Merge with http://opensource.freescale.com/pub/scm/u-boot-85xx.git#for_wd
diff --git a/CHANGELOG b/CHANGELOG
index 1604376..82be4e3 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,17 +2,255 @@
Changes since U-Boot 1.1.4:
======================================================================
+* Add support for WTK FO300 board (TQM5200 based).
+
+* Fix TQM834x hang.
+
+* Update for SC520 board.
+ Patch by David Updegraff, 02 Dec 2005
+
+* Fixed common.h spelling error.
+ Patch by Cory Tusar, 30 Nov 2005
+
+* Fix typo.
+ Patch by Andreas Engel, 28 Nov 2005
+
+* Fix fatload command on FAT32 formatted partitions.
+ Patch by Joachim Jaeger, 18 Nov 2005
+
+* Fix drivers/dm9000.c when configured in 32 bit mode.
+ Patch by Eric Benard, 17 Nov 2005
+
+* Cleanup debug code for yucca board.
+
+* MCC200: restrict addressable flash space to 32 MB
+
+* Add debug console on COM12 for MCC200 board
+
+* Fix control-c handing in CONFIG_CMDLINE_EDITING
+ Properly pass break code back from readline.
+ Patch by Roger Blofeld, 31 Jul 2006
+
+* Add commandline history support to all AMCC eval boards
+ Patch by Stefan Roese, 07 Aug 2006
+
+* Add Macronix MXLV320T flash support for AMCC Bamboo
+ Patch by Stefan Roese, 07 Aug 2006
+
+* Change "mii info" to not print an error upon missing PHY at address
+ Patch by Stefan Roese, 07 Aug 2006
+
+* Fix PCI-Express on PPC440SPe rev. A.
+
+* Fix preboot message on TQM85xx after switching to hush parser.
+
+* Adapt TQM85xx ramdisk address to Linux kernel memory map
+
+* Add initial support for PCI-Express on PPC440SPe (Yucca board).
+
+* Fix compiler warning for TRAB board.
+ Patch by Martin Krause, 07 Aug 2006
+
+* Prevent USB commands from working when USB is stopped.
+
+* Add rudimentary handling of alternate settings of USB interfaces.
+ This is in order to fix issues with some USB sticks timing out
+ during initialization. Some code readability improvements.
+
+* PPC440 DDR setup: Set SDRAM0_CFG0[PMU]=0 for best performance
+ AMCC suggested to set the PMU bit to 0 for best performace on
+ the PPC440 DDR controller.
+ Please see doc/README.440-DDR-performance for details.
+ Patch by Stefan Roese, 28 Jul 2006
+
+* AMCC bamboo (440EP) U-Boot image reduced to 384kbyte
+ Please see doc/README.bamboo for details.
+ Patch by Stefan Roese, 27 Jul 2006
+
+* Fix CONFIG_CMDLINE_EDITING implementation
+ Patch by Stefan Roese, 27 Jul 2006
+
+* Fix preboot message on TQM5200 after switching to hush parser.
+
+* MCC200: set default configuration to low_boot DDR,
+ and support for configurable options high_boot and/or SDRAM.
+
+* Add support for 256 MB SDRAM on CPU87
+ Patch by Josef Wagner, 25 Nov 2005
+
+* Add configuration for cam5200 board (based on TQM5200S).
+
+* More code cleanup
+
+* Disabled kvme080 board in MAKEALL because of build problems.
+
+* Code cleanup
+
+* Update NetStar board
+ Patch by Ladislav Michl, 03 Nov 2005
+
+* Make code better readable.
+ Patch by Ladislav Michl, 14 Sep 2005
+
+* Enable initrd ATAG for xm250 board.
+ Patch by Josef Wagner, 05 Sep 2005
+
+* Add readline cmdline-editing extension
+ Patch by JinHua Luo, 01 Sep 2005
+
+* Add support for friendly-arm SBC-2410X board
+ Patch by JinHua Luo, 01 Sep 2005
+
+* Fix multi-part image support on i386 platform.
+ Patch by David Updegraff, 19 Aug 2005
+
+* Add support for KVME080 board
+ Patch by Sangmoon Kim, 18 Aug 2005
+
+* Fix MIPS LE build problem
+ Patch by Matej Kupljen, 10 Aug 2005
+
+* Check argument count in "mii" command.
+ Problem pointed out by Andrew Dyer, 13 Jun 2005
+
+* Cleanup TQM5200 board configurations:
+ - make highboot configurations use environment at high end, too,
+ to avoid flash fragmentation
+ - always use redundand environment
+ - don't enable video code for modules without graphics controller
+ - provide useful (though different) mtdparts settings
+ - get rid of CONFIG_CS_AUTOCONF which was always set anyway
+
+* Extend mkconfig tool to print more useful target name
+
+* Add support for high-boot on TQM5200 and TQM5200S boards.
+ Hint: the CPLD on the TQM5200 must be programmed with a software
+ version supporting the high boot option! The new TQM5200S is
+ already supporting this option. On the TQM5200 this option will be
+ supported in configurations with MPC5200 rev B processors.
+ To actually "high boot", set jumper X30 on the STK52xx.
+ Patch by Martin Krause, 12 Jul 2006
+
+* Add support for new TQM5200 revisions
+ - Support for TQM5200S (short version without graphic controller)
+ - Support for modules with 'N' type S29GL128N Spansion flashes
+ (requires changes to flash layout)
+ - Support for MPC5200B cpu (mostly support for second SDRAM bank)
+ Patch by Martin Krause, 07 Jul 2006
+
+* Fix support for PS/2 keyboard on TQM85xx boards
+ The PS/2 keyobard driver for the TQM85xx modules only supports the
+ internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't
+ include a DUART, the TQM8560 modules can't be used with the PS/2
+ keyboard controller on the STK85xx board.
+ The PS/2 keyboard driver should work with the modules TQM8540,
+ TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet.
+ Make sure the PS/2 controller on the STK85xx is programmed. Jumper
+ settings: X66 1-2, 9-10; X61 2-3
+ Patch by Martin Krause, 21 Jun 2006
+
+* Adjust RTC century handling on STK52xx board to match Linux driver.
+ Patch by Martin Krause, 12 Jun 2006
+
+* Adjust filenames for USB update images on TRAB board.
+ During an automatic update via USB stick, U-Boot searches for
+ images with the name "firmware.img" and "kernel.img". This names
+ are now changed to "firmw_01.img" and "kernl_01.img". This is done,
+ to prevent updates of new boards (with the new macronics "c" step
+ flashes) with old, incompatible firmware or kernel versions.
+ Patch by Martin Krause, 21 Jun 2006
+
+* Bugfix in VFD routine on TRAB board.
+ Make sure upper lext pixel can be set to blue, too
+ (so far only red was possible).
+ Patch by Martin Krause, 15 Feb 2006
+
+* Enable buffered flash writes for TB5200 board.
+
+* Fix some bugs in TRAB board flash driver.
+ - increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds
+ - use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT
+ - remove "Unlock Bypass" mode, because macronix flashes do not support
+ this mode officially
+ - fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified
+ for Intel compatible flashes, not for AMD compatible.
+ Patch by Martin Krause, 15 Feb 2006
+
+* Add additional error messages to flash driver on TRAB board
+ (for erase errors and timeout errors)
+ Patch by Martin Krause, 14 Feb 2006
+
+* Add support for TB5200 board
+ The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
+ integrated in a little aluminium case.
+ Patch by Martin Krause, 8 Jun 2006
+
+* Enable buffered flash writes for TQM5200 board.
+
+* Fix problems with SanDisk Corporation Cruzer Micro USB memory stick.
+
+* Add support for TQM885D board.
+ Patch by Martin Krause, 20 Mar 2006
+
+* Fix FEC initialisation: All MII configuration is done via FEC1
+ registers, but MII_SPEED was configured according to FEC used. So
+ if only FEC2 was used, this caused the real MII_SPEED register in
+ FEC1 to stay uninitalised, leqading to "mii_send STUCK!" messages.
+ Fix: always configure MII_SPEED on FEC1 only.
+ Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* Add support for SPC1920 board.
+ Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* MCC200 board: support console on any one of the Quad UART ports.
+
+* Fix error in flash protection calculation on MCC200 board.
+
+* Major PCMCIA Cleanup to make code better readable and maintainable.
+ Notes:
+ - Board-dependend code for RPXLITE and RPXCLASSIC-based boards
+ placed to the drivers/rpx_pmcia.c file to avoid duplication.
+ Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
+ - drivers/i82365.c has been split into two parts located at
+ board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
+ the only boards using CONFIG_82365).
+ - Changes were tested for clean build and *very* *few* boards.
+
+* Fix timer problems on AMCC yucca board.
+ Set Timer Clock Select to use CPU clock as a timer input source.
+
+* Bring yucca config more in line with other AMCC boards.
+
+* Add AMCC bamboo board to MAKEALL build script.
+
+* Fix AMCC bamboo eval board compilation errors.
+
+* Add system memory to the PCI region list for AMCC PPC44x CPUs.
+ Enabled it for Yucca board.
+
+* Cleanup config file and bootup output for Yucca board.
+
+* Fix CONFIG_440_GX define usage.
+
+* Remove autogenerated bmp_logo.h file.
+
+* Add support for AMCC 440SPe CPU based eval board (Yucca).
+
+* Call serial_initialize() before first debug() is used.
+
+* Cleanup trab board for GCC-4.x
+
* VoiceBlue update: use new MTD flash partitioning methods, use more
reasonable TEXT_BASE, update default environment and enable keyed
autoboot.
- Patch by Ladislav Michl, 16. Aug 2005
+ Patch by Ladislav Michl, 16. Aug 2005
* Add forgotten changes for the PLEB 2 Board.
Patch by David Snowdon, 13. Aug 2005
* Add support for wrPPMC7xx/74xx boards
Patch by Richard Danter, 12 Aug 2005
-
+
* Add support for gth2 board
Patch by Thomas Lange, Aug 11 2005
@@ -34,7 +272,7 @@
With this fix pin I2CSCL (PG6) is really configured as GPIO
so the clock pulses are really generated.
Patch by Martin Krause, 04 Apr 2006
-
+
* Fix DDR6 errata on TQM834x boards
Patch by Thomas Waehner, 07 Mar 2006
@@ -51,7 +289,7 @@
has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3
* Fix TRAB channel switching delay for trab_fkt.bin standalone applikation
- In tsc2000_read_channel() the delay after setting the multiplexer
+ In tsc2000_read_channel() the delay after setting the multiplexer
to a temperature channel is increased from 1,5 ms to 10 ms. This
is to allow the multiplexer inputs to stabilize after huge steps
of the input signal level.
diff --git a/CREDITS b/CREDITS
index 94153a7..32d3060 100644
--- a/CREDITS
+++ b/CREDITS
@@ -233,6 +233,7 @@
N: Sangmoon Kim
E: dogoil@etinsys.com
D: Support for debris board
+D: Support for KVME080 board
N: Frederick W. Klatt
E: fred.klatt@windriver.com
diff --git a/MAINTAINERS b/MAINTAINERS
index aaf91cd..e1baa42 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -197,6 +197,7 @@
Sangmoon Kim <dogoil@etinsys.com>
debris MPC8245
+ KVME080 MPC8245
Thomas Lange <thomas@corelatus.se>
diff --git a/MAKEALL b/MAKEALL
index 804ea12..720ab03 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -25,16 +25,16 @@
#########################################################################
LIST_5xxx=" \
- BC3450 cpci5200 EVAL5200 icecube_5100 \
- icecube_5200 lite5200b mcc200 o2dnt \
- pf5200 PM520 Total5100 Total5200 \
- Total5200_Rev2 TQM5200 \
+ BC3450 cpci5200 EVAL5200 fo300 \
+ icecube_5100 icecube_5200 lite5200b mcc200 \
+ o2dnt pf5200 PM520 TB5200 \
+ Total5100 Total5200 Total5200_Rev2 TQM5200 \
+ TQM5200_B TQM5200S \
"
#########################################################################
## MPC8xx Systems
#########################################################################
-
LIST_8xx=" \
Adder87x GENIETV MBX860T R360MPI \
AdderII GTH MHPC RBC823 \
@@ -44,16 +44,18 @@
CCM IP860 NETPHONE RPXlite_DW \
cogent_mpc8xx IVML24 NETTA RRvision \
ELPT860 IVML24_128 NETTA2 SM850 \
- EP88x IVML24_256 NETTA_ISDN SPD823TS \
- ESTEEM192E IVMS8 NETVIA svm_sc8xx \
- ETX094 IVMS8_128 NETVIA_V2 SXNI855T \
- FADS823 IVMS8_256 NX823 TOP860 \
- FADS850SAR KUP4K pcu_e TQM823L \
- FADS860T KUP4X QS823 TQM823L_LCD \
- FLAGADM LANTEC QS850 TQM850L \
- FPS850L lwmon QS860T TQM855L \
- GEN860T MBX quantum TQM860L \
- GEN860T_SC uc100 \
+ EP88x IVML24_256 NETTA_ISDN spc1920 \
+ ESTEEM192E IVMS8 NETVIA SPD823TS \
+ ETX094 IVMS8_128 NETVIA_V2 svm_sc8xx \
+ FADS823 IVMS8_256 NX823 SXNI855T \
+ FADS850SAR KUP4K pcu_e TOP860 \
+ FADS860T KUP4X QS823 TQM823L \
+ FLAGADM LANTEC QS850 TQM823L_LCD \
+ FPS850L lwmon QS860T TQM850L \
+ GEN860T MBX quantum TQM855L \
+ GEN860T_SC TQM860L \
+ TQM885D \
+ uc100 \
v37 \
"
@@ -72,10 +74,10 @@
luan METROBOX MIP405 MIP405T \
ML2 ml300 ocotea OCRTC \
ORSG p3p440 PCI405 pcs440ep \
- PIP405 PLU405 PMC405 PPChameleonEVB \
- sbc405 VOH405 VOM405 W7OLMC \
+ PIP405 PLU405 PMC405 PPChameleonEVB \
+ sbc405 VOH405 VOM405 W7OLMC \
W7OLMG walnut WUH405 XPEDITE1K \
- yellowstone yosemite \
+ yellowstone yosemite yucca bamboo \
"
#########################################################################
@@ -93,9 +95,9 @@
LIST_824x=" \
A3000 barco BMW CPC45 \
CU824 debris eXalion HIDDEN_DRAGON \
- MOUSSE MUSENKI MVBLUE OXC \
- PN62 Sandpoint8240 Sandpoint8245 sbc8240 \
- SL8245 utx8245 \
+ MOUSSE MUSENKI MVBLUE \
+ OXC PN62 Sandpoint8240 Sandpoint8245 \
+ sbc8240 SL8245 utx8245 \
"
#########################################################################
@@ -179,9 +181,10 @@
ap966 cp920t cp922_XA10 cp926ejs \
cp946es cp966 lpd7a400 mp2usb \
mx1ads mx1fs2 netstar omap1510inn \
- omap1610h2 omap1610inn omap730p2 scb9328 \
- smdk2400 smdk2410 trab VCMA9 \
- versatile versatileab versatilepb voiceblue
+ omap1610h2 omap1610inn omap730p2 sbc2410x \
+ scb9328 smdk2400 smdk2410 trab \
+ VCMA9 versatile versatileab versatilepb \
+ voiceblue \
"
#########################################################################
@@ -301,7 +304,7 @@
${MAKE} distclean >/dev/null
${MAKE} ${target}_config
${MAKE} ${JOBS} all 2>&1 >LOG/$target.MAKELOG | tee LOG/$target.ERR
-# ${CROSS_COMPILE:-ppc_8xx-}size u-boot | tee -a LOG/$target.MAKELOG
+ ${CROSS_COMPILE:-ppc_8xx-}size u-boot | tee -a LOG/$target.MAKELOG
}
#-----------------------------------------------------------------------
diff --git a/Makefile b/Makefile
index 0b00819..a78f35b 100644
--- a/Makefile
+++ b/Makefile
@@ -7,7 +7,7 @@
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
+# published by the Free Software Foundatio; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
@@ -323,13 +323,30 @@
@./mkconfig -a IceCube ppc mpc5xxx icecube
mcc200_config \
-mcc200_lowboot_config: unconfig
+mcc200_SDRAM \
+mcc200_highboot \
+mcc200_COM12 \
+mcc200_highboot_SDRAM: unconfig
@ >include/config.h
- @[ -z "$(findstring lowboot_,$@)" ] || \
- { echo "TEXT_BASE = 0xFC000000" >board/mcc200/config.tmp ; \
- echo "... with lowboot configuration" ; \
+ @[ -n "$(findstring highboot,$@)" ] || \
+ { echo "... with lowboot configuration" ; \
}
- @./mkconfig mcc200 ppc mpc5xxx mcc200
+ @[ -z "$(findstring highboot,$@)" ] || \
+ { echo "TEXT_BASE = 0xFFF00000" >board/mcc200/config.tmp ; \
+ echo "... with highboot configuration" ; \
+ }
+ @[ -n "$(findstring _SDRAM,$@)" ] || \
+ { echo "... with DDR" ; \
+ }
+ @[ -z "$(findstring _SDRAM,$@)" ] || \
+ { echo "#define CONFIG_MCC200_SDRAM" >>include/config.h ; \
+ echo "... with SDRAM" ; \
+ }
+ @[ -z "$(findstring COM12,$@)" ] || \
+ { echo "#define CONFIG_CONSOLE_COM12" >>include/config.h ; \
+ echo "... with console on COM12" ; \
+ }
+ @./mkconfig -a mcc200 ppc mpc5xxx mcc200
o2dnt_config:
@./mkconfig o2dnt ppc mpc5xxx o2dnt
@@ -356,15 +373,21 @@
@./mkconfig -a smmaco4 ppc mpc5xxx tqm5200
spieval_config: unconfig
- @echo "#define CONFIG_CS_AUTOCONF">>include/config.h
- @echo "... with automatic CS configuration"
@./mkconfig -a spieval ppc mpc5xxx tqm5200
+TB5200_B_config \
+TB5200_config: unconfig
+ @[ -z "$(findstring _B,$@)" ] || \
+ { echo "#define CONFIG_TQM5200_B" >>include/config.h ; \
+ echo "... with MPC5200B processor" ; \
+ }
+ @./mkconfig -n $@ -a TB5200 ppc mpc5xxx tqm5200
+
MINI5200_config \
EVAL5200_config \
TOP5200_config: unconfig
@ echo "#define CONFIG_$(@:_config=) 1" >include/config.h
- @./mkconfig -a TOP5200 ppc mpc5xxx top5200 emk
+ @./mkconfig -n $@ -a TOP5200 ppc mpc5xxx top5200 emk
Total5100_config \
Total5200_config \
@@ -394,10 +417,26 @@
}
@./mkconfig -a Total5200 ppc mpc5xxx total5200
+cam5200_config \
+fo300_config \
+MiniFAP_config \
+TQM5200S_config \
+TQM5200S_HIGHBOOT_config \
+TQM5200_B_config \
+TQM5200_B_HIGHBOOT_config \
TQM5200_config \
-TQM5200_STK100_config \
-MiniFAP_config: unconfig
+TQM5200_STK100_config: unconfig
@ >include/config.h
+ @[ -z "$(findstring cam5200,$@)" ] || \
+ { echo "#define CONFIG_CAM5200" >>include/config.h ; \
+ echo "#define CONFIG_TQM5200S" >>include/config.h ; \
+ echo "#define CONFIG_TQM5200_B" >>include/config.h ; \
+ echo "... TQM5200S on Cam5200" ; \
+ }
+ @[ -z "$(findstring fo300,$@)" ] || \
+ { echo "#define CONFIG_FO300" >>include/config.h ; \
+ echo "... TQM5200 on FO300" ; \
+ }
@[ -z "$(findstring MiniFAP,$@)" ] || \
{ echo "#define CONFIG_MINIFAP" >>include/config.h ; \
echo "... TQM5200_AC on MiniFAP" ; \
@@ -406,9 +445,17 @@
{ echo "#define CONFIG_STK52XX_REV100" >>include/config.h ; \
echo "... on a STK52XX.100 base board" ; \
}
- @echo "#define CONFIG_CS_AUTOCONF">>include/config.h ;
- @echo "... with automatic CS configuration" ;
- @./mkconfig -a TQM5200 ppc mpc5xxx tqm5200
+ @[ -z "$(findstring TQM5200_B,$@)" ] || \
+ { echo "#define CONFIG_TQM5200_B" >>include/config.h ; \
+ }
+ @[ -z "$(findstring TQM5200S,$@)" ] || \
+ { echo "#define CONFIG_TQM5200S" >>include/config.h ; \
+ echo "#define CONFIG_TQM5200_B" >>include/config.h ; \
+ }
+ @[ -z "$(findstring HIGHBOOT,$@)" ] || \
+ { echo "TEXT_BASE = 0xFFF00000" >board/tqm5200/config.tmp ; \
+ }
+ @./mkconfig -n $@ -a TQM5200 ppc mpc5xxx tqm5200
#########################################################################
## MPC8xx Systems
@@ -705,6 +752,9 @@
SM850_config : unconfig
@./mkconfig $(@:_config=) ppc mpc8xx tqm8xx
+spc1920_config:
+ @./mkconfig $(@:_config=) ppc mpc8xx spc1920
+
SPD823TS_config: unconfig
@./mkconfig $(@:_config=) ppc mpc8xx spd8xx
@@ -742,6 +792,7 @@
TQM860M_config \
TQM862M_config \
TQM866M_config \
+TQM885D_config \
virtlab2_config: unconfig
@ >include/config.h
@[ -z "$(findstring _LCD,$@)" ] || \
@@ -981,6 +1032,9 @@
yellowstone_config: unconfig
@./mkconfig $(@:_config=) ppc ppc4xx yellowstone amcc
+yucca_config: unconfig
+ @./mkconfig $(@:_config=) ppc ppc4xx yucca amcc
+
#########################################################################
## MPC8220 Systems
#########################################################################
@@ -1031,6 +1085,9 @@
HIDDEN_DRAGON_config: unconfig
@./mkconfig $(@:_config=) ppc mpc824x hidden_dragon
+kvme080_config: unconfig
+ @./mkconfig $(@:_config=) ppc mpc824x kvme080 etin
+
MOUSSE_config: unconfig
@./mkconfig $(@:_config=) ppc mpc824x mousse
@@ -1454,7 +1511,7 @@
ppmc7xx_config: unconfig
@./mkconfig $(@:_config=) ppc 74xx_7xx ppmc7xx
-
+
#========================================================================
# ARM
#========================================================================
@@ -1588,6 +1645,9 @@
fi;
@./mkconfig -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 NULL omap
+sbc2410x_config: unconfig
+ @./mkconfig $(@:_config=) arm arm920t sbc2410x NULL s3c24x0
+
scb9328_config : unconfig
@./mkconfig $(@:_config=) arm arm920t scb9328 NULL imx
@@ -1968,6 +2028,7 @@
rm -f board/netstar/*.srec board/netstar/*.bin
rm -f board/trab/trab_fkt board/voiceblue/eeprom
rm -f board/integratorap/u-boot.lds board/integratorcp/u-boot.lds
+ rm -f include/bmp_logo.h
clobber: clean
find . -type f \( -name .depend \
diff --git a/README b/README
index 0fda03f..621f3f3 100644
--- a/README
+++ b/README
@@ -306,7 +306,7 @@
CONFIG_ARMADILLO, CONFIG_AT91RM9200DK, CONFIG_CERF250,
CONFIG_CSB637, CONFIG_DELTA, CONFIG_DNP1110,
- CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
+ CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
CONFIG_KB9202, CONFIG_LART, CONFIG_LPD7A400,
CONFIG_LUBBOCK, CONFIG_OSK_OMAP5912, CONFIG_OMAP2420H4,
@@ -1495,6 +1495,12 @@
of the backslashes before semicolons and special
symbols.
+- Commandline Editing and History:
+ CONFIG_CMDLINE_EDITING
+
+ Enable editiong and History functions for interactive
+ commandline input operations
+
- Default Environment:
CONFIG_EXTRA_ENV_SETTINGS
diff --git a/board/MAI/bios_emulator/scitech/src/pm/win32/event.c b/board/MAI/bios_emulator/scitech/src/pm/win32/event.c
index 86448e3..6388052 100644
--- a/board/MAI/bios_emulator/scitech/src/pm/win32/event.c
+++ b/board/MAI/bios_emulator/scitech/src/pm/win32/event.c
@@ -147,14 +147,14 @@
if (EVT.oldMove != -1) {
EVT.evtq[EVT.oldMove].where_x = evt.where_x;/* Modify existing one */
EVT.evtq[EVT.oldMove].where_y = evt.where_y;
-/* EVT.evtq[EVT.oldMove].relative_x += mickeyX; // TODO! */
-/* EVT.evtq[EVT.oldMove].relative_y += mickeyY; // TODO! */
+/* EVT.evtq[EVT.oldMove].relative_x += mickeyX; / / TODO! */
+/* EVT.evtq[EVT.oldMove].relative_y += mickeyY; / / TODO! */
evt.what = 0;
}
else {
EVT.oldMove = EVT.freeHead; /* Save id of this move event */
-/* evt.relative_x = mickeyX; // TODO! */
-/* evt.relative_y = mickeyY; // TODO! */
+/* evt.relative_x = mickeyX; / / TODO! */
+/* evt.relative_y = mickeyY; / / TODO! */
}
}
else
diff --git a/board/Marvell/include/core.h b/board/Marvell/include/core.h
index 081d5fd..c413439 100644
--- a/board/Marvell/include/core.h
+++ b/board/Marvell/include/core.h
@@ -91,7 +91,10 @@
#define _1G 0x40000000
#define _2G 0x80000000
+#ifndef BOOL_WAS_DEFINED
+#define BOOL_WAS_DEFINED
typedef enum _bool{false,true} bool;
+#endif
/* Little to Big endian conversion macros */
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index 7c98920..c93ba6e 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -435,7 +435,7 @@
*/
init_spd_array();
- dram_size = spd_sdram (0);
+ dram_size = spd_sdram();
return dram_size;
}
diff --git a/board/amcc/bamboo/bamboo.h b/board/amcc/bamboo/bamboo.h
index 5f5fcde..1ce6366 100644
--- a/board/amcc/bamboo/bamboo.h
+++ b/board/amcc/bamboo/bamboo.h
@@ -283,10 +283,8 @@
/*----------------------------------------------------------------------------+
| PPC440EP GPIOs addresses.
+----------------------------------------------------------------------------*/
-#define GPIO0_BASE 0xEF600B00
#define GPIO0_REAL 0xEF600B00
-#define GPIO1_BASE 0xEF600C00
#define GPIO1_REAL 0xEF600C00
/* Offsets */
@@ -332,17 +330,6 @@
/*----------------------------------------------------------------------------+
- | Declare Configuration values
- +----------------------------------------------------------------------------*/
-typedef enum gpio_select { GPIO_SEL, GPIO_ALT1, GPIO_ALT2, GPIO_ALT3 } gpio_select_t;
-typedef enum gpio_driver { GPIO_DIS, GPIO_IN, GPIO_OUT, GPIO_BI } gpio_driver_t;
-
-typedef struct { unsigned long add; /* gpio core base address */
- gpio_driver_t in_out; /* Driver Setting */
- gpio_select_t alt_nb; /* Selected Alternate */
-} gpio_param_s;
-
-/*----------------------------------------------------------------------------+
| XX XX
|
| XXXXXX XXX XX XXX XXX
diff --git a/board/amcc/bamboo/config.mk b/board/amcc/bamboo/config.mk
index 35cb655..9d7f4c3 100644
--- a/board/amcc/bamboo/config.mk
+++ b/board/amcc/bamboo/config.mk
@@ -1,5 +1,5 @@
#
-# (C) Copyright 2002
+# (C) Copyright 2002-2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
@@ -21,7 +21,7 @@
# MA 02111-1307 USA
#
-TEXT_BASE = 0xFFF80000
+TEXT_BASE = 0xFFFA0000
PLATFORM_CPPFLAGS += -DCONFIG_440=1
diff --git a/board/amcc/common/flash.c b/board/amcc/common/flash.c
index 3a50b09..a0acbba 100644
--- a/board/amcc/common/flash.c
+++ b/board/amcc/common/flash.c
@@ -76,6 +76,9 @@
case FLASH_MAN_SST:
printf("SST ");
break;
+ case FLASH_MAN_MX:
+ printf ("MACRONIX ");
+ break;
default:
printf("Unknown Vendor ");
break;
@@ -124,6 +127,9 @@
case FLASH_STMW320DT:
printf ("M29W320DT (32 M, top sector)\n");
break;
+ case FLASH_MXLV320T:
+ printf ("MXLV320T (32 Mbit, top sector)\n");
+ break;
default:
printf("Unknown Chip Type\n");
break;
@@ -375,6 +381,7 @@
{
if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T) ||
((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT)) {
return flash_erase_2(info, s_first, s_last);
} else {
@@ -555,6 +562,7 @@
{
if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T) ||
((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT)) {
return write_word_2(info, dest, data);
} else {
@@ -648,6 +656,9 @@
case (CFG_FLASH_WORD_SIZE) STM_MANUFACT:
info->flash_id = FLASH_MAN_STM;
break;
+ case (CFG_FLASH_WORD_SIZE) MX_MANUFACT:
+ info->flash_id = FLASH_MAN_MX;
+ break;
default:
info->flash_id = FLASH_UNKNOWN;
info->sector_count = 0;
@@ -676,6 +687,12 @@
info->sector_count = 67;
info->size = 0x00400000; break; /* => 4 MB */
+ case (CFG_FLASH_WORD_SIZE)MX_ID_LV320T:
+ info->flash_id += FLASH_MXLV320T;
+ info->sector_count = 71;
+ info->size = 0x00400000;
+ break; /* => 4 MB */
+
default:
info->flash_id = FLASH_UNKNOWN;
return (0); /* => no or unknown flash */
@@ -711,6 +728,19 @@
--i;
info->start[i] = base;
}
+ } else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T) {
+ i = info->sector_count - 1;
+ info->start[i--] = base + info->size - 0x00002000;
+ info->start[i--] = base + info->size - 0x00004000;
+ info->start[i--] = base + info->size - 0x00006000;
+ info->start[i--] = base + info->size - 0x00008000;
+ info->start[i--] = base + info->size - 0x0000a000;
+ info->start[i--] = base + info->size - 0x0000c000;
+ info->start[i--] = base + info->size - 0x0000e000;
+ info->start[i--] = base + info->size - 0x00010000;
+
+ for (; i >= 0; i--)
+ info->start[i] = base + i * 0x00010000;
} else {
if (info->flash_id & FLASH_BTYPE) {
/* set sector offsets for bottom boot block type */
diff --git a/board/amcc/yellowstone/yellowstone.c b/board/amcc/yellowstone/yellowstone.c
index 86d0db7..92dc9d4 100644
--- a/board/amcc/yellowstone/yellowstone.c
+++ b/board/amcc/yellowstone/yellowstone.c
@@ -313,13 +313,13 @@
mtsdram(mem_tr0, 0x410a4012); /* ?? */
mtsdram(mem_rtr, 0x04080000); /* ?? */
mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
- mtsdram(mem_cfg0, 0x34000000); /* Disable EEC */
+ mtsdram(mem_cfg0, 0x30000000); /* Disable EEC */
udelay(400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
- mtsdram(mem_cfg0, 0x84000000); /* Enable */
+ mtsdram(mem_cfg0, 0x80000000); /* Enable */
for (;;) {
mfsdram(mem_mcsts, reg);
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c
index 6742441..7f2e718 100644
--- a/board/amcc/yosemite/yosemite.c
+++ b/board/amcc/yosemite/yosemite.c
@@ -309,13 +309,13 @@
mtsdram(mem_tr0, 0x410a4012); /* ?? */
mtsdram(mem_rtr, 0x04080000); /* ?? */
mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
- mtsdram(mem_cfg0, 0x34000000); /* Disable EEC */
+ mtsdram(mem_cfg0, 0x30000000); /* Disable EEC */
udelay(400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
- mtsdram(mem_cfg0, 0x84000000); /* Enable */
+ mtsdram(mem_cfg0, 0x80000000); /* Enable */
for (;;) {
mfsdram(mem_mcsts, reg);
diff --git a/board/amcc/yucca/Makefile b/board/amcc/yucca/Makefile
new file mode 100644
index 0000000..c85fa31
--- /dev/null
+++ b/board/amcc/yucca/Makefile
@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = lib$(BOARD).a
+
+OBJS = $(BOARD).o flash.o cmd_yucca.o
+SOBJS = init.o
+
+$(LIB): $(OBJS) $(SOBJS)
+ $(AR) crv $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend *~
+
+#########################################################################
+
+.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+ $(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################
diff --git a/board/amcc/yucca/cmd_yucca.c b/board/amcc/yucca/cmd_yucca.c
new file mode 100644
index 0000000..e698b20
--- /dev/null
+++ b/board/amcc/yucca/cmd_yucca.c
@@ -0,0 +1,288 @@
+/*
+ * (C) Copyright 2001
+ * Denis Peter, MPL AG Switzerland, d.peter@mpl.ch
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * hacked for evb440spe
+ */
+
+#include <common.h>
+#include <command.h>
+#include "yucca.h"
+#include <i2c.h>
+#include <asm/byteorder.h>
+
+extern void print_evb440spe_info(void);
+static int setBootStrapClock(cmd_tbl_t *cmdtp, int incrflag,
+ int flag, int argc, char *argv[]);
+
+extern int cmd_get_data_size(char* arg, int default_size);
+
+/* ------------------------------------------------------------------------- */
+int do_evb440spe(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ return setBootStrapClock (cmdtp, 1, flag, argc, argv);
+}
+
+/* ------------------------------------------------------------------------- */
+/* Modify memory.
+ *
+ * Syntax:
+ * evb440spe wrclk prom0,prom1
+ */
+static int setBootStrapClock(cmd_tbl_t *cmdtp, int incrflag, int flag,
+ int argc, char *argv[])
+{
+ uchar chip;
+ ulong data;
+ int nbytes;
+ extern char console_buffer[];
+
+ char sysClock[4];
+ char cpuClock[4];
+ char plbClock[4];
+ char pcixClock[4];
+
+ if (argc < 3) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ if (strcmp(argv[2], "prom0") == 0)
+ chip = IIC0_BOOTPROM_ADDR;
+ else
+ chip = IIC0_ALT_BOOTPROM_ADDR;
+
+ do {
+ printf("enter sys clock frequency 33 or 66 Mhz or quit to abort\n");
+ nbytes = readline (" ? ");
+
+ if (strcmp(console_buffer, "quit") == 0)
+ return 0;
+
+ if ((strcmp(console_buffer, "33") != 0) &
+ (strcmp(console_buffer, "66") != 0))
+ nbytes=0;
+
+ strcpy(sysClock, console_buffer);
+
+ } while (nbytes == 0);
+
+ do {
+ if (strcmp(sysClock, "66") == 0) {
+ printf("enter cpu clock frequency 400, 533 Mhz or quit to abort\n");
+ } else {
+#ifdef CONFIG_STRESS
+ printf("enter cpu clock frequency 400, 500, 533, 667 Mhz or quit to abort\n");
+#else
+ printf("enter cpu clock frequency 400, 500, 533 Mhz or quit to abort\n");
+#endif
+ }
+ nbytes = readline (" ? ");
+
+ if (strcmp(console_buffer, "quit") == 0)
+ return 0;
+
+ if (strcmp(sysClock, "66") == 0) {
+ if ((strcmp(console_buffer, "400") != 0) &
+ (strcmp(console_buffer, "533") != 0)
+#ifdef CONFIG_STRESS
+ & (strcmp(console_buffer, "667") != 0)
+#endif
+ ) {
+ nbytes = 0;
+ }
+ } else {
+ if ((strcmp(console_buffer, "400") != 0) &
+ (strcmp(console_buffer, "500") != 0) &
+ (strcmp(console_buffer, "533") != 0)
+#ifdef CONFIG_STRESS
+ & (strcmp(console_buffer, "667") != 0)
+#endif
+ ) {
+ nbytes = 0;
+ }
+ }
+
+ strcpy(cpuClock, console_buffer);
+
+ } while (nbytes == 0);
+
+ if (strcmp(cpuClock, "500") == 0){
+ strcpy(plbClock, "166");
+ } else if (strcmp(cpuClock, "533") == 0){
+ strcpy(plbClock, "133");
+ } else {
+ do {
+ if (strcmp(cpuClock, "400") == 0)
+ printf("enter plb clock frequency 100, 133 Mhz or quit to abort\n");
+
+#ifdef CONFIG_STRESS
+ if (strcmp(cpuClock, "667") == 0)
+ printf("enter plb clock frequency 133, 166 Mhz or quit to abort\n");
+
+#endif
+ nbytes = readline (" ? ");
+
+ if (strcmp(console_buffer, "quit") == 0)
+ return 0;
+
+ if (strcmp(cpuClock, "400") == 0) {
+ if ((strcmp(console_buffer, "100") != 0) &
+ (strcmp(console_buffer, "133") != 0))
+ nbytes = 0;
+ }
+#ifdef CONFIG_STRESS
+ if (strcmp(cpuClock, "667") == 0) {
+ if ((strcmp(console_buffer, "133") != 0) &
+ (strcmp(console_buffer, "166") != 0))
+ nbytes = 0;
+ }
+#endif
+ strcpy(plbClock, console_buffer);
+
+ } while (nbytes == 0);
+ }
+
+ do {
+ printf("enter Pci-X clock frequency 33, 66, 100 or 133 Mhz or quit to abort\n");
+ nbytes = readline (" ? ");
+
+ if (strcmp(console_buffer, "quit") == 0)
+ return 0;
+
+ if ((strcmp(console_buffer, "33") != 0) &
+ (strcmp(console_buffer, "66") != 0) &
+ (strcmp(console_buffer, "100") != 0) &
+ (strcmp(console_buffer, "133") != 0)) {
+ nbytes = 0;
+ }
+ strcpy(pcixClock, console_buffer);
+
+ } while (nbytes == 0);
+
+ printf("\nsys clk = %sMhz\n", sysClock);
+ printf("cpu clk = %sMhz\n", cpuClock);
+ printf("plb clk = %sMhz\n", plbClock);
+ printf("Pci-X clk = %sMhz\n", pcixClock);
+
+ do {
+ printf("\npress [y] to write I2C bootstrap \n");
+ printf("or [n] to abort. \n");
+ printf("Don't forget to set board switches \n");
+ printf("according to your choice before re-starting \n");
+ printf("(refer to 440spe_uboot_kit_um_1_01.pdf) \n");
+
+ nbytes = readline (" ? ");
+ if (strcmp(console_buffer, "n") == 0)
+ return 0;
+
+ } while (nbytes == 0);
+
+ if (strcmp(sysClock, "33") == 0) {
+ if ((strcmp(cpuClock, "400") == 0) &
+ (strcmp(plbClock, "100") == 0))
+ data = 0x8678c206;
+
+ if ((strcmp(cpuClock, "400") == 0) &
+ (strcmp(plbClock, "133") == 0))
+ data = 0x8678c2c6;
+
+ if ((strcmp(cpuClock, "500") == 0))
+ data = 0x8778f2c6;
+
+ if ((strcmp(cpuClock, "533") == 0))
+ data = 0x87790252;
+
+#ifdef CONFIG_STRESS
+ if ((strcmp(cpuClock, "667") == 0) &
+ (strcmp(plbClock, "133") == 0))
+ data = 0x87794256;
+
+ if ((strcmp(cpuClock, "667") == 0) &
+ (strcmp(plbClock, "166") == 0))
+ data = 0x87794206;
+
+#endif
+ }
+ if (strcmp(sysClock, "66") == 0) {
+ if ((strcmp(cpuClock, "400") == 0) &
+ (strcmp(plbClock, "100") == 0))
+ data = 0x84706206;
+
+ if ((strcmp(cpuClock, "400") == 0) &
+ (strcmp(plbClock, "133") == 0))
+ data = 0x847062c6;
+
+ if ((strcmp(cpuClock, "533") == 0))
+ data = 0x85708206;
+
+#ifdef CONFIG_STRESS
+ if ((strcmp(cpuClock, "667") == 0) &
+ (strcmp(plbClock, "133") == 0))
+ data = 0x8570a256;
+
+ if ((strcmp(cpuClock, "667") == 0) &
+ (strcmp(plbClock, "166") == 0))
+ data = 0x8570a206;
+
+#endif
+ }
+
+#ifdef DEBUG
+ printf(" pin strap0 to write in i2c = %x\n", data);
+#endif /* DEBUG */
+
+ if (i2c_write(chip, 0, 1, (uchar *)&data, 4) != 0)
+ printf("Error writing strap0 in %s\n", argv[2]);
+
+ if (strcmp(pcixClock, "33") == 0)
+ data = 0x00000701;
+
+ if (strcmp(pcixClock, "66") == 0)
+ data = 0x00000601;
+
+ if (strcmp(pcixClock, "100") == 0)
+ data = 0x00000501;
+
+ if (strcmp(pcixClock, "133") == 0)
+ data = 0x00000401;
+
+ if (strcmp(plbClock, "166") == 0)
+ data = data | 0x05950000;
+ else
+ data = data | 0x05A50000;
+
+#ifdef DEBUG
+ printf(" pin strap1 to write in i2c = %x\n", data);
+#endif /* DEBUG */
+
+ udelay(1000);
+ if (i2c_write(chip, 4, 1, (uchar *)&data, 4) != 0)
+ printf("Error writing strap1 in %s\n", argv[2]);
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ evb440spe, 3, 1, do_evb440spe,
+ "evb440spe - program the serial device strap\n",
+ "wrclk [prom0|prom1] - program the serial device strap\n"
+);
diff --git a/board/amcc/yucca/config.mk b/board/amcc/yucca/config.mk
new file mode 100644
index 0000000..ff454eb
--- /dev/null
+++ b/board/amcc/yucca/config.mk
@@ -0,0 +1,42 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# AMCC 440SPe Reference Platform (yucca) board
+#
+
+ifeq ($(ramsym),1)
+TEXT_BASE = 0x07FD0000
+else
+TEXT_BASE = 0xfffb0000
+endif
+
+PLATFORM_CPPFLAGS += -DCONFIG_440=1
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
+
+ifeq ($(dbcr),1)
+PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+endif
diff --git a/board/amcc/yucca/flash.c b/board/amcc/yucca/flash.c
new file mode 100644
index 0000000..15b8a46
--- /dev/null
+++ b/board/amcc/yucca/flash.c
@@ -0,0 +1,1054 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2002 Jun Gu <jung@artesyncp.com>
+ * Add support for Am29F016D and dynamic switch setting.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Modified 4/5/2001
+ * Wait for completion of each sector erase command issued
+ * 4/5/2001
+ * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+#include <ppc440.h>
+#include "yucca.h"
+
+#ifdef DEBUG
+#define DEBUGF(x...) printf(x)
+#else
+#define DEBUGF(x...)
+#endif /* DEBUG */
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
+
+/*
+ * Mark big flash bank (16 bit instead of 8 bit access) in address with bit 0
+ */
+static unsigned long flash_addr_table[][CFG_MAX_FLASH_BANKS] = {
+ {0xfff00000, 0xfff80000, 0xe7c00001}, /* 0:boot from small flash */
+ {0x00000000, 0x00000000, 0x00000000}, /* 1:boot from pci 66 */
+ {0x00000000, 0x00000000, 0x00000000}, /* 2:boot from nand flash */
+ {0xe7F00000, 0xe7F80000, 0xFFC00001}, /* 3:boot from big flash 33*/
+ {0xe7F00000, 0xe7F80000, 0xFFC00001}, /* 4:boot from big flash 66*/
+ {0x00000000, 0x00000000, 0x00000000}, /* 5:boot from */
+ {0x00000000, 0x00000000, 0x00000000}, /* 6:boot from pci 66 */
+ {0x00000000, 0x00000000, 0x00000000}, /* 7:boot from */
+ {0xfff00000, 0xfff80000, 0xe7c00001}, /* 8:boot from small flash */
+};
+
+/*
+ * include common flash code (for amcc boards)
+ */
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static int write_word(flash_info_t * info, ulong dest, ulong data);
+#ifdef CFG_FLASH_2ND_16BIT_DEV
+static int write_word_1(flash_info_t * info, ulong dest, ulong data);
+static int write_word_2(flash_info_t * info, ulong dest, ulong data);
+static int flash_erase_1(flash_info_t * info, int s_first, int s_last);
+static int flash_erase_2(flash_info_t * info, int s_first, int s_last);
+static ulong flash_get_size_1(vu_long * addr, flash_info_t * info);
+static ulong flash_get_size_2(vu_long * addr, flash_info_t * info);
+#endif
+
+void flash_print_info(flash_info_t * info)
+{
+ int i;
+ int k;
+ int size;
+ int erased;
+ volatile unsigned long *flash;
+
+ if (info->flash_id == FLASH_UNKNOWN) {
+ printf("missing or unknown FLASH type\n");
+ return;
+ }
+
+ switch (info->flash_id & FLASH_VENDMASK) {
+ case FLASH_MAN_AMD:
+ printf("AMD ");
+ break;
+ case FLASH_MAN_STM:
+ printf("STM ");
+ break;
+ case FLASH_MAN_FUJ:
+ printf("FUJITSU ");
+ break;
+ case FLASH_MAN_SST:
+ printf("SST ");
+ break;
+ case FLASH_MAN_MX:
+ printf("MIXC ");
+ break;
+ default:
+ printf("Unknown Vendor ");
+ break;
+ }
+
+ switch (info->flash_id & FLASH_TYPEMASK) {
+ case FLASH_AM040:
+ printf("AM29F040 (512 Kbit, uniform sector size)\n");
+ break;
+ case FLASH_AM400B:
+ printf("AM29LV400B (4 Mbit, bottom boot sect)\n");
+ break;
+ case FLASH_AM400T:
+ printf("AM29LV400T (4 Mbit, top boot sector)\n");
+ break;
+ case FLASH_AM800B:
+ printf("AM29LV800B (8 Mbit, bottom boot sect)\n");
+ break;
+ case FLASH_AM800T:
+ printf("AM29LV800T (8 Mbit, top boot sector)\n");
+ break;
+ case FLASH_AMD016:
+ printf("AM29F016D (16 Mbit, uniform sector size)\n");
+ break;
+ case FLASH_AM160B:
+ printf("AM29LV160B (16 Mbit, bottom boot sect)\n");
+ break;
+ case FLASH_AM160T:
+ printf("AM29LV160T (16 Mbit, top boot sector)\n");
+ break;
+ case FLASH_AM320B:
+ printf("AM29LV320B (32 Mbit, bottom boot sect)\n");
+ break;
+ case FLASH_AM320T:
+ printf("AM29LV320T (32 Mbit, top boot sector)\n");
+ break;
+ case FLASH_AM033C:
+ printf("AM29LV033C (32 Mbit, top boot sector)\n");
+ break;
+ case FLASH_SST800A:
+ printf("SST39LF/VF800 (8 Mbit, uniform sector size)\n");
+ break;
+ case FLASH_SST160A:
+ printf("SST39LF/VF160 (16 Mbit, uniform sector size)\n");
+ break;
+ case FLASH_STMW320DT:
+ printf ("M29W320DT (32 M, top sector)\n");
+ break;
+ case FLASH_MXLV320T:
+ printf ("MXLV320T (32 Mbit, top sector)\n");
+ break;
+ default:
+ printf("Unknown Chip Type\n");
+ break;
+ }
+
+ printf(" Size: %ld KB in %d Sectors\n",
+ info->size >> 10, info->sector_count);
+
+ printf(" Sector Start Addresses:");
+ for (i = 0; i < info->sector_count; ++i) {
+ /*
+ * Check if whole sector is erased
+ */
+ if (i != (info->sector_count - 1))
+ size = info->start[i + 1] - info->start[i];
+ else
+ size = info->start[0] + info->size - info->start[i];
+ erased = 1;
+ flash = (volatile unsigned long *)info->start[i];
+ size = size >> 2; /* divide by 4 for longword access */
+ for (k = 0; k < size; k++) {
+ if (*flash++ != 0xffffffff) {
+ erased = 0;
+ break;
+ }
+ }
+
+ if ((i % 5) == 0)
+ printf("\n ");
+ printf(" %08lX%s%s",
+ info->start[i],
+ erased ? " E" : " ",
+ info->protect[i] ? "RO " : " ");
+ }
+ printf("\n");
+ return;
+}
+
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+#ifdef CFG_FLASH_2ND_16BIT_DEV
+static ulong flash_get_size(vu_long * addr, flash_info_t * info)
+{
+ /* bit 0 used for big flash marking */
+ if ((ulong)addr & 0x1)
+ return flash_get_size_2((vu_long *)((ulong)addr & 0xfffffffe), info);
+ else
+ return flash_get_size_1(addr, info);
+}
+
+static ulong flash_get_size_1(vu_long * addr, flash_info_t * info)
+#else
+static ulong flash_get_size(vu_long * addr, flash_info_t * info)
+#endif
+{
+ short i;
+ CFG_FLASH_WORD_SIZE value;
+ ulong base = (ulong) addr;
+ volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) addr;
+
+ DEBUGF("FLASH ADDR: %08x\n", (unsigned)addr);
+
+ /* Write auto select command: read Manufacturer ID */
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00900090;
+ udelay(1000);
+
+ value = addr2[0];
+ DEBUGF("FLASH MANUFACT: %x\n", value);
+
+ switch (value) {
+ case (CFG_FLASH_WORD_SIZE) AMD_MANUFACT:
+ info->flash_id = FLASH_MAN_AMD;
+ break;
+ case (CFG_FLASH_WORD_SIZE) FUJ_MANUFACT:
+ info->flash_id = FLASH_MAN_FUJ;
+ break;
+ case (CFG_FLASH_WORD_SIZE) SST_MANUFACT:
+ info->flash_id = FLASH_MAN_SST;
+ break;
+ case (CFG_FLASH_WORD_SIZE) STM_MANUFACT:
+ info->flash_id = FLASH_MAN_STM;
+ break;
+ default:
+ info->flash_id = FLASH_UNKNOWN;
+ info->sector_count = 0;
+ info->size = 0;
+ return (0); /* no or unknown flash */
+ }
+
+ value = addr2[1]; /* device ID */
+ DEBUGF("\nFLASH DEVICEID: %x\n", value);
+
+ switch (value) {
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_LV040B:
+ info->flash_id += FLASH_AM040;
+ info->sector_count = 8;
+ info->size = 0x0080000; /* => 512 ko */
+ break;
+
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_F040B:
+ info->flash_id += FLASH_AM040;
+ info->sector_count = 8;
+ info->size = 0x0080000; /* => 512 ko */
+ break;
+
+ case (CFG_FLASH_WORD_SIZE) STM_ID_M29W040B:
+ info->flash_id += FLASH_AM040;
+ info->sector_count = 8;
+ info->size = 0x0080000; /* => 512 ko */
+ break;
+
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_F016D:
+ info->flash_id += FLASH_AMD016;
+ info->sector_count = 32;
+ info->size = 0x00200000;
+ break; /* => 2 MB */
+
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_LV033C:
+ info->flash_id += FLASH_AMDLV033C;
+ info->sector_count = 64;
+ info->size = 0x00400000;
+ break; /* => 4 MB */
+
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_LV400T:
+ info->flash_id += FLASH_AM400T;
+ info->sector_count = 11;
+ info->size = 0x00080000;
+ break; /* => 0.5 MB */
+
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_LV400B:
+ info->flash_id += FLASH_AM400B;
+ info->sector_count = 11;
+ info->size = 0x00080000;
+ break; /* => 0.5 MB */
+
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_LV800T:
+ info->flash_id += FLASH_AM800T;
+ info->sector_count = 19;
+ info->size = 0x00100000;
+ break; /* => 1 MB */
+
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_LV800B:
+ info->flash_id += FLASH_AM800B;
+ info->sector_count = 19;
+ info->size = 0x00100000;
+ break; /* => 1 MB */
+
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_LV160T:
+ info->flash_id += FLASH_AM160T;
+ info->sector_count = 35;
+ info->size = 0x00200000;
+ break; /* => 2 MB */
+
+ case (CFG_FLASH_WORD_SIZE) AMD_ID_LV160B:
+ info->flash_id += FLASH_AM160B;
+ info->sector_count = 35;
+ info->size = 0x00200000;
+ break; /* => 2 MB */
+
+ default:
+ info->flash_id = FLASH_UNKNOWN;
+ return (0); /* => no or unknown flash */
+ }
+
+ /* set up sector start address table */
+ if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMD016)) {
+ for (i = 0; i < info->sector_count; i++)
+ info->start[i] = base + (i * 0x00010000);
+ } else {
+ if (info->flash_id & FLASH_BTYPE) {
+ /* set sector offsets for bottom boot block type */
+ info->start[0] = base + 0x00000000;
+ info->start[1] = base + 0x00004000;
+ info->start[2] = base + 0x00006000;
+ info->start[3] = base + 0x00008000;
+ for (i = 4; i < info->sector_count; i++) {
+ info->start[i] =
+ base + (i * 0x00010000) - 0x00030000;
+ }
+ } else {
+ /* set sector offsets for top boot block type */
+ i = info->sector_count - 1;
+ info->start[i--] = base + info->size - 0x00004000;
+ info->start[i--] = base + info->size - 0x00006000;
+ info->start[i--] = base + info->size - 0x00008000;
+ for (; i >= 0; i--) {
+ info->start[i] = base + i * 0x00010000;
+ }
+ }
+ }
+
+ /* check for protected sectors */
+ for (i = 0; i < info->sector_count; i++) {
+ /* read sector protection at sector address, (A7 .. A0) = 0x02 */
+ /* D0 = 1 if protected */
+ addr2 = (volatile CFG_FLASH_WORD_SIZE *)(info->start[i]);
+
+ /* For AMD29033C flash we need to resend the command of *
+ * reading flash protection for upper 8 Mb of flash */
+ if (i == 32) {
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA;
+ addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555;
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x90909090;
+ }
+
+ if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST)
+ info->protect[i] = 0;
+ else
+ info->protect[i] = addr2[2] & 1;
+ }
+
+ /* issue bank reset to return to read mode */
+ addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;
+
+ return (info->size);
+}
+
+static int wait_for_DQ7_1(flash_info_t * info, int sect)
+{
+ ulong start, now, last;
+ volatile CFG_FLASH_WORD_SIZE *addr =
+ (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
+
+ start = get_timer(0);
+ last = start;
+ while ((addr[0] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
+ (CFG_FLASH_WORD_SIZE) 0x00800080) {
+ if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+ printf("Timeout\n");
+ return -1;
+ }
+ /* show that we're waiting */
+ if ((now - last) > 1000) { /* every second */
+ putc('.');
+ last = now;
+ }
+ }
+ return 0;
+}
+
+#ifdef CFG_FLASH_2ND_16BIT_DEV
+int flash_erase(flash_info_t * info, int s_first, int s_last)
+{
+ if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T)) {
+ return flash_erase_2(info, s_first, s_last);
+ } else {
+ return flash_erase_1(info, s_first, s_last);
+ }
+}
+
+static int flash_erase_1(flash_info_t * info, int s_first, int s_last)
+#else
+int flash_erase(flash_info_t * info, int s_first, int s_last)
+#endif
+{
+ volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
+ volatile CFG_FLASH_WORD_SIZE *addr2;
+ int flag, prot, sect, l_sect;
+ int i;
+
+ if ((s_first < 0) || (s_first > s_last)) {
+ if (info->flash_id == FLASH_UNKNOWN)
+ printf("- missing\n");
+ else
+ printf("- no sectors to erase\n");
+ return 1;
+ }
+
+ if (info->flash_id == FLASH_UNKNOWN) {
+ printf("Can't erase unknown flash type - aborted\n");
+ return 1;
+ }
+
+ prot = 0;
+ for (sect = s_first; sect <= s_last; ++sect) {
+ if (info->protect[sect])
+ prot++;
+ }
+
+ if (prot)
+ printf("- Warning: %d protected sectors will not be erased!", prot);
+
+ printf("\n");
+
+ l_sect = -1;
+
+ /* Disable interrupts which might cause a timeout here */
+ flag = disable_interrupts();
+
+ /* Start erase on unprotected sectors */
+ for (sect = s_first; sect <= s_last; sect++) {
+ if (info->protect[sect] == 0) { /* not protected */
+ addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
+
+ if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00500050; /* block erase */
+ for (i = 0; i < 50; i++)
+ udelay(1000); /* wait 1 ms */
+ } else {
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00300030; /* sector erase */
+ }
+ l_sect = sect;
+ /*
+ * Wait for each sector to complete, it's more
+ * reliable. According to AMD Spec, you must
+ * issue all erase commands within a specified
+ * timeout. This has been seen to fail, especially
+ * if printf()s are included (for debug)!!
+ */
+ wait_for_DQ7_1(info, sect);
+ }
+ }
+
+ /* re-enable interrupts if necessary */
+ if (flag)
+ enable_interrupts();
+
+ /* wait at least 80us - let's wait 1 ms */
+ udelay(1000);
+
+ /* reset to read mode */
+ addr = (CFG_FLASH_WORD_SIZE *) info->start[0];
+ addr[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */
+
+ printf(" done\n");
+ return 0;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+ ulong cp, wp, data;
+ int i, l, rc;
+
+ wp = (addr & ~3); /* get lower word aligned address */
+
+ /*
+ * handle unaligned start bytes
+ */
+ if ((l = addr - wp) != 0) {
+ data = 0;
+ for (i = 0, cp = wp; i < l; ++i, ++cp)
+ data = (data << 8) | (*(uchar *) cp);
+
+ for (; i < 4 && cnt > 0; ++i) {
+ data = (data << 8) | *src++;
+ --cnt;
+ ++cp;
+ }
+
+ for (; cnt == 0 && i < 4; ++i, ++cp)
+ data = (data << 8) | (*(uchar *) cp);
+
+ if ((rc = write_word(info, wp, data)) != 0)
+ return (rc);
+
+ wp += 4;
+ }
+
+ /*
+ * handle word aligned part
+ */
+ while (cnt >= 4) {
+ data = 0;
+ for (i = 0; i < 4; ++i)
+ data = (data << 8) | *src++;
+
+ if ((rc = write_word(info, wp, data)) != 0)
+ return (rc);
+
+ wp += 4;
+ cnt -= 4;
+ }
+
+ if (cnt == 0)
+ return (0);
+
+ /*
+ * handle unaligned tail bytes
+ */
+ data = 0;
+ for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
+ data = (data << 8) | *src++;
+ --cnt;
+ }
+ for (; i < 4; ++i, ++cp)
+ data = (data << 8) | (*(uchar *) cp);
+
+ return (write_word(info, wp, data));
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+#ifdef CFG_FLASH_2ND_16BIT_DEV
+static int write_word(flash_info_t * info, ulong dest, ulong data)
+{
+ if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T)) {
+ return write_word_2(info, dest, data);
+ } else {
+ return write_word_1(info, dest, data);
+ }
+}
+
+static int write_word_1(flash_info_t * info, ulong dest, ulong data)
+#else
+static int write_word(flash_info_t * info, ulong dest, ulong data)
+#endif
+{
+ volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
+ volatile CFG_FLASH_WORD_SIZE *dest2 = (CFG_FLASH_WORD_SIZE *) dest;
+ volatile CFG_FLASH_WORD_SIZE *data2 = (CFG_FLASH_WORD_SIZE *) & data;
+ ulong start;
+ int i, flag;
+
+ /* Check if Flash is (sufficiently) erased */
+ if ((*((vu_long *)dest) & data) != data)
+ return (2);
+
+ for (i = 0; i < 4 / sizeof(CFG_FLASH_WORD_SIZE); i++) {
+ /* Disable interrupts which might cause a timeout here */
+ flag = disable_interrupts();
+
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00A000A0;
+
+ dest2[i] = data2[i];
+
+ /* re-enable interrupts if necessary */
+ if (flag)
+ enable_interrupts();
+
+ /* data polling for D7 */
+ start = get_timer(0);
+ while ((dest2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
+ (data2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080)) {
+
+ if (get_timer(start) > CFG_FLASH_WRITE_TOUT)
+ return (1);
+ }
+ }
+
+ return (0);
+}
+
+#ifdef CFG_FLASH_2ND_16BIT_DEV
+
+#undef CFG_FLASH_WORD_SIZE
+#define CFG_FLASH_WORD_SIZE unsigned short
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size_2(vu_long * addr, flash_info_t * info)
+{
+ short i;
+ int n;
+ CFG_FLASH_WORD_SIZE value;
+ ulong base = (ulong) addr;
+ volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) addr;
+
+ DEBUGF("FLASH ADDR: %08x\n", (unsigned)addr);
+
+ /* issue bank reset to return to read mode */
+ addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;
+ /* Write auto select command: read Manufacturer ID */
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00900090;
+ udelay(1000);
+
+ value = addr2[0];
+ DEBUGF("FLASH MANUFACT: %x\n", value);
+
+ switch (value) {
+ case (CFG_FLASH_WORD_SIZE) AMD_MANUFACT:
+ info->flash_id = FLASH_MAN_AMD;
+ break;
+ case (CFG_FLASH_WORD_SIZE) FUJ_MANUFACT:
+ info->flash_id = FLASH_MAN_FUJ;
+ break;
+ case (CFG_FLASH_WORD_SIZE) SST_MANUFACT:
+ info->flash_id = FLASH_MAN_SST;
+ break;
+ case (CFG_FLASH_WORD_SIZE) STM_MANUFACT:
+ info->flash_id = FLASH_MAN_STM;
+ break;
+ case (CFG_FLASH_WORD_SIZE) MX_MANUFACT:
+ info->flash_id = FLASH_MAN_MX;
+ break;
+ default:
+ info->flash_id = FLASH_UNKNOWN;
+ info->sector_count = 0;
+ info->size = 0;
+ return (0); /* no or unknown flash */
+ }
+
+ value = addr2[1]; /* device ID */
+ DEBUGF("\nFLASH DEVICEID: %x\n", value);
+
+ switch (value) {
+ case (CFG_FLASH_WORD_SIZE)AMD_ID_LV320T:
+ info->flash_id += FLASH_AM320T;
+ info->sector_count = 71;
+ info->size = 0x00400000;
+ break; /* => 4 MB */
+ case (CFG_FLASH_WORD_SIZE)AMD_ID_LV320B:
+ info->flash_id += FLASH_AM320B;
+ info->sector_count = 71;
+ info->size = 0x00400000;
+ break; /* => 4 MB */
+ case (CFG_FLASH_WORD_SIZE)STM_ID_29W320DT:
+ info->flash_id += FLASH_STMW320DT;
+ info->sector_count = 67;
+ info->size = 0x00400000;
+ break; /* => 4 MB */
+ case (CFG_FLASH_WORD_SIZE)MX_ID_LV320T:
+ info->flash_id += FLASH_MXLV320T;
+ info->sector_count = 71;
+ info->size = 0x00400000;
+ break; /* => 4 MB */
+ default:
+ info->flash_id = FLASH_UNKNOWN;
+ return (0); /* => no or unknown flash */
+ }
+
+ /* set up sector start address table */
+ if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMD016)) {
+ for (i = 0; i < info->sector_count; i++)
+ info->start[i] = base + (i * 0x00010000);
+ } else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT) {
+ /* set sector offsets for top boot block type */
+ base += info->size;
+ i = info->sector_count;
+ /* 1 x 16k boot sector */
+ base -= 16 << 10;
+ --i;
+ info->start[i] = base;
+ /* 2 x 8k boot sectors */
+ for (n = 0; n < 2; ++n) {
+ base -= 8 << 10;
+ --i;
+ info->start[i] = base;
+ }
+ /* 1 x 32k boot sector */
+ base -= 32 << 10;
+ --i;
+ info->start[i] = base;
+
+ while (i > 0) { /* 64k regular sectors */
+ base -= 64 << 10;
+ --i;
+ info->start[i] = base;
+ }
+ } else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T) {
+ i = info->sector_count - 1;
+ info->start[i--] = base + info->size - 0x00002000;
+ info->start[i--] = base + info->size - 0x00004000;
+ info->start[i--] = base + info->size - 0x00006000;
+ info->start[i--] = base + info->size - 0x00008000;
+ info->start[i--] = base + info->size - 0x0000a000;
+ info->start[i--] = base + info->size - 0x0000c000;
+ info->start[i--] = base + info->size - 0x0000e000;
+ info->start[i--] = base + info->size - 0x00010000;
+
+ for (; i >= 0; i--)
+ info->start[i] = base + i * 0x00010000;
+ } else {
+ if (info->flash_id & FLASH_BTYPE) {
+ /* set sector offsets for bottom boot block type */
+ info->start[0] = base + 0x00000000;
+ info->start[1] = base + 0x00004000;
+ info->start[2] = base + 0x00006000;
+ info->start[3] = base + 0x00008000;
+
+ for (i = 4; i < info->sector_count; i++)
+ info->start[i] = base + (i * 0x00010000) - 0x00030000;
+ } else {
+ /* set sector offsets for top boot block type */
+ i = info->sector_count - 1;
+ info->start[i--] = base + info->size - 0x00004000;
+ info->start[i--] = base + info->size - 0x00006000;
+ info->start[i--] = base + info->size - 0x00008000;
+
+ for (; i >= 0; i--)
+ info->start[i] = base + i * 0x00010000;
+ }
+ }
+
+ /* check for protected sectors */
+ for (i = 0; i < info->sector_count; i++) {
+ /* read sector protection at sector address, (A7 .. A0) = 0x02 */
+ /* D0 = 1 if protected */
+ addr2 = (volatile CFG_FLASH_WORD_SIZE *)(info->start[i]);
+
+ /* For AMD29033C flash we need to resend the command of *
+ * reading flash protection for upper 8 Mb of flash */
+ if (i == 32) {
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA;
+ addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555;
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x90909090;
+ }
+
+ if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST)
+ info->protect[i] = 0;
+ else
+ info->protect[i] = addr2[2] & 1;
+ }
+
+ /* issue bank reset to return to read mode */
+ addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;
+
+ return (info->size);
+}
+
+static int wait_for_DQ7_2(flash_info_t * info, int sect)
+{
+ ulong start, now, last;
+ volatile CFG_FLASH_WORD_SIZE *addr =
+ (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
+
+ start = get_timer(0);
+ last = start;
+ while ((addr[0] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
+ (CFG_FLASH_WORD_SIZE) 0x00800080) {
+ if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+ printf("Timeout\n");
+ return -1;
+ }
+ /* show that we're waiting */
+ if ((now - last) > 1000) { /* every second */
+ putc('.');
+ last = now;
+ }
+ }
+ return 0;
+}
+
+static int flash_erase_2(flash_info_t * info, int s_first, int s_last)
+{
+ volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
+ volatile CFG_FLASH_WORD_SIZE *addr2;
+ int flag, prot, sect, l_sect;
+ int i;
+
+ if ((s_first < 0) || (s_first > s_last)) {
+ if (info->flash_id == FLASH_UNKNOWN)
+ printf("- missing\n");
+ else
+ printf("- no sectors to erase\n");
+ return 1;
+ }
+
+ if (info->flash_id == FLASH_UNKNOWN) {
+ printf("Can't erase unknown flash type - aborted\n");
+ return 1;
+ }
+
+ prot = 0;
+ for (sect = s_first; sect <= s_last; ++sect) {
+ if (info->protect[sect])
+ prot++;
+ }
+
+ if (prot)
+ printf("- Warning: %d protected sectors will not be erased!", prot);
+
+ printf("\n");
+
+ l_sect = -1;
+
+ /* Disable interrupts which might cause a timeout here */
+ flag = disable_interrupts();
+
+ /* Start erase on unprotected sectors */
+ for (sect = s_first; sect <= s_last; sect++) {
+ if (info->protect[sect] == 0) { /* not protected */
+ addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
+
+ if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00500050; /* block erase */
+ for (i = 0; i < 50; i++)
+ udelay(1000); /* wait 1 ms */
+ } else {
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
+ addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00300030; /* sector erase */
+ }
+ l_sect = sect;
+ /*
+ * Wait for each sector to complete, it's more
+ * reliable. According to AMD Spec, you must
+ * issue all erase commands within a specified
+ * timeout. This has been seen to fail, especially
+ * if printf()s are included (for debug)!!
+ */
+ wait_for_DQ7_2(info, sect);
+ }
+ }
+
+ /* re-enable interrupts if necessary */
+ if (flag)
+ enable_interrupts();
+
+ /* wait at least 80us - let's wait 1 ms */
+ udelay(1000);
+
+ /* reset to read mode */
+ addr = (CFG_FLASH_WORD_SIZE *) info->start[0];
+ addr[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */
+
+ printf(" done\n");
+ return 0;
+}
+
+static int write_word_2(flash_info_t * info, ulong dest, ulong data)
+{
+ volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
+ volatile CFG_FLASH_WORD_SIZE *dest2 = (CFG_FLASH_WORD_SIZE *) dest;
+ volatile CFG_FLASH_WORD_SIZE *data2 = (CFG_FLASH_WORD_SIZE *) & data;
+ ulong start;
+ int i;
+
+ /* Check if Flash is (sufficiently) erased */
+ if ((*((vu_long *)dest) & data) != data)
+ return (2);
+
+ for (i = 0; i < 4 / sizeof(CFG_FLASH_WORD_SIZE); i++) {
+ int flag;
+
+ /* Disable interrupts which might cause a timeout here */
+ flag = disable_interrupts();
+
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
+ addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
+ addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00A000A0;
+
+ dest2[i] = data2[i];
+
+ /* re-enable interrupts if necessary */
+ if (flag)
+ enable_interrupts();
+
+ /* data polling for D7 */
+ start = get_timer(0);
+ while ((dest2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
+ (data2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080)) {
+
+ if (get_timer(start) > CFG_FLASH_WRITE_TOUT)
+ return (1);
+ }
+ }
+
+ return (0);
+}
+#endif /* CFG_FLASH_2ND_16BIT_DEV */
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size(vu_long * addr, flash_info_t * info);
+static int write_word(flash_info_t * info, ulong dest, ulong data);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init(void)
+{
+ unsigned long total_b = 0;
+ unsigned long size_b[CFG_MAX_FLASH_BANKS];
+ unsigned short index = 0;
+ int i;
+ unsigned long val;
+ unsigned long ebc_boot_size;
+ unsigned long boot_selection;
+
+ mfsdr(sdr_pstrp0, val);
+ index = (val & SDR0_PSTRP0_BOOTSTRAP_MASK) >> 28;
+
+ if ((index == 0xc) || (index == 8)) {
+ /*
+ * Boot Settings in IIC EEprom address 0xA8 or 0xA0
+ * Read Serial Device Strap Register1 in PPC440SPe
+ */
+ mfsdr(sdr_sdstp1, val);
+ boot_selection = val & SDR0_SDSTP1_BOOT_SEL_MASK;
+ ebc_boot_size = val & SDR0_SDSTP1_EBC_ROM_BS_MASK;
+
+ switch(boot_selection) {
+ case SDR0_SDSTP1_BOOT_SEL_EBC:
+ switch(ebc_boot_size) {
+ case SDR0_SDSTP1_EBC_ROM_BS_16BIT:
+ index = 3;
+ break;
+ case SDR0_SDSTP1_EBC_ROM_BS_8BIT:
+ index = 0;
+ break;
+ }
+ break;
+
+ case SDR0_SDSTP1_BOOT_SEL_PCI:
+ index = 1;
+ break;
+
+ }
+ } /*else if (index == 0) {*/
+/* if (in8(FPGA_SETTING_REG) & FPGA_SET_REG_OP_CODE_FLASH_ABOVE)*/
+/* index = 8;*/ /* sram below op code flash -> new index 8*/
+/* }*/
+
+ DEBUGF("\n");
+ DEBUGF("FLASH: Index: %d\n", index);
+
+ /* Init: no FLASHes known */
+ for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
+ flash_info[i].flash_id = FLASH_UNKNOWN;
+ flash_info[i].sector_count = -1;
+ flash_info[i].size = 0;
+
+ /* check whether the address is 0 */
+ if (flash_addr_table[index][i] == 0)
+ continue;
+
+ /* call flash_get_size() to initialize sector address */
+ size_b[i] = flash_get_size((vu_long *) flash_addr_table[index][i],
+ &flash_info[i]);
+
+ flash_info[i].size = size_b[i];
+
+ if (flash_info[i].flash_id == FLASH_UNKNOWN) {
+ printf("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
+ i, size_b[i], size_b[i] << 20);
+ flash_info[i].sector_count = -1;
+ flash_info[i].size = 0;
+ }
+
+ /* Monitor protection ON by default */
+ (void)flash_protect(FLAG_PROTECT_SET, CFG_MONITOR_BASE,
+ CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+ &flash_info[i]);
+#if defined(CFG_ENV_IS_IN_FLASH)
+ (void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR,
+ CFG_ENV_ADDR + CFG_ENV_SECT_SIZE - 1,
+ &flash_info[i]);
+#if defined(CFG_ENV_ADDR_REDUND)
+ (void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR_REDUND,
+ CFG_ENV_ADDR_REDUND + CFG_ENV_SECT_SIZE - 1,
+ &flash_info[i]);
+#endif
+#endif
+ total_b += flash_info[i].size;
+ }
+
+ return total_b;
+}
diff --git a/board/amcc/yucca/init.S b/board/amcc/yucca/init.S
new file mode 100644
index 0000000..c9eca68
--- /dev/null
+++ b/board/amcc/yucca/init.S
@@ -0,0 +1,152 @@
+/*
+ * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/* port to AMCC 440SPE evaluatioon board - SG April 12,2005 */
+
+#include <ppc_asm.tmpl>
+#include <config.h>
+
+/* General */
+#define TLB_VALID 0x00000200
+
+/* Supported page sizes */
+
+#define SZ_1K 0x00000000
+#define SZ_4K 0x00000010
+#define SZ_16K 0x00000020
+#define SZ_64K 0x00000030
+#define SZ_256K 0x00000040
+#define SZ_1M 0x00000050
+#define SZ_16M 0x00000070
+#define SZ_256M 0x00000090
+
+/* Storage attributes */
+#define SA_W 0x00000800 /* Write-through */
+#define SA_I 0x00000400 /* Caching inhibited */
+#define SA_M 0x00000200 /* Memory coherence */
+#define SA_G 0x00000100 /* Guarded */
+#define SA_E 0x00000080 /* Endian */
+
+/* Access control */
+#define AC_X 0x00000024 /* Execute */
+#define AC_W 0x00000012 /* Write */
+#define AC_R 0x00000009 /* Read */
+
+/* Some handy macros */
+
+#define EPN(e) ((e) & 0xfffffc00)
+#define TLB0(epn,sz) ((EPN((epn)) | (sz) | TLB_VALID ))
+#define TLB1(rpn,erpn) (((rpn) & 0xfffffc00) | (erpn))
+#define TLB2(a) ((a) & 0x00000fbf)
+
+#define tlbtab_start\
+ mflr r1 ;\
+ bl 0f ;
+
+#define tlbtab_end\
+ .long 0, 0, 0 ;\
+0: mflr r0 ;\
+ mtlr r1 ;\
+ blr ;
+
+#define tlbentry(epn,sz,rpn,erpn,attr)\
+ .long TLB0(epn,sz),TLB1(rpn,erpn),TLB2(attr)
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ * Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+
+ .section .bootpg,"ax"
+
+/**************************************************************************
+ * TLB table for revA
+ *************************************************************************/
+ .globl tlbtabA
+tlbtabA:
+ tlbtab_start
+ tlbentry(0xfff00000, SZ_16M, 0xfff00000, 4, AC_R|AC_W|AC_X|SA_G)
+
+ tlbentry(CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_SDRAM_BASE + 0x10000000, SZ_256M, 0x10000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_SDRAM_BASE + 0x20000000, SZ_256M, 0x20000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_SDRAM_BASE + 0x30000000, SZ_256M, 0x30000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+
+ tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
+ tlbentry(CFG_FPGA_BASE, SZ_1K, 0xE2000000, 4,AC_R|AC_W|SA_I)
+
+ tlbentry(CFG_OPER_FLASH, SZ_16M, 0xE7000000, 4,AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
+
+ tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE_BASE, SZ_16K, 0x20000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+
+ tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x40000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x80000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0xC0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x50000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x90000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0xD0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbtab_end
+
+/**************************************************************************
+ * TLB table for revB
+ *
+ * Notice: revB of the 440SPe chip is very strict about PLB real addresses
+ * and ranges to be mapped for config space: it seems to only work with
+ * d_nnnn_nnnn range (hangs the core upon config transaction attempts when
+ * set otherwise) while revA uses c_nnnn_nnnn.
