blob: d1110dfd6e7b7b63c958d605832b6f59abc27c54 [file] [log] [blame] [edit]
/*
* (C) Copyright 2006
* Wolfgang Wegner, ASTRO Strobel Kommunikationssysteme GmbH,
* w.wegner@astro-kom.de
*
* based on the files by
* Heiko Schocher, DENX Software Engineering, hs@denx.de
* and
* Rich Ireland, Enterasys Networks, rireland@enterasys.com.
* Keith Outwater, keith_outwater@mvis.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/* Altera/Xilinx FPGA configuration support for the ASTRO "URMEL" board */
#include <common.h>
#include <watchdog.h>
#include <altera.h>
#include <ACEX1K.h>
#include <spartan3.h>
#include <command.h>
#include <asm/immap_5329.h>
#include <asm/io.h>
#include "fpga.h"
DECLARE_GLOBAL_DATA_PTR;
int altera_pre_fn(int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
unsigned char tmp_char;
unsigned short tmp_short;
/* first, set the required pins to GPIO function */
/* PAR_T0IN -> GPIO */
tmp_char = readb(&gpiop->par_timer);
tmp_char &= 0xfc;
writeb(tmp_char, &gpiop->par_timer);
/* all QSPI pins -> GPIO */
writew(0x0000, &gpiop->par_qspi);
/* U0RTS, U0CTS -> GPIO */
tmp_short = __raw_readw(&gpiop->par_uart);
tmp_short &= 0xfff3;
__raw_writew(tmp_short, &gpiop->par_uart);
/* all PWM pins -> GPIO */
writeb(0x00, &gpiop->par_pwm);
/* next, set data direction registers */
writeb(0x01, &gpiop->pddr_timer);
writeb(0x25, &gpiop->pddr_qspi);
writeb(0x0c, &gpiop->pddr_uart);
writeb(0x04, &gpiop->pddr_pwm);
/* ensure other SPI peripherals are deselected */
writeb(0x08, &gpiop->ppd_uart);
writeb(0x38, &gpiop->ppd_qspi);
/* CONFIG = 0 STATUS = 0 -> FPGA in reset state */
writeb(0xFB, &gpiop->pclrr_uart);
/* enable Altera configuration by clearing QSPI_CS2 and DT0IN */
writeb(0xFE, &gpiop->pclrr_timer);
writeb(0xDF, &gpiop->pclrr_qspi);
return FPGA_SUCCESS;
}
/* Set the state of CONFIG Pin */
int altera_config_fn(int assert_config, int flush, int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
if (assert_config)
writeb(0x04, &gpiop->ppd_uart);
else
writeb(0xFB, &gpiop->pclrr_uart);
return FPGA_SUCCESS;
}
/* Returns the state of STATUS Pin */
int altera_status_fn(int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
if (readb(&gpiop->ppd_pwm) & 0x08)
return FPGA_FAIL;
return FPGA_SUCCESS;
}
/* Returns the state of CONF_DONE Pin */
int altera_done_fn(int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
if (readb(&gpiop->ppd_pwm) & 0x20)
return FPGA_FAIL;
return FPGA_SUCCESS;
}
/*
* writes the complete buffer to the FPGA
* writing the complete buffer in one function is much faster,
* then calling it for every bit
*/
int altera_write_fn(const void *buf, size_t len, int flush, int cookie)
{
size_t bytecount = 0;
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
unsigned char *data = (unsigned char *)buf;
unsigned char val = 0;
int i;
int len_40 = len / 40;
while (bytecount < len) {
val = data[bytecount++];
i = 8;
do {
writeb(0xFB, &gpiop->pclrr_qspi);
if (val & 0x01)
writeb(0x01, &gpiop->ppd_qspi);
else
writeb(0xFE, &gpiop->pclrr_qspi);
writeb(0x04, &gpiop->ppd_qspi);
val >>= 1;
i--;
} while (i > 0);
if (bytecount % len_40 == 0) {
#if defined(CONFIG_HW_WATCHDOG) || defined(CONFIG_WATCHDOG)
WATCHDOG_RESET();
#endif
#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
putc('.'); /* let them know we are alive */
#endif
#ifdef CONFIG_SYS_FPGA_CHECK_CTRLC
if (ctrlc())
return FPGA_FAIL;
#endif
}
}
return FPGA_SUCCESS;
}
/* called, when programming is aborted */
int altera_abort_fn(int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
writeb(0x20, &gpiop->ppd_qspi);
writeb(0x08, &gpiop->ppd_uart);
return FPGA_SUCCESS;
}
/* called, when programming was succesful */
int altera_post_fn(int cookie)
{
return altera_abort_fn(cookie);
}
/*
* Note that these are pointers to code that is in Flash. They will be
* relocated at runtime.
