blob: 2d882174de0d5c9f68be3efd3fa6029153432415 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*/
#include <common.h>
#include <debug_uart.h>
#include <linux/sizes.h>
#include <asm/arch/at91sam9263.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_matrix.h>
#include <asm/arch/at91_pio.h>
#include <asm/arch/clk.h>
#include <asm/io.h>
#include <asm/arch/gpio.h>
#include <asm/arch/hardware.h>
#include <lcd.h>
#include <atmel_lcdc.h>
#include <asm/mach-types.h>
DECLARE_GLOBAL_DATA_PTR;
/* ------------------------------------------------------------------------- */
/*
* Miscelaneous platform dependent initialisations
*/
#ifdef CONFIG_CMD_NAND
static void at91sam9263ek_nand_hw_init(void)
{
unsigned long csa;
at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0;
at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
/* Enable CS3 */
csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
writel(csa, &matrix->csa[0]);
/* Enable CS3 */
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(2),
&smc->cs[3].mode);
at91_periph_clk_enable(ATMEL_ID_PIOA);
at91_periph_clk_enable(ATMEL_ID_PIOCDE);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
#endif
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
.vl_col = 240,
.vl_row = 320,
.vl_clk = 4965000,
.vl_sync = ATMEL_LCDC_INVLINE_INVERTED |
ATMEL_LCDC_INVFRAME_INVERTED,
.vl_bpix = 3,
.vl_tft = 1,
.vl_hsync_len = 5,
.vl_left_margin = 1,
.vl_right_margin = 33,
.vl_vsync_len = 1,
.vl_upper_margin = 1,
.vl_lower_margin = 0,
.mmio = ATMEL_BASE_LCDC,
};
void lcd_enable(void)
{
at91_set_pio_value(AT91_PIO_PORTA, 30, 1); /* power up */
}
void lcd_disable(void)
{
at91_set_pio_value(AT91_PIO_PORTA, 30, 0); /* power down */
}
static void at91sam9263ek_lcd_hw_init(void)
{
at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */
at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */
at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDDEN */
at91_set_b_periph(AT91_PIO_PORTB, 9, 0); /* LCDCC */
at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD2 */
at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD3 */
at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD4 */
at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD5 */
at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD6 */
at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD7 */
at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD10 */
at91_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD11 */
at91_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD12 */
at91_set_b_periph(AT91_PIO_PORTC, 12, 0); /* LCDD13 */
at91_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD14 */
at91_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD15 */
at91_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD18 */
at91_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD19 */
at91_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDD20 */
at91_set_b_periph(AT91_PIO_PORTC, 17, 0); /* LCDD21 */
at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */
at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */
at91_periph_clk_enable(ATMEL_ID_LCDC);
gd->fb_base = ATMEL_BASE_SRAM0;
}
#ifdef CONFIG_LCD_INFO
#include <nand.h>
#include <version.h>
#ifdef CONFIG_MTD_NOR_FLASH
extern flash_info_t flash_info[];
#endif
void lcd_show_board_info(void)
{
ulong dram_size, nand_size;
#ifdef CONFIG_MTD_NOR_FLASH
ulong flash_size;
#endif
int i;
char temp[32];
lcd_printf ("%s\n", U_BOOT_VERSION);
lcd_printf ("(C) 2008 ATMEL Corp\n");
lcd_printf ("at91support@atmel.com\n");
lcd_printf ("%s CPU at %s MHz\n",
ATMEL_CPU_NAME,
strmhz(temp, get_cpu_clk_rate()));
dram_size = 0;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
dram_size += gd->bd->bi_dram[i].size;
nand_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
nand_size += get_nand_dev_by_index(i)->size;
#ifdef CONFIG_MTD_NOR_FLASH
flash_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
flash_size += flash_info[i].size;
#endif
lcd_printf (" %ld MB SDRAM, %ld MB NAND",
dram_size >> 20,
nand_size >> 20 );
#ifdef CONFIG_MTD_NOR_FLASH
lcd_printf (",\n %ld MB NOR",
flash_size >> 20);
#endif
lcd_puts ("\n");
}
#endif /* CONFIG_LCD_INFO */
#endif
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
void board_debug_uart_init(void)
{
at91_seriald_hw_init();
}
#endif
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
#ifdef CONFIG_DEBUG_UART
debug_uart_init();
#endif
return 0;
}
#endif
int board_init(void)
{
/* arch number of AT91SAM9263EK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9263EK;
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_CMD_NAND
at91sam9263ek_nand_hw_init();
#endif
#ifdef CONFIG_USB_OHCI_NEW
at91_uhp_hw_init();
#endif
#ifdef CONFIG_LCD
at91sam9263ek_lcd_hw_init();
#endif
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
#ifdef CONFIG_RESET_PHY_R
void reset_phy(void)
{
}
#endif