Merge git://www.denx.de/git/u-boot
Conflicts:
include/asm-microblaze/microblaze_intc.h
include/linux/stat.h
diff --git a/include/linux/mii.h b/include/linux/mii.h
new file mode 100644
index 0000000..7c63095
--- /dev/null
+++ b/include/linux/mii.h
@@ -0,0 +1,158 @@
+/*
+ * linux/mii.h: definitions for MII-compatible transceivers
+ * Originally drivers/net/sunhme.h.
+ *
+ * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
+ */
+
+#ifndef __LINUX_MII_H__
+#define __LINUX_MII_H__
+
+/* Generic MII registers. */
+
+#define MII_BMCR 0x00 /* Basic mode control register */
+#define MII_BMSR 0x01 /* Basic mode status register */
+#define MII_PHYSID1 0x02 /* PHYS ID 1 */
+#define MII_PHYSID2 0x03 /* PHYS ID 2 */
+#define MII_ADVERTISE 0x04 /* Advertisement control reg */
+#define MII_LPA 0x05 /* Link partner ability reg */
+#define MII_EXPANSION 0x06 /* Expansion register */
+#define MII_DCOUNTER 0x12 /* Disconnect counter */
+#define MII_FCSCOUNTER 0x13 /* False carrier counter */
+#define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */
+#define MII_RERRCOUNTER 0x15 /* Receive error counter */
+#define MII_SREVISION 0x16 /* Silicon revision */
+#define MII_RESV1 0x17 /* Reserved... */
+#define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */
+#define MII_PHYADDR 0x19 /* PHY address */
+#define MII_RESV2 0x1a /* Reserved... */
+#define MII_TPISTATUS 0x1b /* TPI status for 10mbps */
+#define MII_NCONFIG 0x1c /* Network interface config */
+
+/* Basic mode control register. */
+#define BMCR_RESV 0x003f /* Unused... */
+#define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */
+#define BMCR_CTST 0x0080 /* Collision test */
+#define BMCR_FULLDPLX 0x0100 /* Full duplex */
+#define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */
+#define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */
+#define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */
+#define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */
+#define BMCR_SPEED100 0x2000 /* Select 100Mbps */
+#define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */
+#define BMCR_RESET 0x8000 /* Reset the DP83840 */
+
+/* Basic mode status register. */
+#define BMSR_ERCAP 0x0001 /* Ext-reg capability */
+#define BMSR_JCD 0x0002 /* Jabber detected */
+#define BMSR_LSTATUS 0x0004 /* Link status */
+#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */
+#define BMSR_RFAULT 0x0010 /* Remote fault detected */
+#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */
+#define BMSR_RESV 0x07c0 /* Unused... */
+#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */
+#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */
+#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */
+#define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */
+#define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */
+
+/* Advertisement control register. */
+#define ADVERTISE_SLCT 0x001f /* Selector bits */
+#define ADVERTISE_CSMA 0x0001 /* Only selector supported */
+#define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */
+#define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */
+#define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */
+#define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */
+#define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */
+#define ADVERTISE_RESV 0x1c00 /* Unused... */
+#define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */
+#define ADVERTISE_LPACK 0x4000 /* Ack link partners response */
+#define ADVERTISE_NPAGE 0x8000 /* Next page bit */
+
+#define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \
+ ADVERTISE_CSMA)
+#define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
+ ADVERTISE_100HALF | ADVERTISE_100FULL)
+
+/* Link partner ability register. */
+#define LPA_SLCT 0x001f /* Same as advertise selector */
+#define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */
+#define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */
+#define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */
+#define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */
+#define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */
+#define LPA_RESV 0x1c00 /* Unused... */
+#define LPA_RFAULT 0x2000 /* Link partner faulted */
+#define LPA_LPACK 0x4000 /* Link partner acked us */
+#define LPA_NPAGE 0x8000 /* Next page bit */
+
+#define LPA_DUPLEX (LPA_10FULL | LPA_100FULL)
+#define LPA_100 (LPA_100FULL | LPA_100HALF | LPA_100BASE4)
+
+/* Expansion register for auto-negotiation. */
+#define EXPANSION_NWAY 0x0001 /* Can do N-way auto-nego */
+#define EXPANSION_LCWP 0x0002 /* Got new RX page code word */
+#define EXPANSION_ENABLENPAGE 0x0004 /* This enables npage words */
+#define EXPANSION_NPCAPABLE 0x0008 /* Link partner supports npage */
+#define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */
+#define EXPANSION_RESV 0xffe0 /* Unused... */
+
+/* N-way test register. */
+#define NWAYTEST_RESV1 0x00ff /* Unused... */
+#define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */
+#define NWAYTEST_RESV2 0xfe00 /* Unused... */
+
+
+/**
+ * mii_nway_result
+ * @negotiated: value of MII ANAR and'd with ANLPAR
+ *
+ * Given a set of MII abilities, check each bit and returns the
+ * currently supported media, in the priority order defined by
+ * IEEE 802.3u. We use LPA_xxx constants but note this is not the
+ * value of LPA solely, as described above.
+ *
+ * The one exception to IEEE 802.3u is that 100baseT4 is placed
+ * between 100T-full and 100T-half. If your phy does not support
+ * 100T4 this is fine. If your phy places 100T4 elsewhere in the
+ * priority order, you will need to roll your own function.
