
/*
 * board/amlogic/configs/gxb_p200_v1.h
 *
 * Copyright (C) 2015 Amlogic, Inc. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
 * more details.
 *
 * You should have received a copy of the GNU General Public License along
 * with this program; if not, write to the Free Software Foundation, Inc.,
 * 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
*/

#ifndef __GXB_P200_V1_H__
#define __GXB_P200_V1_H__

#ifndef __SUSPEND_FIRMWARE__
#include <asm/arch/cpu.h>
#endif		/* for compile problem of A53 and m3 */

#define CONFIG_SYS_GENERIC_BOARD  1
#ifndef __SUSPEND_FIRMWARE__
#ifndef CONFIG_AML_MESON
#warning "include warning"
#endif
#endif		/* for compile problem of A53 and m3 */

/*
 * platform power init config
 */
#define CONFIG_PLATFORM_POWER_INIT
#define CONFIG_VCCK_INIT_VOLTAGE	1100
#define CONFIG_VDDEE_INIT_VOLTAGE	1000		// voltage for power up
#define CONFIG_VDDEE_SLEEP_VOLTAGE	 850		// voltage for suspend

/* configs for CEC */
#define CONFIG_CEC_OSD_NAME		"Mbox"
#define CONFIG_CEC_WAKEUP

/* bt wake up */
#define CONFIG_BT_WAKEUP
/* wifi wake up */
#define CONFIG_WIFI_WAKEUP

#define CONFIG_INSTABOOT

/* support ext4*/
#define CONFIG_CMD_EXT4 1

/* Bootloader Control Block function
   That is used for recovery and the bootloader to talk to each other
  */
#define CONFIG_BOOTLOADER_CONTROL_BLOCK

/* SMP Definitinos */
#define CPU_RELEASE_ADDR		secondary_boot_func

/*a/b update */
#define CONFIG_CMD_BOOTCTOL_AVB

/* Serial config */
#define CONFIG_CONS_INDEX 2
#define CONFIG_BAUDRATE  115200
#define CONFIG_AML_MESON_SERIAL   1
#define CONFIG_SERIAL_MULTI		1
//for detect remote key
#define CONFIG_IR_REMOTE  1
//Enable ir remote wake up for bl30
#define CONFIG_IR_REMOTE_POWER_UP_KEY_CNT 4
#define CONFIG_IR_REMOTE_USE_PROTOCOL 0         // 0:nec  1:duokan  2:Toshiba 3:rca 4:rcmm
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL1 0XE51AFB04 //amlogic tv ir --- power
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL2 0XBB44FB04 //amlogic tv ir --- ch+
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL3 0xF20DFE01 //amlogic tv ir --- ch-
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL4 0xBA45BD02

