blob: dfdad56dcc927fea69cc661384e1224918d5d04e [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2009
* Net Insight <www.netinsight.net>
* Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
*
* Based on sheevaplug.h:
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
*/
#ifndef _CONFIG_OPENRD_H
#define _CONFIG_OPENRD_H
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
#define CONFIG_KW88F6281 1 /* SOC Name */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/*
* Commands configuration
*/
#define CONFIG_SYS_MVFS
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
/*
* Environment variables configurations
*/
#ifdef CONFIG_CMD_NAND
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
#endif
/*
* max 4k env size is enough, but in case of nand
* it has to be rounded to sector size
*/
#define CONFIG_ENV_SIZE 0x20000 /* 128k */
#define CONFIG_ENV_ADDR 0x60000
#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
/*
* Environment is right behind U-Boot in flash. Make sure U-Boot
* doesn't grow into the environment area.
*/
#define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET
/*
* Default environment variables
*/
#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
"setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
"${x_bootcmd_usb}; bootm 0x6400000;"
#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console=ttyS0,115200 " \
CONFIG_MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
"x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
"x_bootcmd_usb=usb start\0" \
"x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
"mtdids="CONFIG_MTDIDS_DEFAULT"\0" \
"mtdparts="CONFIG_MTDPARTS_DEFAULT"\0"
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
# ifdef CONFIG_BOARD_IS_OPENRD_BASE
# define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
# else
# define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */
# endif
# ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE
# define CONFIG_PHY_BASE_ADR 0x0
# define PHY_NO "88E1121"
# else
# define CONFIG_PHY_BASE_ADR 0x8
# define PHY_NO "88E1116"
# endif
#endif /* CONFIG_CMD_NET */
/*
* SATA Driver configuration
*/
#ifdef CONFIG_MVSATA_IDE
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
#endif /*CONFIG_MVSATA_IDE*/
#ifdef CONFIG_CMD_MMC
#define CONFIG_MVEBU_MMC
#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
#endif /* CONFIG_CMD_MMC */
#endif /* _CONFIG_OPENRD_BASE_H */