/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2014 Freescale Semiconductor, Inc.
 *
 * Configuration settings for the Freescale i.MX6SX Sabreauto board.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include "mx6_common.h"

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)

#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE		UART1_BASE

#define CONFIG_EXTRA_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=zImage\0" \
	"console=ttymxc0\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_file=imx6sx-sabreauto.dtb\0" \
	"fdt_addr=0x88000000\0" \
	"boot_fdt=try\0" \
	"ip_dyn=yes\0" \
	"mmcdev=0\0" \
	"mmcpart=1\0" \
	"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
	"mmcargs=setenv bootargs console=${console},${baudrate} " \
		"root=${mmcroot}\0" \
	"loadbootscript=" \
		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if run loadfdt; then " \
				"bootz ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"if test ${boot_fdt} = try; then " \
					"bootz; " \
				"else " \
					"echo WARN: Cannot load the DT; " \
				"fi; " \
			"fi; " \
		"else " \
			"bootz; " \
		"fi;\0" \
	"netargs=setenv bootargs console=${console},${baudrate} " \
		"root=/dev/nfs " \
	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
		"netboot=echo Booting from net ...; " \
		"run netargs; " \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${image}; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
				"bootz ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"if test ${boot_fdt} = try; then " \
					"bootz; " \
				"else " \
					"echo WARN: Cannot load the DT; " \
				"fi; " \
			"fi; " \
		"else " \
			"bootz; " \
		"fi;\0"

#define CONFIG_BOOTCOMMAND \
	   "mmc dev ${mmcdev};" \
	   "mmc dev ${mmcdev}; if mmc rescan; then " \
		   "if run loadbootscript; then " \
			   "run bootscript; " \
		   "else " \
			   "if run loadimage; then " \
				   "run mmcboot; " \
			   "else run netboot; " \
			   "fi; " \
		   "fi; " \
	   "else run netboot; fi"

/* Miscellaneous configurable options */
#define CONFIG_SYS_MEMTEST_START	0x80000000
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS		1
#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* MMC Configuration */
#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC3_BASE_ADDR

/* I2C Configs */
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED		  100000

/* NAND stuff */
#define CONFIG_SYS_MAX_NAND_DEVICE     1
#define CONFIG_SYS_NAND_BASE           0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION

/* DMA stuff, needed for GPMI/MXS NAND support */

/* Network */

#define CONFIG_FEC_MXC
#define CONFIG_MII

#define IMX_FEC_BASE			ENET2_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR          0x0

#define CONFIG_FEC_XCV_TYPE             RGMII
#define CONFIG_ETHPRIME                 "FEC"

#define CONFIG_PHY_ATHEROS

#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS   0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#endif

#define CONFIG_IMX_THERMAL

#ifdef CONFIG_FSL_QSPI
#define CONFIG_SYS_FSL_QSPI_AHB
#define CONFIG_SF_DEFAULT_BUS		0
#define CONFIG_SF_DEFAULT_CS		0
#define CONFIG_SF_DEFAULT_SPEED	40000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
#define FSL_QSPI_FLASH_SIZE		SZ_32M
#define FSL_QSPI_FLASH_NUM		2
#endif

#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
#define CONFIG_ENV_SIZE			SZ_8K

#define CONFIG_SYS_FSL_USDHC_NUM	2
#if defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_SYS_MMC_ENV_DEV		0  /*USDHC3*/
#endif

#endif				/* __CONFIG_H */