drivers/i2c/omap24xx_i2c.c - u-boot - Git at Google

 /*
  * Basic I2C functions
  *
  * Copyright (c) 2004 Texas Instruments
  *
  * This package is free software;  you can redistribute it and/or
  * modify it under the terms of the license found in the file
  * named COPYING that should have accompanied this file.
  *
  * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
  * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
  * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  *
  * Author: Jian Zhang jzhang@ti.com, Texas Instruments
  *
  * Copyright (c) 2003 Wolfgang Denk, wd@denx.de
  * Rewritten to fit into the current U-Boot framework
  *
  * Adapted for OMAP2420 I2C, r-woodruff2@ti.com
  *
  * Copyright (c) 2013 Lubomir Popov <lpopov@mm-sol.com>, MM Solutions
  * New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4
  * (4430/60/70), OMAP5 (5430) and AM335X (3359); should work on older
  * OMAPs and derivatives as well. The only anticipated exception would
  * be the OMAP2420, which shall require driver modification.
  * - Rewritten i2c_read to operate correctly with all types of chips
  *   (old function could not read consistent data from some I2C slaves).
  * - Optimized i2c_write.
  * - New i2c_probe, performs write access vs read. The old probe could
  *   hang the system under certain conditions (e.g. unconfigured pads).
  * - The read/write/probe functions try to identify unconfigured bus.
  * - Status functions now read irqstatus_raw as per TRM guidelines
  *   (except for OMAP243X and OMAP34XX).
  * - Driver now supports up to I2C5 (OMAP5).
  *
  * Copyright (c) 2014 Hannes Petermaier <oe5hpm@oevsv.at>, B&R
  * - Added support for set_speed
  *
  */

 #include <common.h>
 #include <i2c.h>

 #include <asm/arch/i2c.h>
 #include <asm/io.h>

 #include "omap24xx_i2c.h"

 DECLARE_GLOBAL_DATA_PTR;

 #define I2C_TIMEOUT	1000

 /* Absolutely safe for status update at 100 kHz I2C: */
 #define I2C_WAIT	200

 static int wait_for_bb(struct i2c_adapter *adap);
 static struct i2c *omap24_get_base(struct i2c_adapter *adap);
 static u16 wait_for_event(struct i2c_adapter *adap);
 static void flush_fifo(struct i2c_adapter *adap);
 static int omap24_i2c_findpsc(u32 *pscl, u32 *psch, uint speed)
 {
 	unsigned int sampleclk, prescaler;
 	int fsscll, fssclh;

 	speed <<= 1;
 	prescaler = 0;
 	/*
 	 * some divisors may cause a precission loss, but shouldn't
 	 * be a big thing, because i2c_clk is then allready very slow.
 	 */
 	while (prescaler <= 0xFF) {
 		sampleclk = I2C_IP_CLK / (prescaler+1);

 		fsscll = sampleclk / speed;
 		fssclh = fsscll;
 		fsscll -= I2C_FASTSPEED_SCLL_TRIM;
 		fssclh -= I2C_FASTSPEED_SCLH_TRIM;

 		if (((fsscll > 0) && (fssclh > 0)) &&
 		    ((fsscll <= (255-I2C_FASTSPEED_SCLL_TRIM)) &&
 		    (fssclh <= (255-I2C_FASTSPEED_SCLH_TRIM)))) {
 			if (pscl)
 				*pscl = fsscll;
 			if (psch)
 				*psch = fssclh;

 			return prescaler;
 		}
 		prescaler++;
 	}
 	return -1;
 }
 static uint omap24_i2c_setspeed(struct i2c_adapter *adap, uint speed)
 {
 	struct i2c *i2c_base = omap24_get_base(adap);
 	int psc, fsscll = 0, fssclh = 0;
 	int hsscll = 0, hssclh = 0;
 	u32 scll = 0, sclh = 0;

 	if (speed >= OMAP_I2C_HIGH_SPEED) {
 		/* High speed */
 		psc = I2C_IP_CLK / I2C_INTERNAL_SAMPLING_CLK;
 		psc -= 1;
 		if (psc < I2C_PSC_MIN) {
 			printf("Error : I2C unsupported prescaler %d\n", psc);
 			return -1;
 		}

 		/* For first phase of HS mode */
 		fsscll = I2C_INTERNAL_SAMPLING_CLK / (2 * speed);

 		fssclh = fsscll;

 		fsscll -= I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM;
 		fssclh -= I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM;
 		if (((fsscll < 0) || (fssclh < 0)) ||
 		    ((fsscll > 255) || (fssclh > 255))) {
 			puts("Error : I2C initializing first phase clock\n");
 			return -1;
 		}

 		/* For second phase of HS mode */
 		hsscll = hssclh = I2C_INTERNAL_SAMPLING_CLK / (2 * speed);

 		hsscll -= I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM;
 		hssclh -= I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM;
 		if (((fsscll < 0) || (fssclh < 0)) ||
 		    ((fsscll > 255) || (fssclh > 255))) {
 			puts("Error : I2C initializing second phase clock\n");
 			return -1;
 		}

 		scll = (unsigned int)hsscll << 8 | (unsigned int)fsscll;
 		sclh = (unsigned int)hssclh << 8 | (unsigned int)fssclh;

 	} else {
 		/* Standard and fast speed */
 		psc = omap24_i2c_findpsc(&scll, &sclh, speed);
 		if (0 > psc) {
 			puts("Error : I2C initializing clock\n");
 			return -1;
 		}
 	}

 	adap->speed	= speed;
 	adap->waitdelay = (10000000 / speed) * 2; /* wait for 20 clkperiods */
 	writew(0, &i2c_base->con);
 	writew(psc, &i2c_base->psc);
 	writew(scll, &i2c_base->scll);
 	writew(sclh, &i2c_base->sclh);
 	writew(I2C_CON_EN, &i2c_base->con);
 	writew(0xFFFF, &i2c_base->stat);	/* clear all pending status */

 	return 0;
 }

 static void omap24_i2c_deblock(struct i2c_adapter *adap)
 {
 	struct i2c *i2c_base = omap24_get_base(adap);
 	int i;
 	u16 systest;
 	u16 orgsystest;

 	/* set test mode ST_EN = 1 */
 	orgsystest = readw(&i2c_base->systest);
 	systest = orgsystest;
 	/* enable testmode */
 	systest |= I2C_SYSTEST_ST_EN;
 	writew(systest, &i2c_base->systest);
 	systest &= ~I2C_SYSTEST_TMODE_MASK;
 	systest |= 3 << I2C_SYSTEST_TMODE_SHIFT;
 	writew(systest, &i2c_base->systest);