#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL5 0x3ac5bd02
/* args/envs */
#define CONFIG_SYS_MAXARGS  64
#define CONFIG_EXTRA_ENV_SETTINGS \
        "firstboot=0\0"\
        "upgrade_step=0\0"\
        "jtag=disable\0"\
        "loadaddr=1080000\0"\
        "outputmode=1080p60hz\0" \
        "hdmimode=1080p60hz\0" \
        "cvbsmode=576cvbs\0" \
        "display_width=1920\0" \
        "display_height=1080\0" \
        "display_bpp=16\0" \
        "display_color_index=16\0" \
        "display_layer=osd1\0" \
        "display_color_fg=0xffff\0" \
        "display_color_bg=0\0" \
        "dtb_mem_addr=0x1000000\0" \
        "fb_addr=0x3d800000\0" \
        "fb_width=1920\0" \
        "fb_height=1080\0" \
        "frac_rate_policy=1\0" \
        "usb_burning=update 1000\0" \
        "fdt_high=0x20000000\0"\
        "try_auto_burn=update 700 750;\0"\
        "sdcburncfg=aml_sdc_burn.ini\0"\
        "sdc_burning=sdc_burn ${sdcburncfg}\0"\
        "wipe_data=successful\0"\
        "wipe_cache=successful\0"\
        "EnableSelinux=enforcing\0"\
        "recovery_part=recovery\0"\
        "recovery_offset=0\0"\
        "lock=10001000\0"\
        "cvbs_drv=0\0"\
        "active_slot=normal\0"\
        "boot_part=boot\0"\
        "reboot_mode_android=""normal""\0"\
        "fs_type=""rootfstype=ramfs""\0"\
        "initargs="\
            "init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 "\
            "\0"\
        "upgrade_check="\
            "echo upgrade_step=${upgrade_step}; "\
            "if itest ${upgrade_step} == 3; then "\
                "run init_display; run storeargs; run update;"\
            "else fi;"\
            "\0"\
        "storeargs="\
            "get_bootloaderversion;" \
            "setenv bootargs ${initargs} reboot_mode_android=${reboot_mode_android} androidboot.selinux=${EnableSelinux} logo=${display_layer},loaded,${fb_addr},${outputmode} vout=${outputmode},enable hdmimode=${hdmimode} cvbsmode=${cvbsmode} hdmitx=${cecconfig} cvbsdrv=${cvbs_drv} androidboot.firstboot=${firstboot} jtag=${jtag}; "\
	"setenv bootargs ${bootargs} androidboot.hardware=amlogic androidboot.bootloader=${bootloader_version} androidboot.build.expect.baseband=N/A;"\
            "run cmdline_keys;"\
            "\0"\
        "switch_bootmode="\
            "get_rebootmode;"\
            "if test ${reboot_mode} = factory_reset; then "\
                    "setenv reboot_mode_android ""normal"";"\
                    "run storeargs;"\
                    "run recovery_from_flash;"\
            "else if test ${reboot_mode} = update; then "\
                    "setenv reboot_mode_android ""normal"";"\
                    "run storeargs;"\
                    "run update;"\
            "else if test ${reboot_mode} = quiescent; then "\
                    "setenv reboot_mode_android ""quiescent"";"\
                    "run storeargs;"\
                    "setenv bootargs ${bootargs} androidboot.quiescent=1;"\
            "else if test ${reboot_mode} = recovery_quiescent; then "\
                    "setenv reboot_mode_android ""quiescent"";"\
                    "run storeargs;"\
                    "setenv bootargs ${bootargs} androidboot.quiescent=1;"\
                    "run recovery_from_flash;"\
            "else if test ${reboot_mode} = cold_boot; then "\
                    "setenv reboot_mode_android ""normal"";"\
                    "run storeargs;"\
            "else if test ${reboot_mode} = fastboot; then "\
                "setenv reboot_mode_android ""normal"";"\
                "run storeargs;"\
                "fastboot;"\
            "fi;fi;fi;fi;fi;fi;"\
            "\0" \
        "storeboot="\
            "get_system_as_root_mode;"\
            "echo system_mode: ${system_mode};"\
            "if test ${system_mode} = 1; then "\
                    "setenv bootargs ${bootargs} ro rootwait skip_initramfs;"\
            "else "\
                    "setenv bootargs ${bootargs} ${fs_type};"\
            "fi;"\
            "get_valid_slot;"\
            "get_avb_mode;"\
            "echo active_slot: ${active_slot};"\
            "if test ${active_slot} != normal; then "\
                    "setenv bootargs ${bootargs} androidboot.slot_suffix=${active_slot};"\
            "fi;"\
            "if test ${avb2} = 0; then "\
                "if test ${active_slot} = _a; then "\
                    "setenv bootargs ${bootargs} root=/dev/mmcblk0p23;"\
                "else if test ${active_slot} = _b; then "\
                    "setenv bootargs ${bootargs} root=/dev/mmcblk0p24;"\
                "fi;fi;"\
            "fi;"\
            "if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;"\
            "run storeargs; run update;"\
            "\0"\
        "factory_reset_poweroff_protect="\
            "echo wipe_data=${wipe_data}; echo wipe_cache=${wipe_cache};"\
            "if test ${wipe_data} = failed; then "\
                "run init_display; run storeargs;"\
                "if mmcinfo; then "\
                    "run recovery_from_sdcard;"\
                "fi;"\
                "if usb start 0; then "\
                    "run recovery_from_udisk;"\
                "fi;"\