* FIXME: relocation not yet working for coldfire, see below!
*/
Altera_CYC2_Passive_Serial_fns altera_fns = {
altera_pre_fn,
altera_config_fn,
altera_status_fn,
altera_done_fn,
altera_write_fn,
altera_abort_fn,
altera_post_fn
};
Altera_desc altera_fpga[CONFIG_FPGA_COUNT] = {
{Altera_CYC2,
passive_serial,
85903,
(void *)&altera_fns,
NULL,
0}
};
/* Initialize the fpga. Return 1 on success, 0 on failure. */
int astro5373l_altera_load(void)
{
int i;
for (i = 0; i < CONFIG_FPGA_COUNT; i++) {
/*
* I did not yet manage to get relocation work properly,
* so set stuff here instead of static initialisation:
*/
altera_fns.pre = altera_pre_fn;
altera_fns.config = altera_config_fn;
altera_fns.status = altera_status_fn;
altera_fns.done = altera_done_fn;
altera_fns.write = altera_write_fn;
altera_fns.abort = altera_abort_fn;
altera_fns.post = altera_post_fn;
altera_fpga[i].iface_fns = (void *)&altera_fns;
fpga_add(fpga_altera, &altera_fpga[i]);
}
return 1;
}
/* Set the FPGA's PROG_B line to the specified level */
int xilinx_pgm_config_fn(int assert, int flush, int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
if (assert)
writeb(0xFB, &gpiop->pclrr_uart);
else
writeb(0x04, &gpiop->ppd_uart);
return assert;
}
/*
* Test the state of the active-low FPGA INIT line. Return 1 on INIT
* asserted (low).
*/
int xilinx_init_config_fn(int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
return (readb(&gpiop->ppd_pwm) & 0x08) == 0;
}
/* Test the state of the active-high FPGA DONE pin */
int xilinx_done_config_fn(int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
return (readb(&gpiop->ppd_pwm) & 0x20) >> 5;
}
/* Abort an FPGA operation */
int xilinx_abort_config_fn(int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
/* ensure all SPI peripherals and FPGAs are deselected */
writeb(0x08, &gpiop->ppd_uart);
writeb(0x01, &gpiop->ppd_timer);
writeb(0x38, &gpiop->ppd_qspi);
return FPGA_FAIL;
}
/*
* FPGA pre-configuration function. Just make sure that
* FPGA reset is asserted to keep the FPGA from starting up after
* configuration.
*/
int xilinx_pre_config_fn(int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
unsigned char tmp_char;
unsigned short tmp_short;
/* first, set the required pins to GPIO function */
/* PAR_T0IN -> GPIO */
tmp_char = readb(&gpiop->par_timer);
tmp_char &= 0xfc;
writeb(tmp_char, &gpiop->par_timer);
/* all QSPI pins -> GPIO */
writew(0x0000, &gpiop->par_qspi);
/* U0RTS, U0CTS -> GPIO */
tmp_short = __raw_readw(&gpiop->par_uart);
tmp_short &= 0xfff3;
__raw_writew(tmp_short, &gpiop->par_uart);
/* all PWM pins -> GPIO */
writeb(0x00, &gpiop->par_pwm);
/* next, set data direction registers */
writeb(0x01, &gpiop->pddr_timer);
writeb(0x25, &gpiop->pddr_qspi);
writeb(0x0c, &gpiop->pddr_uart);
writeb(0x04, &gpiop->pddr_pwm);
/* ensure other SPI peripherals are deselected */
writeb(0x08, &gpiop->ppd_uart);
writeb(0x38, &gpiop->ppd_qspi);
writeb(0x01, &gpiop->ppd_timer);
/* CONFIG = 0, STATUS = 0 -> FPGA in reset state */
writeb(0xFB, &gpiop->pclrr_uart);
/* enable Xilinx configuration by clearing QSPI_CS2 and U0CTS */
writeb(0xF7, &gpiop->pclrr_uart);
writeb(0xDF, &gpiop->pclrr_qspi);
return 0;
}
/*
* FPGA post configuration function. Should perform a test if FPGA is running.
