
- * DDR I and II.  No allowance for distinguishing the invalid
- * fields absent for DDR I yet present in DDR II is made.
- * (That is, cycle times of .25, .33, .66 and .75 ns are
- * allowed for both DDR II and I.)
- */
-
-unsigned int
-convert_bcd_tenths_to_cycle_time_ps(unsigned int spd_val)
-{
-	/*
-	 * Table look up the lower nibble, allow DDR I & II.
-	 */
-	unsigned int tenths_ps[16] = {
-		0,
-		100,
-		200,
-		300,
-		400,
-		500,
-		600,
-		700,
-		800,
-		900,
-		250,
-		330,
-		660,
-		750,
-		0,	/* undefined */
-		0	/* undefined */
-	};
-
-	unsigned int whole_ns = (spd_val & 0xF0) >> 4;
-	unsigned int tenth_ns = spd_val & 0x0F;
-	unsigned int ps = whole_ns * 1000 + tenths_ps[tenth_ns];
-
-	return ps;
-}
-
-
-/*
- * Determine Refresh Rate.  Ignore self refresh bit on DDR I.
- * Table from SPD Spec, Byte 12, converted to picoseconds and
- * filled in with "default" normal values.
- */
-unsigned int determine_refresh_rate(unsigned int spd_refresh)
-{
-	unsigned int refresh_time_ns[8] = {
-		15625000,	/* 0 Normal    1.00x */
-		3900000,	/* 1 Reduced    .25x */
-		7800000,	/* 2 Extended   .50x */
-		31300000,	/* 3 Extended  2.00x */
-		62500000,	/* 4 Extended  4.00x */
-		125000000,	/* 5 Extended  8.00x */
-		15625000,	/* 6 Normal    1.00x  filler */
-		15625000,	/* 7 Normal    1.00x  filler */
-	};
-
-	return picos_to_clk(refresh_time_ns[spd_refresh & 0x7]);
-}
-
-
-long int
-spd_sdram(void)
-{
-	volatile ccsr_ddr_t *ddr = (void *)(CFG_MPC85xx_DDR_ADDR);
-	spd_eeprom_t spd;
-	unsigned int n_ranks;
-	unsigned int rank_density;
-	unsigned int odt_rd_cfg, odt_wr_cfg, ba_bits;
-	unsigned int odt_cfg, mode_odt_enable;
-	unsigned int refresh_clk;
-#ifdef MPC85xx_DDR_SDRAM_CLK_CNTL
-	unsigned char clk_adjust;
-#endif
-	unsigned int dqs_cfg;
-	unsigned char twr_clk, twtr_clk, twr_auto_clk;
-	unsigned int tCKmin_ps, tCKmax_ps;
-	unsigned int max_data_rate, effective_data_rate;
-	unsigned int busfreq;
-	unsigned sdram_cfg;
-	unsigned int memsize = 0;
-	unsigned char caslat, caslat_ctrl;
-	unsigned int trfc, trfc_clk, trfc_low, trfc_high;
-	unsigned int trcd_clk;
-	unsigned int trtp_clk;
-	unsigned char cke_min_clk;
-	unsigned char add_lat;
-	unsigned char wr_lat;
-	unsigned char wr_data_delay;
-	unsigned char four_act;
-	unsigned char cpo;
-	unsigned char burst_len;
-	unsigned int mode_caslat;
-	unsigned char sdram_type;
-	unsigned char d_init;
-	unsigned int bnds;
-
-	/*
-	 * Skip configuration if already configured.
-	 * memsize is determined from last configured chip select.
-	 */
-	if (ddr->cs0_config & 0x80000000) {
-		debug(" cs0 already configured, bnds=%x\n",ddr->cs0_bnds);
-		bnds = 0xfff & ddr->cs0_bnds;
-		if (bnds < 0xff) { /* do not add if at top of 4G */
-			memsize = (bnds + 1) << 4;
-		}
-	}
-	if (ddr->cs1_config & 0x80000000) {
-		debug(" cs1 already configured, bnds=%x\n",ddr->cs1_bnds);
-		bnds = 0xfff & ddr->cs1_bnds;
-		if (bnds < 0xff) { /* do not add if at top of 4G */
-			memsize = (bnds + 1) << 4; /* assume ordered bnds */
-		}
-	}
-	if (ddr->cs2_config & 0x80000000) {
-		debug(" cs2 already configured, bnds=%x\n",ddr->cs2_bnds);
-		bnds = 0xfff & ddr->cs2_bnds;
-		if (bnds < 0xff) { /* do not add if at top of 4G */
-			memsize = (bnds + 1) << 4;
-		}
-	}
-	if (ddr->cs3_config & 0x80000000) {
-		debug(" cs3 already configured, bnds=%x\n",ddr->cs3_bnds);
-		bnds = 0xfff & ddr->cs3_bnds;
-		if (bnds < 0xff) { /* do not add if at top of 4G */
-			memsize = (bnds + 1) << 4;
-		}
-	}
-
-	if (memsize) {
-		printf("       Reusing current %dMB configuration\n",memsize);
-		memsize = setup_laws_and_tlbs(memsize);
-		return memsize << 20;
-	}
-
-	/*
-	 * Read SPD information.
-	 */
-	CFG_READ_SPD(SPD_EEPROM_ADDRESS, 0, 1, (uchar *) &spd, sizeof(spd));
-
-	/*
-	 * Check for supported memory module types.
-	 */
-	if (spd.mem_type != SPD_MEMTYPE_DDR &&
-	    spd.mem_type != SPD_MEMTYPE_DDR2) {
-		printf("Unable to locate DDR I or DDR II module.\n"
-		       "    Fundamental memory type is 0x%0x\n",
-		       spd.mem_type);
-		return 0;
-	}
-
-	/*
-	 * These test gloss over DDR I and II differences in interpretation
-	 * of bytes 3 and 4, but irrelevantly.  Multiple asymmetric banks
-	 * are not supported on DDR I; and not encoded on DDR II.
-	 *
-	 * Also note that the 8548 controller can support:
-	 *    12 <= nrow <= 16
-	 * and
-	 *     8 <= ncol <= 11 (still, for DDR)
-	 *     6 <= ncol <=  9 (for FCRAM)
-	 */
-	if (spd.nrow_addr < 12 || spd.nrow_addr > 14) {
-		printf("DDR: Unsupported number of Row Addr lines: %d.\n",
-		       spd.nrow_addr);
-		return 0;
-	}
-	if (spd.ncol_addr < 8 || spd.ncol_addr > 11) {
-		printf("DDR: Unsupported number of Column Addr lines: %d.\n",
-		       spd.ncol_addr);
-		return 0;
-	}
-
-	/*
-	 * Determine the number of physical banks controlled by
-	 * different Chip Select signals.  This is not quite the
-	 * same as the number of DIMM modules on the board.  Feh.
-	 */
-	if (spd.mem_type == SPD_MEMTYPE_DDR) {
-		n_ranks = spd.nrows;
-	} else {
-		n_ranks = (spd.nrows & 0x7) + 1;
-	}
-
-	debug("DDR: number of ranks = %d\n", n_ranks);
-
-	if (n_ranks > 2) {
-		printf("DDR: Only 2 chip selects are supported: %d\n",
-		       n_ranks);
-		return 0;
-	}
-
-#ifdef CONFIG_MPC8548
-	/*
-	 * Adjust DDR II IO voltage biasing.
-	 * Only 8548 rev 1 needs the fix
-	 */
-	if ((SVR_SOC_VER(get_svr()) == SVR_8548_E) &&
-			(SVR_MJREV(get_svr()) == 1) &&
-			(spd.mem_type == SPD_MEMTYPE_DDR2)) {
-		volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
-		gur->ddrioovcr = (0x80000000	/* Enable */
-				  | 0x10000000);/* VSEL to 1.8V */
-	}
-#endif
-
-	/*
-	 * Determine the size of each Rank in bytes.
-	 */
-	rank_density = compute_banksize(spd.mem_type, spd.row_dens);
-
-
-	/*
-	 * Eg: Bounds: 0x0000_0000 to 0x0f000_0000	first 256 Meg
-	 */
-	ddr->cs0_bnds = (rank_density >> 24) - 1;
-
-	/*
-	 * ODT configuration recommendation from DDR Controller Chapter.
-	 */
-	odt_rd_cfg = 0;			/* Never assert ODT */
-	odt_wr_cfg = 0;			/* Never assert ODT */
-	if (spd.mem_type == SPD_MEMTYPE_DDR2) {
-		odt_wr_cfg = 1;		/* Assert ODT on writes to CS0 */
-#if 0
-		/* FIXME: How to determine the number of dimm modules? */
-		if (n_dimm_modules == 2) {
-			odt_rd_cfg = 1;	/* Assert ODT on reads to CS0 */
-		}
-#endif
-	}
-
-	ba_bits = 0;
-	if (spd.nbanks == 0x8)
-		ba_bits = 1;
-
-	ddr->cs0_config = ( 1 << 31
-			    | (odt_rd_cfg << 20)
-			    | (odt_wr_cfg << 16)
-			    | (ba_bits << 14)
-			    | (spd.nrow_addr - 12) << 8
-			    | (spd.ncol_addr - 8) );
-	debug("\n");
-	debug("DDR: cs0_bnds   = 0x%08x\n", ddr->cs0_bnds);
-	debug("DDR: cs0_config = 0x%08x\n", ddr->cs0_config);
-
-	if (n_ranks == 2) {
-		/*
-		 * Eg: Bounds: 0x0f00_0000 to 0x1e0000_0000, second 256 Meg
-		 */
-		ddr->cs1_bnds = ( (rank_density >> 8)
-				  | ((rank_density >> (24 - 1)) - 1) );
-		ddr->cs1_config = ( 1<<31
-				    | (odt_rd_cfg << 20)
-				    | (odt_wr_cfg << 16)
-				    | (spd.nrow_addr - 12) << 8
-				    | (spd.ncol_addr - 8) );
-		debug("DDR: cs1_bnds   = 0x%08x\n", ddr->cs1_bnds);
-		debug("DDR: cs1_config = 0x%08x\n", ddr->cs1_config);
-	}
-
-
-	/*
-	 * Find the largest CAS by locating the highest 1 bit
-	 * in the spd.cas_lat field.  Translate it to a DDR
-	 * controller field value:
-	 *
-	 *	CAS Lat	DDR I	DDR II	Ctrl
-	 *	Clocks	SPD Bit	SPD Bit	Value
-	 *	-------	-------	-------	-----
-	 *	1.0	0		0001
-	 *	1.5	1		0010
-	 *	2.0	2	2	0011
-	 *	2.5	3		0100
-	 *	3.0	4	3	0101
-	 *	3.5	5		0110
-	 *	4.0		4	0111
-	 *	4.5			1000
-	 *	5.0		5	1001
-	 */
-	caslat = __ilog2(spd.cas_lat);
-	if ((spd.mem_type == SPD_MEMTYPE_DDR)
-	    && (caslat > 5)) {
-		printf("DDR I: Invalid SPD CAS Latency: 0x%x.\n", spd.cas_lat);
-		return 0;
-
-	} else if (spd.mem_type == SPD_MEMTYPE_DDR2
-		   && (caslat < 2 || caslat > 5)) {
-		printf("DDR II: Invalid SPD CAS Latency: 0x%x.\n",
-		       spd.cas_lat);
-		return 0;
-	}
-	debug("DDR: caslat SPD bit is %d\n", caslat);
-
-	/*
-	 * Calculate the Maximum Data Rate based on the Minimum Cycle time.
-	 * The SPD clk_cycle field (tCKmin) is measured in tenths of
-	 * nanoseconds and represented as BCD.
-	 */
-	tCKmin_ps = convert_bcd_tenths_to_cycle_time_ps(spd.clk_cycle);
-	debug("DDR: tCKmin = %d ps\n", tCKmin_ps);
-
-	/*
-	 * Double-data rate, scaled 1000 to picoseconds, and back down to MHz.
-	 */
-	max_data_rate = 2 * 1000 * 1000 / tCKmin_ps;
-	debug("DDR: Module max data rate = %d Mhz\n", max_data_rate);
-
-
-	/*
-	 * Adjust the CAS Latency to allow for bus speeds that
-	 * are slower than the DDR module.
-	 */
-	busfreq = get_ddr_freq(0) / 1000000;	/* MHz */
-
-	effective_data_rate = max_data_rate;
-	if (busfreq < 90) {
-		/* DDR rate out-of-range */
-		puts("DDR: platform frequency is not fit for DDR rate\n");
-		return 0;
-
-	} else if (90 <= busfreq && busfreq < 230 && max_data_rate >= 230) {
-		/*
-		 * busfreq 90~230 range, treated as DDR 200.
-		 */
-		effective_data_rate = 200;
-		if (spd.clk_cycle3 == 0xa0)	/* 10 ns */
-			caslat -= 2;
-		else if (spd.clk_cycle2 == 0xa0)
-			caslat--;
-
-	} else if (230 <= busfreq && busfreq < 280 && max_data_rate >= 280) {
-		/*
