| /* | |
| * (C) Copyright 2010-2013 | |
| * NVIDIA Corporation <www.nvidia.com> | |
| * | |
| * SPDX-License-Identifier: GPL-2.0+ | |
| */ | |
| #include <common.h> | |
| #include <dm.h> | |
| #include <asm/arch/pinmux.h> | |
| #include <asm/arch/gp_padctrl.h> | |
| #include <asm/arch/gpio.h> | |
| #include <asm/gpio.h> | |
| #include "pinmux-config-cardhu.h" | |
| #include <i2c.h> | |
| #include <netdev.h> | |
| #define PMU_I2C_ADDRESS 0x2D | |
| #define MAX_I2C_RETRY 3 | |
| /* | |
| * Routine: pinmux_init | |
| * Description: Do individual peripheral pinmux configs | |
| */ | |
| void pinmux_init(void) | |
| { | |
| pinmux_config_pingrp_table(tegra3_pinmux_common, | |
| ARRAY_SIZE(tegra3_pinmux_common)); | |
| pinmux_config_pingrp_table(unused_pins_lowpower, | |
| ARRAY_SIZE(unused_pins_lowpower)); | |
| /* Initialize any non-default pad configs (APB_MISC_GP regs) */ | |
| pinmux_config_drvgrp_table(cardhu_padctrl, ARRAY_SIZE(cardhu_padctrl)); | |
| } | |
| #if defined(CONFIG_TEGRA_MMC) | |
| /* | |
| * Do I2C/PMU writes to bring up SD card bus power | |
| * | |
| */ | |
| void board_sdmmc_voltage_init(void) | |
| { | |
| struct udevice *dev; | |
| uchar reg, data_buffer[1]; | |
| int ret; | |
| int i; | |
| ret = i2c_get_chip_for_busnum(0, PMU_I2C_ADDRESS, &dev); | |
| if (ret) { | |
| debug("%s: Cannot find PMIC I2C chip\n", __func__); | |
| return; | |
| } | |
| /* TPS659110: LDO5_REG = 3.3v, ACTIVE to SDMMC1 */ | |
| data_buffer[0] = 0x65; | |
| reg = 0x32; | |
| for (i = 0; i < MAX_I2C_RETRY; ++i) { | |
| if (i2c_write(dev, reg, data_buffer, 1)) | |
| udelay(100); | |
| } | |
| /* TPS659110: GPIO7_REG = PDEN, output a 1 to EN_3V3_SYS */ | |
| data_buffer[0] = 0x09; | |
| reg = 0x67; | |
| for (i = 0; i < MAX_I2C_RETRY; ++i) { | |
| if (i2c_write(dev, reg, data_buffer, 1)) | |
| udelay(100); | |
| } | |
| } | |
| /* | |
| * Routine: pin_mux_mmc | |
| * Description: setup the MMC muxes, power rails, etc. | |
| */ | |
| void pin_mux_mmc(void) | |
| { | |
| /* | |
| * NOTE: We don't do mmc-specific pin muxes here. | |
| * They were done globally in pinmux_init(). | |
| */ | |
| /* Bring up the SDIO1 power rail */ | |
| board_sdmmc_voltage_init(); | |
| } | |
| #endif /* MMC */ | |
| #ifdef CONFIG_PCI_TEGRA | |
| int tegra_pcie_board_init(void) | |
| { | |
| struct udevice *dev; | |
| u8 addr, data[1]; | |
| int err; | |
| err = i2c_get_chip_for_busnum(0, PMU_I2C_ADDRESS, &dev); | |
| if (err) { | |
| debug("failed to find PMU bus\n"); | |
| return err; | |
| } | |
| /* TPS659110: LDO1_REG = 1.05V, ACTIVE */ | |
| data[0] = 0x15; | |
| addr = 0x30; | |
| err = i2c_write(dev, addr, data, 1); | |
| if (err) { | |
| debug("failed to set VDD supply\n"); | |
| return err; | |
| } | |
| /* GPIO: PEX = 3.3V */ | |
| err = gpio_request(GPIO_PL7, "PEX"); | |
| if (err < 0) | |
| return err; | |
| gpio_direction_output(GPIO_PL7, 1); | |
| /* TPS659110: LDO2_REG = 1.05V, ACTIVE */ | |
| data[0] = 0x15; | |
| addr = 0x31; | |
| err = i2c_write(dev, addr, data, 1); | |
| if (err) { | |
| debug("failed to set AVDD supply\n"); | |
| return err; | |
| } | |
| return 0; | |
| } | |
| int board_eth_init(bd_t *bis) | |
| { | |
| return pci_eth_init(bis); | |
| } | |
| #endif /* PCI */ |