| /* | |
| * (C) Copyright 2007-2008 | |
| * Stelian Pop <stelian@popies.net> | |
| * Lead Tech Design <www.leadtechdesign.com> | |
| * | |
| * SPDX-License-Identifier: GPL-2.0+ | |
| */ | |
| #include <common.h> | |
| #include <asm/io.h> | |
| #include <asm/arch/at91sam9261.h> | |
| #include <asm/arch/at91sam9261_matrix.h> | |
| #include <asm/arch/at91sam9_smc.h> | |
| #include <asm/arch/at91_common.h> | |
| #include <asm/arch/at91_pmc.h> | |
| #include <asm/arch/at91_rstc.h> | |
| #include <asm/arch/clk.h> | |
| #include <asm/arch/gpio.h> | |
| #include <lcd.h> | |
| #include <atmel_lcdc.h> | |
| #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000) | |
| #include <net.h> | |
| #include <netdev.h> | |
| #endif | |
| DECLARE_GLOBAL_DATA_PTR; | |
| /* ------------------------------------------------------------------------- */ | |
| /* | |
| * Miscelaneous platform dependent initialisations | |
| */ | |
| #ifdef CONFIG_CMD_NAND | |
| static void at91sam9261ek_nand_hw_init(void) | |
| { | |
| struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; | |
| struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; | |
| struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; | |
| unsigned long csa; | |
| /* Enable CS3 */ | |
| csa = readl(&matrix->ebicsa); | |
| csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA; | |
| writel(csa, &matrix->ebicsa); | |
| /* Configure SMC CS3 for NAND/SmartMedia */ | |
| #ifdef CONFIG_AT91SAM9G10EK | |
| writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) | | |
| AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), | |
| &smc->cs[3].setup); | |
| writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) | | |
| AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7), | |
| &smc->cs[3].pulse); | |
| writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7), | |
| &smc->cs[3].cycle); | |
| #else | |
| writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | | |
| AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), | |
| &smc->cs[3].setup); | |
| writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | | |
| AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), | |
| &smc->cs[3].pulse); | |
| writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), | |
| &smc->cs[3].cycle); | |
| #endif | |
| writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | | |
| AT91_SMC_MODE_EXNW_DISABLE | | |
| #ifdef CONFIG_SYS_NAND_DBW_16 | |
| AT91_SMC_MODE_DBW_16 | | |
| #else /* CONFIG_SYS_NAND_DBW_8 */ | |
| AT91_SMC_MODE_DBW_8 | | |
| #endif | |
| AT91_SMC_MODE_TDF_CYCLE(2), | |
| &smc->cs[3].mode); | |
| writel(1 << ATMEL_ID_PIOC, &pmc->pcer); | |
| /* Configure RDY/BSY */ | |
| at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); | |
| /* Enable NandFlash */ | |
| at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); | |
| at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */ | |
| at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */ | |
| } | |
| #endif | |
| #ifdef CONFIG_DRIVER_DM9000 | |
| static void at91sam9261ek_dm9000_hw_init(void) | |
| { | |
| struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; | |
| /* Configure SMC CS2 for DM9000 */ | |
| #ifdef CONFIG_AT91SAM9G10EK | |
| writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) | | |
| AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0), | |
| &smc->cs[2].setup); | |
| writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) | | |
| AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8), | |
| &smc->cs[2].pulse); | |
| writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20), | |
| &smc->cs[2].cycle); | |
| writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | | |
| AT91_SMC_MODE_EXNW_DISABLE | | |
| AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | | |
| AT91_SMC_MODE_TDF_CYCLE(1), | |
| &smc->cs[2].mode); | |
| #else | |
| writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) | | |
| AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), | |
| &smc->cs[2].setup); | |
| writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) | | |
| AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8), | |
| &smc->cs[2].pulse); | |
| writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16), | |
| &smc->cs[2].cycle); | |
| writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | | |
| AT91_SMC_MODE_EXNW_DISABLE | | |
| AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | | |
| AT91_SMC_MODE_TDF_CYCLE(1), | |
| &smc->cs[2].mode); | |
| #endif | |
| /* Configure Reset signal as output */ | |
| at91_set_gpio_output(AT91_PIN_PC10, 0); | |
| /* Configure Interrupt pin as input, no pull-up */ | |