-		 * busfreq 230~280 range, treated as DDR 266.
-		 */
-		effective_data_rate = 266;
-		if (spd.clk_cycle3 == 0x75)	/* 7.5 ns */
-			caslat -= 2;
-		else if (spd.clk_cycle2 == 0x75)
-			caslat--;
-
-	} else if (280 <= busfreq && busfreq < 350 && max_data_rate >= 350) {
-		/*
-		 * busfreq 280~350 range, treated as DDR 333.
-		 */
-		effective_data_rate = 333;
-		if (spd.clk_cycle3 == 0x60)	/* 6.0 ns */
-			caslat -= 2;
-		else if (spd.clk_cycle2 == 0x60)
-			caslat--;
-
-	} else if (350 <= busfreq && busfreq < 460 && max_data_rate >= 460) {
-		/*
-		 * busfreq 350~460 range, treated as DDR 400.
-		 */
-		effective_data_rate = 400;
-		if (spd.clk_cycle3 == 0x50)	/* 5.0 ns */
-			caslat -= 2;
-		else if (spd.clk_cycle2 == 0x50)
-			caslat--;
-
-	} else if (460 <= busfreq && busfreq < 560 && max_data_rate >= 560) {
-		/*
-		 * busfreq 460~560 range, treated as DDR 533.
-		 */
-		effective_data_rate = 533;
-		if (spd.clk_cycle3 == 0x3D)	/* 3.75 ns */
-			caslat -= 2;
-		else if (spd.clk_cycle2 == 0x3D)
-			caslat--;
-
-	} else if (560 <= busfreq && busfreq < 700 && max_data_rate >= 700) {
-		/*
-		 * busfreq 560~700 range, treated as DDR 667.
-		 */
-		effective_data_rate = 667;
-		if (spd.clk_cycle3 == 0x30)	/* 3.0 ns */
-			caslat -= 2;
-		else if (spd.clk_cycle2 == 0x30)
-			caslat--;
-
-	} else if (700 <= busfreq) {
-		/*
-		 * DDR rate out-of-range
-		 */
-		printf("DDR: Bus freq %d MHz is not fit for DDR rate %d MHz\n",
-		     busfreq, max_data_rate);
-		return 0;
-	}
-
-
-	/*
-	 * Convert caslat clocks to DDR controller value.
-	 * Force caslat_ctrl to be DDR Controller field-sized.
-	 */
-	if (spd.mem_type == SPD_MEMTYPE_DDR) {
-		caslat_ctrl = (caslat + 1) & 0x07;
-	} else {
-		caslat_ctrl =  (2 * caslat - 1) & 0x0f;
-	}
-
-	debug("DDR: effective data rate is %d MHz\n", effective_data_rate);
-	debug("DDR: caslat SPD bit is %d, controller field is 0x%x\n",
-	      caslat, caslat_ctrl);
-
-	/*
-	 * Timing Config 0.
-	 * Avoid writing for DDR I.  The new PQ38 DDR controller
-	 * dreams up non-zero default values to be backwards compatible.
-	 */
-	if (spd.mem_type == SPD_MEMTYPE_DDR2) {
-		unsigned char taxpd_clk = 8;		/* By the book. */
-		unsigned char tmrd_clk = 2;		/* By the book. */
-		unsigned char act_pd_exit = 2;		/* Empirical? */
-		unsigned char pre_pd_exit = 6;		/* Empirical? */
-
-		ddr->timing_cfg_0 = (0
-			| ((act_pd_exit & 0x7) << 20)	/* ACT_PD_EXIT */
-			| ((pre_pd_exit & 0x7) << 16)	/* PRE_PD_EXIT */
-			| ((taxpd_clk & 0xf) << 8)	/* ODT_PD_EXIT */
-			| ((tmrd_clk & 0xf) << 0)	/* MRS_CYC */
-			);
-#if 0
-		ddr->timing_cfg_0 |= 0xaa000000;	/* extra cycles */
-#endif
-		debug("DDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0);
-
-	} else {
-#if 0
-		/*
-		 * Force extra cycles with 0xaa bits.
-		 * Incidentally supply the dreamt-up backwards compat value!
-		 */
-		ddr->timing_cfg_0 = 0x00110105;	/* backwards compat value */
-		ddr->timing_cfg_0 |= 0xaa000000;	/* extra cycles */
-		debug("DDR: HACK timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0);
-#endif
-	}
-
-
-	/*
-	 * Some Timing Config 1 values now.
-	 * Sneak Extended Refresh Recovery in here too.
-	 */
-
-	/*
-	 * For DDR I, WRREC(Twr) and WRTORD(Twtr) are not in SPD,
-	 * use conservative value.
-	 * For DDR II, they are bytes 36 and 37, in quarter nanos.
-	 */
-
-	if (spd.mem_type == SPD_MEMTYPE_DDR) {
-		twr_clk = 3;	/* Clocks */
-		twtr_clk = 1;	/* Clocks */
-	} else {
-		twr_clk = picos_to_clk(spd.twr * 250);
-		twtr_clk = picos_to_clk(spd.twtr * 250);
-	}
-
-	/*
-	 * Calculate Trfc, in picos.
-	 * DDR I:  Byte 42 straight up in ns.
-	 * DDR II: Byte 40 and 42 swizzled some, in ns.
-	 */
-	if (spd.mem_type == SPD_MEMTYPE_DDR) {
-		trfc = spd.trfc * 1000;		/* up to ps */
-	} else {
-		unsigned int byte40_table_ps[8] = {
-			0,
-			250,
-			330,
-			500,
-			660,
-			750,
-			0,
-			0
-		};
-
-		trfc = (((spd.trctrfc_ext & 0x1) * 256) + spd.trfc) * 1000
-			+ byte40_table_ps[(spd.trctrfc_ext >> 1) & 0x7];
-	}
-	trfc_clk = picos_to_clk(trfc);
-
-	/*
-	 * Trcd, Byte 29, from quarter nanos to ps and clocks.
-	 */
-	trcd_clk = picos_to_clk(spd.trcd * 250) & 0x7;
-
-	/*
-	 * Convert trfc_clk to DDR controller fields.  DDR I should
-	 * fit in the REFREC field (16-19) of TIMING_CFG_1, but the
-	 * 8548 controller has an extended REFREC field of three bits.
-	 * The controller automatically adds 8 clocks to this value,
-	 * so preadjust it down 8 first before splitting it up.
-	 */
-	trfc_low = (trfc_clk - 8) & 0xf;
-	trfc_high = ((trfc_clk - 8) >> 4) & 0x3;
-
-	/*
-	 * Sneak in some Extended Refresh Recovery.
-	 */
-	ddr->timing_cfg_3 = (trfc_high << 16);
-	debug("DDR: timing_cfg_3 = 0x%08x\n", ddr->timing_cfg_3);
-
-	ddr->timing_cfg_1 =
-	    (0
-	     | ((picos_to_clk(spd.trp * 250) & 0x07) << 28)	/* PRETOACT */
-	     | ((picos_to_clk(spd.tras * 1000) & 0x0f ) << 24)	/* ACTTOPRE */
-	     | (trcd_clk << 20)					/* ACTTORW */
-	     | (caslat_ctrl << 16)				/* CASLAT */
-	     | (trfc_low << 12)					/* REFEC */
-	     | ((twr_clk & 0x07) << 8)				/* WRRREC */
-	     | ((picos_to_clk(spd.trrd * 250) & 0x07) << 4)	/* ACTTOACT */
-	     | ((twtr_clk & 0x07) << 0)				/* WRTORD */
-	     );
-
-	debug("DDR: timing_cfg_1  = 0x%08x\n", ddr->timing_cfg_1);
-
-
-	/*
-	 * Timing_Config_2
-	 * Was: 0x00000800;
-	 */
-
-	/*
-	 * Additive Latency
-	 * For DDR I, 0.
-	 * For DDR II, with ODT enabled, use "a value" less than ACTTORW,
-	 * which comes from Trcd, and also note that:
-	 *	add_lat + caslat must be >= 4
-	 */
-	add_lat = 0;
-	if (spd.mem_type == SPD_MEMTYPE_DDR2
-	    && (odt_wr_cfg || odt_rd_cfg)
-	    && (caslat < 4)) {
-		add_lat = 4 - caslat;
-		if (add_lat > trcd_clk) {
-			add_lat = trcd_clk - 1;
-		}
-	}
-
-	/*
-	 * Write Data Delay
-	 * Historically 0x2 == 4/8 clock delay.
-	 * Empirically, 0x3 == 6/8 clock delay is suggested for DDR I 266.
-	 */
-	wr_data_delay = 3;
-
-	/*
-	 * Write Latency
-	 * Read to Precharge
-	 * Minimum CKE Pulse Width.
-	 * Four Activate Window
-	 */
-	if (spd.mem_type == SPD_MEMTYPE_DDR) {
-		/*
-		 * This is a lie.  It should really be 1, but if it is
-		 * set to 1, bits overlap into the old controller's
-		 * otherwise unused ACSM field.  If we leave it 0, then
-		 * the HW will magically treat it as 1 for DDR 1.  Oh Yea.
-		 */
-		wr_lat = 0;
-
-		trtp_clk = 2;		/* By the book. */
-		cke_min_clk = 1;	/* By the book. */
-		four_act = 1;		/* By the book. */
-
-	} else {
-		wr_lat = caslat - 1;
-
-		/* Convert SPD value from quarter nanos to picos. */
-		trtp_clk = picos_to_clk(spd.trtp * 250);
-
-		cke_min_clk = 3;	/* By the book. */
-		four_act = picos_to_clk(37500);	/* By the book. 1k pages? */
-	}
-
-	/*
-	 * Empirically set ~MCAS-to-preamble override for DDR 2.
-	 * Your milage will vary.
-	 */
-	cpo = 0;
-	if (spd.mem_type == SPD_MEMTYPE_DDR2) {
-		if (effective_data_rate <= 333) {
-			cpo = 0x7;		/* READ_LAT + 5/4 */
-		} else {
-			cpo = 0x9;		/* READ_LAT + 7/4 */
-		}
-	}
-
-	ddr->timing_cfg_2 = (0
-		| ((add_lat & 0x7) << 28)		/* ADD_LAT */
-		| ((cpo & 0x1f) << 23)			/* CPO */
-		| ((wr_lat & 0x7) << 19)		/* WR_LAT */
-		| ((trtp_clk & 0x7) << 13)		/* RD_TO_PRE */
-		| ((wr_data_delay & 0x7) << 10)		/* WR_DATA_DELAY */
-		| ((cke_min_clk & 0x7) << 6)		/* CKE_PLS */
-		| ((four_act & 0x1f) << 0)		/* FOUR_ACT */
-		);
-
-	debug("DDR: timing_cfg_2 = 0x%08x\n", ddr->timing_cfg_2);
-
-
-	/*
-	 * Determine the Mode Register Set.
-	 *
-	 * This is nominally part specific, but it appears to be
-	 * consistent for all DDR I devices, and for all DDR II devices.
-	 *
-	 *     caslat must be programmed
-	 *     burst length is always 4
-	 *     burst type is sequential
-	 *
-	 * For DDR I:
-	 *     operating mode is "normal"
-	 *
-	 * For DDR II:
-	 *     other stuff
-	 */
-
-	mode_caslat = 0;
-
-	/*
-	 * Table lookup from DDR I or II Device Operation Specs.
-	 */
-	if (spd.mem_type == SPD_MEMTYPE_DDR) {
-		if (1 <= caslat && caslat <= 4) {
-			unsigned char mode_caslat_table[4] = {
-				0x5,	/* 1.5 clocks */
-				0x2,	/* 2.0 clocks */
-				0x6,	/* 2.5 clocks */
-				0x3	/* 3.0 clocks */
-			};
-			mode_caslat = mode_caslat_table[caslat - 1];
-		} else {
-			puts("DDR I: Only CAS Latencies of 1.5, 2.0, "
-			     "2.5 and 3.0 clocks are supported.\n");
-			return 0;
-		}
-
-	} else {
-		if (2 <= caslat && caslat <= 5) {
-			mode_caslat = caslat;
-		} else {
-			puts("DDR II: Only CAS Latencies of 2.0, 3.0, "
-			     "4.0 and 5.0 clocks are supported.\n");
-			return 0;
-		}
-	}
-
-	/*
-	 * Encoded Burst Lenght of 4.
-	 */
-	burst_len = 2;			/* Fiat. */
-
-	if (spd.mem_type == SPD_MEMTYPE_DDR) {
-		twr_auto_clk = 0;	/* Historical */
-	} else {
-		/*
-		 * Determine tCK max in picos.  Grab tWR and convert to picos.
-		 * Auto-precharge write recovery is:
-		 *	WR = roundup(tWR_ns/tCKmax_ns).
-		 *
-		 * Ponder: Is twr_auto_clk different than twr_clk?
-		 */
-		tCKmax_ps = convert_bcd_tenths_to_cycle_time_ps(spd.tckmax);
-		twr_auto_clk = (spd.twr * 250 + tCKmax_ps - 1) / tCKmax_ps;
-	}
-
-
-	/*
-	 * Mode Reg in bits 16 ~ 31,
-	 * Extended Mode Reg 1 in bits 0 ~ 15.
-	 */
-	mode_odt_enable = 0x0;			/* Default disabled */