+ *************************************************************************/
+ .globl tlbtabB
+tlbtabB:
+ tlbtab_start
+ tlbentry(0xfff00000, SZ_16M, 0xfff00000, 4, AC_R|AC_W|AC_X|SA_G)
+
+ tlbentry(CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_SDRAM_BASE + 0x10000000, SZ_256M, 0x10000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_SDRAM_BASE + 0x20000000, SZ_256M, 0x20000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_SDRAM_BASE + 0x30000000, SZ_256M, 0x30000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+
+ tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
+ tlbentry(CFG_FPGA_BASE, SZ_1K, 0xE2000000, 4,AC_R|AC_W|SA_I)
+
+ tlbentry(CFG_OPER_FLASH, SZ_16M, 0xE7000000, 4,AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
+
+ tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+
+ tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x00100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x20100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0x40100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0x50000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbtab_end
diff --git a/board/amcc/yucca/u-boot.lds b/board/amcc/yucca/u-boot.lds
new file mode 100644
index 0000000..9df4f92
--- /dev/null
+++ b/board/amcc/yucca/u-boot.lds
@@ -0,0 +1,157 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+SECTIONS
+{
+ .resetvec 0xFFFFFFFC :
+ {
+ *(.resetvec)
+ } = 0xffff
+
+ .bootpg 0xFFFFF000 :
+ {
+ cpu/ppc4xx/start.o (.bootpg)
+ } = 0xffff
+
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ /* WARNING - the following is hand-optimized to fit within */
+ /* the sector layout of our flash chips! XXX FIXME XXX */
+
+ cpu/ppc4xx/start.o (.text)
+ board/amcc/yucca/init.o (.text)
+ cpu/ppc4xx/kgdb.o (.text)
+ cpu/ppc4xx/traps.o (.text)
+ cpu/ppc4xx/interrupts.o (.text)
+ cpu/ppc4xx/serial.o (.text)
+ cpu/ppc4xx/cpu_init.o (.text)
+ cpu/ppc4xx/speed.o (.text)
+ common/dlmalloc.o (.text)
+ lib_generic/crc32.o (.text)
+ lib_ppc/extable.o (.text)
+ lib_generic/zlib.o (.text)
+
+/* . = env_offset;*/
+/* common/environment.o(.text)*/
+
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ *(.eh_frame)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+ __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
diff --git a/board/amcc/yucca/u-boot.lds.debug b/board/amcc/yucca/u-boot.lds.debug
new file mode 100644
index 0000000..474f922
--- /dev/null
+++ b/board/amcc/yucca/u-boot.lds.debug
@@ -0,0 +1,146 @@
+/*
+ * (C) Copyright 2002-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ /* WARNING - the following is hand-optimized to fit within */
+ /* the sector layout of our flash chips! XXX FIXME XXX */
+
+ cpu/ppc4xx/start.o (.text)
+ board/amcc/yucca/init.o (.text)
+ cpu/ppc4xx/kgdb.o (.text)
+ cpu/ppc4xx/traps.o (.text)
+ cpu/ppc4xx/interrupts.o (.text)
+ cpu/ppc4xx/serial.o (.text)
+ cpu/ppc4xx/cpu_init.o (.text)
+ cpu/ppc4xx/speed.o (.text)
+ common/dlmalloc.o (.text)
+ lib_generic/crc32.o (.text)
+ lib_ppc/extable.o (.text)
+ lib_generic/zlib.o (.text)
+
+/* common/environment.o(.text) */
+
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ *(.eh_frame)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x0FFF) & 0xFFFFF000;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+ __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
new file mode 100644
index 0000000..af12839
--- /dev/null
+++ b/board/amcc/yucca/yucca.c
@@ -0,0 +1,1224 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Port to AMCC-440SPE Evaluation Board SOP - April 2005
+ *
+ * PCIe supporting routines derived from Linux 440SPe PCIe driver.
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+#include <i2c.h>
+#include <asm-ppc/io.h>
+
+#include "yucca.h"
+
+void fpga_init (void);
+
+void get_sys_info(PPC440_SYS_INFO *board_cfg );
+int compare_to_true(char *str );
+char *remove_l_w_space(char *in_str );
+char *remove_t_w_space(char *in_str );
+int get_console_port(void);
+unsigned long ppcMfcpr(unsigned long cpr_reg);
+unsigned long ppcMfsdr(unsigned long sdr_reg);
+
+int ppc440spe_init_pcie_rootport(int port);
+void ppc440spe_setup_pcie(struct pci_controller *hose, int port);
+
+#define DEBUG_ENV
+#ifdef DEBUG_ENV
+#define DEBUGF(fmt,args...) printf(fmt ,##args)
+#else
+#define DEBUGF(fmt,args...)
+#endif
+
+#define FALSE 0
+#define TRUE 1
+
+int board_early_init_f (void)
+{
+/*----------------------------------------------------------------------------+
+| Define Boot devices
++----------------------------------------------------------------------------*/
+#define BOOT_FROM_SMALL_FLASH 0x00
+#define BOOT_FROM_LARGE_FLASH_OR_SRAM 0x01
+#define BOOT_FROM_PCI 0x02
+#define BOOT_DEVICE_UNKNOWN 0x03
+
+/*----------------------------------------------------------------------------+
+| EBC Devices Characteristics
+| Peripheral Bank Access Parameters - EBC_BxAP
+| Peripheral Bank Configuration Register - EBC_BxCR
++----------------------------------------------------------------------------*/
+
+/*
+ * Small Flash and FRAM
+ * BU Value
+ * BxAP : 0x03800000 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000
+ * B0CR : 0xff098000 - BAS = ff0 - 100 11 00 0000000000000
+ * B2CR : 0xe7098000 - BAS = e70 - 100 11 00 0000000000000
+ */
+#define EBC_BXAP_SMALL_FLASH EBC_BXAP_BME_DISABLED | \
+ EBC_BXAP_TWT_ENCODE(7) | \
+ EBC_BXAP_BCE_DISABLE | \
+ EBC_BXAP_BCT_2TRANS | \
+ EBC_BXAP_CSN_ENCODE(0) | \
+ EBC_BXAP_OEN_ENCODE(0) | \
+ EBC_BXAP_WBN_ENCODE(0) | \
+ EBC_BXAP_WBF_ENCODE(0) | \
+ EBC_BXAP_TH_ENCODE(0) | \
+ EBC_BXAP_RE_DISABLED | \
+ EBC_BXAP_SOR_DELAYED | \
+ EBC_BXAP_BEM_WRITEONLY | \
+ EBC_BXAP_PEN_DISABLED
+
+#define EBC_BXCR_SMALL_FLASH_CS0 EBC_BXCR_BAS_ENCODE(0xFF000000) | \
+ EBC_BXCR_BS_16MB | \
+ EBC_BXCR_BU_RW | \
+ EBC_BXCR_BW_8BIT
+
+#define EBC_BXCR_SMALL_FLASH_CS2 EBC_BXCR_BAS_ENCODE(0xe7000000) | \
+ EBC_BXCR_BS_16MB | \
+ EBC_BXCR_BU_RW | \
+ EBC_BXCR_BW_8BIT
+
+/*
+ * Large Flash and SRAM
+ * BU Value
+ * BxAP : 0x048ff240 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000
+ * B0CR : 0xff09a000 - BAS = ff0 - 100 11 01 0000000000000
+ * B2CR : 0xe709a000 - BAS = e70 - 100 11 01 0000000000000
+*/
+#define EBC_BXAP_LARGE_FLASH EBC_BXAP_BME_DISABLED | \
+ EBC_BXAP_TWT_ENCODE(7) | \
+ EBC_BXAP_BCE_DISABLE | \
+ EBC_BXAP_BCT_2TRANS | \
+ EBC_BXAP_CSN_ENCODE(0) | \
+ EBC_BXAP_OEN_ENCODE(0) | \
+ EBC_BXAP_WBN_ENCODE(0) | \
+ EBC_BXAP_WBF_ENCODE(0) | \
+ EBC_BXAP_TH_ENCODE(0) | \
+ EBC_BXAP_RE_DISABLED | \
+ EBC_BXAP_SOR_DELAYED | \
+ EBC_BXAP_BEM_WRITEONLY | \
+ EBC_BXAP_PEN_DISABLED
+
+#define EBC_BXCR_LARGE_FLASH_CS0 EBC_BXCR_BAS_ENCODE(0xFF000000) | \
+ EBC_BXCR_BS_16MB | \
+ EBC_BXCR_BU_RW | \
+ EBC_BXCR_BW_16BIT
+
+#define EBC_BXCR_LARGE_FLASH_CS2 EBC_BXCR_BAS_ENCODE(0xE7000000) | \
+ EBC_BXCR_BS_16MB | \
+ EBC_BXCR_BU_RW | \
+ EBC_BXCR_BW_16BIT
+
+/*
+ * FPGA
+ * BU value :
+ * B1AP = 0x05895240 - 0 00001011 0 00 10 01 01 01 001 0 0 1 0 00000
+ * B1CR = 0xe201a000 - BAS = e20 - 000 11 01 00000000000000
+ */
+#define EBC_BXAP_FPGA EBC_BXAP_BME_DISABLED | \
+ EBC_BXAP_TWT_ENCODE(11) | \
+ EBC_BXAP_BCE_DISABLE | \
+ EBC_BXAP_BCT_2TRANS | \
+ EBC_BXAP_CSN_ENCODE(10) | \
+ EBC_BXAP_OEN_ENCODE(1) | \
+ EBC_BXAP_WBN_ENCODE(1) | \
+ EBC_BXAP_WBF_ENCODE(1) | \
+ EBC_BXAP_TH_ENCODE(1) | \
+ EBC_BXAP_RE_DISABLED | \
+ EBC_BXAP_SOR_DELAYED | \
+ EBC_BXAP_BEM_RW | \
+ EBC_BXAP_PEN_DISABLED
+
+#define EBC_BXCR_FPGA_CS1 EBC_BXCR_BAS_ENCODE(0xe2000000) | \
+ EBC_BXCR_BS_1MB | \
+ EBC_BXCR_BU_RW | \
+ EBC_BXCR_BW_16BIT
+
+ unsigned long mfr;
+ /*
+ * Define Variables for EBC initialization depending on BOOTSTRAP option
+ */
+ unsigned long sdr0_pinstp, sdr0_sdstp1 ;
+ unsigned long bootstrap_settings, ebc_data_width, boot_selection;
+ int computed_boot_device = BOOT_DEVICE_UNKNOWN;
+
+ /*-------------------------------------------------------------------+
+ | Initialize EBC CONFIG -
+ | Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
+ | default value :
+ | 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
+ |
+ +-------------------------------------------------------------------*/
+ mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+ EBC_CFG_PTD_ENABLE |
+ EBC_CFG_RTC_16PERCLK |
+ EBC_CFG_ATC_PREVIOUS |
+ EBC_CFG_DTC_PREVIOUS |
+ EBC_CFG_CTC_PREVIOUS |
+ EBC_CFG_OEO_PREVIOUS |
+ EBC_CFG_EMC_DEFAULT |
+ EBC_CFG_PME_DISABLE |
+ EBC_CFG_PR_16);
+
+ /*-------------------------------------------------------------------+
+ |
+ | PART 1 : Initialize EBC Bank 1
+ | ==============================
+ | Bank1 is always associated to the EPLD.
+ | It has to be initialized prior to other banks settings computation
+ | since some board registers values may be needed to determine the
+ | boot type
+ |
+ +-------------------------------------------------------------------*/
+ mtebc(pb1ap, EBC_BXAP_FPGA);
+ mtebc(pb1cr, EBC_BXCR_FPGA_CS1);
+
+ /*-------------------------------------------------------------------+
+ |
+ | PART 2 : Determine which boot device was selected
+ | =================================================
+ |
+ | Read Pin Strap Register in PPC440SPe
+ | Result can either be :
+ | - Boot strap = boot from EBC 8bits => Small Flash
+ | - Boot strap = boot from PCI
+ | - Boot strap = IIC
+ | In case of boot from IIC, read Serial Device Strap Register1
+ |
+ | Result can either be :
+ | - Boot from EBC - EBC Bus Width = 8bits => Small Flash
+ | - Boot from EBC - EBC Bus Width = 16bits => Large Flash or SRAM
+ | - Boot from PCI
+ |
+ +-------------------------------------------------------------------*/
+ /* Read Pin Strap Register in PPC440SP */
+ sdr0_pinstp = ppcMfsdr(SDR0_PINSTP);
+ bootstrap_settings = sdr0_pinstp & SDR0_PINSTP_BOOTSTRAP_MASK;
+
+ switch (bootstrap_settings) {
+ case SDR0_PINSTP_BOOTSTRAP_SETTINGS0:
+ /*
+ * Strapping Option A
+ * Boot from EBC - 8 bits , Small Flash
+ */
+ computed_boot_device = BOOT_FROM_SMALL_FLASH;
+ break;
+ case SDR0_PINSTP_BOOTSTRAP_SETTINGS1:
+ /*
+ * Strappping Option B
+ * Boot from PCI
+ */
+ computed_boot_device = BOOT_FROM_PCI;
+ break;
+ case SDR0_PINSTP_BOOTSTRAP_IIC_50_EN:
+ case SDR0_PINSTP_BOOTSTRAP_IIC_54_EN:
+ /*
+ * Strapping Option C or D
+ * Boot Settings in IIC EEprom address 0x50 or 0x54
+ * Read Serial Device Strap Register1 in PPC440SPe
+ */
+ sdr0_sdstp1 = ppcMfsdr(SDR0_SDSTP1);
+ boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_ERPN_MASK;
+ ebc_data_width = sdr0_sdstp1 & SDR0_SDSTP1_EBCW_MASK;
+
+ switch (boot_selection) {
+ case SDR0_SDSTP1_ERPN_EBC:
+ switch (ebc_data_width) {
+ case SDR0_SDSTP1_EBCW_16_BITS:
+ computed_boot_device =
+ BOOT_FROM_LARGE_FLASH_OR_SRAM;
+ break;
+ case SDR0_SDSTP1_EBCW_8_BITS :
+ computed_boot_device = BOOT_FROM_SMALL_FLASH;
+ break;
+ }
+ break;
+
+ case SDR0_SDSTP1_ERPN_PCI:
+ computed_boot_device = BOOT_FROM_PCI;
+ break;
+ default:
+ /* should not occure */
+ computed_boot_device = BOOT_DEVICE_UNKNOWN;
+ }
+ break;
+ default:
+ /* should not be */
+ computed_boot_device = BOOT_DEVICE_UNKNOWN;
+ break;
+ }
+
+ /*-------------------------------------------------------------------+
+ |
+ | PART 3 : Compute EBC settings depending on selected boot device
+ | ====== ======================================================
+ |
+ | Resulting EBC init will be among following configurations :
+ |
+ | - Boot from EBC 8bits => boot from Small Flash selected
+ | EBC-CS0 = Small Flash
+ | EBC-CS2 = Large Flash and SRAM
+ |
+ | - Boot from EBC 16bits => boot from Large Flash or SRAM
+ | EBC-CS0 = Large Flash or SRAM
+ | EBC-CS2 = Small Flash
+ |
+ | - Boot from PCI
+ | EBC-CS0 = not initialized to avoid address contention
+ | EBC-CS2 = same as boot from Small Flash selected
+ |
+ +-------------------------------------------------------------------*/
+ unsigned long ebc0_cs0_bxap_value = 0, ebc0_cs0_bxcr_value = 0;
+ unsigned long ebc0_cs2_bxap_value = 0, ebc0_cs2_bxcr_value = 0;
+
+ switch (computed_boot_device) {
+ /*-------------------------------------------------------------------*/
+ case BOOT_FROM_PCI:
+ /*-------------------------------------------------------------------*/
+ /*
+ * By Default CS2 is affected to LARGE Flash
+ * do not initialize SMALL FLASH to avoid address contention
+ * Large Flash
+ */
+ ebc0_cs2_bxap_value = EBC_BXAP_LARGE_FLASH;
+ ebc0_cs2_bxcr_value = EBC_BXCR_LARGE_FLASH_CS2;
+ break;
+
+ /*-------------------------------------------------------------------*/
+ case BOOT_FROM_SMALL_FLASH:
+ /*-------------------------------------------------------------------*/
+ ebc0_cs0_bxap_value = EBC_BXAP_SMALL_FLASH;
+ ebc0_cs0_bxcr_value = EBC_BXCR_SMALL_FLASH_CS0;
+
+ /*
+ * Large Flash or SRAM
+ */
+ /* ebc0_cs2_bxap_value = EBC_BXAP_LARGE_FLASH; */
+ ebc0_cs2_bxap_value = 0x048ff240;
+ ebc0_cs2_bxcr_value = EBC_BXCR_LARGE_FLASH_CS2;
+ break;
+
+ /*-------------------------------------------------------------------*/
+ case BOOT_FROM_LARGE_FLASH_OR_SRAM:
+ /*-------------------------------------------------------------------*/
+ ebc0_cs0_bxap_value = EBC_BXAP_LARGE_FLASH;
+ ebc0_cs0_bxcr_value = EBC_BXCR_LARGE_FLASH_CS0;
+
+ /* Small flash */
+ ebc0_cs2_bxap_value = EBC_BXAP_SMALL_FLASH;
+ ebc0_cs2_bxcr_value = EBC_BXCR_SMALL_FLASH_CS2;
+ break;
+
+ /*-------------------------------------------------------------------*/
+ default:
+ /*-------------------------------------------------------------------*/
+ /* BOOT_DEVICE_UNKNOWN */
+ break;
+ }
+
+ mtebc(pb0ap, ebc0_cs0_bxap_value);
+ mtebc(pb0cr, ebc0_cs0_bxcr_value);
+ mtebc(pb2ap, ebc0_cs2_bxap_value);
+ mtebc(pb2cr, ebc0_cs2_bxcr_value);
+
+ /*--------------------------------------------------------------------+
+ | Interrupt controller setup for the AMCC 440SPe Evaluation board.
+ +--------------------------------------------------------------------+
+ +---------------------------------------------------------------------+
+ |Interrupt| Source | Pol. | Sensi.| Crit. |
+ +---------+-----------------------------------+-------+-------+-------+
+ | IRQ 00 | UART0 | High | Level | Non |
+ | IRQ 01 | UART1 | High | Level | Non |
+ | IRQ 02 | IIC0 | High | Level | Non |
+ | IRQ 03 | IIC1 | High | Level | Non |
+ | IRQ 04 | PCI0X0 MSG IN | High | Level | Non |
+ | IRQ 05 | PCI0X0 CMD Write | High | Level | Non |
+ | IRQ 06 | PCI0X0 Power Mgt | High | Level | Non |
+ | IRQ 07 | PCI0X0 VPD Access | Rising| Edge | Non |
+ | IRQ 08 | PCI0X0 MSI level 0 | High | Lvl/ed| Non |
+ | IRQ 09 | External IRQ 15 - (PCI-Express) | pgm H | Pgm | Non |
+ | IRQ 10 | UIC2 Non-critical Int. | NA | NA | Non |
+ | IRQ 11 | UIC2 Critical Interrupt | NA | NA | Crit |
+ | IRQ 12 | PCI Express MSI Level 0 | Rising| Edge | Non |
+ | IRQ 13 | PCI Express MSI Level 1 | Rising| Edge | Non |
+ | IRQ 14 | PCI Express MSI Level 2 | Rising| Edge | Non |
+ | IRQ 15 | PCI Express MSI Level 3 | Rising| Edge | Non |
+ | IRQ 16 | UIC3 Non-critical Int. | NA | NA | Non |
+ | IRQ 17 | UIC3 Critical Interrupt | NA | NA | Crit |
+ | IRQ 18 | External IRQ 14 - (PCI-Express) | Pgm | Pgm | Non |
+ | IRQ 19 | DMA Channel 0 FIFO Full | High | Level | Non |
+ | IRQ 20 | DMA Channel 0 Stat FIFO | High | Level | Non |
+ | IRQ 21 | DMA Channel 1 FIFO Full | High | Level | Non |
+ | IRQ 22 | DMA Channel 1 Stat FIFO | High | Level | Non |
+ | IRQ 23 | I2O Inbound Doorbell | High | Level | Non |
+ | IRQ 24 | Inbound Post List FIFO Not Empt | High | Level | Non |
+ | IRQ 25 | I2O Region 0 LL PLB Write | High | Level | Non |
+ | IRQ 26 | I2O Region 1 LL PLB Write | High | Level | Non |
+ | IRQ 27 | I2O Region 0 HB PLB Write | High | Level | Non |
+ | IRQ 28 | I2O Region 1 HB PLB Write | High | Level | Non |
+ | IRQ 29 | GPT Down Count Timer | Rising| Edge | Non |
+ | IRQ 30 | UIC1 Non-critical Int. | NA | NA | Non |
+ | IRQ 31 | UIC1 Critical Interrupt | NA | NA | Crit. |
+ |----------------------------------------------------------------------
+ | IRQ 32 | Ext. IRQ 13 - (PCI-Express) |pgm (H)|pgm/Lvl| Non |
+ | IRQ 33 | MAL Serr | High | Level | Non |
+ | IRQ 34 | MAL Txde | High | Level | Non |
+ | IRQ 35 | MAL Rxde | High | Level | Non |
+ | IRQ 36 | DMC CE or DMC UE | High | Level | Non |
+ | IRQ 37 | EBC or UART2 | High |Lvl Edg| Non |
+ | IRQ 38 | MAL TX EOB | High | Level | Non |
+ | IRQ 39 | MAL RX EOB | High | Level | Non |
+ | IRQ 40 | PCIX0 MSI Level 1 | High |Lvl Edg| Non |
+ | IRQ 41 | PCIX0 MSI level 2 | High |Lvl Edg| Non |
+ | IRQ 42 | PCIX0 MSI level 3 | High |Lvl Edg| Non |
+ | IRQ 43 | L2 Cache | Risin | Edge | Non |
+ | IRQ 44 | GPT Compare Timer 0 | Risin | Edge | Non |
+ | IRQ 45 | GPT Compare Timer 1 | Risin | Edge | Non |
+ | IRQ 46 | GPT Compare Timer 2 | Risin | Edge | Non |
+ | IRQ 47 | GPT Compare Timer 3 | Risin | Edge | Non |
+ | IRQ 48 | GPT Compare Timer 4 | Risin | Edge | Non |
+ | IRQ 49 | Ext. IRQ 12 - PCI-X |pgm/Fal|pgm/Lvl| Non |
+ | IRQ 50 | Ext. IRQ 11 - |pgm (H)|pgm/Lvl| Non |
+ | IRQ 51 | Ext. IRQ 10 - |pgm (H)|pgm/Lvl| Non |
+ | IRQ 52 | Ext. IRQ 9 |pgm (H)|pgm/Lvl| Non |
+ | IRQ 53 | Ext. IRQ 8 |pgm (H)|pgm/Lvl| Non |
+ | IRQ 54 | DMA Error | High | Level | Non |
+ | IRQ 55 | DMA I2O Error | High | Level | Non |
+ | IRQ 56 | Serial ROM | High | Level | Non |
+ | IRQ 57 | PCIX0 Error | High | Edge | Non |
+ | IRQ 58 | Ext. IRQ 7- |pgm (H)|pgm/Lvl| Non |
+ | IRQ 59 | Ext. IRQ 6- |pgm (H)|pgm/Lvl| Non |
+ | IRQ 60 | EMAC0 Interrupt | High | Level | Non |
+ | IRQ 61 | EMAC0 Wake-up | High | Level | Non |
+ | IRQ 62 | Reserved | High | Level | Non |
+ | IRQ 63 | XOR | High | Level | Non |
+ |----------------------------------------------------------------------
+ | IRQ 64 | PE0 AL | High | Level | Non |
+ | IRQ 65 | PE0 VPD Access | Risin | Edge | Non |
+ | IRQ 66 | PE0 Hot Reset Request | Risin | Edge | Non |
+ | IRQ 67 | PE0 Hot Reset Request | Falli | Edge | Non |
+ | IRQ 68 | PE0 TCR | High | Level | Non |
+ | IRQ 69 | PE0 BusMaster VCO | Falli | Edge | Non |
+ | IRQ 70 | PE0 DCR Error | High | Level | Non |
+ | IRQ 71 | Reserved | N/A | N/A | Non |
+ | IRQ 72 | PE1 AL | High | Level | Non |
+ | IRQ 73 | PE1 VPD Access | Risin | Edge | Non |
+ | IRQ 74 | PE1 Hot Reset Request | Risin | Edge | Non |
+ | IRQ 75 | PE1 Hot Reset Request | Falli | Edge | Non |
+ | IRQ 76 | PE1 TCR | High | Level | Non |
+ | IRQ 77 | PE1 BusMaster VCO | Falli | Edge | Non |
+ | IRQ 78 | PE1 DCR Error | High | Level | Non |
+ | IRQ 79 | Reserved | N/A | N/A | Non |
+ | IRQ 80 | PE2 AL | High | Level | Non |
+ | IRQ 81 | PE2 VPD Access | Risin | Edge | Non |
+ | IRQ 82 | PE2 Hot Reset Request | Risin | Edge | Non |
+ | IRQ 83 | PE2 Hot Reset Request | Falli | Edge | Non |
+ | IRQ 84 | PE2 TCR | High | Level | Non |
+ | IRQ 85 | PE2 BusMaster VCO | Falli | Edge | Non |
+ | IRQ 86 | PE2 DCR Error | High | Level | Non |
+ | IRQ 87 | Reserved | N/A | N/A | Non |
+ | IRQ 88 | External IRQ(5) | Progr | Progr | Non |
+ | IRQ 89 | External IRQ 4 - Ethernet | Progr | Progr | Non |
+ | IRQ 90 | External IRQ 3 - PCI-X | Progr | Progr | Non |
+ | IRQ 91 | External IRQ 2 - PCI-X | Progr | Progr | Non |
+ | IRQ 92 | External IRQ 1 - PCI-X | Progr | Progr | Non |
+ | IRQ 93 | External IRQ 0 - PCI-X | Progr | Progr | Non |
+ | IRQ 94 | Reserved | N/A | N/A | Non |
+ | IRQ 95 | Reserved | N/A | N/A | Non |
+ |---------------------------------------------------------------------
+ | IRQ 96 | PE0 INTA | High | Level | Non |
+ | IRQ 97 | PE0 INTB | High | Level | Non |
+ | IRQ 98 | PE0 INTC | High | Level | Non |
+ | IRQ 99 | PE0 INTD | High | Level | Non |
+ | IRQ 100 | PE1 INTA | High | Level | Non |
+ | IRQ 101 | PE1 INTB | High | Level | Non |
+ | IRQ 102 | PE1 INTC | High | Level | Non |
+ | IRQ 103 | PE1 INTD | High | Level | Non |
+ | IRQ 104 | PE2 INTA | High | Level | Non |
+ | IRQ 105 | PE2 INTB | High | Level | Non |
+ | IRQ 106 | PE2 INTC | High | Level | Non |
+ | IRQ 107 | PE2 INTD | Risin | Edge | Non |
+ | IRQ 108 | PCI Express MSI Level 4 | Risin | Edge | Non |
+ | IRQ 109 | PCI Express MSI Level 5 | Risin | Edge | Non |
+ | IRQ 110 | PCI Express MSI Level 6 | Risin | Edge | Non |
+ | IRQ 111 | PCI Express MSI Level 7 | Risin | Edge | Non |
+ | IRQ 116 | PCI Express MSI Level 12 | Risin | Edge | Non |
+ | IRQ 112 | PCI Express MSI Level 8 | Risin | Edge | Non |
+ | IRQ 113 | PCI Express MSI Level 9 | Risin | Edge | Non |
+ | IRQ 114 | PCI Express MSI Level 10 | Risin | Edge | Non |
+ | IRQ 115 | PCI Express MSI Level 11 | Risin | Edge | Non |
+ | IRQ 117 | PCI Express MSI Level 13 | Risin | Edge | Non |
+ | IRQ 118 | PCI Express MSI Level 14 | Risin | Edge | Non |
+ | IRQ 119 | PCI Express MSI Level 15 | Risin | Edge | Non |
+ | IRQ 120 | PCI Express MSI Level 16 | Risin | Edge | Non |
+ | IRQ 121 | PCI Express MSI Level 17 | Risin | Edge | Non |
+ | IRQ 122 | PCI Express MSI Level 18 | Risin | Edge | Non |
+ | IRQ 123 | PCI Express MSI Level 19 | Risin | Edge | Non |
+ | IRQ 124 | PCI Express MSI Level 20 | Risin | Edge | Non |
+ | IRQ 125 | PCI Express MSI Level 21 | Risin | Edge | Non |
+ | IRQ 126 | PCI Express MSI Level 22 | Risin | Edge | Non |
+ | IRQ 127 | PCI Express MSI Level 23 | Risin | Edge | Non |
+ +---------+-----------------------------------+-------+-------+------*/
+ /*--------------------------------------------------------------------+
+ | Put UICs in PowerPC440SPemode.
+ | Initialise UIC registers. Clear all interrupts. Disable all
+ | interrupts.
+ | Set critical interrupt values. Set interrupt polarities. Set
+ | interrupt trigger levels. Make bit 0 High priority. Clear all
+ | interrupts again.
+ +-------------------------------------------------------------------*/
+ mtdcr (uic3sr, 0xffffffff); /* Clear all interrupts */
+ mtdcr (uic3er, 0x00000000); /* disable all interrupts */
+ mtdcr (uic3cr, 0x00000000); /* Set Critical / Non Critical
+ * interrupts */
+ mtdcr (uic3pr, 0xffffffff); /* Set Interrupt Polarities */
+ mtdcr (uic3tr, 0x001fffff); /* Set Interrupt Trigger Levels */
+ mtdcr (uic3vr, 0x00000001); /* Set Vect base=0,INT31 Highest
+ * priority */
+ mtdcr (uic3sr, 0x00000000); /* clear all interrupts */
+ mtdcr (uic3sr, 0xffffffff); /* clear all interrupts */
+
+ mtdcr (uic2sr, 0xffffffff); /* Clear all interrupts */
+ mtdcr (uic2er, 0x00000000); /* disable all interrupts */
+ mtdcr (uic2cr, 0x00000000); /* Set Critical / Non Critical
+ * interrupts */
+ mtdcr (uic2pr, 0xebebebff); /* Set Interrupt Polarities */
+ mtdcr (uic2tr, 0x74747400); /* Set Interrupt Trigger Levels */
+ mtdcr (uic2vr, 0x00000001); /* Set Vect base=0,INT31 Highest
+ * priority */
+ mtdcr (uic2sr, 0x00000000); /* clear all interrupts */
+ mtdcr (uic2sr, 0xffffffff); /* clear all interrupts */
+
+ mtdcr (uic1sr, 0xffffffff); /* Clear all interrupts */
+ mtdcr (uic1er, 0x00000000); /* disable all interrupts */
+ mtdcr (uic1cr, 0x00000000); /* Set Critical / Non Critical
+ * interrupts */
+ mtdcr (uic1pr, 0xffffffff); /* Set Interrupt Polarities */
+ mtdcr (uic1tr, 0x001f8040); /* Set Interrupt Trigger Levels */
+ mtdcr (uic1vr, 0x00000001); /* Set Vect base=0,INT31 Highest
+ * priority */
+ mtdcr (uic1sr, 0x00000000); /* clear all interrupts */
+ mtdcr (uic1sr, 0xffffffff); /* clear all interrupts */
+
+ mtdcr (uic0sr, 0xffffffff); /* Clear all interrupts */
+ mtdcr (uic0er, 0x00000000); /* disable all interrupts excepted
+ * cascade to be checked */
+ mtdcr (uic0cr, 0x00104001); /* Set Critical / Non Critical
+ * interrupts */
+ mtdcr (uic0pr, 0xffffffff); /* Set Interrupt Polarities */
+ mtdcr (uic0tr, 0x010f0004); /* Set Interrupt Trigger Levels */
+ mtdcr (uic0vr, 0x00000001); /* Set Vect base=0,INT31 Highest
+ * priority */
+ mtdcr (uic0sr, 0x00000000); /* clear all interrupts */
+ mtdcr (uic0sr, 0xffffffff); /* clear all interrupts */
+
+ /* SDR0_MFR should be part of Ethernet init */
+ mfsdr (sdr_mfr, mfr);
+ mfr &= ~SDR0_MFR_ECS_MASK;
+ /*mtsdr(sdr_mfr, mfr);*/
+ fpga_init();
+
+ return 0;
+}
+
+int checkboard (void)
+{
+ char *s = getenv("serial#");
+
+ printf("Board: Yucca - AMCC 440SPe Evaluation Board");
+ if (s != NULL) {
+ puts(", serial# ");
+ puts(s);
+ }
+ putc('\n');
+
+ return 0;
+}
+
+static long int yucca_probe_for_dimms(void)
+{
+ long int dimm_installed[MAXDIMMS];
+ long int dimm_num, probe_result;
+ long int dimms_found = 0;
+ uchar dimm_addr = IIC0_DIMM0_ADDR;
+
+ for (dimm_num = 0; dimm_num < MAXDIMMS; dimm_num++) {
+ /* check if there is a chip at the dimm address */
+ switch (dimm_num) {
+ case 0:
+ dimm_addr = IIC0_DIMM0_ADDR;
+ break;
+ case 1:
+ dimm_addr = IIC0_DIMM1_ADDR;
+ break;
+ }
+ probe_result = i2c_probe(dimm_addr);
+
+ if (probe_result == 0) {
+ dimm_installed[dimm_num] = TRUE;
+ dimms_found++;
+ debug("DIMM slot %d: DDR2 SDRAM detected\n",dimm_num);
+ } else {
+ dimm_installed[dimm_num] = FALSE;
+ debug("DIMM slot %d: Not populated or cannot sucessfully probe the DIMM\n", dimm_num);
+ }
+ }
+
+ if (dimms_found == 0) {
+ printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n");
+ hang();
+ }
+
+ if (dimm_installed[0] != TRUE) {
+ printf("\nERROR - DIMM slot 0 must be populated before DIMM slot 1.\n");
+ printf(" Unsupported configuration. Move DIMM module from DIMM slot 1 to slot 0.\n\n");
+ hang();
+ }
+
+ return dimms_found;
+}
+
+/*************************************************************************
+ * init SDRAM controller with fixed value
+ * the initialization values are for 2x MICRON DDR2
+ * PN: MT18HTF6472DY-53EB2
+ * 512MB, DDR2, 533, CL4, ECC, REG
+ ************************************************************************/
+static long int fixed_sdram(void)
+{
+ long int yucca_dimms = 0;
+
+ yucca_dimms = yucca_probe_for_dimms();
+
+ /* SDRAM0_MCOPT2 (0X21) Clear DCEN BIT */
+ mtdcr( 0x10, 0x00000021 );
+ mtdcr( 0x11, 0x84000000 );
+
+ /* SDRAM0_MCOPT1 (0X20) ECC OFF / 64 bits / 4 banks / DDR2 */
+ mtdcr( 0x10, 0x00000020 );
+ mtdcr( 0x11, 0x2D122000 );
+
+ /* SET MCIF0_CODT Die Termination On */
+ mtdcr( 0x10, 0x00000026 );
+ if (yucca_dimms == 2)
+ mtdcr( 0x11, 0x2A800021 );
+ else if (yucca_dimms == 1)
+ mtdcr( 0x11, 0x02800021 );
+
+ /* On-Die Termination for Bank 0 */
+ mtdcr( 0x10, 0x00000022 );
+ if (yucca_dimms == 2)
+ mtdcr( 0x11, 0x18000000 );
+ else if (yucca_dimms == 1)
+ mtdcr( 0x11, 0x06000000 );
+
+ /* On-Die Termination for Bank 1 */
+ mtdcr( 0x10, 0x00000023 );
+ if (yucca_dimms == 2)
+ mtdcr( 0x11, 0x18000000 );
+ else if (yucca_dimms == 1)
+ mtdcr( 0x11, 0x01800000 );
+
+ /* On-Die Termination for Bank 2 */
+ mtdcr( 0x10, 0x00000024 );
+ if (yucca_dimms == 2)
+ mtdcr( 0x11, 0x01800000 );
+ else if (yucca_dimms == 1)
+ mtdcr( 0x11, 0x00000000 );
+
+ /* On-Die Termination for Bank 3 */
+ mtdcr( 0x10, 0x00000025 );
+ if (yucca_dimms == 2)
+ mtdcr( 0x11, 0x01800000 );
+ else if (yucca_dimms == 1)
+ mtdcr( 0x11, 0x00000000 );
+
+ /* Refresh Time register (0x30) Refresh every 7.8125uS */
+ mtdcr( 0x10, 0x00000030 );
+ mtdcr( 0x11, 0x08200000 );
+
+ /* SET MCIF0_MMODE CL 4 */
+ mtdcr( 0x10, 0x00000088 );
+ mtdcr( 0x11, 0x00000642 );
+
+ /* MCIF0_MEMODE */
+ mtdcr( 0x10, 0x00000089 );
+ mtdcr( 0x11, 0x00000004 );
+
+ /*SET MCIF0_MB0CF */
+ mtdcr( 0x10, 0x00000040 );
+ mtdcr( 0x11, 0x00000201 );
+
+ /* SET MCIF0_MB1CF */
+ mtdcr( 0x10, 0x00000044 );
+ mtdcr( 0x11, 0x00000201 );
+
+ /* SET MCIF0_MB2CF */
+ mtdcr( 0x10, 0x00000048 );
+ if (yucca_dimms == 2)
+ mtdcr( 0x11, 0x00000201 );
+ else if (yucca_dimms == 1)
+ mtdcr( 0x11, 0x00000000 );
+
+ /* SET MCIF0_MB3CF */
+ mtdcr( 0x10, 0x0000004c );
+ if (yucca_dimms == 2)
+ mtdcr( 0x11, 0x00000201 );
+ else if (yucca_dimms == 1)
+ mtdcr( 0x11, 0x00000000 );
+
+ /* SET MCIF0_INITPLR0 # NOP */
+ mtdcr( 0x10, 0x00000050 );
+ mtdcr( 0x11, 0xB5380000 );
+
+ /* SET MCIF0_INITPLR1 # PRE */
+ mtdcr( 0x10, 0x00000051 );
+ mtdcr( 0x11, 0x82100400 );
+
+ /* SET MCIF0_INITPLR2 # EMR2 */
+ mtdcr( 0x10, 0x00000052 );
+ mtdcr( 0x11, 0x80820000 );
+
+ /* SET MCIF0_INITPLR3 # EMR3 */
+ mtdcr( 0x10, 0x00000053 );
+ mtdcr( 0x11, 0x80830000 );
+
+ /* SET MCIF0_INITPLR4 # EMR DLL ENABLE */
+ mtdcr( 0x10, 0x00000054 );
+ mtdcr( 0x11, 0x80810000 );
+
+ /* SET MCIF0_INITPLR5 # MR DLL RESET */
+ mtdcr( 0x10, 0x00000055 );
+ mtdcr( 0x11, 0x80800542 );
+
+ /* SET MCIF0_INITPLR6 # PRE */
+ mtdcr( 0x10, 0x00000056 );
+ mtdcr( 0x11, 0x82100400 );
+
+ /* SET MCIF0_INITPLR7 # Refresh */
+ mtdcr( 0x10, 0x00000057 );
+ mtdcr( 0x11, 0x8A080000 );
+
+ /* SET MCIF0_INITPLR8 # Refresh */
+ mtdcr( 0x10, 0x00000058 );
+ mtdcr( 0x11, 0x8A080000 );
+
+ /* SET MCIF0_INITPLR9 # Refresh */
+ mtdcr( 0x10, 0x00000059 );
+ mtdcr( 0x11, 0x8A080000 );
+
+ /* SET MCIF0_INITPLR10 # Refresh */
+ mtdcr( 0x10, 0x0000005A );
+ mtdcr( 0x11, 0x8A080000 );
+
+ /* SET MCIF0_INITPLR11 # MR */
+ mtdcr( 0x10, 0x0000005B );
+ mtdcr( 0x11, 0x80800442 );
+
+ /* SET MCIF0_INITPLR12 # EMR OCD Default*/
+ mtdcr( 0x10, 0x0000005C );
+ mtdcr( 0x11, 0x80810380 );
+
+ /* SET MCIF0_INITPLR13 # EMR OCD Exit */
+ mtdcr( 0x10, 0x0000005D );
+ mtdcr( 0x11, 0x80810000 );
+
+ /* 0x80: Adv Addr clock by 180 deg */
+ mtdcr( 0x10, 0x00000080 );
+ mtdcr( 0x11, 0x80000000 );
+
+ /* 0x21: Exit self refresh, set DC_EN */
+ mtdcr( 0x10, 0x00000021 );
+ mtdcr( 0x11, 0x28000000 );
+
+ /* 0x81: Write DQS Adv 90 + Fractional DQS Delay */
+ mtdcr( 0x10, 0x00000081 );
+ mtdcr( 0x11, 0x80000800 );
+
+ /* MCIF0_SDTR1 */
+ mtdcr( 0x10, 0x00000085 );
+ mtdcr( 0x11, 0x80201000 );
+
+ /* MCIF0_SDTR2 */
+ mtdcr( 0x10, 0x00000086 );
+ mtdcr( 0x11, 0x42103242 );
+
+ /* MCIF0_SDTR3 */
+ mtdcr( 0x10, 0x00000087 );
+ mtdcr( 0x11, 0x0C100D14 );
+
+ /* SET MQ0_B0BAS base addr 00000000 / 256MB */
+ mtdcr( 0x40, 0x0000F800 );
+
+ /* SET MQ0_B1BAS base addr 10000000 / 256MB */
+ mtdcr( 0x41, 0x0400F800 );
+
+ /* SET MQ0_B2BAS base addr 20000000 / 256MB */
+ if (yucca_dimms == 2)
+ mtdcr( 0x42, 0x0800F800 );
+ else if (yucca_dimms == 1)
+ mtdcr( 0x42, 0x00000000 );
+
+ /* SET MQ0_B3BAS base addr 30000000 / 256MB */
+ if (yucca_dimms == 2)
+ mtdcr( 0x43, 0x0C00F800 );
+ else if (yucca_dimms == 1)
+ mtdcr( 0x43, 0x00000000 );
+
+ /* SDRAM_RQDC */
+ mtdcr( 0x10, 0x00000070 );
+ mtdcr( 0x11, 0x8000003F );
+
+ /* SDRAM_RDCC */
+ mtdcr( 0x10, 0x00000078 );
+ mtdcr( 0x11, 0x80000000 );
+
+ /* SDRAM_RFDC */
+ mtdcr( 0x10, 0x00000074 );
+ mtdcr( 0x11, 0x00000220 );
+
+ return (yucca_dimms * 512) << 20;
+}
+
+long int initdram (int board_type)
+{
+ long dram_size = 0;
+
+ dram_size = fixed_sdram();
+
+ return dram_size;
+}
+
+#if defined(CFG_DRAM_TEST)
+int testdram (void)
+{
+ uint *pstart = (uint *) 0x00000000;
+ uint *pend = (uint *) 0x08000000;
+ uint *p;
+
+ for (p = pstart; p < pend; p++)
+ *p = 0xaaaaaaaa;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0xaaaaaaaa) {
+ printf ("SDRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ for (p = pstart; p < pend; p++)
+ *p = 0x55555555;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0x55555555) {
+ printf ("SDRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+ return 0;
+}
+#endif
+
+/*************************************************************************
+ * pci_pre_init
+ *
+ * This routine is called just prior to registering the hose and gives
+ * the board the opportunity to check things. Returning a value of zero
+ * indicates that things are bad & PCI initialization should be aborted.
+ *
+ * Different boards may wish to customize the pci controller structure
+ * (add regions, override default access routines, etc) or perform
+ * certain pre-initialization actions.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+int pci_pre_init(struct pci_controller * hose )
+{
+ unsigned long strap;
+
+ /*-------------------------------------------------------------------+
+ * The yucca board is always configured as the host & requires the
+ * PCI arbiter to be enabled.
+ *-------------------------------------------------------------------*/
+ mfsdr(sdr_sdstp1, strap);
+ if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
+ printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
+ return 0;
+ }
+
+ return 1;
+}
+#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+
+/*************************************************************************
+ * pci_target_init
+ *
+ * The bootstrap configuration provides default settings for the pci
+ * inbound map (PIM). But the bootstrap config choices are limited and
+ * may not be sufficient for a given board.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller * hose )
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ /*-------------------------------------------------------------------+
+ * Disable everything
+ *-------------------------------------------------------------------*/
+ out32r( PCIX0_PIM0SA, 0 ); /* disable */
+ out32r( PCIX0_PIM1SA, 0 ); /* disable */
+ out32r( PCIX0_PIM2SA, 0 ); /* disable */
+ out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+
+ /*-------------------------------------------------------------------+
+ * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
+ * strapping options to not support sizes such as 128/256 MB.
+ *-------------------------------------------------------------------*/
+ out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
+ out32r( PCIX0_PIM0LAH, 0 );
+ out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+ out32r( PCIX0_BAR0, 0 );
+
+ /*-------------------------------------------------------------------+
+ * Program the board's subsystem id/vendor id
+ *-------------------------------------------------------------------*/
+ out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
+ out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
+
+ out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+}
+#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+
+#if defined(CONFIG_PCI)
+/*************************************************************************
+ * is_pci_host
+ *
+ * This routine is called to determine if a pci scan should be
+ * performed. With various hardware environments (especially cPCI and
+ * PPMC) it's insufficient to depend on the state of the arbiter enable
+ * bit in the strap register, or generic host/adapter assumptions.
+ *
+ * Rather than hard-code a bad assumption in the general 440 code, the
+ * 440 pci code requires the board to decide at runtime.
+ *
+ * Return 0 for adapter mode, non-zero for host (monarch) mode.
+ *
+ *
+ ************************************************************************/
+int is_pci_host(struct pci_controller *hose)
+{
+ /* The yucca board is always configured as host. */
+ return 1;
+}
+
+
+int yucca_pcie_card_present(int port)
+{
+ u16 reg;
+
+ reg = in_be16((u16 *)FPGA_REG1C);
+ switch(port) {
+ case 0:
+ return !(reg & FPGA_REG1C_PE0_PRSNT);
+ case 1:
+ return !(reg & FPGA_REG1C_PE1_PRSNT);
+ case 2:
+ return !(reg & FPGA_REG1C_PE2_PRSNT);
+ default:
+ return 0;
+ }
+}
+
+/*
+ * For the given slot, set rootpoint mode, send power to the slot,
+ * turn on the green LED and turn off the yellow LED, enable the clock
+ * and turn off reset.
+ */
+void yucca_setup_pcie_fpga_rootpoint(int port)
+{
+ u16 power, clock, green_led, yellow_led, reset_off, rootpoint, endpoint;
+
+ switch(port) {
+ case 0:
+ rootpoint = FPGA_REG1C_PE0_ROOTPOINT;
+ endpoint = 0;
+ power = FPGA_REG1A_PE0_PWRON;
+ green_led = FPGA_REG1A_PE0_GLED;
+ clock = FPGA_REG1A_PE0_REFCLK_ENABLE;
+ yellow_led = FPGA_REG1A_PE0_YLED;
+ reset_off = FPGA_REG1C_PE0_PERST;
+ break;
+ case 1:
+ rootpoint = 0;
+ endpoint = FPGA_REG1C_PE1_ENDPOINT;
+ power = FPGA_REG1A_PE1_PWRON;
+ green_led = FPGA_REG1A_PE1_GLED;
+ clock = FPGA_REG1A_PE1_REFCLK_ENABLE;
+ yellow_led = FPGA_REG1A_PE1_YLED;
+ reset_off = FPGA_REG1C_PE1_PERST;
+ break;
+ case 2:
+ rootpoint = 0;
+ endpoint = FPGA_REG1C_PE2_ENDPOINT;
+ power = FPGA_REG1A_PE2_PWRON;
+ green_led = FPGA_REG1A_PE2_GLED;
+ clock = FPGA_REG1A_PE2_REFCLK_ENABLE;
+ yellow_led = FPGA_REG1A_PE2_YLED;
+ reset_off = FPGA_REG1C_PE2_PERST;
+ break;
+
+ default:
+ return;
+ }
+
+ out_be16((u16 *)FPGA_REG1A,
+ ~(power | clock | green_led) &
+ (yellow_led | in_be16((u16 *)FPGA_REG1A)));
+
+ out_be16((u16 *)FPGA_REG1C,
+ ~(endpoint | reset_off) &
+ (rootpoint | in_be16((u16 *)FPGA_REG1C)));
+ /*
+ * Leave device in reset for a while after powering on the
+ * slot to give it a chance to initialize.
+ */
+ udelay(250 * 1000);
+
+ out_be16((u16 *)FPGA_REG1C, reset_off | in_be16((u16 *)FPGA_REG1C));
+}
+
+
+static struct pci_controller pcie_hose[3] = {{0},{0},{0}};
+
+void pcie_setup_hoses(void)
+{
+ struct pci_controller *hose;
+ int i, bus;
+
+ /*
+ * assume we're called after the PCIX hose is initialized, which takes
+ * bus ID 0 and therefore start numbering PCIe's from 1.
+ */
+ bus = 1;
+ for (i = 0; i <= 2; i++) {
+ /* Check for yucca card presence */
+ if (!yucca_pcie_card_present(i))
+ continue;
+
+ yucca_setup_pcie_fpga_rootpoint(i);
+
+ if (ppc440spe_init_pcie_rootport(i)) {
+ printf("PCIE%d: initialization failed\n", i);
+ continue;
+ }
+
+ hose = &pcie_hose[i];
+ hose->first_busno = bus;
+ hose->last_busno = bus;
+ bus++;
+
+ /* setup mem resource */
+ pci_set_region(hose->regions + 0,
+ CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+ CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+ CFG_PCIE_MEMSIZE,
+ PCI_REGION_MEM
+ );
+ hose->region_count = 1;
+ pci_register_hose(hose);
+
+ ppc440spe_setup_pcie(hose, i);
+ hose->last_busno = pci_hose_scan(hose);
+ }
+}
+#endif /* defined(CONFIG_PCI) */
+
+int misc_init_f (void)
+{
+ uint reg;
+#if defined(CONFIG_STRESS)
+ uint i ;
+ uint disp;
+#endif
+
+ out16(FPGA_REG10, (in16(FPGA_REG10) &
+ ~(FPGA_REG10_AUTO_NEG_DIS|FPGA_REG10_RESET_ETH)) |
+ FPGA_REG10_10MHZ_ENABLE |
+ FPGA_REG10_100MHZ_ENABLE |
+ FPGA_REG10_GIGABIT_ENABLE |
+ FPGA_REG10_FULL_DUPLEX );
+
+ udelay(10000); /* wait 10ms */
+
+ out16(FPGA_REG10, (in16(FPGA_REG10) | FPGA_REG10_RESET_ETH));
+
+ /* minimal init for PCIe */
+ /* pci express 0 Endpoint Mode */
+ mfsdr(SDR0_PE0DLPSET, reg);
+ reg &= (~0x00400000);
+ mtsdr(SDR0_PE0DLPSET, reg);
+ /* pci express 1 Rootpoint Mode */
+ mfsdr(SDR0_PE1DLPSET, reg);
+ reg |= 0x00400000;
+ mtsdr(SDR0_PE1DLPSET, reg);
+ /* pci express 2 Rootpoint Mode */
+ mfsdr(SDR0_PE2DLPSET, reg);
+ reg |= 0x00400000;
+ mtsdr(SDR0_PE2DLPSET, reg);
+
+ out16(FPGA_REG1C,(in16 (FPGA_REG1C) &
+ ~FPGA_REG1C_PE0_ROOTPOINT &
+ ~FPGA_REG1C_PE1_ENDPOINT &
+ ~FPGA_REG1C_PE2_ENDPOINT));
+
+#if defined(CONFIG_STRESS)
+ /*
+ * all this setting done by linux only needed by stress an charac. test
+ * procedure
+ * PCIe 1 Rootpoint PCIe2 Endpoint
+ * PCIe 0 FIR Pre-emphasis Filter Coefficients & Transmit Driver
+ * Power Level
+ */
+ for (i = 0, disp = 0; i < 8; i++, disp += 3) {
+ mfsdr(SDR0_PE0HSSSET1L0 + disp, reg);
+ reg |= 0x33000000;
+ mtsdr(SDR0_PE0HSSSET1L0 + disp, reg);
+ }
+
+ /*
+ * PCIe 1 FIR Pre-emphasis Filter Coefficients & Transmit Driver
+ * Power Level
+ */
+ for (i = 0, disp = 0; i < 4; i++, disp += 3) {
+ mfsdr(SDR0_PE1HSSSET1L0 + disp, reg);
+ reg |= 0x33000000;
+ mtsdr(SDR0_PE1HSSSET1L0 + disp, reg);
+ }
+
+ /*
+ * PCIE 2 FIR Pre-emphasis Filter Coefficients & Transmit Driver
+ * Power Level
+ */
+ for (i = 0, disp = 0; i < 4; i++, disp += 3) {
+ mfsdr(SDR0_PE2HSSSET1L0 + disp, reg);
+ reg |= 0x33000000;
+ mtsdr(SDR0_PE2HSSSET1L0 + disp, reg);
+ }
+
+ reg = 0x21242222;
+ mtsdr(SDR0_PE2UTLSET1, reg);
+ reg = 0x11000000;
+ mtsdr(SDR0_PE2UTLSET2, reg);
+ /* pci express 1 Endpoint Mode */
+ reg = 0x00004000;
+ mtsdr(SDR0_PE2DLPSET, reg);
+
+ mtsdr(SDR0_UART1, 0x2080005a); /* patch for TG */
+#endif
+ return 0;
+}
+
+void fpga_init(void)
+{
+ /*
+ * by default sdram access is disabled by fpga
+ */
+ out16(FPGA_REG10, (in16 (FPGA_REG10) |
+ FPGA_REG10_SDRAM_ENABLE |
+ FPGA_REG10_ENABLE_DISPLAY ));
+
+ return;
+}
+
+#ifdef CONFIG_POST
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+ return (ctrlc());
+}
+#endif
+
+/*---------------------------------------------------------------------------+
+ | onboard_pci_arbiter_selected => from EPLD
+ +---------------------------------------------------------------------------*/
+int onboard_pci_arbiter_selected(int core_pci)
+{
+#if 0
+ unsigned long onboard_pci_arbiter_sel;
+
+ onboard_pci_arbiter_sel = in16(FPGA_REG0) & FPGA_REG0_EXT_ARB_SEL_MASK;
+
+ if (onboard_pci_arbiter_sel == FPGA_REG0_EXT_ARB_SEL_EXTERNAL)
+ return (BOARD_OPTION_SELECTED);
+ else
+#endif
+ return (BOARD_OPTION_NOT_SELECTED);
+}
+
+/*---------------------------------------------------------------------------+
+ | ppcMfcpr.
+ +---------------------------------------------------------------------------*/
+unsigned long ppcMfcpr(unsigned long cpr_reg)
+{
+ unsigned long msr;
+ unsigned long cpr_cfgaddr_temp;
+ unsigned long cpr_value;
+
+ msr = (mfmsr () & ~(MSR_EE));
+ cpr_cfgaddr_temp = mfdcr(CPR0_CFGADDR);
+ mtdcr(CPR0_CFGADDR, cpr_reg);
+ cpr_value = mfdcr(CPR0_CFGDATA);
+ mtdcr(CPR0_CFGADDR, cpr_cfgaddr_temp);
+ mtmsr(msr);
+
+ return (cpr_value);
+}
+
+/*----------------------------------------------------------------------------+
+| Indirect Access of the System DCR's (SDR)
+| ppcMfsdr
++----------------------------------------------------------------------------*/
+unsigned long ppcMfsdr(unsigned long sdr_reg)
+{
+ unsigned long msr;
+ unsigned long sdr_cfgaddr_temp;
+ unsigned long sdr_value;
+
+ msr = (mfmsr () & ~(MSR_EE));
+ sdr_cfgaddr_temp = mfdcr(SDR0_CFGADDR);
+ mtdcr(SDR0_CFGADDR, sdr_reg);
+ sdr_value = mfdcr(SDR0_CFGDATA);
+ mtdcr(SDR0_CFGADDR, sdr_cfgaddr_temp);
+ mtmsr(msr);
+
+ return (sdr_value);
+}
diff --git a/board/amcc/yucca/yucca.h b/board/amcc/yucca/yucca.h
new file mode 100644
index 0000000..66f7584
--- /dev/null
+++ b/board/amcc/yucca/yucca.h
@@ -0,0 +1,363 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __YUCCA_H_
+#define __YUCCA_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/*----------------------------------------------------------------------------+
+| Defines
++----------------------------------------------------------------------------*/
+
+#define TMR_FREQ_EXT 25000000
+#define BOARD_UART_CLOCK 11059200
+
+#define BOARD_OPTION_SELECTED 1
+#define BOARD_OPTION_NOT_SELECTED 0
+
+#define ENGINEERING_CLOCK_CHECKING "clk_chk"
+#define ENGINEERING_EXTERNAL_CLOCK "ext_clk"
+
+#define ENGINEERING_CLOCK_CHECKING_DATA 1
+#define ENGINEERING_EXTERNAL_CLOCK_DATA 2
+
+/* ethernet definition */
+#define MAX_ENETMODE_PARM 3
+#define ENETMODE_NEG 0
+#define ENETMODE_SPEED 1
+#define ENETMODE_DUPLEX 2
+
+#define ENETMODE_AUTONEG 0
+#define ENETMODE_NO_AUTONEG 1
+#define ENETMODE_10 2
+#define ENETMODE_100 3
+#define ENETMODE_1000 4
+#define ENETMODE_HALF 5
+#define ENETMODE_FULL 6
+
+#define NUM_TLB_ENTRIES 64
+
+/*----------------------------------------------------------------------------+
+| TLB specific defines.
++----------------------------------------------------------------------------*/
+#define TLB_256MB_ALIGN_MASK 0xF0000000
+#define TLB_16MB_ALIGN_MASK 0xFF000000
+#define TLB_1MB_ALIGN_MASK 0xFFF00000
+#define TLB_256KB_ALIGN_MASK 0xFFFC0000
+#define TLB_64KB_ALIGN_MASK 0xFFFF0000
+#define TLB_16KB_ALIGN_MASK 0xFFFFC000
+#define TLB_4KB_ALIGN_MASK 0xFFFFF000
+#define TLB_1KB_ALIGN_MASK 0xFFFFFC00
+#define TLB_256MB_SIZE 0x10000000
+#define TLB_16MB_SIZE 0x01000000
+#define TLB_1MB_SIZE 0x00100000
+#define TLB_256KB_SIZE 0x00040000
+#define TLB_64KB_SIZE 0x00010000
+#define TLB_16KB_SIZE 0x00004000
+#define TLB_4KB_SIZE 0x00001000
+#define TLB_1KB_SIZE 0x00000400
+
+#define TLB_WORD0_EPN_MASK 0xFFFFFC00
+#define TLB_WORD0_EPN_ENCODE(n) (((unsigned long)(n))&0xFFFFFC00)
+#define TLB_WORD0_EPN_DECODE(n) (((unsigned long)(n))&0xFFFFFC00)
+#define TLB_WORD0_V_MASK 0x00000200
+#define TLB_WORD0_V_ENABLE 0x00000200
+#define TLB_WORD0_V_DISABLE 0x00000000
+#define TLB_WORD0_TS_MASK 0x00000100
+#define TLB_WORD0_TS_1 0x00000100
+#define TLB_WORD0_TS_0 0x00000000
+#define TLB_WORD0_SIZE_MASK 0x000000F0
+#define TLB_WORD0_SIZE_1KB 0x00000000
+#define TLB_WORD0_SIZE_4KB 0x00000010
+#define TLB_WORD0_SIZE_16KB 0x00000020
+#define TLB_WORD0_SIZE_64KB 0x00000030
+#define TLB_WORD0_SIZE_256KB 0x00000040
+#define TLB_WORD0_SIZE_1MB 0x00000050
+#define TLB_WORD0_SIZE_16MB 0x00000070
+#define TLB_WORD0_SIZE_256MB 0x00000090
+#define TLB_WORD0_TPAR_MASK 0x0000000F
+#define TLB_WORD0_TPAR_ENCODE(n) ((((unsigned long)(n))&0x0F)<<0)
+#define TLB_WORD0_TPAR_DECODE(n) ((((unsigned long)(n))>>0)&0x0F)
+
+#define TLB_WORD1_RPN_MASK 0xFFFFFC00
+#define TLB_WORD1_RPN_ENCODE(n) (((unsigned long)(n))&0xFFFFFC00)
+#define TLB_WORD1_RPN_DECODE(n) (((unsigned long)(n))&0xFFFFFC00)
+#define TLB_WORD1_PAR1_MASK 0x00000300
+#define TLB_WORD1_PAR1_ENCODE(n) ((((unsigned long)(n))&0x03)<<8)
+#define TLB_WORD1_PAR1_DECODE(n) ((((unsigned long)(n))>>8)&0x03)
+#define TLB_WORD1_PAR1_0 0x00000000
+#define TLB_WORD1_PAR1_1 0x00000100
+#define TLB_WORD1_PAR1_2 0x00000200
+#define TLB_WORD1_PAR1_3 0x00000300
+#define TLB_WORD1_ERPN_MASK 0x0000000F
+#define TLB_WORD1_ERPN_ENCODE(n) ((((unsigned long)(n))&0x0F)<<0)
+#define TLB_WORD1_ERPN_DECODE(n) ((((unsigned long)(n))>>0)&0x0F)
+
+#define TLB_WORD2_PAR2_MASK 0xC0000000
+#define TLB_WORD2_PAR2_ENCODE(n) ((((unsigned long)(n))&0x03)<<30)
+#define TLB_WORD2_PAR2_DECODE(n) ((((unsigned long)(n))>>30)&0x03)
+#define TLB_WORD2_PAR2_0 0x00000000
+#define TLB_WORD2_PAR2_1 0x40000000
+#define TLB_WORD2_PAR2_2 0x80000000
+#define TLB_WORD2_PAR2_3 0xC0000000
+#define TLB_WORD2_U0_MASK 0x00008000
+#define TLB_WORD2_U0_ENABLE 0x00008000
+#define TLB_WORD2_U0_DISABLE 0x00000000
+#define TLB_WORD2_U1_MASK 0x00004000
+#define TLB_WORD2_U1_ENABLE 0x00004000
+#define TLB_WORD2_U1_DISABLE 0x00000000
+#define TLB_WORD2_U2_MASK 0x00002000
+#define TLB_WORD2_U2_ENABLE 0x00002000
+#define TLB_WORD2_U2_DISABLE 0x00000000
+#define TLB_WORD2_U3_MASK 0x00001000
+#define TLB_WORD2_U3_ENABLE 0x00001000
+#define TLB_WORD2_U3_DISABLE 0x00000000
+#define TLB_WORD2_W_MASK 0x00000800
+#define TLB_WORD2_W_ENABLE 0x00000800
+#define TLB_WORD2_W_DISABLE 0x00000000
+#define TLB_WORD2_I_MASK 0x00000400
+#define TLB_WORD2_I_ENABLE 0x00000400
+#define TLB_WORD2_I_DISABLE 0x00000000
+#define TLB_WORD2_M_MASK 0x00000200
+#define TLB_WORD2_M_ENABLE 0x00000200
+#define TLB_WORD2_M_DISABLE 0x00000000
+#define TLB_WORD2_G_MASK 0x00000100
+#define TLB_WORD2_G_ENABLE 0x00000100
+#define TLB_WORD2_G_DISABLE 0x00000000
+#define TLB_WORD2_E_MASK 0x00000080
+#define TLB_WORD2_E_ENABLE 0x00000080
+#define TLB_WORD2_E_DISABLE 0x00000000
+#define TLB_WORD2_UX_MASK 0x00000020
+#define TLB_WORD2_UX_ENABLE 0x00000020
+#define TLB_WORD2_UX_DISABLE 0x00000000
+#define TLB_WORD2_UW_MASK 0x00000010
+#define TLB_WORD2_UW_ENABLE 0x00000010
+#define TLB_WORD2_UW_DISABLE 0x00000000
+#define TLB_WORD2_UR_MASK 0x00000008
+#define TLB_WORD2_UR_ENABLE 0x00000008
+#define TLB_WORD2_UR_DISABLE 0x00000000
+#define TLB_WORD2_SX_MASK 0x00000004
+#define TLB_WORD2_SX_ENABLE 0x00000004
+#define TLB_WORD2_SX_DISABLE 0x00000000
+#define TLB_WORD2_SW_MASK 0x00000002
+#define TLB_WORD2_SW_ENABLE 0x00000002
+#define TLB_WORD2_SW_DISABLE 0x00000000
+#define TLB_WORD2_SR_MASK 0x00000001
+#define TLB_WORD2_SR_ENABLE 0x00000001
+#define TLB_WORD2_SR_DISABLE 0x00000000
+
+/*----------------------------------------------------------------------------+
+| Board specific defines.
++----------------------------------------------------------------------------*/
+#define NONCACHE_MEMORY_SIZE (64*1024)
+#define NONCACHE_AREA0_ENDOFFSET (64*1024)
+#define NONCACHE_AREA1_ENDOFFSET (32*1024)
+
+#define FLASH_SECTORSIZE 0x00010000
+
+/* SDRAM MICRON */
+#define SDRAM_MICRON 0x2C
+
+#define SDRAM_TRUE 1
+#define SDRAM_FALSE 0
+#define SDRAM_DDR1 1
+#define SDRAM_DDR2 2
+#define SDRAM_NONE 0
+#define MAXDIMMS 2 /* Changes le 12/01/05 pour 1.6 */
+#define MAXRANKS 4 /* Changes le 12/01/05 pour 1.6 */
+#define MAXBANKSPERDIMM 2
+#define MAXRANKSPERDIMM 2
+#define MAXBXCF 4 /* Changes le 12/01/05 pour 1.6 */
+#define MAXSDRAMMEMORY 0xFFFFFFFF /* 4GB */
+#define ERROR_STR_LENGTH 256
+#define MAX_SPD_BYTES 256 /* Max number of bytes on the DIMM's SPD EEPROM */
+
+/*----------------------------------------------------------------------------+
+| SDR Configuration registers
++----------------------------------------------------------------------------*/
+/* Serial Device Strap Reg 0 */
+#define sdr_pstrp0 0x0040
+
+#define SDR0_SDSTP1_EBC_ROM_BS_MASK 0x00000080 /* EBC Boot bus width Mask */
+#define SDR0_SDSTP1_EBC_ROM_BS_16BIT 0x00000080 /* EBC 16 Bits */
+#define SDR0_SDSTP1_EBC_ROM_BS_8BIT 0x00000000 /* EBC 8 Bits */
+
+#define SDR0_SDSTP1_BOOT_SEL_MASK 0x00080000 /* Boot device Selection Mask */
+#define SDR0_SDSTP1_BOOT_SEL_EBC 0x00000000 /* EBC */
+#define SDR0_SDSTP1_BOOT_SEL_PCI 0x00080000 /* PCI */
+
+#define SDR0_SDSTP1_EBC_SIZE_MASK 0x00000060 /* Boot rom size Mask */
+#define SDR0_SDSTP1_BOOT_SIZE_16MB 0x00000060 /* 16 MB */
+#define SDR0_SDSTP1_BOOT_SIZE_8MB 0x00000040 /* 8 MB */
+#define SDR0_SDSTP1_BOOT_SIZE_4MB 0x00000020 /* 4 MB */
+#define SDR0_SDSTP1_BOOT_SIZE_2MB 0x00000000 /* 2 MB */
+
+/* Serial Device Enabled - Addr = 0xA8 */
+#define SDR0_PSTRP0_BOOTSTRAP_IIC_A8_EN SDR0_PSTRP0_BOOTSTRAP_SETTINGS5
+/* Serial Device Enabled - Addr = 0xA4 */
+#define SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN SDR0_PSTRP0_BOOTSTRAP_SETTINGS7
+
+/* Pin Straps Reg */
+#define SDR0_PSTRP0 0x0040
+#define SDR0_PSTRP0_BOOTSTRAP_MASK 0xE0000000 /* Strap Bits */
+
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS1 0x20000000 /* Default strap settings 1 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS2 0x40000000 /* Default strap settings 2 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS3 0x60000000 /* Default strap settings 3 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS4 0x80000000 /* Default strap settings 4 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS5 0xA0000000 /* Default strap settings 5 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS6 0xC0000000 /* Default strap settings 6 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS7 0xE0000000 /* Default strap settings 7 */
+
+/* fpgareg - defines are in include/config/YUCCA.h */
+
+#define SDR0_CUST0_ENET3_MASK 0x00000080
+#define SDR0_CUST0_ENET3_COPPER 0x00000000
+#define SDR0_CUST0_ENET3_FIBER 0x00000080
+#define SDR0_CUST0_RGMII3_MASK 0x00000070
+#define SDR0_CUST0_RGMII3_ENCODE(n) ((((unsigned long)(n))&0x7)<<4)
+#define SDR0_CUST0_RGMII3_DECODE(n) ((((unsigned long)(n))>>4)&0x07)
+#define SDR0_CUST0_RGMII3_DISAB 0x00000000
+#define SDR0_CUST0_RGMII3_RTBI 0x00000040
+#define SDR0_CUST0_RGMII3_RGMII 0x00000050
+#define SDR0_CUST0_RGMII3_TBI 0x00000060
+#define SDR0_CUST0_RGMII3_GMII 0x00000070
+#define SDR0_CUST0_ENET2_MASK 0x00000008
+#define SDR0_CUST0_ENET2_COPPER 0x00000000
+#define SDR0_CUST0_ENET2_FIBER 0x00000008
+#define SDR0_CUST0_RGMII2_MASK 0x00000007
+#define SDR0_CUST0_RGMII2_ENCODE(n) ((((unsigned long)(n))&0x7)<<0)
+#define SDR0_CUST0_RGMII2_DECODE(n) ((((unsigned long)(n))>>0)&0x07)
+#define SDR0_CUST0_RGMII2_DISAB 0x00000000
+#define SDR0_CUST0_RGMII2_RTBI 0x00000004
+#define SDR0_CUST0_RGMII2_RGMII 0x00000005
+#define SDR0_CUST0_RGMII2_TBI 0x00000006
+#define SDR0_CUST0_RGMII2_GMII 0x00000007
+
+#define ONE_MILLION 1000000
+#define ONE_BILLION 1000000000
+
+/*----------------------------------------------------------------------------+
+| X
+| XX
+| XX XXX XXXXX XX XXX XXXXX
+| XX XX X XXX XX XX
+| XX XX XXXXXX XX XX
+| XX XX X XX XX XX XX
+| XXX XX XXXXX X XXXX XXX
++----------------------------------------------------------------------------*/
+/*----------------------------------------------------------------------------+
+| Declare Configuration values
++----------------------------------------------------------------------------*/
+
+typedef enum config_selection {
+ CONFIG_NOT_SELECTED,
+ CONFIG_SELECTED
+} config_selection_t;
+
+typedef enum config_list {
+ UART2_IN_SERVICE_MODE,
+ CPU_TRACE_MODE,
+ UART1_CTS_RTS,
+ CONFIG_NB
+} config_list_t;
+
+#define MAX_CONFIG_SELECT_NB 3
+
+#define BOARD_INFO_UART2_IN_SERVICE_MODE 1
+#define BOARD_INFO_CPU_TRACE_MODE 2
+#define BOARD_INFO_UART1_CTS_RTS_MODE 4
+
+void force_bup_config_selection(config_selection_t *confgi_select_P);
+void update_config_selection_table(config_selection_t *config_select_P);
+void display_config_selection(config_selection_t *config_select_P);
+
+/*----------------------------------------------------------------------------+
+| XX
+|
+| XXXX XX XXX XXX XXXX
+| XX XX XX XX XX XX
+| XX XXX XX XX XX XX XX
+| XX XX XXXXX XX XX XX
+| XXXX XX XXXX XXXX
+| XXXX
+|
+|
+|
+| +------------------------------------------------------------------+
+| | GPIO/Secondary func | Primary Function | I/O | Alternate1 | I/O |
+| +----------------------+------------------+-----+------------+-----+
+| | | | | | |
+| | GPIO0_0 | PCIX0REQ2_N | I/O | TRCCLK | |
+| | GPIO0_1 | PCIX0REQ3_N | I/O | TRCBS0 | |
+| | GPIO0_2 | PCIX0GNT2_N | I/O | TRCBS1 | |
+| | GPIO0_3 | PCIX0GNT3_N | I/O | TRCBS2 | |
+| | GPIO0_4 | PCIX1REQ2_N | I/O | TRCES0 | |
+| | GPIO0_5 | PCIX1REQ3_N | I/O | TRCES1 | |
+| | GPIO0_6 | PCIX1GNT2_N | I/O | TRCES2 | NA |
+| | GPIO0_7 | PCIX1GNT3_N | I/O | TRCES3 | NA |
+| | GPIO0_8 | PERREADY | I | TRCES4 | NA |
+| | GPIO0_9 | PERCS1_N | O | TRCTS0 | NA |
+| | GPIO0_10 | PERCS2_N | O | TRCTS1 | NA |
+| | GPIO0_11 | IRQ0 | I | TRCTS2 | NA |
+| | GPIO0_12 | IRQ1 | I | TRCTS3 | NA |
+| | GPIO0_13 | IRQ2 | I | TRCTS4 | NA |
+| | GPIO0_14 | IRQ3 | I | TRCTS5 | NA |
+| | GPIO0_15 | IRQ4 | I | TRCTS6 | NA |
+| | GPIO0_16 | IRQ5 | I | UART2RX | I |
+| | GPIO0_17 | PERBE0_N | O | UART2TX | O |
+| | GPIO0_18 | PCI0GNT0_N | I/O | NA | NA |
+| | GPIO0_19 | PCI0GNT1_N | I/O | NA | NA |
+| | GPIO0_20 | PCI0REQ0_N | I/O | NA | NA |
+| | GPIO0_21 | PCI0REQ1_N | I/O | NA | NA |
+| | GPIO0_22 | PCI1GNT0_N | I/O | NA | NA |
+| | GPIO0_23 | PCI1GNT1_N | I/O | NA | NA |
+| | GPIO0_24 | PCI1REQ0_N | I/O | NA | NA |
+| | GPIO0_25 | PCI1REQ1_N | I/O | NA | NA |
+| | GPIO0_26 | PCI2GNT0_N | I/O | NA | NA |
+| | GPIO0_27 | PCI2GNT1_N | I/O | NA | NA |
+| | GPIO0_28 | PCI2REQ0_N | I/O | NA | NA |
+| | GPIO0_29 | PCI2REQ1_N | I/O | NA | NA |
+| | GPIO0_30 | UART1RX | I | NA | NA |
+| | GPIO0_31 | UART1TX | O | NA | NA |
+| | | | | | |
+| +----------------------+------------------+-----+------------+-----+
+|
++----------------------------------------------------------------------------*/
+
+unsigned long auto_calc_speed(void);
+/*----------------------------------------------------------------------------+
+| Prototypes
++----------------------------------------------------------------------------*/
+void print_evb440spe_info(void);
+
+int onboard_pci_arbiter_selected(int core_pci);
+
+#ifdef __cplusplus
+}
+#endif
+#endif /* __YUCCA_H_ */
diff --git a/board/atc/Makefile b/board/atc/Makefile
index 7a2014d..7573a0c 100644
--- a/board/atc/Makefile
+++ b/board/atc/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o
+OBJS = $(BOARD).o flash.o ti113x.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/atc/ti113x.c b/board/atc/ti113x.c
new file mode 100644
index 0000000..d5e935c
--- /dev/null
+++ b/board/atc/ti113x.c
@@ -0,0 +1,637 @@
+/*
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ ********************************************************************
+ *
+ * Lots of code copied from:
+ *
+ * i82365.c 1.352 - Linux driver for Intel 82365 and compatible
+ * PC Card controllers, and Yenta-compatible PCI-to-CardBus controllers.
+ * (C) 1999 David A. Hinds <dahinds@users.sourceforge.net>
+ */
+
+#include <common.h>
+
+#ifdef CONFIG_I82365
+
+#include <command.h>
+#include <pci.h>
+#include <pcmcia.h>
+#include <asm/io.h>
+
+#include <pcmcia/ss.h>
+#include <pcmcia/i82365.h>
+#include <pcmcia/yenta.h>
+#include <pcmcia/ti113x.h>
+
+static struct pci_device_id supported[] = {
+ {PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_1510},
+ {0, 0}
+};
+
+#define CYCLE_TIME 120
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev);
+#endif
+
+typedef struct socket_info_t {
+ pci_dev_t dev;
+ u_short bcr;
+ u_char pci_lat, cb_lat, sub_bus, cache;
+ u_int cb_phys;
+
+ socket_cap_t cap;
+ u_short type;
+ u_int flags;
+ ti113x_state_t state;
+} socket_info_t;
+
+static socket_info_t socket;
+static socket_state_t state;
+static struct pccard_mem_map mem;
+static struct pccard_io_map io;
+
+/*====================================================================*/
+
+/* Some PCI shortcuts */
+
+static int pci_readb (socket_info_t * s, int r, u_char * v)
+{
+ return pci_read_config_byte (s->dev, r, v);
+}
+static int pci_writeb (socket_info_t * s, int r, u_char v)
+{
+ return pci_write_config_byte (s->dev, r, v);
+}
+static int pci_readw (socket_info_t * s, int r, u_short * v)
+{
+ return pci_read_config_word (s->dev, r, v);
+}
+static int pci_writew (socket_info_t * s, int r, u_short v)
+{
+ return pci_write_config_word (s->dev, r, v);
+}
+static int pci_readl (socket_info_t * s, int r, u_int * v)
+{
+ return pci_read_config_dword (s->dev, r, v);
+}
+static int pci_writel (socket_info_t * s, int r, u_int v)
+{
+ return pci_write_config_dword (s->dev, r, v);
+}
+
+/*====================================================================*/
+
+#define cb_readb(s, r) readb((s)->cb_phys + (r))
+#define cb_readl(s, r) readl((s)->cb_phys + (r))
+#define cb_writeb(s, r, v) writeb(v, (s)->cb_phys + (r))
+#define cb_writel(s, r, v) writel(v, (s)->cb_phys + (r))
+
+static u_char i365_get (socket_info_t * s, u_short reg)
+{
+ return cb_readb (s, 0x0800 + reg);
+}
+
+static void i365_set (socket_info_t * s, u_short reg, u_char data)
+{
+ cb_writeb (s, 0x0800 + reg, data);
+}
+
+static void i365_bset (socket_info_t * s, u_short reg, u_char mask)
+{
+ i365_set (s, reg, i365_get (s, reg) | mask);
+}
+
+static void i365_bclr (socket_info_t * s, u_short reg, u_char mask)
+{
+ i365_set (s, reg, i365_get (s, reg) & ~mask);
+}
+
+#if 0 /* not used */
+static void i365_bflip (socket_info_t * s, u_short reg, u_char mask, int b)
+{
+ u_char d = i365_get (s, reg);
+
+ i365_set (s, reg, (b) ? (d | mask) : (d & ~mask));
+}
+
+static u_short i365_get_pair (socket_info_t * s, u_short reg)
+{
+ return (i365_get (s, reg) + (i365_get (s, reg + 1) << 8));
+}
+#endif /* not used */
+
+static void i365_set_pair (socket_info_t * s, u_short reg, u_short data)
+{
+ i365_set (s, reg, data & 0xff);
+ i365_set (s, reg + 1, data >> 8);
+}
+
+/*======================================================================
+
+ Code to save and restore global state information for TI 1130 and
+ TI 1131 controllers, and to set and report global configuration
+ options.
