Add support for INKA4X0 board
diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h
new file mode 100644
index 0000000..c7dbfd0
--- /dev/null
+++ b/include/configs/inka4x0.h
@@ -0,0 +1,244 @@
+/*
+ * (C) Copyright 2003-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
+#define CONFIG_INKA4X0 1 /* INKA4x0 board */
+
+#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * Supported commands
+ */
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#if (TEXT_BASE == 0xFFE00000) /* Boot low */
+# define CFG_LOWBOOT 1
+#endif
+
+/*
+ * Autobooting
+ */
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath)\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname):$(netdev):off panic=1\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm $(kernel_addr)\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm $(kernel_addr) $(ramdisk_addr)\0" \
+ "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "rootpath=/opt/eldk3.0_ppc/ppc_82xx\0" \
+ "bootfile=uImage\0" \
+ "serverip=192.168.1.1\0" \
+ "ipaddr=192.168.160.2\0" \
+ "ethaddr=00:00:1A:1B:CE:AF\0" \
+ "dk=tftp 100000 inka4x0/u-boot.dk;protect off all;erase ffe00000 ffe2ffff;cp.b 100000 ffe00000 $(filesize)\0" \
+ ""
+
+#define CONFIG_BOOTCOMMAND "run net_nfs"
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+
+/*
+ * Flash configuration
+ */
+#define CFG_FLASH_BASE 0xFFE00000
+
+#define CFG_FLASH_SIZE 0x00200000 /* 2 MByte */
+#define CFG_MAX_FLASH_SECT 35 /* max num of sects on one chip */
+
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000) /* second sector */
+#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
+ (= chip selects) */
+#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+/*
+ * Environment settings
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SIZE 0x2000
+#define CFG_ENV_SECT_SIZE 0x2000
+#define CONFIG_ENV_OVERWRITE 1
+
+/*
+ * Memory map
+ */
+#define CFG_MBAR 0xF0000000
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_DEFAULT_MBAR 0x80000000
+
+#define CONFIG_MPC5200_DDR
+
+/* Use ON-Chip SRAM until RAM will be available */
+#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
+#else
+#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE
+#endif
+
+
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_BASE TEXT_BASE
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+# define CFG_RAMBOOT 1
+#endif
+
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC 1
+/*
+ * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ */
+/* #define CONFIG_FEC_10MBIT 1 */
+#define CONFIG_PHY_ADDR 0x00
+
+/*
+ * GPIO configuration
+ *
+ * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
+ * Bit 0 (mask: 0x80000000): 1
+ * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
+ * 00 -> No Alternatives, I2C1 is used for onboard EEPROM
+ * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard
+ * EEPROM
+ * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
+ * use PSC6_1 and PSC6_3 as GPIO: Bits 9:11 (mask: 0x07000000):
+ * 011 -> PSC6 could not be used as UART or CODEC. IrDA still possible.
+ * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
+ * tests.
+ */
+#if defined (CONFIG_MINIFAP)
+#define CFG_GPS_PORT_CONFIG 0x93000004
+#else
+#define CFG_GPS_PORT_CONFIG 0x83000004
+#endif
+
+/*
+ * RTC configuration
+ */
+#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+/* Enable an alternate, more extensive memory test */
+#define CFG_ALT_MEMTEST
+
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+/*
+ * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
+ * which is normally part of the default commands (CFV_CMD_DFL)
+ */
+#define CONFIG_LOOPW
+
+/*
+ * Various low-level settings
+ */
+#if defined(CONFIG_MPC5200)
+#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
+#define CFG_HID0_FINAL HID0_ICE
+#else
+#define CFG_HID0_INIT 0
+#define CFG_HID0_FINAL 0
+#endif
+
+#define CFG_BOOTCS_START CFG_FLASH_BASE
+#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
+#define CFG_BOOTCS_CFG 0x00087800 /* for pci_clk = 66 MHz */
+#define CFG_CS0_START CFG_FLASH_BASE
+#define CFG_CS0_SIZE CFG_FLASH_SIZE
+
+#define CFG_CS_BURST 0x00000000
+#define CFG_CS_DEADCYCLE 0x33333333
+
+#endif /* __CONFIG_H */
diff --git a/include/flash.h b/include/flash.h
index a93c9b2..20ef2c3 100644
--- a/include/flash.h
+++ b/include/flash.h
@@ -149,6 +149,7 @@
#define AMD_ID_F016D 0xAD /* 29F016 ID ( 2 M x 8) */
#define AMD_ID_F032B 0x41 /* 29F032 ID ( 4 M x 8) */
#define AMD_ID_LV116DT 0xC7 /* 29LV116DT ( 2 M x 8, top boot sect) */
+#define AMD_ID_LV116DB 0x4C /* 29LV116DB ( 2 M x 8, bottom boot sect) */
#define AMD_ID_LV016B 0xc8 /* 29LV016 ID ( 2 M x 8) */
#define AMD_ID_PL160CB 0x22452245 /* 29PL160CB ID (16 M, bottom boot sect */
@@ -284,6 +285,7 @@
#define FLASH_AM800T 0x0004 /* AMD AM29LV800 */
#define FLASH_AM800B 0x0005
#define FLASH_AM116DT 0x0026 /* AMD AM29LV116DT (2Mx8bit) */
+#define FLASH_AM116DB 0x0027 /* AMD AM29LV116DB (2Mx8bit) */
#define FLASH_AM160T 0x0006 /* AMD AM29LV160 */
#define FLASH_AM160LV 0x0046 /* AMD29LV160DB (2M = 2Mx8bit ) */
#define FLASH_AM160B 0x0007
