
/*
 * board/amlogic/configs/gxtvbb_p310_v1.h
 *
 * Copyright (C) 2015 Amlogic, Inc. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
 * more details.
 *
 * You should have received a copy of the GNU General Public License along
 * with this program; if not, write to the Free Software Foundation, Inc.,
 * 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
*/

#ifndef __GXTVBB_P310_V1_H__
#define __GXTVBB_P310_V1_H__

#include <asm/arch/cpu.h>

#define CONFIG_SYS_GENERIC_BOARD  1
#ifndef CONFIG_AML_MESON
#warning "include warning"
#endif

/*
 * platform power init config
 */
#define CONFIG_PLATFORM_POWER_INIT
#define CONFIG_VCCK_INIT_VOLTAGE	1100
#define CONFIG_VDDEE_INIT_VOLTAGE	1100		// voltage for power up
#define CONFIG_VDDEE_SLEEP_VOLTAGE	 850		// voltage for suspend

/* configs for CEC */
#define CONFIG_CEC_OSD_NAME		"AML_TV"
#define CONFIG_CEC_WAKEUP

#define CONFIG_INSTABOOT

/* Bootloader Control Block function
   That is used for recovery and the bootloader to talk to each other
  */
#define CONFIG_BOOTLOADER_CONTROL_BLOCK

/* SMP Definitinos */
#define CPU_RELEASE_ADDR		secondary_boot_func

/* Serial config */
#define CONFIG_CONS_INDEX 2
#define CONFIG_BAUDRATE  115200
#define CONFIG_AML_MESON_SERIAL   1
#define CONFIG_SERIAL_MULTI		1
#define CONFIG_IR_REMOTE  1
//Enable ir remote wake up for bl30
#define CONFIG_IR_REMOTE_POWER_UP_KEY_CNT 8
#define CONFIG_IR_REMOTE_USE_PROTOCOL 0         // 0:nec  1:duokan  2:Toshiba 3:rca
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL1 0xef10fe01 //amlogic nec tv ir --- power
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL2 0xf30cfe01 //amlogic nec tv ir --- ch+
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL3 0xf20dfe01 //amlogic nec tv ir --- ch-
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL4 0xe51afb04 //amlogic nec box ir --- power
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL5 0xFFFFFFFF //amlogic nec tv ir --- right
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL6 0x00f2a0d5  //tcl rca
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL7 0xf40b1818  //hair toshiba
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL8 0xf30c0e0e  //skyworth
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL9 0xFFFFFFFF

/*config the default parameters for adc power key*/
#define CONFIG_ADC_POWER_KEY_CHAN   2  /*channel range: 0-7*/
#define CONFIG_ADC_POWER_KEY_VAL    0  /*sample value range: 0-1023*/

