
/*
 * board/amlogic/txl_skt_v1/firmware/timing.c
 *
 * Copyright (C) 2015 Amlogic, Inc. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
 * more details.
 *
 * You should have received a copy of the GNU General Public License along
 * with this program; if not, write to the Free Software Foundation, Inc.,
 * 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
*/

#include <asm/arch/secure_apb.h>
#include <asm/arch/timing.h>
#include <asm/arch/ddr_define.h>


/* ddr config support multiple configs for boards which use same bootloader:
 * config steps:
 * 1. add a new data struct in __ddr_setting[]
 * 2. config correct board_id, ddr_type, freq, etc..
 */


/* CAUTION!! */
/* Confirm ddr configs with hardware designer,
 * if you don't know how to config, then don't edit it
 */

/* Key configs */
/*
 * board_id: check hardware adc config
 * dram_rank_config:
 *            #define CONFIG_DDR_CHL_AUTO					0xF
 *            #define CONFIG_DDR0_16BIT_CH0				0x1
 *            #define CONFIG_DDR0_16BIT_RANK01_CH0		0x4
 *            #define CONFIG_DDR0_32BIT_RANK0_CH0			0x2
 *            #define CONFIG_DDR0_32BIT_RANK01_CH01		0x3
 *            #define CONFIG_DDR0_32BIT_16BIT_RANK0_CH0	0x5
 *            #define CONFIG_DDR0_32BIT_16BIT_RANK01_CH0	0x6
 * DramType:
 *            #define CONFIG_DDR_TYPE_DDR3				0
 *            #define CONFIG_DDR_TYPE_DDR4				1
 *            #define CONFIG_DDR_TYPE_LPDDR4				2
 *            #define CONFIG_DDR_TYPE_LPDDR3				3
 * DRAMFreq:
 *            {pstate0, pstate1, pstate2, pstate3} //more than one pstate means use dynamic freq
 *
 */

