| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * (C) Copyright 2011 |
| * Marvell Semiconductor <www.marvell.com> |
| * Written-by: Lei Wen <leiwen@marvell.com> |
| */ |
| |
| /* |
| * This file should be included in board config header file. |
| * |
| * It supports common definitions for MVEBU platforms |
| */ |
| |
| #ifndef _MVEBU_CONFIG_H |
| #define _MVEBU_CONFIG_H |
| |
| #include <asm/arch/soc.h> |
| |
| #if defined(CONFIG_ARMADA_XP) || defined(CONFIG_ARMADA_375) \ |
| || defined(CONFIG_ARMADA_38X) |
| /* |
| * Set this for the common xor register definitions needed in dram.c |
| * for A38x as well here. |
| */ |
| #define MV88F78X60 /* for the DDR training bin_hdr code */ |
| #endif |
| |
| #define CONFIG_SYS_L2_PL310 |
| |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ |
| #endif |
| |
| /* |
| * By default kwbimage.cfg from board specific folder is used |
| * If for some board, different configuration file need to be used, |
| * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file |
| */ |
| #ifndef CONFIG_SYS_KWD_CONFIG |
| #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg |
| #endif /* CONFIG_SYS_KWD_CONFIG */ |
| |
| /* Add target to build it automatically upon "make" */ |
| #ifdef CONFIG_SPL |
| #define CONFIG_BUILD_TARGET "u-boot-spl.kwb" |
| #endif |
| |
| /* end of 16M scrubbed by training in bootrom */ |
| #define CONFIG_SYS_INIT_SP_ADDR 0x00FF0000 |
| #define CONFIG_NR_DRAM_BANKS_MAX 2 |
| |
| #define MV_UART_CONSOLE_BASE MVEBU_UART0_BASE |
| |
| /* |
| * SPI Flash configuration |
| */ |
| #ifdef CONFIG_CMD_SF |
| #ifndef CONFIG_ENV_SPI_BUS |
| # define CONFIG_ENV_SPI_BUS 0 |
| #endif |
| #ifndef CONFIG_ENV_SPI_CS |
| # define CONFIG_ENV_SPI_CS 0 |
| #endif |
| #ifndef CONFIG_ENV_SPI_MAX_HZ |
| # define CONFIG_ENV_SPI_MAX_HZ 50000000 |
| #endif |
| #endif |
| |
| /* Needed for SPI NOR booting in SPL */ |
| #define CONFIG_DM_SEQ_ALIAS 1 |
| |
| /* |
| * Ethernet Driver configuration |
| */ |
| #ifdef CONFIG_CMD_NET |
| #define CONFIG_MII /* expose smi ove miiphy interface */ |
| #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ |
| #define CONFIG_ARP_TIMEOUT 200 |
| #define CONFIG_NET_RETRY_COUNT 50 |
| #endif /* CONFIG_CMD_NET */ |
| |
| /* |
| * I2C related stuff |
| */ |
| #ifdef CONFIG_CMD_I2C |
| #ifndef CONFIG_SYS_I2C_SOFT |
| #define CONFIG_I2C_MVTWSI |
| #endif |
| #define CONFIG_SYS_I2C_SLAVE 0x0 |
| #define CONFIG_SYS_I2C_SPEED 100000 |
| #endif |
| |
| /* Use common timer */ |
| #define CONFIG_SYS_TIMER_COUNTS_DOWN |
| #define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14) |
| #define CONFIG_SYS_TIMER_RATE 25000000 |
| |
| #endif /* __MVEBU_CONFIG_H */ |