-	if (odt_wr_cfg || odt_rd_cfg) {
-		/*
-		 * Bits 6 and 2 in Extended MRS(1)
-		 * Bit 2 == 0x04 == 75 Ohm, with 2 DIMM modules.
-		 * Bit 6 == 0x40 == 150 Ohm, with 1 DIMM module.
-		 */
-		mode_odt_enable = 0x40;		/* 150 Ohm */
-	}
-
-	ddr->sdram_mode =
-		(0
-		 | (add_lat << (16 + 3))	/* Additive Latency in EMRS1 */
-		 | (mode_odt_enable << 16)	/* ODT Enable in EMRS1 */
-		 | (twr_auto_clk << 9)		/* Write Recovery Autopre */
-		 | (mode_caslat << 4)		/* caslat */
-		 | (burst_len << 0)		/* Burst length */
-		 );
-
-	debug("DDR: sdram_mode   = 0x%08x\n", ddr->sdram_mode);
-
-
-	/*
-	 * Clear EMRS2 and EMRS3.
-	 */
-	ddr->sdram_mode_2 = 0;
-	debug("DDR: sdram_mode_2 = 0x%08x\n", ddr->sdram_mode_2);
-
-	/*
-	 * Determine Refresh Rate.
-	 */
-	refresh_clk = determine_refresh_rate(spd.refresh & 0x7);
-
-	/*
-	 * Set BSTOPRE to 0x100 for page mode
-	 * If auto-charge is used, set BSTOPRE = 0
-	 */
-	ddr->sdram_interval =
-	    (0
-	     | (refresh_clk & 0x3fff) << 16
-	     | 0x100
-	     );
-	debug("DDR: sdram_interval = 0x%08x\n", ddr->sdram_interval);
-
-	/*
-	 * Is this an ECC DDR chip?
-	 * But don't mess with it if the DDR controller will init mem.
-	 */
-#ifdef CONFIG_DDR_ECC
-	if (spd.config == 0x02) {
-#ifndef CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-		ddr->err_disable = 0x0000000d;
-#endif
-		ddr->err_sbe = 0x00ff0000;
-	}
-
-	debug("DDR: err_disable = 0x%08x\n", ddr->err_disable);
-	debug("DDR: err_sbe = 0x%08x\n", ddr->err_sbe);
-#endif /* CONFIG_DDR_ECC */
-
-	asm("sync;isync;msync");
-	udelay(500);
-
-	/*
-	 * SDRAM Cfg 2
-	 */
-
-	/*
-	 * When ODT is enabled, Chap 9 suggests asserting ODT to
-	 * internal IOs only during reads.
-	 */
-	odt_cfg = 0;
-	if (odt_rd_cfg | odt_wr_cfg) {
-		odt_cfg = 0x2;		/* ODT to IOs during reads */
-	}
-
-	/*
-	 * Try to use differential DQS with DDR II.
-	 */
-	if (spd.mem_type == SPD_MEMTYPE_DDR) {
-		dqs_cfg = 0;		/* No Differential DQS for DDR I */
-	} else {
-		dqs_cfg = 0x1;		/* Differential DQS for DDR II */
-	}
-
-#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-	/*
-	 * Use the DDR controller to auto initialize memory.
-	 */
-	d_init = 1;
-	ddr->sdram_data_init = CONFIG_MEM_INIT_VALUE;
-	debug("DDR: ddr_data_init = 0x%08x\n", ddr->sdram_data_init);
-#else
-	/*
-	 * Memory will be initialized via DMA, or not at all.
-	 */
-	d_init = 0;
-#endif
-
-	ddr->sdram_cfg_2 = (0
-			    | (dqs_cfg << 26)	/* Differential DQS */
-			    | (odt_cfg << 21)	/* ODT */
-			    | (d_init << 4)	/* D_INIT auto init DDR */
-			    );
-
-	debug("DDR: sdram_cfg_2  = 0x%08x\n", ddr->sdram_cfg_2);
-
-
-#ifdef MPC85xx_DDR_SDRAM_CLK_CNTL
-	/*
-	 * Setup the clock control.
-	 * SDRAM_CLK_CNTL[0] = Source synchronous enable == 1
-	 * SDRAM_CLK_CNTL[5-7] = Clock Adjust
-	 *	0110	3/4 cycle late
-	 *	0111	7/8 cycle late
-	 */
-	if (spd.mem_type == SPD_MEMTYPE_DDR)
-		clk_adjust = 0x6;
-	else
-#ifdef CONFIG_MPC8568
-		/* Empirally setting clk_adjust */
-		clk_adjust = 0x6;
-#else
-		clk_adjust = 0x7;
-#endif
-
-	ddr->sdram_clk_cntl = (0
-			       | 0x80000000
-			       | (clk_adjust << 23)
-			       );
-	debug("DDR: sdram_clk_cntl = 0x%08x\n", ddr->sdram_clk_cntl);
-#endif
-
-	/*
-	 * Figure out the settings for the sdram_cfg register.
-	 * Build up the entire register in 'sdram_cfg' before writing
-	 * since the write into the register will actually enable the
-	 * memory controller; all settings must be done before enabling.
-	 *
-	 * sdram_cfg[0]   = 1 (ddr sdram logic enable)
-	 * sdram_cfg[1]   = 1 (self-refresh-enable)
-	 * sdram_cfg[5:7] = (SDRAM type = DDR SDRAM)
-	 *			010 DDR 1 SDRAM
-	 *			011 DDR 2 SDRAM
-	 */
-	sdram_type = (spd.mem_type == SPD_MEMTYPE_DDR) ? 2 : 3;
-	sdram_cfg = (0
-		     | (1 << 31)			/* Enable */
-		     | (1 << 30)			/* Self refresh */
-		     | (sdram_type << 24)		/* SDRAM type */
-		     );
-
-	/*
-	 * sdram_cfg[3] = RD_EN - registered DIMM enable
-	 *   A value of 0x26 indicates micron registered DIMMS (micron.com)
-	 */
-	if (spd.mem_type == SPD_MEMTYPE_DDR && spd.mod_attr == 0x26) {
-		sdram_cfg |= 0x10000000;		/* RD_EN */
-	}
-
-#if defined(CONFIG_DDR_ECC)
-	/*
-	 * If the user wanted ECC (enabled via sdram_cfg[2])
-	 */
-	if (spd.config == 0x02) {
-		sdram_cfg |= 0x20000000;		/* ECC_EN */
-	}
-#endif
-
-	/*
-	 * REV1 uses 1T timing.
-	 * REV2 may use 1T or 2T as configured by the user.
-	 */
-	{
-		uint pvr = get_pvr();
-
-		if (pvr != PVR_85xx_REV1) {
-#if defined(CONFIG_DDR_2T_TIMING)
-			/*
-			 * Enable 2T timing by setting sdram_cfg[16].
-			 */
-			sdram_cfg |= 0x8000;		/* 2T_EN */
-#endif
-		}
-	}
-
-	/*
-	 * 200 painful micro-seconds must elapse between
-	 * the DDR clock setup and the DDR config enable.
-	 */
-	udelay(200);
-
-	/*
-	 * Go!
-	 */
-	ddr->sdram_cfg = sdram_cfg;
-
-	asm("sync;isync;msync");
-	udelay(500);
-
-	debug("DDR: sdram_cfg   = 0x%08x\n", ddr->sdram_cfg);
-
-
-#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-	/*
-	 * Poll until memory is initialized.
-	 * 512 Meg at 400 might hit this 200 times or so.
-	 */
-	while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) {
-		udelay(1000);
-	}
-#endif
-
-
-	/*
-	 * Figure out memory size in Megabytes.
-	 */
-	memsize = n_ranks * rank_density / 0x100000;
-
-	/*
-	 * Establish Local Access Window and TLB mappings for DDR memory.
-	 */
-	memsize = setup_laws_and_tlbs(memsize);
-	if (memsize == 0) {
-		return 0;
-	}
-
-	return memsize * 1024 * 1024;
-}
-
-
-/*
- * Setup Local Access Window and TLB1 mappings for the requested
- * amount of memory.  Returns the amount of memory actually mapped
- * (usually the original request size), or 0 on error.
- */
-
-static unsigned int
-setup_laws_and_tlbs(unsigned int memsize)
-{
-	unsigned int tlb_size;
-	unsigned int law_size;
-	unsigned int ram_tlb_index;
-	unsigned int ram_tlb_address;
-
-	/*
-	 * Determine size of each TLB1 entry.
-	 */
-	switch (memsize) {
-	case 16:
-	case 32:
-		tlb_size = BOOKE_PAGESZ_16M;
-		break;
-	case 64:
-	case 128:
-		tlb_size = BOOKE_PAGESZ_64M;
-		break;
-	case 256:
-	case 512:
-		tlb_size = BOOKE_PAGESZ_256M;
-		break;
-	case 1024:
-	case 2048:
-		if (PVR_VER(get_pvr()) > PVR_VER(PVR_85xx))
-			tlb_size = BOOKE_PAGESZ_1G;
-		else
-			tlb_size = BOOKE_PAGESZ_256M;
-		break;
-	default:
-		puts("DDR: only 16M,32M,64M,128M,256M,512M,1G and 2G are supported.\n");
-
-		/*
-		 * The memory was not able to be mapped.
-		 * Default to a small size.
-		 */
-		tlb_size = BOOKE_PAGESZ_64M;
-		memsize=64;
-		break;
-	}
-
-	/*
-	 * Configure DDR TLB1 entries.
-	 * Starting at TLB1 8, use no more than 8 TLB1 entries.
-	 */
-	ram_tlb_index = 8;
-	ram_tlb_address = (unsigned int)CFG_DDR_SDRAM_BASE;
-	while (ram_tlb_address < (memsize * 1024 * 1024)
-	      && ram_tlb_index < 16) {
-		set_tlb(1, ram_tlb_address, ram_tlb_address,
-			MAS3_SX|MAS3_SW|MAS3_SR, 0,
-			0, ram_tlb_index, tlb_size, 1);
-
-		ram_tlb_address += (0x1000 << ((tlb_size - 1) * 2));
-		ram_tlb_index++;
-	}
-
-
-	/*
-	 * First supported LAW size is 16M, at LAWAR_SIZE_16M == 23.  Fnord.
-	 */
-	law_size = 19 + __ilog2(memsize);
-
-	/*
-	 * Set up LAWBAR for all of DDR.
-	 */
-
-#ifdef CONFIG_FSL_LAW
-	set_next_law(CFG_DDR_SDRAM_BASE, law_size, LAW_TRGT_IF_DDR);
-#endif
-
-	/*
-	 * Confirm that the requested amount of memory was mapped.
-	 */
-	return memsize;
-}
-
-#endif /* CONFIG_SPD_EEPROM */
-
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-
-/*
- * Initialize all of memory for ECC, then enable errors.
- */
-
-void
-ddr_enable_ecc(unsigned int dram_size)
-{
-	uint *p = 0;
-	uint i = 0;
-	volatile ccsr_ddr_t *ddr= (void *)(CFG_MPC85xx_DDR_ADDR);
-
-	dma_init();
-
-	for (*p = 0; p < (uint *)(8 * 1024); p++) {
-		if (((unsigned int)p & 0x1f) == 0) {
-			ppcDcbz((unsigned long) p);
-		}
-		*p = (unsigned int)CONFIG_MEM_INIT_VALUE;
-		if (((unsigned int)p & 0x1c) == 0x1c) {
-			ppcDcbf((unsigned long) p);
-		}
-	}
-
-	dma_xfer((uint *)0x002000, 0x002000, (uint *)0); /* 8K */
-	dma_xfer((uint *)0x004000, 0x004000, (uint *)0); /* 16K */
-	dma_xfer((uint *)0x008000, 0x008000, (uint *)0); /* 32K */
-	dma_xfer((uint *)0x010000, 0x010000, (uint *)0); /* 64K */
-	dma_xfer((uint *)0x020000, 0x020000, (uint *)0); /* 128k */
-	dma_xfer((uint *)0x040000, 0x040000, (uint *)0); /* 256k */
-	dma_xfer((uint *)0x080000, 0x080000, (uint *)0); /* 512k */
-	dma_xfer((uint *)0x100000, 0x100000, (uint *)0); /* 1M */
-	dma_xfer((uint *)0x200000, 0x200000, (uint *)0); /* 2M */
-	dma_xfer((uint *)0x400000, 0x400000, (uint *)0); /* 4M */
-
-	for (i = 1; i < dram_size / 0x800000; i++) {
-		dma_xfer((uint *)(0x800000*i), 0x800000, (uint *)0);
-	}
-
-	/*
-	 * Enable errors for ECC.
-	 */
-	debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable);
-	ddr->err_disable = 0x00000000;
-	asm("sync;isync;msync");
-	debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable);
-}
-
-#endif	/* CONFIG_DDR_ECC  && ! CONFIG_ECC_INIT_VIA_DDRCONTROLLER */
diff --git a/cpu/mpc85xx/speed.c b/cpu/mpc85xx/speed.c
index 699441b4..1cda1e3 100644
--- a/cpu/mpc85xx/speed.c
+++ b/cpu/mpc85xx/speed.c
@@ -110,6 +110,10 @@
 #endif
 	gd->i2c2_clk = gd->i2c1_clk;
 