ddr_set_t __ddr_setting[] __attribute__ ((section(".ddr_settings"))) = {
{
	//tl1 ref(T309) lpddr4
	.board_id				= CONFIG_BOARD_ID_MASK,
	.version				= 1,
	//.dram_rank_config		= CONFIG_DDR0_32BIT_RANK01_CH0,
	.dram_rank_config		= CONFIG_DDR0_32BIT_RANK0_CH0,
	.ddr_rfc_type			= DDR_RFC_TYPE_LPDDR4_8Gbx1,
	.DramType				= CONFIG_DDR_TYPE_LPDDR4,
	.DRAMFreq				= {1200, 0, 0, 0},
	.ddr_base_addr			= CFG_DDR_BASE_ADDR,
	.ddr_start_offset		= CFG_DDR_START_OFFSET,
	.DisabledDbyte			= 0xf0,
	.Is2Ttiming				= 0,
	.HdtCtrl				= 0xa,
	.dram_cs0_size_MB		= 0xffff,//1024,
	.dram_cs1_size_MB		= 0,//1024,
	.training_SequenceCtrl	= {0x131f,0x61}, //ddr3 0x21f 0x31f
	.phy_odt_config_rank	= {0x23,0x13}, //use 0x23 0x13  compatibility with 1rank and 2rank //targeting rank 0. [3:0] is used //for write ODT [7:4] is used for //read ODT
	.dfi_odt_config			= 0x0d0d,  //use 0d0d compatibility with 1rank and 2rank  //0808
	.PllBypassEn			= 0, //bit0-ps0,bit1-ps1
	.ddr_rdbi_wr_enable		= 0x3,
	.clk_drv_ohm			= 60,
	.cs_drv_ohm				= 40,
	.ac_drv_ohm				= 60,
	.soc_data_drv_ohm_p		= 48,
	.soc_data_drv_ohm_n		= 48,
	.soc_data_odt_ohm_p		= 0,
	.soc_data_odt_ohm_n		= 60,
	.dram_data_drv_ohm		= 48, //lpddr4 sdram only240/1-6
	.dram_data_odt_ohm		= 120,
	.dram_ac_odt_ohm		= 120,// 120,
	.lpddr4_dram_vout_voltage_1_3_2_5_setting   =0,///1, 1/3vddq     0 2/5 vddq
	.soc_clk_slew_rate		= 0x3ff,//0x253,
	.soc_cs_slew_rate		= 0x100,//0x253,
	.soc_ac_slew_rate		= 0x100,//0x253,
	.soc_data_slew_rate		= 0x1ff,
	.vref_output_permil		= 260,//200,
	.vref_receiver_permil	= 0,
	.vref_dram_permil		= 0,
	//.vref_reverse			= 0,
	//.ac_trace_delay			= {32-5,0,0,0,0,0,0x0,00},
	//.ac_pinmux				= {00,00},
	.ddr_dmc_remap			= {
							[0] = ( 5 |  6 << 5 |  7 << 10 |  8<< 15 | 9<< 20 | 10 << 25 ),
							[1] = ( 11|  0 << 5 |  0 << 10 | 15 << 15 | 16 << 20 | 17 << 25 ),
							[2] = ( 18| 19 << 5 | 20 << 10 | 21 << 15 | 22 << 20 | 23 << 25 ),
							[3] = ( 24| 25 << 5 | 26 << 10 | 27 << 15 | 28 << 20 | 29 << 25 ),
							[4] = ( 30| 12 << 5 | 13 << 10 |  14<< 15 |  0 << 20 |  0 << 25 ),
	},
	.ddr_lpddr34_ca_remap	= {00,00},
	//.ddr_lpddr34_dq_remap	= {4,5,6,7,0,2,3,1,  15,14,13,12,11,9,10,8, 4,5,6,7,0,2,3,1,  15,14,13,12,11,9,10,8,},
	.ddr_lpddr34_dq_remap	= {4,5,6,7,0,2,3,1,  15,14,13,12,11,9,10,8,   20,18,17,16,23,22,19,21,   30,31,25,24,26,28,29,27},
	.dram_rtt_nom_wr_park	= {00,00},
	.pll_ssc_mode			= (1<<20) | (1<<8) | (2<<4) | 0,//center_ssc_1000ppm
	.ddr_func				= DDR_FUNC,
	.magic					= DRAM_CFG_MAGIC,
	.diagnose				= CONFIG_DIAGNOSE_DISABLE,
	.bitTimeControl_2d		= 1,	//training time setting,=1,200ms;=7,2s
	.fast_boot[0]			= 1,
},
{
	/// tl1 ref(x301) ddr3
	.board_id				=CONFIG_BOARD_ID_MASK,
	.version				= 1,
	.dram_rank_config		= CONFIG_DDR0_32BIT_RANK01_CH0,
	.DramType				= CONFIG_DDR_TYPE_DDR3,
	.DRAMFreq				= {1008, 0, 0, 0},
	.ddr_base_addr			= CFG_DDR_BASE_ADDR,
	.ddr_start_offset		= CFG_DDR_START_OFFSET,
	.DisabledDbyte			= 0xf0,
	.Is2Ttiming				= 1,
	.HdtCtrl				= 0xc8,//0xC8,
	.dram_cs0_size_MB		= 0xffff,
	.dram_cs1_size_MB		= 0xffff,// 1024,
	.training_SequenceCtrl	= {0x31f,0}, //ddr3 0x21f 0x31f
	.phy_odt_config_rank	= {0x23,0x13}, //use 0x23 0x13  compatibility with 1rank and 2rank //targeting rank 0. [3:0] is used //for write ODT [7:4] is used for //read ODT
	.dfi_odt_config			= 0x0d0d,  //use 0d0d compatibility with 1rank and 2rank  //0808
	.PllBypassEn			= 0, //bit0-ps0,bit1-ps1
	.ddr_rdbi_wr_enable		= 0,
	.clk_drv_ohm			= 40,
	.cs_drv_ohm				= 40,
	.ac_drv_ohm				= 60,
	.soc_data_drv_ohm_p		= 40,
	.soc_data_drv_ohm_n		= 40,
	.soc_data_odt_ohm_p		= 48,//120, //48, ddr3 will use odt_ohm_p value
	.soc_data_odt_ohm_n		= 0,//120,
	.dram_data_drv_ohm		= 40, //ddr4 sdram only 34 or 48, skt board use 34 better
	.dram_data_odt_ohm		= 40,
	.dram_ac_odt_ohm		= 0,
	.dram_data_wr_odt_ohm	= 120,
	.soc_clk_slew_rate		= 0x300,
	.soc_cs_slew_rate		= 0x300,
	.soc_ac_slew_rate		= 0x300,
	.soc_data_slew_rate		= 0x200,
	.vref_output_permil		= 500,
	.vref_receiver_permil	= 500, //700,
	.vref_dram_permil		= 500, //700,
//	.vref_reverse			= 0,
//	.ac_trace_delay			= {32,32-10,32,32,32+10,32,32,32,32,32-10},
//	.ac_trace_delay			= {32-10,32-15,32,32,32,32,32,32,32,32-10},
	.ac_trace_delay			= {32-10,32+10,32,32,32,32,32+15,32+10,32+10,32-15},
	//{00,00},
	.ac_pinmux				= {00,00},
#if 1
	.ddr_dmc_remap			= {
							[0] = ( 5 |  7 << 5 |  8 << 10 |  9 << 15 | 10 << 20 | 11 << 25 ),
							[1] = ( 12|  0 << 5 |  0 << 10 | 14 << 15 | 15 << 20 | 16 << 25 ),
							[2] = ( 17| 18 << 5 | 19 << 10 | 21 << 15 | 22 << 20 | 23 << 25 ),
							[3] = ( 24| 25 << 5 | 26 << 10 | 27 << 15 | 28 << 20 | 29 << 25 ),
							[4] = ( 30| 13 << 5 | 20 << 10 |  6 << 15 |  0 << 20 |  0 << 25 ),
	},
#else
	//16bit
	.ddr_dmc_remap			= {
							[0] = ( 0 |  5 << 5 |  6<< 10 |  7 << 15 | 8 << 20 | 9 << 25 ),
							[1] = ( 10|  0 << 5 |  0 << 10 | 14 << 15 | 15 << 20 | 16 << 25 ),
							[2] = ( 17|( 18 << 5) |( 19 << 10) |( 20 << 15) |( 21 << 20) | (22 << 25 )),
							[3] = ( 23| 24 << 5 | 25 << 10 | 26 << 15 | 27 << 20 | 28 << 25 ),
							[4] = ( 29| 11<< 5 | 12 << 10 |  13<< 15 |  0 << 20 |  0 << 25 ),
	},
#endif
	.ddr_lpddr34_ca_remap	= {00,00},
	.ddr_lpddr34_dq_remap	= {00,00},
	.dram_rtt_nom_wr_park	= {00,00},