/* args/envs */
#define CONFIG_SYS_MAXARGS  64
#define CONFIG_EXTRA_ENV_SETTINGS \
	"firstboot=0\0"\
	"upgrade_step=0\0"\
	"loadaddr=1080000\0"\
	"dtb_mem_addr=0x1000000\0" \
	"outputmode=1080p60hz\0" \
	"panel_reverse=0\0" \
	"osd_reverse=n\0" \
	"video_reverse=n\0" \
	"display_width=1920\0" \
	"display_height=1080\0" \
	"display_bpp=16\0" \
	"display_color_index=16\0" \
	"display_layer=osd1\0" \
	"display_color_fg=0xffff\0" \
	"display_color_bg=0\0" \
	"fb_addr=0x3b000000\0" \
	"fb_width=1920\0" \
	"fb_height=1080\0" \
	"usb_burning=update 1000\0" \
	"fdt_high=0x20000000\0"\
	"try_auto_burn=update 700 750;\0"\
	"sdcburncfg=aml_sdc_burn.ini\0"\
	"sdc_burning=sdc_burn ${sdcburncfg}\0"\
	"wipe_data=successful\0"\
	"wipe_cache=successful\0"\
	"lock=10001000\0"\
	"EnableSelinux=enforcing\0" \
	"jtag=apao\0"\
	"active_slot=_a\0"\
	"boot_part=boot\0"\
	"upgrade_check="\
		"echo upgrade_step=${upgrade_step}; "\
		"if itest ${upgrade_step} == 3; then "\
			"run init_display; run storeargs; run update; "\
		"else fi; "\
		"\0"\
	"storeargs="\
		"setenv bootargs rootfstype=ramfs init=/init "\
		"console=ttyS0,115200 no_console_suspend "\
		"earlyprintk=aml-uart,0xc81004c0 "\
		"androidboot.selinux=${EnableSelinux} "\
		"logo=${display_layer},loaded,${fb_addr} "\
		"vout=${outputmode},enable "\
		"osd_reverse=${osd_reverse} video_reverse=${video_reverse} "\
		"jtag=${jtag} "\
		"androidboot.firstboot=${firstboot}; "\
		"setenv bootargs ${bootargs} androidboot.hardware=amlogic;"\
		"run cmdline_keys; "\
		"setenv bootargs ${bootargs} androidboot.slot_suffix=${active_slot};"\
		"\0"\
	"switch_bootmode="\
		"get_rebootmode; "\
		"if test ${reboot_mode} = factory_reset; then "\
			"run recovery_from_flash; "\
		"else if test ${reboot_mode} = update; then "\
			"run update; "\
		"else if test ${reboot_mode} = cold_boot; then "\
			"run try_auto_burn; "\
		"else if test ${reboot_mode} = fastboot; then "\
			"fastboot;"\
		"fi;fi;fi;fi;"\
		"\0" \
	"storeboot="\
		"if imgread kernel ${boot_part} ${loadaddr}; then "\
			"bootm ${loadaddr}; "\
		"fi; "\
		"run update; "\
		"\0"\
	"factory_reset_poweroff_protect="\
		"echo wipe_data=${wipe_data}; echo wipe_cache=${wipe_cache}; "\
		"if test ${wipe_data} = failed; then "\
			"run init_display; run storeargs; "\
			"if mmcinfo; then "\
				"run recovery_from_sdcard; "\
			"fi; "\
			"if usb start 0; then "\
				"run recovery_from_udisk; "\
			"fi; "\
			"run recovery_from_flash; "\
		"fi; "\
		"if test ${wipe_cache} = failed; then "\
			"run init_display; run storeargs; "\
			"if mmcinfo; then "\
				"run recovery_from_sdcard; "\
			"fi; "\
			"if usb start 0; then "\
				"run recovery_from_udisk; "\
			"fi; "\
			"run recovery_from_flash; "\
		"fi; "\
		"\0" \
	"update="\
		"run usb_burning; "\
		"run sdc_burning; "\
		"if mmcinfo; then "\
			"run recovery_from_sdcard; "\
		"fi; "\
		"if usb start 0; then "\
			"run recovery_from_udisk; "\
		"fi; "\
		"run recovery_from_flash; "\
		"\0"\
	"recovery_from_sdcard="\
	      "setenv bootargs ${bootargs} aml_dt=${aml_dt};"\
		"if fatload mmc 0 ${loadaddr} aml_autoscript; then "\
			"autoscr ${loadaddr}; "\
		"fi; "\
		"if fatload mmc 0 ${loadaddr} recovery.img; then "\
			"if fatload mmc 0 ${dtb_mem_addr} dtb.img; then "\
				"echo sd dtb.img loaded; "\
			"fi; "\
			"wipeisb; "\
			"bootm ${loadaddr}; "\
		"fi; "\
		"\0"\
	"recovery_from_udisk="\
	      "setenv bootargs ${bootargs} aml_dt=${aml_dt};"\
		"if fatload usb 0 ${loadaddr} aml_autoscript; then "\
			"autoscr ${loadaddr}; "\
		"fi; "\
		"if fatload usb 0 ${loadaddr} recovery.img; then "\
			"if fatload usb 0 ${dtb_mem_addr} dtb.img; then "\
				"echo udisk dtb.img loaded; "\
			"fi; "\
			"wipeisb; "\
			"bootm ${loadaddr}; "\
		"fi; "\
		"\0"\
	"recovery_from_flash="\
                "setenv bootargs ${bootargs} aml_dt=${aml_dt};"\
		"if imgread kernel recovery ${loadaddr}; then "\
			"wipeisb; "\
			"bootm ${loadaddr}; "\
		"fi"\
		"\0"\
	"init_display="\
		"osd open; osd clear; "\
		"vout output ${outputmode}; "\
		"imgread pic logo bootup $loadaddr; "\
		"bmp display $bootup_offset; bmp scale"\
		"\0"\
	"bcb_cmd="\
		"get_valid_slot;"\
		"\0"\
	"cmdline_keys="\
		"if keyman init 0x1234; then "\
			"if keyman read usid ${loadaddr} str; then "\
				"setenv bootargs ${bootargs} "\
				"androidboot.serialno=${usid}; "\
				"setenv serial ${usid};"\
			"else "\
				"setenv bootargs ${bootargs} androidboot.serialno=1234567890;"\
				"setenv serial 1234567890;"\
			"fi; "\
			"if keyman read mac ${loadaddr} str; then "\
				"setenv bootargs ${bootargs} "\
				"mac=${mac} androidboot.mac=${mac}; "\
			"fi; "\
			"if keyman read deviceid ${loadaddr} str; then "\
				"setenv bootargs ${bootargs} "\
				"androidboot.deviceid=${deviceid}; "\
			"fi; "\
		"fi; "\
		"\0"\