 	/* set SCL, SDA  = 1 */
 	systest |= I2C_SYSTEST_SCL_O | I2C_SYSTEST_SDA_O;
 	writew(systest, &i2c_base->systest);
 	udelay(10);

 	/* toggle scl 9 clocks */
 	for (i = 0; i < 9; i++) {
 		/* SCL = 0 */
 		systest &= ~I2C_SYSTEST_SCL_O;
 		writew(systest, &i2c_base->systest);
 		udelay(10);
 		/* SCL = 1 */
 		systest |= I2C_SYSTEST_SCL_O;
 		writew(systest, &i2c_base->systest);
 		udelay(10);
 	}

 	/* send stop */
 	systest &= ~I2C_SYSTEST_SDA_O;
 	writew(systest, &i2c_base->systest);
 	udelay(10);
 	systest |= I2C_SYSTEST_SCL_O | I2C_SYSTEST_SDA_O;
 	writew(systest, &i2c_base->systest);
 	udelay(10);

 	/* restore original mode */
 	writew(orgsystest, &i2c_base->systest);
 }

 static void omap24_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
 {
 	struct i2c *i2c_base = omap24_get_base(adap);
 	int timeout = I2C_TIMEOUT;
 	int deblock = 1;

 retry:
 	if (readw(&i2c_base->con) & I2C_CON_EN) {
 		writew(0, &i2c_base->con);
 		udelay(50000);
 	}

 	writew(0x2, &i2c_base->sysc); /* for ES2 after soft reset */
 	udelay(1000);

 	writew(I2C_CON_EN, &i2c_base->con);
 	while (!(readw(&i2c_base->syss) & I2C_SYSS_RDONE) && timeout--) {
 		if (timeout <= 0) {
 			puts("ERROR: Timeout in soft-reset\n");
 			return;
 		}
 		udelay(1000);
 	}

 	if (0 != omap24_i2c_setspeed(adap, speed)) {
 		printf("ERROR: failed to setup I2C bus-speed!\n");
 		return;
 	}

 	/* own address */
 	writew(slaveadd, &i2c_base->oa);

 #if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
 	/*
 	 * Have to enable interrupts for OMAP2/3, these IPs don't have
 	 * an 'irqstatus_raw' register and we shall have to poll 'stat'
 	 */
 	writew(I2C_IE_XRDY_IE | I2C_IE_RRDY_IE | I2C_IE_ARDY_IE |
 	       I2C_IE_NACK_IE | I2C_IE_AL_IE, &i2c_base->ie);
 #endif
 	udelay(1000);
 	flush_fifo(adap);
 	writew(0xFFFF, &i2c_base->stat);

 	/* Handle possible failed I2C state */
 	if (wait_for_bb(adap))
 		if (deblock == 1) {
 			omap24_i2c_deblock(adap);
 			deblock = 0;
 			goto retry;
 		}
 }

 static void flush_fifo(struct i2c_adapter *adap)
 {
 	struct i2c *i2c_base = omap24_get_base(adap);
 	u16 stat;

 	/*
 	 * note: if you try and read data when its not there or ready
 	 * you get a bus error
 	 */
 	while (1) {
 		stat = readw(&i2c_base->stat);
 		if (stat == I2C_STAT_RRDY) {
 			readb(&i2c_base->data);
 			writew(I2C_STAT_RRDY, &i2c_base->stat);
 			udelay(1000);
 		} else
 			break;
 	}
 }

 /*
  * i2c_probe: Use write access. Allows to identify addresses that are
  *            write-only (like the config register of dual-port EEPROMs)
  */
 static int omap24_i2c_probe(struct i2c_adapter *adap, uchar chip)
 {
 	struct i2c *i2c_base = omap24_get_base(adap);
 	u16 status;
 	int res = 1; /* default = fail */

 	if (chip == readw(&i2c_base->oa))
 		return res;

 	/* Wait until bus is free */
 	if (wait_for_bb(adap))
 		return res;

 	/* No data transfer, slave addr only */
 	writew(chip, &i2c_base->sa);
 	/* Stop bit needed here */
 	writew(I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX |
 	       I2C_CON_STP, &i2c_base->con);

 	status = wait_for_event(adap);

 	if ((status & ~I2C_STAT_XRDY) == 0 || (status & I2C_STAT_AL)) {
 		/*
 		 * With current high-level command implementation, notifying
 		 * the user shall flood the console with 127 messages. If
 		 * silent exit is desired upon unconfigured bus, remove the
 		 * following 'if' section:
 		 */
 		if (status == I2C_STAT_XRDY)
 			printf("i2c_probe: pads on bus %d probably not configured (status=0x%x)\n",
 			       adap->hwadapnr, status);

 		goto pr_exit;
 	}

 	/* Check for ACK (!NAK) */
 	if (!(status & I2C_STAT_NACK)) {
 		res = 0;				/* Device found */
 		udelay(adap->waitdelay);/* Required by AM335X in SPL */
 		/* Abort transfer (force idle state) */
 		writew(I2C_CON_MST | I2C_CON_TRX, &i2c_base->con); /* Reset */
 		udelay(1000);
 		writew(I2C_CON_EN | I2C_CON_MST | I2C_CON_TRX |
 		       I2C_CON_STP, &i2c_base->con);		/* STP */
 	}
 pr_exit:
 	flush_fifo(adap);
 	writew(0xFFFF, &i2c_base->stat);
 	return res;
 }

 /*
  * i2c_read: Function now uses a single I2C read transaction with bulk transfer
  *           of the requested number of bytes (note that the 'i2c md' command
  *           limits this to 16 bytes anyway). If CONFIG_I2C_REPEATED_START is
  *           defined in the board config header, this transaction shall be with
  *           Repeated Start (Sr) between the address and data phases; otherwise
  *           Stop-Start (P-S) shall be used (some I2C chips do require a P-S).
  *           The address (reg offset) may be 0, 1 or 2 bytes long.
  *           Function now reads correctly from chips that return more than one
  *           byte of data per addressed register (like TI temperature sensors),
  *           or that do not need a register address at all (such as some clock
  *           distributors).
  */
 static int omap24_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
 			   int alen, uchar *buffer, int len)
 {
 	struct i2c *i2c_base = omap24_get_base(adap);
 	int i2c_error = 0;
 	u16 status;

 	if (alen < 0) {
 		puts("I2C read: addr len < 0\n");
 		return 1;
 	}
 	if (len < 0) {
 		puts("I2C read: data len < 0\n");
 		return 1;
 	}
 	if (buffer == NULL) {
 		puts("I2C read: NULL pointer passed\n");
 		return 1;
 	}

 	if (alen > 2) {
 		printf("I2C read: addr len %d not supported\n", alen);
 		return 1;
 	}

 	if (addr + len > (1 << 16)) {
 		puts("I2C read: address out of range\n");
 		return 1;
 	}