	.pll_ssc_mode			= (1<<20) | (1<<8) | (2<<4) | 0,//center_ssc_1000ppm
	.ddr_func				= DDR_FUNC,
	.magic					= DRAM_CFG_MAGIC,
	.fast_boot[0]			= 1,
},
//*/
{
	/* tl1 skt (x309) ddr4 */
	.board_id				= CONFIG_BOARD_ID_MASK,
	.version				= 1,
	.dram_rank_config		= CONFIG_DDR0_32BIT_RANK0_CH0,
	.DramType				= CONFIG_DDR_TYPE_DDR4,
	.DRAMFreq				= {1200, 0, 0, 0},
	.ddr_rfc_type			= DDR_RFC_TYPE_DDR4_2Gbx8,
	.ddr_base_addr			= CFG_DDR_BASE_ADDR,
	.ddr_start_offset		= CFG_DDR_START_OFFSET,
	.DisabledDbyte			= 0xf0,
	.Is2Ttiming				= 1,
	.HdtCtrl				= 0xC8,
	.dram_cs0_size_MB		= 0xffff,
	.dram_cs1_size_MB		= 0,
	.training_SequenceCtrl	= {0x31f,0x61}, //ddr3 0x21f 0x31f
	.phy_odt_config_rank	= {0x23,0x13}, //use 0x23 0x13  compatibility with 1rank and 2rank //targeting rank 0. [3:0] is used //for write ODT [7:4] is used for //read ODT
	.dfi_odt_config			= 0x0d0d,  //use 0d0d compatibility with 1rank and 2rank  //0808
	.PllBypassEn			= 0, //bit0-ps0,bit1-ps1
	.ddr_rdbi_wr_enable		= 0x1,//bit 0 read-dbi,bit 1 write dbi
	.clk_drv_ohm			= 40,
	.cs_drv_ohm				= 40,
	.ac_drv_ohm				= 40,
	.soc_data_drv_ohm_p		= 48,
	.soc_data_drv_ohm_n		= 48,
	.soc_data_odt_ohm_p		= 60,
	.soc_data_odt_ohm_n		= 0,
	.dram_data_drv_ohm		= 48,//48, //34, //ddr4 sdram only 34 or 48, skt board use 34 better
	.dram_data_odt_ohm		= 48, //60,
	.dram_ac_odt_ohm		= 0,
	.soc_clk_slew_rate		= 0x3ff,
	.soc_cs_slew_rate		= 0x3ff,
	.soc_ac_slew_rate		= 0x3ff,
	.soc_data_slew_rate		= 0x2ff,
	.vref_output_permil		= 500,
	.vref_receiver_permil	= 0,
	.vref_dram_permil		= 0,
	//.vref_reverse			= 0,
	//.ac_trace_delay			={0x0,0x0},// {0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40},
	.ac_trace_delay			= {32+10,32+10,32+10,32+10,32,32+10,32+10,32+10,32+10,32+10},
	.ddr_dmc_remap			= {
							[0] = ( 5 |  7 << 5 |  8 << 10 |  9 << 15 | 10 << 20 | 11 << 25 ),
							[1] = ( 12|  0 << 5 |  0 << 10 | 14 << 15 | 15 << 20 | 16 << 25 ),
							[2] = ( 17| 18 << 5 | 19 << 10 | 21 << 15 | 22 << 20 | 23 << 25 ),
							[3] = ( 24| 25 << 5 | 26 << 10 | 27 << 15 | 28 << 20 | 29 << 25 ),
							[4] = ( 30| 13 << 5 | 20 << 10 |  6 << 15 |  0 << 20 |  0 << 25 ),
	},
	.ddr_lpddr34_ca_remap	= {00,00},
	.ddr_lpddr34_dq_remap	= {00,00},
	.dram_rtt_nom_wr_park	= {00,00},