+#if defined(CONFIG_MPC8536)
+	gd->sdhc_clk = gd->bus_clk / 2;
+#endif
+
 #if defined(CONFIG_CPM2)
 	gd->vco_out = 2*sys_info.freqSystemBus;
 	gd->cpm_clk = gd->vco_out / 2;
diff --git a/cpu/mpc85xx/tlb.c b/cpu/mpc85xx/tlb.c
index 3d15d50..7ce7a14 100644
--- a/cpu/mpc85xx/tlb.c
+++ b/cpu/mpc85xx/tlb.c
@@ -90,3 +90,67 @@
 
 	return ;
 }
+
+unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg)
+{
+	unsigned int tlb_size;
+	unsigned int ram_tlb_index;
+	unsigned int ram_tlb_address;
+
+	/*
+	 * Determine size of each TLB1 entry.
+	 */
+	switch (memsize_in_meg) {
+	case 16:
+	case 32:
+		tlb_size = BOOKE_PAGESZ_16M;
+		break;
+	case 64:
+	case 128:
+		tlb_size = BOOKE_PAGESZ_64M;
+		break;
+	case 256:
+	case 512:
+		tlb_size = BOOKE_PAGESZ_256M;
+		break;
+	case 1024:
+	case 2048:
+		if (PVR_VER(get_pvr()) > PVR_VER(PVR_85xx))
+			tlb_size = BOOKE_PAGESZ_1G;
+		else
+			tlb_size = BOOKE_PAGESZ_256M;
+		break;
+	default:
+		puts("DDR: only 16M, 32M, 64M, 128M, 256M, 512M, 1G"
+			" and 2G are supported.\n");
+
+		/*
+		 * The memory was not able to be mapped.
+		 * Default to a small size.
+		 */
+		tlb_size = BOOKE_PAGESZ_64M;
+		memsize_in_meg = 64;
+		break;
+	}
+
+	/*
+	 * Configure DDR TLB1 entries.
+	 * Starting at TLB1 8, use no more than 8 TLB1 entries.
+	 */
+	ram_tlb_index = 8;
+	ram_tlb_address = (unsigned int)CFG_DDR_SDRAM_BASE;
+	while (ram_tlb_address < (memsize_in_meg * 1024 * 1024)
+	      && ram_tlb_index < 16) {
+		set_tlb(1, ram_tlb_address, ram_tlb_address,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, ram_tlb_index, tlb_size, 1);
+
+		ram_tlb_address += (0x1000 << ((tlb_size - 1) * 2));
+		ram_tlb_index++;
+	}
+
+	/*
+	 * Confirm that the requested amount of memory was mapped.
+	 */
+	return memsize_in_meg;
+}
diff --git a/drivers/misc/fsl_law.c b/drivers/misc/fsl_law.c
index e4e5c31..2e94614 100644
--- a/drivers/misc/fsl_law.c
+++ b/drivers/misc/fsl_law.c
@@ -38,7 +38,7 @@
       defined(CONFIG_MPC8568) || \
       defined(CONFIG_MPC8641) || defined(CONFIG_MPC8610)
 #define FSL_HW_NUM_LAWS 10
-#elif defined(CONFIG_MPC8572)
+#elif defined(CONFIG_MPC8536) || defined(CONFIG_MPC8572)
 #define FSL_HW_NUM_LAWS 12
 #else
 #error FSL_HW_NUM_LAWS not defined for this platform
diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h
index be2ce24..c09b07d 100644
--- a/include/asm-ppc/global_data.h
+++ b/include/asm-ppc/global_data.h
@@ -70,9 +70,6 @@
 #if defined(CONFIG_MPC8315)
 	u32 tdm_clk;
 #endif
-#if defined(CONFIG_MPC837X)
-	u32 sdhc_clk;
-#endif
 	u32 core_clk;
 	u32 enc_clk;
 	u32 lbiu_clk;
@@ -89,6 +86,9 @@
 	u32  mem_sec_clk;
 #endif /* CONFIG_MPC8360 */
 #endif
+#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8536)
+	u32 sdhc_clk;
+#endif
 #if defined(CONFIG_MPC83XX) || defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx)
 	u32 i2c1_clk;
 	u32 i2c2_clk;
diff --git a/include/asm-ppc/immap_85xx.h b/include/asm-ppc/immap_85xx.h
index 113ba48..559d6ea 100644
--- a/include/asm-ppc/immap_85xx.h
+++ b/include/asm-ppc/immap_85xx.h
@@ -1560,6 +1560,7 @@
 #define MPC85xx_PORDEVSR_SGMII2_DIS	0x10000000
 #define MPC85xx_PORDEVSR_SGMII3_DIS	0x08000000
 #define MPC85xx_PORDEVSR_SGMII4_DIS	0x04000000
+#define MPC85xx_PORDEVSR_SRDS2_IO_SEL   0x38000000
 #define MPC85xx_PORDEVSR_IO_SEL		0x00380000
 #define MPC85xx_PORDEVSR_PCI2_ARB	0x00040000
 #define MPC85xx_PORDEVSR_PCI1_ARB	0x00020000
@@ -1653,13 +1654,23 @@
 #define CFG_MPC85xx_PCIX_ADDR	(CFG_IMMR + CFG_MPC85xx_PCIX_OFFSET)
 #define CFG_MPC85xx_PCIX2_OFFSET	(0x9000)
 #define CFG_MPC85xx_PCIX2_ADDR	(CFG_IMMR + CFG_MPC85xx_PCIX2_OFFSET)
+#define CFG_MPC85xx_SATA1_OFFSET	(0x18000)
+#define CFG_MPC85xx_SATA1_ADDR	(CFG_IMMR + CFG_MPC85xx_SATA1_OFFSET)
+#define CFG_MPC85xx_SATA2_OFFSET	(0x19000)
+#define CFG_MPC85xx_SATA2_ADDR	(CFG_IMMR + CFG_MPC85xx_SATA2_OFFSET)
 #define CFG_MPC85xx_L2_OFFSET	(0x20000)
 #define CFG_MPC85xx_L2_ADDR	(CFG_IMMR + CFG_MPC85xx_L2_OFFSET)
 #define CFG_MPC85xx_DMA_OFFSET	(0x21000)
 #define CFG_MPC85xx_DMA_ADDR	(CFG_IMMR + CFG_MPC85xx_DMA_OFFSET)
+#define CFG_MPC85xx_ESDHC_OFFSET	(0x2e000)
+#define CFG_MPC85xx_ESDHC_ADDR	(CFG_IMMR + CFG_MPC85xx_ESDHC_OFFSET)
 #define CFG_MPC85xx_PIC_OFFSET	(0x40000)
 #define CFG_MPC85xx_PIC_ADDR	(CFG_IMMR + CFG_MPC85xx_PIC_OFFSET)
 #define CFG_MPC85xx_CPM_OFFSET	(0x80000)
 #define CFG_MPC85xx_CPM_ADDR	(CFG_IMMR + CFG_MPC85xx_CPM_OFFSET)
+#define CFG_MPC85xx_SERDES1_OFFSET	(0xE3000)
+#define CFG_MPC85xx_SERDES1_ADDR	(CFG_IMMR + CFG_MPC85xx_SERDES2_OFFSET)
+#define CFG_MPC85xx_SERDES2_OFFSET	(0xE3100)
+#define CFG_MPC85xx_SERDES2_ADDR	(CFG_IMMR + CFG_MPC85xx_SERDES2_OFFSET)
 
