* Code cleanup (ARM mostly)
* Patch by Curt Brune, 17 May 2004:
- Add support for Samsung S3C4510B CPU (ARM7tdmi based SoC)
- Add support for ESPD-Inc. EVB4510 Board
diff --git a/cpu/arm720t/start.S b/cpu/arm720t/start.S
index f6ae9d6..15b9a05 100644
--- a/cpu/arm720t/start.S
+++ b/cpu/arm720t/start.S
@@ -26,9 +26,7 @@
#include <config.h>
#include <version.h>
-#ifdef CONFIG_NETARM
-#include <asm/arch/netarm_registers.h>
-#endif
+#include <asm/hardware.h>
/*
*************************************************************************
@@ -166,7 +164,6 @@
_start_armboot: .word start_armboot
-
/*
*************************************************************************
*
@@ -178,6 +175,7 @@
*************************************************************************
*/
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312)
/* Interupt-Controller base addresses */
INTMR1: .word 0x80000280 @ 32 bit size
@@ -195,8 +193,11 @@
#define CLKCTL_49 0x4 /* 49.152 MHz */
#define CLKCTL_73 0x6 /* 73.728 MHz */
+#endif
+
cpu_init_crit:
-#ifndef CONFIG_NETARM
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312)
+
/*
* mask all IRQs by clearing all bits in the INTMRs
*/
@@ -223,7 +224,7 @@
bic r0, r0, #0x0000008f @ clear bits 7, 3:0 (B--- WCAM)
orr r0, r0, #0x00000002 @ set bit 2 (A) Align
mcr p15,0,r0,c1,c0
-#else /* CONFIG_NETARM */
+#elif defined(CONFIG_NETARM)
/*
* prior to software reset : need to set pin PORTC4 to be *HRESET
*/
@@ -270,7 +271,26 @@
mov r1, #0
ldr r0, =NETARM_GEN_MODULE_BASE
str r1, [r0, #+NETARM_GEN_INTR_ENABLE]
-#endif /* CONFIG_NETARM */
+
+#elif defined(CONFIG_S3C4510B)
+
+ /*
+ * Mask off all IRQ sources
+ */
+ ldr r1, =REG_INTMASK
+ ldr r0, =0x3FFFFF
+ str r0, [r1]
+
+ /*
+ * Disable Cache
+ */
+ ldr r0, =REG_SYSCFG
+ ldr r1, =0x83ffffa0 /* cache-disabled */
+ str r1, [r0]
+
+#else
+#error No cpu_init_crit() defined for current CPU type
+#endif
#ifdef CONFIG_ARM7_REVD
/* set clock speed */
@@ -462,10 +482,10 @@
#endif
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312)
.align 5
.globl reset_cpu
reset_cpu:
-#ifndef CONFIG_NETARM
mov ip, #0
mcr p15, 0, ip, c7, c7, 0 @ invalidate cache
mcr p15, 0, ip, c8, c7, 0 @ flush TLB (v4)
@@ -474,7 +494,10 @@
bic ip, ip, #0x2100 @ ..v....s........
mcr p15, 0, ip, c1, c0, 0 @ ctrl register
mov pc, r0
-#else
+#elif defined(CONFIG_NETARM)
+ .align 5
+.globl reset_cpu
+reset_cpu:
ldr r1, =NETARM_MEM_MODULE_BASE
ldr r0, [r1, #+NETARM_MEM_CS0_BASE_ADDR]
ldr r1, =0xFFFFF000
@@ -491,4 +514,9 @@
ldr r1, =NETARM_GEN_SW_SVC_RESETB
str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
mov pc, r0
+#elif defined(CONFIG_S3C4510B)
+/* Nothing done here as reseting the CPU is board specific, depending
+ * on external peripherals such as watchdog timers, etc. */
+#else
+#error No reset_cpu() defined for current CPU type
#endif