+
+======================================================================*/
+
+static void ti113x_get_state (socket_info_t * s)
+{
+ ti113x_state_t *p = &s->state;
+
+ pci_readl (s, TI113X_SYSTEM_CONTROL, &p->sysctl);
+ pci_readb (s, TI113X_CARD_CONTROL, &p->cardctl);
+ pci_readb (s, TI113X_DEVICE_CONTROL, &p->devctl);
+ pci_readb (s, TI1250_DIAGNOSTIC, &p->diag);
+ pci_readl (s, TI12XX_IRQMUX, &p->irqmux);
+}
+
+static void ti113x_set_state (socket_info_t * s)
+{
+ ti113x_state_t *p = &s->state;
+
+ pci_writel (s, TI113X_SYSTEM_CONTROL, p->sysctl);
+ pci_writeb (s, TI113X_CARD_CONTROL, p->cardctl);
+ pci_writeb (s, TI113X_DEVICE_CONTROL, p->devctl);
+ pci_writeb (s, TI1250_MULTIMEDIA_CTL, 0);
+ pci_writeb (s, TI1250_DIAGNOSTIC, p->diag);
+ pci_writel (s, TI12XX_IRQMUX, p->irqmux);
+ i365_set_pair (s, TI113X_IO_OFFSET (0), 0);
+ i365_set_pair (s, TI113X_IO_OFFSET (1), 0);
+}
+
+static u_int ti113x_set_opts (socket_info_t * s)
+{
+ ti113x_state_t *p = &s->state;
+ u_int mask = 0xffff;
+
+ p->cardctl &= ~TI113X_CCR_ZVENABLE;
+ p->cardctl |= TI113X_CCR_SPKROUTEN;
+
+ return mask;
+}
+
+/*======================================================================
+
+ Routines to handle common CardBus options
+
+======================================================================*/
+
+/* Default settings for PCI command configuration register */
+#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
+ PCI_COMMAND_MASTER|PCI_COMMAND_WAIT)
+
+static void cb_get_state (socket_info_t * s)
+{
+ pci_readb (s, PCI_CACHE_LINE_SIZE, &s->cache);
+ pci_readb (s, PCI_LATENCY_TIMER, &s->pci_lat);
+ pci_readb (s, CB_LATENCY_TIMER, &s->cb_lat);
+ pci_readb (s, CB_CARDBUS_BUS, &s->cap.cardbus);
+ pci_readb (s, CB_SUBORD_BUS, &s->sub_bus);
+ pci_readw (s, CB_BRIDGE_CONTROL, &s->bcr);
+}
+
+static void cb_set_state (socket_info_t * s)
+{
+ pci_writel (s, CB_LEGACY_MODE_BASE, 0);
+ pci_writel (s, PCI_BASE_ADDRESS_0, s->cb_phys);
+ pci_writew (s, PCI_COMMAND, CMD_DFLT);
+ pci_writeb (s, PCI_CACHE_LINE_SIZE, s->cache);
+ pci_writeb (s, PCI_LATENCY_TIMER, s->pci_lat);
+ pci_writeb (s, CB_LATENCY_TIMER, s->cb_lat);
+ pci_writeb (s, CB_CARDBUS_BUS, s->cap.cardbus);
+ pci_writeb (s, CB_SUBORD_BUS, s->sub_bus);
+ pci_writew (s, CB_BRIDGE_CONTROL, s->bcr);
+}
+
+static void cb_set_opts (socket_info_t * s)
+{
+ if (s->cache == 0)
+ s->cache = 8;
+ if (s->pci_lat == 0)
+ s->pci_lat = 0xa8;
+ if (s->cb_lat == 0)
+ s->cb_lat = 0xb0;
+}
+
+/*======================================================================
+
+ Power control for Cardbus controllers: used both for 16-bit and
+ Cardbus cards.
+
+======================================================================*/
+
+static int cb_set_power (socket_info_t * s, socket_state_t * state)
+{
+ u_int reg = 0;
+
+ /* restart card voltage detection if it seems appropriate */
+ if ((state->Vcc == 0) && (state->Vpp == 0) &&
+ !(cb_readl (s, CB_SOCKET_STATE) & CB_SS_VSENSE))
+ cb_writel (s, CB_SOCKET_FORCE, CB_SF_CVSTEST);
+ switch (state->Vcc) {
+ case 0:
+ reg = 0;
+ break;
+ case 33:
+ reg = CB_SC_VCC_3V;
+ break;
+ case 50:
+ reg = CB_SC_VCC_5V;
+ break;
+ default:
+ return -1;
+ }
+ switch (state->Vpp) {
+ case 0:
+ break;
+ case 33:
+ reg |= CB_SC_VPP_3V;
+ break;
+ case 50:
+ reg |= CB_SC_VPP_5V;
+ break;
+ case 120:
+ reg |= CB_SC_VPP_12V;
+ break;
+ default:
+ return -1;
+ }
+ if (reg != cb_readl (s, CB_SOCKET_CONTROL))
+ cb_writel (s, CB_SOCKET_CONTROL, reg);
+
+ return 0;
+}
+
+/*======================================================================
+
+ Generic routines to get and set controller options
+
+======================================================================*/
+
+static void get_bridge_state (socket_info_t * s)
+{
+ ti113x_get_state (s);
+ cb_get_state (s);
+}
+
+static void set_bridge_state (socket_info_t * s)
+{
+ cb_set_state (s);
+ i365_set (s, I365_GBLCTL, 0x00);
+ i365_set (s, I365_GENCTL, 0x00);
+ ti113x_set_state (s);
+}
+
+static void set_bridge_opts (socket_info_t * s)
+{
+ ti113x_set_opts (s);
+ cb_set_opts (s);
+}
+
+/*====================================================================*/
+#define PD67_EXT_INDEX 0x2e /* Extension index */
+#define PD67_EXT_DATA 0x2f /* Extension data */
+#define PD67_EXD_VS1(s) (0x01 << ((s)<<1))
+
+#define pd67_ext_get(s, r) \
+ (i365_set(s, PD67_EXT_INDEX, r), i365_get(s, PD67_EXT_DATA))
+
+static int i365_get_status (socket_info_t * s, u_int * value)
+{
+ u_int status;
+
+ status = i365_get (s, I365_IDENT);
+ status = i365_get (s, I365_STATUS);
+ *value = ((status & I365_CS_DETECT) == I365_CS_DETECT) ? SS_DETECT : 0;
+ if (i365_get (s, I365_INTCTL) & I365_PC_IOCARD) {
+ *value |= (status & I365_CS_STSCHG) ? 0 : SS_STSCHG;
+ } else {
+ *value |= (status & I365_CS_BVD1) ? 0 : SS_BATDEAD;
+ *value |= (status & I365_CS_BVD2) ? 0 : SS_BATWARN;
+ }
+ *value |= (status & I365_CS_WRPROT) ? SS_WRPROT : 0;
+ *value |= (status & I365_CS_READY) ? SS_READY : 0;
+ *value |= (status & I365_CS_POWERON) ? SS_POWERON : 0;
+
+ status = cb_readl (s, CB_SOCKET_STATE);
+ *value |= (status & CB_SS_32BIT) ? SS_CARDBUS : 0;
+ *value |= (status & CB_SS_3VCARD) ? SS_3VCARD : 0;
+ *value |= (status & CB_SS_XVCARD) ? SS_XVCARD : 0;
+ *value |= (status & CB_SS_VSENSE) ? 0 : SS_PENDING;
+ /* For now, ignore cards with unsupported voltage keys */
+ if (*value & SS_XVCARD)
+ *value &= ~(SS_DETECT | SS_3VCARD | SS_XVCARD);
+
+ return 0;
+} /* i365_get_status */
+
+static int i365_set_socket (socket_info_t * s, socket_state_t * state)
+{
+ u_char reg;
+
+ set_bridge_state (s);
+
+ /* IO card, RESET flag */
+ reg = 0;
+ reg |= (state->flags & SS_RESET) ? 0 : I365_PC_RESET;
+ reg |= (state->flags & SS_IOCARD) ? I365_PC_IOCARD : 0;
+ i365_set (s, I365_INTCTL, reg);
+
+ reg = I365_PWR_NORESET;
+ if (state->flags & SS_PWR_AUTO)
+ reg |= I365_PWR_AUTO;
+ if (state->flags & SS_OUTPUT_ENA)
+ reg |= I365_PWR_OUT;
+
+ cb_set_power (s, state);
+ reg |= i365_get (s, I365_POWER) & (I365_VCC_MASK | I365_VPP1_MASK);
+
+ if (reg != i365_get (s, I365_POWER))
+ i365_set (s, I365_POWER, reg);
+
+ return 0;
+} /* i365_set_socket */
+
+/*====================================================================*/
+
+static int i365_set_mem_map (socket_info_t * s, struct pccard_mem_map *mem)
+{
+ u_short base, i;
+ u_char map;
+
+ debug ("i82365: SetMemMap(%d, %#2.2x, %d ns, %#5.5lx-%#5.5lx, %#5.5x)\n",
+ mem->map, mem->flags, mem->speed,
+ mem->sys_start, mem->sys_stop, mem->card_start);
+
+ map = mem->map;
+ if ((map > 4) ||
+ (mem->card_start > 0x3ffffff) ||
+ (mem->sys_start > mem->sys_stop) ||
+ (mem->speed > 1000)) {
+ return -1;
+ }
+
+ /* Turn off the window before changing anything */
+ if (i365_get (s, I365_ADDRWIN) & I365_ENA_MEM (map))
+ i365_bclr (s, I365_ADDRWIN, I365_ENA_MEM (map));
+
+ /* Take care of high byte, for PCI controllers */
+ i365_set (s, CB_MEM_PAGE (map), mem->sys_start >> 24);
+
+ base = I365_MEM (map);
+ i = (mem->sys_start >> 12) & 0x0fff;
+ if (mem->flags & MAP_16BIT)
+ i |= I365_MEM_16BIT;
+ if (mem->flags & MAP_0WS)
+ i |= I365_MEM_0WS;
+ i365_set_pair (s, base + I365_W_START, i);
+
+ i = (mem->sys_stop >> 12) & 0x0fff;
+ switch (mem->speed / CYCLE_TIME) {
+ case 0:
+ break;
+ case 1:
+ i |= I365_MEM_WS0;
+ break;
+ case 2:
+ i |= I365_MEM_WS1;
+ break;
+ default:
+ i |= I365_MEM_WS1 | I365_MEM_WS0;
+ break;
+ }
+ i365_set_pair (s, base + I365_W_STOP, i);
+
+ i = ((mem->card_start - mem->sys_start) >> 12) & 0x3fff;
+ if (mem->flags & MAP_WRPROT)
+ i |= I365_MEM_WRPROT;
+ if (mem->flags & MAP_ATTRIB)
+ i |= I365_MEM_REG;
+ i365_set_pair (s, base + I365_W_OFF, i);
+
+ /* Turn on the window if necessary */
+ if (mem->flags & MAP_ACTIVE)
+ i365_bset (s, I365_ADDRWIN, I365_ENA_MEM (map));
+ return 0;
+} /* i365_set_mem_map */
+
+static int i365_set_io_map (socket_info_t * s, struct pccard_io_map *io)
+{
+ u_char map, ioctl;
+
+ map = io->map;
+ /* comment out: comparison is always false due to limited range of data type */
+ if ((map > 1) || /* (io->start > 0xffff) || (io->stop > 0xffff) || */
+ (io->stop < io->start))
+ return -1;
+ /* Turn off the window before changing anything */
+ if (i365_get (s, I365_ADDRWIN) & I365_ENA_IO (map))
+ i365_bclr (s, I365_ADDRWIN, I365_ENA_IO (map));
+ i365_set_pair (s, I365_IO (map) + I365_W_START, io->start);
+ i365_set_pair (s, I365_IO (map) + I365_W_STOP, io->stop);
+ ioctl = i365_get (s, I365_IOCTL) & ~I365_IOCTL_MASK (map);
+ if (io->speed)
+ ioctl |= I365_IOCTL_WAIT (map);
+ if (io->flags & MAP_0WS)
+ ioctl |= I365_IOCTL_0WS (map);
+ if (io->flags & MAP_16BIT)
+ ioctl |= I365_IOCTL_16BIT (map);
+ if (io->flags & MAP_AUTOSZ)
+ ioctl |= I365_IOCTL_IOCS16 (map);
+ i365_set (s, I365_IOCTL, ioctl);
+ /* Turn on the window if necessary */
+ if (io->flags & MAP_ACTIVE)
+ i365_bset (s, I365_ADDRWIN, I365_ENA_IO (map));
+ return 0;
+} /* i365_set_io_map */
+
+/*====================================================================*/
+
+int i82365_init (void)
+{
+ u_int val;
+ int i;
+
+ if ((socket.dev = pci_find_devices (supported, 0)) < 0) {
+ /* Controller not found */
+ return 1;
+ }
+ debug ("i82365 Device Found!\n");
+
+ pci_read_config_dword (socket.dev, PCI_BASE_ADDRESS_0, &socket.cb_phys);
+ socket.cb_phys &= ~0xf;
+
+ get_bridge_state (&socket);
+ set_bridge_opts (&socket);
+
+ i = i365_get_status (&socket, &val);
+
+ if (val & SS_DETECT) {
+ if (val & SS_3VCARD) {
+ state.Vcc = state.Vpp = 33;
+ puts (" 3.3V card found: ");
+ } else if (!(val & SS_XVCARD)) {
+ state.Vcc = state.Vpp = 50;
+ puts (" 5.0V card found: ");
+ } else {
+ puts ("i82365: unsupported voltage key\n");
+ state.Vcc = state.Vpp = 0;
+ }
+ } else {
+ /* No card inserted */
+ puts ("No card\n");
+ return 1;
+ }
+
+ state.flags = SS_IOCARD | SS_OUTPUT_ENA;
+ state.csc_mask = 0;
+ state.io_irq = 0;
+
+ i365_set_socket (&socket, &state);
+
+ for (i = 500; i; i--) {
+ if ((i365_get (&socket, I365_STATUS) & I365_CS_READY))
+ break;
+ udelay (1000);
+ }
+
+ if (i == 0) {
+ /* PC Card not ready for data transfer */
+ puts ("i82365 PC Card not ready for data transfer\n");
+ return 1;
+ }
+ debug (" PC Card ready for data transfer: ");
+
+ mem.map = 0;
+ mem.flags = MAP_ATTRIB | MAP_ACTIVE;
+ mem.speed = 300;
+ mem.sys_start = CFG_PCMCIA_MEM_ADDR;
+ mem.sys_stop = CFG_PCMCIA_MEM_ADDR + CFG_PCMCIA_MEM_SIZE - 1;
+ mem.card_start = 0;
+ i365_set_mem_map (&socket, &mem);
+
+ io.map = 0;
+ io.flags = MAP_AUTOSZ | MAP_ACTIVE;
+ io.speed = 0;
+ io.start = 0x0100;
+ io.stop = 0x010F;
+ i365_set_io_map (&socket, &io);
+
+#ifdef DEBUG
+ i82365_dump_regions (socket.dev);
+#endif
+
+ return 0;
+}
+
+void i82365_exit (void)
+{
+ io.map = 0;
+ io.flags = 0;
+ io.speed = 0;
+ io.start = 0;
+ io.stop = 0x1;
+
+ i365_set_io_map (&socket, &io);
+
+ mem.map = 0;
+ mem.flags = 0;
+ mem.speed = 0;
+ mem.sys_start = 0;
+ mem.sys_stop = 0x1000;
+ mem.card_start = 0;
+
+ i365_set_mem_map (&socket, &mem);
+
+ socket.state.sysctl &= 0xFFFF00FF;
+
+ state.Vcc = state.Vpp = 0;
+
+ i365_set_socket (&socket, &state);
+}
+
+int pcmcia_on (void)
+{
+ u_int rc;
+
+ debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+ rc = i82365_init();
+ if (rc)
+ goto exit;
+
+ rc = check_ide_device(0);
+ if (rc == 0)
+ goto exit;
+
+ i82365_exit();
+
+exit:
+ return rc;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_off (void)
+{
+ printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+ i82365_exit();
+
+ return 0;
+}
+#endif
+
+/*======================================================================
+
+ Debug stuff
+
+======================================================================*/
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev)
+{
+ u_int tmp[2];
+ u_int *mem = (void *) socket.cb_phys;
+ u_char *cis = (void *) CFG_PCMCIA_MEM_ADDR;
+ u_char *ide = (void *) (CFG_ATA_BASE_ADDR + CFG_ATA_REG_OFFSET);
+
+ pci_read_config_dword (dev, 0x00, tmp + 0);
+ pci_read_config_dword (dev, 0x80, tmp + 1);
+
+ printf ("PCI CONF: %08X ... %08X\n",
+ tmp[0], tmp[1]);
+ printf ("PCI MEM: ... %08X ... %08X\n",
+ mem[0x8 / 4], mem[0x800 / 4]);
+ printf ("CIS: ...%c%c%c%c%c%c%c%c...\n",
+ cis[0x38], cis[0x3a], cis[0x3c], cis[0x3e],
+ cis[0x40], cis[0x42], cis[0x44], cis[0x48]);
+ printf ("CIS CONF: %02X %02X %02X ...\n",
+ cis[0x200], cis[0x202], cis[0x204]);
+ printf ("IDE: %02X %02X %02X %02X %02X %02X %02X %02X\n",
+ ide[0], ide[1], ide[2], ide[3],
+ ide[4], ide[5], ide[6], ide[7]);
+}
+#endif /* DEBUG */
+
+#endif /* CONFIG_I82365 */
diff --git a/board/c2mon/Makefile b/board/c2mon/Makefile
index 7a2014d..7b2b545 100644
--- a/board/c2mon/Makefile
+++ b/board/c2mon/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o
+OBJS = $(BOARD).o flash.o pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/c2mon/pcmcia.c b/board/c2mon/pcmcia.c
new file mode 100644
index 0000000..5e50c4d
--- /dev/null
+++ b/board/c2mon/pcmcia.c
@@ -0,0 +1,284 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "C2MON"
+
+static void cfg_ports (void)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ ushort sreg;
+
+ immap = (immap_t *)CFG_IMMR;
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /*
+ * Configure Port C for TPS2211 PC-Card Power-Interface Switch
+ *
+ * Switch off all voltages, assert shutdown
+ */
+ sreg = immap->im_ioport.iop_pcdat;
+ sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1); /* VAVPP => Hi-Z */
+ sreg &= ~(TPS2211_VCCD0 | TPS2211_VCCD1); /* 3V and 5V off */
+ immap->im_ioport.iop_pcdat = sreg;
+
+ immap->im_ioport.iop_pcpar &= ~(TPS2211_OUTPUTS);
+ immap->im_ioport.iop_pcdir |= TPS2211_OUTPUTS;
+
+ debug ("Set Port C: PAR: %04x DIR: %04x DAT: %04x\n",
+ immap->im_ioport.iop_pcpar,
+ immap->im_ioport.iop_pcdir,
+ immap->im_ioport.iop_pcdat);
+
+ /*
+ * Configure Port B for TPS2211 PC-Card Power-Interface Switch
+ *
+ * Over-Current Input only
+ */
+ cp->cp_pbpar &= ~(TPS2211_INPUTS);
+ cp->cp_pbdir &= ~(TPS2211_INPUTS);
+
+ debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
+ cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ volatile sysconf8xx_t *sysp;
+ uint reg, pipr, mask;
+ ushort sreg;
+ int i;
+
+ debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ udelay(10000);
+
+ immap = (immap_t *)CFG_IMMR;
+ sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+ cfg_ports ();
+
+ /*
+ * Configure SIUMCR to enable PCMCIA port B
+ * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+ */
+ sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
+ pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Make sure there is a card in the slot, then configure the interface.
+ */
+ udelay(10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n",
+ __LINE__,__FUNCTION__,
+ &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+ if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ /*
+ * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+ */
+ mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+ pipr = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+ pipr,
+ (reg&PCMCIA_VS1(slot))?"n":"ff",
+ (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+ sreg = immap->im_ioport.iop_pcdat;
+ if ((pipr & mask) == mask) {
+ sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1 | /* VAVPP => Hi-Z */
+ TPS2211_VCCD1); /* 5V on */
+ sreg &= ~(TPS2211_VCCD0); /* 3V off */
+ puts (" 5.0V card found: ");
+ } else {
+ sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1 | /* VAVPP => Hi-Z */
+ TPS2211_VCCD0); /* 3V on */
+ sreg &= ~(TPS2211_VCCD1); /* 5V off */
+ puts (" 3.3V card found: ");
+ }
+
+ debug ("\nPC DAT: %04x -> 3.3V %s 5.0V %s\n",
+ sreg,
+ ( (sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) ? "on" : "off",
+ (!(sreg & TPS2211_VCCD0) && (sreg & TPS2211_VCCD1)) ? "on" : "off"
+ );
+
+ immap->im_ioport.iop_pcdat = sreg;
+
+ /* Wait 500 ms; use this to check for over-current */
+ for (i=0; i<5000; ++i) {
+ if ((cp->cp_pbdat & TPS2211_OC) == 0) {
+ printf (" *** Overcurrent - Safety shutdown ***\n");
+ immap->im_ioport.iop_pcdat &= ~(TPS2211_VCCD0|TPS2211_VCCD1);
+ return (1);
+ }
+ udelay (100);
+ }
+
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+ /* Configure PCMCIA General Control Register */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ /* ALl voltages off / Hi-Z */
+ immap->im_ioport.iop_pcdat |= (TPS2211_VPPD0 | TPS2211_VPPD1 |
+ TPS2211_VCCD0 | TPS2211_VCCD1 );
+
+ udelay(10000);
+
+ return (0);
+}
+#endif /* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+ ushort sreg;
+
+ debug ("voltage_set: "
+ PCMCIA_BOARD_MSG
+ " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+ 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+ immap = (immap_t *)CFG_IMMR;
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ /*
+ * Disable PCMCIA buffers (isolate the interface)
+ * and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Configure Port C pins for
+ * 5 Volts Enable and 3 Volts enable,
+ * Turn all power pins to Hi-Z
+ */
+ debug ("PCMCIA power OFF\n");
+ cfg_ports (); /* Enables switch, but all in Hi-Z */
+
+ sreg = immap->im_ioport.iop_pcdat;
+ sreg |= TPS2211_VPPD0 | TPS2211_VPPD1; /* VAVPP always Hi-Z */
+
+ switch(vcc) {
+ case 0: break; /* Switch off */
+ case 33: sreg |= TPS2211_VCCD0; /* Switch on 3.3V */
+ sreg &= ~TPS2211_VCCD1;
+ break;
+ case 50: sreg &= ~TPS2211_VCCD0; /* Switch on 5.0V */
+ sreg |= TPS2211_VCCD1;
+ break;
+ default: goto done;
+ }
+
+ /* Checking supported voltages */
+
+ debug ("PIPR: 0x%x --> %s\n",
+ pcmp->pcmc_pipr,
+ (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+ immap->im_ioport.iop_pcdat = sreg;
+
+#ifdef DEBUG
+{
+ char *s;
+
+ if ((sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) {
+ s = "at 3.3V";
+ } else if (!(sreg & TPS2211_VCCD0) && (sreg & TPS2211_VCCD1)) {
+ s = "at 5.0V";
+ } else {
+ s = "down";
+ }
+ printf ("PCMCIA powered %s\n", s);
+}
+#endif
+
+done:
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+ slot+'A');
+ return (0);
+}
+
+#endif /* CONFIG_PCMCIA */
diff --git a/board/cpc45/pd67290.c b/board/cpc45/pd67290.c
index c84fbae..6ca3e7b 100644
--- a/board/cpc45/pd67290.c
+++ b/board/cpc45/pd67290.c
@@ -1,4 +1,6 @@
-/* pd67290.c - system configuration module for SPD67290
+/*
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,51 +20,799 @@
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
- * (C) 2004 DENX Software Engineering, Heiko Schocher <hs@denx.de>
+ ********************************************************************
+ *
+ * Lots of code copied from:
+ *
+ * i82365.c 1.352 - Linux driver for Intel 82365 and compatible
+ * PC Card controllers, and Yenta-compatible PCI-to-CardBus controllers.
+ * (C) 1999 David A. Hinds <dahinds@users.sourceforge.net>
*/
#include <common.h>
-#include <malloc.h>
-#include <net.h>
-#include <asm/io.h>
-#include <pci.h>
-/* imports */
-#include <mpc824x.h>
+#ifdef CONFIG_I82365
+
+#include <command.h>
+#include <pci.h>
+#include <pcmcia.h>
+#include <asm/io.h>
+
+#include <pcmcia/ss.h>
+#include <pcmcia/i82365.h>
+#include <pcmcia/yenta.h>
+#include <pcmcia/cirrus.h>
static struct pci_device_id supported[] = {
{PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_6729},
- {}
+ {0, 0}
};
-/***************************************************************************
-*
-* SPD67290Init -
-*
-* RETURNS: -1 on error, 0 if OK
-*/
+#define CYCLE_TIME 120
-int SPD67290Init (void)
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev);
+#endif
+
+typedef struct socket_info_t {
+ pci_dev_t dev;
+ u_short bcr;
+ u_char pci_lat, cb_lat, sub_bus, cache;
+ u_int cb_phys;
+
+ socket_cap_t cap;
+ u_short type;
+ u_int flags;
+ cirrus_state_t c_state;
+} socket_info_t;
+
+/* These definitions must match the pcic table! */
+typedef enum pcic_id {
+ IS_PD6710, IS_PD672X, IS_VT83C469
+} pcic_id;
+
+typedef struct pcic_t {
+ char *name;
+} pcic_t;
+
+static pcic_t pcic[] = {
+ {" Cirrus PD6710: "},
+ {" Cirrus PD672x: "},
+ {" VIA VT83C469: "},
+};
+
+static socket_info_t socket;
+static socket_state_t state;
+static struct pccard_mem_map mem;
+static struct pccard_io_map io;
+
+/*====================================================================*/
+
+/* Some PCI shortcuts */
+
+static int pci_readb (socket_info_t * s, int r, u_char * v)
{
- pci_dev_t devno;
- int idx = 0; /* general index */
- ulong membaseCsr; /* base address of device memory space */
+ return pci_read_config_byte (s->dev, r, v);
+}
+static int pci_writeb (socket_info_t * s, int r, u_char v)
+{
+ return pci_write_config_byte (s->dev, r, v);
+}
+static int pci_readw (socket_info_t * s, int r, u_short * v)
+{
+ return pci_read_config_word (s->dev, r, v);
+}
+static int pci_writew (socket_info_t * s, int r, u_short v)
+{
+ return pci_write_config_word (s->dev, r, v);
+}
- /* find PD67290 device */
- if ((devno = pci_find_devices (supported, idx++)) < 0) {
- printf ("No PD67290 device found !!\n");
+/*====================================================================*/
+
+#define cb_readb(s) readb((s)->cb_phys + 1)
+#define cb_writeb(s, v) writeb(v, (s)->cb_phys)
+#define cb_writeb2(s, v) writeb(v, (s)->cb_phys + 1)
+#define cb_readl(s, r) readl((s)->cb_phys + (r))
+#define cb_writel(s, r, v) writel(v, (s)->cb_phys + (r))
+
+
+static u_char i365_get (socket_info_t * s, u_short reg)
+{
+ u_char val;
+#ifdef CONFIG_PCMCIA_SLOT_A
+ int slot = 0;
+#else
+ int slot = 1;
+#endif
+
+ val = I365_REG (slot, reg);
+
+ cb_writeb (s, val);
+ val = cb_readb (s);
+
+ debug ("i365_get slot:%x reg: %x val: %x\n", slot, reg, val);
+ return val;
+}
+
+static void i365_set (socket_info_t * s, u_short reg, u_char data)
+{
+#ifdef CONFIG_PCMCIA_SLOT_A
+ int slot = 0;
+#else
+ int slot = 1;
+#endif
+ u_char val;
+
+ val = I365_REG (slot, reg);
+
+ cb_writeb (s, val);
+ cb_writeb2 (s, data);
+
+ debug ("i365_set slot:%x reg: %x data:%x\n", slot, reg, data);
+}
+
+static void i365_bset (socket_info_t * s, u_short reg, u_char mask)
+{
+ i365_set (s, reg, i365_get (s, reg) | mask);
+}
+
+static void i365_bclr (socket_info_t * s, u_short reg, u_char mask)
+{
+ i365_set (s, reg, i365_get (s, reg) & ~mask);
+}
+
+#if 0 /* not used */
+static void i365_bflip (socket_info_t * s, u_short reg, u_char mask, int b)
+{
+ u_char d = i365_get (s, reg);
+
+ i365_set (s, reg, (b) ? (d | mask) : (d & ~mask));
+}
+
+static u_short i365_get_pair (socket_info_t * s, u_short reg)
+{
+ return (i365_get (s, reg) + (i365_get (s, reg + 1) << 8));
+}
+#endif /* not used */
+
+static void i365_set_pair (socket_info_t * s, u_short reg, u_short data)
+{
+ i365_set (s, reg, data & 0xff);
+ i365_set (s, reg + 1, data >> 8);
+}
+
+/*======================================================================
+
+ Code to save and restore global state information for Cirrus
+ PD67xx controllers, and to set and report global configuration
+ options.
+
+======================================================================*/
+
+#define flip(v,b,f) (v = ((f)<0) ? v : ((f) ? ((v)|(b)) : ((v)&(~b))))
+
+static void cirrus_get_state (socket_info_t * s)
+{
+ int i;
+ cirrus_state_t *p = &s->c_state;
+
+ p->misc1 = i365_get (s, PD67_MISC_CTL_1);
+ p->misc1 &= (PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
+ p->misc2 = i365_get (s, PD67_MISC_CTL_2);
+ for (i = 0; i < 6; i++)
+ p->timer[i] = i365_get (s, PD67_TIME_SETUP (0) + i);
+
+}
+
+static void cirrus_set_state (socket_info_t * s)
+{
+ int i;
+ u_char misc;
+ cirrus_state_t *p = &s->c_state;
+
+ misc = i365_get (s, PD67_MISC_CTL_2);
+ i365_set (s, PD67_MISC_CTL_2, p->misc2);
+ if (misc & PD67_MC2_SUSPEND)
+ udelay (50000);
+ misc = i365_get (s, PD67_MISC_CTL_1);
+ misc &= ~(PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
+ i365_set (s, PD67_MISC_CTL_1, misc | p->misc1);
+ for (i = 0; i < 6; i++)
+ i365_set (s, PD67_TIME_SETUP (0) + i, p->timer[i]);
+}
+
+static u_int cirrus_set_opts (socket_info_t * s)
+{
+ cirrus_state_t *p = &s->c_state;
+ u_int mask = 0xffff;
+#if DEBUG
+ char buf[200];
+
+ memset (buf, 0, 200);
+#endif
+
+ if (has_ring == -1)
+ has_ring = 1;
+ flip (p->misc2, PD67_MC2_IRQ15_RI, has_ring);
+ flip (p->misc2, PD67_MC2_DYNAMIC_MODE, dynamic_mode);
+#if DEBUG
+ if (p->misc2 & PD67_MC2_IRQ15_RI)
+ strcat (buf, " [ring]");
+ if (p->misc2 & PD67_MC2_DYNAMIC_MODE)
+ strcat (buf, " [dyn mode]");
+ if (p->misc1 & PD67_MC1_INPACK_ENA)
+ strcat (buf, " [inpack]");
+#endif
+
+ if (p->misc2 & PD67_MC2_IRQ15_RI)
+ mask &= ~0x8000;
+ if (has_led > 0) {
+#if DEBUG
+ strcat (buf, " [led]");
+#endif
+ mask &= ~0x1000;
+ }
+ if (has_dma > 0) {
+#if DEBUG
+ strcat (buf, " [dma]");
+#endif
+ mask &= ~0x0600;
+ flip (p->misc2, PD67_MC2_FREQ_BYPASS, freq_bypass);
+#if DEBUG
+ if (p->misc2 & PD67_MC2_FREQ_BYPASS)
+ strcat (buf, " [freq bypass]");
+#endif
+ }
+
+ if (setup_time >= 0)
+ p->timer[0] = p->timer[3] = setup_time;
+ if (cmd_time > 0) {
+ p->timer[1] = cmd_time;
+ p->timer[4] = cmd_time * 2 + 4;
+ }
+ if (p->timer[1] == 0) {
+ p->timer[1] = 6;
+ p->timer[4] = 16;
+ if (p->timer[0] == 0)
+ p->timer[0] = p->timer[3] = 1;
+ }
+ if (recov_time >= 0)
+ p->timer[2] = p->timer[5] = recov_time;
+
+ debug ("i82365 Opt: %s [%d/%d/%d] [%d/%d/%d]\n",
+ buf,
+ p->timer[0], p->timer[1], p->timer[2],
+ p->timer[3], p->timer[4], p->timer[5]);
+
+ return mask;
+}
+
+/*======================================================================
+
+ Routines to handle common CardBus options
+
+======================================================================*/
+
+/* Default settings for PCI command configuration register */
+#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
+ PCI_COMMAND_MASTER|PCI_COMMAND_WAIT)
+
+static void cb_get_state (socket_info_t * s)
+{
+ pci_readb (s, PCI_CACHE_LINE_SIZE, &s->cache);
+ pci_readb (s, PCI_LATENCY_TIMER, &s->pci_lat);
+ pci_readb (s, CB_LATENCY_TIMER, &s->cb_lat);
+ pci_readb (s, CB_CARDBUS_BUS, &s->cap.cardbus);
+ pci_readb (s, CB_SUBORD_BUS, &s->sub_bus);
+ pci_readw (s, CB_BRIDGE_CONTROL, &s->bcr);
+}
+
+static void cb_set_state (socket_info_t * s)
+{
+ pci_writew (s, PCI_COMMAND, CMD_DFLT);
+ pci_writeb (s, PCI_CACHE_LINE_SIZE, s->cache);
+ pci_writeb (s, PCI_LATENCY_TIMER, s->pci_lat);
+ pci_writeb (s, CB_LATENCY_TIMER, s->cb_lat);
+ pci_writeb (s, CB_CARDBUS_BUS, s->cap.cardbus);
+ pci_writeb (s, CB_SUBORD_BUS, s->sub_bus);
+ pci_writew (s, CB_BRIDGE_CONTROL, s->bcr);
+}
+
+static void cb_set_opts (socket_info_t * s)
+{
+}
+
+/*======================================================================
+
+ Power control for Cardbus controllers: used both for 16-bit and
+ Cardbus cards.
+
+======================================================================*/
+
+static int cb_set_power (socket_info_t * s, socket_state_t * state)
+{
+ u_int reg = 0;
+
+ reg = I365_PWR_NORESET;
+ if (state->flags & SS_PWR_AUTO)
+ reg |= I365_PWR_AUTO;
+ if (state->flags & SS_OUTPUT_ENA)
+ reg |= I365_PWR_OUT;
+ if (state->Vpp != 0) {
+ if (state->Vpp == 120) {
+ reg |= I365_VPP1_12V;
+ puts (" 12V card found: ");
+ } else if (state->Vpp == state->Vcc) {
+ reg |= I365_VPP1_5V;
+ } else {
+ puts (" power not found: ");
+ return -1;
+ }
+ }
+ if (state->Vcc != 0) {
+ reg |= I365_VCC_5V;
+ if (state->Vcc == 33) {
+ puts (" 3.3V card found: ");
+ i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+ } else if (state->Vcc == 50) {
+ puts (" 5V card found: ");
+ i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+ } else {
+ puts (" power not found: ");
+ return -1;
+ }
+ }
+
+ if (reg != i365_get (s, I365_POWER)) {
+ reg = (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V);
+ i365_set (s, I365_POWER, reg);
+ }
+
+ return 0;
+}
+
+/*======================================================================
+
+ Generic routines to get and set controller options
+
+======================================================================*/
+
+static void get_bridge_state (socket_info_t * s)
+{
+ cirrus_get_state (s);
+ cb_get_state (s);
+}
+
+static void set_bridge_state (socket_info_t * s)
+{
+ cb_set_state (s);
+ i365_set (s, I365_GBLCTL, 0x00);
+ i365_set (s, I365_GENCTL, 0x00);
+ cirrus_set_state (s);
+}
+
+static void set_bridge_opts (socket_info_t * s)
+{
+ cirrus_set_opts (s);
+ cb_set_opts (s);
+}
+
+/*====================================================================*/
+#define PD67_EXT_INDEX 0x2e /* Extension index */
+#define PD67_EXT_DATA 0x2f /* Extension data */
+#define PD67_EXD_VS1(s) (0x01 << ((s)<<1))
+
+#define pd67_ext_get(s, r) \
+ (i365_set(s, PD67_EXT_INDEX, r), i365_get(s, PD67_EXT_DATA))
+
+static int i365_get_status (socket_info_t * s, u_int * value)
+{
+ u_int status;
+ u_char val;
+ u_char power, vcc, vpp;
+ u_int powerstate;
+
+ status = i365_get (s, I365_IDENT);
+ status = i365_get (s, I365_STATUS);
+ *value = ((status & I365_CS_DETECT) == I365_CS_DETECT) ? SS_DETECT : 0;
+ if (i365_get (s, I365_INTCTL) & I365_PC_IOCARD) {
+ *value |= (status & I365_CS_STSCHG) ? 0 : SS_STSCHG;
+ } else {
+ *value |= (status & I365_CS_BVD1) ? 0 : SS_BATDEAD;
+ *value |= (status & I365_CS_BVD2) ? 0 : SS_BATWARN;
+ }
+ *value |= (status & I365_CS_WRPROT) ? SS_WRPROT : 0;
+ *value |= (status & I365_CS_READY) ? SS_READY : 0;
+ *value |= (status & I365_CS_POWERON) ? SS_POWERON : 0;
+
+ /* Check for Cirrus CL-PD67xx chips */
+ i365_set (s, PD67_CHIP_INFO, 0);
+ val = i365_get (s, PD67_CHIP_INFO);
+ s->type = -1;
+ if ((val & PD67_INFO_CHIP_ID) == PD67_INFO_CHIP_ID) {
+ val = i365_get (s, PD67_CHIP_INFO);
+ if ((val & PD67_INFO_CHIP_ID) == 0) {
+ s->type = (val & PD67_INFO_SLOTS) ? IS_PD672X : IS_PD6710;
+ i365_set (s, PD67_EXT_INDEX, 0xe5);
+ if (i365_get (s, PD67_EXT_INDEX) != 0xe5)
+ s->type = IS_VT83C469;
+ }
+ } else {
+ printf ("no Cirrus Chip found\n");
+ *value = 0;
return -1;
}
- /* - 0xfe000000 see MPC 8245 Users Manual Adress Map B */
- membaseCsr = PCMCIA_IO_BASE - 0xfe000000;
+
+ power = i365_get (s, I365_POWER);
+ state.flags |= (power & I365_PWR_AUTO) ? SS_PWR_AUTO : 0;
+ state.flags |= (power & I365_PWR_OUT) ? SS_OUTPUT_ENA : 0;
+ vcc = power & I365_VCC_MASK;
+ vpp = power & I365_VPP1_MASK;
+ state.Vcc = state.Vpp = 0;
+ if((vcc== 0) || (vpp == 0)) {
+ /*
+ * On the Cirrus we get the info which card voltage
+ * we have in EXTERN DATA and write it to MISC_CTL1
+ */
+ powerstate = pd67_ext_get(s, PD67_EXTERN_DATA);
+ if (powerstate & PD67_EXD_VS1(0)) {
+ /* 5V Card */
+ i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+ } else {
+ /* 3.3V Card */
+ i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+ }
+ i365_set (s, I365_POWER, (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V));
+ power = i365_get (s, I365_POWER);
+ }
+ if (power & I365_VCC_5V) {
+ state.Vcc = (i365_get(s, PD67_MISC_CTL_1) & PD67_MC1_VCC_3V) ? 33 : 50;
+ }
+
+ if (power == I365_VPP1_12V)
+ state.Vpp = 120;
+
+ /* IO card, RESET flags, IO interrupt */
+ power = i365_get (s, I365_INTCTL);
+ state.flags |= (power & I365_PC_RESET) ? 0 : SS_RESET;
+ if (power & I365_PC_IOCARD)
+ state.flags |= SS_IOCARD;
+ state.io_irq = power & I365_IRQ_MASK;
+
+ /* Card status change mask */
+ power = i365_get (s, I365_CSCINT);
+ state.csc_mask = (power & I365_CSC_DETECT) ? SS_DETECT : 0;
+ if (state.flags & SS_IOCARD)
+ state.csc_mask |= (power & I365_CSC_STSCHG) ? SS_STSCHG : 0;
+ else {
+ state.csc_mask |= (power & I365_CSC_BVD1) ? SS_BATDEAD : 0;
+ state.csc_mask |= (power & I365_CSC_BVD2) ? SS_BATWARN : 0;
+ state.csc_mask |= (power & I365_CSC_READY) ? SS_READY : 0;
+ }
+ debug ("i82365: GetStatus(0) = flags %#3.3x, Vcc %d, Vpp %d, "
+ "io_irq %d, csc_mask %#2.2x\n", state.flags,
+ state.Vcc, state.Vpp, state.io_irq, state.csc_mask);
+
+ return 0;
+} /* i365_get_status */
+
+static int i365_set_socket (socket_info_t * s, socket_state_t * state)
+{
+ u_char reg;
+
+ set_bridge_state (s);
+
+ /* IO card, RESET flag */
+ reg = 0;
+ reg |= (state->flags & SS_RESET) ? 0 : I365_PC_RESET;
+ reg |= (state->flags & SS_IOCARD) ? I365_PC_IOCARD : 0;
+ i365_set (s, I365_INTCTL, reg);
+
+ cb_set_power (s, state);
+
+#if 0
+ /* Card status change interrupt mask */
+ reg = s->cs_irq << 4;
+ if (state->csc_mask & SS_DETECT)
+ reg |= I365_CSC_DETECT;
+ if (state->flags & SS_IOCARD) {
+ if (state->csc_mask & SS_STSCHG)
+ reg |= I365_CSC_STSCHG;
+ } else {
+ if (state->csc_mask & SS_BATDEAD)
+ reg |= I365_CSC_BVD1;
+ if (state->csc_mask & SS_BATWARN)
+ reg |= I365_CSC_BVD2;
+ if (state->csc_mask & SS_READY)
+ reg |= I365_CSC_READY;
+ }
+ i365_set (s, I365_CSCINT, reg);
+ i365_get (s, I365_CSC);
+#endif /* 0 */
+
+ return 0;
+} /* i365_set_socket */
+
+/*====================================================================*/
+
+static int i365_set_mem_map (socket_info_t * s, struct pccard_mem_map *mem)
+{
+ u_short base, i;
+ u_char map;
+
+ debug ("i82365: SetMemMap(%d, %#2.2x, %d ns, %#5.5lx-%#5.5lx, %#5.5x)\n",
+ mem->map, mem->flags, mem->speed,
+ mem->sys_start, mem->sys_stop, mem->card_start);
+
+ map = mem->map;
+ if ((map > 4) ||
+ (mem->card_start > 0x3ffffff) ||
+ (mem->sys_start > mem->sys_stop) ||
+ (mem->speed > 1000)) {
+ return -1;
+ }
+
+ /* Turn off the window before changing anything */
+ if (i365_get (s, I365_ADDRWIN) & I365_ENA_MEM (map))
+ i365_bclr (s, I365_ADDRWIN, I365_ENA_MEM (map));
+
+ /* Take care of high byte, for PCI controllers */
+ i365_set (s, CB_MEM_PAGE (map), mem->sys_start >> 24);
+
+ base = I365_MEM (map);
+ i = (mem->sys_start >> 12) & 0x0fff;
+ if (mem->flags & MAP_16BIT)
+ i |= I365_MEM_16BIT;
+ if (mem->flags & MAP_0WS)
+ i |= I365_MEM_0WS;
+ i365_set_pair (s, base + I365_W_START, i);
+
+ i = (mem->sys_stop >> 12) & 0x0fff;
+ switch (mem->speed / CYCLE_TIME) {
+ case 0:
+ break;
+ case 1:
+ i |= I365_MEM_WS0;
+ break;
+ case 2:
+ i |= I365_MEM_WS1;
+ break;
+ default:
+ i |= I365_MEM_WS1 | I365_MEM_WS0;
+ break;
+ }
+ i365_set_pair (s, base + I365_W_STOP, i);
+
+ i = 0;
+ if (mem->flags & MAP_WRPROT)
+ i |= I365_MEM_WRPROT;
+ if (mem->flags & MAP_ATTRIB)
+ i |= I365_MEM_REG;
+ i365_set_pair (s, base + I365_W_OFF, i);
+
+ /* set System Memory map Upper Adress */
+ i365_set(s, PD67_EXT_INDEX, PD67_MEM_PAGE(map));
+ i365_set(s, PD67_EXT_DATA, ((mem->sys_start >> 24) & 0xff));
+
+ /* Turn on the window if necessary */
+ if (mem->flags & MAP_ACTIVE)
+ i365_bset (s, I365_ADDRWIN, I365_ENA_MEM (map));
+ return 0;
+} /* i365_set_mem_map */
+
+static int i365_set_io_map (socket_info_t * s, struct pccard_io_map *io)
+{
+ u_char map, ioctl;
+
+ map = io->map;
+ /* comment out: comparison is always false due to limited range of data type */
+ if ((map > 1) || /* (io->start > 0xffff) || (io->stop > 0xffff) || */
+ (io->stop < io->start))
+ return -1;
+ /* Turn off the window before changing anything */
+ if (i365_get (s, I365_ADDRWIN) & I365_ENA_IO (map))
+ i365_bclr (s, I365_ADDRWIN, I365_ENA_IO (map));
+ i365_set_pair (s, I365_IO (map) + I365_W_START, io->start);
+ i365_set_pair (s, I365_IO (map) + I365_W_STOP, io->stop);
+ ioctl = i365_get (s, I365_IOCTL) & ~I365_IOCTL_MASK (map);
+ if (io->speed)
+ ioctl |= I365_IOCTL_WAIT (map);
+ if (io->flags & MAP_0WS)
+ ioctl |= I365_IOCTL_0WS (map);
+ if (io->flags & MAP_16BIT)
+ ioctl |= I365_IOCTL_16BIT (map);
+ if (io->flags & MAP_AUTOSZ)
+ ioctl |= I365_IOCTL_IOCS16 (map);
+ i365_set (s, I365_IOCTL, ioctl);
+ /* Turn on the window if necessary */
+ if (io->flags & MAP_ACTIVE)
+ i365_bset (s, I365_ADDRWIN, I365_ENA_IO (map));
+ return 0;
+} /* i365_set_io_map */
+
+/*====================================================================*/
+
+/*
+ * PCI_ADDR = (HOST_ADDR - 0xfe000000)
+ * see MPC 8245 Users Manual Adress Map B
+ */
+#define HOST_TO_PCI(addr) ((addr) - 0xfe000000)
+#define PCI_TO_HOST(addr) ((addr) + 0xfe000000)
+
+int i82365_init (void)
+{
+ u_int val;
+ int i;
+
+ if ((socket.dev = pci_find_devices (supported, 0)) < 0) {
+ /* Controller not found */
+ printf ("No PD67290 device found !!\n");
+ return 1;
+ }
+ debug ("i82365 Device Found!\n");
+
+ socket.cb_phys = PCMCIA_IO_BASE;
/* set base address */
- pci_write_config_dword (devno, PCI_BASE_ADDRESS_0, membaseCsr);
+ pci_write_config_dword (socket.dev, PCI_BASE_ADDRESS_0,
+ HOST_TO_PCI(socket.cb_phys));
/* enable mapped memory and IO addresses */
- pci_write_config_dword (devno,
+ pci_write_config_dword (socket.dev,
PCI_COMMAND,
PCI_COMMAND_MEMORY |
PCI_COMMAND_IO | PCI_COMMAND_WAIT);
+
+ get_bridge_state (&socket);
+ set_bridge_opts (&socket);
+
+ i = i365_get_status (&socket, &val);
+
+ if (i > -1) {
+ puts (pcic[socket.type].name);
+ } else {
+ printf ("i82365: Controller not found.\n");
+ return 1;
+ }
+ if((val & SS_DETECT) != SS_DETECT){
+ puts ("No card\n");
+ return 1;
+ }
+
+ state.flags |= SS_OUTPUT_ENA;
+
+ i365_set_socket (&socket, &state);
+
+ for (i = 500; i; i--) {
+ if ((i365_get (&socket, I365_STATUS) & I365_CS_READY))
+ break;
+ udelay (1000);
+ }
+
+ if (i == 0) {
+ /* PC Card not ready for data transfer */
+ puts ("i82365 PC Card not ready for data transfer\n");
+ return 1;
+ }
+ debug (" PC Card ready for data transfer: ");
+
+ mem.map = 0;
+ mem.flags = MAP_ATTRIB | MAP_ACTIVE;
+ mem.speed = 300;
+ mem.sys_start = CFG_PCMCIA_MEM_ADDR;
+ mem.sys_stop = CFG_PCMCIA_MEM_ADDR + CFG_PCMCIA_MEM_SIZE - 1;
+ mem.card_start = 0;
+ i365_set_mem_map (&socket, &mem);
+
+ mem.map = 1;
+ mem.flags = MAP_ACTIVE;
+ mem.speed = 300;
+ mem.sys_start = CFG_PCMCIA_MEM_ADDR + CFG_PCMCIA_MEM_SIZE;
+ mem.sys_stop = CFG_PCMCIA_MEM_ADDR + (2 * CFG_PCMCIA_MEM_SIZE) - 1;
+ mem.card_start = 0;
+ i365_set_mem_map (&socket, &mem);
+
+#ifdef DEBUG
+ i82365_dump_regions (socket.dev);
+#endif
+
return 0;
}
+
+void i82365_exit (void)
+{
+ io.map = 0;
+ io.flags = 0;
+ io.speed = 0;
+ io.start = 0;
+ io.stop = 0x1;
+
+ i365_set_io_map (&socket, &io);
+
+ mem.map = 0;
+ mem.flags = 0;
+ mem.speed = 0;
+ mem.sys_start = 0;
+ mem.sys_stop = 0x1000;
+ mem.card_start = 0;
+
+ i365_set_mem_map (&socket, &mem);
+
+ mem.map = 1;
+ mem.flags = 0;
+ mem.speed = 0;
+ mem.sys_start = 0;
+ mem.sys_stop = 0x1000;
+ mem.card_start = 0;
+
+ i365_set_mem_map (&socket, &mem);
+
+ state.Vcc = state.Vpp = 0;
+
+ i365_set_socket (&socket, &state);
+}
+
+int pcmcia_on (void)
+{
+ u_int rc;
+
+ debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+ rc = i82365_init();
+ if (rc)
+ goto exit;
+
+ rc = check_ide_device(0);
+ if (rc == 0)
+ goto exit;
+
+ i82365_exit();
+
+exit:
+ return rc;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_off (void)
+{
+ printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+ i82365_exit();
+
+ return 0;
+}
+#endif
+
+/*======================================================================
+
+ Debug stuff
+
+======================================================================*/
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev)
+{
+ u_int tmp[2];
+ u_int *mem = (void *) socket.cb_phys;
+ u_char *cis = (void *) CFG_PCMCIA_MEM_ADDR;
+ u_char *ide = (void *) (CFG_ATA_BASE_ADDR + CFG_ATA_REG_OFFSET);
+
+ pci_read_config_dword (dev, 0x00, tmp + 0);
+ pci_read_config_dword (dev, 0x80, tmp + 1);
+
+ printf ("PCI CONF: %08X ... %08X\n",
+ tmp[0], tmp[1]);
+ printf ("PCI MEM: ... %08X ... %08X\n",
+ mem[0x8 / 4], mem[0x800 / 4]);
+ printf ("CIS: ...%c%c%c%c%c%c%c%c...\n",
+ cis[0x38], cis[0x3a], cis[0x3c], cis[0x3e],
+ cis[0x40], cis[0x42], cis[0x44], cis[0x48]);
+ printf ("CIS CONF: %02X %02X %02X ...\n",
+ cis[0x200], cis[0x202], cis[0x204]);
+ printf ("IDE: %02X %02X %02X %02X %02X %02X %02X %02X\n",
+ ide[0], ide[1], ide[2], ide[3],
+ ide[4], ide[5], ide[6], ide[7]);
+}
+#endif /* DEBUG */
+
+#endif /* CONFIG_I82365 */
diff --git a/board/cpu87/cpu87.c b/board/cpu87/cpu87.c
index 8363d86..e8c2614 100644
--- a/board/cpu87/cpu87.c
+++ b/board/cpu87/cpu87.c
@@ -197,7 +197,7 @@
*/
int checkboard (void)
{
- printf ("Board: CPU87 (Rev %02x)\n", CPU86_REV);
+ printf ("Board: CPU87 (Rev %02x)\n", CPU86_REV & 0x7f);
return 0;
}
@@ -280,7 +280,7 @@
volatile memctl8260_t *memctl = &immap->im_memctl;
#ifndef CFG_RAMBOOT
- ulong size8, size9;
+ ulong size8, size9, size10;
#endif
long psize;
@@ -294,17 +294,25 @@
*/
size8 = try_init (memctl, CFG_PSDMR_8COL, CFG_OR2_8COL,
(uchar *) CFG_SDRAM_BASE);
+
size9 = try_init (memctl, CFG_PSDMR_9COL, CFG_OR2_9COL,
(uchar *) CFG_SDRAM_BASE);
-
- if (size8 < size9) {
- psize = size9;
- printf ("(60x:9COL) ");
- } else {
+
+ size10 = try_init (memctl, CFG_PSDMR_10COL, CFG_OR2_10COL,
+ (uchar *) CFG_SDRAM_BASE);
+
+ psize = max(size8,max(size9,size10));
+
+ if (psize == size8) {
psize = try_init (memctl, CFG_PSDMR_8COL, CFG_OR2_8COL,
(uchar *) CFG_SDRAM_BASE);
printf ("(60x:8COL) ");
- }
+ } else if (psize == size9){
+ psize = try_init (memctl, CFG_PSDMR_9COL, CFG_OR2_9COL,
+ (uchar *) CFG_SDRAM_BASE);
+ printf ("(60x:9COL) ");
+ } else
+ printf ("(60x:10COL) ");
#endif /* CFG_RAMBOOT */
diff --git a/board/etin/kvme080/Makefile b/board/etin/kvme080/Makefile
new file mode 100644
index 0000000..303ccfa
--- /dev/null
+++ b/board/etin/kvme080/Makefile
@@ -0,0 +1,40 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = lib$(BOARD).a
+
+OBJS = $(BOARD).o multiverse.o
+
+$(LIB): .depend $(OBJS)
+ $(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend: Makefile $(OBJS:.o=.c)
+ $(CC) -M $(CFLAGS) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################
diff --git a/board/etin/kvme080/config.mk b/board/etin/kvme080/config.mk
new file mode 100644
index 0000000..45abdc0
--- /dev/null
+++ b/board/etin/kvme080/config.mk
@@ -0,0 +1,30 @@
+#
+# (C) Copyright 2005
+# Sangmoon, Etin Systems, dogoil@etinsys.com.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# KVME080 board
+#
+
+TEXT_BASE = 0xFFF00000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE)
diff --git a/board/etin/kvme080/kvme080.c b/board/etin/kvme080/kvme080.c
new file mode 100644
index 0000000..de62fa0
--- /dev/null
+++ b/board/etin/kvme080/kvme080.c
@@ -0,0 +1,193 @@
+/*
+ * (C) Copyright 2005
+ * Sangmoon Kim, Etin Systems. dogoil@etinsys.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc824x.h>
+#include <pci.h>
+#include <i2c.h>
+#include <asm/processor.h>
+
+int checkboard(void)
+{
+ puts ("Board: KVME080\n");
+ return 0;
+}
+
+unsigned long setdram(int m, int row, int col, int bank)
+{
+ int i;
+ unsigned long start, end;
+ uint32_t mccr1;
+ uint32_t mear1 = 0, emear1 = 0, msar1 = 0, emsar1 = 0;
+ uint32_t mear2 = 0, emear2 = 0, msar2 = 0, emsar2 = 0;
+ uint8_t mber = 0;
+
+ CONFIG_READ_WORD(MCCR1, mccr1);
+ mccr1 &= 0xffff0000;
+
+ start = CFG_SDRAM_BASE;
+ end = start + (1 << (col + row + 3) ) * bank - 1;
+
+ for (i = 0; i < m; i++) {
+ mccr1 |= ((row == 13)? 2 : (bank == 4)? 0 : 3) << i * 2;
+ if (i < 4) {
+ msar1 |= ((start >> 20) & 0xff) << i * 8;
+ emsar1 |= ((start >> 28) & 0xff) << i * 8;
+ mear1 |= ((end >> 20) & 0xff) << i * 8;
+ emear1 |= ((end >> 28) & 0xff) << i * 8;
+ } else {
+ msar2 |= ((start >> 20) & 0xff) << (i-4) * 8;
+ emsar2 |= ((start >> 28) & 0xff) << (i-4) * 8;
+ mear2 |= ((end >> 20) & 0xff) << (i-4) * 8;
+ emear2 |= ((end >> 28) & 0xff) << (i-4) * 8;
+ }
+ mber |= 1 << i;
+ start += (1 << (col + row + 3) ) * bank;
+ end += (1 << (col + row + 3) ) * bank;
+ }
+ for (; i < 8; i++) {
+ if (i < 4) {
+ msar1 |= 0xff << i * 8;
+ emsar1 |= 0x30 << i * 8;
+ mear1 |= 0xff << i * 8;
+ emear1 |= 0x30 << i * 8;
+ } else {
+ msar2 |= 0xff << (i-4) * 8;
+ emsar2 |= 0x30 << (i-4) * 8;
+ mear2 |= 0xff << (i-4) * 8;
+ emear2 |= 0x30 << (i-4) * 8;
+ }
+ }
+
+ CONFIG_WRITE_WORD(MCCR1, mccr1);
+ CONFIG_WRITE_WORD(MSAR1, msar1);
+ CONFIG_WRITE_WORD(EMSAR1, emsar1);
+ CONFIG_WRITE_WORD(MEAR1, mear1);
+ CONFIG_WRITE_WORD(EMEAR1, emear1);
+ CONFIG_WRITE_WORD(MSAR2, msar2);
+ CONFIG_WRITE_WORD(EMSAR2, emsar2);
+ CONFIG_WRITE_WORD(MEAR2, mear2);
+ CONFIG_WRITE_WORD(EMEAR2, emear2);
+ CONFIG_WRITE_BYTE(MBER, mber);
+
+ return (1 << (col + row + 3) ) * bank * m;
+}
+
+long int initdram(int board_type)
+{
+ unsigned int msr;
+ long int size = 0;
+
+ msr = mfmsr();
+ mtmsr(msr & ~(MSR_IR | MSR_DR));
+ mtspr(IBAT2L, CFG_IBAT0L + 0x10000000);
+ mtspr(IBAT2U, CFG_IBAT0U + 0x10000000);
+ mtspr(DBAT2L, CFG_DBAT0L + 0x10000000);
+ mtspr(DBAT2U, CFG_DBAT0U + 0x10000000);
+ mtmsr(msr);
+
+ if (setdram(2,13,10,4) == get_ram_size(CFG_SDRAM_BASE, 0x20000000))
+ size = 0x20000000; /* 512MB */
+ else if (setdram(1,13,10,4) == get_ram_size(CFG_SDRAM_BASE, 0x10000000))
+ size = 0x10000000; /* 256MB */
+ else if (setdram(2,13,9,4) == get_ram_size(CFG_SDRAM_BASE, 0x10000000))
+ size = 0x10000000; /* 256MB */
+ else if (setdram(1,13,9,4) == get_ram_size(CFG_SDRAM_BASE, 0x08000000))
+ size = 0x08000000; /* 128MB */
+ else if (setdram(2,12,9,4) == get_ram_size(CFG_SDRAM_BASE, 0x08000000))
+ size = 0x08000000; /* 128MB */
+ else if (setdram(1,12,9,4) == get_ram_size(CFG_SDRAM_BASE, 0x04000000))
+ size = 0x04000000; /* 64MB */
+
+ msr = mfmsr();
+ mtmsr(msr & ~(MSR_IR | MSR_DR));
+ mtspr(IBAT2L, CFG_IBAT2L);
+ mtspr(IBAT2U, CFG_IBAT2U);
+ mtspr(DBAT2L, CFG_DBAT2L);
+ mtspr(DBAT2U, CFG_DBAT2U);
+ mtmsr(msr);
+
+ return size;
+}
+
+struct pci_controller hose;
+
+void pci_init_board(void)
+{
+ pci_mpc824x_init(&hose);
+}
+
+int board_early_init_f(void)
+{
+ *(volatile unsigned char *)(0xff080120) = 0xfb;
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ unsigned int msr;
+
+ CONFIG_WRITE_WORD(ERCR1, 0x95ff8000);
+ CONFIG_WRITE_WORD(ERCR3, 0x0c00000e);
+ CONFIG_WRITE_WORD(ERCR4, 0x0800000e);
+
+ msr = mfmsr();
+ mtmsr(msr & ~(MSR_IR | MSR_DR));
+ mtspr(IBAT1L, 0x70000000 | BATL_PP_10 | BATL_CACHEINHIBIT);
+ mtspr(IBAT1U, 0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP);
+ mtspr(DBAT1L, 0x70000000 | BATL_PP_10 | BATL_CACHEINHIBIT);
+ mtspr(DBAT1U, 0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP);
+ mtmsr(msr);
+
+ return 0;
+}
+
+extern int multiverse_init(void);
+
+int misc_init_r(void)
+{
+ multiverse_init();
+ return 0;
+}
+
+void *nvram_read(void *dest, const long src, size_t count)
+{
+ volatile uchar *d = (volatile uchar*) dest;
+ volatile uchar *s = (volatile uchar*) src;
+ while(count--) {
+ *d++ = *s++;
+ asm volatile("sync");
+ }
+ return dest;
+}
+
+void nvram_write(long dest, const void *src, size_t count)
+{
+ volatile uchar *d = (volatile uchar*)dest;
+ volatile uchar *s = (volatile uchar*)src;
+ while(count--) {
+ *d++ = *s++;
+ asm volatile("sync");
+ }
+}
diff --git a/board/etin/kvme080/multiverse.c b/board/etin/kvme080/multiverse.c
new file mode 100644
index 0000000..eb89581
--- /dev/null
+++ b/board/etin/kvme080/multiverse.c
@@ -0,0 +1,186 @@
+/*
+ * multiverse.c
+ *
+ * VME driver for Multiverse
+ *
+ * Author : Sangmoon Kim
+ * dogoil@etinsys.com
+ *
+ * Copyright 2005 ETIN SYSTEMS Co.,Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <pci.h>
+
+#include "multiverse.h"
+
+static unsigned long vme_asi_addr;
+static unsigned long vme_iack_addr;
+static unsigned long pci_reg_addr;
+static unsigned long vme_reg_addr;
+
+int multiv_reset(unsigned long base)
+{
+ writeb(0x09, base + VME_SLAVE32_AM);
+ writeb(0x39, base + VME_SLAVE24_AM);
+ writeb(0x29, base + VME_SLAVE16_AM);
+ writeb(0x2f, base + VME_SLAVE_REG_AM);
+ writeb((VME_A32_SLV_BUS >> 24) & 0xff, base + VME_SLAVE32_A);
+ writeb((VME_A24_SLV_BUS >> 16) & 0xff, base + VME_SLAVE24_A);
+ writeb((VME_A16_SLV_BUS >> 8 ) & 0xff, base + VME_SLAVE16_A);
+#ifdef A32_SLV_WINDOW
+ if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+ writeb(((~(VME_A32_SLV_SIZE-1)) >> 24) & 0xff,
+ base + VME_SLAVE32_MASK);
+ writeb(0x01, base + VME_SLAVE32_EN);
+ } else {
+ writeb(0xff, base + VME_SLAVE32_MASK);
+ writeb(0x00, base + VME_SLAVE32_EN);
+ }
+#else
+ writeb(0xff, base + VME_SLAVE32_MASK);
+ writeb(0x00, base + VME_SLAVE32_EN);
+#endif
+#ifdef A24_SLV_WINDOW
+ if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+ writeb(((~(VME_A24_SLV_SIZE-1)) >> 16) & 0xff,
+ base + VME_SLAVE24_MASK);
+ writeb(0x01, base + VME_SLAVE24_EN);
+ } else {
+ writeb(0xff, base + VME_SLAVE24_MASK);
+ writeb(0x00, base + VME_SLAVE24_EN);
+ }
+#else
+ writeb(0xff, base + VME_SLAVE24_MASK);
+ writeb(0x00, base + VME_SLAVE24_EN);
+#endif
+#ifdef A16_SLV_WINDOW
+ if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+ writeb(((~(VME_A16_SLV_SIZE-1)) >> 8) & 0xff,
+ base + VME_SLAVE16_MASK);
+ writeb(0x01, base + VME_SLAVE16_EN);
+ } else {
+ writeb(0xff, base + VME_SLAVE16_MASK);
+ writeb(0x00, base + VME_SLAVE16_EN);
+ }
+#else
+ writeb(0xff, base + VME_SLAVE16_MASK);
+ writeb(0x00, base + VME_SLAVE16_EN);
+#endif
+#ifdef REG_SLV_WINDOW
+ if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+ writeb(((~(VME_REG_SLV_SIZE-1)) >> 16) & 0xff,
+ base + VME_SLAVE_REG_MASK);
+ writeb(0x01, base + VME_SLAVE_REG_EN);
+ } else {
+ writeb(0xf8, base + VME_SLAVE_REG_MASK);
+ }
+#else
+ writeb(0xf8, base + VME_SLAVE_REG_MASK);
+#endif
+ writeb(0x09, base + VME_MASTER32_AM);
+ writeb(0x39, base + VME_MASTER24_AM);
+ writeb(0x29, base + VME_MASTER16_AM);
+ writeb(0x2f, base + VME_MASTER_REG_AM);
+ writel(0x00000000, base + VME_RMW_ADRS);
+ writeb(0x00, base + VME_IRQ);
+ writeb(0x00, base + VME_INT_EN);
+ writel(0x00000000, base + VME_IRQ1_REG);
+ writel(0x00000000, base + VME_IRQ2_REG);
+ writel(0x00000000, base + VME_IRQ3_REG);
+ writel(0x00000000, base + VME_IRQ4_REG);
+ writel(0x00000000, base + VME_IRQ5_REG);
+ writel(0x00000000, base + VME_IRQ6_REG);
+ writel(0x00000000, base + VME_IRQ7_REG);
+ return 0;
+}
+
+void multiv_auto_slot_id(unsigned long base)
+{
+ unsigned int vector;
+ int slot_id = 1;
+ if (readb(base + VME_CTRL) & VME_CTRL_SYSFAIL) {
+ *(volatile unsigned int*)(base + VME_IRQ2_REG) = 0xfe;
+ writeb(readb(base + VME_IRQ) | 0x04, base + VME_IRQ);
+ writeb(readb(base + VME_CTRL) & ~VME_CTRL_SYSFAIL,
+ base + VME_CTRL);
+ while (readb(base + VME_STATUS) & VME_STATUS_SYSFAIL);
+ if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+ while (readb(base + VME_INT) & 0x04) {
+ vector = *(volatile unsigned int*)
+ (vme_iack_addr + VME_IACK2);
+ *(unsigned char*)(vme_asi_addr + 0x7ffff)
+ = (slot_id << 3) & 0xff;
+ slot_id ++;
+ if (slot_id > 31)
+ break;
+ }
+ }
+ }
+}
+
+int multiverse_init(void)
+{
+ int i;
+ pci_dev_t pdev;
+ unsigned int bar[6];
+
+ pdev = pci_find_device(0x1895, 0x0001, 0);
+
+ if (pdev == 0)
+ return -1;
+
+ for (i = 0; i < 6; i++)
+ pci_read_config_dword (pdev,
+ PCI_BASE_ADDRESS_0 + i * 4, &bar[i]);
+
+ pci_reg_addr = bar[0];
+ vme_reg_addr = bar[1] + 0x00F00000;
+ vme_iack_addr = bar[1] + 0x00200000;
+ vme_asi_addr = bar[3];
+
+ pci_write_config_dword (pdev, PCI_COMMAND,
+ PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+ writel(0xFF000000, pci_reg_addr + P_TA1);
+ writel(0x04, pci_reg_addr + P_IMG_CTRL1);
+ writel(0xf0000000, pci_reg_addr + P_TA2);
+ writel(0x04, pci_reg_addr + P_IMG_CTRL2);
+ writel(0xF1000000, pci_reg_addr + P_TA3);
+ writel(0x04, pci_reg_addr + P_IMG_CTRL3);
+ writel(VME_A32_MSTR_BUS, pci_reg_addr + P_TA5);
+ writel(~(VME_A32_MSTR_SIZE-1), pci_reg_addr + P_AM5);
+ writel(0x04, pci_reg_addr + P_IMG_CTRL5);
+
+ writel(VME_A32_SLV_BUS, pci_reg_addr + W_BA1);
+ writel(~(VME_A32_SLV_SIZE-1), pci_reg_addr + W_AM1);
+ writel(VME_A32_SLV_LOCAL, pci_reg_addr + W_TA1);
+ writel(0x04, pci_reg_addr + W_IMG_CTRL1);
+
+ writel(0xF0000000, pci_reg_addr + W_BA2);
+ writel(0xFF000000, pci_reg_addr + W_AM2);
+ writel(VME_A24_SLV_LOCAL, pci_reg_addr + W_TA2);
+ writel(0x04, pci_reg_addr + W_IMG_CTRL2);
+
+ writel(0xFF000000, pci_reg_addr + W_BA3);
+ writel(0xFF000000, pci_reg_addr + W_AM3);
+ writel(VME_A16_SLV_LOCAL, pci_reg_addr + W_TA3);
+ writel(0x04, pci_reg_addr + W_IMG_CTRL3);
+
+ writel(0x00000001, pci_reg_addr + W_ERR_CS);
+ writel(0x00000001, pci_reg_addr + P_ERR_CS);
+
+ multiv_reset(vme_reg_addr);
+ writeb(readb(vme_reg_addr + VME_CTRL) | VME_CTRL_SHORT_D,
+ vme_reg_addr + VME_CTRL);
+
+ multiv_auto_slot_id(vme_reg_addr);
+
+ return 0;
+}
diff --git a/board/etin/kvme080/multiverse.h b/board/etin/kvme080/multiverse.h
new file mode 100644
index 0000000..776162d
--- /dev/null
+++ b/board/etin/kvme080/multiverse.h
@@ -0,0 +1,176 @@
+/*
+ * multiverse.h
+ *
+ * VME driver for Multiverse
+ *
+ * Author : Sangmoon Kim
+ * dogoil@etinsys.com
+ *
+ * Copyright 2005 ETIN SYSTEMS Co.,Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __MULTIVERSE_H__
+#define __MULTIVERSE_H__
+
+#define VME_A32_MSTR_BUS 0x90000000
+#define VME_A32_MSTR_SIZE 0x01000000
+
+#define VME_A32_SLV_SIZE 0x01000000
+
+#define VME_A32_SLV_BUS 0x90000000
+#define VME_A24_SLV_BUS 0x00000000
+#define VME_A16_SLV_BUS 0x00000000
+
+#define VME_A32_SLV_LOCAL 0x00000000
+#define VME_A24_SLV_LOCAL 0x00000000
+#define VME_A16_SLV_LOCAL 0x00000000
+
+#define A32_SLV_WINDOW
+#undef A24_SLV_WINDOW
+#undef A16_SLV_WINDOW
+#undef REG_SLV_WINDOW
+
+/* PCI Registers */
+
+#define P_IMG_CTRL0 0x100
+#define P_BA0 0x104
+#define P_AM0 0x108
+#define P_TA0 0x10C
+#define P_IMG_CTRL1 0x110
+#define P_BA1 0x114
+#define P_AM1 0x118
+#define P_TA1 0x11C
+#define P_IMG_CTRL2 0x120
+#define P_BA2 0x124
+#define P_AM2 0x128
+#define P_TA2 0x12C
+#define P_IMG_CTRL3 0x130
+#define P_BA3 0x134
+#define P_AM3 0x138
+#define P_TA3 0x13C
+#define P_IMG_CTRL4 0x140
+#define P_BA4 0x144
+#define P_AM4 0x148
+#define P_TA4 0x14C
+#define P_IMG_CTRL5 0x150
+#define P_BA5 0x154
+#define P_AM5 0x158
+#define P_TA5 0x15C
+#define P_ERR_CS 0x160
+#define P_ERR_ADDR 0x164
+#define P_ERR_DATA 0x168
+
+#define WB_CONF_SPC_BAR 0x180
+#define W_IMG_CTRL1 0x184
+#define W_BA1 0x188
+#define W_AM1 0x18C
+#define W_TA1 0x190
+#define W_IMG_CTRL2 0x194
+#define W_BA2 0x198
+#define W_AM2 0x19C
+#define W_TA2 0x1A0
+#define W_IMG_CTRL3 0x1A4
+#define W_BA3 0x1A8
+#define W_AM3 0x1AC
+#define W_TA3 0x1B0
+#define W_IMG_CTRL4 0x1B4
+#define W_BA4 0x1B8
+#define W_AM4 0x1BC
+#define W_TA4 0x1C0
+#define W_IMG_CTRL5 0x1C4
+#define W_BA5 0x1C8
+#define W_AM5 0x1CC
+#define W_TA5 0x1D0
+#define W_ERR_CS 0x1D4
+#define W_ERR_ADDR 0x1D8
+#define W_ERR_DATA 0x1DC
+#define CNF_ADDR 0x1E0
+#define CNF_DATA 0x1E4
+#define INT_ACK 0x1E8
+#define ICR 0x1EC
+#define ISR 0x1F0
+
+/* VME registers */
+
+#define VME_SLAVE32_AM 0x03
+#define VME_SLAVE24_AM 0x02
+#define VME_SLAVE16_AM 0x01
+#define VME_SLAVE_REG_AM 0x00
+#define VME_SLAVE32_A 0x07
+#define VME_SLAVE24_A 0x06
+#define VME_SLAVE16_A 0x05
+#define VME_SLAVE_REG_A 0x04
+#define VME_SLAVE32_MASK 0x0B
+#define VME_SLAVE24_MASK 0x0A
+#define VME_SLAVE16_MASK 0x09
+#define VME_SLAVE_REG_MASK 0x08
+#define VME_SLAVE32_EN 0x0F
+#define VME_SLAVE24_EN 0x0E
+#define VME_SLAVE16_EN 0x0D
+#define VME_SLAVE_REG_EN 0x0C
+#define VME_MASTER32_AM 0x13
+#define VME_MASTER24_AM 0x12
+#define VME_MASTER16_AM 0x11
+#define VME_MASTER_REG_AM 0x10
+#define VME_RMW_ADRS 0x14
+#define VME_MBOX 0x18
+#define VME_STATUS 0x1E
+#define VME_CTRL 0x1C
+#define VME_IRQ 0x20
+#define VME_INT_EN 0x21
+#define VME_INT 0x22
+#define VME_IRQ1_REG 0x24
+#define VME_IRQ2_REG 0x28
+#define VME_IRQ3_REG 0x2C
+#define VME_IRQ4_REG 0x30
+#define VME_IRQ5_REG 0x34
+#define VME_IRQ6_REG 0x38
+#define VME_IRQ7_REG 0x3C
+
+/* VME control register */
+
+#define VME_CTRL_BRDRST 0x01
+#define VME_CTRL_SYSRST 0x02
+#define VME_CTRL_RMW 0x04
+#define VME_CTRL_SHORT_D 0x08
+#define VME_CTRL_SYSFAIL 0x10
+#define VME_CTRL_VOWN 0x20
+#define VME_CTRL_A16_REG_MODE 0x40
+
+/* VME status register */
+
+#define VME_STATUS_SYSCON 0x01
+#define VME_STATUS_SYSFAIL 0x02
+#define VME_STATUS_ACFAIL 0x04
+#define VME_STATUS_SYSRST 0x08
+#define VME_STATUS_VOWN 0x10
+
+/* Interrupt types */
+
+#define LVL1 0x0002
+#define LVL2 0x0004
+#define LVL3 0x0008
+#define LVL4 0x0010
+#define LVL5 0x0020
+#define LVL6 0x0040
+#define LVL7 0x0080
+#define MULTIVERSE_INTI_INT 0x0100
+#define MULTIVERSE_WB_INT 0x0200
+#define MULTIVERSE_PCI_INT 0x0400
+
+/* interrupt acknowledge */
+
+#define VME_IACK1 0x04
+#define VME_IACK2 0x08
+#define VME_IACK3 0x0c
+#define VME_IACK4 0x10
+#define VME_IACK5 0x14
+#define VME_IACK6 0x18
+#define VME_IACK7 0x1c
+
+#endif /* __MULTIVERSE_H__ */
diff --git a/board/etin/kvme080/u-boot.lds b/board/etin/kvme080/u-boot.lds
new file mode 100644
index 0000000..dda3687
--- /dev/null
+++ b/board/etin/kvme080/u-boot.lds
@@ -0,0 +1,128 @@
+/*
+ * (C) Copyright 2001-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/mpc824x/start.o (.text)
+ lib_ppc/board.o (.text)
+ lib_ppc/ppcstring.o (.text)
+
+ . = DEFINED(env_offset) ? env_offset : .;
+ common/environment.o (.text)
+
+ *(.text)
+
+ *(.fixup)
+ *(.got1)
+ . = ALIGN(16);
+ *(.rodata)
+ *(.rodata1)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x0FFF) & 0xFFFFF000;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+ __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(4096);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(4096);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+
+ _end = . ;
+ PROVIDE (end = .);
+}
diff --git a/board/fads/Makefile b/board/fads/Makefile
index baa6c2e..7fc88ee 100644
--- a/board/fads/Makefile
+++ b/board/fads/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o lamp.o
+OBJS = $(BOARD).o flash.o lamp.o pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/fads/fads.h b/board/fads/fads.h
index e981be0..41f18b5 100644
--- a/board/fads/fads.h
+++ b/board/fads/fads.h
@@ -467,7 +467,9 @@
#define CONFIG_ISO_PARTITION 1
#undef CONFIG_ATAPI
+#if 0 /* does not make sense when CFG_CMD_IDE is not enabled, too */
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+#endif
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
diff --git a/board/fads/pcmcia.c b/board/fads/pcmcia.c
new file mode 100644
index 0000000..978c16b
--- /dev/null
+++ b/board/fads/pcmcia.c
@@ -0,0 +1,84 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+#ifdef CONFIG_ADS
+#define PCMCIA_BOARD_MSG "ADS"
+#else
+#define PCMCIA_BOARD_MSG "FADS"
+#endif
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+ u_long reg = 0;
+
+ switch(vpp) {
+ case 0: reg = 0; break;
+ case 50: reg = 1; break;
+ case 120: reg = 2; break;
+ default: return 1;
+ }
+
+ switch(vcc) {
+ case 0: reg = 0; break;
+#ifdef CONFIG_ADS
+ case 50: reg = BCSR1_PCCVCCON; break;
+#endif
+#ifdef CONFIG_FADS
+ case 33: reg = BCSR1_PCCVCC0 | BCSR1_PCCVCC1; break;
+ case 50: reg = BCSR1_PCCVCC1; break;
+#endif
+ default: return 1;
+ }
+
+ /* first, turn off all power */
+
+#ifdef CONFIG_ADS
+ *((uint *)BCSR1) |= BCSR1_PCCVCCON;
+#endif
+#ifdef CONFIG_FADS
+ *((uint *)BCSR1) &= ~(BCSR1_PCCVCC0 | BCSR1_PCCVCC1);
+#endif
+ *((uint *)BCSR1) &= ~BCSR1_PCCVPP_MASK;
+
+ /* enable new powersettings */
+
+#ifdef CONFIG_ADS
+ *((uint *)BCSR1) &= ~reg;
+#endif
+#ifdef CONFIG_FADS
+ *((uint *)BCSR1) |= reg;
+#endif
+
+ *((uint *)BCSR1) |= reg << 20;
+
+ return 0;
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+ *((uint *)BCSR1) &= ~BCSR1_PCCEN;
+ return 0;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ *((uint *)BCSR1) &= ~BCSR1_PCCEN;
+ return 0;
+}
+#endif /* CFG_CMD_PCMCIA */
+
+#endif /* CONFIG_PCMCIA */
diff --git a/board/gth/Makefile b/board/gth/Makefile
index e14c12e..48f74cd 100644
--- a/board/gth/Makefile
+++ b/board/gth/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o ee_access.o
+OBJS = $(BOARD).o flash.o ee_access.o pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/gth/pcmcia.c b/board/gth/pcmcia.c
new file mode 100644
index 0000000..fce5492
--- /dev/null
+++ b/board/gth/pcmcia.c
@@ -0,0 +1,93 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "GTH COMPACT FLASH"
+
+int pcmcia_voltage_set (int slot, int vcc, int vpp)
+{ /* Do nothing */
+ return 0;
+}
+
+int pcmcia_hardware_enable (int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ volatile sysconf8xx_t *sysp;
+ uint reg, mask;
+
+ debug ("hardware_enable: GTH Slot %c\n", 'A' + slot);
+
+ immap = (immap_t *) CFG_IMMR;
+ sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
+ pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
+ pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX (_slot_) = reg;
+ udelay (500);
+
+ /*
+ * Make sure there is a card in the slot,
+ * then configure the interface.