 	/* Wait until bus not busy */
 	if (wait_for_bb(adap))
 		return 1;

 	/* Zero, one or two bytes reg address (offset) */
 	writew(alen, &i2c_base->cnt);
 	/* Set slave address */
 	writew(chip, &i2c_base->sa);

 	if (alen) {
 		/* Must write reg offset first */
 #ifdef CONFIG_I2C_REPEATED_START
 		/* No stop bit, use Repeated Start (Sr) */
 		writew(I2C_CON_EN | I2C_CON_MST | I2C_CON_STT |
 		       I2C_CON_TRX, &i2c_base->con);
 #else
 		/* Stop - Start (P-S) */
 		writew(I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP |
 		       I2C_CON_TRX, &i2c_base->con);
 #endif
 		/* Send register offset */
 		while (1) {
 			status = wait_for_event(adap);
 			/* Try to identify bus that is not padconf'd for I2C */
 			if (status == I2C_STAT_XRDY) {
 				i2c_error = 2;
 				printf("i2c_read (addr phase): pads on bus %d probably not configured (status=0x%x)\n",
 				       adap->hwadapnr, status);
 				goto rd_exit;
 			}
 			if (status == 0 || (status & I2C_STAT_NACK)) {
 				i2c_error = 1;
 				printf("i2c_read: error waiting for addr ACK (status=0x%x)\n",
 				       status);
 				goto rd_exit;
 			}
 			if (alen) {
 				if (status & I2C_STAT_XRDY) {
 					alen--;
 					/* Do we have to use byte access? */
 					writeb((addr >> (8 * alen)) & 0xff,
 					       &i2c_base->data);
 					writew(I2C_STAT_XRDY, &i2c_base->stat);
 				}
 			}
 			if (status & I2C_STAT_ARDY) {
 				writew(I2C_STAT_ARDY, &i2c_base->stat);
 				break;
 			}
 		}
 	}
 	/* Set slave address */
 	writew(chip, &i2c_base->sa);
 	/* Read len bytes from slave */
 	writew(len, &i2c_base->cnt);
 	/* Need stop bit here */
 	writew(I2C_CON_EN | I2C_CON_MST |
 	       I2C_CON_STT | I2C_CON_STP,
 	       &i2c_base->con);

 	/* Receive data */
 	while (1) {
 		status = wait_for_event(adap);
 		/*
 		 * Try to identify bus that is not padconf'd for I2C. This
 		 * state could be left over from previous transactions if
 		 * the address phase is skipped due to alen=0.
 		 */
 		if (status == I2C_STAT_XRDY) {
 			i2c_error = 2;
 			printf("i2c_read (data phase): pads on bus %d probably not configured (status=0x%x)\n",
 			       adap->hwadapnr, status);
 			goto rd_exit;
 		}
 		if (status == 0 || (status & I2C_STAT_NACK)) {
 			i2c_error = 1;
 			goto rd_exit;
 		}
 		if (status & I2C_STAT_RRDY) {
 			*buffer++ = readb(&i2c_base->data);
 			writew(I2C_STAT_RRDY, &i2c_base->stat);
 		}
 		if (status & I2C_STAT_ARDY) {
 			writew(I2C_STAT_ARDY, &i2c_base->stat);
 			break;
 		}
 	}

 rd_exit:
 	flush_fifo(adap);
 	writew(0xFFFF, &i2c_base->stat);
 	return i2c_error;
 }

 /* i2c_write: Address (reg offset) may be 0, 1 or 2 bytes long. */
 static int omap24_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
 			    int alen, uchar *buffer, int len)
 {
 	struct i2c *i2c_base = omap24_get_base(adap);
 	int i;
 	u16 status;
 	int i2c_error = 0;
 	int timeout = I2C_TIMEOUT;

 	if (alen < 0) {
 		puts("I2C write: addr len < 0\n");
 		return 1;
 	}

 	if (len < 0) {
 		puts("I2C write: data len < 0\n");
 		return 1;
 	}

 	if (buffer == NULL) {
 		puts("I2C write: NULL pointer passed\n");
 		return 1;
 	}

 	if (alen > 2) {
 		printf("I2C write: addr len %d not supported\n", alen);
 		return 1;
 	}

 	if (addr + len > (1 << 16)) {
 		printf("I2C write: address 0x%x + 0x%x out of range\n",
 		       addr, len);
 		return 1;
 	}

 	/* Wait until bus not busy */
 	if (wait_for_bb(adap))
 		return 1;

 	/* Start address phase - will write regoffset + len bytes data */
 	writew(alen + len, &i2c_base->cnt);
 	/* Set slave address */
 	writew(chip, &i2c_base->sa);
 	/* Stop bit needed here */
 	writew(I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX |
 	       I2C_CON_STP, &i2c_base->con);

 	while (alen) {
 		/* Must write reg offset (one or two bytes) */
 		status = wait_for_event(adap);
 		/* Try to identify bus that is not padconf'd for I2C */
 		if (status == I2C_STAT_XRDY) {
 			i2c_error = 2;
 			printf("i2c_write: pads on bus %d probably not configured (status=0x%x)\n",
 			       adap->hwadapnr, status);
 			goto wr_exit;
 		}
 		if (status == 0 || (status & I2C_STAT_NACK)) {
 			i2c_error = 1;
 			printf("i2c_write: error waiting for addr ACK (status=0x%x)\n",
 			       status);
 			goto wr_exit;
 		}
 		if (status & I2C_STAT_XRDY) {
 			alen--;
 			writeb((addr >> (8 * alen)) & 0xff, &i2c_base->data);
 			writew(I2C_STAT_XRDY, &i2c_base->stat);
 		} else {
 			i2c_error = 1;
 			printf("i2c_write: bus not ready for addr Tx (status=0x%x)\n",
 			       status);
 			goto wr_exit;
 		}
 	}
 	/* Address phase is over, now write data */
 	for (i = 0; i < len; i++) {
 		status = wait_for_event(adap);
 		if (status == 0 || (status & I2C_STAT_NACK)) {
 			i2c_error = 1;
 			printf("i2c_write: error waiting for data ACK (status=0x%x)\n",
 			       status);
 			goto wr_exit;
 		}
 		if (status & I2C_STAT_XRDY) {
 			writeb(buffer[i], &i2c_base->data);
 			writew(I2C_STAT_XRDY, &i2c_base->stat);
 		} else {
 			i2c_error = 1;
 			printf("i2c_write: bus not ready for data Tx (i=%d)\n",
 			       i);
 			goto wr_exit;
 		}
 	}
 	/*
 	 * poll ARDY bit for making sure that last byte really has been
 	 * transferred on the bus.
 	 */
 	do {
 		status = wait_for_event(adap);
 	} while (!(status & I2C_STAT_ARDY) && timeout--);
 	if (timeout <= 0)
 		printf("i2c_write: timed out writig last byte!\n");

 wr_exit:
 	flush_fifo(adap);
 	writew(0xFFFF, &i2c_base->stat);
 	return i2c_error;
 }