	/* pll ssc config:
	 *
	 *   pll_ssc_mode = (1<<20) | (1<<8) | ([strength] << 4) | [mode],
	 *      ppm = strength * 500
	 *      mode: 0=center, 1=up, 2=down
	 *
	 *   eg:
	 *     1. config 1000ppm center ss. then mode=0, strength=2
	 *        .pll_ssc_mode = (1<<20) | (1<<8) | (2 << 4) | 0,
	 *     2. config 3000ppm down ss. then mode=2, strength=6
	 *        .pll_ssc_mode = (1<<20) | (1<<8) | (6 << 4) | 2,
	 */
	.pll_ssc_mode			= (1<<20) | (1<<8) | (2<<4) | 0,//center_ssc_1000ppm
	.ddr_func				= DDR_FUNC,
	.magic					= DRAM_CFG_MAGIC,
	.slt_test_function={0x0,0x0},   //{0x1,0x0},enable slt 4 DRAMFreq test;{0x0,0x0},disable slt 4 DRAMFreq test;
	.fast_boot[0]			= 1,
},
/*
{
	// g12a skt (u209) ddr3
	.board_id				= CONFIG_BOARD_ID_MASK,
	.version				= 1,
	.dram_rank_config		= CONFIG_DDR0_32BIT_RANK0_CH0,
	.DramType				= CONFIG_DDR_TYPE_DDR3,
	.DRAMFreq				= {912, 0, 0, 0},
	.ddr_base_addr			= CFG_DDR_BASE_ADDR,
	.ddr_start_offset		= CFG_DDR_START_OFFSET,
	.DisabledDbyte			= 0xf0,
	.Is2Ttiming				= 1,
	.HdtCtrl				= 0x5,//0xC8,
	.dram_cs0_size_MB		= 0xffff,
	.dram_cs1_size_MB		= 0,// 1024,
	.training_SequenceCtrl	= {0x31f,0}, //ddr3 0x21f 0x31f
	.phy_odt_config_rank	= {0x23,0x13}, //use 0x23 0x13  compatibility with 1rank and 2rank //targeting rank 0. [3:0] is used //for write ODT [7:4] is used for //read ODT
	.dfi_odt_config			= 0x0d0d,  //use 0d0d compatibility with 1rank and 2rank  //0808
	.PllBypassEn			= 0, //bit0-ps0,bit1-ps1
	.ddr_rdbi_wr_enable		= 0,
	.clk_drv_ohm			= 40,
	.cs_drv_ohm				= 40,
	.ac_drv_ohm				= 40,
	.soc_data_drv_ohm_p		= 34,
	.soc_data_drv_ohm_n		= 34,
	.soc_data_odt_ohm_p		= 60, //48,
	.soc_data_odt_ohm_n		= 0,
	.dram_data_drv_ohm		= 34, //ddr4 sdram only 34 or 48, skt board use 34 better
	.dram_data_odt_ohm		= 60,
	.dram_ac_odt_ohm		= 0,
	.soc_clk_slew_rate		= 0x300,
	.soc_cs_slew_rate		= 0x300,
	.soc_ac_slew_rate		= 0x300,
	.soc_data_slew_rate		= 0x200,
	.vref_output_permil		= 500,
	.vref_receiver_permil	= 500, //700,
	.vref_dram_permil		= 500, //700,
//	.vref_reverse			= 0,
	.ac_trace_delay			= {0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40},
	//{00,00},
	.ac_pinmux				= {00,00},
#if 1
	.ddr_dmc_remap			= {
							[0] = ( 5 |  7 << 5 |  8 << 10 |  9 << 15 | 10 << 20 | 11 << 25 ),
							[1] = ( 12|  0 << 5 |  0 << 10 | 14 << 15 | 15 << 20 | 16 << 25 ),
							[2] = ( 17| 18 << 5 | 19 << 10 | 21 << 15 | 22 << 20 | 23 << 25 ),
							[3] = ( 24| 25 << 5 | 26 << 10 | 27 << 15 | 28 << 20 | 29 << 25 ),
							[4] = ( 30| 13 << 5 | 20 << 10 |  6 << 15 |  0 << 20 |  0 << 25 ),
	},
#else
	//16bit
	.ddr_dmc_remap			= {
							[0] = ( 0 |  5 << 5 |  6<< 10 |  7 << 15 | 8 << 20 | 9 << 25 ),
							[1] = ( 10|  0 << 5 |  0 << 10 | 14 << 15 | 15 << 20 | 16 << 25 ),
							[2] = ( 17|( 18 << 5) |( 19 << 10) |( 20 << 15) |( 21 << 20) | (22 << 25 )),
							[3] = ( 23| 24 << 5 | 25 << 10 | 26 << 15 | 27 << 20 | 28 << 25 ),
							[4] = ( 29| 11<< 5 | 12 << 10 |  13<< 15 |  0 << 20 |  0 << 25 ),
	},
#endif
	.ddr_lpddr34_ca_remap	= {00,00},
	.ddr_lpddr34_dq_remap	= {00,00},
	.dram_rtt_nom_wr_park	= {00,00},


	.pll_ssc_mode			= (1<<20) | (1<<8) | (2<<4) | 0,//center_ssc_1000ppm
	.ddr_func				= DDR_FUNC,
	.magic					= DRAM_CFG_MAGIC,
},

