blob: 9e8e1f36f7a6f0e8dade8f5fad25e55355785b0b [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2007-2013
* Stelian Pop <stelian.pop@leadtechdesign.com>
* Lead Tech Design <www.leadtechdesign.com>
* Thomas Petazzoni, Free Electrons, <thomas.petazzoni@free-electrons.com>
* Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
*/
#include <common.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_matrix.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <asm-generic/gpio.h>
#include <asm/io.h>
#include <net.h>
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_CMD_NAND
static void usb_a9263_nand_hw_init(void)
{
unsigned long csa;
at91_smc_t *smc = (at91_smc_t *)ATMEL_BASE_SMC0;
at91_matrix_t *matrix = (at91_matrix_t *)ATMEL_BASE_MATRIX;
/* Enable CS3 */
csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
writel(csa, &matrix->csa[0]);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_8 |
AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode);
at91_periph_clk_enable(ATMEL_ID_PIOA);
at91_periph_clk_enable(ATMEL_ID_PIOCDE);
/* Configure RDY/BSY */
gpio_request(CONFIG_SYS_NAND_READY_PIN, "NAND ready/busy");
gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
/* Enable NandFlash */
gpio_request(CONFIG_SYS_NAND_ENABLE_PIN, "NAND enable");
gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
#endif
#ifdef CONFIG_MACB
static void usb_a9263_macb_hw_init(void)
{
at91_periph_clk_enable(ATMEL_ID_EMAC);
/*
* Disable pull-up on:
* RXDV (PC25) => PHY normal mode (not Test mode)
* ERX0 (PE25) => PHY ADDR0
* ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0
*
* PHY has internal weak pull-up/pull-down
*/
gpio_request(GPIO_PIN_PC(25), "PHY mode");
gpio_direction_input(GPIO_PIN_PC(25));
gpio_request(GPIO_PIN_PE(25), "PHY ADDR0");
gpio_direction_input(GPIO_PIN_PE(25));
gpio_request(GPIO_PIN_PE(26), "PHY ADDR1");
gpio_direction_input(GPIO_PIN_PE(26));
at91_phy_reset();
/* It will set proper pinmux for ports PC25, PE25-26 */
at91_macb_hw_init();
}
#endif
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_CMD_NAND
usb_a9263_nand_hw_init();
#endif
#ifdef CONFIG_MACB
usb_a9263_macb_hw_init();
#endif
#ifdef CONFIG_USB_OHCI_NEW
at91_uhp_hw_init();
#endif
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_MACB
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x0001);
#endif
return rc;
}