| if ARCH_UNIPHIER |
| |
| config SYS_CONFIG_NAME |
| default "uniphier" |
| |
| config ARCH_UNIPHIER_32BIT |
| bool |
| select CPU_V7 |
| select CPU_V7_HAS_NONSEC |
| select ARMV7_NONSEC |
| select ARCH_SUPPORT_PSCI |
| |
| choice |
| prompt "UniPhier SoC select" |
| default ARCH_UNIPHIER_V7_MULTI |
| |
| config ARCH_UNIPHIER_LD4_SLD8 |
| bool "UniPhier LD4/sLD8 SoCs" |
| select ARCH_UNIPHIER_32BIT |
| |
| config ARCH_UNIPHIER_V7_MULTI |
| bool "UniPhier Pro4/Pro5/PXs2/LD6b SoCs" |
| select ARCH_UNIPHIER_32BIT |
| |
| config ARCH_UNIPHIER_V8_MULTI |
| bool "UniPhier V8 SoCs" |
| depends on !SPL |
| select ARM64 |
| select CMD_UNZIP |
| |
| endchoice |
| |
| config ARCH_UNIPHIER_LD4 |
| bool "Enable UniPhier LD4 SoC support" |
| depends on ARCH_UNIPHIER_LD4_SLD8 |
| default y |
| |
| config ARCH_UNIPHIER_SLD8 |
| bool "Enable UniPhier sLD8 SoC support" |
| depends on ARCH_UNIPHIER_LD4_SLD8 |
| default y |
| |
| config ARCH_UNIPHIER_PRO4 |
| bool "Enable UniPhier Pro4 SoC support" |
| depends on ARCH_UNIPHIER_V7_MULTI |
| default y |
| |
| config ARCH_UNIPHIER_PRO5 |
| bool "Enable UniPhier Pro5 SoC support" |
| depends on ARCH_UNIPHIER_V7_MULTI |
| default y |
| |
| config ARCH_UNIPHIER_PXS2 |
| bool "Enable UniPhier Pxs2 SoC support" |
| depends on ARCH_UNIPHIER_V7_MULTI |
| default y |
| |
| config ARCH_UNIPHIER_LD6B |
| bool "Enable UniPhier LD6b SoC support" |
| depends on ARCH_UNIPHIER_V7_MULTI |
| default y |
| |
| config ARCH_UNIPHIER_LD11 |
| bool "Enable UniPhier LD11 SoC support" |
| depends on ARCH_UNIPHIER_V8_MULTI |
| default y |
| |
| config ARCH_UNIPHIER_LD20 |
| bool "Enable UniPhier LD20 SoC support" |
| depends on ARCH_UNIPHIER_V8_MULTI |
| select OF_BOARD_SETUP |
| default y |
| |
| config ARCH_UNIPHIER_PXS3 |
| bool "Enable UniPhier PXs3 SoC support" |
| depends on ARCH_UNIPHIER_V8_MULTI |
| default y |
| |
| config CACHE_UNIPHIER |
| bool "Enable the UniPhier L2 cache controller" |
| depends on ARCH_UNIPHIER_32BIT |
| select SYS_CACHE_SHIFT_7 |
| default y |
| help |
| This option allows to use the UniPhier System Cache as L2 cache. |
| |
| config MICRO_SUPPORT_CARD |
| bool "Use Micro Support Card" |
| help |
| This option provides support for the expansion board, available |
| on some UniPhier reference boards. |
| |
| Say Y to use the on-board UART, Ether, LED devices. |
| |
| config CMD_PINMON |
| bool "Enable boot mode pins monitor command" |
| default y |
| help |
| The command "pinmon" shows the state of the boot mode pins. |
| The boot mode pins are latched when the system reset is deasserted |
| and determine which device the system should load a boot image from. |
| |
| config CMD_DDRPHY_DUMP |
| bool "Enable dump command of DDR PHY parameters" |
| depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || \ |
| ARCH_UNIPHIER_SLD8 || ARCH_UNIPHIER_LD11 |
| default y |
| help |
| The command "ddrphy" shows the resulting parameters of DDR PHY |
| training; it is useful for the evaluation of DDR PHY training. |
| |
| config CMD_DDRMPHY_DUMP |
| bool "Enable dump command of DDR Multi PHY parameters" |
| depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B |
| default y |
| help |
| The command "ddrmphy" shows the resulting parameters of DDR Multi PHY |
| training; it is useful for the evaluation of DDR Multi PHY training. |
| |
| config SYS_SOC |
| default "uniphier-v7" if ARCH_UNIPHIER_LD4_SLD8 || ARCH_UNIPHIER_V7_MULTI |
| endif |