{
	//g12a skt (u209) lpddr4
	.board_id				= CONFIG_BOARD_ID_MASK,
	.version				= 1,
	//.dram_rank_config		= CONFIG_DDR0_32BIT_RANK01_CH0,
	.dram_rank_config		= CONFIG_DDR0_32BIT_RANK01_CH01,
	.ddr_rfc_type			= DDR_RFC_TYPE_LPDDR4_4Gbx1,
	.DramType				= CONFIG_DDR_TYPE_LPDDR4,
	.DRAMFreq				= {1392, 0, 0, 0},
	.ddr_base_addr			= CFG_DDR_BASE_ADDR,
	.ddr_start_offset		= CFG_DDR_START_OFFSET,
	.DisabledDbyte			= 0xf0,
	.Is2Ttiming				= 0,
	.HdtCtrl				= 0xa,
	.dram_cs0_size_MB		= 0xffff,//1024,
	.dram_cs1_size_MB		= 0xffff,//1024,
	.training_SequenceCtrl	= {0x131f,0x61}, //ddr3 0x21f 0x31f
	.phy_odt_config_rank	= {0x23,0x13}, //use 0x23 0x13  compatibility with 1rank and 2rank //targeting rank 0. [3:0] is used //for write ODT [7:4] is used for //read ODT
	.dfi_odt_config			= 0x0d0d,  //use 0d0d compatibility with 1rank and 2rank  //0808
	.PllBypassEn			= 0, //bit0-ps0,bit1-ps1
	.ddr_rdbi_wr_enable		= 0,
	.clk_drv_ohm			= 40,
	.cs_drv_ohm				= 40,
	.ac_drv_ohm				= 40,
	.soc_data_drv_ohm_p		= 40,
	.soc_data_drv_ohm_n		= 40,
	.soc_data_odt_ohm_p		= 0,
	.soc_data_odt_ohm_n		= 120,
	.dram_data_drv_ohm		= 40, //lpddr4 sdram only240/1-6
	.dram_data_odt_ohm		= 120,
	.dram_ac_odt_ohm		= 120,
	.soc_clk_slew_rate		= 0x3ff,//0x253,
	.soc_cs_slew_rate		= 0x100,//0x253,
	.soc_ac_slew_rate		= 0x100,//0x253,
	.soc_data_slew_rate		= 0x1ff,
	.vref_output_permil		= 350,//200,
	.vref_receiver_permil	= 200,
	.vref_dram_permil		= 350,
	//.vref_reverse			= 0,
	.ac_trace_delay			= {00,0x0,0,0,0,0,0x0,00},
	.ac_pinmux				= {00,00},
	.ddr_dmc_remap			= {
							[0] = ( 5 |  6 << 5 |  7 << 10 |  8<< 15 | 9<< 20 | 10 << 25 ),
							[1] = ( 11|  0 << 5 |  0 << 10 | 15 << 15 | 16 << 20 | 17 << 25 ),
							[2] = ( 18| 19 << 5 | 20 << 10 | 21 << 15 | 22 << 20 | 23 << 25 ),
							[3] = ( 24| 25 << 5 | 26 << 10 | 27 << 15 | 28 << 20 | 29 << 25 ),
							[4] = ( 30| 12 << 5 | 13 << 10 |  14<< 15 |  0 << 20 |  0 << 25 ),
	},
	.ddr_lpddr34_ca_remap	= {00,00},
	.ddr_lpddr34_dq_remap	= {3,2,0,1,7,6,5,4,14,13,12,15,8,9,11,10,20,21,22,23,16,17,19,18,24,25,28,26,31,30,27,29},
	.dram_rtt_nom_wr_park	= {00,00},
	.pll_ssc_mode			= (1<<20) | (1<<8) | (2<<4) | 0,//center_ssc_1000ppm
	.ddr_func				= DDR_FUNC,
	.magic					= DRAM_CFG_MAGIC,
	.diagnose				= CONFIG_DIAGNOSE_DISABLE,
},
{
	// g12a Y2 dongle
	.board_id				= CONFIG_BOARD_ID_MASK,
	.version				= 1,
	//.dram_rank_config		= CONFIG_DDR0_32BIT_RANK01_CH0,
	.dram_rank_config		= CONFIG_DDR0_32BIT_RANK0_CH01,
	.ddr_rfc_type			= DDR_RFC_TYPE_LPDDR4_4Gbx1,
	.DramType				= CONFIG_DDR_TYPE_LPDDR4,
	.DRAMFreq				= {1392, 0, 0, 0},
	.ddr_base_addr			= CFG_DDR_BASE_ADDR,
	.ddr_start_offset		= CFG_DDR_START_OFFSET,
	.DisabledDbyte			= 0xf0,
	.Is2Ttiming				= 0,
	.HdtCtrl				= 0xa,
	.dram_cs0_size_MB		= 1536,//1024,
	.dram_cs1_size_MB		= 0,//1024,
	.training_SequenceCtrl	= {0x131f,0x61}, //ddr3 0x21f 0x31f
	.phy_odt_config_rank	= {0x23,0x13}, //use 0x23 0x13  compatibility with 1rank and 2rank //targeting rank 0. [3:0] is used //for write ODT [7:4] is used for //read ODT
	.dfi_odt_config			= 0x0d0d,  //use 0d0d compatibility with 1rank and 2rank  //0808
	.PllBypassEn			= 0, //bit0-ps0,bit1-ps1
	.ddr_rdbi_wr_enable		= 0,
	.clk_drv_ohm			= 40,
	.cs_drv_ohm				= 40,
	.ac_drv_ohm				= 40,
	.soc_data_drv_ohm_p		= 40,
	.soc_data_drv_ohm_n		= 40,
	.soc_data_odt_ohm_p		= 0,
	.soc_data_odt_ohm_n		= 120,
	.dram_data_drv_ohm		= 40, //lpddr4 sdram only240/1-6
	.dram_data_odt_ohm		= 120,
