blob: 125947118ec3ac2b00dbed512465070c0d0ad648 [file] [log] [blame]
/*
* board/amlogic/gxtvbb_skt_v1/gxtvbb_skt_v1.c
*
* Copyright (C) 2015 Amlogic, Inc. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
*/
#include <common.h>
#include <malloc.h>
#include <errno.h>
#include <environment.h>
#include <fdt_support.h>
#include <libfdt.h>
#ifdef CONFIG_SYS_I2C_AML
#include <aml_i2c.h>
#include <asm/arch/secure_apb.h>
#include <asm/arch/io.h>
#endif
#include <amlogic/canvas.h>
#ifdef CONFIG_AML_VPU
#include <vpu.h>
#endif
#include <vpp.h>
#ifdef CONFIG_AML_V2_FACTORY_BURN
#include <amlogic/aml_v2_burning.h>
#endif// #ifdef CONFIG_AML_V2_FACTORY_BURN
#ifdef CONFIG_AML_HDMITX20
#include <amlogic/hdmi.h>
#endif
#include <asm/arch/eth_setup.h>
#include <phy.h>
#ifdef CONFIG_AML_LCD
#include <amlogic/aml_lcd.h>
#endif
DECLARE_GLOBAL_DATA_PTR;
//new static eth setup
struct eth_board_socket* eth_board_skt;
int serial_set_pin_port(unsigned long port_base)
{
//UART in "Always On Module"
//GPIOAO_0==tx,GPIOAO_1==rx
//setbits_le32(P_AO_RTI_PIN_MUX_REG,3<<11);
return 0;
}
int dram_init(void)
{
gd->ram_size = PHYS_SDRAM_1_SIZE;
return 0;
}
/* secondary_boot_func
* this function should be write with asm, here, is is only for compiling pass
* */
void secondary_boot_func(void)
{
}
#ifdef CONFIG_AML_PMU4
#define AML1220_ADDR 0x35
#define AML1220_ANALOG_ADDR 0x20
unsigned int pmu4_analog_reg[15] = {
0x00, 0x00, 0x00, 0x00, 0x00, /* Reg 0x20 - 0x24 */
0x00, 0x00, 0x00, 0x00, 0x51, /* Reg 0x25 - 0x29 */
0x42, 0x00, 0x42, 0x41, 0x02 /* Reg 0x2a - 0x2e */
};
#define PMU4_ANALOG_REG_LEN ARRAY_SIZE(pmu4_analog_reg)
int aml_pmu4_read(int add, uint8_t *val)
{
int ret;
uint8_t buf[2] = { };
struct i2c_msg msg[] = {
{
.addr = AML1220_ADDR,
.flags = 0,
.len = sizeof(buf),
.buf = buf,
}
,
{
.addr = AML1220_ADDR,
.flags = I2C_M_RD,
.len = 1,
.buf = val,
}
};
buf[0] = add & 0xff;
buf[1] = (add >> 8) & 0x0f;
ret = aml_i2c_xfer(msg, 2);
if (ret < 0) {
printf("%s: i2c transfer failed, ret:%d\n", __func__, ret);
return ret;
}
return 0;
}
int aml_pmu4_write(int32_t add, uint8_t val)
{
int ret;
uint8_t buf[3] = { };
struct i2c_msg msg[] = {
{
.addr = AML1220_ADDR,
.flags = 0,
.len = sizeof(buf),
.buf = buf,
}
};
buf[0] = add & 0xff;
buf[1] = (add >> 8) & 0x0f;
buf[2] = val & 0xff;
ret = aml_i2c_xfer(msg, 1);
if (ret < 0) {
printf("%s: i2c transfer failed, ret:%d\n", __func__, ret);
return ret;
}
return 0;
}
void pmu4_phy_config(void)
{
#if 0
int i;
uint8_t value;
int data;
uint8_t data_lo;
uint8_t data_hi;
#endif
/* eth ldo */
aml_pmu4_write(0x04, 0x01);
aml_pmu4_write(0x05, 0x01);
mdelay(10);
/* pinmux */
aml_pmu4_write(0x2c, 0x51);
aml_pmu4_write(0x2d, 0x41);
aml_pmu4_write(0x20, 0x0);
aml_pmu4_write(0x21, 0x3);
#ifdef EXT_CLK
aml_pmu4_write(0x14, 0x01);