 #endif /*__IMMAP_85xx__*/
diff --git a/include/asm-ppc/mmu.h b/include/asm-ppc/mmu.h
index 050a7b6..8975e6c 100644
--- a/include/asm-ppc/mmu.h
+++ b/include/asm-ppc/mmu.h
@@ -431,6 +431,7 @@
 extern void disable_tlb(u8 esel);
 extern void invalidate_tlb(u8 tlb);
 extern void init_tlbs(void);
+extern unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg);
 
 #define SET_TLB_ENTRY(_tlb, _epn, _rpn, _perms, _wimge, _ts, _esel, _sz, _iprot) \
 	{ .tlb = _tlb, .epn = _epn, .rpn = _rpn, .perms = _perms, \
diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h
index dce4717..e07e5d3 100644
--- a/include/asm-ppc/processor.h
+++ b/include/asm-ppc/processor.h
@@ -926,6 +926,8 @@
 
 #define SVR_8533	0x803400
 #define SVR_8533_E	0x803C00
+#define SVR_8536	0x803700
+#define SVR_8536_E	0x803F00
 #define SVR_8540	0x803000
 #define SVR_8541	0x807200
 #define SVR_8541_E	0x807A00
diff --git a/include/configs/ATUM8548.h b/include/configs/ATUM8548.h
index 6aa881c..5bc28f1 100644
--- a/include/configs/ATUM8548.h
+++ b/include/configs/ATUM8548.h
@@ -55,18 +55,11 @@
 
 #define CONFIG_TSEC_ENET	1	/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for DDR setup*/
-#undef CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
-#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
-
 #define CONFIG_SYS_CLK_FREQ	33000000
 
 /*
@@ -104,33 +97,38 @@
 #define CFG_PCI2_ADDR	(CFG_CCSRBAR+0x9000)
 #define CFG_PCIE1_ADDR	(CFG_CCSRBAR+0xa000)
 
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
 
-#if defined(CONFIG_SPD_EEPROM)
-    /*
-     * Determine DDR configuration from I2C interface.
-     */
-    #define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
 
-#else
-    /*
-     * Manually set up DDR parameters
-     */
-    #define CFG_SDRAM_SIZE	1024		/* DDR is 1024MB */
-    #define CFG_DDR_CS0_BNDS	0x0000000f	/* 0-1024 */
-    #define CFG_DDR_CS0_CONFIG	0x80000102
-    #define CFG_DDR_TIMING_0	0x00260802
-    #define CFG_DDR_TIMING_1	0x38355322
-    #define CFG_DDR_TIMING_2	0x039048c7
-    #define CFG_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
-    #define CFG_DDR_MODE	0x00000432
-    #define CFG_DDR_INTERVAL	0x05150100
-    #define DDR_SDRAM_CFG	0x43000000
-#endif
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
+
+/* Manually set up DDR parameters */
+#define CFG_SDRAM_SIZE	1024		/* DDR is 1024MB */
+#define CFG_DDR_CS0_BNDS	0x0000000f	/* 0-1024 */
+#define CFG_DDR_CS0_CONFIG	0x80000102
+#define CFG_DDR_TIMING_0	0x00260802
+#define CFG_DDR_TIMING_1	0x38355322
+#define CFG_DDR_TIMING_2	0x039048c7
+#define CFG_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
+#define CFG_DDR_MODE	0x00000432
+#define CFG_DDR_INTERVAL	0x05150100
+#define DDR_SDRAM_CFG	0x43000000
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h
new file mode 100644
index 0000000..17cc934
--- /dev/null
+++ b/include/configs/MPC8536DS.h
@@ -0,0 +1,594 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8536ds board configuration file
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
+#define CONFIG_MPC8536		1
+#define CONFIG_MPC8536DS	1
+
+#define CONFIG_PCI		1	/* Enable PCI/PCIE */
+#define CONFIG_PCI1		1	/* Enable PCI controller 1 */
+#define CONFIG_PCIE1		1	/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2		1	/* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE3		1	/* PCIE controler 3 (ULI bridge) */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
+
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the CDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+extern unsigned long get_board_ddr_clk(unsigned long dummy);
+#endif
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
+/* #define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk(0) /\* ddrclk for MPC85xx *\/ FIXME-8536*/
+#define CONFIG_ICS307_REFCLK_HZ	33333000  /* ICS307 clock chip ref freq */
+#define CONFIG_GET_CLK_FROM_ICS307	  /* decode sysclk and ddrclk freq
+					     from ICS307 instead of switches */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
+
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+#define CFG_MEMTEST_START	0x00000000	/* memtest works on */
+#define CFG_MEMTEST_END		0x7fffffff
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+#define CFG_PCI1_ADDR		(CFG_CCSRBAR+0x8000)
+#define CFG_PCIE1_ADDR		(CFG_CCSRBAR+0xa000)
+#define CFG_PCIE2_ADDR		(CFG_CCSRBAR+0x9000)
+#define CFG_PCIE3_ADDR		(CFG_CCSRBAR+0xb000)
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#undef CONFIG_DDR_DLL
+
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
+#define CFG_SPD_BUS_NUM		1
+
+/* These are used when DDR doesn't use SPD. */
+#define CFG_SDRAM_SIZE		256		/* DDR is 256MB */
+#define CFG_DDR_CS0_BNDS	0x0000001F
+#define CFG_DDR_CS0_CONFIG	0x80010102	/* Enable, no interleaving */
+#define CFG_DDR_TIMING_3	0x00000000
+#define CFG_DDR_TIMING_0	0x00260802
+#define CFG_DDR_TIMING_1	0x3935d322
+#define CFG_DDR_TIMING_2	0x14904cc8
+#define CFG_DDR_MODE_1		0x00480432
+#define CFG_DDR_MODE_2		0x00000000
+#define CFG_DDR_INTERVAL	0x06180100
+#define CFG_DDR_DATA_INIT	0xdeadbeef
+#define CFG_DDR_CLK_CTRL	0x03800000
+#define CFG_DDR_OCD_CTRL	0x00000000
+#define CFG_DDR_OCD_STATUS	0x00000000
+#define CFG_DDR_CONTROL		0xC3008000	/* Type = DDR2 */
+#define CFG_DDR_CONTROL2	0x04400010
+
+#define CFG_DDR_ERR_INT_EN	0x0000000d
+#define CFG_DDR_ERR_DIS		0x00000000
+#define CFG_DDR_SBE		0x00010000
+
+/* FIXME: Not used in fixed_sdram function */
+#define CFG_DDR_MODE		0x00000022
+#define CFG_DDR_CS1_BNDS	0x00000000
+#define CFG_DDR_CS2_BNDS	0x00000FFF	/* Not done */
+#define CFG_DDR_CS3_BNDS	0x00000FFF	/* Not done */
+#define CFG_DDR_CS4_BNDS	0x00000FFF	/* Not done */
+#define CFG_DDR_CS5_BNDS	0x00000FFF	/* Not done */
+
+/* Make sure required options are set */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required")
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
+/*
+ * Memory map -- xxx -this is wrong, needs updating
+ *
+ * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
+ * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
+ * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
+ * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
+ *
+ * Localbus cacheable (TBD)
+ * 0xXXXX_XXXX	0xXXXX_XXXX	SRAM			YZ M Cacheable
+ *
+ * Localbus non-cacheable
+ * 0xe000_0000	0xe80f_ffff	Promjet/free		128M non-cacheable
+ * 0xe800_0000	0xefff_ffff	FLASH			128M non-cacheable
+ * 0xffdf_0000	0xffdf_7fff	PIXIS			32K non-cacheable TLB0
+ * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
+ * 0xffe0_0000	0xffef_ffff	CCSR			1M non-cacheable
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CFG_FLASH_BASE		0xe0000000	/* start of FLASH 128M */
+
+#define CFG_BR0_PRELIM		0xe8001001
+#define CFG_OR0_PRELIM		0xf8000ff7
+
+#define CFG_BR1_PRELIM		0xe0001001
+#define CFG_OR1_PRELIM		0xf8000ff7
+
+#define CFG_FLASH_BANKS_LIST	{CFG_FLASH_BASE + 0x8000000, CFG_FLASH_BASE}
+#define CFG_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CFG_MAX_FLASH_BANKS	2		/* number of banks */
+#define CFG_MAX_FLASH_SECT	1024		/* sectors per device */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_AMD_CHECK_DQ7
+
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+
+#define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
+#define PIXIS_BASE	0xffdf0000	/* PIXIS registers */
+
+#define CFG_BR3_PRELIM	(PIXIS_BASE | 0x0801)	/* port size 8bit */
+#define CFG_OR3_PRELIM		0xffffeff7	/* 32KB but only 4k mapped */
+
+#define PIXIS_ID		0x0	/* Board ID at offset 0 */
+#define PIXIS_VER		0x1	/* Board version at offset 1 */
+#define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
+#define PIXIS_CSR   		0x3	/* PIXIS General control/status register */
+#define PIXIS_RST		0x4	/* PIXIS Reset Control register */
+#define PIXIS_PWR		0x5	/* PIXIS Power status register */
+#define PIXIS_AUX		0x6	/* Auxiliary 1 register */
+#define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
+#define PIXIS_AUX2		0x8	/* Auxiliary 2 register */
+#define PIXIS_VCTL		0x10	/* VELA Control Register */
+#define PIXIS_VSTAT		0x11	/* VELA Status Register */
+#define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
+#define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
+#define PIXIS_VCORE0	 	0x14	/* VELA VCORE0 Register */
+#define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
+#define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
+#define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
+#define PIXIS_VSPEED2		0x19	/* VELA VSpeed 2 */
+#define PIXIS_VSYSCLK0		0x1A	/* VELA SYSCLK0 Register */
+#define PIXIS_VSYSCLK1		0x1B	/* VELA SYSCLK1 Register */
+#define PIXIS_VSYSCLK2		0x1C	/* VELA SYSCLK2 Register */
+#define PIXIS_VDDRCLK0		0x1D	/* VELA DDRCLK0 Register */
+#define PIXIS_VDDRCLK1		0x1E	/* VELA DDRCLK1 Register */
+#define PIXIS_VDDRCLK2		0x1F	/* VELA DDRCLK2 Register */
+#define PIXIS_VWATCH		0x24    /* Watchdog Register */
+#define PIXIS_LED		0x25    /* LED Register */
+
+/* old pixis referenced names */
+#define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
+#define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+#define CFG_PIXIS_VBOOT_MASK	0xc0
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK	1
+#define CFG_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
+#define CFG_INIT_RAM_END	0x00004000	/* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX	1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1	(CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef	CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+#define CFG_64BIT_STRTOUL		1
+#define CFG_64BIT_VSPRINTF		1
+
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES	{{0, 0x29}}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET		0x3000
+#define CFG_I2C2_OFFSET		0x3100
+
+/*
+ * I2C2 EEPROM
+ */
+#define CFG_ID_EEPROM
+#ifdef CFG_ID_EEPROM
+#define CONFIG_ID_EEPROM
+#define CFG_I2C_EEPROM_NXID
+#endif
+#define CFG_I2C_EEPROM_ADDR	0x57
+#define CFG_I2C_EEPROM_ADDR_LEN	1
+#define CFG_EEPROM_BUS_NUM	1
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS	0x00000000
+#define CFG_PCI_MEMORY_PHYS	0x00000000
+#define CFG_PCI_MEMORY_SIZE	0x80000000
+
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI1_IO_BASE	0x00000000
+#define CFG_PCI1_IO_PHYS	0xffc00000
+#define CFG_PCI1_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CFG_PCIE1_MEM_BASE	0x90000000
+#define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE	0x08000000	/* 128M */
+#define CFG_PCIE1_IO_BASE	0x00000000
+#define CFG_PCIE1_IO_PHYS	0xffc10000
+#define CFG_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#define CFG_PCIE2_MEM_BASE	0x98000000
+#define CFG_PCIE2_MEM_PHYS	CFG_PCIE2_MEM_BASE
+#define CFG_PCIE2_MEM_SIZE	0x08000000	/* 128M */
+#define CFG_PCIE2_IO_BASE	0x00000000
+#define CFG_PCIE2_IO_PHYS	0xffc20000
+#define CFG_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 3, direct to uli, tgtid 3, Base address 8000 */
+#define CFG_PCIE3_MEM_BASE	0xa0000000
+#define CFG_PCIE3_MEM_PHYS	CFG_PCIE3_MEM_BASE
+#define CFG_PCIE3_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCIE3_IO_BASE	0x00000000
+#define CFG_PCIE3_IO_PHYS	0xffc30000
+#define CFG_PCIE3_IO_SIZE	0x00010000	/* 64k */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET		CFG_PCIE3_IO_PHYS
+
+/*PCI video card used*/
+/*#define VIDEO_IO_OFFSET	CFG_PCI1_IO_PHYS*/
+
+/* video */
+#define CONFIG_VIDEO
+
+#if defined(CONFIG_VIDEO)
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+/*#define CONFIG_CONSOLE_CURSOR*/
+#define CFG_ISA_IO_BASE_ADDRESS CFG_PCIE3_IO_PHYS
+#endif
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+#undef CONFIG_RTL8139
+
+#ifdef CONFIG_RTL8139
+/* This macro is used by RTL8139 but not defined in PPC architecture */
+#define KSEG1ADDR(x)		({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
+#define _IO_BASE	0x00000000
+#endif
+
+#ifndef CONFIG_PCI_PNP
+	#define PCI_ENET0_IOADDR	CFG_PCI1_IO_BASE
+	#define PCI_ENET0_MEMADDR	CFG_PCI1_IO_BASE
+	#define PCI_IDSEL_NUMBER	0x11	/* IDSEL = AD11 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+
+#endif	/* CONFIG_PCI */
+
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CFG_SATA_MAX_DEVICE	2
+#define CONFIG_SATA1
+#define CFG_SATA1		CFG_MPC85xx_SATA1_ADDR
+#define CFG_SATA1_FLAGS		FLAGS_DMA
+#define CONFIG_SATA2
+#define CFG_SATA2		CFG_MPC85xx_SATA2_ADDR
+#define CFG_SATA2_FLAGS		FLAGS_DMA
+
+#ifdef CONFIG_FSL_SATA
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI	1
+#endif
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
+#define CONFIG_TSEC1	1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#define CONFIG_TSEC3	1
+#define CONFIG_TSEC3_NAME	"eTSEC3"
+
+#define TSEC1_PHY_ADDR		1	/* TSEC1 -> PHY1 */
+#define TSEC3_PHY_ADDR		0	/* TSEC3 -> PHY0 */
+
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX		0
+#define TSEC3_PHYIDX		0
+
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#if CFG_MONITOR_BASE > 0xfff80000
+#define CFG_ENV_ADDR		0xfff80000
+#else
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x60000)
+#endif
+#define CFG_ENV_SIZE		0x2000
+#define CFG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_NET
+#endif
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR	00:E0:0C:02:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR	00:E0:0C:02:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR	00:E0:0C:02:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR	00:E0:0C:02:03:FD
+#endif
+
+#define CONFIG_IPADDR		192.168.1.254
+
+#define CONFIG_HOSTNAME		unknown
+#define CONFIG_ROOTPATH		/opt/nfsroot
+#define CONFIG_BOOTFILE		uImage
+#define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */
+
+#define CONFIG_SERVERIP		192.168.1.1
+#define CONFIG_GATEWAYIP	192.168.1.1
+#define CONFIG_NETMASK		255.255.255.0
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+ "netdev=eth0\0"						\
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+ "tftpflash=tftpboot $loadaddr $uboot; "			\
+	"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+	"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+	"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
+ "consoledev=ttyS0\0"				\
+ "ramdiskaddr=2000000\0"			\
+ "ramdiskfile=8536ds/ramdisk.uboot\0"		\
+ "fdtaddr=c00000\0"				\
+ "fdtfile=8536ds/mpc8536ds.dtb\0"		\
+ "bdev=sda3\0"
+
+#define CONFIG_HDBOOT				\
+ "setenv bootargs root=/dev/$bdev rw "		\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $loadaddr $bootfile;"			\
+ "tftp $fdtaddr $fdtfile;"			\
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND		\
+ "setenv bootargs root=/dev/nfs rw "	\
+ "nfsroot=$serverip:$rootpath "		\
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND		\
+ "setenv bootargs root=/dev/ram rw "	\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $ramdiskaddr $ramdiskfile;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_HDBOOT
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 6351925..74f8605 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -48,13 +48,6 @@
 #define CONFIG_PCI
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
-
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
 /*
@@ -100,33 +93,33 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#undef CONFIG_FSL_DDR_INTERACTIVE
 