 /*
  * Wait for the bus to be free by checking the Bus Busy (BB)
  * bit to become clear
  */
 static int wait_for_bb(struct i2c_adapter *adap)
 {
 	struct i2c *i2c_base = omap24_get_base(adap);
 	int timeout = I2C_TIMEOUT;
 	u16 stat;

 	writew(0xFFFF, &i2c_base->stat);	/* clear current interrupts...*/
 #if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
 	while ((stat = readw(&i2c_base->stat) & I2C_STAT_BB) && timeout--) {
 #else
 	/* Read RAW status */
 	while ((stat = readw(&i2c_base->irqstatus_raw) &
 		I2C_STAT_BB) && timeout--) {
 #endif
 		writew(stat, &i2c_base->stat);
 		udelay(adap->waitdelay);
 	}

 	if (timeout <= 0) {
 		printf("Timed out in wait_for_bb: status=%04x\n",
 		       stat);
 		return 1;
 	}
 	writew(0xFFFF, &i2c_base->stat);	 /* clear delayed stuff*/
 	return 0;
 }

 /*
  * Wait for the I2C controller to complete current action
  * and update status
  */
 static u16 wait_for_event(struct i2c_adapter *adap)
 {
 	struct i2c *i2c_base = omap24_get_base(adap);
 	u16 status;
 	int timeout = I2C_TIMEOUT;

 	do {
 		udelay(adap->waitdelay);
 #if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
 		status = readw(&i2c_base->stat);
 #else
 		/* Read RAW status */
 		status = readw(&i2c_base->irqstatus_raw);
 #endif
 	} while (!(status &
 		   (I2C_STAT_ROVR | I2C_STAT_XUDF | I2C_STAT_XRDY |
 		    I2C_STAT_RRDY | I2C_STAT_ARDY | I2C_STAT_NACK |
 		    I2C_STAT_AL)) && timeout--);

 	if (timeout <= 0) {
 		printf("Timed out in wait_for_event: status=%04x\n",
 		       status);
 		/*
 		 * If status is still 0 here, probably the bus pads have
 		 * not been configured for I2C, and/or pull-ups are missing.
 		 */
 		printf("Check if pads/pull-ups of bus %d are properly configured\n",
 		       adap->hwadapnr);
 		writew(0xFFFF, &i2c_base->stat);
 		status = 0;
 	}

 	return status;
 }

 static struct i2c *omap24_get_base(struct i2c_adapter *adap)
 {
 	switch (adap->hwadapnr) {
 	case 0:
 		return (struct i2c *)I2C_BASE1;
 		break;
 	case 1:
 		return (struct i2c *)I2C_BASE2;
 		break;
 #if (I2C_BUS_MAX > 2)
 	case 2:
 		return (struct i2c *)I2C_BASE3;
 		break;
 #if (I2C_BUS_MAX > 3)
 	case 3:
 		return (struct i2c *)I2C_BASE4;
 		break;
 #if (I2C_BUS_MAX > 4)
 	case 4:
 		return (struct i2c *)I2C_BASE5;
 		break;
 #endif
 #endif
 #endif
 	default:
 		printf("wrong hwadapnr: %d\n", adap->hwadapnr);
 		break;
 	}
 	return NULL;
 }

 #if !defined(CONFIG_SYS_OMAP24_I2C_SPEED1)
 #define CONFIG_SYS_OMAP24_I2C_SPEED1 CONFIG_SYS_OMAP24_I2C_SPEED
 #endif
 #if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE1)
 #define CONFIG_SYS_OMAP24_I2C_SLAVE1 CONFIG_SYS_OMAP24_I2C_SLAVE
 #endif

 U_BOOT_I2C_ADAP_COMPLETE(omap24_0, omap24_i2c_init, omap24_i2c_probe,
 			 omap24_i2c_read, omap24_i2c_write, omap24_i2c_setspeed,
 			 CONFIG_SYS_OMAP24_I2C_SPEED,
 			 CONFIG_SYS_OMAP24_I2C_SLAVE,
 			 0)
 U_BOOT_I2C_ADAP_COMPLETE(omap24_1, omap24_i2c_init, omap24_i2c_probe,
 			 omap24_i2c_read, omap24_i2c_write, omap24_i2c_setspeed,
 			 CONFIG_SYS_OMAP24_I2C_SPEED1,
 			 CONFIG_SYS_OMAP24_I2C_SLAVE1,
 			 1)
 #if (I2C_BUS_MAX > 2)
 #if !defined(CONFIG_SYS_OMAP24_I2C_SPEED2)
 #define CONFIG_SYS_OMAP24_I2C_SPEED2 CONFIG_SYS_OMAP24_I2C_SPEED
 #endif
 #if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE2)
 #define CONFIG_SYS_OMAP24_I2C_SLAVE2 CONFIG_SYS_OMAP24_I2C_SLAVE
 #endif

 U_BOOT_I2C_ADAP_COMPLETE(omap24_2, omap24_i2c_init, omap24_i2c_probe,
 			 omap24_i2c_read, omap24_i2c_write, NULL,
 			 CONFIG_SYS_OMAP24_I2C_SPEED2,
 			 CONFIG_SYS_OMAP24_I2C_SLAVE2,
 			 2)
 #if (I2C_BUS_MAX > 3)
 #if !defined(CONFIG_SYS_OMAP24_I2C_SPEED3)
 #define CONFIG_SYS_OMAP24_I2C_SPEED3 CONFIG_SYS_OMAP24_I2C_SPEED
 #endif
 #if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE3)
 #define CONFIG_SYS_OMAP24_I2C_SLAVE3 CONFIG_SYS_OMAP24_I2C_SLAVE
 #endif

 U_BOOT_I2C_ADAP_COMPLETE(omap24_3, omap24_i2c_init, omap24_i2c_probe,
 			 omap24_i2c_read, omap24_i2c_write, NULL,
 			 CONFIG_SYS_OMAP24_I2C_SPEED3,
 			 CONFIG_SYS_OMAP24_I2C_SLAVE3,
 			 3)
 #if (I2C_BUS_MAX > 4)
 #if !defined(CONFIG_SYS_OMAP24_I2C_SPEED4)
 #define CONFIG_SYS_OMAP24_I2C_SPEED4 CONFIG_SYS_OMAP24_I2C_SPEED
 #endif
 #if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE4)
 #define CONFIG_SYS_OMAP24_I2C_SLAVE4 CONFIG_SYS_OMAP24_I2C_SLAVE
 #endif

