/*
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <dt-bindings/input/input.h>

/ {
	cpus {
		cpu@0 {
			cpu0-supply = <&vcc>;
		};
	};

	memory@80000000 {
		device_type = "memory";
		reg = <0x80000000 0>;
	};

	wl12xx_vmmc: wl12xx_vmmc {
		compatible = "regulator-fixed";
		regulator-name = "vwl1271";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		gpio = <&gpio1 3 0>;   /* gpio_3 */
		startup-delay-us = <70000>;
		enable-active-high;
		vin-supply = <&vmmc2>;
	};

	/* HS USB Host PHY on PORT 1 */
	hsusb2_phy: hsusb2_phy {
		compatible = "usb-nop-xceiv";
		reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
		#phy-cells = <0>;
	};
};

&gpmc {
	ranges = <0 0 0x30000000 0x1000000>;	/* CS0: 16MB for NAND */

	nand@0,0 {
		compatible = "ti,omap2-nand";
		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
		interrupt-parent = <&gpmc>;
		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
			     <1 IRQ_TYPE_NONE>;	/* termcount */
		linux,mtd-name = "micron,mt29f4g16abbda3w";
		nand-bus-width = <16>;
		ti,nand-ecc-opt = "bch8";
		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
		gpmc,sync-clk-ps = <0>;
		gpmc,cs-on-ns = <0>;
		gpmc,cs-rd-off-ns = <44>;
		gpmc,cs-wr-off-ns = <44>;
		gpmc,adv-on-ns = <6>;
		gpmc,adv-rd-off-ns = <34>;
		gpmc,adv-wr-off-ns = <44>;
		gpmc,we-off-ns = <40>;
		gpmc,oe-off-ns = <54>;
		gpmc,access-ns = <64>;
		gpmc,rd-cycle-ns = <82>;
		gpmc,wr-cycle-ns = <82>;
		gpmc,wr-access-ns = <40>;
		gpmc,wr-data-mux-bus-ns = <0>;
		gpmc,device-width = <2>;
		#address-cells = <1>;
		#size-cells = <1>;
	};
};

&i2c1 {
	clock-frequency = <2600000>;

	twl: twl@48 {
		reg = <0x48>;
		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
		interrupt-parent = <&intc>;
		twl_audio: audio {
			compatible = "ti,twl4030-audio";
			codec {
			};
		};
	};
};

&i2c2 {
	clock-frequency = <400000>;
};

&i2c3 {
	clock-frequency = <400000>;
};

&mmc3 {
	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
	pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
	pinctrl-names = "default";
	vmmc-supply = <&wl12xx_vmmc>;
	non-removable;
	bus-width = <4>;
	cap-power-off-card;
	#address-cells = <1>;
	#size-cells = <0>;
	wlcore: wlcore@2 {
		compatible = "ti,wl1273";
		reg = <2>;
		interrupt-parent = <&gpio1>;
		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 2 */
		ref-clock-frequency = <26000000>;
	};
};

&usbhshost {
	port2-mode = "ehci-phy";
};

&usbhsehci {
	phys = <0 &hsusb2_phy>;
};


&omap3_pmx_core {
	pinctrl-names = "default";
	pinctrl-0 = <&hsusb2_pins>;

	mmc3_pins: pinmux_mm3_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat4.sdmmc3_dat0 */
			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat2 */
			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat3 */
			OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs2.sdmmc_clk */
		>;
	};
	mcbsp2_pins: pinmux_mcbsp2_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)        /* mcbsp2_clkx */
			OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0)        /* mcbsp2_dr */
			OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)       /* mcbsp2_dx */
		>;
	};
	uart2_pins: pinmux_uart2_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0)	/* uart2_cts.uart2_cts */
			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)	/* uart2_rts .uart2_rts*/
			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)	/* uart2_tx.uart2_tx */
			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)	/* uart2_rx.uart2_rx */
			OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)	/* GPIO_162,BT_EN */
		>;
	};
	mcspi1_pins: pinmux_mcspi1_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)        /* mcspi1_clk.mcspi1_clk */
			OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_simo.mcspi1_simo */
			OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
			OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_cs0.mcspi1_cs0 */
		>;
	};

	hsusb2_pins: pinmux_hsusb2_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi1_cs3.hsusb2_data2 */
			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_clk.hsusb2_data7 */
			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_simo.hsusb2_data4 */
			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_somi.hsusb2_data5 */
			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs0.hsusb2_data6 */
			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs1.hsusb2_data3 */
		>;
	};

	hsusb_otg_pins: pinmux_hsusb_otg_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)	/* hsusb0_clk.hsusb0_clk */
			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)	/* hsusb0_stp.hsusb0_stp */
			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0)	/* hsusb0_data0.hsusb0_data0 */
			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0)	/* hsusb0_data3.hsusb0_data3 */
			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0)	/* hsusb0_data4.hsusb0_data4 */
			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0)	/* hsusb0_data5.hsusb0_data5 */
			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0)	/* hsusb0_data6.hsusb0_data6 */
			OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
		>;
	};


};

&omap3_pmx_wkup {
	pinctrl-names = "default";
	pinctrl-0 = <&hsusb2_reset_pin>;
	hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
		pinctrl-single,pins = <
			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
		>;
	};
	wl127x_gpio: pinmux_wl127x_gpio_pin {
		pinctrl-single,pins = <
			OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
		>;
	};
};

&omap3_pmx_core2 {
	pinctrl-names = "default";
	pinctrl-0 = <&hsusb2_2_pins>;
	hsusb2_2_pins: pinmux_hsusb2_2_pins {
		pinctrl-single,pins = <
			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
		>;
	};
};

&uart2 {
	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
	pinctrl-names = "default";
	pinctrl-0 = <&uart2_pins>;
};

&mcspi1 {
	pinctrl-names = "default";
	pinctrl-0 = <&mcspi1_pins>;
};

#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"

&twl {
	twl_power: power {
		compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
		ti,use_poweroff;
	};
};

&twl_gpio {
	ti,use-leds;
};