                "run recovery_from_flash;"\
            "fi; "\
            "if test ${wipe_cache} = failed; then "\
                "run init_display; run storeargs;"\
                "if mmcinfo; then "\
                    "run recovery_from_sdcard;"\
                "fi;"\
                "if usb start 0; then "\
                    "run recovery_from_udisk;"\
                "fi;"\
                "run recovery_from_flash;"\
            "fi; \0" \
         "update="\
            /*first usb burning, second sdc_burn, third ext-sd autoscr/recovery, last udisk autoscr/recovery*/\
            "run usb_burning; "\
            "run sdc_burning; "\
            "if mmcinfo; then "\
                "run recovery_from_sdcard;"\
            "fi;"\
            "if usb start 0; then "\
                "run recovery_from_udisk;"\
            "fi;"\
            "run recovery_from_flash;"\
            "\0"\
        "recovery_from_sdcard="\
            "setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};"\
            "if fatload mmc 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;"\
            "if fatload mmc 0 ${loadaddr} recovery.img; then "\
                    "if fatload mmc 0 ${dtb_mem_addr} dtb.img; then echo sd dtb.img loaded; fi;"\
                    "wipeisb; "\
                    "setenv bootargs ${bootargs} ${fs_type};"\
                    "bootm ${loadaddr};fi;"\
            "\0"\
        "recovery_from_udisk="\
            "setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};"\
            "if fatload usb 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;"\
            "if fatload usb 0 ${loadaddr} recovery.img; then "\
                "if fatload usb 0 ${dtb_mem_addr} dtb.img; then echo udisk dtb.img loaded; fi;"\
                "wipeisb; "\
                "setenv bootargs ${bootargs} ${fs_type};"\
                "bootm ${loadaddr};fi;"\
            "\0"\
        "recovery_from_flash="\
            "get_valid_slot;"\
            "echo active_slot: ${active_slot};"\
            "if test ${active_slot} = normal; then "\
                "setenv bootargs ${bootargs} ${fs_type} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};"\
                "if itest ${upgrade_step} == 3; then "\
                    "if ext4load mmc 1:2 ${dtb_mem_addr} /recovery/dtb.img; then echo cache dtb.img loaded; fi;"\
                    "if ext4load mmc 1:2 ${loadaddr} /recovery/recovery.img; then echo cache recovery.img loaded; wipeisb; bootm ${loadaddr}; fi;"\
                "else fi;"\
                "if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then wipeisb; bootm ${loadaddr}; fi;"\
            "else "\
                "setenv bootargs ${bootargs} ${fs_type} aml_dt=${aml_dt} recovery_part=${boot_part} recovery_offset=${recovery_offset};"\
                "if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;"\
            "fi;"\
            "\0"\
        "init_display="\
            "get_rebootmode;"\
            "echo reboot_mode:::: ${reboot_mode};"\
            "if test ${reboot_mode} = quiescent; then "\
                    "setenv reboot_mode_android ""quiescent"";"\
                    "run storeargs;"\
                    "setenv bootargs ${bootargs} androidboot.quiescent=1;"\
                    "osd open;osd clear;"\
            "else if test ${reboot_mode} = recovery_quiescent; then "\
                    "setenv reboot_mode_android ""quiescent"";"\
                    "run storeargs;"\
                    "setenv bootargs ${bootargs} androidboot.quiescent=1;"\
                    "osd open;osd clear;"\
            "else "\
                "setenv reboot_mode_android ""normal"";"\
                "run storeargs;"\
                "osd open;osd clear;imgread pic logo bootup $loadaddr;bmp display $bootup_offset;bmp scale; "\
            "fi;fi;"\
            "\0"\
        "cmdline_keys="\
            "if keyman init 0x1234; then "\
                "if keyman read usid ${loadaddr} str; then "\
                    "setenv bootargs ${bootargs} androidboot.serialno=${usid};"\
                    "setenv serial ${usid};"\
                "else "\
                    "setenv bootargs ${bootargs} androidboot.serialno=1234567890;"\
                    "setenv serial 1234567890;"\
                "fi;"\
                "if keyman read mac ${loadaddr} str; then "\
                    "setenv bootargs ${bootargs} mac=${mac} androidboot.mac=${mac};"\
                "fi;"\
                "if keyman read deviceid ${loadaddr} str; then "\
                    "setenv bootargs ${bootargs} androidboot.deviceid=${deviceid};"\
                "fi;"\
            "fi;"\
            "\0"\
        "bcb_cmd="\
            "get_avb_mode;"\
            "get_valid_slot;"\
            "\0"\
        "upgrade_key="\
            "if gpio input GPIOAO_3; then "\
                "echo detect upgrade key; run update;"\
            "fi;"\
            "\0"\
	"irremote_update="\
		"if irkey 2500000 0xe31cfb04 0xb748fb04; then "\
			"echo read irkey ok!; " \
		"if itest ${irkey_value} == 0xe31cfb04; then " \
			"run update;" \
		"else if itest ${irkey_value} == 0xb748fb04; then " \
			"run update;\n" \
			"fi;fi;" \
		"fi;\0" \