#define CONFIG_PREBOOT  \
	"run bcb_cmd; "\
	"run factory_reset_poweroff_protect; "\
	"run upgrade_check; "\
	"run init_display; "\
	"run storeargs; "\
	"run switch_bootmode;"
#define CONFIG_BOOTCOMMAND "run storeboot"

//#define CONFIG_ENV_IS_NOWHERE  1
#define CONFIG_ENV_SIZE   (64*1024)
#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
#define CONFIG_ANDROID_BOOT_IMAGE 1
#define CONFIG_ANDROID_IMG 1
#define CONFIG_SYS_BOOTM_LEN (64<<20) /* Increase max gunzip size*/

/* cpu */
#define CONFIG_CPU_CLK					1536 //MHz. Range: 600-1800, should be multiple of 24

/* ddr */
#define CONFIG_DDR_SIZE					1024 //MB
#define CONFIG_DDR_CLK					720  //MHz, Range: 384-1200, should be multiple of 24
#define CONFIG_DDR_TYPE					CONFIG_DDR_TYPE_DDR3
/* DDR channel setting, please refer hardware design.
 *    CONFIG_DDR0_ONLY_32BIT           : one channel 32bit
 *    CONFIG_DDR0_ONLY_16BIT           : one channel 16bit
 *    CONFIG_DDR01_TWO_CHANNEL         : two channels 32bit
 *    CONFIG_DDR01_TWO_CHANNEL_16BIT   : two channels 16bit */
#define CONFIG_DDR_CHANNEL_SET			CONFIG_DDR01_TWO_CHANNEL
#define CONFIG_DDR_FULL_TEST			0 //1 for ddr full test
#define CONFIG_NR_DRAM_BANKS			1
/* ddr power saving */
#define CONFIG_DDR_ZQ_POWER_DOWN
#define CONFIG_DDR_POWER_DOWN_PHY_VREF
/* ddr detection */
#define CONFIG_DDR_SIZE_AUTO_DETECT		0 //0:disable, 1:enable