+ */
+static inline unsigned int mii_nway_result (unsigned int negotiated)
+{
+ unsigned int ret;
+
+ if (negotiated & LPA_100FULL)
+ ret = LPA_100FULL;
+ else if (negotiated & LPA_100BASE4)
+ ret = LPA_100BASE4;
+ else if (negotiated & LPA_100HALF)
+ ret = LPA_100HALF;
+ else if (negotiated & LPA_10FULL)
+ ret = LPA_10FULL;
+ else
+ ret = LPA_10HALF;
+
+ return ret;
+}
+
+/**
+ * mii_duplex
+ * @duplex_lock: Non-zero if duplex is locked at full
+ * @negotiated: value of MII ANAR and'd with ANLPAR
+ *
+ * A small helper function for a common case. Returns one
+ * if the media is operating or locked at full duplex, and
+ * returns zero otherwise.
+ */
+static inline unsigned int mii_duplex (unsigned int duplex_lock,
+ unsigned int negotiated)
+{
+ if (duplex_lock)
+ return 1;
+ if (mii_nway_result(negotiated) & LPA_DUPLEX)
+ return 1;
+ return 0;
+}
+
+
+#endif /* __LINUX_MII_H__ */
diff --git a/include/linux/stat.h b/include/linux/stat.h
index 39386f1..37f2924 100644
--- a/include/linux/stat.h
+++ b/include/linux/stat.h
@@ -7,7 +7,7 @@
extern "C" {
#endif
-#define S_IFMT 00170000 /* type of file */
+#define S_IFMT 00170000 /* type of file */
#define S_IFSOCK 0140000 /* named socket */
#define S_IFLNK 0120000 /* symbolic link */
#define S_IFREG 0100000 /* regular */
@@ -49,25 +49,25 @@
ino_t st_ino; /* file id */
mode_t st_mode; /* ownership/protection */
nlink_t st_nlink; /* number of links */
- uid_t st_uid; /* user id */
- gid_t st_gid; /* group id */
+ uid_t st_uid; /* user id */
+ gid_t st_gid; /* group id */
dev_t st_rdev;
off_t st_size; /* file size in # of bytes */
- unsigned long st_blksize; /* block size */
- unsigned long st_blocks; /* file size in # of blocks */
- unsigned long st_atime; /* time file was last accessed */
- unsigned long __unused1;
- unsigned long st_mtime; /* time file was last modified */
- unsigned long __unused2;
- unsigned long st_ctime; /* time file status was last changed */
- unsigned long __unused3;
- unsigned long __unused4;
- unsigned long __unused5;
+ unsigned long st_blksize; /* block size */
+ unsigned long st_blocks; /* file size in # of blocks */
+ unsigned long st_atime; /* time file was last accessed */
+ unsigned long __unused1;
+ unsigned long st_mtime; /* time file was last modified */
+ unsigned long __unused2;
+ unsigned long st_ctime; /* time file status was last changed */
+ unsigned long __unused3;
+ unsigned long __unused4;
+ unsigned long __unused5;
};
#endif /* __PPC__ */
-#if defined (__ARM__) || defined (__I386__) || defined (__M68K__) || defined (__blackfin__) ||\
+#if defined (__ARM__) || defined (__I386__) || defined (__M68K__) || defined (__bfin__) ||\
defined (__microblaze__)
struct stat {
@@ -98,34 +98,59 @@
#if defined (__MIPS__)
struct stat {
- dev_t st_dev;
- long st_pad1[3];
- ino_t st_ino;
- mode_t st_mode;
- nlink_t st_nlink;
- uid_t st_uid;
- gid_t st_gid;
- dev_t st_rdev;
- long st_pad2[2];
- off_t st_size;
- long st_pad3;
+ dev_t st_dev;
+ long st_pad1[3];
+ ino_t st_ino;
+ mode_t st_mode;
+ nlink_t st_nlink;
+ uid_t st_uid;
+ gid_t st_gid;
+ dev_t st_rdev;
+ long st_pad2[2];
+ off_t st_size;
+ long st_pad3;
/*
* Actually this should be timestruc_t st_atime, st_mtime and st_ctime
* but we don't have it under Linux.
*/
- time_t st_atime;
- long reserved0;
- time_t st_mtime;
- long reserved1;
- time_t st_ctime;
- long reserved2;
- long st_blksize;
- long st_blocks;
- long st_pad4[14];
+ time_t st_atime;
+ long reserved0;
+ time_t st_mtime;
+ long reserved1;
+ time_t st_ctime;
+ long reserved2;
+ long st_blksize;
+ long st_blocks;
+ long st_pad4[14];
};
#endif /* __MIPS__ */
+#if defined(__AVR32__)
+
+struct stat {
+ unsigned long st_dev;
+ unsigned long st_ino;
+ unsigned short st_mode;
+ unsigned short st_nlink;
+ unsigned short st_uid;
+ unsigned short st_gid;
+ unsigned long st_rdev;
+ unsigned long st_size;
+ unsigned long st_blksize;
+ unsigned long st_blocks;
+ unsigned long st_atime;
+ unsigned long st_atime_nsec;
+ unsigned long st_mtime;
+ unsigned long st_mtime_nsec;
+ unsigned long st_ctime;
+ unsigned long st_ctime_nsec;
+ unsigned long __unused4;
+ unsigned long __unused5;
+};
+
+#endif /* __AVR32__ */
+
#ifdef __cplusplus
}
#endif