 U_BOOT_I2C_ADAP_COMPLETE(omap24_4, omap24_i2c_init, omap24_i2c_probe,
 			 omap24_i2c_read, omap24_i2c_write, NULL,
 			 CONFIG_SYS_OMAP24_I2C_SPEED4,
 			 CONFIG_SYS_OMAP24_I2C_SLAVE4,
 			 4)
 #endif
 #endif
 #endif
	/*
	* Basic I2C functions
	*
	* Copyright (c) 2004 Texas Instruments
	*
	* This package is free software; you can redistribute it and/or
	* modify it under the terms of the license found in the file
	* named COPYING that should have accompanied this file.
	*
	* THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
	* IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
	* WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
	*
	* Author: Jian Zhang jzhang@ti.com, Texas Instruments
	*
	* Copyright (c) 2003 Wolfgang Denk, wd@denx.de
	* Rewritten to fit into the current U-Boot framework
	*
	* Adapted for OMAP2420 I2C, r-woodruff2@ti.com
	*
	* Copyright (c) 2013 Lubomir Popov <lpopov@mm-sol.com>, MM Solutions
	* New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4
	* (4430/60/70), OMAP5 (5430) and AM335X (3359); should work on older
	* OMAPs and derivatives as well. The only anticipated exception would
	* be the OMAP2420, which shall require driver modification.
	* - Rewritten i2c_read to operate correctly with all types of chips
	* (old function could not read consistent data from some I2C slaves).
	* - Optimized i2c_write.
	* - New i2c_probe, performs write access vs read. The old probe could
	* hang the system under certain conditions (e.g. unconfigured pads).
	* - The read/write/probe functions try to identify unconfigured bus.
	* - Status functions now read irqstatus_raw as per TRM guidelines
	* (except for OMAP243X and OMAP34XX).
	* - Driver now supports up to I2C5 (OMAP5).
	*
	* Copyright (c) 2014 Hannes Petermaier <oe5hpm@oevsv.at>, B&R
	* - Added support for set_speed
	*
	*/

	#include <common.h>
	#include <i2c.h>

	#include <asm/arch/i2c.h>
	#include <asm/io.h>

	#include "omap24xx_i2c.h"

	DECLARE_GLOBAL_DATA_PTR;

	#define I2C_TIMEOUT 1000

	/* Absolutely safe for status update at 100 kHz I2C: */
	#define I2C_WAIT 200

	static int wait_for_bb(struct i2c_adapter *adap);
	static struct i2c omap24_get_base(struct i2c_adapter adap);
	static u16 wait_for_event(struct i2c_adapter *adap);
	static void flush_fifo(struct i2c_adapter *adap);
	static int omap24_i2c_findpsc(u32 pscl, u32 psch, uint speed)
	{
	unsigned int sampleclk, prescaler;
	int fsscll, fssclh;

	speed <<= 1;
	prescaler = 0;
	/*
	* some divisors may cause a precission loss, but shouldn't
	* be a big thing, because i2c_clk is then allready very slow.
	*/
	while (prescaler <= 0xFF) {
	sampleclk = I2C_IP_CLK / (prescaler+1);

	fsscll = sampleclk / speed;
	fssclh = fsscll;
	fsscll -= I2C_FASTSPEED_SCLL_TRIM;
	fssclh -= I2C_FASTSPEED_SCLH_TRIM;

	if (((fsscll > 0) && (fssclh > 0)) &&
	((fsscll <= (255-I2C_FASTSPEED_SCLL_TRIM)) &&
	(fssclh <= (255-I2C_FASTSPEED_SCLH_TRIM)))) {
	if (pscl)
	*pscl = fsscll;
	if (psch)
	*psch = fssclh;

	return prescaler;
	}
	prescaler++;
	}
	return -1;
	}
	static uint omap24_i2c_setspeed(struct i2c_adapter *adap, uint speed)
	{
	struct i2c *i2c_base = omap24_get_base(adap);
	int psc, fsscll = 0, fssclh = 0;
	int hsscll = 0, hssclh = 0;
	u32 scll = 0, sclh = 0;

	if (speed >= OMAP_I2C_HIGH_SPEED) {
	/* High speed */
	psc = I2C_IP_CLK / I2C_INTERNAL_SAMPLING_CLK;
	psc -= 1;
	if (psc < I2C_PSC_MIN) {
	printf("Error : I2C unsupported prescaler %d\n", psc);
	return -1;
	}

	/* For first phase of HS mode */
	fsscll = I2C_INTERNAL_SAMPLING_CLK / (2 * speed);

	fssclh = fsscll;

	fsscll -= I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM;
	fssclh -= I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM;
	if (((fsscll < 0) \|\| (fssclh < 0)) \|\|
	((fsscll > 255) \|\| (fssclh > 255))) {
	puts("Error : I2C initializing first phase clock\n");
	return -1;
	}

	/* For second phase of HS mode */
	hsscll = hssclh = I2C_INTERNAL_SAMPLING_CLK / (2 * speed);

	hsscll -= I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM;
	hssclh -= I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM;
	if (((fsscll < 0) \|\| (fssclh < 0)) \|\|
	((fsscll > 255) \|\| (fssclh > 255))) {
	puts("Error : I2C initializing second phase clock\n");
	return -1;
	}

	scll = (unsigned int)hsscll << 8 \| (unsigned int)fsscll;
	sclh = (unsigned int)hssclh << 8 \| (unsigned int)fssclh;

	} else {
	/* Standard and fast speed */
	psc = omap24_i2c_findpsc(&scll, &sclh, speed);
	if (0 > psc) {
	puts("Error : I2C initializing clock\n");
	return -1;
	}
	}

	adap->speed = speed;
	adap->waitdelay = (10000000 / speed) * 2; /* wait for 20 clkperiods */
	writew(0, &i2c_base->con);
	writew(psc, &i2c_base->psc);
	writew(scll, &i2c_base->scll);
	writew(sclh, &i2c_base->sclh);
	writew(I2C_CON_EN, &i2c_base->con);
	writew(0xFFFF, &i2c_base->stat); /* clear all pending status */

	return 0;
	}

	static void omap24_i2c_deblock(struct i2c_adapter *adap)
	{
	struct i2c *i2c_base = omap24_get_base(adap);
	int i;
	u16 systest;
	u16 orgsystest;

	/* set test mode ST_EN = 1 */
	orgsystest = readw(&i2c_base->systest);
	systest = orgsystest;
	/* enable testmode */
	systest \|= I2C_SYSTEST_ST_EN;
	writew(systest, &i2c_base->systest);
	systest &= ~I2C_SYSTEST_TMODE_MASK;
	systest \|= 3 << I2C_SYSTEST_TMODE_SHIFT;
	writew(systest, &i2c_base->systest);