*/
int xilinx_post_config_fn(int cookie)
{
int rc = 0;
/*
* no test yet
*/
return rc;
}
int xilinx_clk_config_fn(int assert_clk, int flush, int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
if (assert_clk)
writeb(0x04, &gpiop->ppd_qspi);
else
writeb(0xFB, &gpiop->pclrr_qspi);
return assert_clk;
}
int xilinx_wr_config_fn(int assert_write, int flush, int cookie)
{
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
if (assert_write)
writeb(0x01, &gpiop->ppd_qspi);
else
writeb(0xFE, &gpiop->pclrr_qspi);
return assert_write;
}
int xilinx_fastwr_config_fn(void *buf, size_t len, int flush, int cookie)
{
size_t bytecount = 0;
gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
unsigned char *data = (unsigned char *)buf;
unsigned char val = 0;
int i;
int len_40 = len / 40;
for (bytecount = 0; bytecount < len; bytecount++) {
val = *(data++);
for (i = 8; i > 0; i--) {
writeb(0xFB, &gpiop->pclrr_qspi);
if (val & 0x80)
writeb(0x01, &gpiop->ppd_qspi);
else
writeb(0xFE, &gpiop->pclrr_qspi);
writeb(0x04, &gpiop->ppd_qspi);
val <<= 1;
}
if (bytecount % len_40 == 0) {
#if defined(CONFIG_HW_WATCHDOG) || defined(CONFIG_WATCHDOG)
WATCHDOG_RESET();
#endif
#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
putc('.'); /* let them know we are alive */
#endif
#ifdef CONFIG_SYS_FPGA_CHECK_CTRLC
if (ctrlc())
return FPGA_FAIL;
#endif
}
}
return FPGA_SUCCESS;
}
/*
* Note that these are pointers to code that is in Flash. They will be
* relocated at runtime.
* FIXME: relocation not yet working for coldfire, see below!
*/
xilinx_spartan3_slave_serial_fns xilinx_fns = {
xilinx_pre_config_fn,
xilinx_pgm_config_fn,
xilinx_clk_config_fn,
xilinx_init_config_fn,
xilinx_done_config_fn,
xilinx_wr_config_fn,
0,
xilinx_fastwr_config_fn
};
xilinx_desc xilinx_fpga[CONFIG_FPGA_COUNT] = {
{xilinx_spartan3,
slave_serial,
XILINX_XC3S4000_SIZE,
(void *)&xilinx_fns,
0,
&spartan3_op}
};
/* Initialize the fpga. Return 1 on success, 0 on failure. */
int astro5373l_xilinx_load(void)
{
int i;
fpga_init();
for (i = 0; i < CONFIG_FPGA_COUNT; i++) {
/*
* I did not yet manage to get relocation work properly,
* so set stuff here instead of static initialisation:
*/
xilinx_fns.pre = xilinx_pre_config_fn;
xilinx_fns.pgm = xilinx_pgm_config_fn;
xilinx_fns.clk = xilinx_clk_config_fn;
xilinx_fns.init = xilinx_init_config_fn;
xilinx_fns.done = xilinx_done_config_fn;
xilinx_fns.wr = xilinx_wr_config_fn;
xilinx_fns.bwr = xilinx_fastwr_config_fn;
xilinx_fpga[i].iface_fns = (void *)&xilinx_fns;
fpga_add(fpga_xilinx, &xilinx_fpga[i]);
}
return 1;
}