#else
aml_pmu4_write(0x14, 0x00);
#endif
aml_pmu4_write(0x15, 0x3f);
/* pll */
aml_pmu4_write(0x78, 0x06);
aml_pmu4_write(0x79, 0x05);
aml_pmu4_write(0x7a, 0xa1);
aml_pmu4_write(0x7b, 0xac);
aml_pmu4_write(0x7c, 0x5b);
aml_pmu4_write(0x7d, 0xa0);
aml_pmu4_write(0x7e, 0x20);
aml_pmu4_write(0x7f, 0x49);
aml_pmu4_write(0x80, 0xd6);
aml_pmu4_write(0x81, 0x0b);
aml_pmu4_write(0x82, 0xd1);
aml_pmu4_write(0x83, 0x00);
aml_pmu4_write(0x84, 0x00);
aml_pmu4_write(0x85, 0x00);
/*cfg4- --- cfg 45 */
aml_pmu4_write(0x88, 0x0);
aml_pmu4_write(0x89, 0x0);
aml_pmu4_write(0x8A, 0x22);
aml_pmu4_write(0x8B, 0x01);
aml_pmu4_write(0x8C, 0xd0);
aml_pmu4_write(0x8D, 0x01);
aml_pmu4_write(0x8E, 0x00);
aml_pmu4_write(0x93, 0x81);
/* pmu4 phyid = 20142014 */
aml_pmu4_write(0x94, 0x14);
aml_pmu4_write(0x95, 0x20);
aml_pmu4_write(0x96, 0x14);
aml_pmu4_write(0x97, 0x20);
/*phyadd & mode */
#ifdef EXT_CLK
aml_pmu4_write(0x98, 0x73);
#else
aml_pmu4_write(0x98, 0x47);
#endif
aml_pmu4_write(0x99, 0x61);
aml_pmu4_write(0x9a, 0x07);
aml_pmu4_write(0x04, 0x01);
aml_pmu4_write(0x05, 0x01);
#if 0
value = 0;
pr_info("--------> read 0x9c\n");
while ((value & 0x01) == 0)
aml_pmu4_read(0x9c, &value);
pr_info("----2----> read 0x9c over!\n");
#endif
aml_pmu4_write(0x9b, 0x00);
aml_pmu4_write(0x9b, 0x80);
aml_pmu4_write(0x9b, 0x00);
#if 0
printf("phy init though i2c done\n");
for (i = 0; i < 0xb0; i++) {
aml_pmu4_read(i, &value);
printf(" i2c[%x]=0x%x\n", i, value);
}
printf("phy reg dump though i2c:\n");
for (i = 0; i < 0x20; i++) {
aml_pmu4_write(0xa6, i);
aml_pmu4_read(0xa7, &data_lo);
aml_pmu4_read(0xa8, &data_hi);
data = (data_hi << 8) | data_lo;
printf(" phy[%x]=0x%x\n", i, data);
}
#endif
}
static int aml_pmu4_reg_init(unsigned int reg_base, unsigned int *val,
unsigned int reg_len)
{
int ret = 0;
unsigned int i = 0;
for (i = 0; i < reg_len; i++) {
ret = aml_pmu4_write(reg_base + i, val[i]);
if (ret < 0)
return ret;
}
return 0;
}
static int aml_pmu4_power_init(void)
{
int ret;
/* pmu4 analog register init */
ret = aml_pmu4_reg_init(AML1220_ANALOG_ADDR, &pmu4_analog_reg[0],
PMU4_ANALOG_REG_LEN);
if (ret < 0)
return ret;
pmu4_phy_config();
return 0;
}
void setup_pmu4(void)
{
aml_pmu4_power_init();
}
#endif
static void setup_net_chip(void)
{
eth_aml_reg0_t eth_reg0;
//setup ethernet clk need calibrate to configre
setbits_le32(P_PERIPHS_PIN_MUX_8, 0x1fff8000);
eth_reg0.d32 = 0;
eth_reg0.b.phy_intf_sel = 1;
eth_reg0.b.data_endian = 0;
eth_reg0.b.desc_endian = 0;
eth_reg0.b.rx_clk_rmii_invert = 0;
eth_reg0.b.rgmii_tx_clk_src = 0;
eth_reg0.b.rgmii_tx_clk_phase = 1;
eth_reg0.b.rgmii_tx_clk_ratio = 4;
eth_reg0.b.phy_ref_clk_enable = 1;
eth_reg0.b.clk_rmii_i_invert = 0;
eth_reg0.b.clk_en = 1;
eth_reg0.b.adj_enable = 0;
eth_reg0.b.adj_setup = 0;
eth_reg0.b.adj_delay = 0;