	.dram_ac_odt_ohm		= 120,
	.soc_clk_slew_rate		= 0x3ff,//0x253,
	.soc_cs_slew_rate		= 0x100,//0x253,
	.soc_ac_slew_rate		= 0x100,//0x253,
	.soc_data_slew_rate		= 0x1ff,
	.vref_output_permil		= 350,//200,
	.vref_receiver_permil	= 200,
	.vref_dram_permil		= 350,
	//.vref_reverse			= 0,
	.ac_trace_delay			= {00,0x0,0,0,0,0,0x0,00},
	.ac_pinmux				= {00,00},
	.ddr_dmc_remap			= {
							[0] = ( 5 |  6 << 5 |  7 << 10 |  8<< 15 | 9<< 20 | 10 << 25 ),
							[1] = ( 11|  0 << 5 |  0 << 10 | 15 << 15 | 16 << 20 | 17 << 25 ),
							[2] = ( 18| 19 << 5 | 20 << 10 | 21 << 15 | 22 << 20 | 23 << 25 ),
							[3] = ( 24| 25 << 5 | 26 << 10 | 27 << 15 | 28 << 20 | 29 << 25 ),
							[4] = ( 30| 12 << 5 | 13 << 10 |  14<< 15 |  0 << 20 |  0 << 25 ),
	},
	.ddr_lpddr34_ca_remap	= {00,00},
	.ddr_lpddr34_dq_remap	= {00,00},
	.dram_rtt_nom_wr_park	= {00,00},
	.pll_ssc_mode			= (1<<20) | (1<<8) | (2<<4) | 0,//center_ssc_1000ppm
	.ddr_func				= DDR_FUNC,
	.magic					= DRAM_CFG_MAGIC,
},
{
	// lpddr3
	.board_id				= CONFIG_BOARD_ID_MASK,
	.version				= 1,
	//.dram_rank_config		= CONFIG_DDR0_32BIT_RANK01_CH0,
	.dram_rank_config		= CONFIG_DDR0_32BIT_RANK01_CH0,
	.ddr_rfc_type			= DDR_RFC_TYPE_LPDDR4_4Gbx1,
	.DramType				= CONFIG_DDR_TYPE_LPDDR3,
	.DRAMFreq				= {600, 0, 0, 0},
	.ddr_base_addr			= CFG_DDR_BASE_ADDR,
	.ddr_start_offset		= CFG_DDR_START_OFFSET,
	.DisabledDbyte			= 0xf0,
	.Is2Ttiming				= 0,
	.HdtCtrl				= 0xa,//0xa,
	.dram_cs0_size_MB		= 0xffff,//1024,
	.dram_cs1_size_MB		= 0xffff,//1024,
	.training_SequenceCtrl	= {0x131f,0}, //ddr3 0x21f 0x31f
	.phy_odt_config_rank	= {0x23,0x13}, //use 0x23 0x13  compatibility with 1rank and 2rank //targeting rank 0. [3:0] is used //for write ODT [7:4] is used for //read ODT
	.dfi_odt_config			= 0x0d0d,  //use 0d0d compatibility with 1rank and 2rank  //0808
	.PllBypassEn			= 0, //bit0-ps0,bit1-ps1
	.ddr_rdbi_wr_enable		= 0,
	.pll_ssc_mode			= (1<<20) | (1<<8) | (2<<4) | 0,//center_ssc_1000ppm
	.clk_drv_ohm			= 40,
	.cs_drv_ohm				= 40,
	.ac_drv_ohm				= 40,
	.soc_data_drv_ohm_p		= 40,
	.soc_data_drv_ohm_n		= 40,
	.soc_data_odt_ohm_p		= 60,
	.soc_data_odt_ohm_n		= 0,
	.dram_data_drv_ohm		= 30, //
	.dram_data_odt_ohm		= 120,
	.dram_ac_odt_ohm		= 0,
	.soc_clk_slew_rate		= 0x3ff,//0x253,
	.soc_cs_slew_rate		= 0x3ff,//0x253,
	.soc_ac_slew_rate		= 0x3ff,//0x253,
	.soc_data_slew_rate		= 0x2ff,
	.vref_output_permil		= 800,//200,
	.vref_receiver_permil	= 700,//875,  //700 for drv 40 odt 60 is better ,why?
	.vref_dram_permil		= 500,//875,
	//.vref_reverse			= 0,
	.ac_trace_delay			= {0x10,0x0,0x10-6,0x10-6,0x10-6,0x0,0x0,0x0,0x0,0x0},
	.ac_pinmux				= {00,00},
	.ddr_dmc_remap			= {
							[0] = ( 5 |  6 << 5 |  7 << 10 |  8<< 15 | 9<< 20 | 10 << 25 ),
							[1] = ( 11|  29 << 5 |  0 << 10 | 15 << 15 | 16 << 20 | 17 << 25 ),
							[2] = ( 18| 19 << 5 | 20 << 10 | 21 << 15 | 22 << 20 | 23 << 25 ),
							[3] = ( 24| 25 << 5 | 26 << 10 | 27 << 15 | 28 << 20 | 30 << 25 ),
							[4] = ( 31| 12 << 5 | 13 << 10 |  14<< 15 |  0 << 20 |  0 << 25 ),
	},
	.ddr_lpddr34_ca_remap	= {21/8,8/8,31/8,1/8},// {2,7,1,4,5,6,0,3,9,8},
	.ddr_lpddr34_dq_remap	= {1,2,7,4,0,3,5,6,8,12,14,9,11,10,15,13,21,22,16,17,23,20,19,18,31,29,26,27,30,28,25,24},
	//{21,22,16,17,23,20,19,18,8,12,14,9,11,10,15,13,31,29,26,27,30,28,25,24,1,2,7,4,0,3,5,6},
	.dram_rtt_nom_wr_park	= {00,00},
	.ddr_func				= DDR_FUNC,
	.magic					= DRAM_CFG_MAGIC,
	.diagnose				= CONFIG_DIAGNOSE_DISABLE,
},
*/
};