	/* set SCL, SDA = 1 */
	systest \|= I2C_SYSTEST_SCL_O \| I2C_SYSTEST_SDA_O;
	writew(systest, &i2c_base->systest);
	udelay(10);

	/* toggle scl 9 clocks */
	for (i = 0; i < 9; i++) {
	/* SCL = 0 */
	systest &= ~I2C_SYSTEST_SCL_O;
	writew(systest, &i2c_base->systest);
	udelay(10);
	/* SCL = 1 */
	systest \|= I2C_SYSTEST_SCL_O;
	writew(systest, &i2c_base->systest);
	udelay(10);
	}

	/* send stop */
	systest &= ~I2C_SYSTEST_SDA_O;
	writew(systest, &i2c_base->systest);
	udelay(10);
	systest \|= I2C_SYSTEST_SCL_O \| I2C_SYSTEST_SDA_O;
	writew(systest, &i2c_base->systest);
	udelay(10);

	/* restore original mode */
	writew(orgsystest, &i2c_base->systest);
	}

	static void omap24_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd)
	{
	struct i2c *i2c_base = omap24_get_base(adap);
	int timeout = I2C_TIMEOUT;
	int deblock = 1;

	retry:
	if (readw(&i2c_base->con) & I2C_CON_EN) {
	writew(0, &i2c_base->con);
	udelay(50000);
	}

	writew(0x2, &i2c_base->sysc); /* for ES2 after soft reset */
	udelay(1000);

	writew(I2C_CON_EN, &i2c_base->con);
	while (!(readw(&i2c_base->syss) & I2C_SYSS_RDONE) && timeout--) {
	if (timeout <= 0) {
	puts("ERROR: Timeout in soft-reset\n");
	return;
	}
	udelay(1000);
	}

	if (0 != omap24_i2c_setspeed(adap, speed)) {
	printf("ERROR: failed to setup I2C bus-speed!\n");
	return;
	}

	/* own address */
	writew(slaveadd, &i2c_base->oa);

	#if defined(CONFIG_OMAP243X) \|\| defined(CONFIG_OMAP34XX)
	/*
	* Have to enable interrupts for OMAP2/3, these IPs don't have
	* an 'irqstatus_raw' register and we shall have to poll 'stat'
	*/
	writew(I2C_IE_XRDY_IE \| I2C_IE_RRDY_IE \| I2C_IE_ARDY_IE \|
	I2C_IE_NACK_IE \| I2C_IE_AL_IE, &i2c_base->ie);
	#endif
	udelay(1000);
	flush_fifo(adap);
	writew(0xFFFF, &i2c_base->stat);

	/* Handle possible failed I2C state */
	if (wait_for_bb(adap))
	if (deblock == 1) {
	omap24_i2c_deblock(adap);
	deblock = 0;
	goto retry;
	}
	}

	static void flush_fifo(struct i2c_adapter *adap)
	{
	struct i2c *i2c_base = omap24_get_base(adap);
	u16 stat;

	/*
	* note: if you try and read data when its not there or ready
	* you get a bus error
	*/
	while (1) {
	stat = readw(&i2c_base->stat);
	if (stat == I2C_STAT_RRDY) {
	readb(&i2c_base->data);
	writew(I2C_STAT_RRDY, &i2c_base->stat);
	udelay(1000);
	} else
	break;
	}
	}

	/*
	* i2c_probe: Use write access. Allows to identify addresses that are
	* write-only (like the config register of dual-port EEPROMs)
	*/
	static int omap24_i2c_probe(struct i2c_adapter *adap, uchar chip)
	{
	struct i2c *i2c_base = omap24_get_base(adap);
	u16 status;
	int res = 1; /* default = fail */

	if (chip == readw(&i2c_base->oa))
	return res;

	/* Wait until bus is free */
	if (wait_for_bb(adap))
	return res;

	/* No data transfer, slave addr only */
	writew(chip, &i2c_base->sa);
	/* Stop bit needed here */
	writew(I2C_CON_EN \| I2C_CON_MST \| I2C_CON_STT \| I2C_CON_TRX \|
	I2C_CON_STP, &i2c_base->con);

	status = wait_for_event(adap);

	if ((status & ~I2C_STAT_XRDY) == 0 \|\| (status & I2C_STAT_AL)) {
	/*
	* With current high-level command implementation, notifying
	* the user shall flood the console with 127 messages. If
	* silent exit is desired upon unconfigured bus, remove the
	* following 'if' section:
	*/
	if (status == I2C_STAT_XRDY)
	printf("i2c_probe: pads on bus %d probably not configured (status=0x%x)\n",
	adap->hwadapnr, status);

	goto pr_exit;
	}

	/* Check for ACK (!NAK) */
	if (!(status & I2C_STAT_NACK)) {
	res = 0; /* Device found */
	udelay(adap->waitdelay);/* Required by AM335X in SPL */
	/* Abort transfer (force idle state) */
	writew(I2C_CON_MST \| I2C_CON_TRX, &i2c_base->con); /* Reset */
	udelay(1000);
	writew(I2C_CON_EN \| I2C_CON_MST \| I2C_CON_TRX \|
	I2C_CON_STP, &i2c_base->con); /* STP */
	}
	pr_exit:
	flush_fifo(adap);
	writew(0xFFFF, &i2c_base->stat);
	return res;
	}

	/*
	* i2c_read: Function now uses a single I2C read transaction with bulk transfer
	* of the requested number of bytes (note that the 'i2c md' command
	* limits this to 16 bytes anyway). If CONFIG_I2C_REPEATED_START is
	* defined in the board config header, this transaction shall be with
	* Repeated Start (Sr) between the address and data phases; otherwise
	* Stop-Start (P-S) shall be used (some I2C chips do require a P-S).
	* The address (reg offset) may be 0, 1 or 2 bytes long.
	* Function now reads correctly from chips that return more than one
	* byte of data per addressed register (like TI temperature sensors),
	* or that do not need a register address at all (such as some clock
	* distributors).
	*/
	static int omap24_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
	int alen, uchar *buffer, int len)
	{
	struct i2c *i2c_base = omap24_get_base(adap);
	int i2c_error = 0;
	u16 status;

	if (alen < 0) {
	puts("I2C read: addr len < 0\n");
	return 1;
	}
	if (len < 0) {
	puts("I2C read: data len < 0\n");
	return 1;
	}
	if (buffer == NULL) {
	puts("I2C read: NULL pointer passed\n");
	return 1;
	}

	if (alen > 2) {
	printf("I2C read: addr len %d not supported\n", alen);
	return 1;
	}

	if (addr + len > (1 << 16)) {
	puts("I2C read: address out of range\n");
	return 1;
	}