eth_reg0.b.adj_skew = 0;
eth_reg0.b.cali_start = 0;
eth_reg0.b.cali_rise = 0;
eth_reg0.b.cali_sel = 0;
eth_reg0.b.rgmii_rx_reuse = 0;
eth_reg0.b.eth_urgent = 0;
setbits_le32(P_PREG_ETH_REG0, eth_reg0.d32);// rgmii mode
setbits_le32(P_PREG_ETH_REG1, 0x20000);// rx delay
setbits_le32(HHI_GCLK_MPEG1,1<<3);
/* power on memory */
clrbits_le32(HHI_MEM_PD_REG0, (1 << 3) | (1<<2));
#ifndef CONFIG_AML_PMU4
/* hardware reset ethernet phy : gpioz6 connect phyreset pin*/
clrbits_le32(PREG_PAD_GPIO3_EN_N, 1 << 6);
clrbits_le32(PREG_PAD_GPIO3_O, 1 << 6);
udelay(100000);
setbits_le32(PREG_PAD_GPIO3_O, 1 << 6);
#endif
}
extern int designware_initialize(ulong base_addr, u32 interface);
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_AML_PMU4
setup_pmu4();
#endif
setup_net_chip();
udelay(1000);
designware_initialize(ETH_BASE, PHY_INTERFACE_MODE_RGMII);
return 0;
}
#if CONFIG_AML_SD_EMMC
#include <mmc.h>
#include <asm/arch/sd_emmc.h>
static int sd_emmc_init(unsigned port)
{
switch (port)
{
case SDIO_PORT_A:
break;
case SDIO_PORT_B:
//todo add card detect
//setbits_le32(P_PREG_PAD_GPIO5_EN_N,1<<29);//CARD_6
break;
case SDIO_PORT_C:
//enable pull up
//clrbits_le32(P_PAD_PULL_UP_REG3, 0xff<<0);
break;
default:
break;
}
return cpu_sd_emmc_init(port);
}
extern unsigned sd_debug_board_1bit_flag;
static int sd_emmc_detect(unsigned port)
{
int ret;
switch (port) {
case SDIO_PORT_A:
break;
case SDIO_PORT_B:
setbits_le32(P_PREG_PAD_GPIO5_EN_N,1<<29);//CARD_6
ret=readl(P_PREG_PAD_GPIO5_I)&(1<<29)?0:1;
printf("ret = %d .",ret);
if ((readl(P_PERIPHS_PIN_MUX_8)&(3<<9))) { //if uart pinmux set, debug board in
if (!(readl(P_PREG_PAD_GPIO2_I)&(1<<24))) {
printf("sdio debug board detected, sd card with 1bit mode\n");
sd_debug_board_1bit_flag = 1;
}
else{
printf("sdio debug board detected, no sd card in\n");
sd_debug_board_1bit_flag = 0;
return 1;
}
}
break;
default:
break;
}
return 0;
}
static void sd_emmc_pwr_prepare(unsigned port)
{
cpu_sd_emmc_pwr_prepare(port);
}
static void sd_emmc_pwr_on(unsigned port)
{
switch (port)
{
case SDIO_PORT_A:
break;
case SDIO_PORT_B:
// clrbits_le32(P_PREG_PAD_GPIO5_O,(1<<31)); //CARD_8
// clrbits_le32(P_PREG_PAD_GPIO5_EN_N,(1<<31));
/// @todo NOT FINISH
break;
case SDIO_PORT_C:
break;
default:
break;
}
return;
}
static void sd_emmc_pwr_off(unsigned port)
{
/// @todo NOT FINISH
switch (port)
{
case SDIO_PORT_A:
break;
case SDIO_PORT_B:
// setbits_le32(P_PREG_PAD_GPIO5_O,(1<<31)); //CARD_8
// clrbits_le32(P_PREG_PAD_GPIO5_EN_N,(1<<31));
break;
case SDIO_PORT_C:
break;
default:
break;
}
return;
}
// #define CONFIG_TSD 1
static void board_mmc_register(unsigned port)
{
struct aml_card_sd_info *aml_priv=cpu_sd_emmc_get(port);
if (aml_priv == NULL)
return;
aml_priv->sd_emmc_init=sd_emmc_init;
aml_priv->sd_emmc_detect=sd_emmc_detect;