+ */
+ udelay (10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n",
+ __LINE__, __FUNCTION__,
+ &(pcmp->pcmc_pipr), pcmp->pcmc_pipr);
+ if (pcmp->pcmc_pipr & 0x98000000) {
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ mask = PCMCIA_VS1 (slot) | PCMCIA_VS2 (slot);
+ reg = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+ reg,
+ (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
+ (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
+
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX (_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX (_slot_) = reg;
+
+ udelay (250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return 0;
+}
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ return 0; /* No hardware to disable */
+}
+#endif
+
+#endif /* CONFIG_PCMCIA */
diff --git a/board/gth2/config.mk b/board/gth2/config.mk
index 6d21ba1..2bc1338 100644
--- a/board/gth2/config.mk
+++ b/board/gth2/config.mk
@@ -39,4 +39,3 @@
endif
endif
endif
-
diff --git a/board/gth2/ee_access.c b/board/gth2/ee_access.c
index e293139..d4798c4 100644
--- a/board/gth2/ee_access.c
+++ b/board/gth2/ee_access.c
@@ -8,7 +8,7 @@
For documentaion, see data sheet for DS2438, 2438.pdf
By Thomas.Lange@corelatus.com 001025
-
+
Copyright (C) 2000-2005 Corelatus AB */
/* This program is free software; you can redistribute it and/or
@@ -105,7 +105,7 @@
/* Compute a new checksum with new byte, using previous checksum as input
See DS app note 17, understanding and using cyclic redundancy checks...
Also see DS2438, page 11 */
- return( crc_lookup[Old_crc ^ New_value ]);
+ return( crc_lookup[Old_crc ^ New_value ]);
}
int ee_crc_ok( u8 *Buffer, int Len, u8 Crc ){
@@ -119,16 +119,16 @@
Curr_byte++;
}
E_DEBUG("Calculated CRC = 0x%x, read = 0x%x\n", Curr_crc, Crc);
-
+
if(Curr_crc == Crc){
- /* Good */
+ /* Good */
return(TRUE);
}
printk(KERN_ERR"EE checksum error, Calculated CRC = 0x%x, read = 0x%x\n", Curr_crc, Crc);
return(FALSE);
}
-static void
+static void
set_idle(void){
/* Send idle and keep start time
Continous 1 is idle */
@@ -136,7 +136,7 @@
}
-static int
+static int
do_cpu_reset(void){
/* Release reset and verify that chip responds with presence pulse */
int Retries=0;
@@ -146,10 +146,10 @@
/* Send reset */
WRITE_PORT(0);
udelay(RESET_LOW_TIME);
-
+
/* Release reset */
WRITE_PORT(1);
-
+
/* Wait for EEPROM to drive output */
udelay(PRESENCE_TIMEOUT);
if(!READ_PORT){
@@ -166,17 +166,17 @@
}
printk(KERN_ERR"eeprom did not respond when releasing reset\n");
-
+
/* Make sure chip releases pin */
udelay(PRESENCE_LOW_TIME);
/* Set to idle again */
set_idle();
-
+
return(-EIO);
}
-static u8
+static u8
read_cpu_byte(void){
/* Read a single byte from EEPROM
Read LSb first */
@@ -186,36 +186,36 @@
u32 Flags;
E_DEBUG("Reading byte\n");
-
+
for(i=0;i<8;i++){
/* Small delay between pulses */
udelay(1);
-#ifdef __KERNEL__
- /* Disable irq */
+#ifdef __KERNEL__
+ /* Disable irq */
save_flags(Flags);
cli();
-#endif
+#endif
/* Pull down pin short time to start read
See page 26 in data sheet */
-
+
WRITE_PORT(0);
udelay(READ_LOW);
WRITE_PORT(1);
-
+
/* Wait for chip to drive pin */
udelay(READ_TIMEOUT);
-
+
Value = READ_PORT;
if(Value)
Value=1;
#ifdef __KERNEL__
- /* Enable irq */
+ /* Enable irq */
restore_flags(Flags);
#endif
-
+
/* Wait for chip to release pin */
udelay(TOTAL_READ_LOW-READ_TIMEOUT);
@@ -230,30 +230,30 @@
return(Result);
}
-static void
+static void
write_cpu_byte(u8 Byte){
/* Write a single byte to EEPROM
Write LSb first */
int i;
int Value;
u32 Flags;
-
+
E_DEBUG("Writing byte 0x%x\n",Byte);
-
+
for(i=0;i<8;i++){
/* Small delay between pulses */
udelay(1);
Value = Byte&1;
-
+
#ifdef __KERNEL__
- /* Disable irq */
+ /* Disable irq */
save_flags(Flags);
cli();
-#endif
+#endif
/* Pull down pin short time for a 1, long time for a 0
See page 26 in data sheet */
-
+
WRITE_PORT(0);
if(Value){
/* Write a 1 */
@@ -267,54 +267,54 @@
WRITE_PORT(1);
#ifdef __KERNEL__
- /* Enable irq */
+ /* Enable irq */
restore_flags(Flags);
#endif
if(Value)
/* Wait for chip to read the 1 */
udelay(TOTAL_WRITE_LOW-WRITE_1_LOW);
-
+
/* E_DEBUG("Wrote %d\n",Value); */
Byte>>=1;
}
}
int ee_do_cpu_command( u8 *Tx, int Tx_len, u8 *Rx, int Rx_len, int Send_skip ){
- /* Execute this command string, including
+ /* Execute this command string, including
giving reset and setting to idle after command
- if Rx_len is set, we read out data from EEPROM */
+ if Rx_len is set, we read out data from EEPROM */
int i;
E_DEBUG("Command, Tx_len %d, Rx_len %d\n", Tx_len, Rx_len );
-
+
if(do_cpu_reset()){
/* Failed! */
return(-EIO);
}
if(Send_skip)
- /* Always send SKIP_ROM first to tell chip we are sending a command,
+ /* Always send SKIP_ROM first to tell chip we are sending a command,
except when we read out rom data for chip */
write_cpu_byte(SKIP_ROM);
-
+
/* Always have Tx data */
for(i=0;i<Tx_len;i++){
write_cpu_byte(Tx[i]);
}
-
+
if(Rx_len){
for(i=0;i<Rx_len;i++){
Rx[i]=read_cpu_byte();
}
}
-
+
set_idle();
E_DEBUG("Command done\n");
return(0);
-}
+}
int ee_init_cpu_data(void){
int i;
@@ -323,7 +323,7 @@
/* Leave it floting since altera is driving the same pin */
set_idle();
- /* Copy all User EEPROM data to scratchpad */
+ /* Copy all User EEPROM data to scratchpad */
for(i=0;i<USER_PAGES;i++){
Tx[0]=RECALL_MEMORY;
Tx[1]=EE_USER_PAGE_0+i;
@@ -332,16 +332,16 @@
/* Make sure chip doesnt store measurements in NVRAM */
Tx[0]=WRITE_SCRATCHPAD;
- Tx[1]=0; /* Page */
+ Tx[1]=0; /* Page */
Tx[2]=9;
if(ee_do_cpu_command(Tx,3,NULL,0,TRUE)) return(-EIO);
Tx[0]=COPY_SCRATCHPAD;
if(ee_do_cpu_command(Tx,2,NULL,0,TRUE)) return(-EIO);
-
+
for(i=0;i<10;i++){
udelay(1000);
}
-
+
return(0);
}
diff --git a/board/gth2/ee_access.h b/board/gth2/ee_access.h
index c21730e..926199d 100644
--- a/board/gth2/ee_access.h
+++ b/board/gth2/ee_access.h
@@ -21,7 +21,7 @@
#define EE_BUSY 0x40000000
#define EE_ERROR 0x20000000
-/* Commands */
+/* Commands */
#define EE_CMD_NOP 0
#define EE_CMD_INIT_RES 1
#define EE_CMD_WR_BYTE 2
diff --git a/board/gth2/ee_dev.h b/board/gth2/ee_dev.h
index acc3418..89ef2f8 100644
--- a/board/gth2/ee_dev.h
+++ b/board/gth2/ee_dev.h
@@ -21,7 +21,7 @@
#ifndef INCeedevh
#define INCeedevh
-#define E_DEBUG(fmt,args...) if( Debug ) printk(KERN_DEBUG"EE: " fmt, ##args)
+#define E_DEBUG(fmt,args...) if( Debug ) printk(KERN_DEBUG"EE: " fmt, ##args)
/* MIPS */
#define WRITE_PORT(Value) write_gpio_data(Value)
diff --git a/board/gth2/gth2.c b/board/gth2/gth2.c
index 77fc5b4..ffeaf58 100644
--- a/board/gth2/gth2.c
+++ b/board/gth2/gth2.c
@@ -61,13 +61,13 @@
u32 *serial_log_offsetp = (u32*)SERIAL_LOG_BUFFER;
/* Copy buffer from last run */
- memcpy(serial_log_buffer + 4096,
- serial_log_buffer,
+ memcpy(serial_log_buffer + 4096,
+ serial_log_buffer,
4096);
memset(serial_log_buffer, 0, 4096);
- *serial_log_offsetp = 4;
+ *serial_log_offsetp = 4;
}
@@ -118,7 +118,7 @@
udelay(1);
*sys_outputclr = GPIO_LEDCLK;
udelay(1);
-
+
value<<=1;
}
/* Data is enable output */
@@ -228,7 +228,7 @@
printf ("Invalid boot count %u, setting 1\n", Count);
Count = 1;
}
-
+
printf ("Boot attempt %d\n", Count);
data = (System << 8) | Count;
@@ -241,9 +241,9 @@
}
static int random_system(void){
- /* EEPROM read failed. Just try to choose one
+ /* EEPROM read failed. Just try to choose one
system release and hope it works */
-
+
/* FIXME */
return(SYSTEM_BOOT);
}
@@ -320,8 +320,8 @@
data = *addr;
system = data >> 8;
count = data & 0xFF;
- if ((system != SYSTEM_BOOT) &
- (system != SYSTEM2_BOOT) &
+ if ((system != SYSTEM_BOOT) &
+ (system != SYSTEM2_BOOT) &
(system != FAILSAFE_BOOT)) {
printf ("*** Wrong system %d\n", system);
system = FAILSAFE_BOOT;
diff --git a/board/gth2/lowlevel_init.S b/board/gth2/lowlevel_init.S
index 62e3657..983ff70 100644
--- a/board/gth2/lowlevel_init.S
+++ b/board/gth2/lowlevel_init.S
@@ -197,11 +197,11 @@
/* RCE2 CP Altera */
li t0, MEM_STCFG2
- li t1, 0x00000280 /* BE, EW */
+ li t1, 0x00000280 /* BE, EW */
sw t1, 0(t0)
li t0, MEM_STTIME2
- li t1, 0x0303000c
+ li t1, 0x0303000c
sw t1, 0(t0)
li t0, MEM_STADDR2
@@ -210,11 +210,11 @@
/* RCE3 DP Altera */
li t0, MEM_STCFG3
- li t1, 0x00000280 /* BE, EW */
+ li t1, 0x00000280 /* BE, EW */
sw t1, 0(t0)
li t0, MEM_STTIME3
- li t1, 0x0303000c
+ li t1, 0x0303000c
sw t1, 0(t0)
li t0, MEM_STADDR3
@@ -428,14 +428,14 @@
li t0, 0x80000000
li t1, 0xFFF000 /* 64 MB */
mt1: lw t2, 0(t0)
- bne t0, t2, memhang
+ bne t0, t2, memhang
add t1, -1
add t0, 4
bne t1, zero, mt1
nop
nop
.globl clearmem
-clearmem:
+clearmem:
/* Clear memory */
li t0, 0x80000000
li t1, 0xFFF000 /* 64 MB */
@@ -445,10 +445,10 @@
bne t1, zero, mtc
nop
nop
-memtestend:
+memtestend:
j ra
nop
-
-memhang:
+
+memhang:
b memhang
nop
diff --git a/board/icu862/Makefile b/board/icu862/Makefile
index 7a2014d..7b2b545 100644
--- a/board/icu862/Makefile
+++ b/board/icu862/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o
+OBJS = $(BOARD).o flash.o pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/icu862/pcmcia.c b/board/icu862/pcmcia.c
new file mode 100644
index 0000000..20f653b
--- /dev/null
+++ b/board/icu862/pcmcia.c
@@ -0,0 +1,268 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "ICU862"
+
+static void cfg_port_B (void)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ uint reg;
+
+ immap = (immap_t *)CFG_IMMR;
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /*
+ * Configure Port B for TPS2205 PC-Card Power-Interface Switch
+ *
+ * Switch off all voltages, assert shutdown
+ */
+ reg = cp->cp_pbdat;
+ reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
+ TPS2205_VCC3 | TPS2205_VCC5 | /* VAVCC => Hi-Z */
+ TPS2205_SHDN); /* enable switch */
+ cp->cp_pbdat = reg;
+
+ cp->cp_pbpar &= ~(TPS2205_INPUTS | TPS2205_OUTPUTS);
+
+ reg = cp->cp_pbdir & ~(TPS2205_INPUTS);
+ cp->cp_pbdir = reg | TPS2205_OUTPUTS;
+
+ debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
+ cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ volatile sysconf8xx_t *sysp;
+ uint reg, pipr, mask;
+ int i;
+
+ debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ udelay(10000);
+
+ immap = (immap_t *)CFG_IMMR;
+ sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /* Configure Port B for TPS2205 PC-Card Power-Interface Switch */
+ cfg_port_B ();
+
+ /*
+ * Configure SIUMCR to enable PCMCIA port B
+ * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+ */
+ sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
+ pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Make sure there is a card in the slot, then configure the interface.
+ */
+ udelay(10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n",
+ __LINE__,__FUNCTION__,
+ &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+ if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ /*
+ * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+ */
+ mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+ pipr = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+ pipr,
+ (reg&PCMCIA_VS1(slot))?"n":"ff",
+ (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+ reg = cp->cp_pbdat;
+ if ((pipr & mask) == mask) {
+ reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
+ TPS2205_VCC3); /* 3V off */
+ reg &= ~(TPS2205_VCC5); /* 5V on */
+ puts (" 5.0V card found: ");
+ } else {
+ reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
+ TPS2205_VCC5); /* 5V off */
+ reg &= ~(TPS2205_VCC3); /* 3V on */
+ puts (" 3.3V card found: ");
+ }
+
+ debug ("\nPB DAT: %08x -> 3.3V %s 5.0V %s VPP_PGM %s VPP_VCC %s\n",
+ reg,
+ (reg & TPS2205_VCC3) ? "off" : "on",
+ (reg & TPS2205_VCC5) ? "off" : "on",
+ (reg & TPS2205_VPP_PGM) ? "off" : "on",
+ (reg & TPS2205_VPP_VCC) ? "off" : "on" );
+
+ cp->cp_pbdat = reg;
+
+ /* Wait 500 ms; use this to check for over-current */
+ for (i=0; i<5000; ++i) {
+ if ((cp->cp_pbdat & TPS2205_OC) == 0) {
+ printf (" *** Overcurrent - Safety shutdown ***\n");
+ cp->cp_pbdat &= ~(TPS2205_SHDN);
+ return (1);
+ }
+ udelay (100);
+ }
+
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ immap = (immap_t *)CFG_IMMR;
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+ /* Shut down */
+ cp->cp_pbdat &= ~(TPS2205_SHDN);
+
+ /* Configure PCMCIA General Control Register */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(10000);
+
+ return (0);
+}
+#endif /* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("voltage_set: "
+ PCMCIA_BOARD_MSG
+ " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+ 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+ immap = (immap_t *)CFG_IMMR;
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ /*
+ * Disable PCMCIA buffers (isolate the interface)
+ * and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Configure Port C pins for
+ * 5 Volts Enable and 3 Volts enable,
+ * Turn all power pins to Hi-Z
+ */
+ debug ("PCMCIA power OFF\n");
+ cfg_port_B (); /* Enables switch, but all in Hi-Z */
+
+ reg = cp->cp_pbdat;
+
+ switch(vcc) {
+ case 0: break; /* Switch off */
+ case 33: reg &= ~TPS2205_VCC3; break; /* Switch on 3.3V */
+ case 50: reg &= ~TPS2205_VCC5; break; /* Switch on 5.0V */
+ default: goto done;
+ }
+
+ /* Checking supported voltages */
+
+ debug ("PIPR: 0x%x --> %s\n",
+ pcmp->pcmc_pipr,
+ (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+ cp->cp_pbdat = reg;
+
+#ifdef DEBUG
+{
+ char *s;
+
+ if ((reg & TPS2205_VCC3) == 0) {
+ s = "at 3.3V";
+ } else if ((reg & TPS2205_VCC5) == 0) {
+ s = "at 5.0V";
+ } else {
+ s = "down";
+ }
+ printf ("PCMCIA powered %s\n", s);
+}
+#endif
+
+done:
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+ slot+'A');
+ return (0);
+}
+
+#endif /* CONFIG_PCMCIA */
diff --git a/board/kup/common/pcmcia.c b/board/kup/common/pcmcia.c
new file mode 100644
index 0000000..1f61a0e
--- /dev/null
+++ b/board/kup/common/pcmcia.c
@@ -0,0 +1,225 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "KUP"
+
+#define KUP4K_PCMCIA_B_3V3 (0x00020000)
+
+int pcmcia_hardware_enable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ volatile sysconf8xx_t *sysp;
+ uint reg, mask;
+
+ debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ udelay(10000);
+
+ immap = (immap_t *)CFG_IMMR;
+ sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /*
+ * Configure SIUMCR to enable PCMCIA port B
+ * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+ */
+ sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK(slot);
+ pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(slot) = reg;
+ udelay(2500);
+
+ /*
+ * Configure Port B pins for
+ * 3 Volts enable
+ */
+ if (slot) { /* Slot A is built-in */
+ cp->cp_pbdir |= KUP4K_PCMCIA_B_3V3;
+ cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
+ /* remove all power */
+ cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3; /* active low */
+ }
+ /*
+ * Make sure there is a card in the slot, then configure the interface.
+ */
+ udelay(10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n",
+ __LINE__,__FUNCTION__,
+ &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+ if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ /*
+ * Power On.
+ */
+ printf("%s Slot %c:", slot ? "" : "\n", 'A' + slot);
+ mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+ reg = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+ reg,
+ (reg&PCMCIA_VS1(slot))?"n":"ff",
+ (reg&PCMCIA_VS2(slot))?"n":"ff");
+ if ((reg & mask) == mask) {
+ puts (" 5.0V card found: NOT SUPPORTED !!!\n");
+ } else {
+ if(slot)
+ cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
+ puts (" 3.3V card found: ");
+ }
+#if 0
+ /* VCC switch error flag, PCMCIA slot INPACK_ pin */
+ cp->cp_pbdir &= ~(0x0020 | 0x0010);
+ cp->cp_pbpar &= ~(0x0020 | 0x0010);
+ udelay(500000);
+#endif
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(slot);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(slot) = reg;
+
+ udelay(250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /* remove all power */
+ if (slot)
+ cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3;
+
+ /* Configure PCMCIA General Control Register */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(slot) = reg;
+
+ udelay(10000);
+
+ return (0);
+}
+#endif /* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("voltage_set: " \
+ PCMCIA_BOARD_MSG \
+ " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+ 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+ if (!slot) /* Slot A is not configurable */
+ return 0;
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /*
+ * Disable PCMCIA buffers (isolate the interface)
+ * and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = PCMCIA_PGCRX(slot);
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(slot) = reg;
+ udelay(500);
+
+ debug ("PCMCIA power OFF\n");
+ /*
+ * Configure Port B pins for
+ * 3 Volts enable
+ */
+ cp->cp_pbdir |= KUP4K_PCMCIA_B_3V3;
+ cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
+ /* remove all power */
+ cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3; /* active low */
+
+ switch(vcc) {
+ case 0: break;
+ case 33:
+ cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
+ debug ("PCMCIA powered at 3.3V\n");
+ break;
+ case 50:
+ debug ("PCMCIA: 5Volt vcc not supported\n");
+ break;
+ default:
+ puts("PCMCIA: vcc not supported");
+ break;
+ }
+ udelay(10000);
+ /* Checking supported voltages */
+
+ debug ("PIPR: 0x%x --> %s\n",
+ pcmp->pcmc_pipr,
+ (pcmp->pcmc_pipr & (0x80000000 >> (slot << 4)))
+ ? "only 5 V --> NOT SUPPORTED"
+ : "can do 3.3V");
+
+
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(slot);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(slot) = reg;
+ udelay(500);
+
+ debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+ slot+'A');
+ return (0);
+}
+
+#endif /* CONFIG_PCMCIA */
diff --git a/board/kup/kup4k/Makefile b/board/kup/kup4k/Makefile
index 62d289b..4a3954c 100644
--- a/board/kup/kup4k/Makefile
+++ b/board/kup/kup4k/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o
+OBJS = $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/kup/kup4x/Makefile b/board/kup/kup4x/Makefile
index 62d289b..4a3954c 100644
--- a/board/kup/kup4x/Makefile
+++ b/board/kup/kup4x/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o
+OBJS = $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/lwmon/Makefile b/board/lwmon/Makefile
index 7a2014d..7b2b545 100644
--- a/board/lwmon/Makefile
+++ b/board/lwmon/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o
+OBJS = $(BOARD).o flash.o pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/lwmon/pcmcia.c b/board/lwmon/pcmcia.c
new file mode 100644
index 0000000..2349286
--- /dev/null
+++ b/board/lwmon/pcmcia.c
@@ -0,0 +1,240 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+#include <i2c.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "LWMON"
+
+/* #define's for MAX1604 Power Switch */
+#define MAX1604_OP_SUS 0x80
+#define MAX1604_VCCBON 0x40
+#define MAX1604_VCC_35 0x20
+#define MAX1604_VCCBHIZ 0x10
+#define MAX1604_VPPBON 0x08
+#define MAX1604_VPPBPBPGM 0x04
+#define MAX1604_VPPBHIZ 0x02
+/* reserved 0x01 */
+
+int pcmcia_hardware_enable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ volatile sysconf8xx_t *sysp;
+ uint reg, mask;
+ uchar val;
+
+
+ debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ /* Switch on PCMCIA port in PIC register 0x60 */
+ reg = pic_read (0x60);
+ debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+ reg &= ~0x10;
+ /* reg |= 0x08; Vpp not needed */
+ pic_write (0x60, reg);
+#ifdef DEBUG
+ reg = pic_read (0x60);
+ printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+#endif
+ udelay(10000);
+
+ immap = (immap_t *)CFG_IMMR;
+ sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /*
+ * Configure SIUMCR to enable PCMCIA port B
+ * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+ */
+ sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
+ pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Make sure there is a card in the slot, then configure the interface.
+ */
+ udelay(10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n",
+ __LINE__,__FUNCTION__,
+ &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+ if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ /*
+ * Power On.
+ */
+ mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+ reg = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+ reg,
+ (reg&PCMCIA_VS1(slot))?"n":"ff",
+ (reg&PCMCIA_VS2(slot))?"n":"ff");
+ if ((reg & mask) == mask) {
+ val = 0; /* VCCB3/5 = 0 ==> use Vx = 5.0 V */
+ puts (" 5.0V card found: ");
+ } else {
+ val = MAX1604_VCC_35; /* VCCB3/5 = 1 ==> use Vy = 3.3 V */
+ puts (" 3.3V card found: ");
+ }
+
+ /* switch VCC on */
+ val |= MAX1604_OP_SUS | MAX1604_VCCBON;
+ i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+
+ udelay(500000);
+
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ volatile immap_t *immap;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+ uchar val;
+
+ debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+ /* remove all power, put output in high impedance state */
+ val = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
+ i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+
+ /* Configure PCMCIA General Control Register */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ /* Switch off PCMCIA port in PIC register 0x60 */
+ reg = pic_read (0x60);
+ debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+ reg |= 0x10;
+ reg &= ~0x08;
+ pic_write (0x60, reg);
+#ifdef DEBUG
+ reg = pic_read (0x60);
+ printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+#endif
+ udelay(10000);
+
+ return (0);
+}
+#endif /* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+ volatile immap_t *immap;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+ uchar val;
+
+ debug ("voltage_set: "
+ PCMCIA_BOARD_MSG
+ " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+ 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ /*
+ * Disable PCMCIA buffers (isolate the interface)
+ * and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Turn off all power (switch to high impedance)
+ */
+ debug ("PCMCIA power OFF\n");
+ val = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
+ i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+
+ val = 0;
+ switch(vcc) {
+ case 0: break;
+ case 33: val = MAX1604_VCC_35; break;
+ case 50: break;
+ default: goto done;
+ }
+
+ /* Checking supported voltages */
+
+ debug ("PIPR: 0x%x --> %s\n",
+ pcmp->pcmc_pipr,
+ (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+ i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+ if (val) {
+ debug ("PCMCIA powered at %sV\n",
+ (val & MAX1604_VCC_35) ? "3.3" : "5.0");
+ } else {
+ debug ("PCMCIA powered down\n");
+ }
+
+done:
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+ slot+'A');
+ return (0);
+}
+
+#endif /* CONFIG_PCMCIA */
diff --git a/board/mbx8xx/Makefile b/board/mbx8xx/Makefile
index 3e8376c..e4d1099 100644
--- a/board/mbx8xx/Makefile
+++ b/board/mbx8xx/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o vpd.o
+OBJS = $(BOARD).o flash.o vpd.o pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/mbx8xx/pcmcia.c b/board/mbx8xx/pcmcia.c
new file mode 100644
index 0000000..132a688
--- /dev/null
+++ b/board/mbx8xx/pcmcia.c
@@ -0,0 +1,166 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#include "csr.h"
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+/* A lot of this has been taken from the RPX code in this file it works from me.
+ I have added the voltage selection for the MBX board. */
+
+/* MBX voltage bit in control register #2 */
+#define CR2_VPP12 ((uchar)0x10)
+#define CR2_VPPVDD ((uchar)0x20)
+#define CR2_VDD5 ((uchar)0x40)
+#define CR2_VDD3 ((uchar)0x80)
+
+#define PCMCIA_BOARD_MSG "MBX860"
+
+int pcmcia_voltage_set (int slot, int vcc, int vpp)
+{
+ uchar reg = 0;
+
+ debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+ 'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
+
+ switch (vcc) {
+ case 0:
+ break;
+ case 33:
+ reg |= CR2_VDD3;
+ break;
+ case 50:
+ reg |= CR2_VDD5;
+ break;
+ default:
+ return 1;
+ }
+
+ switch (vpp) {
+ case 0:
+ break;
+ case 33:
+ case 50:
+ if (vcc == vpp) {
+ reg |= CR2_VPPVDD;
+ } else {
+ return 1;
+ }
+ break;
+ case 120:
+ reg |= CR2_VPP12;
+ break;
+ default:
+ return 1;
+ }
+
+ /* first, turn off all power */
+ MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
+
+ /* enable new powersettings */
+ MBX_CSR2 |= reg;
+ debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
+
+ return (0);
+}
+
+int pcmcia_hardware_enable (int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ volatile sysconf8xx_t *sysp;
+ uint reg, mask;
+
+ debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
+ 'A' + slot);
+
+ udelay (10000);
+
+ immap = (immap_t *) CFG_IMMR;
+ sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
+ pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
+ pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX (_slot_) = reg;
+ udelay (500);
+
+ /* remove all power */
+ pcmcia_voltage_set (slot, 0, 0);
+ /*
+ * Make sure there is a card in the slot, then configure the interface.
+ */
+ udelay(10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n",
+ __LINE__,__FUNCTION__,
+ &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+#ifndef CONFIG_HMI10
+ if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+#else
+ if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
+#endif /* CONFIG_HMI10 */
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ /*
+ * Power On.
+ */
+ mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
+ reg = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
+ (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
+ (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
+
+ if ((reg & mask) == mask) {
+ pcmcia_voltage_set (_slot_, 50, 0);
+ printf (" 5.0V card found: ");
+ } else {
+ pcmcia_voltage_set (_slot_, 33, 0);
+ printf (" 3.3V card found: ");
+ }
+
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX (_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX (_slot_) = reg;
+
+ udelay (250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return (0);
+ }
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable (int slot)
+{
+ return 0; /* No hardware to disable */
+}
+#endif /* CFG_CMD_PCMCIA */
+
+#endif /* CONFIG_PCMCIA */
diff --git a/board/mcc200/config.mk b/board/mcc200/config.mk
index fa55673..a822559 100644
--- a/board/mcc200/config.mk
+++ b/board/mcc200/config.mk
@@ -26,16 +26,18 @@
#
# Valid values for TEXT_BASE are:
#
-# 0xFFF00000 boot high (standard configuration)
-# 0xFE000000 boot low
+# 0xFC000000 boot low (standard configuration)
+# 0xFFF00000 boot high
# 0x00100000 boot from RAM (for testing only)
#
sinclude $(TOPDIR)/board/$(BOARDDIR)/config.tmp
ifndef TEXT_BASE
-## Standard: boot high
-TEXT_BASE = 0xFFF00000
+## Standard: boot low
+TEXT_BASE = 0xFC000000
+## Boot high
+# TEXT_BASE = 0xFFF00000
## For testing: boot from RAM
# TEXT_BASE = 0x00100000
endif
diff --git a/board/mcc200/mcc200.c b/board/mcc200/mcc200.c
index b9b9a71..775030c 100644
--- a/board/mcc200/mcc200.c
+++ b/board/mcc200/mcc200.c
@@ -32,7 +32,12 @@
/* #include "mt48lc8m32b2-6-7.h" */
/* One MT48LC16M32S2 for 64 MB */
-#include "mt48lc16m32s2-75.h"
+/* #include "mt48lc16m32s2-75.h" */
+#if defined (CONFIG_MCC200_SDRAM)
+#include "mt48lc16m16a2-75.h"
+#else
+#include "mt46v16m16-75.h"
+#endif
DECLARE_GLOBAL_DATA_PTR;
@@ -198,6 +203,8 @@
int misc_init_r (void)
{
+ ulong flash_sup_end, snum;
+
/*
* Adjust flash start and offset to detected values
*/
@@ -249,9 +256,15 @@
*(volatile int*)MPC5XXX_CS0_CFG |= (1 << 6);
flash_protect (FLAG_PROTECT_CLEAR,
flash_info[0].start[0] + flash_info[0].size / 2,
- (flash_info[0].start[0] + flash_info[0].size) / 2 - 1,
+ (flash_info[0].start[0] - 1) + flash_info[0].size,
&flash_info[0]);
*(volatile int*)MPC5XXX_CS0_CFG &= ~(1 << 6);
+ printf ("Warning: Only 32 of 64 MB of Flash are accessible from U-Boot\n");
+ flash_info[0].size = 32 << 20;
+ for (snum = 0, flash_sup_end = gd->bd->bi_flashstart + (32<<20);
+ flash_info[0].start[snum] < flash_sup_end;
+ snum++);
+ flash_info[0].sector_count = snum;
}
return (0);
diff --git a/board/netstar/crcek.S b/board/netstar/crcek.S
index 6ca4d11..a74abf9 100644
--- a/board/netstar/crcek.S
+++ b/board/netstar/crcek.S
@@ -13,6 +13,7 @@
* u32 - crc32
*/
+#include <config.h>
#include "crcek.h"
/**
@@ -39,7 +40,7 @@
.macro crcuj, offset, size
mov r0, #0
ldr r1, \offset
- ldr r2, [r1]
+ ldr r2, [r1], #4
cmp r2, r0 @ no data, no problem
beq 2f
tst r2, #3 @ unaligned size
@@ -47,7 +48,6 @@
ldr r3, \size
cmp r2, r3 @ bogus size
bhi 2f
- add r1, r1, #4
do_crc32
ldr r1, [r1]
2:
@@ -55,16 +55,71 @@
.endm
.macro wait, reg
- mov \reg, #0x1000
+ mov \reg, #0x100000
3:
subs \reg, \reg, #0x1
bne 3b
-
.endm
+
.text
.globl crcek
crcek:
- b crc2_bad
+ /* Enable I-cache */
+ mrc p15, 0, r1, c0, c0, 0 @ read C15 ID register
+ mrc p15, 0, r1, c0, c0, 1 @ read C15 Cache information register
+ mrc p15, 0, r1, c1, c0, 0 @ read C15 Control register
+ orr r1, r1, #0x1000 @ enable I-cache, map interrupt vector 0xffff0000
+ mcr p15, 0, r1, c1, c0, 0 @ write C15 Control register
+ mov r1, #0x00
+ mcr p15, 0, r1, c7, c5, 0 @ Flush I-cache
+ nop
+ nop
+ nop
+ nop
+
+ /* Setup clocking mode */
+ ldr r0, MPU_CLKM_BASE @ base of CLOCK unit
+ ldrh r1, [r0, #0x18] @ ARM_SYST - get reset status
+ bic r1, r1, #(7 << 11) @ clear clock select
+ orr r1, r1, #(2 << 11) @ set synchronous scalable
+ mov r2, #0
+loop:
+ cmp r2, #1 @ this loop will wait for at least 100 cycles
+ streqh r1, [r0, #0x18] @ before issuing next request from MPU
+ add r2, r2, #1 @ on the 1st run code is loaded into I-cache
+ cmp r2, #16 @ and second run will set clocking mode
+ bne loop
+ nop
+
+ /* Setup clock dividers */
+ ldr r1, CKCTL_VAL
+ orr r1, r1, #0x2000 @ enable DSP clock
+ strh r1, [r0] @ setup clock divisors
+
+ /* Setup DPLL to generate requested freq */
+ ldr r0, DPLL1_BASE @ base of DPLL1 register
+ mov r1, #0x0010 @ set PLL_ENABLE
+ orr r1, r1, #0x2000 @ set IOB to new locking
+ orr r1, r1, #(OMAP5910_DPLL_MUL << 7) @ setup multiplier CLKREF
+ orr r1, r1, #(OMAP5910_DPLL_DIV << 5) @ setup divider CLKREF
+ strh r1, [r0] @ write
+
+locking:
+ ldrh r1, [r0] @ get DPLL value
+ tst r1, #0x01
+ beq locking @ while LOCK not set
+
+ /* Enable clock */
+ ldr r0, MPU_CLKM_BASE @ base of CLOCK unit
+ mov r1, #(1 << 10) @ disable idle mode do not check
+ @ nWAKEUP pin, other remain active
+ strh r1, [r0, #0x04]
+ ldr r1, EN_CLK_VAL
+ strh r1, [r0, #0x08]
+ mov r1, #0x003f @ FLASH.RP not enabled in idle and
+ strh r1, [r0, #0x0c] @ max delayed ( 32 x CLKIN )
+
+
mov r6, #0
crcuj _LOADER1_OFFSET, _LOADER_SIZE
bne crc1_bad
@@ -76,9 +131,8 @@
crc2_bad:
ldr r3, _LOADER1_OFFSET
ldr r4, _LOADER2_OFFSET
- b boot_2nd
- tst r6, #3
- beq one_is_bad @ one of them (or both) has bad crc
+ teq r6, #3
+ bne one_is_bad @ one of them (or both) has bad crc
ldr r1, [r3, #4]
ldr r2, [r4, #4]
cmp r1, r2 @ boot 2nd loader if versions differ
@@ -90,6 +144,7 @@
tst r6, #2
bne boot_2nd
@ We are doomed, so let user know.
+hell:
ldr r0, GPIO_BASE @ configure GPIO pins
ldr r1, GPIO_DIRECTION
strh r1, [r0, #0x08]
@@ -171,6 +226,15 @@
GPIO_BASE:
.word 0xfffce000
+MPU_CLKM_BASE:
+ .word 0xfffece00
+DPLL1_BASE:
+ .word 0xfffecf00
+
+CKCTL_VAL:
+ .word OMAP5910_ARM_CKCTL
+EN_CLK_VAL:
+ .word OMAP5910_ARM_EN_CLK
GPIO_DIRECTION:
.word 0x0000ffe7
diff --git a/board/netstar/crcit b/board/netstar/crcit
index 98ae42e..203645d 100755
--- a/board/netstar/crcit
+++ b/board/netstar/crcit
Binary files differ
diff --git a/board/netstar/crcit.c b/board/netstar/crcit.c
index f6d3066..ce98e20 100644
--- a/board/netstar/crcit.c
+++ b/board/netstar/crcit.c
@@ -77,7 +77,7 @@
} else if ((argc == 4) && (strcmp(argv[1], "-v") == 0)) {
char *endptr, *nptr = argv[2];
unsigned ver = strtoul(nptr, &endptr, 0);
- if (nptr != '\0' && endptr == '\0')
+ if (*nptr != '\0' && *endptr == '\0')
return doit(argv[3], ver);
}
fprintf(stderr, "Usage: crcit [-v version] <image>\n");
diff --git a/board/netstar/netstar.c b/board/netstar/netstar.c
index 4b7eba1..d6b620c 100644
--- a/board/netstar/netstar.c
+++ b/board/netstar/netstar.c
@@ -27,7 +27,6 @@
int board_init(void)
{
/* arch number of NetStar board */
- /* TODO: use define from asm/mach-types.h */
gd->bd->bi_arch_number = 692;
/* adress of boot parameters */
@@ -51,15 +50,11 @@
return 0;
}
-extern void partition_flash(void);
-
int misc_init_r(void)
{
return 0;
}
-extern void nand_init(void);
-
int board_late_init(void)
{
return 0;
diff --git a/board/netstar/setup.S b/board/netstar/setup.S
index f67786d..5dacc9c 100644
--- a/board/netstar/setup.S
+++ b/board/netstar/setup.S
@@ -145,25 +145,23 @@
nop
/* Setup clocking mode */
- ldr r0, OMAP5910_MPU_CLKM_BASE @ prepare base of CLOCK unit
- ldrh r1, [r0, #0x18] @ get reset status
+ ldr r0, OMAP5910_MPU_CLKM_BASE @ base of CLOCK unit
+ ldrh r1, [r0, #0x18] @ ARM_SYST - get reset status
bic r1, r1, #(7 << 11) @ clear clock select
orr r1, r1, #(2 << 11) @ set synchronous scalable
- mov r2, #0 @ set wait counter to 100 clock cycles
-
-icache_loop:
- cmp r2, #0x01
- streqh r1, [r0, #0x18]
- add r2, r2, #0x01
- cmp r2, #0x10
- bne icache_loop
+ mov r2, #0
+loop:
+ cmp r2, #1 @ this loop will wait for at least 100 cycles
+ streqh r1, [r0, #0x18] @ before issuing next request from MPU
+ add r2, r2, #1 @ on the 1st run code is loaded into I-cache
+ cmp r2, #16 @ and second run will set clocking mode
+ bne loop
nop
- /* Setup clock divisors */
- ldr r0, OMAP5910_MPU_CLKM_BASE @ base of CLOCK unit
+ /* Setup clock dividers */
ldr r1, _OMAP5910_ARM_CKCTL
orr r1, r1, #0x2000 @ enable DSP clock
- strh r1, [r0, #0x00] @ setup clock divisors
+ strh r1, [r0] @ setup clock divisors
/* Setup DPLL to generate requested freq */
ldr r0, OMAP5910_DPLL1_BASE @ base of DPLL1 register
@@ -186,8 +184,7 @@
ldr r1, _OMAP5910_ARM_EN_CLK
strh r1, [r0, #0x08]
mov r1, #0x003f @ FLASH.RP not enabled in idle and
- @ max delayed ( 32 x CLKIN )
- strh r1, [r0, #0x0c]
+ strh r1, [r0, #0x0c] @ max delayed ( 32 x CLKIN )
/* Configure 5910 pins functions to match our board. */
ldr r0, MUX_CONFIG_BASE
diff --git a/board/netta/Makefile b/board/netta/Makefile
index 68e2402..ee200c2 100644
--- a/board/netta/Makefile
+++ b/board/netta/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o dsp.o codec.o
+OBJS = $(BOARD).o flash.o dsp.o codec.o pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/netta/pcmcia.c b/board/netta/pcmcia.c
new file mode 100644
index 0000000..a3709f7
--- /dev/null
+++ b/board/netta/pcmcia.c
@@ -0,0 +1,370 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+/* some sane bit macros */
+#define _BD(_b) (1U << (31-(_b)))
+#define _BDR(_l, _h) (((((1U << (31-(_l))) - 1) << 1) | 1) & ~((1U << (31-(_h))) - 1))
+
+#define _BW(_b) (1U << (15-(_b)))
+#define _BWR(_l, _h) (((((1U << (15-(_l))) - 1) << 1) | 1) & ~((1U << (15-(_h))) - 1))
+
+#define _BB(_b) (1U << (7-(_b)))
+#define _BBR(_l, _h) (((((1U << (7-(_l))) - 1) << 1) | 1) & ~((1U << (7-(_h))) - 1))
+
+#define _B(_b) _BD(_b)
+#define _BR(_l, _h) _BDR(_l, _h)
+
+#define PCMCIA_BOARD_MSG "NETTA"
+
+static const unsigned short vppd_masks[2] = { _BW(14), _BW(15) };
+
+static void cfg_vppd(int no)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ unsigned short mask;
+
+ if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
+ return;
+
+ mask = vppd_masks[no];
+
+ immap->im_ioport.iop_papar &= ~mask;
+ immap->im_ioport.iop_paodr &= ~mask;
+ immap->im_ioport.iop_padir |= mask;
+}
+
+static void set_vppd(int no, int what)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ unsigned short mask;
+
+ if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
+ return;
+
+ mask = vppd_masks[no];
+
+ if (what)
+ immap->im_ioport.iop_padat |= mask;
+ else
+ immap->im_ioport.iop_padat &= ~mask;
+}
+
+static const unsigned short vccd_masks[2] = { _BW(10), _BW(6) };
+
+static void cfg_vccd(int no)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ unsigned short mask;
+
+ if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
+ return;
+
+ mask = vccd_masks[no];
+
+ immap->im_ioport.iop_papar &= ~mask;
+ immap->im_ioport.iop_paodr &= ~mask;
+ immap->im_ioport.iop_padir |= mask;
+}
+
+static void set_vccd(int no, int what)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ unsigned short mask;
+
+ if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
+ return;
+
+ mask = vccd_masks[no];
+
+ if (what)
+ immap->im_ioport.iop_padat |= mask;
+ else
+ immap->im_ioport.iop_padat &= ~mask;
+}
+
+static const unsigned short oc_mask = _BW(8);
+
+static void cfg_oc(void)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ unsigned short mask = oc_mask;
+
+ immap->im_ioport.iop_pcdir &= ~mask;
+ immap->im_ioport.iop_pcso &= ~mask;
+ immap->im_ioport.iop_pcint &= ~mask;
+ immap->im_ioport.iop_pcpar &= ~mask;
+}
+
+static int get_oc(void)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ unsigned short mask = oc_mask;
+ int what;
+
+ what = !!(immap->im_ioport.iop_pcdat & mask);;
+ return what;
+}
+
+static const unsigned short shdn_mask = _BW(12);
+
+static void cfg_shdn(void)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ unsigned short mask;
+
+ mask = shdn_mask;
+
+ immap->im_ioport.iop_papar &= ~mask;
+ immap->im_ioport.iop_paodr &= ~mask;
+ immap->im_ioport.iop_padir |= mask;
+}
+
+static void set_shdn(int what)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ unsigned short mask;
+
+ mask = shdn_mask;
+
+ if (what)
+ immap->im_ioport.iop_padat |= mask;
+ else
+ immap->im_ioport.iop_padat &= ~mask;
+}
+
+static void cfg_ports (void)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+
+ immap = (immap_t *)CFG_IMMR;
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+
+ cfg_vppd(0); cfg_vppd(1); /* VPPD0,VPPD1 VAVPP => Hi-Z */
+ cfg_vccd(0); cfg_vccd(1); /* 3V and 5V off */
+ cfg_shdn();
+ cfg_oc();
+
+ /*
+ * Configure Port A for TPS2211 PC-Card Power-Interface Switch
+ *
+ * Switch off all voltages, assert shutdown
+ */
+ set_vppd(0, 1); set_vppd(1, 1);
+ set_vccd(0, 0); set_vccd(1, 0);
+ set_shdn(1);
+
+ udelay(100000);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ volatile sysconf8xx_t *sysp;
+ uint reg, pipr, mask;
+ int i;
+
+ debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ udelay(10000);
+
+ immap = (immap_t *)CFG_IMMR;
+ sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+ cfg_ports ();
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
+ pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(500);
+
+ /*
+ * Make sure there is a card in the slot, then configure the interface.
+ */
+ udelay(10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n",
+ __LINE__,__FUNCTION__,
+ &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+ if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ /*
+ * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+ */
+ mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+ pipr = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+ pipr,
+ (reg&PCMCIA_VS1(slot))?"n":"ff",
+ (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+ if ((pipr & mask) == mask) {
+ set_vppd(0, 1); set_vppd(1, 1); /* VAVPP => Hi-Z */
+ set_vccd(0, 0); set_vccd(1, 1); /* 5V on, 3V off */
+ puts (" 5.0V card found: ");
+ } else {
+ set_vppd(0, 1); set_vppd(1, 1); /* VAVPP => Hi-Z */
+ set_vccd(0, 1); set_vccd(1, 0); /* 5V off, 3V on */
+ puts (" 3.3V card found: ");
+ }
+
+ /* Wait 500 ms; use this to check for over-current */
+ for (i=0; i<5000; ++i) {
+ if (!get_oc()) {
+ printf (" *** Overcurrent - Safety shutdown ***\n");
+ set_vccd(0, 0); set_vccd(1, 0); /* VAVPP => Hi-Z */
+ return (1);
+ }
+ udelay (100);
+ }
+
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ volatile immap_t *immap;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+ /* Configure PCMCIA General Control Register */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ /* All voltages off / Hi-Z */
+ set_vppd(0, 1); set_vppd(1, 1);
+ set_vccd(0, 1); set_vccd(1, 1);
+
+ udelay(10000);
+
+ return (0);
+}
+#endif /* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+ ushort sreg;
+
+ debug ("voltage_set: "
+ PCMCIA_BOARD_MSG
+ " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+ 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+ immap = (immap_t *)CFG_IMMR;
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ /*
+ * Disable PCMCIA buffers (isolate the interface)
+ * and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Configure Port C pins for
+ * 5 Volts Enable and 3 Volts enable,
+ * Turn all power pins to Hi-Z
+ */
+ debug ("PCMCIA power OFF\n");
+ cfg_ports (); /* Enables switch, but all in Hi-Z */
+
+ sreg = immap->im_ioport.iop_pcdat;
+ set_vppd(0, 1); set_vppd(1, 1);
+
+ switch(vcc) {
+ case 0:
+ break; /* Switch off */
+
+ case 33:
+ set_vccd(0, 1); set_vccd(1, 0);
+ break;
+
+ case 50:
+ set_vccd(0, 0); set_vccd(1, 1);
+ break;
+
+ default:
+ goto done;
+ }
+
+ /* Checking supported voltages */
+
+ debug ("PIPR: 0x%x --> %s\n",
+ pcmp->pcmc_pipr,
+ (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+done:
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+ slot+'A');
+ return (0);
+}
+
+#endif /* CONFIG_PCMCIA */
diff --git a/board/ppmc7xx/config.mk b/board/ppmc7xx/config.mk
index bcb6c81..b5b46dc 100644
--- a/board/ppmc7xx/config.mk
+++ b/board/ppmc7xx/config.mk
@@ -1,6 +1,6 @@
#
# (C) Copyright 2005
-# Richard Danter, Wind River Systems
+# Richard Danter, Wind River Systems
#
# (C) Copyright 2000
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -22,11 +22,6 @@
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
-#
-
-#
-#
-#
TEXT_BASE = 0xFFF00000
TEXT_END = 0xFFF40000
diff --git a/board/ppmc7xx/flash.c b/board/ppmc7xx/flash.c
index 1cbcadc..4be6f13 100644
--- a/board/ppmc7xx/flash.c
+++ b/board/ppmc7xx/flash.c
@@ -1,10 +1,10 @@
/*
* flash.c
* -------
- *
+ *
* Flash programming routines for the Wind River PPMC 74xx/7xx
* based on flash.c from the TQM8260 board.
- *
+ *
* By Richard Danter (richard.danter@windriver.com)
* Copyright (C) 2005 Wind River Systems
*/
@@ -27,13 +27,13 @@
{
unsigned long msr;
DWORD cmd_reset = 0x00F000F000F000F0LL;
-
+
if (flash_info[0].flash_id != FLASH_UNKNOWN) {
msr = get_msr ();
set_msr (msr | MSR_FP);
write_via_fpu ((DWORD*)flash_info[0].start[0], &cmd_reset );
-
+
set_msr (msr);
}
}
@@ -50,16 +50,16 @@
/* Enable FPU */
msr = get_msr ();
- set_msr (msr | MSR_FP);
-
+ set_msr (msr | MSR_FP);
+
/* Write auto-select command sequence */
write_via_fpu ((DWORD*)(baseaddr + (0x0555 << 3)), &cmd_select[0] );
write_via_fpu ((DWORD*)(baseaddr + (0x02AA << 3)), &cmd_select[1] );
write_via_fpu ((DWORD*)(baseaddr + (0x0555 << 3)), &cmd_select[2] );
-
+
/* Restore FPU */
set_msr (msr);
-
+
/* Read manufacturer ID */
flashtest = *(volatile DWORD*)baseaddr;
switch ((int)flashtest) {
@@ -70,7 +70,7 @@
info->flash_id = FLASH_MAN_FUJ;
break;
default:
- /* No, faulty or unknown flash */
+ /* No, faulty or unknown flash */
info->flash_id = FLASH_UNKNOWN;
info->sector_count = 0;
info->size = 0;
@@ -291,7 +291,7 @@
DWORD cmd_erase[6] = { 0x00AA00AA00AA00AALL, 0x0055005500550055LL,
0x0080008000800080LL, 0x00AA00AA00AA00AALL,
0x0055005500550055LL, 0x0030003000300030LL };
-
+
if ((s_first < 0) || (s_first > s_last)) {
if (info->flash_id == FLASH_UNKNOWN) {
printf ("- missing\n");
@@ -319,7 +319,7 @@
/* Enable FPU */
msr = get_msr();
set_msr ( msr | MSR_FP );
-
+
/* Disable interrupts which might cause a timeout here */
flag = disable_interrupts ();
@@ -344,7 +344,7 @@
/* Restore FPU */
set_msr (msr);
-
+
/* wait at least 80us - let's wait 1 ms */
udelay (1000);
@@ -373,7 +373,7 @@
DONE:
/* reset to read mode */
flash_reset ();
-
+
printf (" done\n");
return 0;
}
@@ -446,7 +446,7 @@
DWORD data;
DWORD cmd_write[3] = { 0x00AA00AA00AA00AALL, 0x0055005500550055LL,
0x00A000A000A000A0LL };
-
+
for (data = 0, i = 0; i < 8; i++)
data = (data << 8) + *pdata++;
@@ -454,11 +454,11 @@
if ((*(DWORD*)dest & data) != data) {
return (2);
}
-
+
/* Enable FPU */
msr = get_msr();
set_msr( msr | MSR_FP );
-
+
/* Disable interrupts which might cause a timeout here */
flag = disable_interrupts ();
@@ -473,7 +473,7 @@
/* Restore FPU */
set_msr(msr);
-
+
/* data polling for D7 */
start = get_timer (0);
while (*(volatile DWORD*)dest != data ) {
diff --git a/board/ppmc7xx/init.S b/board/ppmc7xx/init.S
index e4ed7a6..99a818a 100644
--- a/board/ppmc7xx/init.S
+++ b/board/ppmc7xx/init.S
@@ -21,314 +21,314 @@
ori r4,r4,0x0000
lis r5,0xFEE0
ori r5,r5,0x0000
- lis r3,0x8000 # ADDR_00
+ lis r3,0x8000 # ADDR_00
ori r3,r3,0x0000
stwbrx r3,0,r4
- li r3,0x1057 # VENDOR
+ li r3,0x1057 # VENDOR
li r8, 0x0
sthbrx r3,r8,r5
- lis r3,0x8000 # ADDR_02
+ lis r3,0x8000 # ADDR_02
ori r3,r3,0x0002
stwbrx r3,0,r4
- li r3,0x0004 # ID
+ li r3,0x0004 # ID
li r8, 0x2
sthbrx r3,r8,r5
- lis r3,0x8000 # ADDR_04
+ lis r3,0x8000 # ADDR_04
ori r3,r3,0x0004
stwbrx r3,0,r4
- li r3,0x0006 # PCICMD
+ li r3,0x0006 # PCICMD
li r8, 0x0
sthbrx r3,r8,r5
- lis r3,0x8000 # ADDR_06
+ lis r3,0x8000 # ADDR_06
ori r3,r3,0x0006
stwbrx r3,0,r4
- li r3,0x00A0 # PCISTAT
+ li r3,0x00A0 # PCISTAT
li r8, 0x2
sthbrx r3,r8,r5
- lis r3,0x8000 # ADDR_08
+ lis r3,0x8000 # ADDR_08
ori r3,r3,0x0008
stwbrx r3,0,r4
- li r3,0x10 # REVID
+ li r3,0x10 # REVID
stb r3,0x0(r5)
- lis r3,0x8000 # ADDR_09
+ lis r3,0x8000 # ADDR_09
ori r3,r3,0x0009
stwbrx r3,0,r4
- li r3,0x00 # PROGIR
+ li r3,0x00 # PROGIR
stb r3,0x1(r5)
- lis r3,0x8000 # ADDR_0A
+ lis r3,0x8000 # ADDR_0A
ori r3,r3,0x000A
stwbrx r3,0,r4
- li r3,0x00 # SUBCCODE
+ li r3,0x00 # SUBCCODE
stb r3,0x2(r5)
- lis r3,0x8000 # ADDR_0B
+ lis r3,0x8000 # ADDR_0B
ori r3,r3,0x000B
stwbrx r3,0,r4
- li r3,0x06 # PBCCR
+ li r3,0x06 # PBCCR
stb r3,0x3(r5)
- lis r3,0x8000 # ADDR_0C
+ lis r3,0x8000 # ADDR_0C
ori r3,r3,0x000C
stwbrx r3,0,r4
- li r3,0x08 # PCLSR
+ li r3,0x08 # PCLSR
stb r3,0x0(r5)
- lis r3,0x8000 # ADDR_0D
+ lis r3,0x8000 # ADDR_0D
ori r3,r3,0x000D
stwbrx r3,0,r4
- li r3,0x00 # PLTR
+ li r3,0x00 # PLTR
stb r3,0x1(r5)
- lis r3,0x8000 # ADDR_0E
+ lis r3,0x8000 # ADDR_0E
ori r3,r3,0x000E
stwbrx r3,0,r4
- li r3,0x00 # HEADTYPE
+ li r3,0x00 # HEADTYPE
stb r3,0x2(r5)
- lis r3,0x8000 # ADDR_0F
+ lis r3,0x8000 # ADDR_0F
ori r3,r3,0x000F
stwbrx r3,0,r4
- li r3,0x00 # BISTCTRL
+ li r3,0x00 # BISTCTRL
stb r3,0x3(r5)
- lis r3,0x8000 # ADDR_10
+ lis r3,0x8000 # ADDR_10
ori r3,r3,0x0010
stwbrx r3,0,r4
- lis r3,0x0000 # LMBAR
+ lis r3,0x0000 # LMBAR
ori r3,r3,0x0008
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_14
+ lis r3,0x8000 # ADDR_14
ori r3,r3,0x0014
stwbrx r3,0,r4
- lis r3,0xF000 # PCSRBAR
+ lis r3,0xF000 # PCSRBAR
ori r3,r3,0x0000
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_3C
+ lis r3,0x8000 # ADDR_3C
ori r3,r3,0x003C
stwbrx r3,0,r4
- li r3,0x00 # ILR
+ li r3,0x00 # ILR
stb r3,0x0(r5)
- lis r3,0x8000 # ADDR_3D
+ lis r3,0x8000 # ADDR_3D
ori r3,r3,0x003D
stwbrx r3,0,r4
- li r3,0x01 # INTPIN
+ li r3,0x01 # INTPIN
stb r3,0x1(r5)
- lis r3,0x8000 # ADDR_3E
+ lis r3,0x8000 # ADDR_3E
ori r3,r3,0x003E
stwbrx r3,0,r4
- li r3,0x00 # MIN_GNT
+ li r3,0x00 # MIN_GNT
stb r3,0x2(r5)
- lis r3,0x8000 # ADDR_3F
+ lis r3,0x8000 # ADDR_3F
ori r3,r3,0x003F
stwbrx r3,0,r4
- li r3,0x00 # MAX_LAT
+ li r3,0x00 # MAX_LAT
stb r3,0x3(r5)
- lis r3,0x8000 # ADDR_40
+ lis r3,0x8000 # ADDR_40
ori r3,r3,0x0040
stwbrx r3,0,r4
- li r3,0x00 # BUSNB
+ li r3,0x00 # BUSNB
stb r3,0x0(r5)
- lis r3,0x8000 # ADDR_41
+ lis r3,0x8000 # ADDR_41
ori r3,r3,0x0041
stwbrx r3,0,r4
- li r3,0x00 # SBUSNB
+ li r3,0x00 # SBUSNB
stb r3,0x1(r5)
- lis r3,0x8000 # ADDR_46
+ lis r3,0x8000 # ADDR_46
ori r3,r3,0x0046
stwbrx r3,0,r4
-# li r3,0xE080 # PCIARB
- li r3,-0x1F80 # PCIARB
+# li r3,0xE080 # PCIARB
+ li r3,-0x1F80 # PCIARB
li r8, 0x2
sthbrx r3,r8,r5
- lis r3,0x8000 # ADDR_70
+ lis r3,0x8000 # ADDR_70
ori r3,r3,0x0070
stwbrx r3,0,r4
- li r3,0x0000 # PMCR1
+ li r3,0x0000 # PMCR1
li r8, 0x0
sthbrx r3,r8,r5
- lis r3,0x8000 # ADDR_72
+ lis r3,0x8000 # ADDR_72
ori r3,r3,0x0072
stwbrx r3,0,r4
- li r3,0xC0 # PMCR2
+ li r3,0xC0 # PMCR2
stb r3,0x2(r5)
- lis r3,0x8000 # ADDR_73
+ lis r3,0x8000 # ADDR_73
ori r3,r3,0x0073
stwbrx r3,0,r4
- li r3,0xEF # ODCR
+ li r3,0xEF # ODCR
stb r3,0x3(r5)
- lis r3,0x8000 # ADDR_74
+ lis r3,0x8000 # ADDR_74
ori r3,r3,0x0074
stwbrx r3,0,r4
- li r3,0x7D00 # CLKDCR
+ li r3,0x7D00 # CLKDCR
li r8, 0x0
sthbrx r3,r8,r5
- lis r3,0x8000 # ADDR_76
+ lis r3,0x8000 # ADDR_76
ori r3,r3,0x0076
stwbrx r3,0,r4
- li r3,0x00 # MDCR
+ li r3,0x00 # MDCR
stb r3,0x2(r5)
lis r6,0xFCE0
ori r6,r6,0x0000 # r6 is the EUMBAR Base Address
- lis r3,0x8000 # ADDR_78
+ lis r3,0x8000 # ADDR_78
ori r3,r3,0x0078
stwbrx r3,0,r4
- lis r3,0xFCE0 # EUMBBAR
+ lis r3,0xFCE0 # EUMBBAR
ori r3,r3,0x0000
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_80
+ lis r3,0x8000 # ADDR_80
ori r3,r3,0x0080
stwbrx r3,0,r4
- lis r3,0xFFFF # MSADDR1
+ lis r3,0xFFFF # MSADDR1
ori r3,r3,0x4000
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_84
+ lis r3,0x8000 # ADDR_84
ori r3,r3,0x0084
stwbrx r3,0,r4
- lis r3,0xFFFF # MSADDR2
+ lis r3,0xFFFF # MSADDR2
ori r3,r3,0xFFFF
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_88
+ lis r3,0x8000 # ADDR_88
ori r3,r3,0x0088
stwbrx r3,0,r4
- lis r3,0x0303 # EMSADDR1
+ lis r3,0x0303 # EMSADDR1
ori r3,r3,0x0000
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_8C
+ lis r3,0x8000 # ADDR_8C
ori r3,r3,0x008C
stwbrx r3,0,r4
- lis r3,0x0303 # EMSADDR2
+ lis r3,0x0303 # EMSADDR2
ori r3,r3,0x0303
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_90
+ lis r3,0x8000 # ADDR_90
ori r3,r3,0x0090
stwbrx r3,0,r4
- lis r3,0xFFFF # EMEADDR1
+ lis r3,0xFFFF # EMEADDR1
ori r3,r3,0x7F3F
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_94
+ lis r3,0x8000 # ADDR_94
ori r3,r3,0x0094
stwbrx r3,0,r4
- lis r3,0xFFFF # EMEADDR2
+ lis r3,0xFFFF # EMEADDR2
ori r3,r3,0xFFFF
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_98
+ lis r3,0x8000 # ADDR_98
ori r3,r3,0x0098
stwbrx r3,0,r4
- lis r3,0x0303 # EXTEMEM1
+ lis r3,0x0303 # EXTEMEM1
ori r3,r3,0x0000
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_9C
+ lis r3,0x8000 # ADDR_9C
ori r3,r3,0x009C
stwbrx r3,0,r4
- lis r3,0x0303 # EXTEMEM2
+ lis r3,0x0303 # EXTEMEM2
ori r3,r3,0x0303
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_A0
+ lis r3,0x8000 # ADDR_A0
ori r3,r3,0x00A0
stwbrx r3,0,r4
- li r3,0x03 # MEMBNKEN
+ li r3,0x03 # MEMBNKEN
stb r3,0x0(r5)
- lis r3,0x8000 # ADDR_A3
+ lis r3,0x8000 # ADDR_A3
ori r3,r3,0x00A3
stwbrx r3,0,r4
- li r3,0x00 # MEMPMODE
+ li r3,0x00 # MEMPMODE
stb r3,0x3(r5)
- lis r3,0x8000 # ADDR_B8
+ lis r3,0x8000 # ADDR_B8
ori r3,r3,0x00B8
stwbrx r3,0,r4
- li r3,0x00 # ECCCNT
+ li r3,0x00 # ECCCNT
stb r3,0x0(r5)
- lis r3,0x8000 # ADDR_B9
+ lis r3,0x8000 # ADDR_B9
ori r3,r3,0x00B9
stwbrx r3,0,r4
- li r3,0x00 # ECCTRG
+ li r3,0x00 # ECCTRG
stb r3,0x1(r5)
- lis r3,0x8000 # ADDR_C0
+ lis r3,0x8000 # ADDR_C0
ori r3,r3,0x00C0
stwbrx r3,0,r4
- li r3,0xFF # ERRENR1
+ li r3,0xFF # ERRENR1
stb r3,0x0(r5)
- lis r3,0x8000 # ADDR_C1
+ lis r3,0x8000 # ADDR_C1
ori r3,r3,0x00C1
stwbrx r3,0,r4
- li r3,0x00 # ERRDR1
+ li r3,0x00 # ERRDR1
stb r3,0x1(r5)
- lis r3,0x8000 # ADDR_C3
+ lis r3,0x8000 # ADDR_C3
ori r3,r3,0x00C3
stwbrx r3,0,r4
- li r3,0x50 # IPBESR
+ li r3,0x50 # IPBESR
stb r3,0x3(r5)
- lis r3,0x8000 # ADDR_C4
+ lis r3,0x8000 # ADDR_C4
ori r3,r3,0x00C4
stwbrx r3,0,r4
- li r3,0xBF # ERRENR2
+ li r3,0xBF # ERRENR2
stb r3,0x0(r5)
- lis r3,0x8000 # ADDR_C5
+ lis r3,0x8000 # ADDR_C5
ori r3,r3,0x00C5
stwbrx r3,0,r4
- li r3,0x00 # ERRDR2
+ li r3,0x00 # ERRDR2
stb r3,0x1(r5)
- lis r3,0x8000 # ADDR_C7
+ lis r3,0x8000 # ADDR_C7
ori r3,r3,0x00C7
stwbrx r3,0,r4
- li r3,0x00 # PCIBESR
+ li r3,0x00 # PCIBESR
stb r3,0x3(r5)
- lis r3,0x8000 # ADDR_C8
+ lis r3,0x8000 # ADDR_C8
ori r3,r3,0x00C8
stwbrx r3,0,r4
- lis r3,0x0000 # BERRADDR
+ lis r3,0x0000 # BERRADDR
ori r3,r3,0xE0FE
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_E0
+ lis r3,0x8000 # ADDR_E0
ori r3,r3,0x00E0
stwbrx r3,0,r4
- li r3,0xC0 # AMBOR
+ li r3,0xC0 # AMBOR
stb r3,0x0(r5)
- lis r3,0x8000 # ADDR_F4
+ lis r3,0x8000 # ADDR_F4
ori r3,r3,0x00F4
stwbrx r3,0,r4
- lis r3,0x0000 # MCCR2
+ lis r3,0x0000 # MCCR2
ori r3,r3,0x020C
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_F8
+ lis r3,0x8000 # ADDR_F8
ori r3,r3,0x00F8
stwbrx r3,0,r4
- lis r3,0x0230 # MCCR3
+ lis r3,0x0230 # MCCR3
ori r3,r3,0x0000
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_FC
+ lis r3,0x8000 # ADDR_FC
ori r3,r3,0x00FC
stwbrx r3,0,r4
- lis r3,0x2532 # MCCR4
+ lis r3,0x2532 # MCCR4
ori r3,r3,0x2220
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_F0
+ lis r3,0x8000 # ADDR_F0
ori r3,r3,0x00F0
stwbrx r3,0,r4
- lis r3,0xFFC8 # MCCR1
+ lis r3,0xFFC8 # MCCR1
ori r3,r3,0x0000
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_A8
+ lis r3,0x8000 # ADDR_A8
ori r3,r3,0x00A8
stwbrx r3,0,r4
- lis r3,0xFF14 # PICR1
+ lis r3,0xFF14 # PICR1
ori r3,r3,0x1CC8
li r8, 0x0
stwbrx r3,r8,r5
- lis r3,0x8000 # ADDR_AC
+ lis r3,0x8000 # ADDR_AC
ori r3,r3,0x00AC
stwbrx r3,0,r4
- lis r3,0x0000 # PICR2
+ lis r3,0x0000 # PICR2
ori r3,r3,0x0000
li r8, 0x0
stwbrx r3,r8,r5
diff --git a/board/ppmc7xx/ppmc7xx.c b/board/ppmc7xx/ppmc7xx.c
index 0597c72..402ac5e 100644
--- a/board/ppmc7xx/ppmc7xx.c
+++ b/board/ppmc7xx/ppmc7xx.c
@@ -1,9 +1,9 @@
/*
* ppmc7xx.c
* ---------
- *
+ *
* Main board-specific routines for Wind River PPMC 7xx/74xx board.
- *
+ *
* By Richard Danter (richard.danter@windriver.com)
* Copyright (C) 2005 Wind River Systems
*/
@@ -24,7 +24,7 @@
/*
* initdram()
- *
+ *
* This function normally initialises the (S)DRAM of the system. For this board
* the SDRAM was already initialised by board_asm_init (see init.S) so we just
* return the size of RAM.
@@ -37,12 +37,12 @@
/*
* after_reloc()
- *
+ *
* This is called after U-Boot has been copied from Flash/ROM to RAM. It gives
* us an opportunity to do some additional setup before the rest of the system
* is initialised. We don't need to do anything, so we just call board_init_r()
* which should never return.
- */
+ */
void after_reloc( ulong dest_addr, gd_t* gd )
{
/* Jump to the main U-Boot board init code */
@@ -52,7 +52,7 @@
/*
* checkboard()
- *
+ *
* We could do some board level checks here, such as working out what version
* it is, but for this board we simply display it's name (on the console).
*/
@@ -65,7 +65,7 @@
/*
* misc_init_r
- *
+ *
* Used for other setup which needs to be done late in the bring-up phase.
*/
int misc_init_r( void )
@@ -78,27 +78,27 @@
/* Enable the I-Cache */
icache_enable();
-
+
return 0;
}
/*
* do_reset()
- *
+ *
* Shell command to reset the board.
*/
void do_reset( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[] )
{
printf( "Resetting...\n" );
-
+
/* Disabe and invalidate cache */
icache_disable();
dcache_disable();
/* Jump to warm start (in RAM) */
_start_warm();
-
+
/* Should never get here */
while(1);
}
diff --git a/board/r360mpi/Makefile b/board/r360mpi/Makefile
index 13ce9fc..1a7e7a6 100644
--- a/board/r360mpi/Makefile
+++ b/board/r360mpi/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o
+OBJS = $(BOARD).o flash.o pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/r360mpi/pcmcia.c b/board/r360mpi/pcmcia.c
new file mode 100644
index 0000000..7d34ac8
--- /dev/null
+++ b/board/r360mpi/pcmcia.c
@@ -0,0 +1,236 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "R360MPI"
+
+int pcmcia_hardware_enable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ volatile sysconf8xx_t *sysp;
+ uint reg, mask;
+
+ debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ udelay(10000);
+
+ immap = (immap_t *)CFG_IMMR;
+ sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /*
+ * Configure SIUMCR to enable PCMCIA port B
+ * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+ */
+ sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
+ pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Configure Ports A, B & C pins for
+ * 5 Volts Enable and 3 Volts enable
+ */
+ immap->im_ioport.iop_pcpar &= ~(0x0400);
+ immap->im_ioport.iop_pcso &= ~(0x0400);/*
+ immap->im_ioport.iop_pcdir |= 0x0400;*/
+
+ immap->im_ioport.iop_papar &= ~(0x0200);/*
+ immap->im_ioport.iop_padir |= 0x0200;*/
+#if 0
+ immap->im_ioport.iop_pbpar &= ~(0xC000);
+ immap->im_ioport.iop_pbdir &= ~(0xC000);
+#endif
+ /* remove all power */
+
+ immap->im_ioport.iop_pcdat |= 0x0400;
+ immap->im_ioport.iop_padat |= 0x0200;
+
+ /*
+ * Make sure there is a card in the slot, then configure the interface.
+ */
+ udelay(10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n",
+ __LINE__,__FUNCTION__,
+ &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+ if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ /*
+ * Power On.
+ */
+ mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+ reg = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+ reg,
+ (reg&PCMCIA_VS1(slot))?"n":"ff",
+ (reg&PCMCIA_VS2(slot))?"n":"ff");
+ if ((reg & mask) == mask) {
+ immap->im_ioport.iop_pcdat &= ~(0x4000);
+ puts (" 5.0V card found: ");
+ } else {
+ immap->im_ioport.iop_padat &= ~(0x0002);
+ puts (" 3.3V card found: ");
+ }
+ immap->im_ioport.iop_pcdir |= 0x0400;
+ immap->im_ioport.iop_padir |= 0x0200;
+#if 0
+ /* VCC switch error flag, PCMCIA slot INPACK_ pin */
+ cp->cp_pbdir &= ~(0x0020 | 0x0010);
+ cp->cp_pbpar &= ~(0x0020 | 0x0010);
+ udelay(500000);
+#endif
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ volatile immap_t *immap;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+ /* remove all power */
+ immap->im_ioport.iop_pcdat |= 0x0400;
+ immap->im_ioport.iop_padat |= 0x0200;
+
+ /* Configure PCMCIA General Control Register */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(10000);
+
+ return (0);
+}
+#endif /* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+ volatile immap_t *immap;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("voltage_set: "
+ PCMCIA_BOARD_MSG
+ " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+ 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ /*
+ * Disable PCMCIA buffers (isolate the interface)
+ * and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Configure Ports A & C pins for
+ * 5 Volts Enable and 3 Volts enable,
+ * Turn off all power
+ */
+ debug ("PCMCIA power OFF\n");
+ immap->im_ioport.iop_pcpar &= ~(0x0400);
+ immap->im_ioport.iop_pcso &= ~(0x0400);/*
+ immap->im_ioport.iop_pcdir |= 0x0400;*/
+
+ immap->im_ioport.iop_papar &= ~(0x0200);/*
+ immap->im_ioport.iop_padir |= 0x0200;*/
+
+ immap->im_ioport.iop_pcdat |= 0x0400;
+ immap->im_ioport.iop_padat |= 0x0200;
+
+ reg = 0;
+ switch(vcc) {
+ case 0: break;
+ case 33: reg |= 0x0200; break;
+ case 50: reg |= 0x0400; break;
+ default: goto done;
+ }
+
+ /* Checking supported voltages */
+
+ debug ("PIPR: 0x%x --> %s\n",
+ pcmp->pcmc_pipr,
+ (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+ if (reg & 0x0200)
+ immap->im_ioport.iop_pcdat &= !reg;
+ if (reg & 0x0400)
+ immap->im_ioport.iop_padat &= !reg;
+ immap->im_ioport.iop_pcdir |= 0x0200;
+ immap->im_ioport.iop_padir |= 0x0400;
+ if (reg) {
+ debug ("PCMCIA powered at %sV\n",
+ (reg&0x0400) ? "5.0" : "3.3");
+ } else {
+ debug ("PCMCIA powered down\n");
+ }
+
+done:
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+ slot+'A');
+ return (0);
+}
+
+#endif /* CCONFIG_PCMCIA */
diff --git a/board/sbc2410x/Makefile b/board/sbc2410x/Makefile
new file mode 100644
index 0000000..ae8665e
--- /dev/null
+++ b/board/sbc2410x/Makefile
@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = lib$(BOARD).a
+
+OBJS := sbc2410x.o flash.o
+SOBJS := lowlevel_init.o
+
+$(LIB): $(OBJS) $(SOBJS)
+ $(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+ $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
diff --git a/board/sbc2410x/config.mk b/board/sbc2410x/config.mk
new file mode 100644
index 0000000..f244e64
--- /dev/null
+++ b/board/sbc2410x/config.mk
@@ -0,0 +1,23 @@
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+#
+# SAMSUNG SMDK2410 board with S3C2410X (ARM920T) cpu
+#
+# see http://www.samsung.com/ for more information on SAMSUNG
+#
+
+#
+# SMDK2410 has 1 bank of 64 MB DRAM
+#
+# 3000'0000 to 3400'0000
+#
+# Linux-Kernel is expected to be at 3000'8000, entry 3000'8000
+# optionally with a ramdisk at 3080'0000
+#
+# we load ourself to 33F8'0000
+#
+# download area is 3300'0000
+
+TEXT_BASE = 0x33F80000
diff --git a/board/sbc2410x/flash.c b/board/sbc2410x/flash.c
new file mode 100644
index 0000000..f2718f2
--- /dev/null
+++ b/board/sbc2410x/flash.c
@@ -0,0 +1,431 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+ulong myflush (void);
+
+#define FLASH_BANK_SIZE PHYS_FLASH_SIZE
+#define MAIN_SECT_SIZE 0x10000 /* 64 KB */
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+#define CMD_READ_ARRAY 0x000000F0
+#define CMD_UNLOCK1 0x000000AA
+#define CMD_UNLOCK2 0x00000055
+#define CMD_ERASE_SETUP 0x00000080
+#define CMD_ERASE_CONFIRM 0x00000030
+#define CMD_PROGRAM 0x000000A0
+#define CMD_UNLOCK_BYPASS 0x00000020
+
+#define MEM_FLASH_ADDR1 (*(volatile u16 *)(CFG_FLASH_BASE + (0x00000555 << 1)))
+#define MEM_FLASH_ADDR2 (*(volatile u16 *)(CFG_FLASH_BASE + (0x000002AA << 1)))
+
+#define BIT_ERASE_DONE 0x00000080
+#define BIT_RDY_MASK 0x00000080
+#define BIT_PROGRAM_ERROR 0x00000020
+#define BIT_TIMEOUT 0x80000000 /* our flag */
+
+#define READY 1
+#define ERR 2
+#define TMO 4
+
+/*-----------------------------------------------------------------------
+ */
+
+ulong flash_init (void)
+{
+ int i, j;
+ ulong size = 0;
+
+ for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+ ulong flashbase = 0;
+
+ flash_info[i].flash_id =
+#if defined(CONFIG_AMD_LV400)
+ (AMD_MANUFACT & FLASH_VENDMASK) |
+ (AMD_ID_LV400B & FLASH_TYPEMASK);
+#elif defined(CONFIG_AMD_LV800)
+ (AMD_MANUFACT & FLASH_VENDMASK) |
+ (AMD_ID_LV800B & FLASH_TYPEMASK);
+#else
+#error "Unknown flash configured"
+#endif
+ flash_info[i].size = FLASH_BANK_SIZE;
+ flash_info[i].sector_count = CFG_MAX_FLASH_SECT;
+ memset (flash_info[i].protect, 0, CFG_MAX_FLASH_SECT);
+ if (i == 0)
+ flashbase = PHYS_FLASH_1;
+ else
+ panic ("configured too many flash banks!\n");
+ for (j = 0; j < flash_info[i].sector_count; j++) {
+ if (j <= 3) {
+ /* 1st one is 16 KB */
+ if (j == 0) {
+ flash_info[i].start[j] =
+ flashbase + 0;
+ }
+
+ /* 2nd and 3rd are both 8 KB */
+ if ((j == 1) || (j == 2)) {
+ flash_info[i].start[j] =
+ flashbase + 0x4000 + (j -
+ 1) *
+ 0x2000;
+ }
+
+ /* 4th 32 KB */
+ if (j == 3) {
+ flash_info[i].start[j] =
+ flashbase + 0x8000;
+ }
+ } else {
+ flash_info[i].start[j] =
+ flashbase + (j - 3) * MAIN_SECT_SIZE;
+ }
+ }
+ size += flash_info[i].size;
+ }
+
+ flash_protect (FLAG_PROTECT_SET,
+ CFG_FLASH_BASE,
+ CFG_FLASH_BASE + monitor_flash_len - 1,
+ &flash_info[0]);
+
+ flash_protect (FLAG_PROTECT_SET,
+ CFG_ENV_ADDR,
+ CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+
+ return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+ int i;
+
+ switch (info->flash_id & FLASH_VENDMASK) {
+ case (AMD_MANUFACT & FLASH_VENDMASK):
+ printf ("AMD: ");
+ break;
+ default:
+ printf ("Unknown Vendor ");
+ break;
+ }
+
+ switch (info->flash_id & FLASH_TYPEMASK) {
+ case (AMD_ID_LV400B & FLASH_TYPEMASK):
+ printf ("1x Amd29LV400BB (4Mbit)\n");
+ break;
+ case (AMD_ID_LV800B & FLASH_TYPEMASK):
+ printf ("1x Amd29LV800BB (8Mbit)\n");
+ break;
+ default:
+ printf ("Unknown Chip Type\n");
+ goto Done;
+ break;
+ }
+
+ printf (" Size: %ld MB in %d Sectors\n",
+ info->size >> 20, info->sector_count);
+
+ printf (" Sector Start Addresses:");
+ for (i = 0; i < info->sector_count; i++) {
+ if ((i % 5) == 0) {
+ printf ("\n ");
+ }
+ printf (" %08lX%s", info->start[i],
+ info->protect[i] ? " (RO)" : " ");
+ }
+ printf ("\n");
+
+ Done:;
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+ ushort result;
+ int iflag, cflag, prot, sect;
+ int rc = ERR_OK;
+ int chip;
+
+ /* first look for protection bits */
+
+ if (info->flash_id == FLASH_UNKNOWN)
+ return ERR_UNKNOWN_FLASH_TYPE;
+
+ if ((s_first < 0) || (s_first > s_last)) {
+ return ERR_INVAL;
+ }
+
+ if ((info->flash_id & FLASH_VENDMASK) !=
+ (AMD_MANUFACT & FLASH_VENDMASK)) {
+ return ERR_UNKNOWN_FLASH_VENDOR;
+ }
+
+ prot = 0;
+ for (sect = s_first; sect <= s_last; ++sect) {
+ if (info->protect[sect]) {
+ prot++;
+ }
+ }
+ if (prot)
+ return ERR_PROTECTED;
+
+ /*
+ * Disable interrupts which might cause a timeout
+ * here. Remember that our exception vectors are
+ * at address 0 in the flash, and we don't want a
+ * (ticker) exception to happen while the flash
+ * chip is in programming mode.