| at91_set_gpio_input(AT91_PIN_PC11, 0); | |
| } | |
| #endif | |
| #ifdef CONFIG_LCD | |
| vidinfo_t panel_info = { | |
| .vl_col = 240, | |
| .vl_row = 320, | |
| .vl_clk = 4965000, | |
| .vl_sync = ATMEL_LCDC_INVLINE_INVERTED | | |
| ATMEL_LCDC_INVFRAME_INVERTED, | |
| .vl_bpix = 3, | |
| .vl_tft = 1, | |
| .vl_hsync_len = 5, | |
| .vl_left_margin = 1, | |
| .vl_right_margin = 33, | |
| .vl_vsync_len = 1, | |
| .vl_upper_margin = 1, | |
| .vl_lower_margin = 0, | |
| .mmio = ATMEL_BASE_LCDC, | |
| }; | |
| void lcd_enable(void) | |
| { | |
| at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */ | |
| } | |
| void lcd_disable(void) | |
| { | |
| at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */ | |
| } | |
| static void at91sam9261ek_lcd_hw_init(void) | |
| { | |
| struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; | |
| at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */ | |
| at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */ | |
| at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */ | |
| at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */ | |
| at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */ | |
| at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */ | |
| at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */ | |
| at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */ | |
| at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */ | |
| at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */ | |
| at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */ | |
| at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */ | |
| at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */ | |
| at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */ | |
| at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */ | |
| at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */ | |
| at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */ | |
| at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */ | |
| at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */ | |
| at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */ | |
| at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */ | |
| at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */ | |
| writel(AT91_PMC_HCK1, &pmc->scer); | |
| /* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */ | |
| #ifdef CONFIG_AT91SAM9261EK | |
| gd->fb_base = ATMEL_BASE_SRAM; | |
| #endif | |
| } | |
| #ifdef CONFIG_LCD_INFO | |
| #include <nand.h> | |
| #include <version.h> | |
| void lcd_show_board_info(void) | |
| { | |
| ulong dram_size, nand_size; | |
| int i; | |
| char temp[32]; | |
| lcd_printf ("%s\n", U_BOOT_VERSION); | |
| lcd_printf ("(C) 2008 ATMEL Corp\n"); | |
| lcd_printf ("at91support@atmel.com\n"); | |
| lcd_printf ("%s CPU at %s MHz\n", | |
| ATMEL_CPU_NAME, | |
| strmhz(temp, get_cpu_clk_rate())); | |
| dram_size = 0; | |
| for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) | |
| dram_size += gd->bd->bi_dram[i].size; | |
| nand_size = 0; | |
| for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) | |
| nand_size += nand_info[i].size; | |
| lcd_printf (" %ld MB SDRAM, %ld MB NAND\n", | |
| dram_size >> 20, | |
| nand_size >> 20 ); | |
| } | |
| #endif /* CONFIG_LCD_INFO */ | |
| #endif | |
| int board_init(void) | |
| { | |
| #ifdef CONFIG_AT91SAM9G10EK | |
| /* arch number of AT91SAM9G10EK-Board */ | |
| gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK; | |
| #else | |
| /* arch number of AT91SAM9261EK-Board */ | |
| gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK; | |
| #endif | |
| /* adress of boot parameters */ | |
| gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; | |
| at91_seriald_hw_init(); | |
| #ifdef CONFIG_CMD_NAND | |
| at91sam9261ek_nand_hw_init(); | |
| #endif | |
| #ifdef CONFIG_HAS_DATAFLASH | |
| at91_spi0_hw_init(1 << 0); | |
| #endif | |
| #ifdef CONFIG_DRIVER_DM9000 | |
| at91sam9261ek_dm9000_hw_init(); | |
| #endif | |
| #ifdef CONFIG_LCD | |
| at91sam9261ek_lcd_hw_init(); | |
| #endif | |
| return 0; | |
| } | |
| #ifdef CONFIG_DRIVER_DM9000 | |
| int board_eth_init(bd_t *bis) | |
| { | |
| return dm9000_initialize(bis); | |
| } | |
| #endif | |
| int dram_init(void) | |
| { | |
| gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, | |
| CONFIG_SYS_SDRAM_SIZE); | |
| return 0; | |
| } | |
| #ifdef CONFIG_RESET_PHY_R | |
| void reset_phy(void) | |
| { | |
| #ifdef CONFIG_DRIVER_DM9000 | |
| /* | |
| * Initialize ethernet HW addr prior to starting Linux, | |
| * needed for nfsroot | |
| */ | |
| eth_init(gd->bd); | |
| #endif | |
| } | |
| #endif |