-/*
- * DDR Setup
- */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 
-#if defined(CONFIG_SPD_EEPROM)
-    /*
-     * Determine DDR configuration from I2C interface.
-     */
-    #define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
-#else
-    /*
-     * Manually set up DDR parameters
-     */
-    #define CFG_SDRAM_SIZE	128		/* DDR is 128MB */
-    #define CFG_DDR_CS0_BNDS	0x00000007	/* 0-128MB */
-    #define CFG_DDR_CS0_CONFIG	0x80000002
-    #define CFG_DDR_TIMING_1	0x37344321
-    #define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-    #define CFG_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
-    #define CFG_DDR_MODE	0x00000062	/* DLL,normal,seq,4/2.5 */
-    #define CFG_DDR_INTERVAL	0x05200100	/* autocharge,no open page */
-#endif
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
 
+/* These are used when DDR doesn't use SPD. */
+#define CFG_SDRAM_SIZE	128		/* DDR is 128MB */
+#define CFG_DDR_CS0_BNDS	0x00000007	/* 0-128MB */
+#define CFG_DDR_CS0_CONFIG	0x80000002
+#define CFG_DDR_TIMING_1	0x37344321
+#define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
+#define CFG_DDR_CONTROL		0xc2000000	/* unbuffered,no DYN_PWR */
+#define CFG_DDR_MODE		0x00000062	/* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL	0x05200100	/* autocharge,no open page */
 
 /*
  * SDRAM on the Local Bus
diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h
index b13c81c..1073e23 100644
--- a/include/configs/MPC8540EVAL.h
+++ b/include/configs/MPC8540EVAL.h
@@ -39,9 +39,6 @@
 #undef  CONFIG_PCI			    /* pci ethernet support	*/
 #define CONFIG_TSEC_ENET		    /* tsec ethernet support  */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM                   /* Use SPD EEPROM for DDR setup */
-#undef  CONFIG_DDR_ECC			    /* only for ECC DDR module */
-#define CONFIG_DDR_DLL                      /* possible DLL fix needed */
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
@@ -86,8 +83,6 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory  */
-#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 #define CFG_SDRAM_SIZE		256             /* DDR is now 256MB     */
 
 #if defined(CONFIG_RAM_AS_FLASH)
@@ -121,10 +116,27 @@
 #undef  CFG_RAMBOOT
 #endif
 
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_DLL                      /* possible DLL fix needed */
 
-/* Here some DDR setting should be added */
+#undef  CONFIG_DDR_ECC			    /* only for ECC DDR module */
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
 
+#define CFG_DDR_SDRAM_BASE	0x00000000
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index d948d76..29dff32 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -40,12 +40,6 @@
 #define CONFIG_PCI
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#undef CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
@@ -59,8 +53,6 @@
  */
 #define CONFIG_ASSUME_AMD_FLASH
 
-#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
-
 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif
@@ -85,13 +77,23 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
-/*
- * DDR Setup
- */
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#undef CONFIG_FSL_DDR_INTERACTIVE
+
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
 
 /*
  * Make sure required options are set
@@ -102,7 +104,6 @@
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -317,6 +318,9 @@
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
+#define CFG_64BIT_VSPRINTF	1
+#define CFG_64BIT_STRTOUL	1
+
 /*
  * I2C
  */
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 9a77b7b..5738192 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -46,15 +46,6 @@
 
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_DLL
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
-
-#define CONFIG_DDR_ECC_CMD
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 
 /*
@@ -64,8 +55,6 @@
  */
 #define CONFIG_ASSUME_AMD_FLASH
 
-#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
-
 #ifndef __ASSEMBLY__
 extern unsigned long get_board_sys_clk(unsigned long dummy);
 #endif
@@ -101,17 +90,27 @@
 #define CFG_PCIE2_ADDR		(CFG_CCSRBAR+0x9000)
 #define CFG_PCIE3_ADDR		(CFG_CCSRBAR+0xb000)
 
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
 
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
 #define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
 
-/*
- * Make sure required options are set
- */
+/* Make sure required options are set */
 #ifndef CONFIG_SPD_EEPROM
 #error ("CONFIG_SPD_EEPROM is required")
 #endif
@@ -242,6 +241,9 @@
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
+#define CFG_64BIT_STRTOUL		1
+#define CFG_64BIT_VSPRINTF		1
+
 /* I2C */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 33c5c93..ec0b4ff 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -46,15 +46,7 @@
 
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#undef CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
-
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
 #define CONFIG_FSL_VIA
@@ -67,8 +59,6 @@
  */
 #define CONFIG_ASSUME_AMD_FLASH
 
-#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
-
 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif
@@ -103,17 +93,27 @@
 #define CFG_PCI2_ADDR	(CFG_CCSRBAR+0x9000)
 #define CFG_PCIE1_ADDR	(CFG_CCSRBAR+0xa000)
 
-/*
- * DDR Setup
- */
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_DLL			/* possible DLL fix needed */
+
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
-/*
- * Make sure required options are set
- */
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
+
+/* Make sure required options are set */
 #ifndef CONFIG_SPD_EEPROM
 #error ("CONFIG_SPD_EEPROM is required")
 #endif
@@ -342,6 +342,9 @@
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
+#define CFG_64BIT_VSPRINTF	1
+#define CFG_64BIT_STRTOUL	1
+
 /*
  * I2C
  */
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index 85c235c..c07a725 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -40,13 +40,6 @@
 #define CONFIG_PCI
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#undef CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
-
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
 #define CONFIG_FSL_VIA
@@ -59,8 +52,6 @@
  */
 #define CONFIG_ASSUME_AMD_FLASH
 
-#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
-
 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif
@@ -85,24 +76,31 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
-/*
- * DDR Setup
- */
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#undef CONFIG_FSL_DDR_INTERACTIVE
+
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
-/*
- * Make sure required options are set
- */
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
+
+/* Make sure required options are set */
 #ifndef CONFIG_SPD_EEPROM
 #error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
 #endif
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -317,6 +315,9 @@
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
+#define CFG_64BIT_VSPRINTF	1
+#define CFG_64BIT_STRTOUL	1
+
 /*
  * I2C
  */
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 3567d1ce..a8e7c0a 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -46,13 +46,6 @@
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
-
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
 /*
@@ -96,33 +89,33 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#undef CONFIG_FSL_DDR_INTERACTIVE
 
-/*
- * DDR Setup
- */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 
-#if defined(CONFIG_SPD_EEPROM)
-    /*
-     * Determine DDR configuration from I2C interface.
-     */
-    #define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
-#else
-    /*
-     * Manually set up DDR parameters
-     */
-    #define CFG_SDRAM_SIZE	128		/* DDR is 128MB */
-    #define CFG_DDR_CS0_BNDS	0x00000007	/* 0-128MB */
-    #define CFG_DDR_CS0_CONFIG	0x80000002
-    #define CFG_DDR_TIMING_1	0x37344321
-    #define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-    #define CFG_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
-    #define CFG_DDR_MODE	0x00000062	/* DLL,normal,seq,4/2.5 */
-    #define CFG_DDR_INTERVAL	0x05200100	/* autocharge,no open page */
-#endif
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
 
+/* These are used when DDR doesn't use SPD.  */
+#define CFG_SDRAM_SIZE	128		/* DDR is 128MB */
+#define CFG_DDR_CS0_BNDS	0x00000007	/* 0-128MB */
+#define CFG_DDR_CS0_CONFIG	0x80000002
+#define CFG_DDR_TIMING_1	0x37344321
+#define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
+#define CFG_DDR_CONTROL		0xc2000000	/* unbuffered,no DYN_PWR */
+#define CFG_DDR_MODE		0x00000062	/* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL	0x05200100	/* autocharge,no open page */
 