aml_priv->sd_emmc_pwr_off=sd_emmc_pwr_off;
aml_priv->sd_emmc_pwr_on=sd_emmc_pwr_on;
aml_priv->sd_emmc_pwr_prepare=sd_emmc_pwr_prepare;
aml_priv->desc_buf = malloc(NEWSD_MAX_DESC_MUN*(sizeof(struct sd_emmc_desc_info)));
if (NULL == aml_priv->desc_buf)
printf(" desc_buf Dma alloc Fail!\n");
else
printf("aml_priv->desc_buf = 0x%p\n",aml_priv->desc_buf);
sd_emmc_register(aml_priv);
}
int board_mmc_init(bd_t *bis)
{
#ifdef CONFIG_VLSI_EMULATOR
//board_mmc_register(SDIO_PORT_A);
#else
//board_mmc_register(SDIO_PORT_B);
#endif
board_mmc_register(SDIO_PORT_B);
board_mmc_register(SDIO_PORT_C);
// board_mmc_register(SDIO_PORT_B1);
return 0;
}
#ifdef CONFIG_SYS_I2C_AML
#if 1
static void board_i2c_set_pinmux(void){
/*********************************************/
/* | I2C_Master_AO |I2C_Slave | */
/*********************************************/
/* | I2C_SCK | I2C_SCK_SLAVE | */
/* GPIOAO_4 | [AO_PIN_MUX: 6] | [AO_PIN_MUX: 2] | */
/*********************************************/
/* | I2C_SDA | I2C_SDA_SLAVE | */
/* GPIOAO_5 | [AO_PIN_MUX: 5] | [AO_PIN_MUX: 1] | */
/*********************************************/
//disable all other pins which share with I2C_SDA_AO & I2C_SCK_AO
clrbits_le32(PERIPHS_PIN_MUX_7, (1<<19)|(1<<20));
//enable I2C MASTER AO pins
setbits_le32(PERIPHS_PIN_MUX_7,
((MESON_I2C_MASTER_B_GPIOH_3_BIT) | (MESON_I2C_MASTER_B_GPIOH_4_BIT)));
udelay(10);
};
#endif
struct aml_i2c_platform g_aml_i2c_plat = {
.wait_count = 1000000,
.wait_ack_interval = 5,
.wait_read_interval = 5,
.wait_xfer_interval = 5,
.master_no = AML_I2C_MASTER_B,
.use_pio = 0,
.master_i2c_speed = AML_I2C_SPPED_400K,
.master_b_pinmux = {
.scl_reg = (unsigned long)MESON_I2C_MASTER_B_GPIOH_4_REG,
.scl_bit = MESON_I2C_MASTER_B_GPIOH_4_BIT,
.sda_reg = (unsigned long)MESON_I2C_MASTER_B_GPIOH_3_REG,
.sda_bit = MESON_I2C_MASTER_B_GPIOH_3_BIT,
}
};
#if 1
static void board_i2c_init(void)
{
//set I2C pinmux with PCB board layout
board_i2c_set_pinmux();
//Amlogic I2C controller initialized
//note: it must be call before any I2C operation
aml_i2c_init();
udelay(10);
}
#endif
#endif
#endif
#if defined(CONFIG_BOARD_EARLY_INIT_F)
int board_early_init_f(void){
/*add board early init function here*/
return 0;
}
#endif
#ifdef CONFIG_USB_XHCI_AMLOGIC
#include <asm/arch/usb.h>
#include <asm/arch/gpio.h>
struct amlogic_usb_config g_usb_config_GXTVBB_skt={
CONFIG_GXTVBB_XHCI_BASE,
USB_ID_MODE_HARDWARE,
NULL,//gpio_set_vbus_power, //set_vbus_power
CONFIG_GXTVBB_USB_PHY2_BASE,
CONFIG_GXTVBB_USB_PHY3_BASE,
};
#endif /*CONFIG_USB_XHCI_AMLOGIC*/
#ifdef CONFIG_AML_HDMITX20
static void hdmi_tx_set_hdmi_5v(void)
{
}
#endif
int board_init(void)
{
#ifdef CONFIG_AML_V2_FACTORY_BURN
aml_try_factory_usb_burning(0, gd->bd);
#endif// #ifdef CONFIG_AML_V2_FACTORY_BURN