	/* Wait until bus not busy */
	if (wait_for_bb(adap))
	return 1;

	/* Zero, one or two bytes reg address (offset) */
	writew(alen, &i2c_base->cnt);
	/* Set slave address */
	writew(chip, &i2c_base->sa);

	if (alen) {
	/* Must write reg offset first */
	#ifdef CONFIG_I2C_REPEATED_START
	/* No stop bit, use Repeated Start (Sr) */
	writew(I2C_CON_EN \| I2C_CON_MST \| I2C_CON_STT \|
	I2C_CON_TRX, &i2c_base->con);
	#else
	/* Stop - Start (P-S) */
	writew(I2C_CON_EN \| I2C_CON_MST \| I2C_CON_STT \| I2C_CON_STP \|
	I2C_CON_TRX, &i2c_base->con);
	#endif
	/* Send register offset */
	while (1) {
	status = wait_for_event(adap);
	/* Try to identify bus that is not padconf'd for I2C */
	if (status == I2C_STAT_XRDY) {
	i2c_error = 2;
	printf("i2c_read (addr phase): pads on bus %d probably not configured (status=0x%x)\n",
	adap->hwadapnr, status);
	goto rd_exit;
	}
	if (status == 0 \|\| (status & I2C_STAT_NACK)) {
	i2c_error = 1;
	printf("i2c_read: error waiting for addr ACK (status=0x%x)\n",
	status);
	goto rd_exit;
	}
	if (alen) {
	if (status & I2C_STAT_XRDY) {
	alen--;
	/* Do we have to use byte access? */
	writeb((addr >> (8 * alen)) & 0xff,
	&i2c_base->data);
	writew(I2C_STAT_XRDY, &i2c_base->stat);
	}
	}
	if (status & I2C_STAT_ARDY) {
	writew(I2C_STAT_ARDY, &i2c_base->stat);
	break;
	}
	}
	}
	/* Set slave address */
	writew(chip, &i2c_base->sa);
	/* Read len bytes from slave */
	writew(len, &i2c_base->cnt);
	/* Need stop bit here */
	writew(I2C_CON_EN \| I2C_CON_MST \|
	I2C_CON_STT \| I2C_CON_STP,
	&i2c_base->con);

	/* Receive data */
	while (1) {
	status = wait_for_event(adap);
	/*
	* Try to identify bus that is not padconf'd for I2C. This
	* state could be left over from previous transactions if
	* the address phase is skipped due to alen=0.
	*/
	if (status == I2C_STAT_XRDY) {
	i2c_error = 2;
	printf("i2c_read (data phase): pads on bus %d probably not configured (status=0x%x)\n",
	adap->hwadapnr, status);
	goto rd_exit;
	}
	if (status == 0 \|\| (status & I2C_STAT_NACK)) {
	i2c_error = 1;
	goto rd_exit;
	}
	if (status & I2C_STAT_RRDY) {
	*buffer++ = readb(&i2c_base->data);
	writew(I2C_STAT_RRDY, &i2c_base->stat);
	}
	if (status & I2C_STAT_ARDY) {
	writew(I2C_STAT_ARDY, &i2c_base->stat);
	break;
	}
	}

	rd_exit:
	flush_fifo(adap);
	writew(0xFFFF, &i2c_base->stat);
	return i2c_error;
	}

	/* i2c_write: Address (reg offset) may be 0, 1 or 2 bytes long. */
	static int omap24_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
	int alen, uchar *buffer, int len)
	{
	struct i2c *i2c_base = omap24_get_base(adap);
	int i;
	u16 status;
	int i2c_error = 0;
	int timeout = I2C_TIMEOUT;

	if (alen < 0) {
	puts("I2C write: addr len < 0\n");
	return 1;
	}

	if (len < 0) {
	puts("I2C write: data len < 0\n");
	return 1;
	}

	if (buffer == NULL) {
	puts("I2C write: NULL pointer passed\n");
	return 1;
	}

	if (alen > 2) {
	printf("I2C write: addr len %d not supported\n", alen);
	return 1;
	}

	if (addr + len > (1 << 16)) {
	printf("I2C write: address 0x%x + 0x%x out of range\n",
	addr, len);
	return 1;
	}

	/* Wait until bus not busy */
	if (wait_for_bb(adap))
	return 1;

	/* Start address phase - will write regoffset + len bytes data */
	writew(alen + len, &i2c_base->cnt);
	/* Set slave address */
	writew(chip, &i2c_base->sa);
	/* Stop bit needed here */
	writew(I2C_CON_EN \| I2C_CON_MST \| I2C_CON_STT \| I2C_CON_TRX \|
	I2C_CON_STP, &i2c_base->con);

	while (alen) {
	/* Must write reg offset (one or two bytes) */
	status = wait_for_event(adap);
	/* Try to identify bus that is not padconf'd for I2C */
	if (status == I2C_STAT_XRDY) {
	i2c_error = 2;
	printf("i2c_write: pads on bus %d probably not configured (status=0x%x)\n",
	adap->hwadapnr, status);
	goto wr_exit;
	}
	if (status == 0 \|\| (status & I2C_STAT_NACK)) {
	i2c_error = 1;
	printf("i2c_write: error waiting for addr ACK (status=0x%x)\n",
	status);
	goto wr_exit;
	}
	if (status & I2C_STAT_XRDY) {
	alen--;
	writeb((addr >> (8 * alen)) & 0xff, &i2c_base->data);
	writew(I2C_STAT_XRDY, &i2c_base->stat);
	} else {
	i2c_error = 1;
	printf("i2c_write: bus not ready for addr Tx (status=0x%x)\n",
	status);
	goto wr_exit;
	}
	}
	/* Address phase is over, now write data */
	for (i = 0; i < len; i++) {
	status = wait_for_event(adap);
	if (status == 0 \|\| (status & I2C_STAT_NACK)) {
	i2c_error = 1;
	printf("i2c_write: error waiting for data ACK (status=0x%x)\n",
	status);
	goto wr_exit;
	}
	if (status & I2C_STAT_XRDY) {
	writeb(buffer[i], &i2c_base->data);
	writew(I2C_STAT_XRDY, &i2c_base->stat);
	} else {
	i2c_error = 1;
	printf("i2c_write: bus not ready for data Tx (i=%d)\n",
	i);
	goto wr_exit;
	}
	}
	/*
	* poll ARDY bit for making sure that last byte really has been
	* transferred on the bus.
	*/
	do {
	status = wait_for_event(adap);
	} while (!(status & I2C_STAT_ARDY) && timeout--);
	if (timeout <= 0)
	printf("i2c_write: timed out writig last byte!\n");

	wr_exit:
	flush_fifo(adap);
	writew(0xFFFF, &i2c_base->stat);
	return i2c_error;
	}