pll_set_t __pll_setting = {
	.cpu_clk				= CONFIG_CPU_CLK / 24 * 24,
#ifdef CONFIG_PXP_EMULATOR
	.pxp					= 1,
#else
	.pxp					= 0,
#endif
	.spi_ctrl				= 0,
	.lCustomerID			= CONFIG_AML_CUSTOMER_ID,
#ifdef CONFIG_DEBUG_MODE
	.debug_mode				= CONFIG_DEBUG_MODE,
	.ddr_clk_debug			= CONFIG_DDR_CLK_DEBUG,
	.cpu_clk_debug			= CONFIG_CPU_CLK_DEBUG,
#endif

#ifdef CONFIG_AML_SUPPORT_TLV
	.nCFGTAddr              = AML_BL2_TMASTER_DDR_ADDR,
#endif

};

ddr_reg_t __ddr_reg[] = {
	/* demo, user defined override register */
	{0xaabbccdd, 0, 0, 0, 0, 0},
	{0x11223344, 0, 0, 0, 0, 0},
	{0, 0, 0, 0, 0, 0},
};

#define VCCK_VAL				CONFIG_VCCK_INIT_VOLTAGE
#define VDDEE_VAL				CONFIG_VDDEE_INIT_VOLTAGE
/* VCCK PWM table */
#if   (VCCK_VAL == 800)
	#define VCCK_VAL_REG	0x0018000A
#elif (VCCK_VAL == 810)
	#define VCCK_VAL_REG	0x0017000B
#elif (VCCK_VAL == 820)
	#define VCCK_VAL_REG	0x0016000C
#elif (VCCK_VAL == 830)
	#define VCCK_VAL_REG	0x0015000D
#elif (VCCK_VAL == 840)
	#define VCCK_VAL_REG	0x0014000E
#elif (VCCK_VAL == 850)
	#define VCCK_VAL_REG	0x0013000F
#elif (VCCK_VAL == 860)
	#define VCCK_VAL_REG	0x00120010
#elif (VCCK_VAL == 870)
	#define VCCK_VAL_REG	0x00110011
#elif (VCCK_VAL == 880)
	#define VCCK_VAL_REG	0x00100012
#elif (VCCK_VAL == 890)
	#define VCCK_VAL_REG	0x000F0013
#elif (VCCK_VAL == 900)
	#define VCCK_VAL_REG	0x000E0014
#elif (VCCK_VAL == 910)
	#define VCCK_VAL_REG	0x000D0015
#elif (VCCK_VAL == 920)
	#define VCCK_VAL_REG	0x000C0016
#elif (VCCK_VAL == 930)
	#define VCCK_VAL_REG	0x000B0017
#elif (VCCK_VAL == 940)
	#define VCCK_VAL_REG	0x000A0018
#elif (VCCK_VAL == 950)
	#define VCCK_VAL_REG	0x00090019
#elif (VCCK_VAL == 960)
	#define VCCK_VAL_REG	0x0008001A
#elif (VCCK_VAL == 970)
	#define VCCK_VAL_REG	0x0007001B
#elif (VCCK_VAL == 980)
	#define VCCK_VAL_REG	0x0006001C
#elif (VCCK_VAL == 990)
	#define VCCK_VAL_REG	0x0005001D
#elif (VCCK_VAL == 1000)
	#define VCCK_VAL_REG	0x0004001E
#elif (VCCK_VAL == 1010)
	#define VCCK_VAL_REG	0x0003001F
#else
	#error "VCCK val out of range\n"
#endif