 /*
  * SDRAM on the Local Bus
@@ -293,6 +286,9 @@
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
+#define CFG_64BIT_VSPRINTF	1
+#define CFG_64BIT_STRTOUL	1
+
 /*
  * I2C
  */
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index a82d528..8aeaa29 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -41,14 +41,6 @@
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_QE			/* Enable QE */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL			/* possible DLL fix needed */
-/*#define CONFIG_DDR_2T_TIMING		 Sets the 2T timing bit */
-
-/*#define CONFIG_DDR_ECC*/			/* only for ECC DDR module */
-/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/	/* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
-
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
 /*
@@ -58,8 +50,6 @@
  */
 #define CONFIG_ASSUME_AMD_FLASH
 
-#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
-
 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif						  /*Replace a call to get_clock_freq (after it is implemented)*/
@@ -95,24 +85,33 @@
 #define CFG_PCI1_ADDR           (CFG_CCSRBAR+0x8000)
 #define CFG_PCIE1_ADDR          (CFG_CCSRBAR+0xa000)
 
-/*
- * DDR Setup
- */
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_DLL			/* possible DLL fix needed */
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
-/*
- * Make sure required options are set
- */
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
+
+/* Make sure required options are set */
 #ifndef CONFIG_SPD_EEPROM
 #error ("CONFIG_SPD_EEPROM is required")
 #endif
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -302,6 +301,9 @@
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
+#define CFG_64BIT_VSPRINTF	1
+#define CFG_64BIT_STRTOUL	1
+
 /*
  * I2C
  */
diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
new file mode 100644
index 0000000..b0094f3
--- /dev/null
+++ b/include/configs/MPC8572DS.h
@@ -0,0 +1,576 @@
+/*
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8572ds board configuration file
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
+#define CONFIG_MPC8572		1
+#define CONFIG_MPC8572DS	1
+#define CONFIG_MP		1	/* support multiple processors */
+#define CONFIG_NUM_CPUS		2	/* Number of CPUs in the system */
+
+#define CONFIG_PCI		1	/* Enable PCI/PCIE */
+#define CONFIG_PCIE1		1	/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2		1	/* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE3		1	/* PCIE controler 3 (ULI bridge) */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
+
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the CDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+extern unsigned long get_board_ddr_clk(unsigned long dummy);
+#endif
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
+#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk(0) /* ddrclk for MPC85xx */
+#define CONFIG_ICS307_REFCLK_HZ	33333333  /* ICS307 clock chip ref freq */
+#define CONFIG_GET_CLK_FROM_ICS307	  /* decode sysclk and ddrclk freq
+					     from ICS307 instead of switches */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
+
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+#define CFG_MEMTEST_START	0x00000000	/* memtest works on */
+#define CFG_MEMTEST_END		0x7fffffff
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+#define CFG_PCIE3_ADDR		(CFG_CCSRBAR+0x8000)
+#define CFG_PCIE2_ADDR		(CFG_CCSRBAR+0x9000)
+#define CFG_PCIE1_ADDR		(CFG_CCSRBAR+0xa000)
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#undef CONFIG_DDR_DLL
+
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS	2
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS1	0x51	/* CTLR 0 DIMM 0 */
+#define SPD_EEPROM_ADDRESS2	0x52	/* CTLR 1 DIMM 0 */
+
+/* These are used when DDR doesn't use SPD.  */
+#define CFG_SDRAM_SIZE		256		/* DDR is 256MB */
+#define CFG_DDR_CS0_BNDS	0x0000001F
+#define CFG_DDR_CS0_CONFIG	0x80010102	/* Enable, no interleaving */
+#define CFG_DDR_TIMING_3	0x00000000
+#define CFG_DDR_TIMING_0	0x00260802
+#define CFG_DDR_TIMING_1	0x3935d322
+#define CFG_DDR_TIMING_2	0x14904cc8
+#define CFG_DDR_MODE_1		0x00480432
+#define CFG_DDR_MODE_2		0x00000000
+#define CFG_DDR_INTERVAL	0x06180100
+#define CFG_DDR_DATA_INIT	0xdeadbeef
+#define CFG_DDR_CLK_CTRL	0x03800000
+#define CFG_DDR_OCD_CTRL	0x00000000
+#define CFG_DDR_OCD_STATUS	0x00000000
+#define CFG_DDR_CONTROL		0xC3008000	/* Type = DDR2 */
+#define CFG_DDR_CONTROL2	0x04400010
+
+#define CFG_DDR_ERR_INT_EN	0x0000000d
+#define CFG_DDR_ERR_DIS		0x00000000
+#define CFG_DDR_SBE		0x00010000
+
+/*
+ * FIXME: Not used in fixed_sdram function
+ */
+#define CFG_DDR_MODE		0x00000022
+#define CFG_DDR_CS1_BNDS	0x00000000
+#define CFG_DDR_CS2_BNDS	0x00000FFF	/* Not done */
+#define CFG_DDR_CS3_BNDS	0x00000FFF	/* Not done */
+#define CFG_DDR_CS4_BNDS	0x00000FFF	/* Not done */
+#define CFG_DDR_CS5_BNDS	0x00000FFF	/* Not done */
+
+/*
+ * Make sure required options are set
+ */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required")
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
+ * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
+ * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
+ * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
+ *
+ * Localbus cacheable (TBD)
+ * 0xXXXX_XXXX	0xXXXX_XXXX	SRAM			YZ M Cacheable
+ *
+ * Localbus non-cacheable
+ * 0xe000_0000	0xe80f_ffff	Promjet/free		128M non-cacheable
+ * 0xe800_0000	0xefff_ffff	FLASH			128M non-cacheable
+ * 0xffdf_0000	0xffdf_7fff	PIXIS			32K non-cacheable TLB0
+ * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
+ * 0xffe0_0000	0xffef_ffff	CCSR			1M non-cacheable
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CFG_FLASH_BASE		0xe0000000	/* start of FLASH 128M */
+
+#define CFG_BR0_PRELIM		0xe8001001
+#define CFG_OR0_PRELIM		0xf8000ff7
+
+#define CFG_BR1_PRELIM		0xe0001001
+#define CFG_OR1_PRELIM		0xf8000ff7
+
+#define CFG_FLASH_BANKS_LIST	{CFG_FLASH_BASE + 0x8000000, CFG_FLASH_BASE}
+#define CFG_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CFG_MAX_FLASH_BANKS	2		/* number of banks */
+#define CFG_MAX_FLASH_SECT	1024		/* sectors per device */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_AMD_CHECK_DQ7
+
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+
+#define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
+#define PIXIS_BASE	0xffdf0000	/* PIXIS registers */
+
+#define CFG_BR3_PRELIM	(PIXIS_BASE | 0x0801)	/* port size 8bit */
+#define CFG_OR3_PRELIM		0xffffeff7	/* 32KB but only 4k mapped */
+
+#define PIXIS_ID		0x0	/* Board ID at offset 0 */
+#define PIXIS_VER		0x1	/* Board version at offset 1 */
+#define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
+#define PIXIS_CSR   		0x3	/* PIXIS General control/status register */
+#define PIXIS_RST		0x4	/* PIXIS Reset Control register */
+#define PIXIS_PWR		0x5	/* PIXIS Power status register */
+#define PIXIS_AUX		0x6	/* Auxiliary 1 register */
+#define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
+#define PIXIS_AUX2		0x8	/* Auxiliary 2 register */
+#define PIXIS_VCTL		0x10	/* VELA Control Register */
+#define PIXIS_VSTAT		0x11	/* VELA Status Register */
+#define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
+#define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
+#define PIXIS_VCORE0	 	0x14	/* VELA VCORE0 Register */
+#define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
+#define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
+#define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
+#define PIXIS_VSPEED2		0x19	/* VELA VSpeed 2 */
+#define PIXIS_VSYSCLK0		0x1C	/* VELA SYSCLK0 Register */
+#define PIXIS_VSYSCLK1		0x1D	/* VELA SYSCLK1 Register */
+#define PIXIS_VSYSCLK2		0x1E	/* VELA SYSCLK2 Register */
+#define PIXIS_VDDRCLK0		0x1F	/* VELA DDRCLK0 Register */
+#define PIXIS_VDDRCLK1		0x20	/* VELA DDRCLK1 Register */
+#define PIXIS_VDDRCLK2		0x21	/* VELA DDRCLK2 Register */
+#define PIXIS_VWATCH		0x24    /* Watchdog Register */
+#define PIXIS_LED		0x25    /* LED Register */
+
+/* old pixis referenced names */
+#define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
+#define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+#define CFG_PIXIS_VBOOT_MASK	0xc0
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK	1
+#define CFG_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
+#define CFG_INIT_RAM_END	0x00004000	/* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX	1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1	(CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef	CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+#define CFG_64BIT_VSPRINTF	1
+#define CFG_64BIT_STRTOUL	1
+
+/* new uImage format support */
+#define CONFIG_FIT		1
+#define CONFIG_FIT_VERBOSE	1 /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_EEPROM_ADDR	0x57
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET		0x3100
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS	0x00000000
+#define CFG_PCI_MEMORY_PHYS	0x00000000
+#define CFG_PCI_MEMORY_SIZE	0x80000000
+
+/* controller 3, direct to uli, tgtid 3, Base address 8000 */
+#define CFG_PCIE3_MEM_BASE	0x80000000
+#define CFG_PCIE3_MEM_PHYS	CFG_PCIE3_MEM_BASE
+#define CFG_PCIE3_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCIE3_IO_BASE	0x00000000
+#define CFG_PCIE3_IO_PHYS	0xffc00000
+#define CFG_PCIE3_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#define CFG_PCIE2_MEM_BASE	0xa0000000
+#define CFG_PCIE2_MEM_PHYS	CFG_PCIE2_MEM_BASE
+#define CFG_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCIE2_IO_BASE	0x00000000
+#define CFG_PCIE2_IO_PHYS	0xffc10000
+#define CFG_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CFG_PCIE1_MEM_BASE	0xc0000000
+#define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCIE1_IO_BASE	0x00000000
+#define CFG_PCIE1_IO_PHYS	0xffc20000
+#define CFG_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+#if defined(CONFIG_PCI)
+
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET		CFG_PCIE1_IO_PHYS
+
+/* video */
+#define CONFIG_VIDEO
+
+#if defined(CONFIG_VIDEO)
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+/*#define CONFIG_CONSOLE_CURSOR*/
+#define CFG_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#endif
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+#undef CONFIG_RTL8139
+
+#ifdef CONFIG_RTL8139
+/* This macro is used by RTL8139 but not defined in PPC architecture */
+#define KSEG1ADDR(x)		(x)
+#define _IO_BASE	0x00000000
+#endif
+
+#ifndef CONFIG_PCI_PNP
+	#define PCI_ENET0_IOADDR	CFG_PCIE3_IO_BASE
+	#define PCI_ENET0_MEMADDR	CFG_PCIE3_IO_BASE
+	#define PCI_IDSEL_NUMBER	0x11	/* IDSEL = AD11 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID	4
+#define CFG_SCSI_MAX_LUN	1
+#define CFG_SCSI_MAX_DEVICE	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE	CFG_SCSI_MAX_DEVICE
+#endif /* SCSI */
+
+#endif	/* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI	1
+#endif
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
+#define CONFIG_TSEC1	1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#define CONFIG_TSEC2	1
+#define CONFIG_TSEC2_NAME	"eTSEC2"
+#define CONFIG_TSEC3	1
+#define CONFIG_TSEC3_NAME	"eTSEC3"
+#define CONFIG_TSEC4	1
+#define CONFIG_TSEC4_NAME	"eTSEC4"
+
+#define TSEC1_PHY_ADDR		0
+#define TSEC2_PHY_ADDR		1
+#define TSEC3_PHY_ADDR		2
+#define TSEC4_PHY_ADDR		3
+
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC3_PHYIDX		0
+#define TSEC4_PHYIDX		0
+
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#if CFG_MONITOR_BASE > 0xfff80000
+#define CFG_ENV_ADDR		0xfff80000
+#else
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x70000)
+#endif
+#define CFG_ENV_SIZE		0x2000
+#define CFG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_SCSI
+#define CONFIG_CMD_EXT2
+#endif
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR	00:E0:0C:02:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR	00:E0:0C:02:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR	00:E0:0C:02:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR	00:E0:0C:02:03:FD
+#endif
+
+#define CONFIG_IPADDR		192.168.1.254
+
+#define CONFIG_HOSTNAME		unknown
+#define CONFIG_ROOTPATH		/opt/nfsroot
+#define CONFIG_BOOTFILE		uImage
+#define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */
+
+#define CONFIG_SERVERIP		192.168.1.1
+#define CONFIG_GATEWAYIP	192.168.1.1
+#define CONFIG_NETMASK		255.255.255.0
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+ "netdev=eth0\0"						\
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+ "tftpflash=tftpboot $loadaddr $uboot; "			\
+	"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+	"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+	"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
+ "consoledev=ttyS0\0"				\
+ "ramdiskaddr=2000000\0"			\
+ "ramdiskfile=8572ds/ramdisk.uboot\0"		\
+ "fdtaddr=c00000\0"				\
+ "fdtfile=8572ds/mpc8572ds.dtb\0"		\
+ "bdev=sda3\0"
+
+#define CONFIG_HDBOOT				\
+ "setenv bootargs root=/dev/$bdev rw "		\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $loadaddr $bootfile;"			\
+ "tftp $fdtaddr $fdtfile;"			\
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND		\
+ "setenv bootargs root=/dev/nfs rw "	\
+ "nfsroot=$serverip:$rootpath "		\
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND		\
+ "setenv bootargs root=/dev/ram rw "	\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $ramdiskaddr $ramdiskfile;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_HDBOOT
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/PM854.h b/include/configs/PM854.h
index f2c11b0..aa6095f 100644
--- a/include/configs/PM854.h
+++ b/include/configs/PM854.h
@@ -44,12 +44,6 @@
 #define CONFIG_PCI
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#undef	CONFIG_SPD_EEPROM		/* do not use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_MEM_INIT_VALUE		0xDEADBEEF
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
@@ -96,32 +90,36 @@
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
 