	/*
	* Wait for the bus to be free by checking the Bus Busy (BB)
	* bit to become clear
	*/
	static int wait_for_bb(struct i2c_adapter *adap)
	{
	struct i2c *i2c_base = omap24_get_base(adap);
	int timeout = I2C_TIMEOUT;
	u16 stat;

	writew(0xFFFF, &i2c_base->stat); /* clear current interrupts...*/
	#if defined(CONFIG_OMAP243X) \|\| defined(CONFIG_OMAP34XX)
	while ((stat = readw(&i2c_base->stat) & I2C_STAT_BB) && timeout--) {
	#else
	/* Read RAW status */
	while ((stat = readw(&i2c_base->irqstatus_raw) &
	I2C_STAT_BB) && timeout--) {
	#endif
	writew(stat, &i2c_base->stat);
	udelay(adap->waitdelay);
	}

	if (timeout <= 0) {
	printf("Timed out in wait_for_bb: status=%04x\n",
	stat);
	return 1;
	}
	writew(0xFFFF, &i2c_base->stat); /* clear delayed stuff*/
	return 0;
	}

	/*
	* Wait for the I2C controller to complete current action
	* and update status
	*/
	static u16 wait_for_event(struct i2c_adapter *adap)
	{
	struct i2c *i2c_base = omap24_get_base(adap);
	u16 status;
	int timeout = I2C_TIMEOUT;

	do {
	udelay(adap->waitdelay);
	#if defined(CONFIG_OMAP243X) \|\| defined(CONFIG_OMAP34XX)
	status = readw(&i2c_base->stat);
	#else
	/* Read RAW status */
	status = readw(&i2c_base->irqstatus_raw);
	#endif
	} while (!(status &
	(I2C_STAT_ROVR \| I2C_STAT_XUDF \| I2C_STAT_XRDY \|
	I2C_STAT_RRDY \| I2C_STAT_ARDY \| I2C_STAT_NACK \|
	I2C_STAT_AL)) && timeout--);

	if (timeout <= 0) {
	printf("Timed out in wait_for_event: status=%04x\n",
	status);
	/*
	* If status is still 0 here, probably the bus pads have
	* not been configured for I2C, and/or pull-ups are missing.
	*/
	printf("Check if pads/pull-ups of bus %d are properly configured\n",
	adap->hwadapnr);
	writew(0xFFFF, &i2c_base->stat);
	status = 0;
	}

	return status;
	}

	static struct i2c omap24_get_base(struct i2c_adapter adap)
	{
	switch (adap->hwadapnr) {
	case 0:
	return (struct i2c *)I2C_BASE1;
	break;
	case 1:
	return (struct i2c *)I2C_BASE2;
	break;
	#if (I2C_BUS_MAX > 2)
	case 2:
	return (struct i2c *)I2C_BASE3;
	break;
	#if (I2C_BUS_MAX > 3)
	case 3:
	return (struct i2c *)I2C_BASE4;
	break;
	#if (I2C_BUS_MAX > 4)
	case 4:
	return (struct i2c *)I2C_BASE5;
	break;
	#endif
	#endif
	#endif
	default:
	printf("wrong hwadapnr: %d\n", adap->hwadapnr);
	break;
	}
	return NULL;
	}

	#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED1)
	#define CONFIG_SYS_OMAP24_I2C_SPEED1 CONFIG_SYS_OMAP24_I2C_SPEED
	#endif
	#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE1)
	#define CONFIG_SYS_OMAP24_I2C_SLAVE1 CONFIG_SYS_OMAP24_I2C_SLAVE
	#endif

	U_BOOT_I2C_ADAP_COMPLETE(omap24_0, omap24_i2c_init, omap24_i2c_probe,
	omap24_i2c_read, omap24_i2c_write, omap24_i2c_setspeed,
	CONFIG_SYS_OMAP24_I2C_SPEED,
	CONFIG_SYS_OMAP24_I2C_SLAVE,
	0)
	U_BOOT_I2C_ADAP_COMPLETE(omap24_1, omap24_i2c_init, omap24_i2c_probe,
	omap24_i2c_read, omap24_i2c_write, omap24_i2c_setspeed,
	CONFIG_SYS_OMAP24_I2C_SPEED1,
	CONFIG_SYS_OMAP24_I2C_SLAVE1,
	1)
	#if (I2C_BUS_MAX > 2)
	#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED2)
	#define CONFIG_SYS_OMAP24_I2C_SPEED2 CONFIG_SYS_OMAP24_I2C_SPEED
	#endif
	#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE2)
	#define CONFIG_SYS_OMAP24_I2C_SLAVE2 CONFIG_SYS_OMAP24_I2C_SLAVE
	#endif

	U_BOOT_I2C_ADAP_COMPLETE(omap24_2, omap24_i2c_init, omap24_i2c_probe,
	omap24_i2c_read, omap24_i2c_write, NULL,
	CONFIG_SYS_OMAP24_I2C_SPEED2,
	CONFIG_SYS_OMAP24_I2C_SLAVE2,
	2)
	#if (I2C_BUS_MAX > 3)
	#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED3)
	#define CONFIG_SYS_OMAP24_I2C_SPEED3 CONFIG_SYS_OMAP24_I2C_SPEED
	#endif
	#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE3)
	#define CONFIG_SYS_OMAP24_I2C_SLAVE3 CONFIG_SYS_OMAP24_I2C_SLAVE
	#endif

	U_BOOT_I2C_ADAP_COMPLETE(omap24_3, omap24_i2c_init, omap24_i2c_probe,
	omap24_i2c_read, omap24_i2c_write, NULL,
	CONFIG_SYS_OMAP24_I2C_SPEED3,
	CONFIG_SYS_OMAP24_I2C_SLAVE3,
	3)
	#if (I2C_BUS_MAX > 4)
	#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED4)
	#define CONFIG_SYS_OMAP24_I2C_SPEED4 CONFIG_SYS_OMAP24_I2C_SPEED
	#endif
	#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE4)
	#define CONFIG_SYS_OMAP24_I2C_SLAVE4 CONFIG_SYS_OMAP24_I2C_SLAVE
	#endif

	U_BOOT_I2C_ADAP_COMPLETE(omap24_4, omap24_i2c_init, omap24_i2c_probe,
	omap24_i2c_read, omap24_i2c_write, NULL,
	CONFIG_SYS_OMAP24_I2C_SPEED4,
	CONFIG_SYS_OMAP24_I2C_SLAVE4,
	4)
	#endif
	#endif
	#endif