#define CONFIG_PREBOOT  \
            "run bcb_cmd; "\
            "run factory_reset_poweroff_protect;"\
            "run upgrade_check;"\
            "run init_display;"\
            "run storeargs;"\
            "run upgrade_key;" \
            "bcb uboot-command;"\
            "run switch_bootmode;"
#define CONFIG_BOOTCOMMAND "run storeboot"

//#define CONFIG_ENV_IS_NOWHERE  1
#define CONFIG_ENV_SIZE   (64*1024)
#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
#define CONFIG_ANDROID_BOOT_IMAGE 1
#define CONFIG_ANDROID_IMG 1
#define CONFIG_SYS_BOOTM_LEN (64<<20) /* Increase max gunzip size*/

/* cpu */
#define CONFIG_CPU_CLK					1536 //MHz. Range: 600-1800, should be multiple of 24

/* ddr */
#define CONFIG_DDR_SIZE					1024 //MB
#define CONFIG_DDR_CLK					912  //MHz, Range: 384-1200, should be multiple of 24
#define CONFIG_DDR_TYPE					CONFIG_DDR_TYPE_DDR3
/* DDR channel setting, please refer hardware design.
 *    CONFIG_DDR0_RANK0_ONLY   : one channel
 *    CONFIG_DDR0_RANK01_SAME  : one channel use two rank with same setting
 *    CONFIG_DDR0_RANK01_DIFF  : one channel use two rank with diff setting
 *    CONFIG_DDR01_SHARE_AC    : two channels  */
#define CONFIG_DDR_CHANNEL_SET			CONFIG_DDR0_RANK01_SAME
#define CONFIG_DDR_FULL_TEST			0 //1 for ddr full test
#define CONFIG_NR_DRAM_BANKS			1
/* ddr power saving */
#define CONFIG_DDR_ZQ_POWER_DOWN
#define CONFIG_DDR_POWER_DOWN_PHY_VREF
/* ddr detection */
#define CONFIG_DDR_SIZE_AUTO_DETECT     1 //0:disable, 1:enable
/* ddr functions */
#define CONFIG_CMD_DDR_D2PLL            0 //0:disable, 1:enable. d2pll cmd
#define CONFIG_CMD_DDR_TEST             0 //0:disable, 1:enable. ddrtest cmd

