/*
 * (C) Copyright 2001-2003
 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <command.h>
#include <malloc.h>

DECLARE_GLOBAL_DATA_PTR;

int board_early_init_f (void)
{
	/*
	 * IRQ 0-15  405GP internally generated; active high; level sensitive
	 * IRQ 16    405GP internally generated; active low; level sensitive
	 * IRQ 17-24 RESERVED
	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
	 */
	mtdcr(UIC0SR, 0xFFFFFFFF);       /* clear all ints */
	mtdcr(UIC0ER, 0x00000000);       /* disable all ints */
	mtdcr(UIC0CR, 0x00000000);       /* set all to be non-critical*/
	mtdcr(UIC0PR, 0xFFFFFF80);       /* set int polarities */
	mtdcr(UIC0TR, 0x10000000);       /* set int trigger levels */
	mtdcr(UIC0VCR, 0x00000001);      /* set vect base=0,INT0 highest priority*/
	mtdcr(UIC0SR, 0xFFFFFFFF);       /* clear all ints */

	/*
	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
	 */
	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */

	/*
	 * Reset CPLD via GPIO13 (CS4) pin
	 */
	out_be32((void *)GPIO0_OR,
		 in_be32((void *)GPIO0_OR) & ~(0x80000000 >> 13));
	udelay(1000); /* wait 1ms */
	out_be32((void *)GPIO0_OR,
		 in_be32((void *)GPIO0_OR) | (0x80000000 >> 13));
	udelay(1000); /* wait 1ms */

	return 0;
}

int misc_init_r (void)
{
	/* adjust flash start and offset */
	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
	gd->bd->bi_flashoffset = 0;

	return (0);
}


/*
 * Check Board Identity:
 */

int checkboard (void)
{
	char str[64];
	int i = getenv_f("serial#", str, sizeof(str));
	unsigned char trans[16] = {0x0,0x8,0x4,0xc,0x2,0xa,0x6,0xe,
				   0x1,0x9,0x5,0xd,0x3,0xb,0x7,0xf};
	unsigned char id1, id2, rev;

	puts ("Board: ");

	if (i == -1)
		puts ("### No HW ID - assuming DP405");
	else
		puts(str);

	id1 = trans[(~(in_be32((void *)GPIO0_IR) >> 5)) & 0x0000000f];
	id2 = trans[(~(in_be32((void *)GPIO0_IR) >> 9)) & 0x0000000f];

	rev = in_8((void *)0xf0001000);
	if (rev & 0x10) /* old DP405 compatibility */
		rev = in_8((void *)0xf0000800);

	switch (rev & 0xc0) {
	case 0x00:
		puts(" (HW=DP405");
		break;
	case 0x80:
		puts(" (HW=DP405/CO");
		break;
	case 0xc0:
		puts(" (HW=DN405");
		break;
	}
	printf(", ID=0x%1X%1X, PLD=0x%02X", id2, id1, rev & 0x0f);

	if ((rev & 0xc0) == 0xc0) {
		printf(", C5V=%s",
		       in_be32((void *)GPIO0_IR) & 0x40000000 ? "off" : "on");
	}
	puts(")\n");

	return 0;
}