#ifdef CONFIG_USB_XHCI_AMLOGIC
board_usb_init(&g_usb_config_GXTVBB_skt,BOARD_USB_MODE_HOST);
#endif /*CONFIG_USB_XHCI_AMLOGIC*/
canvas_init();
#ifdef CONFIG_SYS_I2C_AML
// #ifdef 1
board_i2c_init();
// #endif /*CONFIG_AML_I2C*/
#endif
return 0;
}
#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void){
int ret;
//update env before anyone using it
run_command("get_rebootmode; echo reboot_mode=${reboot_mode}; "\
"if test ${reboot_mode} = factory_reset; then "\
"defenv_reserv aml_dt;setenv upgrade_step 2;save; fi;", 0);
run_command("if itest ${upgrade_step} == 1; then "\
"defenv_reserv; setenv upgrade_step 2; saveenv; fi;", 0);
/*add board late init function here*/
run_command("setenv fdt_high 0x20000000", 1);
run_command("setenv dtb_mem_addr 0x1000000", 1);
ret = run_command("store dtb read $dtb_mem_addr", 1);
if (ret) {
printf("%s(): [store dtb read $dtb_mem_addr] fail\n", __func__);
#ifdef CONFIG_DTB_MEM_ADDR
char cmd[64];
printf("load dtb to %x\n", CONFIG_DTB_MEM_ADDR);
sprintf(cmd, "store dtb read %x", CONFIG_DTB_MEM_ADDR);
ret = run_command(cmd, 1);
if (ret) {
printf("%s(): %s fail\n", __func__, cmd);
}
#endif
}
#ifdef CONFIG_AML_VPU
vpu_probe();
#endif
#ifdef CONFIG_AML_HDMITX20
hdmi_tx_set_hdmi_5v();
hdmi_tx_init();
#endif
#ifdef CONFIG_AML_LCD
lcd_probe();
#endif
vpp_init();
#ifdef CONFIG_AML_V2_FACTORY_BURN
/*aml_try_factory_sdcard_burning(0, gd->bd);*/
#endif// #ifdef CONFIG_AML_V2_FACTORY_BURN
return 0;
}
#endif
#ifdef CONFIG_AML_TINY_USBTOOL
int usb_get_update_result(void)
{
unsigned long upgrade_step;
upgrade_step = simple_strtoul (getenv ("upgrade_step"), NULL, 16);
printf("upgrade_step = %d\n", (int)upgrade_step);
if (upgrade_step == 1)
{
run_command("defenv", 1);
run_command("setenv upgrade_step 2", 1);
run_command("saveenv", 1);
return 0;
}
else
{
return -1;
}
}
#endif
phys_size_t get_effective_memsize(void)
{
// >>16 -> MB, <<20 -> real size, so >>16<<20 = <<4
#if defined(CONFIG_SYS_MEM_TOP_HIDE)
return (((readl(AO_SEC_GP_CFG0)) & 0xFFFF0000) << 4) - CONFIG_SYS_MEM_TOP_HIDE;
#else
return (((readl(AO_SEC_GP_CFG0)) & 0xFFFF0000) << 4);
#endif
}
#ifdef CONFIG_MULTI_DTB
int checkhw(char * name)
{
unsigned int boardid = 0;
char loc_name[64] = {0};
boardid = (readl(AO_SEC_GP_CFG0)>>8)&0xff;
printf("%s: boardid = 0x%x\n", __func__,boardid);
switch (boardid) {
case 0:
strcpy(loc_name, "gxtvbb_p301_1g\0");
break;
case 8:
strcpy(loc_name, "gxtvbb_p300_2g\0");
break;
case 12:
strcpy(loc_name, "gxtvbb_skt_2g\0");
break;
default:
printf("boardid: 0x%x, multi-dt doesn't support\n", boardid);
//strcpy(loc_name, "gxb_p200_unsupport");
break;
}
strcpy(name, loc_name);
setenv("aml_dt", loc_name);
return 0;
}
#endif
const char * const _env_args_reserve_[] =
{
"aml_dt",
"firstboot",
NULL//Keep NULL be last to tell END
};