| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * Copyright (C) 2014 Stefan Roese <sr@denx.de> | |
| * | |
| * Based on: gw_ventana_spl.c which is: | |
| * Copyright (C) 2014 Gateworks Corporation | |
| */ | |
| #include <common.h> | |
| #include <i2c.h> | |
| #include <asm/io.h> | |
| #include <asm/arch/iomux.h> | |
| #include <asm/arch/mx6-ddr.h> | |
| #include <asm/arch/mx6-pins.h> | |
| #include <asm/arch/sys_proto.h> | |
| #include <asm/mach-imx/boot_mode.h> | |
| #include <asm/mach-imx/iomux-v3.h> | |
| #include <asm/mach-imx/mxc_i2c.h> | |
| #include <spl.h> | |
| #include "platinum.h" | |
| #undef RTT_NOM_120OHM /* use 120ohm Rtt_nom vs 60ohm (lower power) */ | |
| /* Configure MX6Q/DUAL mmdc DDR io registers */ | |
| struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = { | |
| /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */ | |
| .dram_sdclk_0 = 0x00020030, | |
| .dram_sdclk_1 = 0x00020030, | |
| .dram_cas = 0x00020030, | |
| .dram_ras = 0x00020030, | |
| .dram_reset = 0x00020030, | |
| /* SDCKE[0:1]: 100k pull-up */ | |
| .dram_sdcke0 = 0x00003000, | |
| .dram_sdcke1 = 0x00003000, | |
| /* SDBA2: pull-up disabled */ | |
| .dram_sdba2 = 0x00000000, | |
| /* SDODT[0:1]: 100k pull-up, 40 ohm */ | |
| .dram_sdodt0 = 0x00003030, | |
| .dram_sdodt1 = 0x00003030, | |
| /* SDQS[0:7]: Differential input, 40 ohm */ | |
| .dram_sdqs0 = 0x00000030, | |
| .dram_sdqs1 = 0x00000030, | |
| .dram_sdqs2 = 0x00000030, | |
| .dram_sdqs3 = 0x00000030, | |
| .dram_sdqs4 = 0x00000030, | |
| .dram_sdqs5 = 0x00000030, | |
| .dram_sdqs6 = 0x00000030, | |
| .dram_sdqs7 = 0x00000030, | |
| /* DQM[0:7]: Differential input, 40 ohm */ | |
| .dram_dqm0 = 0x00020030, | |
| .dram_dqm1 = 0x00020030, | |
| .dram_dqm2 = 0x00020030, | |
| .dram_dqm3 = 0x00020030, | |
| .dram_dqm4 = 0x00020030, | |
| .dram_dqm5 = 0x00020030, | |
| .dram_dqm6 = 0x00020030, | |
| .dram_dqm7 = 0x00020030, | |
| }; | |
| /* Configure MX6Q/DUAL mmdc GRP io registers */ | |
| struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = { | |
| /* DDR3 */ | |
| .grp_ddr_type = 0x000c0000, | |
| .grp_ddrmode_ctl = 0x00020000, | |
| /* disable DDR pullups */ | |
| .grp_ddrpke = 0x00000000, | |
| /* ADDR[00:16], SDBA[0:1]: 40 ohm */ | |
| .grp_addds = 0x00000030, | |
| /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */ | |
| .grp_ctlds = 0x00000030, | |
| /* DATA[00:63]: Differential input, 40 ohm */ | |
| .grp_ddrmode = 0x00020000, | |
| .grp_b0ds = 0x00000030, | |
| .grp_b1ds = 0x00000030, | |
| .grp_b2ds = 0x00000030, | |
| .grp_b3ds = 0x00000030, | |
| .grp_b4ds = 0x00000030, | |
| .grp_b5ds = 0x00000030, | |
| .grp_b6ds = 0x00000030, | |
| .grp_b7ds = 0x00000030, | |
| }; | |
| /* MT41K256M16HA-125 */ | |
| static struct mx6_ddr3_cfg mt41k256m16ha_125 = { | |
| .mem_speed = 1600, | |
| .density = 4, /* 4Gbit */ | |
| .width = 16, | |
| .banks = 8, | |
| .rowaddr = 15, | |
| .coladdr = 10, | |
| .pagesz = 2, | |
| .trcd = 1375, | |
| .trcmin = 4875, | |
| .trasmin = 3500, | |
| }; | |
| /* | |
| * Values from running the Freescale DDR stress tool via USB | |
| */ | |
| static struct mx6_mmdc_calibration mx6dq_mmdc_calib = { | |
| /* write leveling calibration determine */ | |
| .p0_mpwldectrl0 = 0x0044004E, | |
| .p0_mpwldectrl1 = 0x001F0023, | |
| /* Read DQS Gating calibration */ | |
| .p0_mpdgctrl0 = 0x02480248, | |
| .p0_mpdgctrl1 = 0x0210021C, | |
| /* Read Calibration: DQS delay relative to DQ read access */ | |
| .p0_mprddlctl = 0x42444444, | |
| /* Write Calibration: DQ/DM delay relative to DQS write access */ | |
| .p0_mpwrdlctl = 0x36322C32, | |
| }; | |
| static void spl_dram_init(int width) | |
| { | |
| struct mx6_ddr3_cfg *mem = &mt41k256m16ha_125; | |
| struct mx6_ddr_sysinfo sysinfo = { | |
| /* width of data bus:0=16,1=32,2=64 */ | |
| .dsize = width / 32, | |
| /* config for full 4GB range so that get_mem_size() works */ | |
| .cs_density = 32, /* 32Gb per CS */ | |
| /* single chip select */ | |
| .ncs = 1, | |
| .cs1_mirror = 1, | |
| .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */ | |
| #ifdef RTT_NOM_120OHM | |
| .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */ | |
| #else | |
| .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */ | |
| #endif | |
| .walat = 0, /* Write additional latency */ | |
| .ralat = 5, /* Read additional latency */ | |
| .mif3_mode = 3, /* Command prediction working mode */ | |
| .bi_on = 1, /* Bank interleaving enabled */ | |
| .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ | |
| .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ | |
| .ddr_type = DDR_TYPE_DDR3, | |
| .refsel = 1, /* Refresh cycles at 32KHz */ | |
| .refr = 7, /* 8 refresh commands per refresh cycle */ | |
| }; | |
| mx6sdl_dram_iocfg(width, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs); | |
| mx6_dram_cfg(&sysinfo, &mx6dq_mmdc_calib, mem); | |
| } | |
| /* | |
| * Called from C runtime startup code (arch/arm/lib/crt0.S:_main) | |
| * - we have a stack and a place to store GD, both in SRAM | |
| * - no variable global data is available | |
| */ | |
| void board_init_f(ulong dummy) | |
| { | |
| /* Setup AIPS and disable watchdog */ | |
| arch_cpu_init(); | |
| ccgr_init(); | |
| gpr_init(); | |
| /* UART iomux */ | |
| board_early_init_f(); | |
| /* Setup GP timer */ | |
| timer_init(); | |
| /* UART clocks enabled and gd valid - init serial console */ | |
| preloader_console_init(); | |
| /* Init DDR with 32bit width */ | |
| spl_dram_init(32); | |
| /* Clear the BSS */ | |
| memset(__bss_start, 0, __bss_end - __bss_start); | |
| /* | |
| * Setup enet related MUXing early to give the PHY | |
| * some time to wake-up from reset | |
| */ | |
| platinum_setup_enet(); | |
| /* load/boot image from boot device */ | |
| board_init_r(NULL, 0); | |
| } |