+ */
+ cflag = icache_status ();
+ icache_disable ();
+ iflag = disable_interrupts ();
+
+ /* Start erase on unprotected sectors */
+ for (sect = s_first; sect <= s_last && !ctrlc (); sect++) {
+ printf ("Erasing sector %2d ... ", sect);
+
+ /* arm simple, non interrupt dependent timer */
+ reset_timer_masked ();
+
+ if (info->protect[sect] == 0) { /* not protected */
+ vu_short *addr = (vu_short *) (info->start[sect]);
+
+ MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+ MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+ MEM_FLASH_ADDR1 = CMD_ERASE_SETUP;
+
+ MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+ MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+ *addr = CMD_ERASE_CONFIRM;
+
+ /* wait until flash is ready */
+ chip = 0;
+
+ do {
+ result = *addr;
+
+ /* check timeout */
+ if (get_timer_masked () >
+ CFG_FLASH_ERASE_TOUT) {
+ MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
+ chip = TMO;
+ break;
+ }
+
+ if (!chip
+ && (result & 0xFFFF) & BIT_ERASE_DONE)
+ chip = READY;
+
+ if (!chip
+ && (result & 0xFFFF) & BIT_PROGRAM_ERROR)
+ chip = ERR;
+
+ } while (!chip);
+
+ MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
+
+ if (chip == ERR) {
+ rc = ERR_PROG_ERROR;
+ goto outahere;
+ }
+ if (chip == TMO) {
+ rc = ERR_TIMOUT;
+ goto outahere;
+ }
+
+ printf ("ok.\n");
+ } else { /* it was protected */
+
+ printf ("protected!\n");
+ }
+ }
+
+ if (ctrlc ())
+ printf ("User Interrupt!\n");
+
+ outahere:
+ /* allow flash to settle - wait 10 ms */
+ udelay_masked (10000);
+
+ if (iflag)
+ enable_interrupts ();
+
+ if (cflag)
+ icache_enable ();
+
+ return rc;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash
+ */
+
+volatile static int write_hword (flash_info_t * info, ulong dest, ushort data)
+{
+ vu_short *addr = (vu_short *) dest;
+ ushort result;
+ int rc = ERR_OK;
+ int cflag, iflag;
+ int chip;
+
+ /*
+ * Check if Flash is (sufficiently) erased
+ */
+ result = *addr;
+ if ((result & data) != data)
+ return ERR_NOT_ERASED;
+
+
+ /*
+ * Disable interrupts which might cause a timeout
+ * here. Remember that our exception vectors are
+ * at address 0 in the flash, and we don't want a
+ * (ticker) exception to happen while the flash
+ * chip is in programming mode.
+ */
+ cflag = icache_status ();
+ icache_disable ();
+ iflag = disable_interrupts ();
+
+ MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+ MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+ MEM_FLASH_ADDR1 = CMD_UNLOCK_BYPASS;
+ *addr = CMD_PROGRAM;
+ *addr = data;
+
+ /* arm simple, non interrupt dependent timer */
+ reset_timer_masked ();
+
+ /* wait until flash is ready */
+ chip = 0;
+ do {
+ result = *addr;
+
+ /* check timeout */
+ if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
+ chip = ERR | TMO;
+ break;
+ }
+ if (!chip && ((result & 0x80) == (data & 0x80)))
+ chip = READY;
+
+ if (!chip && ((result & 0xFFFF) & BIT_PROGRAM_ERROR)) {
+ result = *addr;
+
+ if ((result & 0x80) == (data & 0x80))
+ chip = READY;
+ else
+ chip = ERR;
+ }
+
+ } while (!chip);
+
+ *addr = CMD_READ_ARRAY;
+
+ if (chip == ERR || *addr != data)
+ rc = ERR_PROG_ERROR;
+
+ if (iflag)
+ enable_interrupts ();
+
+ if (cflag)
+ icache_enable ();
+
+ return rc;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash.
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+ ulong cp, wp;
+ int l;
+ int i, rc;
+ ushort data;
+
+ wp = (addr & ~1); /* get lower word aligned address */
+
+ /*
+ * handle unaligned start bytes
+ */
+ if ((l = addr - wp) != 0) {
+ data = 0;
+ for (i = 0, cp = wp; i < l; ++i, ++cp) {
+ data = (data >> 8) | (*(uchar *) cp << 8);
+ }
+ for (; i < 2 && cnt > 0; ++i) {
+ data = (data >> 8) | (*src++ << 8);
+ --cnt;
+ ++cp;
+ }
+ for (; cnt == 0 && i < 2; ++i, ++cp) {
+ data = (data >> 8) | (*(uchar *) cp << 8);
+ }
+
+ if ((rc = write_hword (info, wp, data)) != 0) {
+ return (rc);
+ }
+ wp += 2;
+ }
+
+ /*
+ * handle word aligned part
+ */
+ while (cnt >= 2) {
+ data = *((vu_short *) src);
+ if ((rc = write_hword (info, wp, data)) != 0) {
+ return (rc);
+ }
+ src += 2;
+ wp += 2;
+ cnt -= 2;
+ }
+
+ if (cnt == 0) {
+ return ERR_OK;
+ }
+
+ /*
+ * handle unaligned tail bytes
+ */
+ data = 0;
+ for (i = 0, cp = wp; i < 2 && cnt > 0; ++i, ++cp) {
+ data = (data >> 8) | (*src++ << 8);
+ --cnt;
+ }
+ for (; i < 2; ++i, ++cp) {
+ data = (data >> 8) | (*(uchar *) cp << 8);
+ }
+
+ return write_hword (info, wp, data);
+}
diff --git a/board/sbc2410x/lowlevel_init.S b/board/sbc2410x/lowlevel_init.S
new file mode 100644
index 0000000..3df63cd
--- /dev/null
+++ b/board/sbc2410x/lowlevel_init.S
@@ -0,0 +1,163 @@
+/*
+ * Memory Setup stuff - taken from blob memsetup.S
+ *
+ * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl) and
+ * Jan-Derk Bakker (J.D.Bakker@its.tudelft.nl)
+ *
+ * Modified for the Samsung SMDK2410 by
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * Modified for the friendly-arm SBC-2410X by
+ * (C) Copyright 2005
+ * JinHua Luo, GuangDong Linux Center, <luo.jinhua@gd-linux.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+/*
+ * Taken from linux/arch/arm/boot/compressed/head-s3c2410.S
+ *
+ * Copyright (C) 2002 Samsung Electronics SW.LEE <hitchcar@sec.samsung.com>
+ */
+
+#define BWSCON 0x48000000
+
+/* BWSCON */
+#define DW8 (0x0)
+#define DW16 (0x1)
+#define DW32 (0x2)
+#define WAIT (0x1<<2)
+#define UBLB (0x1<<3)
+
+#define B1_BWSCON (DW16)
+#define B2_BWSCON (DW16)
+#define B3_BWSCON (DW16 + WAIT + UBLB)
+#define B4_BWSCON (DW16)
+#define B5_BWSCON (DW16)
+#define B6_BWSCON (DW32)
+#define B7_BWSCON (DW32)
+
+#define B0_Tacs 0x0
+#define B0_Tcos 0x0
+#define B0_Tacc 0x7
+#define B0_Tcoh 0x0
+#define B0_Tah 0x0
+#define B0_Tacp 0x0
+#define B0_PMC 0x0
+
+#define B1_Tacs 0x0
+#define B1_Tcos 0x0
+#define B1_Tacc 0x7
+#define B1_Tcoh 0x0
+#define B1_Tah 0x0
+#define B1_Tacp 0x0
+#define B1_PMC 0x0
+
+#define B2_Tacs 0x0
+#define B2_Tcos 0x0
+#define B2_Tacc 0x7
+#define B2_Tcoh 0x0
+#define B2_Tah 0x0
+#define B2_Tacp 0x0
+#define B2_PMC 0x0
+
+#define B3_Tacs 0xc
+#define B3_Tcos 0x7
+#define B3_Tacc 0xf
+#define B3_Tcoh 0x1
+#define B3_Tah 0x0
+#define B3_Tacp 0x0
+#define B3_PMC 0x0
+
+#define B4_Tacs 0x0
+#define B4_Tcos 0x0
+#define B4_Tacc 0x7
+#define B4_Tcoh 0x0
+#define B4_Tah 0x0
+#define B4_Tacp 0x0
+#define B4_PMC 0x0
+
+#define B5_Tacs 0xc
+#define B5_Tcos 0x7
+#define B5_Tacc 0xf
+#define B5_Tcoh 0x1
+#define B5_Tah 0x0
+#define B5_Tacp 0x0
+#define B5_PMC 0x0
+
+#define B6_MT 0x3 /* SDRAM */
+#define B6_Trcd 0x1
+#define B6_SCAN 0x1 /* 9bit */
+
+#define B7_MT 0x3 /* SDRAM */
+#define B7_Trcd 0x1 /* 3clk */
+#define B7_SCAN 0x1 /* 9bit */
+
+/* REFRESH parameter */
+#define REFEN 0x1 /* Refresh enable */
+#define TREFMD 0x0 /* CBR(CAS before RAS)/Auto refresh */
+#define Trp 0x0 /* 2clk */
+#define Trc 0x3 /* 7clk */
+#define Tchr 0x2 /* 3clk */
+#define REFCNT 0x0459
+/**************************************/
+
+_TEXT_BASE:
+ .word TEXT_BASE
+
+.globl lowlevel_init
+lowlevel_init:
+ /* memory control configuration */
+ /* make r0 relative the current location so that it */
+ /* reads SMRDATA out of FLASH rather than memory ! */
+ ldr r0, =SMRDATA
+ ldr r1, _TEXT_BASE
+ sub r0, r0, r1
+ ldr r1, =BWSCON /* Bus Width Status Controller */
+ add r2, r0, #13*4
+0:
+ ldr r3, [r0], #4
+ str r3, [r1], #4
+ cmp r2, r0
+ bne 0b
+
+ /* everything is fine now */
+ mov pc, lr
+
+ .ltorg
+/* the literal pools origin */
+
+SMRDATA:
+ .word (0+(B1_BWSCON<<4)+(B2_BWSCON<<8)+(B3_BWSCON<<12)+(B4_BWSCON<<16)+(B5_BWSCON<<20)+(B6_BWSCON<<24)+(B7_BWSCON<<28))
+ .word ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC))
+ .word ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC))
+ .word ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC))
+ .word ((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC))
+ .word ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC))
+ .word ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC))
+ .word ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN))
+ .word ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN))
+ .word ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT)
+ .word 0xb2
+ .word 0x30
+ .word 0x30
diff --git a/board/sbc2410x/sbc2410x.c b/board/sbc2410x/sbc2410x.c
new file mode 100644
index 0000000..7030985
--- /dev/null
+++ b/board/sbc2410x/sbc2410x.c
@@ -0,0 +1,183 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2005
+ * JinHua Luo, GuangDong Linux Center, <luo.jinhua@gd-linux.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <s3c2410.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#include <linux/mtd/nand.h>
+#endif
+
+/* ------------------------------------------------------------------------- */
+
+#define FCLK_SPEED 1
+
+#if FCLK_SPEED==0 /* Fout = 203MHz, Fin = 12MHz for Audio */
+#define M_MDIV 0xC3
+#define M_PDIV 0x4
+#define M_SDIV 0x1
+#elif FCLK_SPEED==1 /* Fout = 202.8MHz */
+#define M_MDIV 0x5c
+#define M_PDIV 0x4
+#define M_SDIV 0x0
+#endif
+
+#define USB_CLOCK 1
+
+#if USB_CLOCK==0
+#define U_M_MDIV 0xA1
+#define U_M_PDIV 0x3
+#define U_M_SDIV 0x1
+#elif USB_CLOCK==1
+#define U_M_MDIV 0x48
+#define U_M_PDIV 0x3
+#define U_M_SDIV 0x2
+#endif
+
+static inline void delay (unsigned long loops)
+{
+ __asm__ volatile ("1:\n"
+ "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+ S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER();
+ S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+ /* to reduce PLL lock time, adjust the LOCKTIME register */
+ clk_power->LOCKTIME = 0xFFFFFF;
+
+ /* configure MPLL */
+ clk_power->MPLLCON = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV);
+
+ /* some delay between MPLL and UPLL */
+ delay (4000);
+
+ /* configure UPLL */
+ clk_power->UPLLCON = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV);
+
+ /* some delay between MPLL and UPLL */
+ delay (8000);
+
+ /* set up the I/O ports */
+ gpio->GPACON = 0x007FFFFF;
+ gpio->GPBCON = 0x00044556;
+ gpio->GPBUP = 0x000007FF;
+ gpio->GPCCON = 0xAAAAAAAA;
+ gpio->GPCUP = 0x0000FFFF;
+ gpio->GPDCON = 0xAAAAAAAA;
+ gpio->GPDUP = 0x0000FFFF;
+ gpio->GPECON = 0xAAAAAAAA;
+ gpio->GPEUP = 0x0000FFFF;
+ gpio->GPFCON = 0x000055AA;
+ gpio->GPFUP = 0x000000FF;
+ gpio->GPGCON = 0xFF95FF3A;
+ gpio->GPGUP = 0x0000FFFF;
+ gpio->GPHCON = 0x0016FAAA;
+ gpio->GPHUP = 0x000007FF;
+
+ gpio->EXTINT0=0x22222222;
+ gpio->EXTINT1=0x22222222;
+ gpio->EXTINT2=0x22222222;
+
+ /* arch number of SMDK2410-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_SMDK2410;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0x30000100;
+
+ icache_enable();
+ dcache_enable();
+
+ return 0;
+}
+
+int dram_init (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ return 0;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+extern ulong nand_probe(ulong physadr);
+
+static inline void NF_Reset(void)
+{
+ int i;
+
+ NF_SetCE(NFCE_LOW);
+ NF_Cmd(0xFF); /* reset command */
+ for(i = 0; i < 10; i++); /* tWB = 100ns. */
+ NF_WaitRB(); /* wait 200~500us; */
+ NF_SetCE(NFCE_HIGH);
+}
+
+static inline void NF_Init(void)
+{
+#if 1
+#define TACLS 0
+#define TWRPH0 3
+#define TWRPH1 0
+#else
+#define TACLS 0
+#define TWRPH0 4
+#define TWRPH1 2
+#endif
+
+ NF_Conf((1<<15)|(0<<14)|(0<<13)|(1<<12)|(1<<11)|(TACLS<<8)|(TWRPH0<<4)|(TWRPH1<<0));
+ /*nand->NFCONF = (1<<15)|(1<<14)|(1<<13)|(1<<12)|(1<<11)|(TACLS<<8)|(TWRPH0<<4)|(TWRPH1<<0); */
+ /* 1 1 1 1, 1 xxx, r xxx, r xxx */
+ /* En 512B 4step ECCR nFCE=H tACLS tWRPH0 tWRPH1 */
+
+ NF_Reset();
+}
+
+void nand_init(void)
+{
+ S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
+
+ NF_Init();
+#ifdef DEBUG
+ printf("NAND flash probing at 0x%.8lX\n", (ulong)nand);
+#endif
+ printf ("%4lu MB\n", nand_probe((ulong)nand) >> 20);
+}
+#endif /* CONFIG_COMMANDS & CFG_CMD_NAND */
diff --git a/board/sbc2410x/u-boot.lds b/board/sbc2410x/u-boot.lds
new file mode 100644
index 0000000..76df6b2
--- /dev/null
+++ b/board/sbc2410x/u-boot.lds
@@ -0,0 +1,56 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+/*OUTPUT_FORMAT("elf32-arm", "elf32-arm", "elf32-arm")*/
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/arm920t/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss : { *(.bss) }
+ _end = .;
+}
diff --git a/board/spc1920/Makefile b/board/spc1920/Makefile
new file mode 100644
index 0000000..47afef7
--- /dev/null
+++ b/board/spc1920/Makefile
@@ -0,0 +1,40 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = lib$(BOARD).a
+
+OBJS = $(BOARD).o
+
+$(LIB): .depend $(OBJS)
+ $(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+ $(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################
diff --git a/board/spc1920/config.mk b/board/spc1920/config.mk
new file mode 100644
index 0000000..e361694
--- /dev/null
+++ b/board/spc1920/config.mk
@@ -0,0 +1,35 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Motorola old MPC821/860ADS, MPC8xxFADS, new MPC866ADS, and
+# MPC885ADS boards
+#
+
+#TEXT_BASE = 0xFE000000
+TEXT_BASE = 0xFFF00000
+PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/spc1920
+HOST_CFLAGS += -I$(TOPDIR)/board/spc1920
+HOST_ENVIRO_CFLAGS += -I$(TOPDIR)/board/spc1920
diff --git a/board/spc1920/pld.h b/board/spc1920/pld.h
new file mode 100644
index 0000000..3254f82
--- /dev/null
+++ b/board/spc1920/pld.h
@@ -0,0 +1,14 @@
+#ifndef __PLD_H__
+#define __PLD_H__
+
+typedef struct spc1920_pld {
+ uchar com1_en;
+ uchar dsp_reset;
+ uchar dsp_hpi_on;
+ uchar codec_dsp_power_en;
+ uchar clk2_en;
+ uchar clk3_select;
+ uchar clk4_select;
+} spc1920_pld_t;
+
+#endif /* __PLD_H__ */
diff --git a/board/spc1920/spc1920.c b/board/spc1920/spc1920.c
new file mode 100644
index 0000000..028f4c6
--- /dev/null
+++ b/board/spc1920/spc1920.c
@@ -0,0 +1,236 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <common.h>
+#include <mpc8xx.h>
+#include "pld.h"
+
+#define _NOT_USED_ 0xFFFFFFFF
+/* #define debug(fmt,args...) printf (fmt ,##args) */
+
+static long int dram_size (long int, long int *, long int);
+
+const uint sdram_table[] = {
+ /*
+ * Single Read. (Offset 0 in UPMB RAM)
+ */
+ 0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
+ 0x1FF77C47, /* last */
+ /*
+ * SDRAM Initialization (offset 5 in UPMB RAM)
+ *
+ * This is no UPM entry point. The following definition uses
+ * the remaining space to establish an initialization
+ * sequence, which is executed by a RUN command.
+ *
+ */
+ 0x1FF77C34, 0xEFEABC34, 0x1FB57C35, /* last */
+ /*
+ * Burst Read. (Offset 8 in UPMB RAM)
+ */
+ 0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
+ 0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Single Write. (Offset 18 in UPMB RAM)
+ */
+ 0x1F07FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Burst Write. (Offset 20 in UPMB RAM)
+ */
+ 0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
+ 0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
+ _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Refresh (Offset 30 in UPMB RAM)
+ */
+ 0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+ 0xFFFFFC84, 0xFFFFFC07, /* last */
+ _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /*
+ * Exception. (Offset 3c in UPMB RAM)
+ */
+ 0x7FFFFC07, /* last */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_,
+};
+
+long int initdram (int board_type)
+{
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ volatile memctl8xx_t *memctl = &immr->im_memctl;
+ /* volatile spc1920_pld_t *pld = (spc1920_pld_t *) CFG_SPC1920_PLD_BASE; */
+
+ long int size_b0;
+ long int size8, size9;
+ int i;
+
+ /*
+ * Configure UPMB for SDRAM
+ */
+ upmconfig (UPMB, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
+
+ udelay(100);
+
+ memctl->memc_mptpr = CFG_MPTPR;
+
+ /* burst length=4, burst type=sequential, CAS latency=2 */
+ memctl->memc_mar = CFG_MAR;
+
+ /*
+ * Map controller bank 1 to the SDRAM bank at preliminary address.
+ */
+ memctl->memc_or1 = CFG_OR1_PRELIM;
+ memctl->memc_br1 = CFG_BR1_PRELIM;
+
+ /* initialize memory address register */
+ memctl->memc_mbmr = CFG_MBMR_8COL; /* refresh not enabled yet */
+
+ /* mode initialization (offset 5) */
+ udelay (200); /* 0x80006105 */
+ memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x05);
+
+ /* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
+ udelay (1); /* 0x80006130 */
+ memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
+ udelay (1); /* 0x80006130 */
+ memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
+ udelay (1); /* 0x80006106 */
+ memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x06);
+
+ memctl->memc_mbmr |= MBMR_PTBE; /* refresh enabled */
+
+ udelay (200);
+
+ /* Need at least 10 DRAM accesses to stabilize */
+ for (i = 0; i < 10; ++i) {
+ volatile unsigned long *addr =
+ (volatile unsigned long *) CFG_SDRAM_BASE;
+ unsigned long val;
+
+ val = *(addr + i);
+ *(addr + i) = val;
+ }
+
+ /*
+ * Check Bank 0 Memory Size for re-configuration
+ *
+ * try 8 column mode
+ */
+ size8 = dram_size (CFG_MBMR_8COL, (long *)CFG_SDRAM_BASE, SDRAM_MAX_SIZE);
+
+ udelay (1000);
+
+ /*
+ * try 9 column mode
+ */
+ size9 = dram_size (CFG_MBMR_9COL, (long *)CFG_SDRAM_BASE, SDRAM_MAX_SIZE);
+
+ if (size8 < size9) { /* leave configuration at 9 columns */
+ size_b0 = size9;
+ memctl->memc_mbmr = CFG_MBMR_9COL | MBMR_PTBE;
+ udelay (500);
+ } else { /* back to 8 columns */
+ size_b0 = size8;
+ memctl->memc_mbmr = CFG_MBMR_8COL | MBMR_PTBE;
+ udelay (500);
+ }
+
+ /*
+ * Final mapping:
+ */
+
+ memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) |
+ OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
+ memctl->memc_br1 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V;
+ udelay (1000);
+
+
+ /* PLD Setup */
+ memctl->memc_or5 = CFG_OR5_PRELIM;
+ memctl->memc_br5 = CFG_BR5_PRELIM;
+ udelay(1000);
+
+ return (size_b0);
+}
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+static long int dram_size (long int mbmr_value, long int *base,
+ long int maxsize)
+{
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile memctl8xx_t *memctl = &immap->im_memctl;
+
+ memctl->memc_mbmr = mbmr_value;
+
+ return (get_ram_size (base, maxsize));
+}
+
+
+/************* other stuff ******************/
+
+
+int board_early_init_f(void)
+{
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+
+
+ /* Turn on LED PD9 */
+ immap->im_ioport.iop_pdpar &= ~(0x0040);
+ immap->im_ioport.iop_pddir |= 0x0040;
+ immap->im_ioport.iop_pddat |= 0x0040;
+
+ /* Enable PD10 (COM2_EN) */
+ immap->im_ioport.iop_pdpar &= ~0x0020;
+ immap->im_ioport.iop_pddir &= ~0x4000;
+ immap->im_ioport.iop_pddir |= 0x0020;
+ immap->im_ioport.iop_pddat |= 0x0020;
+
+
+#ifdef CFG_SMC1_PLD_CLK4 /* SMC1 uses CLK4 from PLD */
+ immap->im_cpm.cp_simode |= 0x7000;
+ immap->im_cpm.cp_simode &= ~(0x8000);
+#endif
+
+ return 0;
+}
+
+
+int checkboard (void)
+{
+ puts("Board: SPC1920\n");
+ return 0;
+}
diff --git a/board/spc1920/u-boot.lds b/board/spc1920/u-boot.lds
new file mode 100644
index 0000000..d526d1d
--- /dev/null
+++ b/board/spc1920/u-boot.lds
@@ -0,0 +1,144 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ /* WARNING - the following is hand-optimized to fit within */
+ /* the sector layout of our flash chips! XXX FIXME XXX */
+
+ cpu/mpc8xx/start.o (.text)
+ cpu/mpc8xx/traps.o (.text)
+ common/dlmalloc.o (.text)
+ lib_ppc/ppcstring.o (.text)
+ lib_generic/vsprintf.o (.text)
+ lib_generic/crc32.o (.text)
+ lib_generic/zlib.o (.text)
+ lib_ppc/cache.o (.text)
+ lib_ppc/time.o (.text)
+
+ . = DEFINED(env_offset) ? env_offset : .;
+ common/environment.o (.ppcenv)
+
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ *(.eh_frame)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+ __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
diff --git a/board/tqm5200/Makefile b/board/tqm5200/Makefile
index ab0ff1a..9a1ea48 100644
--- a/board/tqm5200/Makefile
+++ b/board/tqm5200/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS := $(BOARD).o cmd_stk52xx.o
+OBJS := $(BOARD).o cmd_stk52xx.o cmd_tb5200.o
$(LIB): $(OBJS) $(SOBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/tqm5200/cmd_stk52xx.c b/board/tqm5200/cmd_stk52xx.c
index 8b9057f..7af69f2 100755
--- a/board/tqm5200/cmd_stk52xx.c
+++ b/board/tqm5200/cmd_stk52xx.c
@@ -22,7 +22,7 @@
*/
/*
- * SKT52XX specific functions
+ * STK52XX specific functions
*/
/*#define DEBUG*/
@@ -31,6 +31,7 @@
#if (CONFIG_COMMANDS & CFG_CMD_BSP)
+#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
#define DEFAULT_VOL 45
#define DEFAULT_FREQ 500
#define DEFAULT_DURATION 200
@@ -60,7 +61,6 @@
static void pcm1772_write_reg(unsigned char addr, unsigned char data);
static void set_attenuation(unsigned char attenuation);
-#ifdef CONFIG_STK52XX
static void spi_init(void)
{
struct mpc5xxx_spi *spi = (struct mpc5xxx_spi*)MPC5XXX_SPI;
@@ -537,7 +537,9 @@
return rcode;
}
+#endif
+#if defined(CONFIG_STK52XX)
void led_init(void)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
@@ -736,7 +738,9 @@
return 0;
}
+#endif
+#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
/*
* return 1 on CAN initialization failure
* return 0 if no failure
@@ -1106,6 +1110,7 @@
return error_status;
}
+#ifndef CONFIG_FO300
static void sm501_backlight (unsigned int state)
{
if (state == BL_ON) {
@@ -1115,6 +1120,7 @@
*(vu_long *)(SM501_MMIO_BASE+SM501_PANEL_DISPLAY_CONTROL) &=
~((1 << 26) | (1 << 27));
}
+#endif
int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
@@ -1124,7 +1130,9 @@
printf ("Revision 100 of STK52XX not supported!\n");
return 1;
#endif
+#if defined(CONFIG_STK52XX)
led_init();
+#endif
can_init();
switch (argc) {
@@ -1152,6 +1160,7 @@
else
printf ("Error\n");
return rcode;
+#ifndef CONFIG_FO300
} else if (strncmp (argv[1], "backlight", 4) == 0) {
if (strncmp (argv[2], "on", 2) == 0) {
sm501_backlight (BL_ON);
@@ -1161,14 +1170,17 @@
sm501_backlight (BL_OFF);
return 0;
}
+#endif
}
break;
+#if defined(CONFIG_STK52XX)
case 4:
if (strcmp (argv[1], "led") == 0) {
return (do_led (argv));
}
break;
+#endif
default:
break;
@@ -1204,12 +1216,14 @@
"[channel]\n"
" - play short beep on \"l\"eft or \"r\"ight channel\n"
);
+#endif /* CONFIG_STK52XX || CONFIG_FO300 */
+#if defined(CONFIG_STK52XX)
U_BOOT_CMD(
fkt , 4, 1, cmd_fkt,
"fkt - Function test routines\n",
"led number on/off\n"
- " - 'number's like printed on SKT52XX board\n"
+ " - 'number's like printed on STK52XX board\n"
"fkt can\n"
" - loopback plug for X83 required\n"
"fkt rs232 number\n"
@@ -1217,5 +1231,14 @@
"fkt backlight on/off\n"
" - switch backlight on or off\n"
);
-#endif /* CONFIG_STK52XX */
+#elif defined(CONFIG_FO300)
+U_BOOT_CMD(
+ fkt , 3, 1, cmd_fkt,
+ "fkt - Function test routines\n",
+ "fkt can\n"
+ " - loopback plug for X16/X29 required\n"
+ "fkt rs232 number\n"
+ " - loopback plug(s) for X21/X22 required\n"
+);
+#endif
#endif /* CFG_CMD_BSP */
diff --git a/board/tqm5200/cmd_tb5200.c b/board/tqm5200/cmd_tb5200.c
new file mode 100644
index 0000000..8784b1f
--- /dev/null
+++ b/board/tqm5200/cmd_tb5200.c
@@ -0,0 +1,104 @@
+/*
+ * (C) Copyright 2005 - 2006
+ * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * TB5200 specific functions
+ */
+/*#define DEBUG*/
+
+#include <common.h>
+#include <command.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_BSP)
+#if defined (CONFIG_TB5200)
+
+#define SM501_PANEL_DISPLAY_CONTROL 0x00080000UL
+
+static void led_init(void)
+{
+ struct mpc5xxx_gpt_0_7 *gpt = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
+
+ /* configure timer 4 for simple GPIO output */
+ gpt->gpt4.emsr |= 0x00000024;
+}
+
+int cmd_led(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ struct mpc5xxx_gpt_0_7 *gpt = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
+
+ led_init();
+
+ if (strcmp (argv[1], "on") == 0) {
+ debug ("switch status LED on\n");
+ gpt->gpt4.emsr |= (1 << 4);
+ } else if (strcmp (argv[1], "off") == 0) {
+ debug ("switch status LED off\n");
+ gpt->gpt4.emsr &= ~(1 << 4);
+ } else {
+ printf ("Usage:\nled on/off\n");
+ return 1;
+ }
+
+ return 0;
+}
+
+static void sm501_backlight (unsigned int state)
+{
+ if (state == 1) {
+ *(vu_long *)(SM501_MMIO_BASE+SM501_PANEL_DISPLAY_CONTROL) |=
+ (1 << 26) | (1 << 27);
+ } else if (state == 0)
+ *(vu_long *)(SM501_MMIO_BASE+SM501_PANEL_DISPLAY_CONTROL) &=
+ ~((1 << 26) | (1 << 27));
+}
+
+int cmd_backlight(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ if (strcmp (argv[1], "on") == 0) {
+ debug ("switch backlight on\n");
+ sm501_backlight (1);
+ } else if (strcmp (argv[1], "off") == 0) {
+ debug ("switch backlight off\n");
+ sm501_backlight (0);
+ } else {
+ printf ("Usage:\nbacklight on/off\n");
+ return 1;
+ }
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ led , 2, 1, cmd_led,
+ "led - switch status LED on or off\n",
+ "on/off\n"
+);
+
+U_BOOT_CMD(
+ backlight , 2, 1, cmd_backlight,
+ "backlight - switch backlight on or off\n",
+ "on/off\n"
+ );
+
+#endif /* CONFIG_STK52XX */
+#endif /* CFG_CMD_BSP */
diff --git a/board/tqm5200/config.mk b/board/tqm5200/config.mk
index 585a99a..84ddee8 100644
--- a/board/tqm5200/config.mk
+++ b/board/tqm5200/config.mk
@@ -28,12 +28,17 @@
#
# 0xFC000000 boot low (standard configuration with room for max 64 MByte
# Flash ROM)
+# 0xFFF00000 boot high (for a backup copy of U-Boot)
# 0x00100000 boot from RAM (for testing only)
#
+sinclude $(TOPDIR)/board/$(BOARDDIR)/config.tmp
+
ifndef TEXT_BASE
## Standard: boot low
TEXT_BASE = 0xFC000000
+## For a backup copy of U-Boot at the end of flash: boot high
+# TEXT_BASE = 0xFFF00000
## For testing: boot from RAM
# TEXT_BASE = 0x00100000
endif
diff --git a/board/tqm5200/tqm5200.c b/board/tqm5200/tqm5200.c
index 310abd2..c8350ab 100644
--- a/board/tqm5200/tqm5200.c
+++ b/board/tqm5200/tqm5200.c
@@ -1,11 +1,11 @@
/*
- * (C) Copyright 2003-2004
+ * (C) Copyright 2003-2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2004
* Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
*
- * (C) Copyright 2004-2005
+ * (C) Copyright 2004-2006
* Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
*
* See file CREDITS for list of people who contributed to this
@@ -30,6 +30,7 @@
#include <common.h>
#include <mpc5xxx.h>
#include <pci.h>
+#include <asm/processor.h>
#ifdef CONFIG_VIDEO_SM501
#include <sm501.h>
@@ -101,6 +102,8 @@
{
ulong dramsize = 0;
ulong dramsize2 = 0;
+ uint svr, pvr;
+
#ifndef CFG_RAMBOOT
ulong test1, test2;
@@ -190,11 +193,31 @@
} else {
dramsize2 = 0;
}
-
#endif /* CFG_RAMBOOT */
-/* return dramsize + dramsize2; */
+ /*
+ * On MPC5200B we need to set the special configuration delay in the
+ * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
+ * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
+ *
+ * "The SDelay should be written to a value of 0x00000004. It is
+ * required to account for changes caused by normal wafer processing
+ * parameters."
+ */
+ svr = get_svr();
+ pvr = get_pvr();
+ if ((SVR_MJREV(svr) >= 2) &&
+ (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
+
+ *(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
+ __asm__ volatile ("sync");
+ }
+
+#if defined(CONFIG_TQM5200_B)
+ return dramsize + dramsize2;
+#else
return dramsize;
+#endif /* CONFIG_TQM5200_B */
}
#elif defined(CONFIG_MGT5100)
@@ -250,20 +273,38 @@
int checkboard (void)
{
-#if defined (CONFIG_AEVFIFO)
+#if defined(CONFIG_AEVFIFO)
puts ("Board: AEVFIFO\n");
return 0;
#endif
-#if defined (CONFIG_TQM5200)
- puts ("Board: TQM5200 (TQ-Components GmbH)\n");
+
+#if defined(CONFIG_TQM5200S)
+# define MODULE_NAME "TQM5200S"
+#else
+# define MODULE_NAME "TQM5200"
#endif
-#if defined (CONFIG_STK52XX)
- puts (" on a STK52XX baseboard\n");
+
+#if defined(CONFIG_STK52XX)
+# define CARRIER_NAME "STK52xx"
+#elif defined(CONFIG_TB5200)
+# define CARRIER_NAME "TB5200"
+#elif defined(CONFIG_CAM5200)
+# define CARRIER_NAME "Cam5200"
+#elif defined(CONFIG_FO300)
+# define CARRIER_NAME "FO300"
+#else
+# error "UNKNOWN"
#endif
+ puts ( "Board: " MODULE_NAME " (TQ-Components GmbH)\n"
+ " on a " CARRIER_NAME " carrier board\n");
+
return 0;
}
+#undef MODULE_NAME
+#undef CARRIER_NAME
+
void flash_preinit(void)
{
/*
@@ -405,7 +446,6 @@
#endif
#endif /* CONFIG_PS2MULT */
-#if defined(CONFIG_CS_AUTOCONF)
int last_stage_init (void)
{
/*
@@ -500,11 +540,14 @@
return 0;
}
-#endif /* CONFIG_CS_AUTOCONF */
#ifdef CONFIG_VIDEO_SM501
+#ifdef CONFIG_FO300
+#define DISPLAY_WIDTH 800
+#else
#define DISPLAY_WIDTH 640
+#endif
#define DISPLAY_HEIGHT 480
#ifdef CONFIG_VIDEO_SM501_8BPP
@@ -534,6 +577,28 @@
{0x80218, 0x000201e9},
{0x80200, 0x00013306},
#else /* panel + CRT */
+#ifdef CONFIG_FO300
+ {0x00004, 0x0},
+ {0x00048, 0x00021807},
+ {0x0004C, 0x301a0a01},
+ {0x00054, 0x1},
+ {0x00040, 0x00021807},
+ {0x00044, 0x091a0a01},
+ {0x00054, 0x0},
+ {0x80000, 0x0f013106},
+ {0x80004, 0xc428bb17},
+ {0x8000C, 0x00000000},
+ {0x80010, 0x0C800C80},
+ {0x80014, 0x03200000},
+ {0x80018, 0x01e00000},
+ {0x8001C, 0x00000000},
+ {0x80020, 0x01e00320},
+ {0x80024, 0x042a031f},
+ {0x80028, 0x0086034a},
+ {0x8002C, 0x020c01df},
+ {0x80030, 0x000201ea},
+ {0x80200, 0x00010000},
+#else
{0x00004, 0x0},
{0x00048, 0x00021807},
{0x0004C, 0x091a0a01},
@@ -554,6 +619,7 @@
{0x8002C, 0x020c01df},
{0x80030, 0x000201e9},
{0x80200, 0x00010000},
+#endif /* #ifdef CONFIG_FO300 */
#endif
{0, 0}
};
@@ -567,9 +633,17 @@
{
if (line_number == 1) {
strcpy (info, " Board: TQM5200 (TQ-Components GmbH)");
-#if defined (CONFIG_STK52XX)
+#if defined (CONFIG_STK52XX) || defined (CONFIG_TB5200) || defined(CONFIG_FO300)
} else if (line_number == 2) {
- strcpy (info, " on a STK52XX baseboard");
+#if defined (CONFIG_STK52XX)
+ strcpy (info, " on a STK52xx carrier board");
+#endif
+#if defined (CONFIG_TB5200)
+ strcpy (info, " on a TB5200 carrier board");
+#endif
+#if defined (CONFIG_FO300)
+ strcpy (info, " on a FO300 carrier board");
+#endif
#endif
}
else {
@@ -655,3 +729,33 @@
}
#endif /* CONFIG_VIDEO_SM501 */
+
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+#ifdef CONFIG_FO300
+int board_early_init_f (void)
+{
+ vu_long timer3_status;
+ DECLARE_GLOBAL_DATA_PTR;
+
+ /* Configure GPT3 as GPIO input */
+ *(vu_long *)MPC5XXX_GPT3_ENABLE = 0x00000004;
+
+ /* Read in TIMER_3 pin status */
+ timer3_status = *(vu_long *)MPC5XXX_GPT3_STATUS;
+
+#ifdef FO300_SILENT_CONSOLE_WHEN_S1_CLOSED
+ /* Force silent console mode if S1 switch
+ * is in closed position (TIMER_3 pin status is LOW). */
+ if (MPC5XXX_GPT_GPIO_PIN(timer3_status) == 0)
+#else
+ /* Force silent console mode if S1 switch
+ * is in open position (TIMER_3 pin status is HIGH). */
+ if (MPC5XXX_GPT_GPIO_PIN(timer3_status) == 1)
+#endif
+ gd->flags |= GD_FLG_SILENT;
+
+ return 0;
+}
+#endif
+#endif
diff --git a/board/tqm834x/tqm834x.c b/board/tqm834x/tqm834x.c
index d992aec..41b34cc 100644
--- a/board/tqm834x/tqm834x.c
+++ b/board/tqm834x/tqm834x.c
@@ -424,10 +424,12 @@
* which has to be written with a certain value defined by
* errata sheet.
*/
+ u32 *reserved_p = (u32 *)((u8 *)im + 0x2f00);
+
#if defined(DDR_CASLAT_20)
- *((u8 *)im + 0x2f00) = 0x201c0000;
+ *reserved_p = 0x201c0000;
#else
- *((u8 *)im + 0x2f00) = 0x202c0000;
+ *reserved_p = 0x202c0000;
#endif
}
}
diff --git a/board/tqm85xx/tqm85xx.c b/board/tqm85xx/tqm85xx.c
index befe8b7..b4ef5af 100644
--- a/board/tqm85xx/tqm85xx.c
+++ b/board/tqm85xx/tqm85xx.c
@@ -27,10 +27,6 @@
* MA 02111-1307 USA
*/
-#ifdef CONFIG_PS2MULT
-void ps2mult_early_init(void);
-#endif
-
#include <common.h>
#include <pci.h>
#include <asm/processor.h>
@@ -47,6 +43,10 @@
long int fixed_sdram (void);
ulong flash_get_size (ulong base, int banknum);
+#ifdef CONFIG_PS2MULT
+void ps2mult_early_init(void);
+#endif
+
#ifdef CONFIG_CPM2
/*
* I/O Port configuration table
@@ -423,4 +423,3 @@
return (0);
}
#endif /* CONFIG_BOARD_EARLY_INIT_R */
-
diff --git a/board/tqm8xx/flash.c b/board/tqm8xx/flash.c
index ab57ee5..db0a7e5 100644
--- a/board/tqm8xx/flash.c
+++ b/board/tqm8xx/flash.c
@@ -33,12 +33,13 @@
DECLARE_GLOBAL_DATA_PTR;
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M)
+#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) \
+ && !defined(CONFIG_TQM885D)
# ifndef CFG_OR_TIMING_FLASH_AT_50MHZ
# define CFG_OR_TIMING_FLASH_AT_50MHZ (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
OR_SCY_2_CLK | OR_EHTR | OR_BI)
# endif
-#endif /* CONFIG_TQM8xxL/M, !TQM866M */
+#endif /* CONFIG_TQM8xxL/M, !TQM866M, !TQM885D */
#ifndef CFG_ENV_ADDR
#define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_ENV_OFFSET)
diff --git a/board/tqm8xx/tqm8xx.c b/board/tqm8xx/tqm8xx.c
index b292231..6b206f8 100644
--- a/board/tqm8xx/tqm8xx.c
+++ b/board/tqm8xx/tqm8xx.c
@@ -119,6 +119,10 @@
gd->board_type = 'M';
}
+ if ((*(s + 6) == 'D')) { /* a TQM885D type */
+ gd->board_type = 'D';
+ }
+
for (; *s; ++s) {
if (*s == ' ')
break;
@@ -178,7 +182,8 @@
#ifndef CONFIG_CAN_DRIVER
if ((board_type != 'L') &&
- (board_type != 'M') ) { /* "L" and "M" type boards have only one bank SDRAM */
+ (board_type != 'M') &&
+ (board_type != 'D') ) { /* "L" and "M" type boards have only one bank SDRAM */
memctl->memc_or3 = CFG_OR3_PRELIM;
memctl->memc_br3 = CFG_BR3_PRELIM;
}
@@ -197,7 +202,8 @@
#ifndef CONFIG_CAN_DRIVER
if ((board_type != 'L') &&
- (board_type != 'M') ) { /* "L" and "M" type boards have only one bank SDRAM */
+ (board_type != 'M') &&
+ (board_type != 'D') ) { /* only one SDRAM bank on L, M and D modules */
memctl->memc_mcr = 0x80006105; /* SDRAM bank 1 */
udelay (1);
memctl->memc_mcr = 0x80006230; /* SDRAM bank 1 - execute twice */
@@ -214,8 +220,7 @@
*
* try 8 column mode
*/
- size8 = dram_size (CFG_MAMR_8COL, SDRAM_BASE2_PRELIM,
- SDRAM_MAX_SIZE);
+ size8 = dram_size (CFG_MAMR_8COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size8 >> 20);
udelay (1000);
@@ -223,8 +228,7 @@
/*
* try 9 column mode
*/
- size9 = dram_size (CFG_MAMR_9COL, SDRAM_BASE2_PRELIM,
- SDRAM_MAX_SIZE);
+ size9 = dram_size (CFG_MAMR_9COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size9 >> 20);
udelay(1000);
@@ -233,8 +237,7 @@
/*
* try 10 column mode
*/
- size10 = dram_size (CFG_MAMR_10COL, (ulong *) SDRAM_BASE2_PRELIM,
- SDRAM_MAX_SIZE);
+ size10 = dram_size (CFG_MAMR_10COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
debug ("SDRAM Bank 0 in 10 column mode: %ld MB\n", size10 >> 20);
#else
size10 = 0;
@@ -255,7 +258,8 @@
#ifndef CONFIG_CAN_DRIVER
if ((board_type != 'L') &&
- (board_type != 'M') ) { /* "L" and "M" type boards have only one bank SDRAM */
+ (board_type != 'M') &&
+ (board_type != 'D') ) { /* "L" and "M" type boards have only one bank SDRAM */
/*
* Check Bank 1 Memory Size
* use current column settings
diff --git a/board/trab/auto_update.c b/board/trab/auto_update.c
index 056e562..d2c8d44 100644
--- a/board/trab/auto_update.c
+++ b/board/trab/auto_update.c
@@ -57,9 +57,9 @@
* valid then run it.
* 2) if preinst.img is found load it into memory. If it is
* valid then run it. Update the EEPROM.
- * 3) if firmware.img is found load it into memory. If it is valid,
+ * 3) if firmw_01.img is found load it into memory. If it is valid,
* burn it into FLASH and update the EEPROM.
- * 4) if kernel.img is found load it into memory. If it is valid,
+ * 4) if kernl_01.img is found load it into memory. If it is valid,
* burn it into FLASH and update the EEPROM.
* 5) if app.img is found load it into memory. If it is valid,
* burn it into FLASH and update the EEPROM.
@@ -81,8 +81,8 @@
/* possible names of files on the USB stick. */
#define AU_PREPARE "prepare.img"
#define AU_PREINST "preinst.img"
-#define AU_FIRMWARE "firmware.img"
-#define AU_KERNEL "kernel.img"
+#define AU_FIRMWARE "firmw_01.img"
+#define AU_KERNEL "kernl_01.img"
#define AU_APP "app.img"
#define AU_DISK "disk.img"
#define AU_POSTINST "postinst.img"
@@ -222,7 +222,7 @@
/* check the data CRC */
checksum = ntohl(hdr->ih_dcrc);
- if (crc32 (0, (char *)(LOAD_ADDR + sizeof(*hdr)), ntohl(hdr->ih_size))
+ if (crc32 (0, (uchar *)(LOAD_ADDR + sizeof(*hdr)), ntohl(hdr->ih_size))
!= checksum)
{
printf ("Image %s bad data checksum\n", aufile[idx]);
@@ -261,7 +261,7 @@
checksum = ntohl(hdr->ih_hcrc);
hdr->ih_hcrc = 0;
- if (crc32 (0, (char *)hdr, sizeof(*hdr)) != checksum) {
+ if (crc32 (0, (uchar *)hdr, sizeof(*hdr)) != checksum) {
printf ("Image %s bad header checksum\n", aufile[idx]);
return -1;
}
@@ -397,7 +397,7 @@
}
/* check the dcrc of the copy */
- if (crc32 (0, (char *)(start + off), ntohl(hdr->ih_size)) != ntohl(hdr->ih_dcrc)) {
+ if (crc32 (0, (uchar *)(start + off), ntohl(hdr->ih_size)) != ntohl(hdr->ih_dcrc)) {
printf ("Image %s Bad Data Checksum After COPY\n", aufile[idx]);
return -1;
}
@@ -613,7 +613,8 @@
#define VFD_LOGO_WIDTH 112
#define VFD_LOGO_HEIGHT 72
/* must call transfer_pic directly */
- transfer_pic(3, env, VFD_LOGO_HEIGHT, VFD_LOGO_WIDTH);
+ transfer_pic(3, (unsigned char *)env,
+ VFD_LOGO_HEIGHT, VFD_LOGO_WIDTH);
}
bitmap_first = 1;
}
diff --git a/board/trab/cmd_trab.c b/board/trab/cmd_trab.c
index edea8f0..b82c8ed 100644
--- a/board/trab/cmd_trab.c
+++ b/board/trab/cmd_trab.c
@@ -147,11 +147,11 @@
u16 pass_cycles;
u16 first_error_cycle;
u8 first_error_num;
-unsigned char first_error_name[16];
+char first_error_name[16];
u16 act_cycle;
typedef struct test_function_s {
- unsigned char *name;
+ char *name;
int (*pf)(void);
} test_function_t;
@@ -376,7 +376,7 @@
return (1);
}
if (i2c_read_multiple (I2C_EEPROM_DEV_ADDR, EE_ADDR_FIRST_ERROR_NAME,
- 1, first_error_name,
+ 1, (unsigned char*)first_error_name,
sizeof (first_error_name))) {
return (1);
}
@@ -537,7 +537,7 @@
/* write test string 1, read back and verify */
if (i2c_write_multiple (I2C_EEPROM_DEV_ADDR, EE_ADDR_TEST, 1,
- EEPROM_TEST_STRING_1,
+ (unsigned char*)EEPROM_TEST_STRING_1,
sizeof (EEPROM_TEST_STRING_1))) {
return (1);
}
@@ -547,7 +547,7 @@
return (1);
}
- if (strcmp (temp, EEPROM_TEST_STRING_1) != 0) {
+ if (strcmp ((char *)temp, EEPROM_TEST_STRING_1) != 0) {
result = 1;
printf ("%s: error; read_str = \"%s\"\n", __FUNCTION__, temp);
}
@@ -555,7 +555,7 @@
/* write test string 2, read back and verify */
if (result == 0) {
if (i2c_write_multiple (I2C_EEPROM_DEV_ADDR, EE_ADDR_TEST, 1,
- EEPROM_TEST_STRING_2,
+ (unsigned char*)EEPROM_TEST_STRING_2,
sizeof (EEPROM_TEST_STRING_2))) {
return (1);
}
@@ -565,7 +565,7 @@
return (1);
}
- if (strcmp (temp, EEPROM_TEST_STRING_2) != 0) {
+ if (strcmp ((char *)temp, EEPROM_TEST_STRING_2) != 0) {
result = 1;
printf ("%s: error; read str = \"%s\"\n",
__FUNCTION__, temp);
@@ -777,7 +777,7 @@
return (1);
}
if (i2c_write_multiple (I2C_EEPROM_DEV_ADDR, EE_ADDR_FIRST_ERROR_NAME,
- 1, first_error_name,
+ 1, (unsigned char*) first_error_name,
sizeof(first_error_name))) {
return (1);
}
diff --git a/board/trab/flash.c b/board/trab/flash.c
index 8cdd824..3e8f105 100644
--- a/board/trab/flash.c
+++ b/board/trab/flash.c
@@ -281,10 +281,12 @@
if (chip1 == ERR || chip2 == ERR) {
rc = ERR_PROG_ERROR;
+ printf ("Flash erase error\n");
goto outahere;
}
if (chip1 == TMO) {
rc = ERR_TIMOUT;
+ printf ("Flash erase timeout error\n");
goto outahere;
}
}
@@ -340,7 +342,9 @@
#endif
iflag = disable_interrupts ();
- *addr = CMD_PROGRAM;
+ MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+ MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+ MEM_FLASH_ADDR1 = CMD_PROGRAM;
*addr = data;
/* arm simple, non interrupt dependent timer */
@@ -352,7 +356,7 @@
result = *addr;
/* check timeout */
- if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
+ if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
chip1 = ERR | TMO;
break;
}
@@ -384,8 +388,13 @@
*addr = CMD_READ_ARRAY;
- if (chip1 == ERR || chip2 == ERR || *addr != data)
+ if (chip1 == ERR || chip2 == ERR || *addr != data) {
rc = ERR_PROG_ERROR;
+ printf ("Flash program error\n");
+ debug ("chip1: %#x, chip2: %#x, addr: %#lx *addr: %#lx, "
+ "data: %#lx\n",
+ chip1, chip2, addr, *addr, data);
+ }
if (iflag)
enable_interrupts ();
@@ -408,10 +417,6 @@
int l;
int i, rc;
- MEM_FLASH_ADDR1 = CMD_UNLOCK1;
- MEM_FLASH_ADDR2 = CMD_UNLOCK2;
- MEM_FLASH_ADDR1 = CMD_UNLOCK_BYPASS;
-
wp = (addr & ~3); /* get lower word aligned address */
/*
@@ -479,9 +484,6 @@
Done:
- MEM_FLASH_ADDR = CMD_UNLOCK_BYPASS_RES1;
- MEM_FLASH_ADDR = CMD_UNLOCK_BYPASS_RES2;
-
return (rc);
}
@@ -515,7 +517,7 @@
info->flash_id = FLASH_UNKNOWN;
info->sector_count = 0;
info->size = 0;
- addr[0] = 0x00FF00FF; /* restore read mode */
+ addr[0] = CMD_READ_ARRAY; /* restore read mode */
debug ("## flash_init: unknown manufacturer\n");
return (0); /* no or unknown flash */
}
@@ -530,7 +532,7 @@
info->sector_count = 71;
info->size = 0x00800000;
- addr[0] = 0x00FF00FF; /* restore read mode */
+ addr[0] = CMD_READ_ARRAY; /* restore read mode */
break; /* => 8 MB */
case AMD_ID_LV640U:
@@ -538,7 +540,7 @@
info->sector_count = 128;
info->size = 0x01000000;
- addr[0] = 0x00F000F0; /* restore read mode */
+ addr[0] = CMD_READ_ARRAY; /* restore read mode */
break; /* => 16 MB */
case MX_ID_LV320B:
@@ -546,13 +548,13 @@
info->sector_count = 71;
info->size = 0x00800000;
- addr[0] = 0x00FF00FF; /* restore read mode */
+ addr[0] = CMD_READ_ARRAY; /* restore read mode */
break; /* => 8 MB */
default:
debug ("## flash_init: unknown flash chip\n");
info->flash_id = FLASH_UNKNOWN;
- addr[0] = 0x00FF00FF; /* restore read mode */
+ addr[0] = CMD_READ_ARRAY; /* restore read mode */
return (0); /* => no or unknown flash */
}
diff --git a/board/trab/memory.c b/board/trab/memory.c
index 4097892..58bd995 100644
--- a/board/trab/memory.c
+++ b/board/trab/memory.c
@@ -419,14 +419,14 @@
int ret = 0;
if (ret == 0)
- ret = memory_post_dataline ((long long *)start);
+ ret = memory_post_dataline ((unsigned long long *)start);
WATCHDOG_RESET ();
if (ret == 0)
- ret = memory_post_addrline ((long *)start, (long *)start, size);
+ ret = memory_post_addrline ((ulong *)start, (ulong *)start, size);
WATCHDOG_RESET ();
if (ret == 0)
- ret = memory_post_addrline ((long *)(start + size - 8),
- (long *)start, size);
+ ret = memory_post_addrline ((ulong *)(start + size - 8),
+ (ulong *)start, size);
WATCHDOG_RESET ();
if (ret == 0)
ret = memory_post_test1 (start, size, 0x00000000);
diff --git a/board/trab/trab.c b/board/trab/trab.c
index 346406e..d8a726b 100644
--- a/board/trab/trab.c
+++ b/board/trab/trab.c
@@ -152,13 +152,13 @@
#define KBD_DATA (((*(volatile ulong *)0x04020000) >> 16) & 0xF)
-static uchar *key_match (ulong);
+static char *key_match (ulong);
int misc_init_r (void)
{
ulong kbd_data = KBD_DATA;
- uchar keybd_env[KEYBD_KEY_NUM + 1];
- uchar *str;
+ char *str;
+ char keybd_env[KEYBD_KEY_NUM + 1];
int i;
#ifdef CONFIG_VERSION_VARIABLE
@@ -175,9 +175,11 @@
#endif /* CONFIG_VERSION_VARIABLE */
#ifdef CONFIG_AUTO_UPDATE
- extern int do_auto_update(void);
- /* this has priority over all else */
- do_auto_update();
+ {
+ extern int do_auto_update(void);
+ /* this has priority over all else */
+ do_auto_update();
+ }
#endif
for (i = 0; i < KEYBD_KEY_NUM; ++i) {
@@ -208,7 +210,7 @@
static uchar kbd_magic_prefix[] = "key_magic";
static uchar kbd_command_prefix[] = "key_cmd";
-static int compare_magic (ulong kbd_data, uchar *str)
+static int compare_magic (ulong kbd_data, char *str)
{
uchar key_mask;
@@ -254,12 +256,12 @@
* Note: the string points to static environment data and must be
* saved before you call any function that modifies the environment.
*/
-static uchar *key_match (ulong kbd_data)
+static char *key_match (ulong kbd_data)
{
- uchar magic[sizeof (kbd_magic_prefix) + 1];
- uchar cmd_name[sizeof (kbd_command_prefix) + 1];
- uchar *suffix;
- uchar *kbd_magic_keys;
+ char magic[sizeof (kbd_magic_prefix) + 1];
+ char cmd_name[sizeof (kbd_command_prefix) + 1];
+ char *suffix;
+ char *kbd_magic_keys;
/*
* The following string defines the characters that can pe appended
@@ -304,7 +306,7 @@
int do_kbd (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
ulong kbd_data = KBD_DATA;
- uchar keybd_env[KEYBD_KEY_NUM + 1];
+ char keybd_env[KEYBD_KEY_NUM + 1];
int i;
puts ("Keys:");
@@ -404,7 +406,7 @@
static void tsc2000_set_brightness(void)
{
- uchar tmp[10];
+ char tmp[10];
int i, br;
spi_init();
diff --git a/board/trab/trab_fkt.c b/board/trab/trab_fkt.c
index abb3b29..71be6e0 100644
--- a/board/trab/trab_fkt.c
+++ b/board/trab/trab_fkt.c
@@ -967,21 +967,21 @@
if (calib_point == CALIB_TL) {
if (i2c_write_multiple (I2C_EEPROM_DEV_ADDR, TOUCH_X0, 1,
- (char *)&x, 2)) {
+ (unsigned char *)&x, 2)) {
return 1;
}
if (i2c_write_multiple (I2C_EEPROM_DEV_ADDR, TOUCH_Y0, 1,
- (char *)&y, 2)) {
+ (unsigned char *)&y, 2)) {
return 1;
}
/* verify written values */
if (i2c_read_multiple (I2C_EEPROM_DEV_ADDR, TOUCH_X0, 1,
- (char *)&x_verify, 2)) {
+ (unsigned char *)&x_verify, 2)) {
return 1;
}
if (i2c_read_multiple (I2C_EEPROM_DEV_ADDR, TOUCH_Y0, 1,
- (char *)&y_verify, 2)) {
+ (unsigned char *)&y_verify, 2)) {
return 1;
}
if ((y != y_verify) || (x != x_verify)) {
@@ -993,21 +993,21 @@
}
else if (calib_point == CALIB_DR) {
if (i2c_write_multiple (I2C_EEPROM_DEV_ADDR, TOUCH_X1, 1,
- (char *)&x, 2)) {
+ (unsigned char *)&x, 2)) {
return 1;
}
if (i2c_write_multiple (I2C_EEPROM_DEV_ADDR, TOUCH_Y1, 1,
- (char *)&y, 2)) {
+ (unsigned char *)&y, 2)) {
return 1;
}
/* verify written values */
if (i2c_read_multiple (I2C_EEPROM_DEV_ADDR, TOUCH_X1, 1,
- (char *)&x_verify, 2)) {
+ (unsigned char *)&x_verify, 2)) {
return 1;
}
if (i2c_read_multiple (I2C_EEPROM_DEV_ADDR, TOUCH_Y1, 1,
- (char *)&y_verify, 2)) {
+ (unsigned char *)&y_verify, 2)) {
return 1;
}
if ((y != y_verify) || (x != x_verify)) {
@@ -1110,7 +1110,7 @@
if (strcmp (argv[2], "read") == 0) {
if (i2c_read (I2C_EEPROM_DEV_ADDR, SERIAL_NUMBER, 1,
- (char *)&serial_number, 4)) {
+ (unsigned char *)&serial_number, 4)) {
printf ("could not read from eeprom\n");
return (1);
}
@@ -1121,7 +1121,7 @@
else if (strcmp (argv[2], "write") == 0) {
serial_number = simple_strtoul(argv[3], NULL, 10);
if (i2c_write (I2C_EEPROM_DEV_ADDR, SERIAL_NUMBER, 1,
- (char *)&serial_number, 4)) {
+ (unsigned char *)&serial_number, 4)) {
printf ("could not write to eeprom\n");
return (1);
}
@@ -1141,7 +1141,7 @@
{
#if (CONFIG_COMMANDS & CFG_CMD_I2C)
int crc;
- char buf[EEPROM_MAX_CRC_BUF];
+ unsigned char buf[EEPROM_MAX_CRC_BUF];
if (i2c_read (I2C_EEPROM_DEV_ADDR, 0, 1, buf, 60)) {
printf ("could not read from eeprom\n");
@@ -1153,7 +1153,7 @@
print_identifier ();
printf ("crc16=%#04x\n", crc);
- if (i2c_write (I2C_EEPROM_DEV_ADDR, CRC16, 1, (char *)&crc,
+ if (i2c_write (I2C_EEPROM_DEV_ADDR, CRC16, 1, (unsigned char *)&crc,
sizeof (crc))) {
printf ("could not read from eeprom\n");
return (1);
diff --git a/board/trab/vfd.c b/board/trab/vfd.c
index 2f1e7d7..b6798fd 100644
--- a/board/trab/vfd.c
+++ b/board/trab/vfd.c
@@ -251,19 +251,17 @@
unsigned long adr = gd->fb_base;
unsigned int bit_nr = 0;
- if (vfd_table[x][y][color][display][entry]) {
+ pixel = vfd_table[x][y][color][display][entry] + frame_buf_offs;
+ /*
+ * wrap arround if offset
+ * (see manual S3C2400)
+ */
+ if (pixel>=FRAME_BUF_SIZE*8)
+ pixel = pixel-(FRAME_BUF_SIZE*8);
+ adr = gd->fb_base+(pixel/32)*4+(3-(pixel%32)/8);
+ bit_nr = pixel%8;
+ bit_nr = (bit_nr>3)?bit_nr-4:bit_nr+4;
- pixel = vfd_table[x][y][color][display][entry] + frame_buf_offs;
- /*
- * wrap arround if offset
- * (see manual S3C2400)
- */
- if (pixel>=FRAME_BUF_SIZE*8)
- pixel = pixel-(FRAME_BUF_SIZE*8);
- adr = gd->fb_base+(pixel/32)*4+(3-(pixel%32)/8);
- bit_nr = pixel%8;
- bit_nr = (bit_nr>3)?bit_nr-4:bit_nr+4;
- }
adr_vfd_table[x][y][color][display][entry] = adr;
bit_vfd_table[x][y][color][display][entry] = bit_nr;
}
diff --git a/board/uc100/Makefile b/board/uc100/Makefile
index eb81625..2d2cc23 100644
--- a/board/uc100/Makefile
+++ b/board/uc100/Makefile
@@ -25,8 +25,8 @@
LIB = lib$(BOARD).a
-#OBJS = $(BOARD).o flash.o
-OBJS = $(BOARD).o
+#OBJS = $(BOARD).o flash.o pcmcia.o
+OBJS = $(BOARD).o pcmcia.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/uc100/pcmcia.c b/board/uc100/pcmcia.c
new file mode 100644
index 0000000..6e4b6d6
--- /dev/null
+++ b/board/uc100/pcmcia.c
@@ -0,0 +1,198 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#ifdef CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "UC100"
+
+/*
+ * Remark: don't turn off OE "__MY_PCMCIA_GCRX_CXOE" on UC100 board.
+ * This leads to board-hangup! (sr, 8 Dez. 2004)
+ */
+static void cfg_ports (void)
+{
+ volatile immap_t *immap;
+
+ immap = (immap_t *)CFG_IMMR;
+
+ /*
+ * Configure Port A for MAX1602 PC-Card Power-Interface Switch
+ */
+ immap->im_ioport.iop_padat &= ~0x8000; /* set port x output to low */
+ immap->im_ioport.iop_padir |= 0x8000; /* enable port x as output */
+
+ debug ("Set Port A: PAR: %08x DIR: %08x DAT: %08x\n",
+ immap->im_ioport.iop_papar, immap->im_ioport.iop_padir,
+ immap->im_ioport.iop_padat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ volatile sysconf8xx_t *sysp;
+ uint reg, mask;
+
+ debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ udelay(10000);
+
+ immap = (immap_t *)CFG_IMMR;
+ sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+ /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+ cfg_ports ();
+
+ /*
+ * Configure SIUMCR to enable PCMCIA port B
+ * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+ */
+ sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
+ pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Make sure there is a card in the slot, then configure the interface.
+ */
+ udelay(10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n",
+ __LINE__,__FUNCTION__,
+ &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+ if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ /*
+ * Power On.