/* storage: emmc/nand/sd */
#define		CONFIG_STORE_COMPATIBLE 1
#define 	CONFIG_ENV_OVERWRITE
#define 	CONFIG_CMD_SAVEENV
#define		CONFIG_ENV_IS_IN_MMC 1
#define		CONFIG_SYS_MMC_ENV_DEV 1
#define		CONFIG_AML_SD_EMMC 1
#ifdef		CONFIG_AML_SD_EMMC
	#define 	CONFIG_GENERIC_MMC 1
	#define 	CONFIG_CMD_MMC 1
    #define CONFIG_CMD_GPT 1
	#define CONFIG_EMMC_DDR52_EN 0
	#define CONFIG_EMMC_DDR52_CLK 52000000
#endif
//#define 	CONFIG_AML_NAND	1
#ifdef CONFIG_AML_NAND
#endif
#define		CONFIG_PARTITIONS 1
#define 	CONFIG_SYS_NO_FLASH  1


/* vpu */
#define CONFIG_AML_VPU 1
#define CONFIG_VPU_CLK_LEVEL_DFT 7

/* DISPLAY & HDMITX */
#define CONFIG_AML_HDMITX20 1
#define CONFIG_AML_CANVAS 1
#define CONFIG_AML_VOUT 1
#define CONFIG_AML_OSD 1
#define CONFIG_OSD_SCALE_ENABLE 1
#define CONFIG_CMD_BMP 1

#if defined(CONFIG_AML_VOUT)
#define CONFIG_AML_CVBS 1
#endif

//#define CONFIG_AML_LCD    1
#define CONFIG_AML_LCD_TV 1
/* #define CONFIG_AML_LCD_TABLET 1 */

/* USB
 * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard
 * Enable CONFIG_MUSB_UDD for Device functionalities.
 */
/* #define CONFIG_MUSB_UDC		1 */
#define CONFIG_CMD_USB 1
#if defined(CONFIG_CMD_USB)
	#define CONFIG_GXTVBB_XHCI_BASE		0xc9000000
	#define CONFIG_GXTVBB_USB_PHY2_BASE	0xd0078000
	#define CONFIG_GXTVBB_USB_PHY3_BASE	0xd0078080
	#define CONFIG_USB_STORAGE      1
	#define CONFIG_USB_XHCI 1
	#define CONFIG_USB_XHCI_AMLOGIC 1
#endif //#if defined(CONFIG_CMD_USB)

//UBOOT fastboot config
#define CONFIG_CMD_FASTBOOT 1
#define CONFIG_FASTBOOT_FLASH_MMC_DEV 1
#define CONFIG_FASTBOOT_FLASH 1
#define CONFIG_USB_GADGET 1
#define CONFIG_USBDOWNLOAD_GADGET 1
#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_FASTBOOT_MAX_DOWN_SIZE	0x8000000
#define CONFIG_DEVICE_PRODUCT	"p310"

//UBOOT Facotry usb/sdcard burning config
#define CONFIG_AML_V2_FACTORY_BURN              1       //support facotry usb burning
#define CONFIG_AML_FACTORY_BURN_LOCAL_UPGRADE   1       //support factory sdcard burning
#define CONFIG_POWER_KEY_NOT_SUPPORTED_FOR_BURN 1       //There isn't power-key for factory sdcard burning
#define CONFIG_SD_BURNING_SUPPORT_UI            1       //Displaying upgrading progress bar when sdcard/udisk burning

#define CONFIG_AML_SECURITY_KEY                 1
#define CONFIG_UNIFY_KEY_MANAGE                 1