/* storage: emmc/nand/sd */
#define	CONFIG_STORE_COMPATIBLE 1
#define CONFIG_AML_NAND	1
/* env */
#define 	CONFIG_ENV_OVERWRITE
#define 	CONFIG_CMD_SAVEENV
/* fixme, need fix*/

#if (defined(CONFIG_ENV_IS_IN_AMLNAND) || defined(CONFIG_ENV_IS_IN_MMC)) && defined(CONFIG_STORE_COMPATIBLE)
#error env in amlnand/mmc already be compatible;
#endif

#define CONFIG_AML_SD_EMMC 1
#ifdef	CONFIG_AML_SD_EMMC
	#define CONFIG_GENERIC_MMC 1
	#define CONFIG_CMD_MMC 1
    #define CONFIG_CMD_GPT 1
	#define	CONFIG_SYS_MMC_ENV_DEV 1
	#define CONFIG_EMMC_DDR52_EN 0
	#define CONFIG_EMMC_DDR52_CLK 52000000
#endif

#define	CONFIG_PARTITIONS 1
#define CONFIG_SYS_NO_FLASH  1
//#define     CONFIG_AML_GPT

/* vpu */
#define CONFIG_AML_VPU 1
#define CONFIG_VPU_CLK_LEVEL_DFT 7

/* DISPLAY & HDMITX */
#define CONFIG_AML_HDMITX20 1
#define CONFIG_AML_CANVAS 1
#define CONFIG_AML_VOUT 1
#define CONFIG_AML_OSD 1
#define CONFIG_AML_MINUI 1
#define CONFIG_OSD_SCALE_ENABLE 1
#define CONFIG_CMD_BMP 1

#if defined(CONFIG_AML_VOUT)
#define CONFIG_AML_CVBS 1
#endif

/* USB
 * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard
 * Enable CONFIG_MUSB_UDD for Device functionalities.
 */
/* #define CONFIG_MUSB_UDC		1 */
#define CONFIG_CMD_USB 1
#if defined(CONFIG_CMD_USB)
	#define CONFIG_M8_USBPORT_BASE_A	0xC9000000
	#define CONFIG_M8_USBPORT_BASE_B	0xC9100000
	#define CONFIG_USB_STORAGE      1
	#define CONFIG_USB_DWC_OTG_HCD  1
	#define CONFIG_USB_DWC_OTG_294	1
#endif //#if defined(CONFIG_CMD_USB)

//UBOOT fastboot config
#define CONFIG_CMD_FASTBOOT 1
#define CONFIG_FASTBOOT_FLASH_MMC_DEV 1
#define CONFIG_FASTBOOT_FLASH 1
#define CONFIG_USB_GADGET 1
#define CONFIG_USBDOWNLOAD_GADGET 1
#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_FASTBOOT_MAX_DOWN_SIZE	0x8000000
#define CONFIG_DEVICE_PRODUCT	"p200"

//UBOOT Facotry usb/sdcard burning config
#define CONFIG_AML_V2_FACTORY_BURN              1
#define CONFIG_AML_FACTORY_BURN_LOCAL_UPGRADE   1       //support factory sdcard burning
#define CONFIG_POWER_KEY_NOT_SUPPORTED_FOR_BURN 1       //There isn't power-key for factory sdcard burning
#define CONFIG_SD_BURNING_SUPPORT_UI            1       //Displaying upgrading progress bar when sdcard/udisk burning

#define CONFIG_AML_SECURITY_KEY                 1
#define CONFIG_UNIFY_KEY_MANAGE                 1