+ */
+ mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+ reg = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+ reg,
+ (reg&PCMCIA_VS1(slot))?"n":"ff",
+ (reg&PCMCIA_VS2(slot))?"n":"ff");
+ if ((reg & mask) == mask) {
+ puts (" 5.0V card found: ");
+ } else {
+ puts (" 3.3V card found: ");
+ }
+
+ /* switch VCC on */
+ immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */
+
+ udelay(10000);
+
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ volatile immap_t *immap;
+ volatile cpm8xx_t *cp;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+ /* switch VCC off */
+ immap->im_ioport.iop_padat &= ~0x8000; /* power disable 3.3V */
+
+ /* Configure PCMCIA General Control Register */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ PCMCIA_PGCRX(_slot_) = reg;
+
+ udelay(10000);
+
+ return (0);
+}
+#endif /* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+ volatile immap_t *immap;
+ volatile pcmconf8xx_t *pcmp;
+ u_long reg;
+
+ debug ("voltage_set: "
+ PCMCIA_BOARD_MSG
+ " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+ 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+ immap = (immap_t *)CFG_IMMR;
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ /*
+ * Disable PCMCIA buffers (isolate the interface)
+ * and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ /*
+ * Configure Port C pins for
+ * 5 Volts Enable and 3 Volts enable,
+ * Turn all power pins to Hi-Z
+ */
+ debug ("PCMCIA power OFF\n");
+ cfg_ports (); /* Enables switch, but all in Hi-Z */
+
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(_slot_);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ PCMCIA_PGCRX(_slot_) = reg;
+ udelay(500);
+
+ debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+ slot+'A');
+ return (0);
+}
+
+#endif /* CONFIG_PCMCIA */
diff --git a/common/cmd_bdinfo.c b/common/cmd_bdinfo.c
index 04fa4fa..256e4bc 100644
--- a/common/cmd_bdinfo.c
+++ b/common/cmd_bdinfo.c
@@ -61,11 +61,12 @@
print_num ("bootflags", bd->bi_bootflags );
#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
defined(CONFIG_405EP) || defined(CONFIG_XILINX_ML300) || \
- defined(CONFIG_440EP) || defined(CONFIG_440GR)
+ defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
+ defined(CONFIG_440SP)
print_str ("procfreq", strmhz(buf, bd->bi_procfreq));
print_str ("plb_busfreq", strmhz(buf, bd->bi_plb_busfreq));
#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || defined(CONFIG_XILINX_ML300) || \
- defined(CONFIG_440EP) || defined(CONFIG_440GR)
+ defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SPE)
print_str ("pci_busfreq", strmhz(buf, bd->bi_pci_busfreq));
#endif
#else /* ! CONFIG_405GP, CONFIG_405CR, CONFIG_405EP, CONFIG_XILINX_ML300, CONFIG_440EP CONFIG_440GR */
diff --git a/common/cmd_mem.c b/common/cmd_mem.c
index 0f4f9b7..d0fae6b 100644
--- a/common/cmd_mem.c
+++ b/common/cmd_mem.c
@@ -707,7 +707,7 @@
#if defined(CFG_MEMTEST_SCRATCH)
vu_long *dummy = (vu_long*)CFG_MEMTEST_SCRATCH;
#else
- vu_long *dummy = NULL;
+ vu_long *dummy = 0; /* yes, this is address 0x0, not NULL */
#endif
int j;
int iterations = 1;
diff --git a/common/cmd_mii.c b/common/cmd_mii.c
index 48a4e77..e659536 100644
--- a/common/cmd_mii.c
+++ b/common/cmd_mii.c
@@ -57,6 +57,11 @@
int rcode = 0;
char *devname;
+ if (argc < 2) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
#if defined(CONFIG_8xx) || defined(CONFIG_MCF52x2)
mii_init ();
#endif
@@ -112,8 +117,6 @@
miiphy_speed (devname, j),
(miiphy_duplex (devname, j) == FULL)
? "FDX" : "HDX");
- } else {
- puts ("Error reading info from the PHY\n");
}
}
} else if (op == 'r') {
@@ -498,8 +501,6 @@
miiphy_speed (devname, j),
(miiphy_duplex (devname, j) == FULL)
? "FDX" : "HDX");
- } else {
- puts ("Error reading info from the PHY\n");
}
}
} else if (op[0] == 'r') {
diff --git a/common/cmd_pcmcia.c b/common/cmd_pcmcia.c
index 8e3e84b..2eb5b26 100644
--- a/common/cmd_pcmcia.c
+++ b/common/cmd_pcmcia.c
@@ -57,75 +57,14 @@
#include <command.h>
#include <config.h>
#include <pcmcia.h>
-#if defined(CONFIG_8xx)
-#include <mpc8xx.h>
-#endif
-#if defined(CONFIG_LWMON)
-#include <i2c.h>
-#endif
-#ifdef CONFIG_PXA_PCMCIA
-#include <asm/arch/pxa-regs.h>
-#endif
-
#include <asm/io.h>
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) || \
- ((CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD))
-
-int pcmcia_on (void);
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int pcmcia_off (void);
-#endif
-
-#ifdef CONFIG_I82365
-
-extern int i82365_init (void);
-extern void i82365_exit (void);
-
-#else /* ! CONFIG_I82365 */
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot);
-#endif
-static int hardware_enable (int slot);
-static int voltage_set(int slot, int vcc, int vpp);
-
-#if (! defined(CONFIG_I82365)) && (! defined(CONFIG_PXA_PCMCIA))
-static u_int m8xx_get_graycode(u_int size);
-#endif /* !CONFIG_I82365, !CONFIG_PXA_PCMCIA */
-#if 0
-static u_int m8xx_get_speed(u_int ns, u_int is_io);
-#endif
-
/* -------------------------------------------------------------------- */
-#ifndef CONFIG_PXA_PCMCIA
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-/* look up table for pgcrx registers */
-
-static u_int *pcmcia_pgcrx[2] = {
- &((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pgcra,
- &((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pgcrb,
-};
-#define PCMCIA_PGCRX(slot) (*pcmcia_pgcrx[slot])
-
-#endif /* CONFIG_PXA_PCMCIA */
-
-#endif /* CONFIG_I82365 */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-static void print_funcid (int func);
-static void print_fixed (volatile uchar *p);
-static int identify (volatile uchar *p);
-static int check_ide_device (int slot);
-#endif /* CONFIG_IDE_8xx_PCCARD, CONFIG_PXA_PCMCIA */
-
-const char *indent = "\t ";
-
-/* -------------------------------------------------------------------- */
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+extern int pcmcia_on (void);
+extern int pcmcia_off (void);
int do_pinit (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
@@ -136,7 +75,7 @@
return 1;
}
if (strcmp(argv[1],"on") == 0) {
- rcode = pcmcia_on ();
+ rcode = pcmcia_on ();
} else if (strcmp(argv[1],"off") == 0) {
rcode = pcmcia_off ();
} else {
@@ -146,322 +85,188 @@
return rcode;
}
-#endif /* CFG_CMD_PCMCIA */
+
+U_BOOT_CMD(
+ pinit, 2, 1, do_pinit,
+ "pinit - PCMCIA sub-system\n",
+ "on - power on PCMCIA socket\n"
+ "pinit off - power off PCMCIA socket\n"
+ );
+
+#endif /* CONFIG_COMMANDS & CFG_CMD_PCMCIA */
/* -------------------------------------------------------------------- */
-#ifdef CONFIG_I82365
-int pcmcia_on (void)
-{
- u_int rc;
+#undef CHECK_IDE_DEVICE
- debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
- rc = i82365_init();
-
- if (rc == 0) {
- rc = check_ide_device(0);
- }
-
- return (rc);
-}
-#else
-
-#ifndef CONFIG_PXA_PCMCIA
-
-#ifdef CONFIG_HMI10
-# define HMI10_FRAM_TIMING (PCMCIA_SHT(2) | PCMCIA_SST(2) | PCMCIA_SL(4))
-#endif
-#if defined(CONFIG_LWMON) || defined(CONFIG_NSCU)
-# define CFG_PCMCIA_TIMING (PCMCIA_SHT(9) | PCMCIA_SST(3) | PCMCIA_SL(12))
-#else
-# define CFG_PCMCIA_TIMING (PCMCIA_SHT(2) | PCMCIA_SST(4) | PCMCIA_SL(9))
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CHECK_IDE_DEVICE
#endif
-int pcmcia_on (void)
-{
- int i;
- u_long reg, base;
- pcmcia_win_t *win;
- u_int slotbit;
- u_int rc, slot;
-
- debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
- /* intialize the fixed memory windows */
- win = (pcmcia_win_t *)(&((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pbr0);
- base = CFG_PCMCIA_MEM_ADDR;
-
- if((reg = m8xx_get_graycode(CFG_PCMCIA_MEM_SIZE)) == -1) {
- printf ("Cannot set window size to 0x%08x\n",
- CFG_PCMCIA_MEM_SIZE);
- return (1);
- }
-
- slotbit = PCMCIA_SLOT_x;
- for (i=0; i<PCMCIA_MEM_WIN_NO; ++i) {
- win->br = base;
-
-#if (PCMCIA_SOCKETS_NO == 2)
- if (i == 4) /* Another slot starting from win 4 */
- slotbit = (slotbit ? PCMCIA_PSLOT_A : PCMCIA_PSLOT_B);
-#endif
- switch (i) {
-#ifdef CONFIG_IDE_8xx_PCCARD
- case 4:
-#ifdef CONFIG_HMI10
- { /* map FRAM area */
- win->or = ( PCMCIA_BSIZE_256K
- | PCMCIA_PPS_8
- | PCMCIA_PRS_ATTR
- | slotbit
- | PCMCIA_PV
- | HMI10_FRAM_TIMING );
- break;
- }
-#endif
- case 0: { /* map attribute memory */
- win->or = ( PCMCIA_BSIZE_64M
- | PCMCIA_PPS_8
- | PCMCIA_PRS_ATTR
- | slotbit
- | PCMCIA_PV
- | CFG_PCMCIA_TIMING );
- break;
- }
- case 5:
- case 1: { /* map I/O window for data reg */
- win->or = ( PCMCIA_BSIZE_1K
- | PCMCIA_PPS_16
- | PCMCIA_PRS_IO
- | slotbit
- | PCMCIA_PV
- | CFG_PCMCIA_TIMING );
- break;
- }
- case 6:
- case 2: { /* map I/O window for cmd/ctrl reg block */
- win->or = ( PCMCIA_BSIZE_1K
- | PCMCIA_PPS_8
- | PCMCIA_PRS_IO
- | slotbit
- | PCMCIA_PV
- | CFG_PCMCIA_TIMING );
- break;
- }
-#endif /* CONFIG_IDE_8xx_PCCARD */
-#ifdef CONFIG_HMI10
- case 3: { /* map I/O window for 4xUART data/ctrl */
- win->br += 0x40000;
- win->or = ( PCMCIA_BSIZE_256K
- | PCMCIA_PPS_8
- | PCMCIA_PRS_IO
- | slotbit
- | PCMCIA_PV
- | CFG_PCMCIA_TIMING );
- break;
- }
-#endif /* CONFIG_HMI10 */
- default: /* set to not valid */
- win->or = 0;
- break;
- }
-
- debug ("MemWin %d: PBR 0x%08lX POR %08lX\n",
- i, win->br, win->or);
- base += CFG_PCMCIA_MEM_SIZE;
- ++win;
- }
-
- for (i=0, rc=0, slot=_slot_; i<PCMCIA_SOCKETS_NO; i++, slot = !slot) {
- /* turn off voltage */
- if ((rc = voltage_set(slot, 0, 0)))
- continue;
-
- /* Enable external hardware */
- if ((rc = hardware_enable(slot)))
- continue;
-
-#ifdef CONFIG_IDE_8xx_PCCARD
- if ((rc = check_ide_device(i)))
- continue;
-#endif
- }
- return (rc);
-}
-
-#endif /* CONFIG_PXA_PCMCIA */
-
-#endif /* CONFIG_I82365 */
-
-#ifdef CONFIG_PXA_PCMCIA
-
-static int hardware_enable (int slot)
-{
- return 0; /* No hardware to enable */
-}
-
-static int hardware_disable(int slot)
-{
- return 0; /* No hardware to disable */
-}
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- return 0;
-}
-
-void msWait(unsigned msVal)
-{
- udelay(msVal*1000);
-}
-
-int pcmcia_on (void)
-{
- unsigned int reg_arr[] = {
- 0x48000028, CFG_MCMEM0_VAL,
- 0x4800002c, CFG_MCMEM1_VAL,
- 0x48000030, CFG_MCATT0_VAL,
- 0x48000034, CFG_MCATT1_VAL,
- 0x48000038, CFG_MCIO0_VAL,
- 0x4800003c, CFG_MCIO1_VAL,
-
- 0, 0
- };
- int i, rc;
-
-#ifdef CONFIG_EXADRON1
- int cardDetect;
- volatile unsigned int *v_pBCRReg =
- (volatile unsigned int *) 0x08000000;
+#if defined(CONFIG_PXA_PCMCIA)
+#define CHECK_IDE_DEVICE
#endif
- debug ("%s\n", __FUNCTION__);
+#ifdef CHECK_IDE_DEVICE
- i = 0;
- while (reg_arr[i])
- *((volatile unsigned int *) reg_arr[i++]) |= reg_arr[i++];
- udelay (1000);
-
- debug ("%s: programmed mem controller \n", __FUNCTION__);
-
-#ifdef CONFIG_EXADRON1
-
-/*define useful BCR masks */
-#define BCR_CF_INIT_VAL 0x00007230
-#define BCR_CF_PWRON_BUSOFF_RESETOFF_VAL 0x00007231
-#define BCR_CF_PWRON_BUSOFF_RESETON_VAL 0x00007233
-#define BCR_CF_PWRON_BUSON_RESETON_VAL 0x00007213
-#define BCR_CF_PWRON_BUSON_RESETOFF_VAL 0x00007211
-
- /* we see from the GPIO bit if the card is present */
- cardDetect = !(GPLR0 & GPIO_bit (14));
-
- if (cardDetect) {
- printf ("No PCMCIA card found!\n");
- }
-
- /* reset the card via the BCR line */
- *v_pBCRReg = (unsigned) BCR_CF_INIT_VAL;
- msWait (500);
-
- *v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSOFF_RESETOFF_VAL;
- msWait (500);
-
- *v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSOFF_RESETON_VAL;
- msWait (500);
-
- *v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSON_RESETON_VAL;
- msWait (500);
-
- *v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSON_RESETOFF_VAL;
- msWait (1500);
-
- /* enable address bus */
- GPCR1 = 0x01;
- /* and the first CF slot */
- MECR = 0x00000002;
-
-#endif /* EXADRON 1 */
-
- rc = check_ide_device (0); /* use just slot 0 */
-
- return rc;
-}
-
-#endif /* CONFIG_PXA_PCMCIA */
-
-/* -------------------------------------------------------------------- */
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-
-#ifdef CONFIG_I82365
-static int pcmcia_off (void)
-{
- printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
- i82365_exit();
-
- return 0;
-}
-#else
-
-#ifndef CONFIG_PXA_PCMCIA
-
-static int pcmcia_off (void)
-{
- int i;
- pcmcia_win_t *win;
-
- printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
- /* clear interrupt state, and disable interrupts */
- ((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pscr = PCMCIA_MASK(_slot_);
- ((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /* turn off interrupt and disable CxOE */
- PCMCIA_PGCRX(_slot_) = __MY_PCMCIA_GCRX_CXOE;
-
- /* turn off memory windows */
- win = (pcmcia_win_t *)(&((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pbr0);
-
- for (i=0; i<PCMCIA_MEM_WIN_NO; ++i) {
- /* disable memory window */
- win->or = 0;
- ++win;
- }
-
- /* turn off voltage */
- voltage_set(_slot_, 0, 0);
-
- /* disable external hardware */
- printf ("Shutdown and Poweroff " PCMCIA_SLOT_MSG "\n");
- hardware_disable(_slot_);
- return 0;
-}
-
-#endif /* CONFIG_PXA_PCMCIA */
-
-#endif /* CONFIG_I82365 */
-
-#ifdef CONFIG_PXA_PCMCIA
-static int pcmcia_off (void)
-{
- return 0;
-}
-#endif
-
-#endif /* CFG_CMD_PCMCIA */
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
+int ide_devices_found;
+static uchar *known_cards[] = {
+ (uchar *)"ARGOSY PnPIDE D5",
+ NULL
+};
#define MAX_TUPEL_SZ 512
#define MAX_FEATURES 4
-int ide_devices_found;
-static int check_ide_device (int slot)
+#define MAX_IDENT_CHARS 64
+#define MAX_IDENT_FIELDS 4
+
+#define indent "\t "
+
+static void print_funcid (int func)
+{
+ puts (indent);
+ switch (func) {
+ case CISTPL_FUNCID_MULTI:
+ puts (" Multi-Function");
+ break;
+ case CISTPL_FUNCID_MEMORY:
+ puts (" Memory");
+ break;
+ case CISTPL_FUNCID_SERIAL:
+ puts (" Serial Port");
+ break;
+ case CISTPL_FUNCID_PARALLEL:
+ puts (" Parallel Port");
+ break;
+ case CISTPL_FUNCID_FIXED:
+ puts (" Fixed Disk");
+ break;
+ case CISTPL_FUNCID_VIDEO:
+ puts (" Video Adapter");
+ break;
+ case CISTPL_FUNCID_NETWORK:
+ puts (" Network Adapter");
+ break;
+ case CISTPL_FUNCID_AIMS:
+ puts (" AIMS Card");
+ break;
+ case CISTPL_FUNCID_SCSI:
+ puts (" SCSI Adapter");
+ break;
+ default:
+ puts (" Unknown");
+ break;
+ }
+ puts (" Card\n");
+}
+
+static void print_fixed (volatile uchar *p)
+{
+ if (p == NULL)
+ return;
+
+ puts(indent);
+
+ switch (*p) {
+ case CISTPL_FUNCE_IDE_IFACE:
+ { uchar iface = *(p+2);
+
+ puts ((iface == CISTPL_IDE_INTERFACE) ? " IDE" : " unknown");
+ puts (" interface ");
+ break;
+ }
+ case CISTPL_FUNCE_IDE_MASTER:
+ case CISTPL_FUNCE_IDE_SLAVE:
+ { uchar f1 = *(p+2);
+ uchar f2 = *(p+4);
+
+ puts ((f1 & CISTPL_IDE_SILICON) ? " [silicon]" : " [rotating]");
+
+ if (f1 & CISTPL_IDE_UNIQUE)
+ puts (" [unique]");
+
+ puts ((f1 & CISTPL_IDE_DUAL) ? " [dual]" : " [single]");
+
+ if (f2 & CISTPL_IDE_HAS_SLEEP)
+ puts (" [sleep]");
+
+ if (f2 & CISTPL_IDE_HAS_STANDBY)
+ puts (" [standby]");
+
+ if (f2 & CISTPL_IDE_HAS_IDLE)
+ puts (" [idle]");
+
+ if (f2 & CISTPL_IDE_LOW_POWER)
+ puts (" [low power]");
+
+ if (f2 & CISTPL_IDE_REG_INHIBIT)
+ puts (" [reg inhibit]");
+
+ if (f2 & CISTPL_IDE_HAS_INDEX)
+ puts (" [index]");
+
+ if (f2 & CISTPL_IDE_IOIS16)
+ puts (" [IOis16]");
+
+ break;
+ }
+ }
+ putc ('\n');
+}
+
+static int identify (volatile uchar *p)
+{
+ uchar id_str[MAX_IDENT_CHARS];
+ uchar data;
+ uchar *t;
+ uchar **card;
+ int i, done;
+
+ if (p == NULL)
+ return (0); /* Don't know */
+
+ t = id_str;
+ done =0;
+
+ for (i=0; i<=4 && !done; ++i, p+=2) {
+ while ((data = *p) != '\0') {
+ if (data == 0xFF) {
+ done = 1;
+ break;
+ }
+ *t++ = data;
+ if (t == &id_str[MAX_IDENT_CHARS-1]) {
+ done = 1;
+ break;
+ }
+ p += 2;
+ }
+ if (!done)
+ *t++ = ' ';
+ }
+ *t = '\0';
+ while (--t > id_str) {
+ if (*t == ' ')
+ *t = '\0';
+ else
+ break;
+ }
+ puts ((char *)id_str);
+ putc ('\n');
+
+ for (card=known_cards; *card; ++card) {
+ debug ("## Compare against \"%s\"\n", *card);
+ if (strcmp((char *)*card, (char *)id_str) == 0) { /* found! */
+ debug ("## CARD FOUND ##\n");
+ return (1);
+ }
+ }
+
+ return (0); /* don't know */
+}
+
+int check_ide_device (int slot)
{
volatile uchar *ident = NULL;
volatile uchar *feature_p[MAX_FEATURES];
@@ -556,2933 +361,5 @@
#endif
return (0);
}
-#endif /* CONFIG_IDE_8xx_PCCARD */
-/* -------------------------------------------------------------------- */
-
-
-/* -------------------------------------------------------------------- */
-/* board specific stuff: */
-/* voltage_set(), hardware_enable() and hardware_disable() */
-/* -------------------------------------------------------------------- */
-
-/* -------------------------------------------------------------------- */
-/* RPX Boards from Embedded Planet */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE)
-
-/* The RPX boards seems to have it's bus monitor timeout set to 6*8 clocks.
- * SYPCR is write once only, therefore must the slowest memory be faster
- * than the bus monitor or we will get a machine check due to the bus timeout.
- */
-
-#define PCMCIA_BOARD_MSG "RPX CLASSIC or RPX LITE"
-
-#undef PCMCIA_BMT_LIMIT
-#define PCMCIA_BMT_LIMIT (6*8)
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- u_long reg = 0;
-
- switch(vcc) {
- case 0: break;
- case 33: reg |= BCSR1_PCVCTL4; break;
- case 50: reg |= BCSR1_PCVCTL5; break;
- default: return 1;
- }
-
- switch(vpp) {
- case 0: break;
- case 33:
- case 50:
- if(vcc == vpp)
- reg |= BCSR1_PCVCTL6;
- else
- return 1;
- break;
- case 120:
- reg |= BCSR1_PCVCTL7;
- default: return 1;
- }
-
- if(vcc == 120)
- return 1;
-
- /* first, turn off all power */
-
- *((uint *)RPX_CSR_ADDR) &= ~(BCSR1_PCVCTL4 | BCSR1_PCVCTL5
- | BCSR1_PCVCTL6 | BCSR1_PCVCTL7);
-
- /* enable new powersettings */
-
- *((uint *)RPX_CSR_ADDR) |= reg;
-
- return 0;
-}
-
-#define socket_get(_slot_) PCMCIA_SOCKET_KEY_5V
-static int hardware_enable (int slot)
-{
- return 0; /* No hardware to enable */
-}
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- return 0; /* No hardware to disable */
-}
-#endif /* CFG_CMD_PCMCIA */
-#endif /* CONFIG_RPXCLASSIC */
-
-/* -------------------------------------------------------------------- */
-/* (F)ADS Boards from Motorola */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ADS) || defined(CONFIG_FADS)
-
-#ifdef CONFIG_ADS
-#define PCMCIA_BOARD_MSG "ADS"
-#define PCMCIA_GLITCHY_CD /* My ADS board needs this */
-#else
-#define PCMCIA_BOARD_MSG "FADS"
-#endif
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- u_long reg = 0;
-
- switch(vpp) {
- case 0: reg = 0; break;
- case 50: reg = 1; break;
- case 120: reg = 2; break;
- default: return 1;
- }
-
- switch(vcc) {
- case 0: reg = 0; break;
-#ifdef CONFIG_ADS
- case 50: reg = BCSR1_PCCVCCON; break;
-#endif
-#ifdef CONFIG_FADS
- case 33: reg = BCSR1_PCCVCC0 | BCSR1_PCCVCC1; break;
- case 50: reg = BCSR1_PCCVCC1; break;
-#endif
- default: return 1;
- }
-
- /* first, turn off all power */
-
-#ifdef CONFIG_ADS
- *((uint *)BCSR1) |= BCSR1_PCCVCCON;
-#endif
-#ifdef CONFIG_FADS
- *((uint *)BCSR1) &= ~(BCSR1_PCCVCC0 | BCSR1_PCCVCC1);
-#endif
- *((uint *)BCSR1) &= ~BCSR1_PCCVPP_MASK;
-
- /* enable new powersettings */
-
-#ifdef CONFIG_ADS
- *((uint *)BCSR1) &= ~reg;
-#endif
-#ifdef CONFIG_FADS
- *((uint *)BCSR1) |= reg;
-#endif
-
- *((uint *)BCSR1) |= reg << 20;
-
- return 0;
-}
-
-#define socket_get(_slot_) PCMCIA_SOCKET_KEY_5V
-
-static int hardware_enable(int slot)
-{
- *((uint *)BCSR1) &= ~BCSR1_PCCEN;
- return 0;
-}
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- *((uint *)BCSR1) &= ~BCSR1_PCCEN;
- return 0;
-}
-#endif /* CFG_CMD_PCMCIA */
-
-#endif /* (F)ADS */
-
-/* -------------------------------------------------------------------- */
-/* TQM8xxL Boards by TQ Components */
-/* SC8xx Boards by SinoVee Microsystems */
-/* -------------------------------------------------------------------- */
-
-#if (defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx)) \
- && !defined(CONFIG_VIRTLAB2)
-
-#if defined(CONFIG_TQM8xxL)
-#define PCMCIA_BOARD_MSG "TQM8xxL"
-#endif
-#if defined(CONFIG_SVM_SC8xx)
-#define PCMCIA_BOARD_MSG "SC8xx"
-#endif
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(slot);
- pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
-#ifndef CONFIG_HMI10
-#ifndef CONFIG_NSCU
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable
- */
- immap->im_ioport.iop_pcpar &= ~(0x0002 | 0x0004);
- immap->im_ioport.iop_pcso &= ~(0x0002 | 0x0004);
- /* remove all power */
-
- immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
-#endif
-#else /* CONFIG_HMI10 */
- /*
- * Configure Port B pins for
- * 5 Volts Enable and 3 Volts enable
- */
- immap->im_cpm.cp_pbpar &= ~(0x00000300);
-
- /* remove all power */
- immap->im_cpm.cp_pbdat |= 0x00000300;
-#endif /* CONFIG_HMI10 */
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-#ifndef CONFIG_HMI10
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-#else
- if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
-#endif /* CONFIG_HMI10 */
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-#ifndef CONFIG_NSCU
- if ((reg & mask) == mask) {
-#ifndef CONFIG_HMI10
- immap->im_ioport.iop_pcdat |= 0x0004;
-#else
- immap->im_cpm.cp_pbdat &= ~(0x0000100);
-#endif /* CONFIG_HMI10 */
- puts (" 5.0V card found: ");
- } else {
-#ifndef CONFIG_HMI10
- immap->im_ioport.iop_pcdat |= 0x0002;
-#else
- immap->im_cpm.cp_pbdat &= ~(0x0000200);
-#endif /* CONFIG_HMI10 */
- puts (" 3.3V card found: ");
- }
-#ifndef CONFIG_HMI10
- immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004);
-#else
- immap->im_cpm.cp_pbdir |= 0x00000300;
-#endif /* CONFIG_HMI10 */
-#else
- if ((reg & mask) == mask) {
- puts (" 5.0V card found: ");
- } else {
- puts (" 3.3V card found: ");
- }
-#endif
-#if 0
- /* VCC switch error flag, PCMCIA slot INPACK_ pin */
- cp->cp_pbdir &= ~(0x0020 | 0x0010);
- cp->cp_pbpar &= ~(0x0020 | 0x0010);
- udelay(500000);
-#endif
- udelay(1000);
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
-#else
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
-#ifndef CONFIG_HMI10
-#ifndef CONFIG_NSCU
- /* remove all power */
- immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
-#endif
-#else /* CONFIG_HMI10 */
- immap->im_cpm.cp_pbdat |= 0x00000300;
-#endif /* CONFIG_HMI10 */
-
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-#ifdef CONFIG_NSCU
-static int voltage_set(int slot, int vcc, int vpp)
-{
- return 0;
-}
-#else
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#else
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
-#ifndef CONFIG_HMI10
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn off all power
- */
- debug ("PCMCIA power OFF\n");
- immap->im_ioport.iop_pcpar &= ~(0x0002 | 0x0004);
- immap->im_ioport.iop_pcso &= ~(0x0002 | 0x0004);
- immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
-
- reg = 0;
- switch(vcc) {
- case 0: break;
- case 33: reg |= 0x0002; break;
- case 50: reg |= 0x0004; break;
- default: goto done;
- }
-#else /* CONFIG_HMI10 */
- /*
- * Configure Port B pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn off all power
- */
- debug ("PCMCIA power OFF\n");
- immap->im_cpm.cp_pbpar &= ~(0x00000300);
- /* remove all power */
-
- immap->im_cpm.cp_pbdat |= 0x00000300;
-
- reg = 0;
- switch(vcc) {
- case 0: break;
- case 33: reg |= 0x00000200; break;
- case 50: reg |= 0x00000100; break;
- default: goto done;
-}
-#endif /* CONFIG_HMI10 */
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-#ifndef CONFIG_HMI10
- immap->im_ioport.iop_pcdat |= reg;
- immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004);
-#else
- immap->im_cpm.cp_pbdat &= !reg;
- immap->im_cpm.cp_pbdir |= 0x00000300;
-#endif /* CONFIG_HMI10 */
- if (reg) {
-#ifndef CONFIG_HMI10
- debug ("PCMCIA powered at %sV\n",
- (reg&0x0004) ? "5.0" : "3.3");
-#else
- debug ("PCMCIA powered at %sV\n",
- (reg&0x00000200) ? "5.0" : "3.3");
-#endif /* CONFIG_HMI10 */
- } else {
- debug ("PCMCIA powered down\n");
- }
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
-#ifndef NSCU_OE_INV
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
-#else
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-#endif
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-#endif
-
-#endif /* TQM8xxL */
-
-/* -------------------------------------------------------------------- */
-/* Virtlab2 Board by TQ Components */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_VIRTLAB2)
-#define PCMCIA_BOARD_MSG "Virtlab2"
-
-static int hardware_enable(int slot)
-{
- volatile pcmconf8xx_t *pcmp =
- (pcmconf8xx_t *)&(((immap_t *)CFG_IMMR)->im_pcmcia);
- volatile unsigned char *powerctl =
- (volatile unsigned char *)PCMCIA_CTRL;
- volatile sysconf8xx_t *sysp =
- (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- unsigned int reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(slot);
- pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- /* remove all power */
- *powerctl = 0;
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n", __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-
- if ((reg & mask) == mask) {
- *powerctl = 2; /* Enable 5V Vccout */
- puts (" 5.0V card found: ");
- } else {
- *powerctl = 1; /* Enable 3.3 V Vccout */
- puts (" 3.3V card found: ");
- }
-
- udelay(1000);
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
-
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile unsigned char *powerctl =
- (volatile unsigned char *)PCMCIA_CTRL;
- unsigned long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- /* remove all power */
- *powerctl = 0;
-
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-#ifdef DEBUG
- volatile pcmconf8xx_t *pcmp =
- (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-#endif
- volatile unsigned char *powerctl =
- (volatile unsigned char *)PCMCIA_CTRL;
- unsigned long reg;
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
-
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- /*
- * Configure pins for 5 Volts Enable and 3 Volts enable,
- * Turn off all power.
- */
- debug ("PCMCIA power OFF\n");
- reg = 0;
- switch(vcc) {
- case 0: break;
- case 33: reg = 0x0001; break;
- case 50: reg = 0x0002; break;
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n", pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- *powerctl = reg;
-
- if (reg) {
- debug ("PCMCIA powered at %sV\n", (reg&0x0004) ? "5.0" : "3.3");
- } else {
- debug ("PCMCIA powered down\n");
- }
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
-
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", slot+'A');
- return (0);
-}
-#endif /* CONFIG_VIRTLAB2 */
-
-/* -------------------------------------------------------------------- */
-/* LWMON Board */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_LWMON)
-
-#define PCMCIA_BOARD_MSG "LWMON"
-
-/* #define's for MAX1604 Power Switch */
-#define MAX1604_OP_SUS 0x80
-#define MAX1604_VCCBON 0x40
-#define MAX1604_VCC_35 0x20
-#define MAX1604_VCCBHIZ 0x10
-#define MAX1604_VPPBON 0x08
-#define MAX1604_VPPBPBPGM 0x04
-#define MAX1604_VPPBHIZ 0x02
-/* reserved 0x01 */
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
- uchar val;
-
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- /* Switch on PCMCIA port in PIC register 0x60 */
- reg = pic_read (0x60);
- debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
- reg &= ~0x10;
- /* reg |= 0x08; Vpp not needed */
- pic_write (0x60, reg);
-#ifdef DEBUG
- reg = pic_read (0x60);
- printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-#endif
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
- if ((reg & mask) == mask) {
- val = 0; /* VCCB3/5 = 0 ==> use Vx = 5.0 V */
- puts (" 5.0V card found: ");
- } else {
- val = MAX1604_VCC_35; /* VCCB3/5 = 1 ==> use Vy = 3.3 V */
- puts (" 3.3V card found: ");
- }
-
- /* switch VCC on */
- val |= MAX1604_OP_SUS | MAX1604_VCCBON;
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
- i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
- udelay(500000);
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- uchar val;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* remove all power, put output in high impedance state */
- val = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
- i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- /* Switch off PCMCIA port in PIC register 0x60 */
- reg = pic_read (0x60);
- debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
- reg |= 0x10;
- reg &= ~0x08;
- pic_write (0x60, reg);
-#ifdef DEBUG
- reg = pic_read (0x60);
- printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-#endif
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- uchar val;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Turn off all power (switch to high impedance)
- */
- debug ("PCMCIA power OFF\n");
- val = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
- i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
- val = 0;
- switch(vcc) {
- case 0: break;
- case 33: val = MAX1604_VCC_35; break;
- case 50: break;
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
- if (val) {
- debug ("PCMCIA powered at %sV\n",
- (val & MAX1604_VCC_35) ? "3.3" : "5.0");
- } else {
- debug ("PCMCIA powered down\n");
- }
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-#endif /* LWMON */
-
-/* -------------------------------------------------------------------- */
-/* GTH board by Corelatus AB */
-/* -------------------------------------------------------------------- */
-#if defined(CONFIG_GTH)
-
-#define PCMCIA_BOARD_MSG "GTH COMPACT FLASH"
-
-static int voltage_set (int slot, int vcc, int vpp)
-{ /* Do nothing */
- return 0;
-}
-
-static int hardware_enable (int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: GTH Slot %c\n", 'A' + slot);
-
- immap = (immap_t *) CFG_IMMR;
- sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
- udelay (500);
-
- /*
- * Make sure there is a card in the slot,
- * then configure the interface.
- */
- udelay (10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__, __FUNCTION__,
- &(pcmp->pcmc_pipr), pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & 0x98000000) {
- printf (" No Card found\n");
- return (1);
- }
-
- mask = PCMCIA_VS1 (slot) | PCMCIA_VS2 (slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
- (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX (_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
-
- udelay (250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return 0;
-}
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- return 0; /* No hardware to disable */
-}
-#endif /* CFG_CMD_PCMCIA */
-#endif /* CONFIG_GTH */
-
-/* -------------------------------------------------------------------- */
-/* ICU862 Boards by Cambridge Broadband Ltd. */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ICU862)
-
-#define PCMCIA_BOARD_MSG "ICU862"
-
-static void cfg_port_B (void);
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, pipr, mask;
- int i;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /* Configure Port B for TPS2205 PC-Card Power-Interface Switch */
- cfg_port_B ();
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- pipr = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- pipr,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-
- reg = cp->cp_pbdat;
- if ((pipr & mask) == mask) {
- reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
- TPS2205_VCC3); /* 3V off */
- reg &= ~(TPS2205_VCC5); /* 5V on */
- puts (" 5.0V card found: ");
- } else {
- reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
- TPS2205_VCC5); /* 5V off */
- reg &= ~(TPS2205_VCC3); /* 3V on */
- puts (" 3.3V card found: ");
- }
-
- debug ("\nPB DAT: %08x -> 3.3V %s 5.0V %s VPP_PGM %s VPP_VCC %s\n",
- reg,
- (reg & TPS2205_VCC3) ? "off" : "on",
- (reg & TPS2205_VCC5) ? "off" : "on",
- (reg & TPS2205_VPP_PGM) ? "off" : "on",
- (reg & TPS2205_VPP_VCC) ? "off" : "on" );
-
- cp->cp_pbdat = reg;
-
- /* Wait 500 ms; use this to check for over-current */
- for (i=0; i<5000; ++i) {
- if ((cp->cp_pbdat & TPS2205_OC) == 0) {
- printf (" *** Overcurrent - Safety shutdown ***\n");
- cp->cp_pbdat &= ~(TPS2205_SHDN);
- return (1);
- }
- udelay (100);
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* Shut down */
- cp->cp_pbdat &= ~(TPS2205_SHDN);
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn all power pins to Hi-Z
- */
- debug ("PCMCIA power OFF\n");
- cfg_port_B (); /* Enables switch, but all in Hi-Z */
-
- reg = cp->cp_pbdat;
-
- switch(vcc) {
- case 0: break; /* Switch off */
- case 33: reg &= ~TPS2205_VCC3; break; /* Switch on 3.3V */
- case 50: reg &= ~TPS2205_VCC5; break; /* Switch on 5.0V */
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- cp->cp_pbdat = reg;
-
-#ifdef DEBUG
- {
- char *s;
-
- if ((reg & TPS2205_VCC3) == 0) {
- s = "at 3.3V";
- } else if ((reg & TPS2205_VCC5) == 0) {
- s = "at 5.0V";
- } else {
- s = "down";
- }
- printf ("PCMCIA powered %s\n", s);
- }
-#endif
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-static void cfg_port_B (void)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- uint reg;
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure Port B for TPS2205 PC-Card Power-Interface Switch
- *
- * Switch off all voltages, assert shutdown
- */
- reg = cp->cp_pbdat;
- reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC | /* VAVPP => Hi-Z */
- TPS2205_VCC3 | TPS2205_VCC5 | /* VAVCC => Hi-Z */
- TPS2205_SHDN); /* enable switch */
- cp->cp_pbdat = reg;
-
- cp->cp_pbpar &= ~(TPS2205_INPUTS | TPS2205_OUTPUTS);
-
- reg = cp->cp_pbdir & ~(TPS2205_INPUTS);
- cp->cp_pbdir = reg | TPS2205_OUTPUTS;
-
- debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
- cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
-}
-
-#endif /* ICU862 */
-
-
-/* -------------------------------------------------------------------- */
-/* C2MON Boards by TTTech Computertechnik AG */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_C2MON)
-
-#define PCMCIA_BOARD_MSG "C2MON"
-
-static void cfg_ports (void);
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, pipr, mask;
- ushort sreg;
- int i;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
- cfg_ports ();
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- pipr = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- pipr,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-
- sreg = immap->im_ioport.iop_pcdat;
- if ((pipr & mask) == mask) {
- sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1 | /* VAVPP => Hi-Z */
- TPS2211_VCCD1); /* 5V on */
- sreg &= ~(TPS2211_VCCD0); /* 3V off */
- puts (" 5.0V card found: ");
- } else {
- sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1 | /* VAVPP => Hi-Z */
- TPS2211_VCCD0); /* 3V on */
- sreg &= ~(TPS2211_VCCD1); /* 5V off */
- puts (" 3.3V card found: ");
- }
-
- debug ("\nPC DAT: %04x -> 3.3V %s 5.0V %s\n",
- sreg,
- ( (sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) ? "on" : "off",
- (!(sreg & TPS2211_VCCD0) && (sreg & TPS2211_VCCD1)) ? "on" : "off"
- );
-
- immap->im_ioport.iop_pcdat = sreg;
-
- /* Wait 500 ms; use this to check for over-current */
- for (i=0; i<5000; ++i) {
- if ((cp->cp_pbdat & TPS2211_OC) == 0) {
- printf (" *** Overcurrent - Safety shutdown ***\n");
- immap->im_ioport.iop_pcdat &= ~(TPS2211_VCCD0|TPS2211_VCCD1);
- return (1);
- }
- udelay (100);
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- /* ALl voltages off / Hi-Z */
- immap->im_ioport.iop_pcdat |= (TPS2211_VPPD0 | TPS2211_VPPD1 |
- TPS2211_VCCD0 | TPS2211_VCCD1 );
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- ushort sreg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn all power pins to Hi-Z
- */
- debug ("PCMCIA power OFF\n");
- cfg_ports (); /* Enables switch, but all in Hi-Z */
-
- sreg = immap->im_ioport.iop_pcdat;
- sreg |= TPS2211_VPPD0 | TPS2211_VPPD1; /* VAVPP always Hi-Z */
-
- switch(vcc) {
- case 0: break; /* Switch off */
- case 33: sreg |= TPS2211_VCCD0; /* Switch on 3.3V */
- sreg &= ~TPS2211_VCCD1;
- break;
- case 50: sreg &= ~TPS2211_VCCD0; /* Switch on 5.0V */
- sreg |= TPS2211_VCCD1;
- break;
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- immap->im_ioport.iop_pcdat = sreg;
-
-#ifdef DEBUG
- {
- char *s;
-
- if ((sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) {
- s = "at 3.3V";
- } else if (!(sreg & TPS2211_VCCD0) && (sreg & TPS2211_VCCD1)) {
- s = "at 5.0V";
- } else {
- s = "down";
- }
- printf ("PCMCIA powered %s\n", s);
- }
-#endif
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-static void cfg_ports (void)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- ushort sreg;
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure Port C for TPS2211 PC-Card Power-Interface Switch
- *
- * Switch off all voltages, assert shutdown
- */
- sreg = immap->im_ioport.iop_pcdat;
- sreg |= (TPS2211_VPPD0 | TPS2211_VPPD1); /* VAVPP => Hi-Z */
- sreg &= ~(TPS2211_VCCD0 | TPS2211_VCCD1); /* 3V and 5V off */
- immap->im_ioport.iop_pcdat = sreg;
-
- immap->im_ioport.iop_pcpar &= ~(TPS2211_OUTPUTS);
- immap->im_ioport.iop_pcdir |= TPS2211_OUTPUTS;
-
- debug ("Set Port C: PAR: %04x DIR: %04x DAT: %04x\n",
- immap->im_ioport.iop_pcpar,
- immap->im_ioport.iop_pcdir,
- immap->im_ioport.iop_pcdat);
-
- /*
- * Configure Port B for TPS2211 PC-Card Power-Interface Switch
- *
- * Over-Current Input only
- */
- cp->cp_pbpar &= ~(TPS2211_INPUTS);
- cp->cp_pbdir &= ~(TPS2211_INPUTS);
-
- debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
- cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
-}
-
-#endif /* C2MON */
-
-/* -------------------------------------------------------------------- */
-/* MBX board from Morotola */
-/* -------------------------------------------------------------------- */
-
-#if defined( CONFIG_MBX )
-#include <../board/mbx8xx/csr.h>
-
-/* A lot of this has been taken from the RPX code in this file it works from me.
- I have added the voltage selection for the MBX board. */
-
-/* MBX voltage bit in control register #2 */
-#define CR2_VPP12 ((uchar)0x10)
-#define CR2_VPPVDD ((uchar)0x20)
-#define CR2_VDD5 ((uchar)0x40)
-#define CR2_VDD3 ((uchar)0x80)
-
-#define PCMCIA_BOARD_MSG "MBX860"
-
-static int voltage_set (int slot, int vcc, int vpp)
-{
- uchar reg = 0;
-
- debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
-
- switch (vcc) {
- case 0:
- break;
- case 33:
- reg |= CR2_VDD3;
- break;
- case 50:
- reg |= CR2_VDD5;
- break;
- default:
- return 1;
- }
-
- switch (vpp) {
- case 0:
- break;
- case 33:
- case 50:
- if (vcc == vpp) {
- reg |= CR2_VPPVDD;
- } else {
- return 1;
- }
- break;
- case 120:
- reg |= CR2_VPP12;
- break;
- default:
- return 1;
- }
-
- /* first, turn off all power */
- MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
-
- /* enable new powersettings */
- MBX_CSR2 |= reg;
- debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
-
- return (0);
-}
-
-static int hardware_enable (int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
- 'A' + slot);
-
- udelay (10000);
-
- immap = (immap_t *) CFG_IMMR;
- sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
- udelay (500);
-
- /* remove all power */
- voltage_set (slot, 0, 0);
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-#ifndef CONFIG_HMI10
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-#else
- if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
-#endif /* CONFIG_HMI10 */
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
- (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
- (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
-
- if ((reg & mask) == mask) {
- voltage_set (_slot_, 50, 0);
- printf (" 5.0V card found: ");
- } else {
- voltage_set (_slot_, 33, 0);
- printf (" 3.3V card found: ");
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX (_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
-
- udelay (250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable (int slot)
-{
- return 0; /* No hardware to disable */
-}
-#endif /* CFG_CMD_PCMCIA */
-#endif /* CONFIG_MBX */
-/* -------------------------------------------------------------------- */
-/* R360MPI Board */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_R360MPI)
-
-#define PCMCIA_BOARD_MSG "R360MPI"
-
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Ports A, B & C pins for
- * 5 Volts Enable and 3 Volts enable
- */
- immap->im_ioport.iop_pcpar &= ~(0x0400);
- immap->im_ioport.iop_pcso &= ~(0x0400);/*
- immap->im_ioport.iop_pcdir |= 0x0400;*/
-
- immap->im_ioport.iop_papar &= ~(0x0200);/*
- immap->im_ioport.iop_padir |= 0x0200;*/
-#if 0
- immap->im_ioport.iop_pbpar &= ~(0xC000);
- immap->im_ioport.iop_pbdir &= ~(0xC000);
-#endif
- /* remove all power */
-
- immap->im_ioport.iop_pcdat |= 0x0400;
- immap->im_ioport.iop_padat |= 0x0200;
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
- if ((reg & mask) == mask) {
- immap->im_ioport.iop_pcdat &= ~(0x4000);
- puts (" 5.0V card found: ");
- } else {
- immap->im_ioport.iop_padat &= ~(0x0002);
- puts (" 3.3V card found: ");
- }
- immap->im_ioport.iop_pcdir |= 0x0400;
- immap->im_ioport.iop_padir |= 0x0200;
-#if 0
- /* VCC switch error flag, PCMCIA slot INPACK_ pin */
- cp->cp_pbdir &= ~(0x0020 | 0x0010);
- cp->cp_pbpar &= ~(0x0020 | 0x0010);
- udelay(500000);
-#endif
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* remove all power */
- immap->im_ioport.iop_pcdat |= 0x0400;
- immap->im_ioport.iop_padat |= 0x0200;
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Ports A & C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn off all power
- */
- debug ("PCMCIA power OFF\n");
- immap->im_ioport.iop_pcpar &= ~(0x0400);
- immap->im_ioport.iop_pcso &= ~(0x0400);/*
- immap->im_ioport.iop_pcdir |= 0x0400;*/
-
- immap->im_ioport.iop_papar &= ~(0x0200);/*
- immap->im_ioport.iop_padir |= 0x0200;*/
-
- immap->im_ioport.iop_pcdat |= 0x0400;
- immap->im_ioport.iop_padat |= 0x0200;
-
- reg = 0;
- switch(vcc) {
- case 0: break;
- case 33: reg |= 0x0200; break;
- case 50: reg |= 0x0400; break;
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- if (reg & 0x0200)
- immap->im_ioport.iop_pcdat &= !reg;
- if (reg & 0x0400)
- immap->im_ioport.iop_padat &= !reg;
- immap->im_ioport.iop_pcdir |= 0x0200;
- immap->im_ioport.iop_padir |= 0x0400;
- if (reg) {
- debug ("PCMCIA powered at %sV\n",
- (reg&0x0400) ? "5.0" : "3.3");
- } else {
- debug ("PCMCIA powered down\n");
- }
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-#endif /* R360MPI */
-
-/* -------------------------------------------------------------------- */
-/* KUP4K and KUP4X Boards */
-/* -------------------------------------------------------------------- */
-#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
-
-#define PCMCIA_BOARD_MSG "KUP"
-
-#define KUP4K_PCMCIA_B_3V3 (0x00020000)
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(slot);
- pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
- udelay(2500);
-
- /*
- * Configure Port B pins for
- * 3 Volts enable
- */
- if (slot) { /* Slot A is built-in */
- cp->cp_pbdir |= KUP4K_PCMCIA_B_3V3;
- cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
- /* remove all power */
- cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3; /* active low */
- }
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- printf("%s Slot %c:", slot ? "" : "\n", 'A' + slot);
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
- if ((reg & mask) == mask) {
- puts (" 5.0V card found: NOT SUPPORTED !!!\n");
- } else {
- if(slot)
- cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
- puts (" 3.3V card found: ");
- }
-#if 0
- /* VCC switch error flag, PCMCIA slot INPACK_ pin */
- cp->cp_pbdir &= ~(0x0020 | 0x0010);
- cp->cp_pbpar &= ~(0x0020 | 0x0010);
- udelay(500000);
-#endif
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /* remove all power */
- if (slot)
- cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3;
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: " \
- PCMCIA_BOARD_MSG \
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- if (!slot) /* Slot A is not configurable */
- return 0;
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- debug ("PCMCIA power OFF\n");
- /*
- * Configure Port B pins for
- * 3 Volts enable
- */
- cp->cp_pbdir |= KUP4K_PCMCIA_B_3V3;
- cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
- /* remove all power */
- cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3; /* active low */
-
- switch(vcc) {
- case 0: break;
- case 33:
- cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
- debug ("PCMCIA powered at 3.3V\n");
- break;
- case 50:
- debug ("PCMCIA: 5Volt vcc not supported\n");
- break;
- default:
- puts("PCMCIA: vcc not supported");
- break;
- }
- udelay(10000);
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & (0x80000000 >> (slot << 4)))
- ? "only 5 V --> NOT SUPPORTED"
- : "can do 3.3V");
-
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-#endif /* KUP4K || KUP4X */
-
-
-/* -------------------------------------------------------------------- */
-/* End of Board Specific Stuff */
-/* -------------------------------------------------------------------- */
-
-
-/* -------------------------------------------------------------------- */
-/* MPC8xx Specific Stuff - should go to MPC8xx directory */
-/* -------------------------------------------------------------------- */
-
-/*
- * Search this table to see if the windowsize is
- * supported...
- */
-
-#define M8XX_SIZES_NO 32
-
-static const u_int m8xx_size_to_gray[M8XX_SIZES_NO] =
-{ 0x00000001, 0x00000002, 0x00000008, 0x00000004,
- 0x00000080, 0x00000040, 0x00000010, 0x00000020,
- 0x00008000, 0x00004000, 0x00001000, 0x00002000,
- 0x00000100, 0x00000200, 0x00000800, 0x00000400,
-
- 0x0fffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- 0x01000000, 0x02000000, 0xffffffff, 0x04000000,
- 0x00010000, 0x00020000, 0x00080000, 0x00040000,
- 0x00800000, 0x00400000, 0x00100000, 0x00200000 };
-
-
-/* -------------------------------------------------------------------- */
-
-#if ( ! defined(CONFIG_I82365) && ! defined(CONFIG_PXA_PCMCIA) )
-
-static u_int m8xx_get_graycode(u_int size)
-{
- u_int k;
-
- for (k = 0; k < M8XX_SIZES_NO; k++) {
- if(m8xx_size_to_gray[k] == size)
- break;
- }
-
- if((k == M8XX_SIZES_NO) || (m8xx_size_to_gray[k] == -1))
- k = -1;
-
- return k;
-}
-
-#endif /* CONFIG_I82365 */
-
-/* -------------------------------------------------------------------- */
-
-#if 0
-static u_int m8xx_get_speed(u_int ns, u_int is_io)
-{
- u_int reg, clocks, psst, psl, psht;
-
- if(!ns) {
-
- /*
- * We get called with IO maps setup to 0ns
- * if not specified by the user.
- * They should be 255ns.
- */
-
- if(is_io)
- ns = 255;
- else
- ns = 100; /* fast memory if 0 */
- }
-
- /*
- * In PSST, PSL, PSHT fields we tell the controller
- * timing parameters in CLKOUT clock cycles.
- * CLKOUT is the same as GCLK2_50.
- */
-
-/* how we want to adjust the timing - in percent */
-
-#define ADJ 180 /* 80 % longer accesstime - to be sure */
-
- clocks = ((M8XX_BUSFREQ / 1000) * ns) / 1000;
- clocks = (clocks * ADJ) / (100*1000);
-
- if(clocks >= PCMCIA_BMT_LIMIT) {
- DEBUG(0, "Max access time limit reached\n");
- clocks = PCMCIA_BMT_LIMIT-1;
- }
-
- psst = clocks / 7; /* setup time */
- psht = clocks / 7; /* hold time */
- psl = (clocks * 5) / 7; /* strobe length */
-
- psst += clocks - (psst + psht + psl);
-
- reg = psst << 12;
- reg |= psl << 7;
- reg |= psht << 16;
-
- return reg;
-}
-#endif
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-static void print_funcid (int func)
-{
- puts (indent);
- switch (func) {
- case CISTPL_FUNCID_MULTI:
- puts (" Multi-Function");
- break;
- case CISTPL_FUNCID_MEMORY:
- puts (" Memory");
- break;
- case CISTPL_FUNCID_SERIAL:
- puts (" Serial Port");
- break;
- case CISTPL_FUNCID_PARALLEL:
- puts (" Parallel Port");
- break;
- case CISTPL_FUNCID_FIXED:
- puts (" Fixed Disk");
- break;
- case CISTPL_FUNCID_VIDEO:
- puts (" Video Adapter");
- break;
- case CISTPL_FUNCID_NETWORK:
- puts (" Network Adapter");
- break;
- case CISTPL_FUNCID_AIMS:
- puts (" AIMS Card");
- break;
- case CISTPL_FUNCID_SCSI:
- puts (" SCSI Adapter");
- break;
- default:
- puts (" Unknown");
- break;
- }
- puts (" Card\n");
-}
-#endif /* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-static void print_fixed (volatile uchar *p)
-{
- if (p == NULL)
- return;
-
- puts(indent);
-
- switch (*p) {
- case CISTPL_FUNCE_IDE_IFACE:
- { uchar iface = *(p+2);
-
- puts ((iface == CISTPL_IDE_INTERFACE) ? " IDE" : " unknown");
- puts (" interface ");
- break;
- }
- case CISTPL_FUNCE_IDE_MASTER:
- case CISTPL_FUNCE_IDE_SLAVE:
- { uchar f1 = *(p+2);
- uchar f2 = *(p+4);
-
- puts ((f1 & CISTPL_IDE_SILICON) ? " [silicon]" : " [rotating]");
-
- if (f1 & CISTPL_IDE_UNIQUE)
- puts (" [unique]");
-
- puts ((f1 & CISTPL_IDE_DUAL) ? " [dual]" : " [single]");
-
- if (f2 & CISTPL_IDE_HAS_SLEEP)
- puts (" [sleep]");
-
- if (f2 & CISTPL_IDE_HAS_STANDBY)
- puts (" [standby]");
-
- if (f2 & CISTPL_IDE_HAS_IDLE)
- puts (" [idle]");
-
- if (f2 & CISTPL_IDE_LOW_POWER)
- puts (" [low power]");
-
- if (f2 & CISTPL_IDE_REG_INHIBIT)
- puts (" [reg inhibit]");
-
- if (f2 & CISTPL_IDE_HAS_INDEX)
- puts (" [index]");
-
- if (f2 & CISTPL_IDE_IOIS16)
- puts (" [IOis16]");
-
- break;
- }
- }
- putc ('\n');
-}
-#endif /* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-
-#define MAX_IDENT_CHARS 64
-#define MAX_IDENT_FIELDS 4
-
-static uchar *known_cards[] = {
- (uchar *)"ARGOSY PnPIDE D5",
- NULL
-};
-
-static int identify (volatile uchar *p)
-{
- uchar id_str[MAX_IDENT_CHARS];
- uchar data;
- uchar *t;
- uchar **card;
- int i, done;
-
- if (p == NULL)
- return (0); /* Don't know */
-
- t = id_str;
- done =0;
-
- for (i=0; i<=4 && !done; ++i, p+=2) {
- while ((data = *p) != '\0') {
- if (data == 0xFF) {
- done = 1;
- break;
- }
- *t++ = data;
- if (t == &id_str[MAX_IDENT_CHARS-1]) {
- done = 1;
- break;
- }
- p += 2;
- }
- if (!done)
- *t++ = ' ';
- }
- *t = '\0';
- while (--t > id_str) {
- if (*t == ' ')
- *t = '\0';
- else
- break;
- }
- puts ((char *)id_str);
- putc ('\n');
-
- for (card=known_cards; *card; ++card) {
- debug ("## Compare against \"%s\"\n", *card);
- if (strcmp((char *)*card, (char *)id_str) == 0) { /* found! */
- debug ("## CARD FOUND ##\n");
- return (1);
- }
- }
-
- return (0); /* don't know */
-}
-#endif /* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
-/* NETTA board by Intracom S.A. */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_NETTA)
-
-/* some sane bit macros */
-#define _BD(_b) (1U << (31-(_b)))
-#define _BDR(_l, _h) (((((1U << (31-(_l))) - 1) << 1) | 1) & ~((1U << (31-(_h))) - 1))
-
-#define _BW(_b) (1U << (15-(_b)))
-#define _BWR(_l, _h) (((((1U << (15-(_l))) - 1) << 1) | 1) & ~((1U << (15-(_h))) - 1))
-
-#define _BB(_b) (1U << (7-(_b)))
-#define _BBR(_l, _h) (((((1U << (7-(_l))) - 1) << 1) | 1) & ~((1U << (7-(_h))) - 1))
-
-#define _B(_b) _BD(_b)
-#define _BR(_l, _h) _BDR(_l, _h)
-
-#define PCMCIA_BOARD_MSG "NETTA"
-
-static const unsigned short vppd_masks[2] = { _BW(14), _BW(15) };
-
-static void cfg_vppd(int no)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
- return;
-
- mask = vppd_masks[no];
-
- immap->im_ioport.iop_papar &= ~mask;
- immap->im_ioport.iop_paodr &= ~mask;
- immap->im_ioport.iop_padir |= mask;
-}
-
-static void set_vppd(int no, int what)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
- return;
-
- mask = vppd_masks[no];
-
- if (what)
- immap->im_ioport.iop_padat |= mask;
- else
- immap->im_ioport.iop_padat &= ~mask;
-}
-
-static const unsigned short vccd_masks[2] = { _BW(10), _BW(6) };
-
-static void cfg_vccd(int no)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
- return;
-
- mask = vccd_masks[no];
-
- immap->im_ioport.iop_papar &= ~mask;
- immap->im_ioport.iop_paodr &= ~mask;
- immap->im_ioport.iop_padir |= mask;
-}
-
-static void set_vccd(int no, int what)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
- return;
-
- mask = vccd_masks[no];
-
- if (what)
- immap->im_ioport.iop_padat |= mask;
- else
- immap->im_ioport.iop_padat &= ~mask;
-}
-
-static const unsigned short oc_mask = _BW(8);
-
-static void cfg_oc(void)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask = oc_mask;
-
- immap->im_ioport.iop_pcdir &= ~mask;
- immap->im_ioport.iop_pcso &= ~mask;
- immap->im_ioport.iop_pcint &= ~mask;
- immap->im_ioport.iop_pcpar &= ~mask;
-}
-
-static int get_oc(void)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask = oc_mask;
- int what;
-
- what = !!(immap->im_ioport.iop_pcdat & mask);;
- return what;
-}
-
-static const unsigned short shdn_mask = _BW(12);
-
-static void cfg_shdn(void)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- mask = shdn_mask;
-
- immap->im_ioport.iop_papar &= ~mask;
- immap->im_ioport.iop_paodr &= ~mask;
- immap->im_ioport.iop_padir |= mask;
-}
-
-static void set_shdn(int what)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- unsigned short mask;
-
- mask = shdn_mask;
-
- if (what)
- immap->im_ioport.iop_padat |= mask;
- else
- immap->im_ioport.iop_padat &= ~mask;
-}
-
-static void cfg_ports (void);
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, pipr, mask;
- int i;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
- cfg_ports ();
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- pipr = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- pipr,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
-
- if ((pipr & mask) == mask) {
- set_vppd(0, 1); set_vppd(1, 1); /* VAVPP => Hi-Z */
- set_vccd(0, 0); set_vccd(1, 1); /* 5V on, 3V off */
- puts (" 5.0V card found: ");
- } else {
- set_vppd(0, 1); set_vppd(1, 1); /* VAVPP => Hi-Z */
- set_vccd(0, 1); set_vccd(1, 0); /* 5V off, 3V on */
- puts (" 3.3V card found: ");
- }
-
- /* Wait 500 ms; use this to check for over-current */
- for (i=0; i<5000; ++i) {
- if (!get_oc()) {
- printf (" *** Overcurrent - Safety shutdown ***\n");
- set_vccd(0, 0); set_vccd(1, 0); /* VAVPP => Hi-Z */
- return (1);
- }
- udelay (100);
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- /* All voltages off / Hi-Z */
- set_vppd(0, 1); set_vppd(1, 1);
- set_vccd(0, 1); set_vccd(1, 1);
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- ushort sreg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn all power pins to Hi-Z
- */
- debug ("PCMCIA power OFF\n");
- cfg_ports (); /* Enables switch, but all in Hi-Z */
-
- sreg = immap->im_ioport.iop_pcdat;
- set_vppd(0, 1); set_vppd(1, 1);
-
- switch(vcc) {
- case 0:
- break; /* Switch off */
-
- case 33:
- set_vccd(0, 1); set_vccd(1, 0);
- break;
-
- case 50:
- set_vccd(0, 0); set_vccd(1, 1);
- break;
-
- default:
- goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-static void cfg_ports (void)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
-
- immap = (immap_t *)CFG_IMMR;
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-
- cfg_vppd(0); cfg_vppd(1); /* VPPD0,VPPD1 VAVPP => Hi-Z */
- cfg_vccd(0); cfg_vccd(1); /* 3V and 5V off */
- cfg_shdn();
- cfg_oc();
-
- /*
- * Configure Port A for TPS2211 PC-Card Power-Interface Switch
- *
- * Switch off all voltages, assert shutdown
- */
- set_vppd(0, 1); set_vppd(1, 1);
- set_vccd(0, 0); set_vccd(1, 0);
- set_shdn(1);
-
- udelay(100000);
-}
-
-#endif /* NETTA */
-
-
-/* -------------------------------------------------------------------- */
-/* UC100 Boards */
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_UC100)
-
-#define PCMCIA_BOARD_MSG "UC100"
-
-/*
- * Remark: don't turn off OE "__MY_PCMCIA_GCRX_CXOE" on UC100 board.
- * This leads to board-hangup! (sr, 8 Dez. 2004)
- */
-
-static void cfg_ports (void);
-
-static int hardware_enable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- immap = (immap_t *)CFG_IMMR;
- sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
- /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
- cfg_ports ();
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
- if ((reg & mask) == mask) {
- puts (" 5.0V card found: ");
- } else {
- puts (" 3.3V card found: ");
- }
-
- /* switch VCC on */
- immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */
-
- udelay(10000);
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile cpm8xx_t *cp;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
- /* switch VCC off */
- immap->im_ioport.iop_padat &= ~0x8000; /* power disable 3.3V */
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif /* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- immap = (immap_t *)CFG_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable,
- * Turn all power pins to Hi-Z
- */
- debug ("PCMCIA power OFF\n");
- cfg_ports (); /* Enables switch, but all in Hi-Z */
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-static void cfg_ports (void)
-{
- volatile immap_t *immap;
-
- immap = (immap_t *)CFG_IMMR;
-
- /*
- * Configure Port A for MAX1602 PC-Card Power-Interface Switch
- */
- immap->im_ioport.iop_padat &= ~0x8000; /* set port x output to low */
- immap->im_ioport.iop_padir |= 0x8000; /* enable port x as output */
-
- debug ("Set Port A: PAR: %08x DIR: %08x DAT: %08x\n",
- immap->im_ioport.iop_papar, immap->im_ioport.iop_padir,
- immap->im_ioport.iop_padat);
-}
-
-#endif /* UC100 */
-
-
-/* -------------------------------------------------------------------- */
-
-#endif /* CFG_CMD_PCMCIA || (CFG_CMD_IDE && CONFIG_IDE_8xx_PCCARD) */
-
-/**************************************************/
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-U_BOOT_CMD(
- pinit, 2, 1, do_pinit,
- "pinit - PCMCIA sub-system\n",
- "on - power on PCMCIA socket\n"
- "pinit off - power off PCMCIA socket\n"
-);
-#endif
+#endif /* CHECK_IDE_DEVICE */
diff --git a/common/cmd_reginfo.c b/common/cmd_reginfo.c
index 15ac16a..f428f7e 100644
--- a/common/cmd_reginfo.c
+++ b/common/cmd_reginfo.c
@@ -328,7 +328,7 @@
(*(volatile ulong*)MPC5XXX_ADDECR & 0x02000000) ? 1 : 0);
printf ("\tSDRAMCS0: %08X\n",
*(volatile ulong*)MPC5XXX_SDRAM_CS0CFG);
- printf ("\tSDRAMCS0: %08X\n",
+ printf ("\tSDRAMCS1: %08X\n",
*(volatile ulong*)MPC5XXX_SDRAM_CS1CFG);
#endif /* CONFIG_MPC5200 */
return 0;
diff --git a/common/cmd_usb.c b/common/cmd_usb.c
index fdfd042..28c05aa 100644
--- a/common/cmd_usb.c
+++ b/common/cmd_usb.c
@@ -186,7 +186,7 @@
void usb_display_if_desc(struct usb_interface_descriptor *ifdesc,struct usb_device *dev)
{
printf(" Interface: %d\n",ifdesc->bInterfaceNumber);
- printf(" - Alternate Settings %d, Endpoints: %d\n",ifdesc->bAlternateSetting,ifdesc->bNumEndpoints);
+ printf(" - Alternate Setting %d, Endpoints: %d\n",ifdesc->bAlternateSetting,ifdesc->bNumEndpoints);
printf(" - Class ");
usb_display_class_sub(ifdesc->bInterfaceClass,ifdesc->bInterfaceSubClass,ifdesc->bInterfaceProtocol);
printf("\n");
@@ -444,6 +444,7 @@
int i;
struct usb_device *dev = NULL;
+ extern char usb_started;
#ifdef CONFIG_USB_STORAGE
block_dev_desc_t *stor_dev;
#endif
@@ -477,6 +478,10 @@
usb_stop();
return 0;
}
+ if (!usb_started) {
+ printf("USB is stopped. Please issue 'usb start' first.\n");
+ return 1;
+ }
if (strncmp(argv[1],"tree",4) == 0) {
printf("\nDevice Tree:\n");
usb_show_tree(usb_get_dev_index(0));
diff --git a/common/crc16.c b/common/crc16.c
index 3cef106..6904365 100644
--- a/common/crc16.c
+++ b/common/crc16.c
@@ -101,7 +101,7 @@
cksum = 0;
for (i = 0; i < len; i++) {
- cksum = crc16_tab[((cksum>>8) ^ *buf++) & 0xFF] ^ (cksum << 8);
+ cksum = crc16_tab[((cksum>>8) ^ *buf++) & 0xFF] ^ (cksum << 8);
}
return cksum;
}
diff --git a/common/main.c b/common/main.c
index 758ef8d..13d12a4 100644
--- a/common/main.c
+++ b/common/main.c
@@ -2,6 +2,10 @@
* (C) Copyright 2000
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
+ * Add to readline cmdline-editing by
+ * (C) Copyright 2005
+ * JinHua Luo, GuangDong Linux Center, <luo.jinhua@gd-linux.com>
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
@@ -49,7 +53,6 @@
#define MAX_DELAY_STOP_STR 32
-static char * delete_char (char *buffer, char *p, int *colp, int *np, int plen);
static int parse_line (char *, char *[]);
#if defined(CONFIG_BOOTDELAY) && (CONFIG_BOOTDELAY >= 0)
static int abortboot(int);
@@ -59,8 +62,11 @@
char console_buffer[CFG_CBSIZE]; /* console I/O buffer */
+#ifndef CONFIG_CMDLINE_EDITING
+static char * delete_char (char *buffer, char *p, int *colp, int *np, int plen);
static char erase_seq[] = "\b \b"; /* erase sequence */
static char tab_seq[] = " "; /* used to expand TABs */
+#endif /* CONFIG_CMDLINE_EDITING */
#ifdef CONFIG_BOOT_RETRY_TIME
static uint64_t endtime = 0; /* must be set, default is instant timeout */
@@ -516,6 +522,406 @@
}
#endif
+#ifdef CONFIG_CMDLINE_EDITING
+
+/*
+ * cmdline-editing related codes from vivi.
+ * Author: Janghoon Lyu <nandy@mizi.com>
+ */
+
+#if 1 /* avoid redundand code -- wd */
+#define putnstr(str,n) do { \
+ printf ("%.*s", n, str); \
+ } while (0)
+#else
+void putnstr(const char *str, size_t n)
+{
+ if (str == NULL)
+ return;
+
+ while (n && *str != '\0') {
+ putc(*str);
+ str++;
+ n--;
+ }
+}
+#endif
+
+#define CTL_CH(c) ((c) - 'a' + 1)
+
+#define MAX_CMDBUF_SIZE 256
+
+#define CTL_BACKSPACE ('\b')
+#define DEL ((char)255)
+#define DEL7 ((char)127)
+#define CREAD_HIST_CHAR ('!')
+
+#define getcmd_putch(ch) putc(ch)
+#define getcmd_getch() getc()
+#define getcmd_cbeep() getcmd_putch('\a')
+
+#define HIST_MAX 20
+#define HIST_SIZE MAX_CMDBUF_SIZE
+
+static int hist_max = 0;
+static int hist_add_idx = 0;
+static int hist_cur = -1;
+unsigned hist_num = 0;
+
+char* hist_list[HIST_MAX];
+char hist_lines[HIST_MAX][HIST_SIZE];
+
+#define add_idx_minus_one() ((hist_add_idx == 0) ? hist_max : hist_add_idx-1)
+
+static void hist_init(void)
+{
+ int i;
+
+ hist_max = 0;
+ hist_add_idx = 0;
+ hist_cur = -1;
+ hist_num = 0;
+
+ for (i = 0; i < HIST_MAX; i++) {
+ hist_list[i] = hist_lines[i];
+ hist_list[i][0] = '\0';
+ }
+}
+
+static void cread_add_to_hist(char *line)
+{
+ strcpy(hist_list[hist_add_idx], line);
+
+ if (++hist_add_idx >= HIST_MAX)
+ hist_add_idx = 0;
+
+ if (hist_add_idx > hist_max)
+ hist_max = hist_add_idx;
+
+ hist_num++;
+}
+
+static char* hist_prev(void)
+{
+ char *ret;
+ int old_cur;
+
+ if (hist_cur < 0)
+ return NULL;
+
+ old_cur = hist_cur;
+ if (--hist_cur < 0)
+ hist_cur = hist_max;
+
+ if (hist_cur == hist_add_idx) {
+ hist_cur = old_cur;
+ ret = NULL;
+ } else
+ ret = hist_list[hist_cur];
+
+ return (ret);
+}
+
+static char* hist_next(void)
+{
+ char *ret;
+
+ if (hist_cur < 0)
+ return NULL;
+
+ if (hist_cur == hist_add_idx)
+ return NULL;
+
+ if (++hist_cur > hist_max)
+ hist_cur = 0;
+
+ if (hist_cur == hist_add_idx) {
+ ret = "";
+ } else
+ ret = hist_list[hist_cur];
+
+ return (ret);
+}
+
+#ifndef CONFIG_CMDLINE_EDITING
+static void cread_print_hist_list(void)
+{
+ int i;
+ unsigned long n;
+
+ n = hist_num - hist_max;
+
+ i = hist_add_idx + 1;
+ while (1) {
+ if (i > hist_max)
+ i = 0;
+ if (i == hist_add_idx)
+ break;
+ printf("%s\n", hist_list[i]);
+ n++;
+ i++;
+ }
+}
+#endif /* CONFIG_CMDLINE_EDITING */
+
+#define BEGINNING_OF_LINE() { \
+ while (num) { \
+ getcmd_putch(CTL_BACKSPACE); \
+ num--; \
+ } \
+}
+
+#define ERASE_TO_EOL() { \
+ if (num < eol_num) { \
+ int tmp; \
+ for (tmp = num; tmp < eol_num; tmp++) \
+ getcmd_putch(' '); \
+ while (tmp-- > num) \
+ getcmd_putch(CTL_BACKSPACE); \
+ eol_num = num; \
+ } \
+}
+
+#define REFRESH_TO_EOL() { \
+ if (num < eol_num) { \
+ wlen = eol_num - num; \
+ putnstr(buf + num, wlen); \
+ num = eol_num; \
+ } \
+}
+
+static void cread_add_char(char ichar, int insert, unsigned long *num,
+ unsigned long *eol_num, char *buf, unsigned long len)
+{
+ unsigned long wlen;
+
+ /* room ??? */
+ if (insert || *num == *eol_num) {
+ if (*eol_num > len - 1) {
+ getcmd_cbeep();
+ return;
+ }
+ (*eol_num)++;
+ }
+
+ if (insert) {
+ wlen = *eol_num - *num;
+ if (wlen > 1) {
+ memmove(&buf[*num+1], &buf[*num], wlen-1);
+ }
+
+ buf[*num] = ichar;
+ putnstr(buf + *num, wlen);
+ (*num)++;
+ while (--wlen) {
+ getcmd_putch(CTL_BACKSPACE);
+ }
+ } else {
+ /* echo the character */
+ wlen = 1;
+ buf[*num] = ichar;
+ putnstr(buf + *num, wlen);
+ (*num)++;
+ }
+}
+
+static void cread_add_str(char *str, int strsize, int insert, unsigned long *num,
+ unsigned long *eol_num, char *buf, unsigned long len)
+{
+ while (strsize--) {
+ cread_add_char(*str, insert, num, eol_num, buf, len);
+ str++;
+ }
+}
+
+static int cread_line(char *buf, unsigned int *len)
+{
+ unsigned long num = 0;
+ unsigned long eol_num = 0;
+ unsigned long rlen;
+ unsigned long wlen;
+ char ichar;
+ int insert = 1;
+ int esc_len = 0;
+ int rc = 0;
+ char esc_save[8];
+
+ while (1) {
+ rlen = 1;
+ ichar = getcmd_getch();
+
+ if ((ichar == '\n') || (ichar == '\r')) {
+ putc('\n');
+ break;
+ }
+
+ /*
+ * handle standard linux xterm esc sequences for arrow key, etc.
+ */
+ if (esc_len != 0) {
+ if (esc_len == 1) {
+ if (ichar == '[') {
+ esc_save[esc_len] = ichar;
+ esc_len = 2;
+ } else {
+ cread_add_str(esc_save, esc_len, insert,
+ &num, &eol_num, buf, *len);
+ esc_len = 0;
+ }
+ continue;
+ }
+
+ switch (ichar) {
+
+ case 'D': /* <- key */
+ ichar = CTL_CH('b');
+ esc_len = 0;
+ break;
+ case 'C': /* -> key */
+ ichar = CTL_CH('f');
+ esc_len = 0;
+ break; /* pass off to ^F handler */
+ case 'H': /* Home key */
+ ichar = CTL_CH('a');
+ esc_len = 0;
+ break; /* pass off to ^A handler */
+ case 'A': /* up arrow */
+ ichar = CTL_CH('p');
+ esc_len = 0;
+ break; /* pass off to ^P handler */
+ case 'B': /* down arrow */
+ ichar = CTL_CH('n');
+ esc_len = 0;
+ break; /* pass off to ^N handler */
+ default:
+ esc_save[esc_len++] = ichar;
+ cread_add_str(esc_save, esc_len, insert,
+ &num, &eol_num, buf, *len);
+ esc_len = 0;
+ continue;
+ }
+ }
+
+ switch (ichar) {
+ case 0x1b:
+ if (esc_len == 0) {
+ esc_save[esc_len] = ichar;
+ esc_len = 1;
+ } else {
+ puts("impossible condition #876\n");
+ esc_len = 0;
+ }
+ break;
+
+ case CTL_CH('a'):
+ BEGINNING_OF_LINE();
+ break;
+ case CTL_CH('c'): /* ^C - break */
+ *buf = '\0'; /* discard input */
+ return (-1);
+ case CTL_CH('f'):
+ if (num < eol_num) {
+ getcmd_putch(buf[num]);
+ num++;
+ }
+ break;
+ case CTL_CH('b'):
+ if (num) {
+ getcmd_putch(CTL_BACKSPACE);
+ num--;
+ }
+ break;
+ case CTL_CH('d'):
+ if (num < eol_num) {
+ wlen = eol_num - num - 1;
+ if (wlen) {
+ memmove(&buf[num], &buf[num+1], wlen);
+ putnstr(buf + num, wlen);
+ }
+
+ getcmd_putch(' ');
+ do {
+ getcmd_putch(CTL_BACKSPACE);
+ } while (wlen--);
+ eol_num--;
+ }
+ break;
+ case CTL_CH('k'):
+ ERASE_TO_EOL();
+ break;
+ case CTL_CH('e'):
+ REFRESH_TO_EOL();
+ break;
+ case CTL_CH('o'):
+ insert = !insert;
+ break;
+ case CTL_CH('x'):
+ BEGINNING_OF_LINE();
+ ERASE_TO_EOL();
+ break;
+ case DEL:
+ case DEL7:
+ case 8:
+ if (num) {
+ wlen = eol_num - num;
+ num--;
+ memmove(&buf[num], &buf[num+1], wlen);
+ getcmd_putch(CTL_BACKSPACE);
+ putnstr(buf + num, wlen);
+ getcmd_putch(' ');
+ do {
+ getcmd_putch(CTL_BACKSPACE);
+ } while (wlen--);
+ eol_num--;
+ }
+ break;
+ case CTL_CH('p'):
+ case CTL_CH('n'):
+ {
+ char * hline;
+
+ esc_len = 0;
+
+ if (ichar == CTL_CH('p'))
+ hline = hist_prev();
+ else
+ hline = hist_next();
+
+ if (!hline) {
+ getcmd_cbeep();
+ continue;
+ }
+
+ /* nuke the current line */
+ /* first, go home */
+ BEGINNING_OF_LINE();
+
+ /* erase to end of line */
+ ERASE_TO_EOL();
+
+ /* copy new line into place and display */
+ strcpy(buf, hline);
+ eol_num = strlen(buf);
+ REFRESH_TO_EOL();
+ continue;
+ }
+ default:
+ cread_add_char(ichar, insert, &num, &eol_num, buf, *len);
+ break;
+ }
+ }
+ *len = eol_num;
+ buf[eol_num] = '\0'; /* lose the newline */
+
+ if (buf[0] && buf[0] != CREAD_HIST_CHAR)
+ cread_add_to_hist(buf);
+ hist_cur = hist_add_idx;
+
+ return (rc);
+}
+
+#endif /* CONFIG_CMDLINE_EDITING */
+
/****************************************************************************/
/*
@@ -528,6 +934,22 @@
*/
int readline (const char *const prompt)
{
+#ifdef CONFIG_CMDLINE_EDITING
+ char *p = console_buffer;
+ unsigned int len=MAX_CMDBUF_SIZE;
+ int rc;
+ static int initted = 0;
+
+ if (!initted) {
+ hist_init();
+ initted = 1;
+ }
+
+ puts (prompt);
+
+ rc = cread_line(p, &len);
+ return rc < 0 ? rc : len;
+#else
char *p = console_buffer;
int n = 0; /* buffer index */
int plen = 0; /* prompt length */
@@ -623,10 +1045,12 @@
}
}
}
+#endif /* CONFIG_CMDLINE_EDITING */
}
/****************************************************************************/
+#ifndef CONFIG_CMDLINE_EDITING
static char * delete_char (char *buffer, char *p, int *colp, int *np, int plen)
{
char *s;
@@ -656,6 +1080,7 @@
(*np)--;
return (p);
}
+#endif /* CONFIG_CMDLINE_EDITING */
/****************************************************************************/
diff --git a/common/serial.c b/common/serial.c
index 7b29951..38057d2 100644
--- a/common/serial.c
+++ b/common/serial.c
@@ -42,7 +42,11 @@
return &serial_scc_device;
#elif defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
|| defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
- return &serial0_device;
+#if defined(CONFIG_UART1_CONSOLE)
+ return &serial1_device;
+#else
+ return &serial0_device;
+#endif
#else
#error No default console
#endif
diff --git a/common/usb.c b/common/usb.c
index d9515e6..0857494 100644
--- a/common/usb.c
+++ b/common/usb.c
@@ -72,6 +72,8 @@
static int asynch_allowed;
static struct devrequest setup_packet;
+char usb_started; /* flag for the started/stopped USB status */
+
/**********************************************************************
* some forward declerations...
*/
@@ -110,10 +112,12 @@
printf("scanning bus for devices... ");
running=1;
usb_scan_devices();
+ usb_started = 1;
return 0;
}
else {
printf("Error, couldn't init Lowlevel part\n");
+ usb_started = 0;
return -1;
}
}
@@ -124,6 +128,7 @@
int usb_stop(void)
{
asynch_allowed=1;
+ usb_started = 0;
usb_hub_reset();
return usb_lowlevel_stop();
}
@@ -280,56 +285,68 @@
int usb_parse_config(struct usb_device *dev, unsigned char *buffer, int cfgno)
{
struct usb_descriptor_header *head;
- int index,ifno,epno;
- ifno=-1;
- epno=-1;
+ int index, ifno, epno, curr_if_num;
+ int i;
+ unsigned char *ch;
- dev->configno=cfgno;
- head =(struct usb_descriptor_header *)&buffer[0];
- if(head->bDescriptorType!=USB_DT_CONFIG) {
- printf(" ERROR: NOT USB_CONFIG_DESC %x\n",head->bDescriptorType);
+ ifno = -1;
+ epno = -1;
+ curr_if_num = -1;
+
+ dev->configno = cfgno;
+ head = (struct usb_descriptor_header *) &buffer[0];
+ if(head->bDescriptorType != USB_DT_CONFIG) {
+ printf(" ERROR: NOT USB_CONFIG_DESC %x\n", head->bDescriptorType);
return -1;
}
- memcpy(&dev->config,buffer,buffer[0]);
- dev->config.wTotalLength=swap_16(dev->config.wTotalLength);
- dev->config.no_of_if=0;
+ memcpy(&dev->config, buffer, buffer[0]);
+ dev->config.wTotalLength = swap_16(dev->config.wTotalLength);
+ dev->config.no_of_if = 0;
- index=dev->config.bLength;
+ index = dev->config.bLength;
/* Ok the first entry must be a configuration entry, now process the others */
- head=(struct usb_descriptor_header *)&buffer[index];
- while(index+1 < dev->config.wTotalLength) {
+ head = (struct usb_descriptor_header *) &buffer[index];
+ while(index + 1 < dev->config.wTotalLength) {
switch(head->bDescriptorType) {
case USB_DT_INTERFACE:
- ifno=dev->config.no_of_if;
- dev->config.no_of_if++; /* found an interface desc, increase numbers */
- memcpy(&dev->config.if_desc[ifno],&buffer[index],buffer[index]); /* copy new desc */
- dev->config.if_desc[ifno].no_of_ep=0;
-
+ if(((struct usb_interface_descriptor *) &buffer[index])->
+ bInterfaceNumber != curr_if_num) {
+ /* this is a new interface, copy new desc */
+ ifno = dev->config.no_of_if;
+ dev->config.no_of_if++;
+ memcpy(&dev->config.if_desc[ifno],
+ &buffer[index], buffer[index]);
+ dev->config.if_desc[ifno].no_of_ep = 0;
+ dev->config.if_desc[ifno].num_altsetting = 1;
+ curr_if_num = dev->config.if_desc[ifno].bInterfaceNumber;
+ } else {
+ /* found alternate setting for the interface */
+ dev->config.if_desc[ifno].num_altsetting++;
+ }
break;
case USB_DT_ENDPOINT:
- epno=dev->config.if_desc[ifno].no_of_ep;
+ epno = dev->config.if_desc[ifno].no_of_ep;
dev->config.if_desc[ifno].no_of_ep++; /* found an endpoint */
- memcpy(&dev->config.if_desc[ifno].ep_desc[epno],&buffer[index],buffer[index]);
- dev->config.if_desc[ifno].ep_desc[epno].wMaxPacketSize
- =swap_16(dev->config.if_desc[ifno].ep_desc[epno].wMaxPacketSize);
- USB_PRINTF("if %d, ep %d\n",ifno,epno);
+ memcpy(&dev->config.if_desc[ifno].ep_desc[epno],
+ &buffer[index], buffer[index]);
+ dev->config.if_desc[ifno].ep_desc[epno].wMaxPacketSize =
+ swap_16(dev->config.if_desc[ifno].ep_desc[epno].wMaxPacketSize);
+ USB_PRINTF("if %d, ep %d\n", ifno, epno);
break;
default:
- if(head->bLength==0)
+ if(head->bLength == 0)
return 1;
- USB_PRINTF("unknown Description Type : %x\n",head->bDescriptorType);
+ USB_PRINTF("unknown Description Type : %x\n", head->bDescriptorType);
{
- int i;
- unsigned char *ch;
- ch=(unsigned char *)head;
- for(i=0;i<head->bLength; i++)
- USB_PRINTF("%02X ",*ch++);
+ ch = (unsigned char *)head;
+ for(i = 0; i < head->bLength; i++)
+ USB_PRINTF("%02X ", *ch++);
USB_PRINTF("\n\n\n");
}
break;
}
- index+=head->bLength;
- head=(struct usb_descriptor_header *)&buffer[index];
+ index += head->bLength;
+ head = (struct usb_descriptor_header *)&buffer[index];
}
return 1;
}
@@ -443,6 +460,14 @@
printf("selecting invalid interface %d", interface);
return -1;
}
+ /*
+ * We should return now for devices with only one alternate setting.
+ * According to 9.4.10 of the Universal Serial Bus Specification Revision 2.0
+ * such devices can return with a STALL. This results in some USB sticks
+ * timeouting during initialization and then being unusable in U-Boot.
+ */
+ if (if_face->num_altsetting == 1)
+ return 0;
if ((ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
USB_REQ_SET_INTERFACE, USB_RECIP_INTERFACE, alternate,
diff --git a/common/usb_storage.c b/common/usb_storage.c
index 99e4ab0..e64470c 100644
--- a/common/usb_storage.c
+++ b/common/usb_storage.c
@@ -1139,6 +1139,10 @@
/* USB007 Mini-USB2 Flash Drive */
(dev->descriptor.idVendor == 0x066f &&
dev->descriptor.idProduct == 0x2010)
+ ||
+ /* SanDisk Corporation Cruzer Micro 20044318410546613953 */
+ (dev->descriptor.idVendor == 0x0781 &&
+ dev->descriptor.idProduct == 0x5151)
)
USB_STOR_PRINTF("usb_stor_get_info: skipping RESET..\n");
else
diff --git a/common/xyzModem.c b/common/xyzModem.c
index 9b455a3..d1d66e8 100644
--- a/common/xyzModem.c
+++ b/common/xyzModem.c
@@ -261,8 +261,8 @@
static void
zm_flush(void)
{
- char *p = zm_out_start;
#ifdef REDBOOT
+ char *p = zm_out_start;
while (*p) mon_write_char(*p++);
#endif
zm_out = zm_out_start;
diff --git a/cpu/arm920t/s3c24x0/interrupts.c b/cpu/arm920t/s3c24x0/interrupts.c
index 3ec9b54..1b36412 100644
--- a/cpu/arm920t/s3c24x0/interrupts.c
+++ b/cpu/arm920t/s3c24x0/interrupts.c
@@ -176,7 +176,9 @@
#if defined(CONFIG_SMDK2400) || defined(CONFIG_TRAB)
tbclk = timer_load_val * 100;
-#elif defined(CONFIG_SMDK2410) || defined(CONFIG_VCMA9)
+#elif defined(CONFIG_SBC2410X) || \
+ defined(CONFIG_SMDK2410) || \
+ defined(CONFIG_VCMA9)
tbclk = CFG_HZ;
#else
# error "tbclk not configured"
diff --git a/cpu/i386/sc520.c b/cpu/i386/sc520.c
index c83f0bb..1c4370b 100644
--- a/cpu/i386/sc520.c
+++ b/cpu/i386/sc520.c
@@ -31,7 +31,9 @@
#include <common.h>
#include <config.h>
#include <pci.h>
+#ifdef CONFIG_SC520_SSI
#include <ssi.h>
+#endif
#include <asm/io.h>
#include <asm/pci.h>
#include <asm/ic/sc520.h>
@@ -143,7 +145,15 @@
u32 dram_present=0;
u32 dram_ctrl;
-
+#ifdef CFG_SDRAM_DRCTMCTL
+ /* these memory control registers are set up in the assember part,
+ * in sc520_asm.S, during 'mem_init'. If we muck with them here,
+ * after we are running a stack in RAM, we have troubles. Besides,
+ * these refresh and delay values are better ? simply specified
+ * outright in the include/configs/{cfg} file since the HW designer
+ * simply dictates it.
