| /* | |
| * Copyright (C) 2012 Renesas Solutions Corp. | |
| * | |
| * SPDX-License-Identifier: GPL-2.0+ | |
| */ | |
| #include <common.h> | |
| #include <malloc.h> | |
| #include <asm/processor.h> | |
| #include <asm/io.h> | |
| #include <asm/mmc.h> | |
| #include <spi.h> | |
| #include <spi_flash.h> | |
| int checkboard(void) | |
| { | |
| puts("BOARD: SH7752 evaluation board (R0P7752C00000RZ)\n"); | |
| return 0; | |
| } | |
| static void init_gpio(void) | |
| { | |
| struct gpio_regs *gpio = GPIO_BASE; | |
| struct sermux_regs *sermux = SERMUX_BASE; | |
| /* GPIO */ | |
| writew(0x0000, &gpio->pacr); /* GETHER */ | |
| writew(0x0001, &gpio->pbcr); /* INTC */ | |
| writew(0x0000, &gpio->pccr); /* PWMU, INTC */ | |
| writew(0xeaff, &gpio->pecr); /* GPIO */ | |
| writew(0x0000, &gpio->pfcr); /* WDT */ | |
| writew(0x0000, &gpio->phcr); /* SPI1 */ | |
| writew(0x0000, &gpio->picr); /* SDHI */ | |
| writew(0x0003, &gpio->pkcr); /* SerMux */ | |
| writew(0x0000, &gpio->plcr); /* SerMux */ | |
| writew(0x0000, &gpio->pmcr); /* RIIC */ | |
| writew(0x0000, &gpio->pncr); /* USB, SGPIO */ | |
| writew(0x0000, &gpio->pocr); /* SGPIO */ | |
| writew(0xd555, &gpio->pqcr); /* GPIO */ | |
| writew(0x0000, &gpio->prcr); /* RIIC */ | |
| writew(0x0000, &gpio->pscr); /* RIIC */ | |
| writeb(0x00, &gpio->pudr); | |
| writew(0x5555, &gpio->pucr); /* Debug LED */ | |
| writew(0x0000, &gpio->pvcr); /* RSPI */ | |
| writew(0x0000, &gpio->pwcr); /* EVC */ | |
| writew(0x0000, &gpio->pxcr); /* LBSC */ | |
| writew(0x0000, &gpio->pycr); /* LBSC */ | |
| writew(0x0000, &gpio->pzcr); /* eMMC */ | |
| writew(0xfe00, &gpio->psel0); | |
| writew(0xff00, &gpio->psel3); | |
| writew(0x771f, &gpio->psel4); | |
| writew(0x00ff, &gpio->psel6); | |
| writew(0xfc00, &gpio->psel7); | |
| writeb(0x10, &sermux->smr0); /* SMR0: SerMux mode 0 */ | |
| } | |
| static void init_usb_phy(void) | |
| { | |
| struct usb_common_regs *common0 = USB0_COMMON_BASE; | |
| struct usb_common_regs *common1 = USB1_COMMON_BASE; | |
| struct usb0_phy_regs *phy = USB0_PHY_BASE; | |
| struct usb1_port_regs *port = USB1_PORT_BASE; | |
| struct usb1_alignment_regs *align = USB1_ALIGNMENT_BASE; | |
| writew(0x0100, &phy->reset); /* set reset */ | |
| /* port0 = USB0, port1 = USB1 */ | |
| writew(0x0002, &phy->portsel); | |
| writel(0x0001, &port->port1sel); /* port1 = Host */ | |
| writew(0x0111, &phy->reset); /* clear reset */ | |
| writew(0x4000, &common0->suspmode); | |
| writew(0x4000, &common1->suspmode); | |
| #if defined(__LITTLE_ENDIAN) | |
| writel(0x00000000, &align->ehcidatac); | |
| writel(0x00000000, &align->ohcidatac); | |
| #endif | |
| } | |
| static void init_gether_mdio(void) | |
| { | |
| struct gpio_regs *gpio = GPIO_BASE; | |
| writew(readw(&gpio->pgcr) | 0x0004, &gpio->pgcr); | |
| writeb(readb(&gpio->pgdr) | 0x02, &gpio->pgdr); /* Use ET0-MDIO */ | |
| } | |
| static void set_mac_to_sh_giga_eth_register(int channel, char *mac_string) | |
| { | |
| struct ether_mac_regs *ether; | |
| unsigned char mac[6]; | |
| unsigned long val; | |
| eth_parse_enetaddr(mac_string, mac); | |