/* net */
#define CONFIG_CMD_NET   1
#if defined(CONFIG_CMD_NET)
	#define CONFIG_DESIGNWARE_ETH 1
	#define CONFIG_PHYLIB	1
	#define CONFIG_NET_MULTI 1
	#define CONFIG_CMD_PING 1
	#define CONFIG_CMD_DHCP 1
	#define CONFIG_CMD_RARP 1
	#define CONFIG_HOSTNAME        arm_gxtvbb
	#define CONFIG_RANDOM_ETHADDR  1                   /* use random eth addr, or default */
	#define CONFIG_ETHADDR         00:15:18:01:81:31   /* Ethernet address */
	#define CONFIG_IPADDR          10.18.9.97          /* Our ip address */
	#define CONFIG_GATEWAYIP       10.18.9.1           /* Our getway ip address */
	#define CONFIG_SERVERIP        10.18.9.113         /* Tftp server ip address */
	#define CONFIG_NETMASK         255.255.255.0
#endif /* (CONFIG_CMD_NET) */

/* other devices */
#define CONFIG_EFUSE 1
#define CONFIG_SYS_I2C_AML 1
#define CONFIG_SYS_I2C_SPEED     400000

/* commands */
#define CONFIG_CMD_CACHE 1
#define CONFIG_CMD_BOOTI 1
#define CONFIG_CMD_EFUSE 1
#define CONFIG_CMD_I2C 1
#define CONFIG_CMD_MEMORY 1
#define CONFIG_CMD_FAT 1
#define CONFIG_CMD_GPIO 1
#define CONFIG_CMD_RUN
#define CONFIG_CMD_REBOOT 1
#define CONFIG_CMD_ECHO 1
#define CONFIG_CMD_JTAG	1
#define CONFIG_CMD_AUTOSCRIPT 1
#define CONFIG_CMD_MISC 1

/*file system*/
#define CONFIG_DOS_PARTITION 1
#define CONFIG_EFI_PARTITION 1
#define CONFIG_AML_PARTITION 1
#define CONFIG_MMC 1
#define CONFIG_FS_FAT 1
#define CONFIG_FS_EXT4 1
#define CONFIG_LZO 1

/* Cache Definitions */
//#define CONFIG_SYS_DCACHE_OFF
//#define CONFIG_SYS_ICACHE_OFF

/* other functions */
#define CONFIG_NEED_BL301	1
#define CONFIG_NEED_BL32	1
#define CONFIG_CMD_RSVMEM	1
#define CONFIG_FIP_IMG_SUPPORT	1
#define CONFIG_BOOTDELAY	1 //delay 1s
#define CONFIG_SYS_LONGHELP 1
#define CONFIG_CMD_MISC         1
#define CONFIG_CMD_ITEST    1
#define CONFIG_CMD_CPU_TEMP 1
#define CONFIG_SYS_MEM_TOP_HIDE 0x08000000 //hide 128MB for kernel reserve

#define CONFIG_MULTI_DTB    1

/* ddr dump function defines */
//#define CONFIG_SPL_DDR_DUMP 1
#ifdef CONFIG_SPL_DDR_DUMP
	#define CONFIG_SPL_DDR_DUMP_ADDR 			0x01000000
	#define CONFIG_SPL_DDR_DUMP_SIZE			0x00200000
	#define CONFIG_SPL_DDR_DUMP_DEV_TYPE		0x4 //device type, 1:emmc, 4:sd
	#define CONFIG_SPL_DDR_DUMP_DEV_OFFSET		0x40000000 //offset of store device
	#define CONFIG_SPL_DDR_DUMP_FLAG			0x1 //flag write in sticky reg
#endif

//support secure boot
#define CONFIG_AML_SECURE_UBOOT   1

#if defined(CONFIG_AML_SECURE_UBOOT)

//for GXBB SRAM size limitation just disable NAND
//as the socket board default has no NAND
#undef CONFIG_AML_NAND

//unify build for generate encrypted bootloader "u-boot.bin.encrypt"
#define CONFIG_AML_CRYPTO_UBOOT   1

//unify build for generate encrypted kernel image
//SRC : "board/amlogic/gxb_skt_v1/boot.img"
//DST : "fip/boot.img.encrypt"
//#define CONFIG_AML_CRYPTO_IMG       1

#endif //CONFIG_AML_SECURE_UBOOT

#define CONFIG_SECURE_STORAGE 1

#endif