+ */
+#else
int val;
int cas_precharge_delay = CFG_SDRAM_PRECHARGE_DELAY;
@@ -162,6 +172,7 @@
} else {
val = 3; /* 62.4us */
}
+
write_mmcr_byte(SC520_DRCCTL, (read_mmcr_byte(SC520_DRCCTL) & 0xcf) | (val<<4));
val = read_mmcr_byte(SC520_DRCTMCTL);
@@ -181,13 +192,12 @@
val |= 1;
}
write_mmcr_byte(SC520_DRCTMCTL, val);
-
+#endif
/* We read-back the configuration of the dram
* controller that the assembly code wrote */
dram_ctrl = read_mmcr_long(SC520_DRCBENDADR);
-
bd->bi_dram[0].start = 0;
if (dram_ctrl & 0x80) {
/* bank 0 enabled */
@@ -274,7 +284,7 @@
{
int i;
-# if 0
+# if 1
printf("set_irq(): map INT%c to IRQ%d\n", pci_pin + 'A', irq);
#endif
if (irq < 0 || irq > 15) {
diff --git a/cpu/i386/sc520_asm.S b/cpu/i386/sc520_asm.S
index 80464fa..e1fa37a 100644
--- a/cpu/i386/sc520_asm.S
+++ b/cpu/i386/sc520_asm.S
@@ -113,6 +113,7 @@
.equ DRCCFG, 0x0fffef014 /* DRAM bank configuration register */
.equ DRCBENDADR, 0x0fffef018 /* DRAM bank ending address register */
.equ ECCCTL, 0x0fffef020 /* DRAM ECC control register */
+.equ ECCINT, 0x0fffefd18 /* DRAM ECC nmi-INT mapping */
.equ DBCTL, 0x0fffef040 /* DRAM buffer control register */
.equ CACHELINESZ, 0x00000010 /* size of our cache line (read buffer) */
@@ -459,6 +460,12 @@
incl %edi
loop cleanuplp
+#if defined CFG_SDRAM_DRCTMCTL
+ /* just have your hardware desinger _GIVE_ you what you need here! */
+ movl $DRCTMCTL, %edi
+ movb $CFG_SDRAM_DRCTMCTL,%al
+ movb (%edi), %al
+#else
#if defined(CFG_SDRAM_CAS_LATENCY_2T) || defined(CFG_SDRAM_CAS_LATENCY_3T)
/* set the CAS latency now since it is hard to do
* when we run from the RAM */
@@ -470,7 +477,8 @@
#ifdef CFG_SDRAM_CAS_LATENCY_3T
orb $0x10, %al
#endif
- movb %al, (%edi)
+ movb %al, (%edi)
+#endif
#endif
movl $DRCCTL, %edi /* DRAM Control register */
movb $0x3,%al /* Load mode register cmd */
@@ -528,9 +536,49 @@
shll $22, %eax
movl %eax, %ebx
-done: movl %ebx, %eax
+done:
+ movl %ebx, %eax
+
+#if CFG_SDRAM_ECC_ENABLE
+ /* A nominal memory test: just a byte at each address line */
+ movl %eax, %ecx
+ shrl $0x1, %ecx
+ movl $0x1, %edi
+memtest0:
+ movb $0xa5, (%edi)
+ cmpb $0xa5, (%edi)
+ jne out
+ shrl $1, %ecx
+ andl %ecx,%ecx
+ jz set_ecc
+ shll $1, %edi
+ jmp memtest0
+
+set_ecc:
+ /* clear all ram with a memset */
+ movl %eax, %ecx
+ xorl %esi, %esi
+ xorl %edi, %edi
+ xorl %eax, %eax
+ shrl $2, %ecx
+ cld
+ rep stosl
+ /* enable read, write buffers */
+ movb $0x11, %al
+ movl $DBCTL, %edi
+ movb %al, (%edi)
+ /* enable NMI mapping for ECC */
+ movl $ECCINT, %edi
+ mov $0x10, %al
+ movb %al, (%edi)
+ /* Turn on ECC */
+ movl $ECCCTL, %edi
+ mov $0x05, %al
+ movb %al, (%edi)
+#endif
+out:
+ movl %ebx, %eax
jmp *%ebp
-
#endif /* CONFIG_SC520 */
diff --git a/cpu/mips/config.mk b/cpu/mips/config.mk
index c357615..b29986e 100644
--- a/cpu/mips/config.mk
+++ b/cpu/mips/config.mk
@@ -21,7 +21,7 @@
# MA 02111-1307 USA
#
v=$(shell \
-mips-linux-as --version|grep "GNU assembler"|awk '{print $$3}'|awk -F . '{print $$2}')
+$(CROSS_COMPILE)as --version|grep "GNU assembler"|awk '{print $$3}'|awk -F . '{print $$2}')
MIPSFLAGS=$(shell \
if [ "$v" -lt "14" ]; then \
echo "-mcpu=4kc"; \
diff --git a/cpu/mpc8xx/cpu_init.c b/cpu/mpc8xx/cpu_init.c
index 1a7111f..c79e578 100644
--- a/cpu/mpc8xx/cpu_init.c
+++ b/cpu/mpc8xx/cpu_init.c
@@ -161,6 +161,7 @@
defined(CONFIG_RMU) || \
defined(CONFIG_RPXCLASSIC) || \
defined(CONFIG_RPXLITE) || \
+ defined(CONFIG_SPC1920) || \
defined(CONFIG_SPD823TS)
memctl->memc_br0 = CFG_BR0_PRELIM;
diff --git a/cpu/mpc8xx/fec.c b/cpu/mpc8xx/fec.c
index 6006478..6d2755e 100644
--- a/cpu/mpc8xx/fec.c
+++ b/cpu/mpc8xx/fec.c
@@ -396,8 +396,10 @@
* * to 2.5 MHz.
* * This MDC frequency is equal to system clock / (2 * MII_SPEED).
* * Then MII_SPEED = system_clock / 2 * 2,5 Mhz.
+ *
+ * All MII configuration is done via FEC1 registers:
*/
- fecp->fec_mii_speed = ((bd->bi_intfreq + 4999999) / 5000000) << 1;
+ immr->im_cpm.cp_fec1.fec_mii_speed = ((bd->bi_intfreq + 4999999) / 5000000) << 1;
#if defined(CONFIG_NETTA) || defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2)
/* our PHYs are the limit at 2.5 MHz */
@@ -508,8 +510,6 @@
#if defined(CONFIG_MPC885_FAMILY) /* MPC87x/88x have got 2 FECs and different pinout */
#if !defined(CONFIG_RMII)
-
-#warning this configuration is not tested; please report if it works
immr->im_cpm.cp_pepar |= 0x0003fffc;
immr->im_cpm.cp_pedir |= 0x0003fffc;
immr->im_cpm.cp_peso &= ~0x000087fc;
@@ -822,6 +822,7 @@
#define PHY_ID_LSI80225 0x0016f870 /* LSI 80225 */
#define PHY_ID_LSI80225B 0x0016f880 /* LSI 80225/B */
#define PHY_ID_DM9161 0x0181B880 /* Davicom DM9161 */
+#define PHY_ID_KSM8995M 0x00221450 /* MICREL KS8995MA */
/* send command to phy using mii, wait for result */
static uint
@@ -907,6 +908,9 @@
case PHY_ID_DM9161:
printf("Davicom DM9161\n");
break;
+ case PHY_ID_KSM8995M:
+ printf("MICREL KS8995M\n");
+ break;
default:
printf("0x%08x\n", phytype);
break;
diff --git a/cpu/mpc8xx/serial.c b/cpu/mpc8xx/serial.c
index 26a82cc..8ae584f 100644
--- a/cpu/mpc8xx/serial.c
+++ b/cpu/mpc8xx/serial.c
@@ -227,9 +227,12 @@
sp->smc_smcm = 0;
sp->smc_smce = 0xff;
- /* Set up the baud rate generator.
- */
+#ifdef CFG_SPC1920_SMC1_CLK4 /* clock source is PLD */
+ *((volatile uchar *) CFG_SPC1920_PLD_BASE+6) = 0xff;
+#else
+ /* Set up the baud rate generator */
smc_setbrg ();
+#endif
/* Make the first buffer the only buffer.
*/
diff --git a/cpu/mpc8xx/speed.c b/cpu/mpc8xx/speed.c
index 57f91c0..101d5f9 100644
--- a/cpu/mpc8xx/speed.c
+++ b/cpu/mpc8xx/speed.c
@@ -259,7 +259,11 @@
*/
sccr_reg = immr->im_clkrst.car_sccr;
sccr_reg &= ~SCCR_EBDF11;
+#if defined(CONFIG_TQM885D)
+ if (gd->cpu_clk <= 80000000) {
+#else
if (gd->cpu_clk <= 66000000) {
+#endif
sccr_reg |= SCCR_EBDF00; /* bus division factor = 1 */
gd->bus_clk = gd->cpu_clk;
} else {
@@ -360,7 +364,8 @@
#endif /* CONFIG_8xx_CPUCLK_DEFAULT */
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M)
+#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) \
+ && !defined(CONFIG_TQM885D)
/*
* Adjust sdram refresh rate to actual CPU clock
* and set timebase source according to actual CPU clock
@@ -384,6 +389,6 @@
return (0);
}
-#endif /* CONFIG_TQM8xxL/M, !TQM866M */
+#endif /* CONFIG_TQM8xxL/M, !TQM866M, !TQM885D */
/* ------------------------------------------------------------------------- */
diff --git a/cpu/ppc4xx/405gp_pci.c b/cpu/ppc4xx/405gp_pci.c
index fad895b..0b0686b 100644
--- a/cpu/ppc4xx/405gp_pci.c
+++ b/cpu/ppc4xx/405gp_pci.c
@@ -315,7 +315,6 @@
#ifdef CONFIG_PCI_SCAN_SHOW
printf("PCI: Bus Dev VenId DevId Class Int\n");
#endif
-
hose->last_busno = pci_hose_scan(hose);
}
#endif /* CONFIG_PCI_PNP */
@@ -438,7 +437,7 @@
* The PCI initialization sequence enable bit must be set ... if not abort
* pci setup since updating the bit requires chip reset.
*--------------------------------------------------------------------------*/
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
unsigned long strap;
mfsdr(sdr_sdstp1,strap);
@@ -465,17 +464,30 @@
hose->first_busno = 0;
hose->last_busno = 0xff;
+ /* PCI I/O space */
pci_set_region(hose->regions + reg_num++,
0x00000000,
PCIX0_IOBASE,
0x10000,
PCI_REGION_IO);
+ /* PCI memory space */
pci_set_region(hose->regions + reg_num++,
CFG_PCI_TARGBASE,
CFG_PCI_MEMBASE,
0x10000000,
PCI_REGION_MEM );
+
+#if defined(CONFIG_PCI_SYS_MEM_BUS) && defined(CONFIG_PCI_SYS_MEM_PHYS) && \
+ defined(CONFIG_PCI_SYS_MEM_SIZE)
+ /* System memory space */
+ pci_set_region(hose->regions + reg_num++,
+ CONFIG_PCI_SYS_MEM_BUS,
+ CONFIG_PCI_SYS_MEM_PHYS,
+ CONFIG_PCI_SYS_MEM_SIZE,
+ PCI_REGION_MEM | PCI_REGION_MEMORY );
+#endif
+
hose->region_count = reg_num;
pci_setup_indirect(hose, PCIX0_CFGADR, PCIX0_CFGDATA);
@@ -502,7 +514,7 @@
out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */
#endif
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
out32r( PCIX0_BRDGOPT1, 0x04000060 ); /* PLB Rq pri highest */
out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1 */
#elif defined(PCIX0_BRDGOPT1)
@@ -520,8 +532,13 @@
out32r( PCIX0_POM0SA, 0 ); /* disable */
out32r( PCIX0_POM1SA, 0 ); /* disable */
out32r( PCIX0_POM2SA, 0 ); /* disable */
+#if defined(CONFIG_440SPE)
+ out32r( PCIX0_POM0LAL, 0x10000000 );
+ out32r( PCIX0_POM0LAH, 0x0000000c );
+#else
out32r( PCIX0_POM0LAL, 0x00000000 );
out32r( PCIX0_POM0LAH, 0x00000003 );
+#endif
out32r( PCIX0_POM0PCIAL, CFG_PCI_MEMBASE );
out32r( PCIX0_POM0PCIAH, 0x00000000 );
out32r( PCIX0_POM0SA, 0xf0000001 ); /* 256MB, enabled */
@@ -545,10 +562,12 @@
}
}
-
void pci_init_board(void)
{
pci_440_init (&ppc440_hose);
+#if defined(CONFIG_440SPE)
+ pcie_setup_hoses();
+#endif
}
#endif /* CONFIG_440 & CONFIG_PCI */
diff --git a/cpu/ppc4xx/440spe_pcie.c b/cpu/ppc4xx/440spe_pcie.c
new file mode 100644
index 0000000..2e920aa
--- /dev/null
+++ b/cpu/ppc4xx/440spe_pcie.c
@@ -0,0 +1,592 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Roland Dreier <rolandd@cisco.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <asm/processor.h>
+#include <asm-ppc/io.h>
+#include <ppc4xx.h>
+#include <common.h>
+#include <pci.h>
+
+#include "440spe_pcie.h"
+
+#if defined(CONFIG_440SPE)
+#if defined(CONFIG_PCI)
+
+enum {
+ PTYPE_ENDPOINT = 0x0,
+ PTYPE_LEGACY_ENDPOINT = 0x1,
+ PTYPE_ROOT_PORT = 0x4,
+
+ LNKW_X1 = 0x1,
+ LNKW_X4 = 0x4,
+ LNKW_X8 = 0x8
+};
+
+static int pcie_read_config(struct pci_controller *hose, unsigned int devfn,
+ int offset, int len, u32 *val) {
+
+ *val = 0;
+ /*
+ * 440SPE implements only one function per port
+ */
+ if (!((PCI_FUNC(devfn) == 0) && (PCI_DEV(devfn) == 1)))
+ return 0;
+
+ devfn = PCI_BDF(0,0,0);
+ offset += devfn << 4;
+
+ switch (len) {
+ case 1:
+ *val = in_8(hose->cfg_data + offset);
+ break;
+ case 2:
+ *val = in_le16((u16 *)(hose->cfg_data + offset));
+ break;
+ default:
+ *val = in_le32((u32 *)(hose->cfg_data + offset));
+ break;
+ }
+ return 0;
+}
+
+static int pcie_write_config(struct pci_controller *hose, unsigned int devfn,
+ int offset, int len, u32 val) {
+
+ /*
+ * 440SPE implements only one function per port
+ */
+ if (!((PCI_FUNC(devfn) == 0) && (PCI_DEV(devfn) == 1)))
+ return 0;
+
+ devfn = PCI_BDF(0,0,0);
+ offset += devfn << 4;
+
+ switch (len) {
+ case 1:
+ out_8(hose->cfg_data + offset, val);
+ break;
+ case 2:
+ out_le16((u16 *)(hose->cfg_data + offset), val);
+ break;
+ default:
+ out_le32((u32 *)(hose->cfg_data + offset), val);
+ break;
+ }
+ return 0;
+}
+
+int pcie_read_config_byte(struct pci_controller *hose,pci_dev_t dev,int offset,u8 *val)
+{
+ u32 v;
+ int rv;
+
+ rv = pcie_read_config(hose, dev, offset, 1, &v);
+ *val = (u8)v;
+ return rv;
+}
+
+int pcie_read_config_word(struct pci_controller *hose,pci_dev_t dev,int offset,u16 *val)
+{
+ u32 v;
+ int rv;
+
+ rv = pcie_read_config(hose, dev, offset, 2, &v);
+ *val = (u16)v;
+ return rv;
+}
+
+int pcie_read_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset,u32 *val)
+{
+ u32 v;
+ int rv;
+
+ rv = pcie_read_config(hose, dev, offset, 3, &v);
+ *val = (u32)v;
+ return rv;
+}
+
+int pcie_write_config_byte(struct pci_controller *hose,pci_dev_t dev,int offset,u8 val)
+{
+ return pcie_write_config(hose,(u32)dev,offset,1,val);
+}
+
+int pcie_write_config_word(struct pci_controller *hose,pci_dev_t dev,int offset,u16 val)
+{
+ return pcie_write_config(hose,(u32)dev,offset,2,(u32 )val);
+}
+
+int pcie_write_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset,u32 val)
+{
+ return pcie_write_config(hose,(u32)dev,offset,3,(u32 )val);
+}
+
+static void ppc440spe_setup_utl(u32 port) {
+
+ volatile void *utl_base = NULL;
+
+ /*
+ * Map UTL registers
+ */
+ switch (port) {
+ case 0:
+ mtdcr(DCRN_PEGPL_REGBAH(PCIE0), 0x0000000c);
+ mtdcr(DCRN_PEGPL_REGBAL(PCIE0), 0x20000000);
+ mtdcr(DCRN_PEGPL_REGMSK(PCIE0), 0x00007001);
+ mtdcr(DCRN_PEGPL_SPECIAL(PCIE0), 0x68782800);
+ break;
+
+ case 1:
+ mtdcr(DCRN_PEGPL_REGBAH(PCIE1), 0x0000000c);
+ mtdcr(DCRN_PEGPL_REGBAL(PCIE1), 0x20001000);
+ mtdcr(DCRN_PEGPL_REGMSK(PCIE1), 0x00007001);
+ mtdcr(DCRN_PEGPL_SPECIAL(PCIE1), 0x68782800);
+ break;
+
+ case 2:
+ mtdcr(DCRN_PEGPL_REGBAH(PCIE2), 0x0000000c);
+ mtdcr(DCRN_PEGPL_REGBAL(PCIE2), 0x20002000);
+ mtdcr(DCRN_PEGPL_REGMSK(PCIE2), 0x00007001);
+ mtdcr(DCRN_PEGPL_SPECIAL(PCIE2), 0x68782800);
+ break;
+ }
+ utl_base = (unsigned int *)(CFG_PCIE_BASE + 0x1000 * port);
+
+ /*
+ * Set buffer allocations and then assert VRB and TXE.
+ */
+ out_be32(utl_base + PEUTL_OUTTR, 0x08000000);
+ out_be32(utl_base + PEUTL_INTR, 0x02000000);
+ out_be32(utl_base + PEUTL_OPDBSZ, 0x10000000);
+ out_be32(utl_base + PEUTL_PBBSZ, 0x53000000);
+ out_be32(utl_base + PEUTL_IPHBSZ, 0x08000000);
+ out_be32(utl_base + PEUTL_IPDBSZ, 0x10000000);
+ out_be32(utl_base + PEUTL_RCIRQEN, 0x00f00000);
+ out_be32(utl_base + PEUTL_PCTL, 0x80800066);
+}
+
+static int check_error(void)
+{
+ u32 valPE0, valPE1, valPE2;
+ int err = 0;
+
+ /* SDR0_PEGPLLLCT1 reset */
+ if (!(valPE0 = SDR_READ(PESDR0_PLLLCT1) & 0x01000000)) {
+ printf("PCIE: SDR0_PEGPLLLCT1 reset error 0x%x\n", valPE0);
+ }
+
+ valPE0 = SDR_READ(PESDR0_RCSSET);
+ valPE1 = SDR_READ(PESDR1_RCSSET);
+ valPE2 = SDR_READ(PESDR2_RCSSET);
+
+ /* SDR0_PExRCSSET rstgu */
+ if (!(valPE0 & 0x01000000) ||
+ !(valPE1 & 0x01000000) ||
+ !(valPE2 & 0x01000000)) {
+ printf("PCIE: SDR0_PExRCSSET rstgu error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET rstdl */
+ if (!(valPE0 & 0x00010000) ||
+ !(valPE1 & 0x00010000) ||
+ !(valPE2 & 0x00010000)) {
+ printf("PCIE: SDR0_PExRCSSET rstdl error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET rstpyn */
+ if ((valPE0 & 0x00001000) ||
+ (valPE1 & 0x00001000) ||
+ (valPE2 & 0x00001000)) {
+ printf("PCIE: SDR0_PExRCSSET rstpyn error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET hldplb */
+ if ((valPE0 & 0x10000000) ||
+ (valPE1 & 0x10000000) ||
+ (valPE2 & 0x10000000)) {
+ printf("PCIE: SDR0_PExRCSSET hldplb error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET rdy */
+ if ((valPE0 & 0x00100000) ||
+ (valPE1 & 0x00100000) ||
+ (valPE2 & 0x00100000)) {
+ printf("PCIE: SDR0_PExRCSSET rdy error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET shutdown */
+ if ((valPE0 & 0x00000100) ||
+ (valPE1 & 0x00000100) ||
+ (valPE2 & 0x00000100)) {
+ printf("PCIE: SDR0_PExRCSSET shutdown error\n");
+ err = -1;
+ }
+ return err;
+}
+
+/*
+ * Initialize PCI Express core
+ */
+int ppc440spe_init_pcie(void)
+{
+ int time_out = 20;
+
+ /* Set PLL clock receiver to LVPECL */
+ SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) | 1 << 28);
+
+ if (check_error())
+ return -1;
+
+ if (!(SDR_READ(PESDR0_PLLLCT2) & 0x10000))
+ {
+ printf("PCIE: PESDR_PLLCT2 resistance calibration failed (0x%08x)\n",
+ SDR_READ(PESDR0_PLLLCT2));
+ return -1;
+ }
+ /* De-assert reset of PCIe PLL, wait for lock */
+ SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) & ~(1 << 24));
+ udelay(3);
+
+ while(time_out) {
+ if (!(SDR_READ(PESDR0_PLLLCT3) & 0x10000000)) {
+ time_out--;
+ udelay(1);
+ } else
+ break;
+ }
+ if (!time_out) {
+ printf("PCIE: VCO output not locked\n");
+ return -1;
+ }
+ return 0;
+}
+
+int ppc440spe_init_pcie_rootport(int port)
+{
+ static int core_init;
+ volatile u32 val = 0;
+ int attempts;
+
+ if (!core_init) {
+ ++core_init;
+ if (ppc440spe_init_pcie())
+ return -1;
+ }
+
+ /*
+ * Initialize various parts of the PCI Express core for our port:
+ *
+ * - Set as a root port and enable max width
+ * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4).
+ * - Set up UTL configuration.
+ * - Increase SERDES drive strength to levels suggested by AMCC.
+ * - De-assert RSTPYN, RSTDL and RSTGU.
+ *
+ * NOTICE for revB chip: PESDRn_UTLSET2 is not set - we leave it with
+ * default setting 0x11310000. The register has new fields,
+ * PESDRn_UTLSET2[LKINE] in particular: clearing it leads to PCIE core
+ * hang.
+ */
+ switch (port) {
+ case 0:
+ SDR_WRITE(PESDR0_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X8 << 12);
+
+ SDR_WRITE(PESDR0_UTLSET1, 0x21222222);
+ if (!ppc440spe_revB())
+ SDR_WRITE(PESDR0_UTLSET2, 0x11000000);
+ SDR_WRITE(PESDR0_HSSL0SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL1SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL2SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL3SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000);
+ SDR_WRITE(PESDR0_RCSSET,
+ (SDR_READ(PESDR0_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12);
+ break;
+
+ case 1:
+ SDR_WRITE(PESDR1_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12);
+ SDR_WRITE(PESDR1_UTLSET1, 0x21222222);
+ if (!ppc440spe_revB())
+ SDR_WRITE(PESDR1_UTLSET2, 0x11000000);
+ SDR_WRITE(PESDR1_HSSL0SET1, 0x35000000);
+ SDR_WRITE(PESDR1_HSSL1SET1, 0x35000000);
+ SDR_WRITE(PESDR1_HSSL2SET1, 0x35000000);
+ SDR_WRITE(PESDR1_HSSL3SET1, 0x35000000);
+ SDR_WRITE(PESDR1_RCSSET,
+ (SDR_READ(PESDR1_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12);
+ break;
+
+ case 2:
+ SDR_WRITE(PESDR2_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12);
+ SDR_WRITE(PESDR2_UTLSET1, 0x21222222);
+ if (!ppc440spe_revB())
+ SDR_WRITE(PESDR2_UTLSET2, 0x11000000);
+ SDR_WRITE(PESDR2_HSSL0SET1, 0x35000000);
+ SDR_WRITE(PESDR2_HSSL1SET1, 0x35000000);
+ SDR_WRITE(PESDR2_HSSL2SET1, 0x35000000);
+ SDR_WRITE(PESDR2_HSSL3SET1, 0x35000000);
+ SDR_WRITE(PESDR2_RCSSET,
+ (SDR_READ(PESDR2_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12);
+ break;
+ }
+ /*
+ * Notice: the following delay has critical impact on device
+ * initialization - if too short (<50ms) the link doesn't get up.
+ */
+ mdelay(100);
+
+ switch (port) {
+ case 0: val = SDR_READ(PESDR0_RCSSTS); break;
+ case 1: val = SDR_READ(PESDR1_RCSSTS); break;
+ case 2: val = SDR_READ(PESDR2_RCSSTS); break;
+ }
+
+ if (val & (1 << 20)) {
+ printf("PCIE%d: PGRST failed %08x\n", port, val);
+ return -1;
+ }
+
+ /*
+ * Verify link is up
+ */
+ val = 0;
+ switch (port)
+ {
+ case 0:
+ val = SDR_READ(PESDR0_LOOP);
+ break;
+ case 1:
+ val = SDR_READ(PESDR1_LOOP);
+ break;
+ case 2:
+ val = SDR_READ(PESDR2_LOOP);
+ break;
+ }
+ if (!(val & 0x00001000)) {
+ printf("PCIE%d: link is not up.\n", port);
+ return -1;
+ }
+
+ /*
+ * Setup UTL registers - but only on revA!
+ * We use default settings for revB chip.
+ */
+ if (!ppc440spe_revB())
+ ppc440spe_setup_utl(port);
+
+ /*
+ * We map PCI Express configuration access into the 512MB regions
+ *
+ * NOTICE: revB is very strict about PLB real addressess and ranges to
+ * be mapped for config space; it seems to only work with d_nnnn_nnnn
+ * range (hangs the core upon config transaction attempts when set
+ * otherwise) while revA uses c_nnnn_nnnn.
+ *
+ * For revA:
+ * PCIE0: 0xc_4000_0000
+ * PCIE1: 0xc_8000_0000
+ * PCIE2: 0xc_c000_0000
+ *
+ * For revB:
+ * PCIE0: 0xd_0000_0000
+ * PCIE1: 0xd_2000_0000
+ * PCIE2: 0xd_4000_0000
+ */
+
+ switch (port) {
+ case 0:
+ if (ppc440spe_revB()) {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000d);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x00000000);
+ } else {
+ /* revA */
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000c);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x40000000);
+ }
+ mtdcr(DCRN_PEGPL_CFGMSK(PCIE0), 0xe0000001); /* 512MB region, valid */
+ break;
+
+ case 1:
+ if (ppc440spe_revB()) {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000d);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x20000000);
+ } else {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000c);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x80000000);
+ }
+ mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */
+ break;
+
+ case 2:
+ if (ppc440spe_revB()) {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000d);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0x40000000);
+ } else {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000c);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0xc0000000);
+ }
+ mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */
+ break;
+ }
+
+ /*
+ * Check for VC0 active and assert RDY.
+ */
+ attempts = 10;
+ switch (port) {
+ case 0:
+ while(!(SDR_READ(PESDR0_RCSSTS) & (1 << 16))) {
+ if (!(attempts--)) {
+ printf("PCIE0: VC0 not active\n");
+ return -1;
+ }
+ mdelay(1000);
+ }
+ SDR_WRITE(PESDR0_RCSSET, SDR_READ(PESDR0_RCSSET) | 1 << 20);
+ break;
+ case 1:
+ while(!(SDR_READ(PESDR1_RCSSTS) & (1 << 16))) {
+ if (!(attempts--)) {
+ printf("PCIE1: VC0 not active\n");
+ return -1;
+ }
+ mdelay(1000);
+ }
+
+ SDR_WRITE(PESDR1_RCSSET, SDR_READ(PESDR1_RCSSET) | 1 << 20);
+ break;
+ case 2:
+ while(!(SDR_READ(PESDR2_RCSSTS) & (1 << 16))) {
+ if (!(attempts--)) {
+ printf("PCIE2: VC0 not active\n");
+ return -1;
+ }
+ mdelay(1000);
+ }
+
+ SDR_WRITE(PESDR2_RCSSET, SDR_READ(PESDR2_RCSSET) | 1 << 20);
+ break;
+ }
+ mdelay(100);
+
+ return 0;
+}
+
+void ppc440spe_setup_pcie(struct pci_controller *hose, int port)
+{
+ volatile void *mbase = NULL;
+
+ pci_set_ops(hose,
+ pcie_read_config_byte,
+ pcie_read_config_word,
+ pcie_read_config_dword,
+ pcie_write_config_byte,
+ pcie_write_config_word,
+ pcie_write_config_dword);
+
+ switch(port) {
+ case 0:
+ mbase = (u32 *)CFG_PCIE0_XCFGBASE;
+ hose->cfg_data = (u8 *)CFG_PCIE0_CFGBASE;
+ break;
+ case 1:
+ mbase = (u32 *)CFG_PCIE1_XCFGBASE;
+ hose->cfg_data = (u8 *)CFG_PCIE1_CFGBASE;
+ break;
+ case 2:
+ mbase = (u32 *)CFG_PCIE2_XCFGBASE;
+ hose->cfg_data = (u8 *)CFG_PCIE2_CFGBASE;
+ break;
+ }
+
+ /*
+ * Set bus numbers on our root port
+ */
+ if (ppc440spe_revB()) {
+ out_8((u8 *)mbase + PCI_PRIMARY_BUS, 0);
+ out_8((u8 *)mbase + PCI_SECONDARY_BUS, 1);
+ out_8((u8 *)mbase + PCI_SUBORDINATE_BUS, 1);
+ } else {
+ out_8((u8 *)mbase + PCI_PRIMARY_BUS, 0);
+ out_8((u8 *)mbase + PCI_SECONDARY_BUS, 0);
+ }
+
+ /*
+ * Set up outbound translation to hose->mem_space from PLB
+ * addresses at an offset of 0xd_0000_0000. We set the low
+ * bits of the mask to 11 to turn off splitting into 8
+ * subregions and to enable the outbound translation.
+ */
+ out_le32(mbase + PECFG_POM0LAH, 0x00000000);
+ out_le32(mbase + PECFG_POM0LAL, (CFG_PCIE_MEMBASE +
+ port * CFG_PCIE_MEMSIZE));
+
+ switch (port) {
+ case 0:
+ mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d);
+ mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE +
+ port * CFG_PCIE_MEMSIZE);
+ mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff);
+ mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0),
+ ~(CFG_PCIE_MEMSIZE - 1) | 3);
+ break;
+ case 1:
+ mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d);
+ mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), (CFG_PCIE_MEMBASE +
+ port * CFG_PCIE_MEMSIZE));
+ mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff);
+ mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1),
+ ~(CFG_PCIE_MEMSIZE - 1) | 3);
+ break;
+ case 2:
+ mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d);
+ mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), (CFG_PCIE_MEMBASE +
+ port * CFG_PCIE_MEMSIZE));
+ mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff);
+ mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2),
+ ~(CFG_PCIE_MEMSIZE - 1) | 3);
+ break;
+ }
+
+ /* Set up 16GB inbound memory window at 0 */
+ out_le32(mbase + PCI_BASE_ADDRESS_0, 0);
+ out_le32(mbase + PCI_BASE_ADDRESS_1, 0);
+ out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffc);
+ out_le32(mbase + PECFG_BAR0LMPA, 0);
+ out_le32(mbase + PECFG_PIM0LAL, 0);
+ out_le32(mbase + PECFG_PIM0LAH, 0);
+ out_le32(mbase + PECFG_PIMEN, 0x1);
+
+ /* Enable I/O, Mem, and Busmaster cycles */
+ out_le16((u16 *)(mbase + PCI_COMMAND),
+ in_le16((u16 *)(mbase + PCI_COMMAND)) |
+ PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+}
+#endif /* CONFIG_PCI */
+#endif /* CONFIG_440SPE */
diff --git a/cpu/ppc4xx/440spe_pcie.h b/cpu/ppc4xx/440spe_pcie.h
new file mode 100644
index 0000000..47df762
--- /dev/null
+++ b/cpu/ppc4xx/440spe_pcie.h
@@ -0,0 +1,162 @@
+/*
+ * Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Roland Dreier <rolandd@cisco.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <ppc4xx.h>
+#ifndef __440SPE_PCIE_H
+#define __440SPE_PCIE_H
+
+#define mdelay(n) ({unsigned long __ms=(n); while (__ms--) udelay(1000);})
+
+#define DCRN_SDR0_CFGADDR 0x00e
+#define DCRN_SDR0_CFGDATA 0x00f
+
+#define DCRN_PCIE0_BASE 0x100
+#define DCRN_PCIE1_BASE 0x120
+#define DCRN_PCIE2_BASE 0x140
+#define PCIE0 DCRN_PCIE0_BASE
+#define PCIE1 DCRN_PCIE1_BASE
+#define PCIE2 DCRN_PCIE2_BASE
+
+#define DCRN_PEGPL_CFGBAH(base) (base + 0x00)
+#define DCRN_PEGPL_CFGBAL(base) (base + 0x01)
+#define DCRN_PEGPL_CFGMSK(base) (base + 0x02)
+#define DCRN_PEGPL_MSGBAH(base) (base + 0x03)
+#define DCRN_PEGPL_MSGBAL(base) (base + 0x04)
+#define DCRN_PEGPL_MSGMSK(base) (base + 0x05)
+#define DCRN_PEGPL_OMR1BAH(base) (base + 0x06)
+#define DCRN_PEGPL_OMR1BAL(base) (base + 0x07)
+#define DCRN_PEGPL_OMR1MSKH(base) (base + 0x08)
+#define DCRN_PEGPL_OMR1MSKL(base) (base + 0x09)
+#define DCRN_PEGPL_REGBAH(base) (base + 0x12)
+#define DCRN_PEGPL_REGBAL(base) (base + 0x13)
+#define DCRN_PEGPL_REGMSK(base) (base + 0x14)
+#define DCRN_PEGPL_SPECIAL(base) (base + 0x15)
+
+/*
+ * System DCRs (SDRs)
+ */
+#define PESDR0_PLLLCT1 0x03a0
+#define PESDR0_PLLLCT2 0x03a1
+#define PESDR0_PLLLCT3 0x03a2
+
+#define PESDR0_UTLSET1 0x0300
+#define PESDR0_UTLSET2 0x0301
+#define PESDR0_DLPSET 0x0302
+#define PESDR0_LOOP 0x0303
+#define PESDR0_RCSSET 0x0304
+#define PESDR0_RCSSTS 0x0305
+#define PESDR0_HSSL0SET1 0x0306
+#define PESDR0_HSSL0SET2 0x0307
+#define PESDR0_HSSL0STS 0x0308
+#define PESDR0_HSSL1SET1 0x0309
+#define PESDR0_HSSL1SET2 0x030a
+#define PESDR0_HSSL1STS 0x030b
+#define PESDR0_HSSL2SET1 0x030c
+#define PESDR0_HSSL2SET2 0x030d
+#define PESDR0_HSSL2STS 0x030e
+#define PESDR0_HSSL3SET1 0x030f
+#define PESDR0_HSSL3SET2 0x0310
+#define PESDR0_HSSL3STS 0x0311
+#define PESDR0_HSSL4SET1 0x0312
+#define PESDR0_HSSL4SET2 0x0313
+#define PESDR0_HSSL4STS 0x0314
+#define PESDR0_HSSL5SET1 0x0315
+#define PESDR0_HSSL5SET2 0x0316
+#define PESDR0_HSSL5STS 0x0317
+#define PESDR0_HSSL6SET1 0x0318
+#define PESDR0_HSSL6SET2 0x0319
+#define PESDR0_HSSL6STS 0x031a
+#define PESDR0_HSSL7SET1 0x031b
+#define PESDR0_HSSL7SET2 0x031c
+#define PESDR0_HSSL7STS 0x031d
+#define PESDR0_HSSCTLSET 0x031e
+#define PESDR0_LANE_ABCD 0x031f
+#define PESDR0_LANE_EFGH 0x0320
+
+#define PESDR1_UTLSET1 0x0340
+#define PESDR1_UTLSET2 0x0341
+#define PESDR1_DLPSET 0x0342
+#define PESDR1_LOOP 0x0343
+#define PESDR1_RCSSET 0x0344
+#define PESDR1_RCSSTS 0x0345
+#define PESDR1_HSSL0SET1 0x0346
+#define PESDR1_HSSL0SET2 0x0347
+#define PESDR1_HSSL0STS 0x0348
+#define PESDR1_HSSL1SET1 0x0349
+#define PESDR1_HSSL1SET2 0x034a
+#define PESDR1_HSSL1STS 0x034b
+#define PESDR1_HSSL2SET1 0x034c
+#define PESDR1_HSSL2SET2 0x034d
+#define PESDR1_HSSL2STS 0x034e
+#define PESDR1_HSSL3SET1 0x034f
+#define PESDR1_HSSL3SET2 0x0350
+#define PESDR1_HSSL3STS 0x0351
+#define PESDR1_HSSCTLSET 0x0352
+#define PESDR1_LANE_ABCD 0x0353
+
+#define PESDR2_UTLSET1 0x0370
+#define PESDR2_UTLSET2 0x0371
+#define PESDR2_DLPSET 0x0372
+#define PESDR2_LOOP 0x0373
+#define PESDR2_RCSSET 0x0374
+#define PESDR2_RCSSTS 0x0375
+#define PESDR2_HSSL0SET1 0x0376
+#define PESDR2_HSSL0SET2 0x0377
+#define PESDR2_HSSL0STS 0x0378
+#define PESDR2_HSSL1SET1 0x0379
+#define PESDR2_HSSL1SET2 0x037a
+#define PESDR2_HSSL1STS 0x037b
+#define PESDR2_HSSL2SET1 0x037c
+#define PESDR2_HSSL2SET2 0x037d
+#define PESDR2_HSSL2STS 0x037e
+#define PESDR2_HSSL3SET1 0x037f
+#define PESDR2_HSSL3SET2 0x0380
+#define PESDR2_HSSL3STS 0x0381
+#define PESDR2_HSSCTLSET 0x0382
+#define PESDR2_LANE_ABCD 0x0383
+
+/*
+ * UTL register offsets
+ */
+#define PEUTL_PBBSZ 0x20
+#define PEUTL_OPDBSZ 0x68
+#define PEUTL_IPHBSZ 0x70
+#define PEUTL_IPDBSZ 0x78
+#define PEUTL_OUTTR 0x90
+#define PEUTL_INTR 0x98
+#define PEUTL_PCTL 0xa0
+#define PEUTL_RCIRQEN 0xb8
+
+/*
+ * Config space register offsets
+ */
+#define PECFG_BAR0LMPA 0x210
+#define PECFG_BAR0HMPA 0x214
+#define PECFG_PIMEN 0x33c
+#define PECFG_PIM0LAL 0x340
+#define PECFG_PIM0LAH 0x344
+#define PECFG_POM0LAL 0x380
+#define PECFG_POM0LAH 0x384
+
+#define SDR_READ(offset) ({\
+ mtdcr(DCRN_SDR0_CFGADDR, offset); \
+ mfdcr(DCRN_SDR0_CFGDATA);})
+
+#define SDR_WRITE(offset, data) ({\
+ mtdcr(DCRN_SDR0_CFGADDR, offset); \
+ mtdcr(DCRN_SDR0_CFGDATA,data);})
+
+int ppc440spe_init_pcie(void);
+int ppc440spe_init_pcie_rootport(int port);
+void yucca_setup_pcie_fpga_rootpoint(int port);
+void ppc440spe_setup_pcie(struct pci_controller *hose, int port);
+int yucca_pcie_card_present(int port);
+int pcie_hose_scan(struct pci_controller *hose, int bus);
+#endif /* __440SPE_PCIE_H */
diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c
index 86dc2d0..fab65af 100644
--- a/cpu/ppc4xx/4xx_enet.c
+++ b/cpu/ppc4xx/4xx_enet.c
@@ -181,6 +181,9 @@
{
EMAC_4XX_HW_PST hw_p = dev->priv;
uint32_t failsafe = 10000;
+#if defined(CONFIG_440SPE)
+ unsigned long mfr;
+#endif
out32 (EMAC_IER + hw_p->hw_addr, 0x00000000); /* disable emac interrupts */
@@ -202,8 +205,23 @@
}
/* EMAC RESET */
+#if defined(CONFIG_440SPE)
+ /* provide clocks for EMAC internal loopback */
+ mfsdr (sdr_mfr, mfr);
+ mfr |= 0x08000000;
+ mtsdr(sdr_mfr, mfr);
+#endif
+
out32 (EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
+#if defined(CONFIG_440SPE)
+ /* remove clocks for EMAC internal loopback */
+ mfsdr (sdr_mfr, mfr);
+ mfr &= ~0x08000000;
+ mtsdr(sdr_mfr, mfr);
+#endif
+
+
#ifndef CONFIG_NETCONSOLE
hw_p->print_speed = 1; /* print speed message again next time */
#endif
@@ -301,7 +319,7 @@
return ((int)pfc1);
}
-#endif
+#endif /* CONFIG_440_GX */
static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
{
@@ -314,12 +332,16 @@
unsigned mode_reg;
unsigned short devnum;
unsigned short reg_short;
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
sys_info_t sysinfo;
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
int ethgroup = -1;
#endif
#endif
+#if defined(CONFIG_440SPE)
+ unsigned long mfr;
+#endif
+
EMAC_4XX_HW_PST hw_p = dev->priv;
@@ -330,7 +352,7 @@
return -1;
}
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
/* Need to get the OPB frequency so we can access the PHY */
get_sys_info (&sysinfo);
#endif
@@ -360,6 +382,7 @@
hw_p->stats.pkts_tx = 0;
hw_p->stats.pkts_rx = 0;
hw_p->stats.pkts_handled = 0;
+ hw_p->print_speed = 1; /* print speed message again next time */
#endif
hw_p->tx_err_index = 0; /* Transmit Error Index for tx_err_log */
@@ -373,7 +396,7 @@
hw_p->tx_i_index = 0; /* Transmit Interrupt Queue Index */
hw_p->tx_u_index = 0; /* Transmit User Queue Index */
-#if defined(CONFIG_440) && !defined(CONFIG_440SP)
+#if defined(CONFIG_440) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)
/* set RMII mode */
/* NOTE: 440GX spec states that mode is mutually exclusive */
/* NOTE: Therefore, disable all other EMACS, since we handle */
@@ -406,6 +429,12 @@
__asm__ volatile ("eieio");
/* reset emac so we have access to the phy */
+#if defined(CONFIG_440SPE)
+ /* provide clocks for EMAC internal loopback */
+ mfsdr (sdr_mfr, mfr);
+ mfr |= 0x08000000;
+ mtsdr(sdr_mfr, mfr);
+#endif
out32 (EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
__asm__ volatile ("eieio");
@@ -416,7 +445,14 @@
failsafe--;
}
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440SPE)
+ /* remove clocks for EMAC internal loopback */
+ mfsdr (sdr_mfr, mfr);
+ mfr &= ~0x08000000;
+ mtsdr(sdr_mfr, mfr);
+#endif
+
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
/* Whack the M1 register */
mode_reg = 0x0;
mode_reg &= ~0x00000038;
@@ -468,7 +504,7 @@
if (hw_p->first_init == 0) {
miiphy_reset (dev->name, reg);
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
#if defined(CONFIG_CIS8201_PHY)
/*
* Cicada 8201 PHY needs to have an extended register whacked
@@ -544,7 +580,7 @@
(int) speed, (duplex == HALF) ? "HALF" : "FULL");
}
-#if defined(CONFIG_440) && !defined(CONFIG_440SP)
+#if defined(CONFIG_440) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)
#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
mfsdr(sdr_mfr, reg);
if (speed == 100) {
@@ -575,7 +611,7 @@
#endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */
/* set the Mal configuration reg */
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
mtdcr (malmcr, MAL_CR_PLBB | MAL_CR_OPBBL | MAL_CR_LEA |
MAL_CR_PLBLT_DEFAULT | MAL_CR_EOPIE | 0x00330000);
#else
@@ -759,8 +795,7 @@
/* set speed */
if (speed == _1000BASET) {
-#if defined(CONFIG_440SP)
-#define SDR0_PFC1_EM_1000 0x00200000
+#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
unsigned long pfc1;
mfsdr (sdr_pfc1, pfc1);
pfc1 |= SDR0_PFC1_EM_1000;
@@ -787,7 +822,7 @@
/* set receive low/high water mark register */
#if defined(CONFIG_440)
- /* 440GP has a 64 byte burst length */
+ /* 440s has a 64 byte burst length */
out32 (EMAC_RX_HI_LO_WMARK + hw_p->hw_addr, 0x80009000);
#else
/* 405s have a 16 byte burst length */
@@ -895,7 +930,7 @@
#if defined (CONFIG_440)
-#if defined(CONFIG_440SP)
+#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
/*
* Hack: On 440SP all enet irq sources are located on UIC1
* Needs some cleanup. --sr
@@ -1367,21 +1402,20 @@
#endif
/* set phy num and mode */
bis->bi_phynum[0] = CONFIG_PHY_ADDR;
+ bis->bi_phymode[0] = 0;
+
#if defined(CONFIG_PHY1_ADDR)
bis->bi_phynum[1] = CONFIG_PHY1_ADDR;
+ bis->bi_phymode[1] = 0;
#endif
#if defined(CONFIG_440GX)
bis->bi_phynum[2] = CONFIG_PHY2_ADDR;
bis->bi_phynum[3] = CONFIG_PHY3_ADDR;
- bis->bi_phymode[0] = 0;
- bis->bi_phymode[1] = 0;
bis->bi_phymode[2] = 2;
bis->bi_phymode[3] = 2;
-#if defined (CONFIG_440GX)
ppc_4xx_eth_setup_bridge(0, bis);
#endif
-#endif
for (eth_num = 0; eth_num < LAST_EMAC_NUM; eth_num++) {
@@ -1478,9 +1512,15 @@
if (0 == virgin) {
/* set the MAL IER ??? names may change with new spec ??? */
+#if defined(CONFIG_440SPE)
+ mal_ier =
+ MAL_IER_PT | MAL_IER_PRE | MAL_IER_PWE |
+ MAL_IER_DE | MAL_IER_OTE | MAL_IER_OE | MAL_IER_PE ;
+#else
mal_ier =
MAL_IER_DE | MAL_IER_NE | MAL_IER_TE |
MAL_IER_OPBE | MAL_IER_PLBE;
+#endif
mtdcr (malesr, 0xffffffff); /* clear pending interrupts */
mtdcr (maltxdeir, 0xffffffff); /* clear pending interrupts */
mtdcr (malrxdeir, 0xffffffff); /* clear pending interrupts */
@@ -1510,11 +1550,13 @@
#else
emac0_dev = dev;
#endif
+
+#if defined(CONFIG_NET_MULTI)
#if defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII)
miiphy_register (dev->name,
emac4xx_miiphy_read, emac4xx_miiphy_write);
#endif
-
+#endif
} /* end for each supported device */
return (1);
}
diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile
index c563457..7d6990f 100644
--- a/cpu/ppc4xx/Makefile
+++ b/cpu/ppc4xx/Makefile
@@ -31,7 +31,8 @@
bedbug_405.o commproc.o \
cpu.o cpu_init.o i2c.o interrupts.o \
miiphy.o sdram.o serial.o \
- spd_sdram.o speed.o traps.o usb_ohci.o usbdev.o
+ spd_sdram.o speed.o traps.o usb_ohci.o usbdev.o \
+ 440spe_pcie.o
OBJS = $(AOBJS) $(COBJS)
diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c
index d9b5d32..bc51fbf 100644
--- a/cpu/ppc4xx/cpu.c
+++ b/cpu/ppc4xx/cpu.c
@@ -82,7 +82,9 @@
return (mfdcr(cpc0_strp1) & CPC0_STRP1_PAE_MASK);
#endif
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+ defined(CONFIG_440SPE)
unsigned long val;
mfsdr(sdr_sdstp1, val);
@@ -91,8 +93,8 @@
}
#endif
-#if defined(CONFIG_405EP)|| defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_405EP) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
+ defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
#define I2C_BOOTROM
@@ -102,7 +104,9 @@
return (mfdcr(cpc0_boot) & CPC0_BOOT_SEP);
#endif
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+ defined(CONFIG_440SPE)
unsigned long val;
mfsdr(sdr_sdcs, val);
@@ -248,6 +252,14 @@
puts("SP Rev. B");
break;
+ case PVR_440SPe_RA:
+ puts("SPe Rev. A");
+ break;
+
+ case PVR_440SPe_RB:
+ puts("SPe Rev. B");
+ break;
+
default:
printf (" UNKNOWN (PVR=%08x)", pvr);
break;
@@ -303,6 +315,17 @@
return 0;
}
+#if defined (CONFIG_440SPE)
+int ppc440spe_revB() {
+ unsigned int pvr;
+
+ pvr = get_pvr();
+ if (pvr == PVR_440SPe_RB)
+ return 1;
+ else
+ return 0;
+}
+#endif
/* ------------------------------------------------------------------------- */
diff --git a/cpu/ppc4xx/interrupts.c b/cpu/ppc4xx/interrupts.c
index 3aae4ce..886f405 100644
--- a/cpu/ppc4xx/interrupts.c
+++ b/cpu/ppc4xx/interrupts.c
@@ -50,18 +50,22 @@
};
static struct irq_action irq_vecs[32];
+void uic0_interrupt( void * parms); /* UIC0 handler */
#if defined(CONFIG_440)
static struct irq_action irq_vecs1[32]; /* For UIC1 */
void uic1_interrupt( void * parms); /* UIC1 handler */
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
static struct irq_action irq_vecs2[32]; /* For UIC2 */
-
-void uic0_interrupt( void * parms); /* UIC0 handler */
void uic2_interrupt( void * parms); /* UIC2 handler */
-#endif /* CONFIG_440GX */
+#endif /* CONFIG_440GX CONFIG_440SPE */
+
+#if defined(CONFIG_440SPE)
+static struct irq_action irq_vecs3[32]; /* For UIC3 */
+void uic3_interrupt( void * parms); /* UIC3 handler */
+#endif /* CONFIG_440SPE */
#endif /* CONFIG_440 */
@@ -115,11 +119,16 @@
irq_vecs1[vec].handler = NULL;
irq_vecs1[vec].arg = NULL;
irq_vecs1[vec].count = 0;
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
irq_vecs2[vec].handler = NULL;
irq_vecs2[vec].arg = NULL;
irq_vecs2[vec].count = 0;
#endif /* CONFIG_440GX */
+#if defined(CONFIG_440SPE)
+ irq_vecs3[vec].handler = NULL;
+ irq_vecs3[vec].arg = NULL;
+ irq_vecs3[vec].count = 0;
+#endif /* CONFIG_440SPE */
#endif
}
@@ -221,6 +230,34 @@
} /* external_interrupt CONFIG_440GX */
+#elif defined(CONFIG_440SPE)
+void external_interrupt(struct pt_regs *regs)
+{
+ ulong uic_msr;
+
+ /*
+ * Read masked interrupt status register to determine interrupt source
+ */
+ /* 440 SPe uses base uic register */
+ uic_msr = mfdcr(uic0msr);
+
+ if ( (UICB0_UIC1CI & uic_msr) || (UICB0_UIC1NCI & uic_msr) )
+ uic1_interrupt(0);
+
+ if ( (UICB0_UIC2CI & uic_msr) || (UICB0_UIC2NCI & uic_msr) )
+ uic2_interrupt(0);
+
+ if ( (UICB0_UIC3CI & uic_msr) || (UICB0_UIC3NCI & uic_msr) )
+ uic3_interrupt(0);
+
+ if (uic_msr & ~(UICB0_ALL))
+ uic0_interrupt(0);
+
+ mtdcr(uic0sr, uic_msr);
+
+ return;
+} /* external_interrupt CONFIG_440SPE */
+
#else
void external_interrupt(struct pt_regs *regs)
@@ -266,7 +303,7 @@
}
#endif
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
/* Handler for UIC0 interrupt */
void uic0_interrupt( void * parms)
{
@@ -357,8 +394,8 @@
}
#endif /* defined(CONFIG_440) */
-#if defined(CONFIG_440GX)
-/* Handler for UIC1 interrupt */
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
+/* Handler for UIC2 interrupt */
void uic2_interrupt( void * parms)
{
ulong uic2_msr;
@@ -384,7 +421,7 @@
(*irq_vecs2[vec].handler)(irq_vecs2[vec].arg);
} else {
mtdcr(uic2er, mfdcr(uic2er) & ~(0x80000000 >> vec));
- printf ("Masking bogus interrupt vector (uic1) 0x%x\n", vec);
+ printf ("Masking bogus interrupt vector (uic2) 0x%x\n", vec);
}
/*
@@ -402,6 +439,51 @@
}
#endif /* defined(CONFIG_440GX) */
+#if defined(CONFIG_440SPE)
+/* Handler for UIC3 interrupt */
+void uic3_interrupt( void * parms)
+{
+ ulong uic3_msr;
+ ulong msr_shift;
+ int vec;
+
+ /*
+ * Read masked interrupt status register to determine interrupt source
+ */
+ uic3_msr = mfdcr(uic3msr);
+ msr_shift = uic3_msr;
+ vec = 0;
+
+ while (msr_shift != 0) {
+ if (msr_shift & 0x80000000) {
+ /*
+ * Increment irq counter (for debug purpose only)
+ */
+ irq_vecs3[vec].count++;
+
+ if (irq_vecs3[vec].handler != NULL) {
+ /* call isr */
+ (*irq_vecs3[vec].handler)(irq_vecs3[vec].arg);
+ } else {
+ mtdcr(uic3er, mfdcr(uic3er) & ~(0x80000000 >> vec));
+ printf ("Masking bogus interrupt vector (uic3) 0x%x\n", vec);
+ }
+
+ /*
+ * After servicing the interrupt, we have to remove the status indicator.
+ */
+ mtdcr(uic3sr, (0x80000000 >> vec));
+ }
+
+ /*
+ * Shift msr to next position and increment vector
+ */
+ msr_shift <<= 1;
+ vec++;
+ }
+}
+#endif /* defined(CONFIG_440SPE) */
+
/****************************************************************************/
/*
@@ -414,7 +496,7 @@
int i = vec;
#if defined(CONFIG_440)
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
if ((vec > 31) && (vec < 64)) {
i = vec - 32;
irqa = irq_vecs1;
@@ -441,7 +523,7 @@
irqa[i].arg = arg;
#if defined(CONFIG_440)
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
if ((vec > 31) && (vec < 64))
mtdcr (uic1er, mfdcr (uic1er) | (0x80000000 >> i));
else if (vec > 63)
@@ -464,7 +546,7 @@
int i = vec;
#if defined(CONFIG_440)
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
if ((vec > 31) && (vec < 64)) {
irqa = irq_vecs1;
i = vec - 32;
@@ -485,7 +567,7 @@
#endif
#if defined(CONFIG_440)
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
if ((vec > 31) && (vec < 64))
mtdcr (uic1er, mfdcr (uic1er) & ~(0x80000000 >> i));
else if (vec > 63)
@@ -553,7 +635,7 @@
printf("\n");
#endif
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
printf ("\nUIC 2\n");
printf ("Nr Routine Arg Count\n");
@@ -566,6 +648,19 @@
printf("\n");
#endif
+#if defined(CONFIG_440SPE)
+ printf ("\nUIC 3\n");
+ printf ("Nr Routine Arg Count\n");
+
+ for (vec=0; vec<32; vec++) {
+ if (irq_vecs3[vec].handler != NULL)
+ printf ("%02d %08lx %08lx %d\n",
+ vec+63, (ulong)irq_vecs3[vec].handler,
+ (ulong)irq_vecs3[vec].arg, irq_vecs3[vec].count);
+ }
+ printf("\n");
+#endif
+
return 0;
}
#endif /* CONFIG_COMMANDS & CFG_CMD_IRQ */
diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c
index f26f2a2..aa580ed 100644
--- a/cpu/ppc4xx/miiphy.c
+++ b/cpu/ppc4xx/miiphy.c
@@ -50,7 +50,7 @@
#include <405_mal.h>
#include <miiphy.h>
-
+#undef ET_DEBUG
/***********************************************************/
/* Dump out to the screen PHY regs */
/***********************************************************/
@@ -90,6 +90,10 @@
PHY_ANLPAR_10);
miiphy_write (devname, addr, PHY_ANAR, adv);
+ miiphy_read (devname, addr, PHY_1000BTCR, &adv);
+ adv |= (0x0300);
+ miiphy_write (devname, addr, PHY_1000BTCR, adv);
+
/* Start/Restart aneg */
miiphy_read (devname, addr, PHY_BMCR, &ctl);
ctl |= (PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);
@@ -104,7 +108,7 @@
/***********************************************************/
unsigned int miiphy_getemac_offset (void)
{
-#if (defined(CONFIG_440) && !defined(CONFIG_440SP)) && defined(CONFIG_NET_MULTI)
+#if (defined(CONFIG_440) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)) && defined(CONFIG_NET_MULTI)
unsigned long zmii;
unsigned long eoffset;
@@ -155,10 +159,12 @@
i = 0;
/* see if it is ready for sec */
- while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == 0) {
+ while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == EMAC_STACR_OC_MASK) {
udelay (7);
if (i > 5) {
-#if 0
+#ifdef ET_DEBUG
+ sta_reg = in32 (EMAC_STACR + emac_reg);
+ printf ("read : EMAC_STACR=0x%0x\n", sta_reg); /* test-only */
printf ("read err 1\n");
#endif
return -1;
@@ -167,31 +173,41 @@
}
sta_reg = reg; /* reg address */
/* set clock (50Mhz) and read flags */
-#if defined(CONFIG_440GX)
- sta_reg |= EMAC_STACR_READ;
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
+#if defined(CONFIG_IBM_EMAC4_V4) /* EMAC4 V4 changed bit setting */
+ sta_reg = (sta_reg & ~EMAC_STACR_OP_MASK) | EMAC_STACR_READ;
+#else
+ sta_reg |= EMAC_STACR_READ;
+#endif
#else
sta_reg = (sta_reg | EMAC_STACR_READ) & ~EMAC_STACR_CLK_100MHZ;
#endif
-#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX)
+#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && !defined(CONFIG__440SP) && !defined(CONFIG__440SPE)
sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ;
#endif
sta_reg = sta_reg | (addr << 5); /* Phy address */
-
+ sta_reg = sta_reg | EMAC_STACR_OC_MASK; /* new IBM emac v4 */
out32 (EMAC_STACR + emac_reg, sta_reg);
-#if 0 /* test-only */
+#ifdef ET_DEBUG
printf ("a2: write: EMAC_STACR=0x%0x\n", sta_reg); /* test-only */
#endif
sta_reg = in32 (EMAC_STACR + emac_reg);
+#ifdef ET_DEBUG
+ printf ("a21: read : EMAC_STACR=0x%0x\n", sta_reg); /* test-only */
+#endif
i = 0;
- while ((sta_reg & EMAC_STACR_OC) == 0) {
+ while ((sta_reg & EMAC_STACR_OC) == EMAC_STACR_OC_MASK) {
udelay (7);
if (i > 5) {
return -1;
}
i++;
sta_reg = in32 (EMAC_STACR + emac_reg);
+#ifdef ET_DEBUG
+ printf ("a22: read : EMAC_STACR=0x%0x\n", sta_reg); /* test-only */
+#endif
}
if ((sta_reg & EMAC_STACR_PHYE) != 0) {
return -1;
@@ -219,7 +235,7 @@
/* see if it is ready for 1000 nsec */
i = 0;
- while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == 0) {
+ while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == EMAC_STACR_OC_MASK) {
if (i > 5)
return -1;
udelay (7);
@@ -228,16 +244,21 @@
sta_reg = 0;
sta_reg = reg; /* reg address */
/* set clock (50Mhz) and read flags */
-#if defined(CONFIG_440GX)
- sta_reg |= EMAC_STACR_WRITE;
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
+#if defined(CONFIG_IBM_EMAC4_V4) /* EMAC4 V4 changed bit setting */
+ sta_reg = (sta_reg & ~EMAC_STACR_OP_MASK) | EMAC_STACR_WRITE;
+#else
+ sta_reg |= EMAC_STACR_WRITE;
+#endif
#else
sta_reg = (sta_reg | EMAC_STACR_WRITE) & ~EMAC_STACR_CLK_100MHZ;
#endif
-#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX)
+#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && !defined(CONFIG__440SP) && !defined(CONFIG__440SPE)
sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ; /* Set clock frequency (PLB freq. dependend) */
#endif
- sta_reg = sta_reg | ((unsigned long) addr << 5); /* Phy address */
+ sta_reg = sta_reg | ((unsigned long) addr << 5);/* Phy address */
+ sta_reg = sta_reg | EMAC_STACR_OC_MASK; /* new IBM emac v4 */
memcpy (&sta_reg, &value, 2); /* put in data */
out32 (EMAC_STACR + emac_reg, sta_reg);
@@ -245,12 +266,18 @@
/* wait for completion */
i = 0;
sta_reg = in32 (EMAC_STACR + emac_reg);
- while ((sta_reg & EMAC_STACR_OC) == 0) {
+#ifdef ET_DEBUG
+ printf ("a31: read : EMAC_STACR=0x%0x\n", sta_reg); /* test-only */
+#endif
+ while ((sta_reg & EMAC_STACR_OC) == EMAC_STACR_OC_MASK) {
udelay (7);
if (i > 5)
return -1;
i++;
sta_reg = in32 (EMAC_STACR + emac_reg);
+#ifdef ET_DEBUG
+ printf ("a32: read : EMAC_STACR=0x%0x\n", sta_reg); /* test-only */
+#endif
}
if ((sta_reg & EMAC_STACR_PHYE) != 0)
diff --git a/cpu/ppc4xx/sdram.c b/cpu/ppc4xx/sdram.c
index e31d59d..faeea5c 100644
--- a/cpu/ppc4xx/sdram.c
+++ b/cpu/ppc4xx/sdram.c
@@ -379,7 +379,7 @@
/*
* Enable the controller, then wait for DCEN to complete
*/
- mtsdram(mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
+ mtsdram(mem_cfg0, 0x82000000); /* DCEN=1, PMUD=0, 64-bit */
udelay(10000);
if (get_ram_size(0, mb0cf[i].size) == mb0cf[i].size) {
diff --git a/cpu/ppc4xx/serial.c b/cpu/ppc4xx/serial.c
index 83c9479..ad3ca6e 100644
--- a/cpu/ppc4xx/serial.c
+++ b/cpu/ppc4xx/serial.c
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
@@ -275,11 +275,11 @@
#define UART1_BASE CFG_PERIPHERAL_BASE + 0x00000300
#endif
-#if defined(CONFIG_440SP)
+#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
#define UART2_BASE CFG_PERIPHERAL_BASE + 0x00000600
#endif
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
#define CR0_MASK 0xdfffffff
#define CR0_EXTCLK_ENA 0x00800000
#define CR0_UDIV_POS 0
@@ -309,14 +309,18 @@
#if defined(CONFIG_UART1_CONSOLE)
#define ACTING_UART0_BASE UART1_BASE
#define ACTING_UART1_BASE UART0_BASE
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+ defined(CONFIG_440SPE)
#define UART0_SDR sdr_uart1
#define UART1_SDR sdr_uart0
#endif /* CONFIG_440GX */
#else
#define ACTING_UART0_BASE UART0_BASE
#define ACTING_UART1_BASE UART1_BASE
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+ defined(CONFIG_440SPE)
#define UART0_SDR sdr_uart0
#define UART1_SDR sdr_uart1
#endif /* CONFIG_440GX */
@@ -437,7 +441,8 @@
unsigned long tmp;
#endif
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || \
+ defined(CONFIG_440SPE)
#if defined(CONFIG_SERIAL_MULTI)
if (UART0_BASE == dev_base) {
mfsdr(UART0_SDR,reg);
@@ -466,7 +471,9 @@
serial_divs (gd->baudrate, &udiv, &bdiv);
#endif
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+ defined(CONFIG_440SPE)
reg |= udiv << CR0_UDIV_POS; /* set the UART divisor */
#if defined(CONFIG_SERIAL_MULTI)
if (UART0_BASE == dev_base) {
@@ -607,8 +614,28 @@
#else
udiv = ((mfdcr (cntrl0) & 0x3e) >> 1) + 1;
#endif /* CONFIG_405EP */
+
+#if !defined(CFG_EXT_SERIAL_CLOCK) && \
+ ( defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+ defined(CONFIG_440SPE) )
+ serial_divs (gd->baudrate, &udiv, &bdiv);
+ tmp = udiv << CR0_UDIV_POS; /* set the UART divisor */
+#if defined(CONFIG_SERIAL_MULTI)
+ if (UART0_BASE == dev_base) {
+ mtsdr (UART0_SDR, tmp);
+ } else {
+ mtsdr (UART1_SDR, tmp);
+ }
+#else
+ mtsdr (UART0_SDR, tmp);
+#endif
+
+#else
+
tmp = gd->baudrate * udiv * 16;
bdiv = (clk + tmp / 2) / tmp;
+#endif /* !defined(CFG_EXT_SERIAL_CLOCK) && (...) */
#if defined(CONFIG_SERIAL_MULTI)
out8 (dev_base + UART_LCR, 0x80); /* set DLAB bit */
diff --git a/cpu/ppc4xx/spd_sdram.c b/cpu/ppc4xx/spd_sdram.c
index c0a6933..c24456b 100644
--- a/cpu/ppc4xx/spd_sdram.c
+++ b/cpu/ppc4xx/spd_sdram.c
@@ -1007,9 +1007,9 @@
}
/*
- * program Page Management Unit
+ * program Page Management Unit (0 == enabled)
*/
- cfg0 |= SDRAM_CFG0_PMUD;
+ cfg0 &= ~SDRAM_CFG0_PMUD;
/*
* program Memory Controller Options 0
diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c
index 02b4383..e552c03 100644
--- a/cpu/ppc4xx/speed.c
+++ b/cpu/ppc4xx/speed.c
@@ -29,7 +29,11 @@
DECLARE_GLOBAL_DATA_PTR;
#define ONE_BILLION 1000000000
-
+#ifdef DEBUG
+#define DEBUGF(fmt,args...) printf(fmt ,##args)
+#else
+#define DEBUGF(fmt,args...)
+#endif
#if defined(CONFIG_405GP) || defined(CONFIG_405CR)
@@ -283,7 +287,7 @@
return sys_info.freqPCI;
}
-#elif !defined(CONFIG_440GX) && !defined(CONFIG_440SP)
+#elif !defined(CONFIG_440GX) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)
void get_sys_info (sys_info_t * sysInfo)
{
unsigned long strp0;
@@ -326,6 +330,26 @@
unsigned long m;
unsigned long prbdv0;
+#if defined(CONFIG_440SPE)
+ unsigned long sys_freq;
+ unsigned long sys_per=0;
+ unsigned long msr;
+ unsigned long pci_clock_per;
+ unsigned long sdr_ddrpll;
+
+ /*-------------------------------------------------------------------------+
+ | Get the system clock period.
+ +-------------------------------------------------------------------------*/
+ sys_per = determine_sysper();
+
+ msr = (mfmsr () & ~(MSR_EE)); /* disable interrupts */
+
+ /*-------------------------------------------------------------------------+
+ | Calculate the system clock speed from the period.
+ +-------------------------------------------------------------------------*/
+ sys_freq=(ONE_BILLION/sys_per)*1000;
+#endif
+
/* Extract configured divisors */
mfsdr( sdr_sdstp0,strp0 );
mfsdr( sdr_sdstp1,strp1 );
@@ -360,12 +384,238 @@
m = sysInfo->pllExtBusDiv * sysInfo->pllOpbDiv * sysInfo->pllFwdDivB;
/* Now calculate the individual clocks */
+#if defined(CONFIG_440SPE)
+ sysInfo->freqVCOMhz = (m * sys_freq) ;
+#else
sysInfo->freqVCOMhz = (m * CONFIG_SYS_CLK_FREQ) + (m>>1);
+#endif
sysInfo->freqProcessor = sysInfo->freqVCOMhz/sysInfo->pllFwdDivA;
sysInfo->freqPLB = sysInfo->freqVCOMhz/sysInfo->pllFwdDivB/prbdv0;
sysInfo->freqOPB = sysInfo->freqPLB/sysInfo->pllOpbDiv;
sysInfo->freqEPB = sysInfo->freqOPB/sysInfo->pllExtBusDiv;
+#if defined(CONFIG_440SPE)
+ /* Determine PCI Clock Period */
+ pci_clock_per = determine_pci_clock_per();
+ sysInfo->freqPCI = (ONE_BILLION/pci_clock_per) * 1000;
+ mfsdr(sdr_ddr0, sdr_ddrpll);
+ sysInfo->freqDDR = ((sysInfo->freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));
+#endif
+
+
+}
+
+#endif
+
+#if defined(CONFIG_440SPE)
+unsigned long determine_sysper(void)
+{
+ unsigned int fpga_clocking_reg;
+ unsigned int master_clock_selection;
+ unsigned long master_clock_per = 0;
+ unsigned long fb_div_selection;
+ unsigned int vco_div_reg_value;
+ unsigned long vco_div_selection;
+ unsigned long sys_per = 0;
+ int extClkVal;
+
+ /*-------------------------------------------------------------------------+
+ | Read FPGA reg 0 and reg 1 to get FPGA reg information
+ +-------------------------------------------------------------------------*/
+ fpga_clocking_reg = in16(FPGA_REG16);
+
+
+ /* Determine Master Clock Source Selection */
+ master_clock_selection = fpga_clocking_reg & FPGA_REG16_MASTER_CLK_MASK;
+
+ switch(master_clock_selection) {
+ case FPGA_REG16_MASTER_CLK_66_66:
+ master_clock_per = PERIOD_66_66MHZ;
+ break;
+ case FPGA_REG16_MASTER_CLK_50:
+ master_clock_per = PERIOD_50_00MHZ;
+ break;
+ case FPGA_REG16_MASTER_CLK_33_33:
+ master_clock_per = PERIOD_33_33MHZ;
+ break;
+ case FPGA_REG16_MASTER_CLK_25:
+ master_clock_per = PERIOD_25_00MHZ;
+ break;
+ case FPGA_REG16_MASTER_CLK_EXT:
+ if ((extClkVal==EXTCLK_33_33)
+ && (extClkVal==EXTCLK_50)
+ && (extClkVal==EXTCLK_66_66)
+ && (extClkVal==EXTCLK_83)) {
+ /* calculate master clock period from external clock value */
+ master_clock_per=(ONE_BILLION/extClkVal) * 1000;
+ } else {
+ /* Unsupported */
+ DEBUGF ("%s[%d] *** master clock selection failed ***\n", __FUNCTION__,__LINE__);
+ hang();
+ }
+ break;
+ default:
+ /* Unsupported */
+ DEBUGF ("%s[%d] *** master clock selection failed ***\n", __FUNCTION__,__LINE__);
+ hang();
+ break;
+ }
+
+ /* Determine FB divisors values */
+ if ((fpga_clocking_reg & FPGA_REG16_FB1_DIV_MASK) == FPGA_REG16_FB1_DIV_LOW) {
+ if ((fpga_clocking_reg & FPGA_REG16_FB2_DIV_MASK) == FPGA_REG16_FB2_DIV_LOW)
+ fb_div_selection = FPGA_FB_DIV_6;
+ else
+ fb_div_selection = FPGA_FB_DIV_12;
+ } else {
+ if ((fpga_clocking_reg & FPGA_REG16_FB2_DIV_MASK) == FPGA_REG16_FB2_DIV_LOW)
+ fb_div_selection = FPGA_FB_DIV_10;
+ else
+ fb_div_selection = FPGA_FB_DIV_20;
+ }
+
+ /* Determine VCO divisors values */
+ vco_div_reg_value = fpga_clocking_reg & FPGA_REG16_VCO_DIV_MASK;
+
+ switch(vco_div_reg_value) {
+ case FPGA_REG16_VCO_DIV_4:
+ vco_div_selection = FPGA_VCO_DIV_4;
+ break;
+ case FPGA_REG16_VCO_DIV_6:
+ vco_div_selection = FPGA_VCO_DIV_6;
+ break;
+ case FPGA_REG16_VCO_DIV_8:
+ vco_div_selection = FPGA_VCO_DIV_8;
+ break;
+ case FPGA_REG16_VCO_DIV_10:
+ default:
+ vco_div_selection = FPGA_VCO_DIV_10;
+ break;
+ }
+
+ if (master_clock_selection == FPGA_REG16_MASTER_CLK_EXT) {
+ switch(master_clock_per) {
+ case PERIOD_25_00MHZ:
+ if (fb_div_selection == FPGA_FB_DIV_12) {
+ if (vco_div_selection == FPGA_VCO_DIV_4)
+ sys_per = PERIOD_75_00MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_6)
+ sys_per = PERIOD_50_00MHZ;
+ }
+ break;
+ case PERIOD_33_33MHZ:
+ if (fb_div_selection == FPGA_FB_DIV_6) {
+ if (vco_div_selection == FPGA_VCO_DIV_4)
+ sys_per = PERIOD_50_00MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_6)
+ sys_per = PERIOD_33_33MHZ;
+ }
+ if (fb_div_selection == FPGA_FB_DIV_10) {
+ if (vco_div_selection == FPGA_VCO_DIV_4)
+ sys_per = PERIOD_83_33MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_10)
+ sys_per = PERIOD_33_33MHZ;
+ }
+ if (fb_div_selection == FPGA_FB_DIV_12) {
+ if (vco_div_selection == FPGA_VCO_DIV_4)
+ sys_per = PERIOD_100_00MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_6)
+ sys_per = PERIOD_66_66MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_8)
+ sys_per = PERIOD_50_00MHZ;
+ }
+ break;
+ case PERIOD_50_00MHZ:
+ if (fb_div_selection == FPGA_FB_DIV_6) {
+ if (vco_div_selection == FPGA_VCO_DIV_4)
+ sys_per = PERIOD_75_00MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_6)
+ sys_per = PERIOD_50_00MHZ;
+ }
+ if (fb_div_selection == FPGA_FB_DIV_10) {
+ if (vco_div_selection == FPGA_VCO_DIV_6)
+ sys_per = PERIOD_83_33MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_10)
+ sys_per = PERIOD_50_00MHZ;
+ }
+ if (fb_div_selection == FPGA_FB_DIV_12) {
+ if (vco_div_selection == FPGA_VCO_DIV_6)
+ sys_per = PERIOD_100_00MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_8)
+ sys_per = PERIOD_75_00MHZ;
+ }
+ break;
+ case PERIOD_66_66MHZ:
+ if (fb_div_selection == FPGA_FB_DIV_6) {
+ if (vco_div_selection == FPGA_VCO_DIV_4)
+ sys_per = PERIOD_100_00MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_6)
+ sys_per = PERIOD_66_66MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_8)
+ sys_per = PERIOD_50_00MHZ;
+ }
+ if (fb_div_selection == FPGA_FB_DIV_10) {
+ if (vco_div_selection == FPGA_VCO_DIV_8)
+ sys_per = PERIOD_83_33MHZ;
+ if (vco_div_selection == FPGA_VCO_DIV_10)
+ sys_per = PERIOD_66_66MHZ;
+ }
+ if (fb_div_selection == FPGA_FB_DIV_12) {
+ if (vco_div_selection == FPGA_VCO_DIV_8)
+ sys_per = PERIOD_100_00MHZ;
+ }
+ break;
+ default:
+ break;
+ }
+
+ if (sys_per == 0) {
+ /* Other combinations are not supported */
+ DEBUGF ("%s[%d] *** sys period compute failed ***\n", __FUNCTION__,__LINE__);
+ hang();
+ }
+ } else {
+ /* calcul system clock without cheking */
+ /* if engineering option clock no check is selected */
+ /* sys_per = master_clock_per * vco_div_selection / fb_div_selection */
+ sys_per = (master_clock_per/fb_div_selection) * vco_div_selection;
+ }
+
+ return(sys_per);
+
+}
+
+/*-------------------------------------------------------------------------+
+| determine_pci_clock_per.
++-------------------------------------------------------------------------*/
+unsigned long determine_pci_clock_per(void)
+{
+ unsigned long pci_clock_selection, pci_period;
+
+ /*-------------------------------------------------------------------------+
+ | Read FPGA reg 6 to get PCI 0 FPGA reg information
+ +-------------------------------------------------------------------------*/
+ pci_clock_selection = in16(FPGA_REG16); /* was reg6 averifier */
+
+
+ pci_clock_selection = pci_clock_selection & FPGA_REG16_PCI0_CLK_MASK;
+
+ switch (pci_clock_selection) {
+ case FPGA_REG16_PCI0_CLK_133_33:
+ pci_period = PERIOD_133_33MHZ;
+ break;
+ case FPGA_REG16_PCI0_CLK_100:
+ pci_period = PERIOD_100_00MHZ;
+ break;
+ case FPGA_REG16_PCI0_CLK_66_66:
+ pci_period = PERIOD_66_66MHZ;
+ break;
+ default:
+ pci_period = PERIOD_33_33MHZ;;
+ break;
+ }
+
+ return(pci_period);
}
#endif
diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S
index 647088f..60ed2d5 100644
--- a/cpu/ppc4xx/start.S
+++ b/cpu/ppc4xx/start.S
@@ -155,6 +155,11 @@
/**************************************************************************/
_start_440:
+ /*----------------------------------------------------------------+
+ | Core bug fix. Clear the esr
+ +-----------------------------------------------------------------*/
+ li r0,0
+ mtspr esr,r0
/*----------------------------------------------------------------*/
/* Clear and set up some registers. */
/*----------------------------------------------------------------*/
@@ -166,7 +171,7 @@
mtspr srr1,r0
mtspr csrr0,r0
mtspr csrr1,r0
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP) /* NOTE: 440GX adds machine check status regs */
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) /* NOTE: 440GX adds machine check status regs */
mtspr mcsrr0,r0
mtspr mcsrr1,r0
mfspr r1, mcsr
@@ -200,6 +205,31 @@
ori r1,r1,0x6000 /* cache touch */
mtspr ccr0,r1
+#if defined (CONFIG_440SPE)
+ /*----------------------------------------------------------------+
+ | Initialize Core Configuration Reg1.