| if (!channel) | |
| ether = GETHER0_MAC_BASE; | |
| else | |
| ether = GETHER1_MAC_BASE; | |
| val = (mac[0] << 24) | (mac[1] << 16) | (mac[2] << 8) | mac[3]; | |
| writel(val, ðer->mahr); | |
| val = (mac[4] << 8) | mac[5]; | |
| writel(val, ðer->malr); | |
| } | |
| /***************************************************************** | |
| * This PMB must be set on this timing. The lowlevel_init is run on | |
| * Area 0(phys 0x00000000), so we have to map it. | |
| * | |
| * The new PMB table is following: | |
| * ent virt phys v sz c wt | |
| * 0 0xa0000000 0x40000000 1 128M 0 1 | |
| * 1 0xa8000000 0x48000000 1 128M 0 1 | |
| * 2 0xb0000000 0x50000000 1 128M 0 1 | |
| * 3 0xb8000000 0x58000000 1 128M 0 1 | |
| * 4 0x80000000 0x40000000 1 128M 1 1 | |
| * 5 0x88000000 0x48000000 1 128M 1 1 | |
| * 6 0x90000000 0x50000000 1 128M 1 1 | |
| * 7 0x98000000 0x58000000 1 128M 1 1 | |
| */ | |
| static void set_pmb_on_board_init(void) | |
| { | |
| struct mmu_regs *mmu = MMU_BASE; | |
| /* clear ITLB */ | |
| writel(0x00000004, &mmu->mmucr); | |
| /* delete PMB for SPIBOOT */ | |
| writel(0, PMB_ADDR_BASE(0)); | |
| writel(0, PMB_DATA_BASE(0)); | |
| /* add PMB for SDRAM(0x40000000 - 0x47ffffff) */ | |
| /* ppn ub v s1 s0 c wt */ | |
| writel(mk_pmb_addr_val(0xa0), PMB_ADDR_BASE(0)); | |
| writel(mk_pmb_data_val(0x40, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(0)); | |
| writel(mk_pmb_addr_val(0xb0), PMB_ADDR_BASE(2)); | |
| writel(mk_pmb_data_val(0x50, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(2)); | |
| writel(mk_pmb_addr_val(0xb8), PMB_ADDR_BASE(3)); | |
| writel(mk_pmb_data_val(0x58, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(3)); | |
| writel(mk_pmb_addr_val(0x80), PMB_ADDR_BASE(4)); | |
| writel(mk_pmb_data_val(0x40, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(4)); | |
| writel(mk_pmb_addr_val(0x90), PMB_ADDR_BASE(6)); | |
| writel(mk_pmb_data_val(0x50, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(6)); | |
| writel(mk_pmb_addr_val(0x98), PMB_ADDR_BASE(7)); | |
| writel(mk_pmb_data_val(0x58, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(7)); | |
| } | |
| int board_init(void) | |
| { | |
| init_gpio(); | |
| set_pmb_on_board_init(); | |
| init_usb_phy(); | |
| init_gether_mdio(); | |
| return 0; | |
| } | |
| int dram_init(void) | |
| { | |
| DECLARE_GLOBAL_DATA_PTR; | |
| gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE; | |
| gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE; | |
| printf("DRAM: %dMB\n", CONFIG_SYS_SDRAM_SIZE / (1024 * 1024)); | |
| return 0; | |
| } | |
| int board_mmc_init(bd_t *bis) | |
| { | |
| struct gpio_regs *gpio = GPIO_BASE; | |
| writew(readw(&gpio->pgcr) | 0x0040, &gpio->pgcr); | |
| writeb(readb(&gpio->pgdr) & ~0x08, &gpio->pgdr); /* Reset */ | |
| udelay(1); | |
| writeb(readb(&gpio->pgdr) | 0x08, &gpio->pgdr); /* Release reset */ | |
| udelay(200); | |
| return mmcif_mmc_init(); | |
| } | |
| static int get_sh_eth_mac_raw(unsigned char *buf, int size) | |
| { | |
| struct spi_flash *spi; | |
| int ret; | |
| spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3); | |
| if (spi == NULL) { | |
| printf("%s: spi_flash probe failed.\n", __func__); | |
| return 1; | |
| } | |
| ret = spi_flash_read(spi, SH7752EVB_ETHERNET_MAC_BASE, size, buf); | |
| if (ret) { | |
| printf("%s: spi_flash read failed.\n", __func__); | |
| spi_flash_free(spi); | |
| return 1; | |
| } | |
| spi_flash_free(spi); | |
| return 0; | |
| } | |
| static int get_sh_eth_mac(int channel, char *mac_string, unsigned char *buf) | |
| { | |
| memcpy(mac_string, &buf[channel * (SH7752EVB_ETHERNET_MAC_SIZE + 1)], | |
| SH7752EVB_ETHERNET_MAC_SIZE); | |
| mac_string[SH7752EVB_ETHERNET_MAC_SIZE] = 0x00; /* terminate */ | |
| return 0; | |
| } | |
| static void init_ethernet_mac(void) | |
| { | |
| char mac_string[64]; | |
| char env_string[64]; | |
| int i; | |
| unsigned char *buf; | |
| buf = malloc(256); | |
| if (!buf) { | |
| printf("%s: malloc failed.\n", __func__); | |
| return; | |
| } | |
| get_sh_eth_mac_raw(buf, 256); | |
| /* Gigabit Ethernet */ | |
| for (i = 0; i < SH7752EVB_ETHERNET_NUM_CH; i++) { | |
| get_sh_eth_mac(i, mac_string, buf); | |
| if (i == 0) | |
| setenv("ethaddr", mac_string); | |
| else { | |
| sprintf(env_string, "eth%daddr", i); | |
| setenv(env_string, mac_string); | |
| } | |
| set_mac_to_sh_giga_eth_register(i, mac_string); | |
| } | |
| free(buf); | |
| } | |
| int board_late_init(void) | |
| { | |
| init_ethernet_mac(); | |
| return 0; | |
| } | |
| int do_write_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) | |
| { | |
| int i, ret; | |
| char mac_string[256]; | |
| struct spi_flash *spi; | |
| unsigned char *buf; | |
| if (argc != 3) { | |
| buf = malloc(256); | |
| if (!buf) { | |
| printf("%s: malloc failed.\n", __func__); | |
| return 1; | |
| } | |
| get_sh_eth_mac_raw(buf, 256); | |
| /* print current MAC address */ | |
| for (i = 0; i < SH7752EVB_ETHERNET_NUM_CH; i++) { | |
| get_sh_eth_mac(i, mac_string, buf); | |
| printf("GETHERC ch%d = %s\n", i, mac_string); | |
| } | |
| free(buf); | |
| return 0; | |
| } | |
| /* new setting */ | |
| memset(mac_string, 0xff, sizeof(mac_string)); | |
| sprintf(mac_string, "%s\t%s", | |
| argv[1], argv[2]); | |
| /* write MAC data to SPI rom */ | |
| spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3); | |
| if (!spi) { | |
| printf("%s: spi_flash probe failed.\n", __func__); | |
| return 1; | |
| } | |
| ret = spi_flash_erase(spi, SH7752EVB_ETHERNET_MAC_BASE_SPI, | |
| SH7752EVB_SPI_SECTOR_SIZE); | |
| if (ret) { | |
| printf("%s: spi_flash erase failed.\n", __func__); | |
| return 1; | |
| } | |
| ret = spi_flash_write(spi, SH7752EVB_ETHERNET_MAC_BASE_SPI, | |
| sizeof(mac_string), mac_string); | |
| if (ret) { | |
| printf("%s: spi_flash write failed.\n", __func__); | |
| spi_flash_free(spi); | |
| return 1; | |
| } | |
| spi_flash_free(spi); | |
| puts("The writing of the MAC address to SPI ROM was completed.\n"); | |
| return 0; | |
| } | |
| U_BOOT_CMD( | |
| write_mac, 3, 1, do_write_mac, | |
| "write MAC address for GETHERC", | |
| "[GETHERC ch0] [GETHERC ch1]\n" | |
| ); |