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#undef CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_SPD
+#define CONFIG_DDR_DLL                      /* possible DLL fix needed */
+#define CONFIG_DDR_ECC			    /* only for ECC DDR module */
+
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
 
-#if defined(CONFIG_SPD_EEPROM)
-    /*
-     * Determine DDR configuration from I2C interface.
-     */
-    #define SPD_EEPROM_ADDRESS	0x58		/* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
 
-#else
-    /*
-     * Manually set up DDR parameters
-     */
-    #define CFG_SDRAM_SIZE	256		/* DDR is 256 MB */
-    #define CFG_DDR_CS0_BNDS	0x0000000f	/* 0-256MB */
-    #define CFG_DDR_CS0_CONFIG	0x80000102
-    #define CFG_DDR_TIMING_1	0x47444321
-    #define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-    #define CFG_DDR_CONTROL	0xc2008000	/* unbuffered,no DYN_PWR */
-    #define CFG_DDR_MODE	0x00000062	/* DLL,normal,seq,4/2.5 */
-    #define CFG_DDR_INTERVAL	0x045b0100	/* autocharge,no open page */
-#endif
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x58	/* CTLR 0 DIMM 0 */
 
+/* Manually set up DDR parameters */
+#define CFG_SDRAM_SIZE	256		/* DDR is 256 MB */
+#define CFG_DDR_CS0_BNDS	0x0000000f	/* 0-256MB */
+#define CFG_DDR_CS0_CONFIG	0x80000102
+#define CFG_DDR_TIMING_1	0x47444321
+#define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
+#define CFG_DDR_CONTROL	0xc2008000	/* unbuffered,no DYN_PWR */
+#define CFG_DDR_MODE	0x00000062	/* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL	0x045b0100	/* autocharge,no open page */
 
 /*
  * SDRAM on the Local Bus
diff --git a/include/configs/PM856.h b/include/configs/PM856.h
index b2cf060..244f09a 100644
--- a/include/configs/PM856.h
+++ b/include/configs/PM856.h
@@ -45,11 +45,6 @@
 #define CONFIG_PCI
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#undef  CONFIG_SPD_EEPROM		/* do not use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-#define CONFIG_MEM_INIT_VALUE		0xDEADBEEF
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
@@ -97,33 +92,36 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#undef CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_SPD
+#define CONFIG_DDR_DLL                      /* possible DLL fix needed */
+#define CONFIG_DDR_ECC			    /* only for ECC DDR module */
 
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
 
-#if defined(CONFIG_SPD_EEPROM)
-    /*
-     * Determine DDR configuration from I2C interface.
-     */
-    #define SPD_EEPROM_ADDRESS	0x58		/* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
 
-#else
-    /*
-     * Manually set up DDR parameters
-     */
-    #define CFG_SDRAM_SIZE	256		/* DDR is 256 MB */
-    #define CFG_DDR_CS0_BNDS	0x0000000f	/* 0-256MB */
-    #define CFG_DDR_CS0_CONFIG	0x80000102
-    #define CFG_DDR_TIMING_1	0x47444321
-    #define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-    #define CFG_DDR_CONTROL	0xc2008000	/* unbuffered,no DYN_PWR */
-    #define CFG_DDR_MODE	0x00000062	/* DLL,normal,seq,4/2.5 */
-    #define CFG_DDR_INTERVAL	0x045b0100	/* autocharge,no open page */
-#endif
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x58	/* CTLR 0 DIMM 0 */
 
+/* Manually set up DDR parameters */
+#define CFG_SDRAM_SIZE	256		/* DDR is 256 MB */
+#define CFG_DDR_CS0_BNDS	0x0000000f	/* 0-256MB */
+#define CFG_DDR_CS0_CONFIG	0x80000102
+#define CFG_DDR_TIMING_1	0x47444321
+#define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
+#define CFG_DDR_CONTROL	0xc2008000	/* unbuffered,no DYN_PWR */
+#define CFG_DDR_MODE	0x00000062	/* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL	0x045b0100	/* autocharge,no open page */
 
 /*
  * SDRAM on the Local Bus
diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
index 6033d93..93509ee 100644
--- a/include/configs/SBC8540.h
+++ b/include/configs/SBC8540.h
@@ -103,18 +103,34 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	 */
-#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 #define CFG_SDRAM_SIZE		512		/* DDR is 512MB */
-#define SPD_EEPROM_ADDRESS	0x55		/*  DDR DIMM */
 
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#undef CONFIG_FSL_DDR_INTERACTIVE
 #undef  CONFIG_DDR_ECC				/* only for ECC DDR module	*/
 #undef  CONFIG_SPD_EEPROM			/* Use SPD EEPROM for DDR setup */
+#undef  CONFIG_DDR_SPD
 
 #if defined(CONFIG_MPC85xx_REV1)
   #define CONFIG_DDR_DLL			/* possible DLL fix needed	*/
 #endif
 
+#undef  CONFIG_DDR_ECC			    /* only for ECC DDR module */
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x55	/* CTLR 0 DIMM 0 */
+
 #undef CONFIG_CLOCKS_IN_MHZ
 
 #if defined(CONFIG_RAM_AS_FLASH)
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index d84554e..5e1cf95 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -137,6 +137,10 @@
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
 #if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560)
 /* TQM8540 & 8560 need DLL-override */
 #define CONFIG_DDR_DLL				/* DLL fix needed	*/
diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index b4238e5..9ef0bfd 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -47,19 +47,11 @@
 
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#undef CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
-#undef CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
-#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
-
 #define CONFIG_SYS_CLK_FREQ	66000000 /* SBC8548 default SYSCLK */
 
 /*
@@ -94,13 +86,26 @@
 #define CFG_PCI2_ADDR	(CFG_CCSRBAR+0x9000)
 #define CFG_PCIE1_ADDR	(CFG_CCSRBAR+0xa000)
 
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#undef CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_SPD
+#undef CONFIG_DDR_ECC			/* only for ECC DDR module */
 
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
 
 /*
  * Make sure required options are set
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index b244eef..99d328c 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -97,18 +97,34 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	 */
-#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 #define CFG_SDRAM_SIZE		512		/* DDR is 512MB */
-#define SPD_EEPROM_ADDRESS	0x55		/*  DDR DIMM */
 
-#undef  CONFIG_DDR_ECC			/* only for ECC DDR module	*/
-#undef  CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#undef  CONFIG_DDR_ECC				/* only for ECC DDR module	*/
+#undef  CONFIG_SPD_EEPROM			/* Use SPD EEPROM for DDR setup */
+#undef  CONFIG_DDR_SPD
 
 #if defined(CONFIG_MPC85xx_REV1)
-  #define CONFIG_DDR_DLL		/* possible DLL fix needed	*/
+  #define CONFIG_DDR_DLL			/* possible DLL fix needed	*/
 #endif
 
+#undef  CONFIG_DDR_ECC			    /* only for ECC DDR module */
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x55	/* CTLR 0 DIMM 0 */
+
 #undef CONFIG_CLOCKS_IN_MHZ
 
 #if defined(CONFIG_RAM_AS_FLASH)
diff --git a/include/configs/socrates.h b/include/configs/socrates.h
index 8a64942..15abec1 100644
--- a/include/configs/socrates.h
+++ b/include/configs/socrates.h
@@ -93,11 +93,25 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	*/
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
 
 #define CONFIG_DDR_DEFAULT_CL	30		/* CAS latency 3	*/
 
@@ -114,13 +128,6 @@
 #define CFG_DDR_CLK_CONTROL		0x03800000
 #define CFG_SDRAM_SIZE			256 /* in Megs */
 
-#define CONFIG_SPD_EEPROM	1 	/* Use SPD EEPROM for DDR setup*/
-#define SPD_EEPROM_ADDRESS	0x50		/* DDR DIMM */
-#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
-
-/*
- * Flash on the Local Bus
- */
 /*
  * Flash on the LocalBus
  */
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index 6e8213d..ea79de7 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -47,10 +47,6 @@
 #define CONFIG_TSEC_ENET		/* tsec ethernet support*/
 #undef  CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
-#undef  CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_DDR_DLL                  /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
@@ -118,19 +114,27 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#undef CONFIG_FSL_DDR_INTERACTIVE
 
-/*
- * DDR Setup
- */
+#undef  CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_DDR_DLL                  /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory  */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 
-#define SPD_EEPROM_ADDRESS	0x54		/*  DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x54	/* CTLR 0 DIMM 0 */
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index 4f1c156..ac349df 100644
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -47,10 +47,6 @@
 #define CONFIG_TSEC_ENET		/* tsec ethernet support*/
 #undef CONFIG_ETHER_ON_FCC		/* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
-#undef	CONFIG_DDR_ECC			/* only for ECC DDR module */
-#undef CONFIG_DDR_DLL			/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
@@ -131,19 +127,27 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#undef CONFIG_FSL_DDR_INTERACTIVE
 
-/*
- * DDR Setup
- */
+#undef	CONFIG_DDR_ECC			/* only for ECC DDR module */
+#undef CONFIG_DDR_DLL			/* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory  */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 
-#define SPD_EEPROM_ADDRESS	0x54		/*  DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x54	/* CTLR 0 DIMM 0 */
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
diff --git a/include/pci_ids.h b/include/pci_ids.h
index 165456b..ae642b1 100644
--- a/include/pci_ids.h
+++ b/include/pci_ids.h
@@ -2057,6 +2057,8 @@
 #define PCI_DEVICE_ID_MICROGATE_SCA	0x0030
 
 #define PCI_VENDOR_ID_FREESCALE		0x1957
+#define PCI_DEVICE_ID_MPC8536E		0x0050
+#define PCI_DEVICE_ID_MPC8536		0x0051
 #define PCI_DEVICE_ID_MPC8548E		0x0012
 #define PCI_DEVICE_ID_MPC8548		0x0013
 #define PCI_DEVICE_ID_MPC8543E		0x0014