/* net */
#define CONFIG_CMD_NET   1
#if defined(CONFIG_CMD_NET)
	#define CONFIG_DESIGNWARE_ETH 1
	#define CONFIG_PHYLIB	1
	#define CONFIG_NET_MULTI 1
	#define CONFIG_CMD_PING 1
	#define CONFIG_CMD_DHCP 1
	#define CONFIG_CMD_RARP 1
	#define CONFIG_HOSTNAME        arm_gxbb
	#define CONFIG_RANDOM_ETHADDR  1				   /* use random eth addr, or default */
	#define CONFIG_ETHADDR         00:15:18:01:81:31   /* Ethernet address */
	#define CONFIG_IPADDR          10.18.9.97          /* Our ip address */
	#define CONFIG_GATEWAYIP       10.18.9.1           /* Our getway ip address */
	#define CONFIG_SERVERIP        10.18.9.113         /* Tftp server ip address */
	#define CONFIG_NETMASK         255.255.255.0
#endif /* (CONFIG_CMD_NET) */

/* other devices */
#define CONFIG_EFUSE 1
#define CONFIG_SYS_I2C_AML 1
#define CONFIG_SYS_I2C_SPEED     400000

/* commands */
#define CONFIG_CMD_CACHE 1
#define CONFIG_CMD_BOOTI 1
#define CONFIG_CMD_EFUSE 1
#define CONFIG_CMD_I2C 1
#define CONFIG_CMD_MEMORY 1
#define CONFIG_CMD_FAT 1
#define CONFIG_CMD_GPIO 1
#define CONFIG_CMD_RUN
#define CONFIG_CMD_REBOOT 1
#define CONFIG_CMD_ECHO 1
#define CONFIG_CMD_JTAG	1
#define CONFIG_CMD_AUTOSCRIPT 1

/*file system*/
#define CONFIG_DOS_PARTITION 1
#define CONFIG_EFI_PARTITION 1
#define CONFIG_AML_PARTITION 1
#define CONFIG_MMC 1
#define CONFIG_FS_FAT 1
#define CONFIG_FS_EXT4 1
#define CONFIG_LZO 1

/* Cache Definitions */
//#define CONFIG_SYS_DCACHE_OFF
//#define CONFIG_SYS_ICACHE_OFF

/* other functions */
#define CONFIG_NEED_BL301	1
#define CONFIG_NEED_BL32	1
#define CONFIG_CMD_RSVMEM	1
#define CONFIG_FIP_IMG_SUPPORT	1
#define CONFIG_BOOTDELAY	1 //delay 1s
#define CONFIG_SYS_LONGHELP 1
#define CONFIG_CMD_MISC     1
#define CONFIG_CMD_ITEST    1
#define CONFIG_CMD_CPU_TEMP 1
#define CONFIG_SYS_MEM_TOP_HIDE 0x08000000 //hide 128MB for kernel reserve
#define CONFIG_MULTI_DTB    1

//support secure boot
#define CONFIG_AML_SECURE_UBOOT   1

#if defined(CONFIG_AML_SECURE_UBOOT)

//for GXBB SRAM size limitation just disable NAND
//as the socket board default has no NAND
//#undef CONFIG_AML_NAND

//unify build for generate encrypted bootloader "u-boot.bin.encrypt"
#define CONFIG_AML_CRYPTO_UBOOT   1

//unify build for generate encrypted kernel image
//SRC : "board/amlogic/gxb_skt_v1/boot.img"
//DST : "fip/boot.img.encrypt"
//#define CONFIG_AML_CRYPTO_IMG       1

#endif //CONFIG_AML_SECURE_UBOOT


#define CONFIG_SECURE_STORAGE 1

//build with uboot auto test
//#define CONFIG_AML_UBOOT_AUTO_TEST 1

//board customer ID
//#define CONFIG_CUSTOMER_ID  (0x6472616F624C4D41)

#if defined(CONFIG_CUSTOMER_ID)
  #undef CONFIG_AML_CUSTOMER_ID
  #define CONFIG_AML_CUSTOMER_ID  CONFIG_CUSTOMER_ID
#endif

#endif