/* VDDEE PWM table */
#if    (VDDEE_VAL == 740)
	#define VDDEE_VAL_REG	0x00120000
#elif (VDDEE_VAL == 750)
	#define VDDEE_VAL_REG	0x00110001
#elif (VDDEE_VAL == 760)
	#define VDDEE_VAL_REG	0x00100002
#elif (VDDEE_VAL == 770)
	#define VDDEE_VAL_REG	0x000f0003
#elif (VDDEE_VAL == 780)
	#define VDDEE_VAL_REG	0x000e0004
#elif (VDDEE_VAL == 790)
	#define VDDEE_VAL_REG	0x000d0005
#elif (VDDEE_VAL == 800)
	#define VDDEE_VAL_REG	0x000c0006
#elif (VDDEE_VAL == 810)
	#define VDDEE_VAL_REG	0x000b0007
#elif (VDDEE_VAL == 820)
	#define VDDEE_VAL_REG	0x000a0008
#elif (VDDEE_VAL == 830)
	#define VDDEE_VAL_REG	0x00090009
#elif (VDDEE_VAL == 840)
	#define VDDEE_VAL_REG	0x0008000a
#elif (VDDEE_VAL == 850)
	#define VDDEE_VAL_REG	0x0007000b
#elif (VDDEE_VAL == 860)
	#define VDDEE_VAL_REG	0x0006000c
#elif (VDDEE_VAL == 870)
	#define VDDEE_VAL_REG	0x0005000d
#elif (VDDEE_VAL == 880)
	#define VDDEE_VAL_REG	0x0004000e
#elif (VDDEE_VAL == 890)
	#define VDDEE_VAL_REG	0x0003000f
#elif (VDDEE_VAL == 900)
	#define VDDEE_VAL_REG	0x00020010
#elif (VDDEE_VAL == 910)
	#define VDDEE_VAL_REG	0x00010011
#elif (VDDEE_VAL == 920)
	#define VDDEE_VAL_REG	0x00000012
#else
	#error "VDDEE val out of range\n"
#endif

/* for PWM use */
/* PWM driver check http://scgit.amlogic.com:8080/#/c/38093/ */
#define GPIO_O_EN_N_REG3	((0xff634400 + (0x19 << 2)))
#define GPIO_O_REG3		((0xff634400 + (0x1a << 2)))
#define GPIO_I_REG3		((0xff634400 + (0x1b << 2)))
#define AO_PIN_MUX_REG0	((0xff800000 + (0x05 << 2)))
#define AO_PIN_MUX_REG1	((0xff800000 + (0x06 << 2)))

bl2_reg_t __bl2_reg[] = {
	/* demo, user defined override register */
	/* eg: PWM init */

	/* PWM_AO_D */
	/* VCCK_VAL_REG: check PWM table */
	{AO_PWM_PWM_D,        VCCK_VAL_REG,            0xffffffff,   0, BL2_INIT_STAGE_1, 0},
	{AO_PWM_MISC_REG_CD,  ((1 << 23) | (1 << 1)),  (0x7f << 16), 0, BL2_INIT_STAGE_1, 0},
	{AO_PIN_MUX_REG1,     (3 << 20),               (0xF << 20),  0, BL2_INIT_STAGE_1, 0},
	/* PWM_AO_B */
	/* VDDEE_VAL_REG: check PWM table */
	{AO_PWM_PWM_B,        VDDEE_VAL_REG,           0xffffffff,   0, BL2_INIT_STAGE_1, 0},
	{AO_PWM_MISC_REG_AB,  ((1 << 23) | (1 << 1)),  (0x7f << 16), 0, BL2_INIT_STAGE_1, 0},
	{AO_PIN_MUX_REG1,     (3 << 16),               (0xF << 16),  0, BL2_INIT_STAGE_1, 0},
	/* Enable 5V_EN ,set gpioao_3 low --> several millisecond--set high in board_init*/
	{AO_GPIO_O_EN_N,    (0 << 3),                (1 << 3),     0, BL2_INIT_STAGE_1, 0},
	{AO_GPIO_O,         (0 << 3),                (1 << 3),   0, BL2_INIT_STAGE_1, 0},
	/* Enable VCCK GPIOAO_2*/
	{AO_GPIO_O_EN_N,      (0 << 2),                (1 << 2),  	 0, BL2_INIT_STAGE_1, 0},
	{AO_GPIO_O,           (1 << 2),                (1 << 2),  	 0, BL2_INIT_STAGE_1, 0},
};