+ | a. ICDPEI: Record even parity. Normal operation.
+ | b. ICTPEI: Record even parity. Normal operation.
+ | c. DCTPEI: Record even parity. Normal operation.
+ | d. DCDPEI: Record even parity. Normal operation.
+ | e. DCUPEI: Record even parity. Normal operation.
+ | f. DCMPEI: Record even parity. Normal operation.
+ | g. FCOM: Normal operation
+ | h. MMUPEI: Record even parity. Normal operation.
+ | i. FFF: Flush only as much data as necessary.
+ | j. TCS: Timebase increments from CPU clock.
+ +-----------------------------------------------------------------*/
+ li r0,0
+ mtspr ccr1, r0
+
+ /*----------------------------------------------------------------+
+ | Reset the timebase.
+ | The previous write to CCR1 sets the timebase source.
+ +-----------------------------------------------------------------*/
+ mtspr tbl, r0
+ mtspr tbu, r0
+#endif
+
/*----------------------------------------------------------------*/
/* Setup interrupt vectors */
/*----------------------------------------------------------------*/
@@ -261,20 +291,47 @@
mtspr ivlim,r1
mtspr dvlim,r1
+ /*----------------------------------------------------------------+
+ |Initialize MMUCR[STID] = 0.
+ +-----------------------------------------------------------------*/
+ mfspr r0,mmucr
+ addis r1,0,0xFFFF
+ ori r1,r1,0xFF00
+ and r0,r0,r1
+ mtspr mmucr,r0
+
/*----------------------------------------------------------------*/
/* Clear all TLB entries -- TID = 0, TS = 0 */
/*----------------------------------------------------------------*/
- mtspr mmucr,r0
+ addis r0,0,0x0000
li r1,0x003f /* 64 TLB entries */
mtctr r1
-0: tlbwe r0,r1,0x0000 /* Invalidate all entries (V=0)*/
+rsttlb: tlbwe r0,r1,0x0000 /* Invalidate all entries (V=0)*/
+ tlbwe r0,r1,0x0001
+ tlbwe r0,r1,0x0002
subi r1,r1,0x0001
- bdnz 0b
+ bdnz rsttlb
/*----------------------------------------------------------------*/
/* TLB entry setup -- step thru tlbtab */
/*----------------------------------------------------------------*/
+#if defined(CONFIG_440SPE)
+ /*----------------------------------------------------------------*/
+ /* We have different TLB tables for revA and rev B of 440SPe */
+ /*----------------------------------------------------------------*/
+ mfspr r1, PVR
+ lis r0,0x5342
+ ori r0,r0,0x1891
+ cmpw r7,r1,r0
+ bne r7,..revA
+ bl tlbtabB
+ b ..goon
+..revA:
+ bl tlbtabA
+..goon:
+#else
bl tlbtab /* Get tlbtab pointer */
+#endif
mr r5,r0
li r1,0x003f /* 64 TLB entries max */
mtctr r1
@@ -377,7 +434,7 @@
addi r3,r3,32
bdnz ..d_ag
#else
-#if defined (CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined (CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
mtdcr l2_cache_cfg,r0 /* Ensure L2 Cache is off */
#endif
mtdcr isram0_sb1cr,r0 /* Disable bank 1 */
@@ -404,6 +461,19 @@
lis r1, 0x8003
ori r1,r1, 0x0980 /* fourth 64k */
mtdcr isram0_sb3cr,r1
+#elif defined(CONFIG_440SPE)
+ lis r1,0x0000 /* BAS = 0000_0000 */
+ ori r1,r1,0x0984 /* first 64k */
+ mtdcr isram0_sb0cr,r1
+ lis r1,0x0001
+ ori r1,r1,0x0984 /* second 64k */
+ mtdcr isram0_sb1cr,r1
+ lis r1, 0x0002
+ ori r1,r1, 0x0984 /* third 64k */
+ mtdcr isram0_sb2cr,r1
+ lis r1, 0x0003
+ ori r1,r1, 0x0984 /* fourth 64k */
+ mtdcr isram0_sb3cr,r1
#else
ori r1,r1,0x0380 /* 8k rw */
mtdcr isram0_sb0cr,r1
@@ -1197,7 +1267,7 @@
*/
.globl relocate_code
relocate_code:
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SPE)
/*
* On some 440er platforms the cache is enabled in the first TLB (Boot-CS)
* to speed up the boot process. Now this cache needs to be disabled.
@@ -1412,7 +1482,7 @@
cmplw 0, r7, r8
blt 4b
-#if !defined(CONFIG_440_GX)
+#if !defined(CONFIG_440GX) && !defined(CONFIG_440SPE)
addi r7,r0,0x1000 /* set ME bit (Machine Exceptions) */
oris r7,r7,0x0002 /* set CE bit (Critical Exceptions) */
mtmsr r7 /* change MSR */
diff --git a/cpu/ppc4xx/vecnum.h b/cpu/ppc4xx/vecnum.h
index cbfe41d..93cef02 100644
--- a/cpu/ppc4xx/vecnum.h
+++ b/cpu/ppc4xx/vecnum.h
@@ -31,7 +31,48 @@
#ifndef _VECNUMS_H_
#define _VECNUMS_H_
-#if defined(CONFIG_440SP)
+#if defined(CONFIG_440SPE)
+/* UIC 0 */
+#define VECNUM_U0 0 /* UART0 */
+#define VECNUM_U1 1 /* UART1 */
+#define VECNUM_IIC0 2 /* IIC0 */
+#define VECNUM_IIC1 3 /* IIC1 */
+#define VECNUM_PIM 4 /* PCI inbound message */
+#define VECNUM_PCRW 5 /* PCI command reg write */
+#define VECNUM_PPM 6 /* PCI power management */
+#define VECNUM_MSI0 7 /* PCI MSI level 0 */
+#define VECNUM_MSI1 8 /* PCI MSI level 0 */
+#define VECNUM_MSI2 9 /* PCI MSI level 0 */
+#define VECNUM_D0 12 /* DMA channel 0 */
+#define VECNUM_D1 13 /* DMA channel 1 */
+#define VECNUM_D2 14 /* DMA channel 2 */
+#define VECNUM_D3 15 /* DMA channel 3 */
+#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */
+#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */
+
+/* UIC 1 */
+#define VECNUM_MS (32 + 1 ) /* MAL SERR */
+#define VECNUM_TXDE (32 + 2 ) /* MAL TXDE */
+#define VECNUM_RXDE (32 + 3 ) /* MAL RXDE */
+#define VECNUM_MTE (32 + 6 ) /* MAL Tx EOB */
+#define VECNUM_MRE (32 + 7 ) /* MAL Rx EOB */
+#define VECNUM_CT0 (32 + 12 ) /* GPT compare timer 0 */
+#define VECNUM_CT1 (32 + 13 ) /* GPT compare timer 1 */
+#define VECNUM_CT2 (32 + 14 ) /* GPT compare timer 2 */
+#define VECNUM_CT3 (32 + 15 ) /* GPT compare timer 3 */
+#define VECNUM_CT4 (32 + 16 ) /* GPT compare timer 4 */
+#define VECNUM_ETH0 (32 + 28) /* Ethernet interrupt status */
+#define VECNUM_EWU0 (32 + 29) /* Emac wakeup */
+
+/* UIC 2 */
+#define VECNUM_EIR5 (62 + 24) /* External interrupt 5 */
+#define VECNUM_EIR4 (62 + 25) /* External interrupt 4 */
+#define VECNUM_EIR3 (62 + 26) /* External interrupt 3 */
+#define VECNUM_EIR2 (62 + 27) /* External interrupt 2 */
+#define VECNUM_EIR1 (62 + 28) /* External interrupt 1 */
+#define VECNUM_EIR0 (62 + 29) /* External interrupt 0 */
+
+#elif defined(CONFIG_440SP)
/* UIC 0 */
#define VECNUM_U0 0 /* UART0 */
diff --git a/doc/README.440-DDR-performance b/doc/README.440-DDR-performance
new file mode 100644
index 0000000..17bc747
--- /dev/null
+++ b/doc/README.440-DDR-performance
@@ -0,0 +1,90 @@
+AMCC suggested to set the PMU bit to 0 for best performace on the
+PPC440 DDR controller. The 440er common DDR setup files (sdram.c &
+spd_sdram.c) are changed accordingly. So all 440er boards using
+these setup routines will automatically receive this performance
+increase.
+
+Please see below some benchmarks done by AMCC to demonstrate this
+performance changes:
+
+
+----------------------------------------
+SDRAM0_CFG0[PMU] = 1 (U-boot default for Bamboo, Yosemite and Yellowstone)
+----------------------------------------
+Stream benchmark results
+-------------------------------------------------------------
+This system uses 8 bytes per DOUBLE PRECISION word.
+-------------------------------------------------------------
+Array size = 2000000, Offset = 0
+Total memory required = 45.8 MB.
+Each test is run 10 times, but only
+the *best* time for each is used.
+-------------------------------------------------------------
+Your clock granularity/precision appears to be 1 microseconds.
+Each test below will take on the order of 112345 microseconds.
+ (= 112345 clock ticks)
+Increase the size of the arrays if this shows that you are not getting
+at least 20 clock ticks per test.
+-------------------------------------------------------------
+WARNING -- The above is only a rough guideline.
+For best results, please be sure you know the precision of your system
+timer.
+-------------------------------------------------------------
+Function Rate (MB/s) RMS time Min time Max time
+Copy: 256.7683 0.1248 0.1246 0.1250
+Scale: 246.0157 0.1302 0.1301 0.1302
+Add: 255.0316 0.1883 0.1882 0.1885
+Triad: 253.1245 0.1897 0.1896 0.1899
+
+
+TTCP Benchmark Results
+ttcp-t: socket
+ttcp-t: connect
+ttcp-t: buflen=8192, nbuf=2048, align=16384/0, port=5000 tcp ->
+localhost
+ttcp-t: 16777216 bytes in 0.28 real seconds = 454.29 Mbit/sec +++
+ttcp-t: 2048 I/O calls, msec/call = 0.14, calls/sec = 7268.57
+ttcp-t: 0.0user 0.1sys 0:00real 60% 0i+0d 0maxrss 0+2pf 3+1506csw
+
+----------------------------------------
+SDRAM0_CFG0[PMU] = 0 (Suggested modification)
+Setting PMU = 0 provides a noticeable performance improvement *2% to
+5% improvement in memory performance.
+*Improves the Mbit/sec for TTCP benchmark by almost 76%.
+----------------------------------------
+Stream benchmark results
+-------------------------------------------------------------
+This system uses 8 bytes per DOUBLE PRECISION word.
+-------------------------------------------------------------
+Array size = 2000000, Offset = 0
+Total memory required = 45.8 MB.
+Each test is run 10 times, but only
+the *best* time for each is used.
+-------------------------------------------------------------
+Your clock granularity/precision appears to be 1 microseconds.
+Each test below will take on the order of 120066 microseconds.
+ (= 120066 clock ticks)
+Increase the size of the arrays if this shows that you are not getting
+at least 20 clock ticks per test.
+-------------------------------------------------------------
+WARNING -- The above is only a rough guideline.
+For best results, please be sure you know the precision of your system
+timer.
+-------------------------------------------------------------
+Function Rate (MB/s) RMS time Min time Max time
+Copy: 262.5167 0.1221 0.1219 0.1223
+Scale: 258.4856 0.1238 0.1238 0.1240
+Add: 262.5404 0.1829 0.1828 0.1831
+Triad: 266.8594 0.1800 0.1799 0.1802
+
+TTCP Benchmark Results
+ttcp-t: socket
+ttcp-t: connect
+ttcp-t: buflen=8192, nbuf=2048, align=16384/0, port=5000 tcp ->
+localhost
+ttcp-t: 16777216 bytes in 0.16 real seconds = 804.06 Mbit/sec +++
+ttcp-t: 2048 I/O calls, msec/call = 0.08, calls/sec = 12864.89
+ttcp-t: 0.0user 0.0sys 0:00real 46% 0i+0d 0maxrss 0+2pf 120+1csw
+
+
+2006-07-28, Stefan Roese <sr@denx.de>
diff --git a/doc/README.bamboo b/doc/README.bamboo
new file mode 100644
index 0000000..b50be01
--- /dev/null
+++ b/doc/README.bamboo
@@ -0,0 +1,15 @@
+The configuration for the AMCC 440EP eval board "Bamboo" was changed
+to only use 384 kbytes of FLASH for the U-Boot image. This way the
+redundant environment can be saved in the remaining 2 sectors of the
+same flash chip.
+
+Caution: With an upgrade from an earlier U-Boot version the current
+environment will be erased since the environment is now saved in
+different sectors. By using the following command the environment can
+be saved after upgrading the U-Boot image and *before* resetting the
+board:
+
+setenv recover_env 'prot off FFF80000 FFF9FFFF;era FFF80000 FFF9FFFF;' \
+ 'cp.b FFF60000 FFF80000 20000'
+
+2006-07-27, Stefan Roese <sr@denx.de>
diff --git a/drivers/Makefile b/drivers/Makefile
index e6176ed..9be95c7 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -31,7 +31,7 @@
bcm570x.o bcm570x_autoneg.o cfb_console.o cfi_flash.o \
cs8900.o ct69000.o dataflash.o dc2114x.o dm9000x.o \
e1000.o eepro100.o \
- i8042.o i82365.o inca-ip_sw.o keyboard.o \
+ i8042.o inca-ip_sw.o keyboard.o \
lan91c96.o \
natsemi.o ne2000.o netarm_eth.o netconsole.o \
ns16550.o ns8382x.o ns87308.o ns7520_eth.o omap1510_i2c.o \
@@ -48,7 +48,9 @@
ti_pci1410a.o tigon3.o tsec.o \
usbdcore.o usbdcore_ep0.o usbdcore_omap1510.o usbtty.o \
videomodes.o w83c553f.o \
- ks8695eth.o
+ ks8695eth.o \
+ pxa_pcmcia.o mpc8xx_pcmcia.o tqm8xx_pcmcia.o \
+ rpx_pcmcia.o
all: $(LIB)
diff --git a/drivers/dm9000x.c b/drivers/dm9000x.c
index 0e475d4..6877076 100644
--- a/drivers/dm9000x.c
+++ b/drivers/dm9000x.c
@@ -436,6 +436,9 @@
u8 rxbyte, *rdptr = (u8 *) NetRxPackets[0];
u16 RxStatus, RxLen = 0;
u32 tmplen, i;
+#ifdef CONFIG_DM9000_USE_32BIT
+ u32 tmpdata;
+#endif
/* Check packet ready or not */
DM9000_ior(DM9000_MRCMDX); /* Dummy read */
diff --git a/drivers/keyboard.c b/drivers/keyboard.c
index 41eccf2..9975202 100644
--- a/drivers/keyboard.c
+++ b/drivers/keyboard.c
@@ -33,7 +33,7 @@
#define KBD_BUFFER_LEN 0x20 /* size of the keyboardbuffer */
-#if defined(CONFIG_MPC5xxx) || defined(CONFIG_MPC85xx)
+#if defined(CONFIG_MPC5xxx) || defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
int ps2ser_check(void);
#endif
@@ -75,7 +75,7 @@
/* test if a character is in the queue */
static int kbd_testc(void)
{
-#if defined(CONFIG_MPC5xxx) || defined(CONFIG_MPC85xx)
+#if defined(CONFIG_MPC5xxx) || defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
/* no ISR is used, so received chars must be polled */
ps2ser_check();
#endif
@@ -90,7 +90,7 @@
{
char c;
while(in_pointer==out_pointer) {
-#if defined(CONFIG_MPC5xxx) || defined(CONFIG_MPC85xx)
+#if defined(CONFIG_MPC5xxx) || defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
/* no ISR is used, so received chars must be polled */
ps2ser_check();
#endif
diff --git a/drivers/mpc8xx_pcmcia.c b/drivers/mpc8xx_pcmcia.c
new file mode 100644
index 0000000..399a719
--- /dev/null
+++ b/drivers/mpc8xx_pcmcia.c
@@ -0,0 +1,304 @@
+#include <common.h>
+#if defined(CONFIG_8xx)
+#include <mpc8xx.h>
+#endif
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#if defined(CONFIG_8xx) && defined(CONFIG_PCMCIA)
+
+#if defined(CONFIG_IDE_8xx_PCCARD)
+extern int check_ide_device (int slot);
+#endif
+
+extern int pcmcia_hardware_enable (int slot);
+extern int pcmcia_voltage_set(int slot, int vcc, int vpp);
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+extern int pcmcia_hardware_disable(int slot);
+#endif
+
+static u_int m8xx_get_graycode(u_int size);
+#if 0 /* Disabled */
+static u_int m8xx_get_speed(u_int ns, u_int is_io);
+#endif
+
+/* look up table for pgcrx registers */
+u_int *pcmcia_pgcrx[2] = {
+ &((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pgcra,
+ &((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pgcrb,
+};
+
+/*
+ * Search this table to see if the windowsize is
+ * supported...
+ */
+
+#define M8XX_SIZES_NO 32
+
+static const u_int m8xx_size_to_gray[M8XX_SIZES_NO] =
+{ 0x00000001, 0x00000002, 0x00000008, 0x00000004,
+ 0x00000080, 0x00000040, 0x00000010, 0x00000020,
+ 0x00008000, 0x00004000, 0x00001000, 0x00002000,
+ 0x00000100, 0x00000200, 0x00000800, 0x00000400,
+
+ 0x0fffffff, 0xffffffff, 0xffffffff, 0xffffffff,
+ 0x01000000, 0x02000000, 0xffffffff, 0x04000000,
+ 0x00010000, 0x00020000, 0x00080000, 0x00040000,
+ 0x00800000, 0x00400000, 0x00100000, 0x00200000 };
+
+
+/* -------------------------------------------------------------------- */
+
+#ifdef CONFIG_HMI10
+#define HMI10_FRAM_TIMING ( PCMCIA_SHT(2) \
+ | PCMCIA_SST(2) \
+ | PCMCIA_SL(4))
+#endif
+
+#if defined(CONFIG_LWMON) || defined(CONFIG_NSCU)
+#define CFG_PCMCIA_TIMING ( PCMCIA_SHT(9) \
+ | PCMCIA_SST(3) \
+ | PCMCIA_SL(12))
+#else
+#define CFG_PCMCIA_TIMING ( PCMCIA_SHT(2) \
+ | PCMCIA_SST(4) \
+ | PCMCIA_SL(9))
+#endif
+
+/* -------------------------------------------------------------------- */
+
+int pcmcia_on (void)
+{
+ u_long reg, base;
+ pcmcia_win_t *win;
+ u_int slotbit;
+ u_int rc, slot;
+ int i;
+
+ debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+ /* intialize the fixed memory windows */
+ win = (pcmcia_win_t *)(&((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pbr0);
+ base = CFG_PCMCIA_MEM_ADDR;
+
+ if((reg = m8xx_get_graycode(CFG_PCMCIA_MEM_SIZE)) == -1) {
+ printf ("Cannot set window size to 0x%08x\n",
+ CFG_PCMCIA_MEM_SIZE);
+ return (1);
+ }
+
+ slotbit = PCMCIA_SLOT_x;
+ for (i=0; i<PCMCIA_MEM_WIN_NO; ++i) {
+ win->br = base;
+
+#if (PCMCIA_SOCKETS_NO == 2)
+ if (i == 4) /* Another slot starting from win 4 */
+ slotbit = (slotbit ? PCMCIA_PSLOT_A : PCMCIA_PSLOT_B);
+#endif
+ switch (i) {
+#ifdef CONFIG_IDE_8xx_PCCARD
+ case 4:
+#ifdef CONFIG_HMI10
+ { /* map FRAM area */
+ win->or = ( PCMCIA_BSIZE_256K
+ | PCMCIA_PPS_8
+ | PCMCIA_PRS_ATTR
+ | slotbit
+ | PCMCIA_PV
+ | HMI10_FRAM_TIMING );
+ break;
+ }
+#endif
+ case 0: { /* map attribute memory */
+ win->or = ( PCMCIA_BSIZE_64M
+ | PCMCIA_PPS_8
+ | PCMCIA_PRS_ATTR
+ | slotbit
+ | PCMCIA_PV
+ | CFG_PCMCIA_TIMING );
+ break;
+ }
+ case 5:
+ case 1: { /* map I/O window for data reg */
+ win->or = ( PCMCIA_BSIZE_1K
+ | PCMCIA_PPS_16
+ | PCMCIA_PRS_IO
+ | slotbit
+ | PCMCIA_PV
+ | CFG_PCMCIA_TIMING );
+ break;
+ }
+ case 6:
+ case 2: { /* map I/O window for cmd/ctrl reg block */
+ win->or = ( PCMCIA_BSIZE_1K
+ | PCMCIA_PPS_8
+ | PCMCIA_PRS_IO
+ | slotbit
+ | PCMCIA_PV
+ | CFG_PCMCIA_TIMING );
+ break;
+ }
+#endif /* CONFIG_IDE_8xx_PCCARD */
+#ifdef CONFIG_HMI10
+ case 3: { /* map I/O window for 4xUART data/ctrl */
+ win->br += 0x40000;
+ win->or = ( PCMCIA_BSIZE_256K
+ | PCMCIA_PPS_8
+ | PCMCIA_PRS_IO
+ | slotbit
+ | PCMCIA_PV
+ | CFG_PCMCIA_TIMING );
+ break;
+ }
+#endif /* CONFIG_HMI10 */
+ default: /* set to not valid */
+ win->or = 0;
+ break;
+ }
+
+ debug ("MemWin %d: PBR 0x%08lX POR %08lX\n",
+ i, win->br, win->or);
+ base += CFG_PCMCIA_MEM_SIZE;
+ ++win;
+ }
+
+ for (i=0, rc=0, slot=_slot_; i<PCMCIA_SOCKETS_NO; i++, slot = !slot) {
+ /* turn off voltage */
+ if ((rc = pcmcia_voltage_set(slot, 0, 0)))
+ continue;
+
+ /* Enable external hardware */
+ if ((rc = pcmcia_hardware_enable(slot)))
+ continue;
+
+#ifdef CONFIG_IDE_8xx_PCCARD
+ if ((rc = check_ide_device(i)))
+ continue;
+#endif
+ }
+ return rc;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_off (void)
+{
+ int i;
+ pcmcia_win_t *win;
+
+ printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+ /* clear interrupt state, and disable interrupts */
+ ((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pscr = PCMCIA_MASK(_slot_);
+ ((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+ /* turn off interrupt and disable CxOE */
+ PCMCIA_PGCRX(_slot_) = __MY_PCMCIA_GCRX_CXOE;
+
+ /* turn off memory windows */
+ win = (pcmcia_win_t *)(&((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pbr0);
+
+ for (i=0; i<PCMCIA_MEM_WIN_NO; ++i) {
+ /* disable memory window */
+ win->or = 0;
+ ++win;
+ }
+
+ /* turn off voltage */
+ pcmcia_voltage_set(_slot_, 0, 0);
+
+ /* disable external hardware */
+ printf ("Shutdown and Poweroff " PCMCIA_SLOT_MSG "\n");
+ pcmcia_hardware_disable(_slot_);
+ return 0;
+}
+#endif /* CFG_CMD_PCMCIA */
+
+
+static u_int m8xx_get_graycode(u_int size)
+{
+ u_int k;
+
+ for (k = 0; k < M8XX_SIZES_NO; k++) {
+ if(m8xx_size_to_gray[k] == size)
+ break;
+ }
+
+ if((k == M8XX_SIZES_NO) || (m8xx_size_to_gray[k] == -1))
+ k = -1;
+
+ return k;
+}
+
+#if 0
+
+#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE)
+
+/* The RPX boards seems to have it's bus monitor timeout set to 6*8 clocks.
+ * SYPCR is write once only, therefore must the slowest memory be faster
+ * than the bus monitor or we will get a machine check due to the bus timeout.
+ */
+#undef PCMCIA_BMT_LIMIT
+#define PCMCIA_BMT_LIMIT (6*8)
+#endif
+
+static u_int m8xx_get_speed(u_int ns, u_int is_io)
+{
+ u_int reg, clocks, psst, psl, psht;
+
+ if(!ns) {
+
+ /*
+ * We get called with IO maps setup to 0ns
+ * if not specified by the user.
+ * They should be 255ns.
+ */
+
+ if(is_io)
+ ns = 255;
+ else
+ ns = 100; /* fast memory if 0 */
+ }
+
+ /*
+ * In PSST, PSL, PSHT fields we tell the controller
+ * timing parameters in CLKOUT clock cycles.
+ * CLKOUT is the same as GCLK2_50.
+ */
+
+ /* how we want to adjust the timing - in percent */
+
+#define ADJ 180 /* 80 % longer accesstime - to be sure */
+
+ clocks = ((M8XX_BUSFREQ / 1000) * ns) / 1000;
+ clocks = (clocks * ADJ) / (100*1000);
+
+ if(clocks >= PCMCIA_BMT_LIMIT) {
+ DEBUG(0, "Max access time limit reached\n");
+ clocks = PCMCIA_BMT_LIMIT-1;
+ }
+
+ psst = clocks / 7; /* setup time */
+ psht = clocks / 7; /* hold time */
+ psl = (clocks * 5) / 7; /* strobe length */
+
+ psst += clocks - (psst + psht + psl);
+
+ reg = psst << 12;
+ reg |= psl << 7;
+ reg |= psht << 16;
+
+ return reg;
+}
+#endif /* 0 */
+
+#endif /* CONFIG_8xx && CONFIG_PCMCIA */
diff --git a/drivers/pci_indirect.c b/drivers/pci_indirect.c
index f0c4a1c..d7be081 100644
--- a/drivers/pci_indirect.c
+++ b/drivers/pci_indirect.c
@@ -60,7 +60,7 @@
cfg_##rw(val, hose->cfg_data + (offset & mask), type, op); \
return 0; \
}
-#elif defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#elif defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SPE)
#define INDIRECT_PCI_OP(rw, size, type, op, mask) \
static int \
indirect_##rw##_config_##size(struct pci_controller *hose, \
diff --git a/drivers/ps2ser.c b/drivers/ps2ser.c
index 8aea8fd..4e304f7 100644
--- a/drivers/ps2ser.c
+++ b/drivers/ps2ser.c
@@ -20,7 +20,7 @@
#include <asm/io.h>
#include <asm/atomic.h>
#include <ps2mult.h>
-#ifdef CFG_NS16550
+#if defined(CFG_NS16550) || defined(CONFIG_MPC85xx)
#include <ns16550.h>
#endif
@@ -49,7 +49,7 @@
#error CONFIG_PS2SERIAL must be in 1 ... 6
#endif
-#elif defined(CONFIG_MPC85xx)
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
#if CONFIG_PS2SERIAL == 1
#define COM_BASE (CFG_CCSRBAR+0x4500)
@@ -59,13 +59,13 @@
#error CONFIG_PS2SERIAL must be in 1 ... 2
#endif
-#endif /* CONFIG_MPC5xxx / CONFIG_MPC85xx */
+#endif /* CONFIG_MPC5xxx / CONFIG_MPC8540 / other */
static int ps2ser_getc_hw(void);
static void ps2ser_interrupt(void *dev_id);
extern struct serial_state rs_table[]; /* in serial.c */
-#if !defined(CONFIG_MPC5xxx) && !defined(CONFIG_MPC85xx)
+#if !defined(CONFIG_MPC5xxx) && !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8541) && !defined(CONFIG_MPC8555)
static struct serial_state *state;
#endif
@@ -120,7 +120,7 @@
return (0);
}
-#elif defined(CONFIG_MPC85xx)
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
int ps2ser_init(void)
{
NS16550_t com_port = (NS16550_t)COM_BASE;
@@ -136,7 +136,7 @@
return (0);
}
-#else /* !CONFIG_MPC5xxx && !CONFIG_MPC85xx */
+#else /* !CONFIG_MPC5xxx && !CONFIG_MPC8540 / other */
static inline unsigned int ps2ser_in(int offset)
{
@@ -180,13 +180,13 @@
return 0;
}
-#endif /* CONFIG_MPC5xxx / CONFIG_MPC85xx / other */
+#endif /* CONFIG_MPC5xxx / CONFIG_MPC8540 / other */
void ps2ser_putc(int chr)
{
#ifdef CONFIG_MPC5xxx
volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
-#elif defined(CONFIG_MPC85xx)
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
NS16550_t com_port = (NS16550_t)COM_BASE;
#endif
#ifdef DEBUG
@@ -197,7 +197,7 @@
while (!(psc->psc_status & PSC_SR_TXRDY));
psc->psc_buffer_8 = chr;
-#elif defined(CONFIG_MPC85xx)
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
while ((com_port->lsr & LSR_THRE) == 0);
com_port->thr = chr;
#else
@@ -211,7 +211,7 @@
{
#ifdef CONFIG_MPC5xxx
volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
-#elif defined(CONFIG_MPC85xx)
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
NS16550_t com_port = (NS16550_t)COM_BASE;
#endif
int res = -1;
@@ -220,7 +220,7 @@
if (psc->psc_status & PSC_SR_RXRDY) {
res = (psc->psc_buffer_8);
}
-#elif defined(CONFIG_MPC85xx)
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
if (com_port->lsr & LSR_DR) {
res = com_port->rbr;
}
@@ -279,7 +279,7 @@
{
#ifdef CONFIG_MPC5xxx
volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
-#elif defined(CONFIG_MPC85xx)
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
NS16550_t com_port = (NS16550_t)COM_BASE;
#endif
int chr;
@@ -289,7 +289,7 @@
chr = ps2ser_getc_hw();
#ifdef CONFIG_MPC5xxx
status = psc->psc_status;
-#elif defined(CONFIG_MPC85xx)
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
status = com_port->lsr;
#else
status = ps2ser_in(UART_IIR);
@@ -305,7 +305,7 @@
}
#ifdef CONFIG_MPC5xxx
} while (status & PSC_SR_RXRDY);
-#elif defined(CONFIG_MPC85xx)
+#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || defined(CONFIG_MPC8555)
} while (status & LSR_DR);
#else
} while (status & UART_IIR_RDI);
diff --git a/drivers/pxa_pcmcia.c b/drivers/pxa_pcmcia.c
new file mode 100644
index 0000000..d9d38bb
--- /dev/null
+++ b/drivers/pxa_pcmcia.c
@@ -0,0 +1,95 @@
+#include <common.h>
+#include <config.h>
+
+#ifdef CONFIG_PXA_PCMCIA
+
+#include <pcmcia.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/io.h>
+
+static inline void msWait(unsigned msVal)
+{
+ udelay(msVal*1000);
+}
+
+int pcmcia_on (void)
+{
+ unsigned int reg_arr[] = {
+ 0x48000028, CFG_MCMEM0_VAL,
+ 0x4800002c, CFG_MCMEM1_VAL,
+ 0x48000030, CFG_MCATT0_VAL,
+ 0x48000034, CFG_MCATT1_VAL,
+ 0x48000038, CFG_MCIO0_VAL,
+ 0x4800003c, CFG_MCIO1_VAL,
+
+ 0, 0
+ };
+ int i, rc;
+
+#ifdef CONFIG_EXADRON1
+ int cardDetect;
+ volatile unsigned int *v_pBCRReg =
+ (volatile unsigned int *) 0x08000000;
+#endif
+
+ debug ("%s\n", __FUNCTION__);
+
+ i = 0;
+ while (reg_arr[i])
+ *((volatile unsigned int *) reg_arr[i++]) |= reg_arr[i++];
+ udelay (1000);
+
+ debug ("%s: programmed mem controller \n", __FUNCTION__);
+
+#ifdef CONFIG_EXADRON1
+
+/*define useful BCR masks */
+#define BCR_CF_INIT_VAL 0x00007230
+#define BCR_CF_PWRON_BUSOFF_RESETOFF_VAL 0x00007231
+#define BCR_CF_PWRON_BUSOFF_RESETON_VAL 0x00007233
+#define BCR_CF_PWRON_BUSON_RESETON_VAL 0x00007213
+#define BCR_CF_PWRON_BUSON_RESETOFF_VAL 0x00007211
+
+ /* we see from the GPIO bit if the card is present */
+ cardDetect = !(GPLR0 & GPIO_bit (14));
+
+ if (cardDetect) {
+ printf ("No PCMCIA card found!\n");
+ }
+
+ /* reset the card via the BCR line */
+ *v_pBCRReg = (unsigned) BCR_CF_INIT_VAL;
+ msWait (500);
+
+ *v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSOFF_RESETOFF_VAL;
+ msWait (500);
+
+ *v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSOFF_RESETON_VAL;
+ msWait (500);
+
+ *v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSON_RESETON_VAL;
+ msWait (500);
+
+ *v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSON_RESETOFF_VAL;
+ msWait (1500);
+
+ /* enable address bus */
+ GPCR1 = 0x01;
+ /* and the first CF slot */
+ MECR = 0x00000002;
+
+#endif /* EXADRON 1 */
+
+ rc = check_ide_device (0); /* use just slot 0 */
+
+ return rc;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_off (void)
+{
+ return 0;
+}
+#endif
+
+#endif /* CONFIG_PXA_PCMCIA */
diff --git a/drivers/rpx_pcmcia.c b/drivers/rpx_pcmcia.c
new file mode 100644
index 0000000..2a0a9e0
--- /dev/null
+++ b/drivers/rpx_pcmcia.c
@@ -0,0 +1,73 @@
+/* -------------------------------------------------------------------- */
+/* RPX Boards from Embedded Planet */
+/* -------------------------------------------------------------------- */
+#include <common.h>
+#ifdef CONFIG_8xx
+#include <mpc8xx.h>
+#endif
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if CONFIG_COMMANDS & CFG_CMD_PCMCIA
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#if defined(CONFIG_PCMCIA) \
+ && (defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE))
+
+#define PCMCIA_BOARD_MSG "RPX CLASSIC or RPX LITE"
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+ u_long reg = 0;
+
+ switch(vcc) {
+ case 0: break;
+ case 33: reg |= BCSR1_PCVCTL4; break;
+ case 50: reg |= BCSR1_PCVCTL5; break;
+ default: return 1;
+ }
+
+ switch(vpp) {
+ case 0: break;
+ case 33:
+ case 50:
+ if(vcc == vpp)
+ reg |= BCSR1_PCVCTL6;
+ else
+ return 1;
+ break;
+ case 120:
+ reg |= BCSR1_PCVCTL7;
+ default: return 1;
+ }
+
+ /* first, turn off all power */
+ *((uint *)RPX_CSR_ADDR) &= ~(BCSR1_PCVCTL4 | BCSR1_PCVCTL5
+ | BCSR1_PCVCTL6 | BCSR1_PCVCTL7);
+
+ /* enable new powersettings */
+ *((uint *)RPX_CSR_ADDR) |= reg;
+
+ return 0;
+}
+
+int pcmcia_hardware_enable (int slot)
+{
+ return 0; /* No hardware to enable */
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+static int pcmcia_hardware_disable(int slot)
+{
+ return 0; /* No hardware to disable */
+}
+#endif /* CONFIG_COMMANDS & CFG_CMD_PCMCIA */
+
+
+#endif /* CONFIG_PCMCIA && (CONFIG_RPXCLASSIC || CONFIG_RPXLITE) */
diff --git a/drivers/s3c4510b_eth.c b/drivers/s3c4510b_eth.c
index 0274dd2..48901aa 100644
--- a/drivers/s3c4510b_eth.c
+++ b/drivers/s3c4510b_eth.c
@@ -175,7 +175,7 @@
}
/* copy user data into frame data pointer */
- memcpy((void *)eth->m_curTX_FD->m_frameDataPtr.bf.dataPtr,
+ memcpy((void *)(eth->m_curTX_FD->m_frameDataPtr.bf.dataPtr),
(void *)packet,
length);
diff --git a/drivers/tqm8xx_pcmcia.c b/drivers/tqm8xx_pcmcia.c
new file mode 100644
index 0000000..a0f53cd
--- /dev/null
+++ b/drivers/tqm8xx_pcmcia.c
@@ -0,0 +1,330 @@
+/* -------------------------------------------------------------------- */
+/* TQM8xxL Boards by TQ Components */
+/* SC8xx Boards by SinoVee Microsystems */
+/* -------------------------------------------------------------------- */
+#include <common.h>
+#ifdef CONFIG_8xx
+#include <mpc8xx.h>
+#endif
+#include <pcmcia.h>
+
+#undef CONFIG_PCMCIA
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define CONFIG_PCMCIA
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define CONFIG_PCMCIA
+#endif
+
+#if defined(CONFIG_PCMCIA) \
+ && (defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx))
+
+#if defined(CONFIG_VIRTLAB2)
+#define PCMCIA_BOARD_MSG "Virtlab2"
+#elif defined(CONFIG_TQM8xxL)
+#define PCMCIA_BOARD_MSG "TQM8xxL"
+#elif defined(CONFIG_SVM_SC8xx)
+#define PCMCIA_BOARD_MSG "SC8xx"
+#endif
+
+#if defined(CONFIG_NSCU)
+
+#define power_config(slot) do {} while (0)
+#define power_off(slot) do {} while (0)
+#define power_on_5_0(slot) do {} while (0)
+#define power_on_3_3(slot) do {} while (0)
+
+#elif defined(CONFIG_HMI10)
+
+static inline void power_config(int slot)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ /*
+ * Configure Port B pins for
+ * 5 Volts Enable and 3 Volts enable
+ */
+ immap->im_cpm.cp_pbpar &= ~(0x00000300);
+}
+
+static inline void power_off(int slot)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ /* remove all power */
+ immap->im_cpm.cp_pbdat |= 0x00000300;
+}
+
+static inline void power_on_5_0(int slot)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ immap->im_cpm.cp_pbdat &= ~(0x0000100);
+ immap->im_cpm.cp_pbdir |= 0x00000300;
+}
+
+static inline void power_on_3_3(int slot)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ immap->im_cpm.cp_pbdat &= ~(0x0000200);
+ immap->im_cpm.cp_pbdir |= 0x00000300;
+}
+
+#elif defined(CONFIG_VIRTLAB2)
+
+#define power_config(slot) do {} while (0)
+static inline void power_off(int slot)
+{
+ volatile unsigned char *powerctl =
+ (volatile unsigned char *)PCMCIA_CTRL;
+ *powerctl = 0;
+}
+
+static inline void power_on_5_0(int slot)
+{
+ volatile unsigned char *powerctl =
+ (volatile unsigned char *)PCMCIA_CTRL;
+ *powerctl = 2; /* Enable 5V Vccout */
+}
+
+static inline void power_on_3_3(int slot)
+{
+ volatile unsigned char *powerctl =
+ (volatile unsigned char *)PCMCIA_CTRL;
+ *powerctl = 1; /* Enable 3.3V Vccout */
+}
+
+#else
+
+static inline void power_config(int slot)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ /*
+ * Configure Port C pins for
+ * 5 Volts Enable and 3 Volts enable
+ */
+ immap->im_ioport.iop_pcpar &= ~(0x0002 | 0x0004);
+ immap->im_ioport.iop_pcso &= ~(0x0002 | 0x0004);
+}
+
+static inline void power_off(int slot)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
+}
+
+static inline void power_on_5_0(int slot)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ immap->im_ioport.iop_pcdat |= 0x0004;
+ immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004);
+}
+
+static inline void power_on_3_3(int slot)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ immap->im_ioport.iop_pcdat |= 0x0002;
+ immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004);
+}
+
+#endif
+
+#ifdef CONFIG_HMI10
+static inline int check_card_is_absent(int slot)
+{
+ volatile pcmconf8xx_t *pcmp =
+ (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ return pcmp->pcmc_pipr & (0x10000000 >> (slot << 4));
+}
+#else
+static inline int check_card_is_absent(int slot)
+{
+ volatile pcmconf8xx_t *pcmp =
+ (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ return pcmp->pcmc_pipr & (0x18000000 >> (slot << 4));
+}
+#endif
+
+#ifdef NSCU_OE_INV
+#define NSCU_GCRX_CXOE 0
+#else
+#define NSCU_GCRX_CXOE __MY_PCMCIA_GCRX_CXOE
+#endif
+
+int pcmcia_hardware_enable(int slot)
+{
+ volatile pcmconf8xx_t *pcmp =
+ (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ volatile sysconf8xx_t *sysp =
+ (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+ uint reg, mask;
+
+ debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+ udelay(10000);
+
+ /*
+ * Configure SIUMCR to enable PCMCIA port B
+ * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+ */
+ sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
+
+ /* clear interrupt state, and disable interrupts */
+ pcmp->pcmc_pscr = PCMCIA_MASK(slot);
+ pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
+
+ /*
+ * Disable interrupts, DMA, and PCMCIA buffers
+ * (isolate the interface) and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= NSCU_GCRX_CXOE;
+
+ PCMCIA_PGCRX(slot) = reg;
+ udelay(500);
+
+ power_config(slot);
+ power_off(slot);
+
+ /*
+ * Make sure there is a card in the slot, then configure the interface.
+ */
+ udelay(10000);
+ debug ("[%d] %s: PIPR(%p)=0x%x\n", __LINE__,__FUNCTION__,
+ &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+
+ if (check_card_is_absent(slot)) {
+ printf (" No Card found\n");
+ return (1);
+ }
+
+ /*
+ * Power On.
+ */
+ mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+ reg = pcmp->pcmc_pipr;
+ debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+ reg,
+ (reg&PCMCIA_VS1(slot))?"n":"ff",
+ (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+ if ((reg & mask) == mask) {
+ power_on_5_0(slot);
+ puts (" 5.0V card found: ");
+ } else {
+ power_on_3_3(slot);
+ puts (" 3.3V card found: ");
+ }
+
+#if 0
+ /* VCC switch error flag, PCMCIA slot INPACK_ pin */
+ cp->cp_pbdir &= ~(0x0020 | 0x0010);
+ cp->cp_pbpar &= ~(0x0020 | 0x0010);
+ udelay(500000);
+#endif
+
+ udelay(1000);
+ debug ("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(slot);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ reg &= ~NSCU_GCRX_CXOE;
+
+ PCMCIA_PGCRX(slot) = reg;
+
+ udelay(250000); /* some cards need >150 ms to come up :-( */
+
+ debug ("# hardware_enable done\n");
+
+ return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+ u_long reg;
+
+ debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+
+ /* remove all power */
+ power_off(slot);
+
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = 0;
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= NSCU_GCRX_CXOE; /* active low */
+
+ PCMCIA_PGCRX(slot) = reg;
+
+ udelay(10000);
+
+ return (0);
+}
+#endif /* CFG_CMD_PCMCIA */
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+#ifndef CONFIG_NSCU
+ u_long reg;
+# ifdef DEBUG
+ volatile pcmconf8xx_t *pcmp =
+ (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+# endif
+
+ debug ("voltage_set: " PCMCIA_BOARD_MSG
+ " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+ 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+ /*
+ * Disable PCMCIA buffers (isolate the interface)
+ * and assert RESET signal
+ */
+ debug ("Disable PCMCIA buffers and assert RESET\n");
+ reg = PCMCIA_PGCRX(slot);
+ reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
+ reg |= NSCU_GCRX_CXOE; /* active low */
+
+ PCMCIA_PGCRX(slot) = reg;
+ udelay(500);
+
+ debug ("PCMCIA power OFF\n");
+ power_config(slot);
+ power_off(slot);
+
+ switch(vcc) {
+ case 0: break;
+ case 33: power_on_3_3(slot); break;
+ case 50: power_on_5_0(slot); break;
+ default: goto done;
+ }
+
+ /* Checking supported voltages */
+
+ debug("PIPR: 0x%x --> %s\n", pcmp->pcmc_pipr,
+ (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+ if (vcc)
+ debug("PCMCIA powered at %sV\n", (vcc == 50) ? "5.0" : "3.3");
+ else
+ debug("PCMCIA powered down\n");
+
+done:
+ debug("Enable PCMCIA buffers and stop RESET\n");
+ reg = PCMCIA_PGCRX(slot);
+ reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
+ reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
+ reg &= ~NSCU_GCRX_CXOE; /* active low */
+
+ PCMCIA_PGCRX(slot) = reg;
+ udelay(500);
+
+ debug("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", slot+'A');
+#endif /* CONFIG_NSCU */
+ return (0);
+}
+
+#endif /* CONFIG_PCMCIA && (CONFIG_TQM8xxL || CONFIG_SVM_SC8xx) */
diff --git a/include/405_mal.h b/include/405_mal.h
index 69d20c9..0598586 100644
--- a/include/405_mal.h
+++ b/include/405_mal.h
@@ -92,11 +92,21 @@
#define MAL_ESR_PBEI 0x00000001
/* ^^ ^^ */
/* Mal IER */
+#ifdef CONFIG_440SPE
+#define MAL_IER_PT 0x00000080
+#define MAL_IER_PRE 0x00000040
+#define MAL_IER_PWE 0x00000020
+#define MAL_IER_DE 0x00000010
+#define MAL_IER_OTE 0x00000004
+#define MAL_IER_OE 0x00000002
+#define MAL_IER_PE 0x00000001
+#else
#define MAL_IER_DE 0x00000010
#define MAL_IER_NE 0x00000008
#define MAL_IER_TE 0x00000004
#define MAL_IER_OPBE 0x00000002
#define MAL_IER_PLBE 0x00000001
+#endif
/* MAL Channel Active Set and Reset Registers */
#define MAL_TXRX_CASR (0x80000000)
diff --git a/include/asm-ppc/mmu.h b/include/asm-ppc/mmu.h
index 2606b79..baaf6f7 100644
--- a/include/asm-ppc/mmu.h
+++ b/include/asm-ppc/mmu.h
@@ -470,4 +470,45 @@
#define LAWAR_SIZE_1G (LAWAR_SIZE_BASE+19)
#define LAWAR_SIZE_2G (LAWAR_SIZE_BASE+20)
+#ifdef CONFIG_440SPE
+/*----------------------------------------------------------------------------+
+| Following instructions are not available in Book E mode of the GNU assembler.
++----------------------------------------------------------------------------*/
+#define DCCCI(ra,rb) .long 0x7c000000|\
+ (ra<<16)|(rb<<11)|(454<<1)
+
+#define ICCCI(ra,rb) .long 0x7c000000|\
+ (ra<<16)|(rb<<11)|(966<<1)
+
+#define DCREAD(rt,ra,rb) .long 0x7c000000|\
+ (rt<<21)|(ra<<16)|(rb<<11)|(486<<1)
+
+#define ICREAD(ra,rb) .long 0x7c000000|\
+ (ra<<16)|(rb<<11)|(998<<1)
+
+#define TLBSX(rt,ra,rb) .long 0x7c000000|\
+ (rt<<21)|(ra<<16)|(rb<<11)|(914<<1)
+
+#define TLBWE(rs,ra,ws) .long 0x7c000000|\
+ (rs<<21)|(ra<<16)|(ws<<11)|(978<<1)
+
+#define TLBRE(rt,ra,ws) .long 0x7c000000|\
+ (rt<<21)|(ra<<16)|(ws<<11)|(946<<1)
+
+#define TLBSXDOT(rt,ra,rb) .long 0x7c000001|\
+ (rt<<21)|(ra<<16)|(rb<<11)|(914<<1)
+
+#define MSYNC .long 0x7c000000|\
+ (598<<1)
+
+#define MBAR_INST .long 0x7c000000|\
+ (854<<1)
+
+/*----------------------------------------------------------------------------+
+| Following instruction is not available in PPC405 mode of the GNU assembler.
++----------------------------------------------------------------------------*/
+#define TLBRE(rt,ra,ws) .long 0x7c000000|\
+ (rt<<21)|(ra<<16)|(ws<<11)|(946<<1)
+
+#endif
#endif /* _PPC_MMU_H_ */
diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h
index 9ff03af..44b23f1 100644
--- a/include/asm-ppc/processor.h
+++ b/include/asm-ppc/processor.h
@@ -735,6 +735,8 @@
#define PVR_405EP_RB 0x51210950
#define PVR_440SP_RA 0x53221850
#define PVR_440SP_RB 0x53221891
+#define PVR_440SPe_RA 0x53421890
+#define PVR_440SPe_RB 0x53421891
#define PVR_601 0x00010000
#define PVR_602 0x00050000
#define PVR_603 0x00030000
diff --git a/include/bmp_logo.h b/include/bmp_logo.h
deleted file mode 100644
index 9c924b8..0000000
--- a/include/bmp_logo.h
+++ /dev/null
@@ -1,1948 +0,0 @@
-/*
- * Automatically generated by "tools/bmp_logo"
- *
- * DO NOT EDIT
- *
- */
-
-
-#ifndef __BMP_LOGO_H__
-#define __BMP_LOGO_H__
-
-#define BMP_LOGO_WIDTH 160
-#define BMP_LOGO_HEIGHT 96
-#define BMP_LOGO_COLORS 31
-#define BMP_LOGO_OFFSET 16
-
-unsigned short bmp_logo_palette[] = {
- 0x0343, 0x0454, 0x0565, 0x0565, 0x0676, 0x0787, 0x0898, 0x0999,
- 0x0AAA, 0x0ABA, 0x0BCB, 0x0CCC, 0x0DDD, 0x0EEE, 0x0FFF, 0x0FB3,
- 0x0FB4, 0x0FC4, 0x0FC5, 0x0FC6, 0x0FD7, 0x0FD8, 0x0FD9, 0x0FDA,
- 0x0FEA, 0x0FEB, 0x0FEC, 0x0FFD, 0x0FFE, 0x0FFF, 0x0FFF,
-};
-
-unsigned char bmp_logo_bitmap[] = {
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1B,
- 0x1B, 0x1B, 0x1B, 0x1B, 0x1B, 0x1B, 0x1B, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1B, 0x11, 0x10, 0x10, 0x10, 0x10,
- 0x14, 0x1E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x1B, 0x14, 0x10, 0x10, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1B, 0x14, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x14, 0x1C, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x22, 0x2A, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x29, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x14,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x18, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x18, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x12, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x19,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x18, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2D, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x28, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x1C, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x19, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x12, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1B, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x18,
- 0x2E, 0x2E, 0x2E, 0x16, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x18, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x16, 0x2E, 0x17, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x19, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2B, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2D, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x16, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x28, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x20, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x22, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x22, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x14, 0x17, 0x15, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x17, 0x1B, 0x2E, 0x1A, 0x14, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x17, 0x1B, 0x2E, 0x1B,
- 0x14, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x1B, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2D, 0x29,
- 0x23, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x23, 0x2A,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x14, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x14, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x1B, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x15, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x17, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x12, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x19, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2B, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x24, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x12, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x14, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x1B, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x1E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x1A, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1C, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x16, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x11, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x11, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1E, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x1E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x1A, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2B, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x28, 0x2E, 0x2A, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x29, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x1E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x19, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x1E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x11, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x21, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x12, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x1D, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x14, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x1B, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2A, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x14, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x1B, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x1B, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x23, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x20, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x22, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x18, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x23, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x23, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2A, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x1E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x21, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2D, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x1E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x12, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x1D, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x18, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x1D, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x22, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x20, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x16, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2D, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1D, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x1C, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x1C, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x1E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x16, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x11, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x1E, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x16, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2D, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x21, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x24, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x1D, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x14, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x11, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x18,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x15, 0x2E, 0x2E, 0x2E, 0x19,
- 0x12, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x11, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x1E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x1B, 0x2E, 0x2E, 0x1B, 0x16, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x19, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2D, 0x26,
- 0x22, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x22, 0x27,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x13, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x16, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x19, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2D, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2D, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x12, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x1C, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2A, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x20, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x13, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x2C, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2D, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x11, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x1C, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1C,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x11, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x12, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x1E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x1F, 0x2A, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2B, 0x1F, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x13, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x1B,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1D, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x12, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x20,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1A, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x11, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x15, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x1F,
- 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x2D, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x29, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F, 0x1F,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x17, 0x14, 0x10, 0x11, 0x14,
- 0x1A, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1B, 0x17, 0x17, 0x1A, 0x1B, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2B, 0x26,
- 0x2A, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2A, 0x26,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x17, 0x1B, 0x1B, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x16, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10,
- 0x1E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x12, 0x10, 0x10, 0x14, 0x14, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x16,
- 0x10, 0x10, 0x14, 0x14, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x12, 0x10, 0x1B, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x17, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x13, 0x14, 0x13, 0x10, 0x10, 0x1C, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1B, 0x10, 0x2E,
- 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x18, 0x10, 0x10, 0x17, 0x14, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x16, 0x10,
- 0x16, 0x2E, 0x2E, 0x2E, 0x2E, 0x16, 0x10, 0x11,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x19, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1B, 0x10, 0x10,
- 0x1D, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x12,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x10, 0x10, 0x19, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x15,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1B, 0x10, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1B, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x15, 0x10, 0x10, 0x10,
- 0x1D, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x1B,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x14, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x10,
- 0x19, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x10,
- 0x1B, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1E,
- 0x10, 0x10, 0x10, 0x17, 0x17, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1B, 0x10, 0x1B,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x16, 0x10, 0x1E, 0x12, 0x10,
- 0x2E, 0x2E, 0x2E, 0x18, 0x10, 0x2E, 0x17, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x16, 0x10,
- 0x1C, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1B, 0x10, 0x1B,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x15, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x17,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x14, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1B, 0x10, 0x1B,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x14,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10, 0x11, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x17, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x13, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x17,
- 0x10, 0x10, 0x10, 0x18, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1B, 0x10, 0x1B,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x17, 0x10, 0x10, 0x10, 0x10, 0x10, 0x19,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x17, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x17, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x13, 0x10, 0x1A, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x1E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x19, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x19, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x10, 0x10, 0x10, 0x10, 0x10, 0x1C, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x16, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x15, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x17,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x1E, 0x10, 0x12, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x12,
- 0x11, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x1C, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1A, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x10, 0x1C,
- 0x2E, 0x2E, 0x2E, 0x1B, 0x10, 0x16, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x16, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x1A, 0x2E,
- 0x2E, 0x1D, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x14, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1E, 0x10, 0x19, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1A, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x13,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x17, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x13, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x17, 0x10, 0x1C, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x14, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x11, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x14,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x18,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x1D, 0x10, 0x15, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x14, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x19, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x14, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x19, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x14, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10,
- 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1A, 0x10,
- 0x14, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x1B, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x1C, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x14, 0x10, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x1A, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x1C, 0x10, 0x10, 0x10, 0x10, 0x10, 0x13, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x13, 0x10, 0x10, 0x10, 0x10, 0x10, 0x16, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x17, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x13, 0x10,
- 0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x11, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x1E, 0x10, 0x16, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x1A, 0x10, 0x19, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x11, 0x10, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x10, 0x10, 0x10, 0x11, 0x14,
- 0x10, 0x10, 0x10, 0x17, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x2E,
- 0x2E, 0x2E, 0x2E, 0x2E, 0x2E, 0x16, 0x10, 0x10,
- 0x10, 0x14, 0x13, 0x10, 0x10, 0x10, 0x2E, 0x2E,
-
-};
-
-#endif /* __BMP_LOGO_H__ */
diff --git a/include/common.h b/include/common.h
index 5d8b156..9a19001 100644
--- a/include/common.h
+++ b/include/common.h
@@ -116,12 +116,13 @@
/*
* enable common handling for all TQM8xxL/M boards:
- * - CONFIG_TQM8xxM will be defined for all TQM8xxM boards
+ * - CONFIG_TQM8xxM will be defined for all TQM8xxM and TQM885D boards
* - CONFIG_TQM8xxL will be defined for all TQM8xxL _and_ TQM8xxM boards
*/
#if defined(CONFIG_TQM823M) || defined(CONFIG_TQM850M) || \
defined(CONFIG_TQM855M) || defined(CONFIG_TQM860M) || \
- defined(CONFIG_TQM862M) || defined(CONFIG_TQM866M)
+ defined(CONFIG_TQM862M) || defined(CONFIG_TQM866M) || \
+ defined(CONFIG_TQM885D)
# ifndef CONFIG_TQM8xxM
# define CONFIG_TQM8xxM
# endif
@@ -244,6 +245,9 @@
void pci_master_init (struct pci_controller *);
# endif
int is_pci_host (struct pci_controller *);
+#if defined(CONFIG_440SPE)
+ void pcie_setup_hoses(void);
+#endif
#endif
int misc_init_f (void);
@@ -458,6 +462,11 @@
#if defined(CONFIG_4xx) || defined(CONFIG_IOP480)
# if defined(CONFIG_440)
typedef PPC440_SYS_INFO sys_info_t;
+# if defined(CONFIG_440SPE)
+ unsigned long determine_sysper(void);
+ unsigned long determine_pci_clock_per(void);
+ int ppc440spe_revB(void);
+# endif
# else
typedef PPC405_SYS_INFO sys_info_t;
# endif
@@ -594,7 +603,7 @@
#endif
#ifdef CONFIG_INIT_CRITICAL
-#error CONFIG_INIT_CRITICAL is depracted!
+#error CONFIG_INIT_CRITICAL is deprecated!
#error Read section CONFIG_SKIP_LOWLEVEL_INIT in README.
#endif
diff --git a/include/commproc.h b/include/commproc.h
index 061468e..12400e3 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -1405,15 +1405,16 @@
#endif /* CONFIG_SXNI855T */
-/*** MVS1, TQM823L/M, TQM850L/M, ETX094, R360MPI *******************/
+/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, ETX094, R360MPI **********/
#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
defined(CONFIG_R360MPI) || defined(CONFIG_RBC823) || \
defined(CONFIG_TQM823L) || defined(CONFIG_TQM823M) || \
defined(CONFIG_TQM850L) || defined(CONFIG_TQM850M) || \
- defined(CONFIG_ETX094) || defined(CONFIG_RRVISION)|| \
- defined(CONFIG_VIRTLAB2)|| \
+ defined(CONFIG_TQM885D) || defined(CONFIG_ETX094) || \
+ defined(CONFIG_RRVISION)|| defined(CONFIG_VIRTLAB2)|| \
(defined(CONFIG_LANTEC) && CONFIG_LANTEC < 2)
+
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
*/
@@ -1438,6 +1439,11 @@
*/
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002600)
+
+# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
+#define FEC_ENET
+# endif /* CONFIG_FEC_ENET */
+
#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */
/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/
diff --git a/include/configs/CPU87.h b/include/configs/CPU87.h
index 9a98e5c..7a1dada 100644
--- a/include/configs/CPU87.h
+++ b/include/configs/CPU87.h
@@ -455,7 +455,7 @@
#define CFG_MIN_AM_MASK 0xC0000000
/*
- * we use the same values for 32 MB and 128 MB SDRAM
+ * we use the same values for 32 MB, 128 MB and 256 MB SDRAM
* refresh rate = 7.68 uS (100 MHz Bus Clock)
*/
@@ -510,6 +510,24 @@
PSDMR_WRC_1C |\
PSDMR_CL_2)
+ /* SDRAM initialization values for 10-column chips
+ */
+#define CFG_OR2_10COL (CFG_MIN_AM_MASK |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A4 |\
+ ORxS_NUMR_13)
+
+#define CFG_PSDMR_10COL (PSDMR_PBI |\
+ PSDMR_SDAM_A17_IS_A5 |\
+ PSDMR_BSMA_A13_A15 |\
+ PSDMR_SDA10_PBI1_A6 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_1C |\
+ PSDMR_CL_2)
+
/*
* Init Memory Controller:
*
@@ -588,9 +606,9 @@
BRx_MS_SDRAM_P |\
BRx_V)
-#define CFG_OR2_PRELIM CFG_OR2_9COL
+#define CFG_OR2_PRELIM CFG_OR2_8COL
-#define CFG_PSDMR CFG_PSDMR_9COL
+#define CFG_PSDMR CFG_PSDMR_8COL
#endif /* CFG_RAMBOOT */
/* Bank 3 - Dual Ported SRAM
diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h
new file mode 100644
index 0000000..8a6e5a6
--- /dev/null
+++ b/include/configs/TB5200.h
@@ -0,0 +1,507 @@
+/*
+ * (C) Copyright 2003-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004-2006
+ * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
+#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
+#define CONFIG_TB5200 1 /* ... on a TB5200 base board */
+
+#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Serial console configuration
+ */
+#define CONFIG_PSC_CONSOLE 1 /* default console is on PSC1 */
+#define CONFIG_SERIAL_MULTI 1 /* support multiple consoles */
+#define CONFIG_PSC_CONSOLE2 6 /* second console is on PSC6 */
+#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * Video console
+ */
+#if 1
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_SM501
+#define CONFIG_VIDEO_SM501_32BPP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_SPLASH_SCREEN
+#define CFG_CONSOLE_IS_IN_ENV
+#endif
+
+#ifdef CONFIG_VIDEO
+#define ADD_BMP_CMD CFG_CMD_BMP
+#else
+#define ADD_BMP_CMD 0
+#endif
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+/* USB */
+#define CONFIG_USB_OHCI
+#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
+#define CONFIG_USB_STORAGE
+
+/* POST support */
+#define CONFIG_POST (CFG_POST_MEMORY | \
+ CFG_POST_CPU | \
+ CFG_POST_I2C)
+
+#ifdef CONFIG_POST
+#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
+/* preserve space for the post_word at end of on-chip SRAM */
+#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
+#else
+#define CFG_CMD_POST_DIAG 0
+#endif
+
+/* IDE */
+#define ADD_IDE_CMD (CFG_CMD_IDE | CFG_CMD_FAT | CFG_CMD_EXT2)
+
+/*
+ * Supported commands
+ */
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ ADD_BMP_CMD | \
+ ADD_IDE_CMD | \
+ ADD_PCI_CMD | \
+ ADD_USB_CMD | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_ECHO | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_I2C | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_MII | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PING | \
+ CFG_CMD_POST_DIAG | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_SNTP | \
+ CFG_CMD_BSP)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_TIMESTAMP /* display image timestamps */
+
+#if (TEXT_BASE == 0xFC000000) /* Boot low */
+# define CFG_LOWBOOT 1
+#endif
+
+/*
+ * Autobooting
+ */
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#if defined(CONFIG_TQM5200_B)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "bootfile=/tftpboot/tqm5200/uImage\0" \
+ "load=tftp 200000 ${u-boot}\0" \
+ "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
+ "update=protect off FC000000 FC07FFFF;" \
+ "erase FC000000 FC07FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC07FFFF\0" \
+ ""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "bootfile=/tftpboot/tqm5200/uImage\0" \
+ "load=tftp 200000 $(u-boot)\0" \
+ "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
+ "update=protect off FC000000 FC05FFFF;" \
+ "erase FC000000 FC05FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC05FFFF\0" \
+ ""
+#endif /* CONFIG_TQM5200_B */
+
+#define CONFIG_BOOTCOMMAND "run net_nfs"
+
+/*
+ * IPB Bus clocking configuration.
+ */
+#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+
+#if defined(CFG_IPBSPEED_133)
+/*
+ * PCI Bus clocking configuration
+ *
+ * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
+ * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
+ * been tested with a IPB Bus Clock of 66 MHz.
+ */
+#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#endif
+
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CFG_I2C_MODULE 2 /* Select I2C module #2 */
+
+/*
+ * I2C clock frequency
+ *
+ * Please notice, that the resulting clock frequency could differ from the
+ * configured value. This is because the I2C clock is derived from system
+ * clock over a frequency divider with only a few divider values. U-boot
+ * calculates the best approximation for CFG_I2C_SPEED. However the calculated
+ * approximation allways lies below the configured value, never above.
+ */
+#define CFG_I2C_SPEED 100000 /* 100 kHz */
+#define CFG_I2C_SLAVE 0x7F
+
+/*
+ * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
+ * also). For other EEPROMs configuration should be verified. On Mini-FAP the
+ * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
+ * same configuration could be used.
+ */
+#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
+
+/* List of I2C addresses to be verified by POST */
+#undef I2C_ADDR_LIST
+#define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \
+ CFG_I2C_RTC_ADDR, \
+ CFG_I2C_SLAVE }
+
+/*
+ * Flash configuration
+ */
+#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */
+
+/* use CFI flash driver */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */
+#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#define CFG_FLASH_USE_BUFFER_WRITE 1
+
+#if !defined(CFG_LOWBOOT)
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000)
+#else /* CFG_LOWBOOT */
+#if defined(CONFIG_TQM5200_B)
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00080000)
+#else
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000)
+#endif /* CONFIG_TQM5200_B */
+#endif /* CFG_LOWBOOT */
+#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
+ (= chip selects) */
+
+/* Dynamic MTD partition support */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=TQM5200-0"
+#if defined(CONFIG_TQM5200_B)
+#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:768k(firmware)," \
+ "1280k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "16m(big-fs)," \
+ "8m(misc)"
+#else
+#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
+ "1408k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "16m(big-fs)," \
+ "8m(misc)"
+#endif /* CONFIG_TQM5200_B */
+
+/*
+ * Environment settings
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SIZE 0x10000
+#if defined(CONFIG_TQM5200_B)
+#define CFG_ENV_SECT_SIZE 0x40000
+#else
+#define CFG_ENV_SECT_SIZE 0x20000
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#endif /* CONFIG_TQM5200_B */
+
+/*
+ * Memory map
+ */
+#define CFG_MBAR 0xF0000000
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_DEFAULT_MBAR 0x80000000
+
+/* Use ON-Chip SRAM until RAM will be available */
+#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
+#ifdef CONFIG_POST
+/* preserve space for the post_word at end of on-chip SRAM */
+#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
+#else
+#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE
+#endif
+
+
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_BASE TEXT_BASE
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+# define CFG_RAMBOOT 1
+#endif
+
+#if defined(CONFIG_TQM5200_B)
+#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#endif /* CONFIG_TQM5200_B */
+#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Ethernet configuration
+ */
+#define CONFIG_MPC5xxx_FEC 1
+/*
+ * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ */
+/* #define CONFIG_FEC_10MBIT 1 */
+#define CONFIG_PHY_ADDR 0x00
+
+/*
+ * GPIO configuration
+ *
+ * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
+ * Bit 0 (mask: 0x80000000): 1
+ * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
+ * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
+ * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
+ * Use for REV200 STK52XX boards. Do not use with REV100 modules
+ * (because, there I2C1 is used as I2C bus)
+ * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
+ * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
+ * 000 -> All PSC2 pins are GIOPs
+ * 001 -> CAN1/2 on PSC2 pins
+ * Use for REV100 STK52xx boards
+ * use PSC3: Bits 20:23 (mask: 0x00000300):
+ * 0001 -> USB2
+ * 0000 -> GPIO
+ * use PSC6:
+ * on STK52xx:
+ * use as UART. Pins PSC6_0 to PSC6_3 are used.
+ * Bits 9:11 (mask: 0x00700000):
+ * 101 -> PSC6 : Extended POST test is not available
+ * on MINI-FAP and TQM5200_IB:
+ * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
+ * 000 -> PSC6 could not be used as UART, CODEC or IrDA
+ * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
+ * tests.
+ */
+#define CFG_GPS_PORT_CONFIG 0x81500114
+
+/*
+ * RTC configuration
+ */
+#define CONFIG_RTC_M41T11 1
+#define CFG_I2C_RTC_ADDR 0x68
+#define CFG_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
+ year */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+/* Enable an alternate, more extensive memory test */
+#define CFG_ALT_MEMTEST
+
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+/*
+ * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
+ * which is normally part of the default commands (CFV_CMD_DFL)
+ */
+#define CONFIG_LOOPW
+
+/*
+ * Various low-level settings
+ */
+#if defined(CONFIG_MPC5200)
+#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
+#define CFG_HID0_FINAL HID0_ICE
+#else
+#define CFG_HID0_INIT 0
+#define CFG_HID0_FINAL 0
+#endif
+
+#define CFG_BOOTCS_START CFG_FLASH_BASE
+#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
+#ifdef CFG_PCISPEED_66
+#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
+#else
+#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
+#endif
+#define CFG_CS0_START CFG_FLASH_BASE
+#define CFG_CS0_SIZE CFG_FLASH_SIZE
+
+#define CONFIG_LAST_STAGE_INIT
+
+/*
+ * SRAM - Do not map below 2 GB in address space, because this area is used
+ * for SDRAM autosizing.
+ */
+#define CFG_CS2_START 0xE5000000
+#define CFG_CS2_SIZE 0x100000 /* 1 MByte */
+#define CFG_CS2_CFG 0x0004D930
+
+/*
+ * Grafic controller - Do not map below 2 GB in address space, because this
+ * area is used for SDRAM autosizing.
+ */
+#define SM501_FB_BASE 0xE0000000
+#define CFG_CS1_START (SM501_FB_BASE)
+#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
+#define CFG_CS1_CFG 0x8F48FF70
+#define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000
+
+#define CFG_CS_BURST 0x00000000
+#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
+
+#define CFG_RESET_ADDRESS 0xff000000
+
+/*-----------------------------------------------------------------------
+ * USB stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_USB_CLOCK 0x0001BBBB
+#define CONFIG_USB_CONFIG 0x00001000
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CONFIG_IDE_RESET /* reset for ide supported */
+#define CONFIG_IDE_PREINIT
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (0x0060)
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET (0x005C)
+
+/* Interval between registers */
+#define CFG_ATA_STRIDE 4
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 6b8759f..31e3eed 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -2,7 +2,7 @@
* (C) Copyright 2003-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
- * (C) Copyright 2004-2005
+ * (C) Copyright 2004-2006
* Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
*
* See file CREDITS for list of people who contributed to this
@@ -32,29 +32,47 @@
* (easy to change)
*/
-#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
-#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
-#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
-#define CONFIG_STK52XX 1 /* ... on a STK52XX base board */
+#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
+#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
+#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+/* On a Cameron or on a FO300 board or ... */
+#if !defined(CONFIG_CAM5200) && !defined(CONFIG_FO300)
+#define CONFIG_STK52XX 1 /* ... on a STK52XX board */
+#endif
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Serial console configuration
*/
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#ifdef CONFIG_FO300
+#define CFG_DEVICE_NULLDEV 1 /* enable null device */
+#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* used to detect S1 switch position */
+
+#if 0
+#define FO300_SILENT_CONSOLE_WHEN_S1_CLOSED 1 /* silent console on PSC1 when S1 */
+ /* switch is closed */
+#endif
+
+#undef FO300_SILENT_CONSOLE_WHEN_S1_CLOSED /* silent console on PSC1 when S1 */
+ /* switch is open */
+#endif /* CONFIG_FO300 */
+
#ifdef CONFIG_STK52XX
#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
@@ -96,18 +114,24 @@
/*
* Video console
*/
-#if 1
+#ifndef CONFIG_TQM5200S /* No graphics controller on TQM5200S */
#define CONFIG_VIDEO
#define CONFIG_VIDEO_SM501
#define CONFIG_VIDEO_SM501_32BPP
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
+
+#ifndef CONFIG_FO300
#define CONFIG_CONSOLE_EXTRA_INFO
+#else
+#define CONFIG_VIDEO_BMP_LOGO
+#endif
+
+#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_SPLASH_SCREEN
#define CFG_CONSOLE_IS_IN_ENV
-#endif
+#endif /* #ifndef CONFIG_TQM5200S */
#ifdef CONFIG_VIDEO
#define ADD_BMP_CMD CFG_CMD_BMP
@@ -121,7 +145,7 @@
#define CONFIG_ISO_PARTITION
/* USB */
-#ifdef CONFIG_STK52XX
+#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
#define CONFIG_USB_OHCI
#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
@@ -129,10 +153,12 @@
#define ADD_USB_CMD 0
#endif
+#ifndef CONFIG_CAM5200
/* POST support */
#define CONFIG_POST (CFG_POST_MEMORY | \
CFG_POST_CPU | \
CFG_POST_I2C)
+#endif
#ifdef CONFIG_POST
#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
@@ -143,7 +169,7 @@
#endif
/* IDE */
-#if defined (CONFIG_MINIFAP) || defined (CONFIG_STK52XX)
+#if defined (CONFIG_MINIFAP) || defined (CONFIG_STK52XX) || defined(CONFIG_FO300)
#define ADD_IDE_CMD (CFG_CMD_IDE | CFG_CMD_FAT | CFG_CMD_EXT2)
#else
#define ADD_IDE_CMD 0
@@ -176,8 +202,8 @@
#define CONFIG_TIMESTAMP /* display image timestamps */
-#if (TEXT_BASE == 0xFC000000) /* Boot low */
-# define CFG_LOWBOOT 1
+#if (TEXT_BASE != 0xFFF00000)
+# define CFG_LOWBOOT 1 /* Boot low */
#endif
/*
@@ -186,11 +212,49 @@
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
+#ifdef CONFIG_STK52XX
+# if defined(CONFIG_TQM5200_B)
+# if defined(CFG_LOWBOOT)
+# define ENV_UPDT \
+ "update=protect off FC000000 FC07FFFF;" \
+ "erase FC000000 FC07FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC07FFFF\0"
+# else /* highboot */
+# define ENV_UPDT \
+ "update=protect off FFF00000 FFF7FFFF;" \
+ "erase FFF00000 FFF7FFFF;" \
+ "cp.b 200000 FFF00000 ${filesize};" \
+ "protect on FFF00000 FFF7FFFF\0"
+# endif /* CFG_LOWBOOT */
+# else /* !CONFIG_TQM5200_B */
+# define ENV_UPDT \
+ "update=protect off FC000000 FC05FFFF;" \
+ "erase FC000000 FC05FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC05FFFF\0"
+# endif /* CONFIG_TQM5200_B */
+#elif defined (CONFIG_CAM5200)
+# define ENV_UPDT \
+ "update=protect off FC000000 FC03FFFF;" \
+ "erase FC000000 FC03FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC03FFFF\0"
+#elif defined (CONFIG_FO300)
+# define ENV_UPDT \
+ "update=protect off FC000000 FC05FFFF;" \
+ "erase FC000000 FC05FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC05FFFF\0"
+#else
+# error "Unknown Carrier Board"
+#endif /* CONFIG_STK52XX */
+
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
@@ -200,18 +264,18 @@
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
- "flash_self=run ramargs addip;" \
+ "addcons=setenv bootargs ${bootargs} " \
+ "console=ttyS0,${baudrate}\0" \
+ "flash_self=run ramargs addip addcons;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_nfs=run nfsargs addip;" \
+ "flash_nfs=run nfsargs addip addcons;" \
"bootm ${kernel_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \
+ "bootm\0" \
"bootfile=/tftpboot/tqm5200/uImage\0" \
- "load=tftp 200000 ${u-boot}\0" \
"u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
- "update=protect off FC000000 FC05FFFF;" \
- "erase FC000000 FC05FFFF;" \
- "cp.b 200000 FC000000 ${filesize};" \
- "protect on FC000000 FC05FFFF\0" \
+ "load=tftp 200000 ${u-boot}\0" \
+ ENV_UPDT \
""
#define CONFIG_BOOTCOMMAND "run net_nfs"
@@ -283,45 +347,87 @@
/*
* Flash configuration
*/
-#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */
+#define CFG_FLASH_BASE 0xFC000000
-/* use CFI flash driver if no module variant is spezified */
+/* use CFI flash driver */
#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START }
#define CFG_FLASH_EMPTY_INFO
#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */
#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
+#define CFG_FLASH_USE_BUFFER_WRITE 1
-#if !defined(CFG_LOWBOOT)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000)
-#else /* CFG_LOWBOOT */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000)
-#endif /* CFG_LOWBOOT */
+#if defined (CONFIG_CAM5200)
+# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00040000)
+#elif defined(CONFIG_TQM5200_B)
+# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00080000)
+#else
+# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000)
+#endif
+
#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
(= chip selects) */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
/* Dynamic MTD partition support */
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT "nor0=TQM5200-0"
-#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
+
+#ifdef CONFIG_STK52XX
+# if defined(CONFIG_TQM5200_B)
+# if defined(CFG_LOWBOOT)
+# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:1m(firmware)," \
+ "1536k(kernel)," \
+ "3584k(small-fs)," \
+ "2m(initrd)," \
+ "8m(misc)," \
+ "16m(big-fs)"
+# else /* highboot */
+# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:2560k(kernel)," \
+ "3584k(small-fs)," \
+ "2m(initrd)," \
+ "8m(misc)," \
+ "15m(big-fs)," \
+ "1m(firmware)"
+# endif /* CFG_LOWBOOT */
+# else /* !CONFIG_TQM5200_B */
+# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
"1408k(kernel)," \
"2m(initrd)," \
"4m(small-fs)," \
- "16m(big-fs)," \
- "8m(misc)"
+ "8m(misc)," \
+ "16m(big-fs)"
+# endif /* CONFIG_TQM5200_B */
+#elif defined (CONFIG_CAM5200)
+# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:768k(firmware)," \
+ "1792k(kernel)," \
+ "3584k(small-fs)," \
+ "2m(initrd)," \
+ "8m(misc)," \
+ "16m(big-fs)"
+#elif defined (CONFIG_FO300)
+# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
+ "1408k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "8m(misc)," \
+ "16m(big-fs)"
+#else
+# error "Unknown Carrier Board"
+#endif /* CONFIG_STK52XX */
/*
* Environment settings
*/
#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x10000
+#define CFG_ENV_SIZE 0x4000 /* 16 k - keep small for fast booting */
+#if defined(CONFIG_TQM5200_B)
+#define CFG_ENV_SECT_SIZE 0x40000
+#else
#define CFG_ENV_SECT_SIZE 0x20000
+#endif /* CONFIG_TQM5200_B */
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
/*
* Memory map
@@ -349,8 +455,15 @@
# define CFG_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
+#if defined (CONFIG_CAM5200)
+# define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#elif defined(CONFIG_TQM5200_B)
+# define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
+#else
+# define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#endif
+
+#define CFG_MALLOC_LEN (1024 << 10) /* Reserve 1024 kB for malloc() */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
@@ -371,15 +484,18 @@
* use ALT CAN position: Bits 2-3 (mask: 0x30000000):
* 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
* 01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
- * Use for REV200 STK52XX boards. Do not use with REV100 modules
- * (because, there I2C1 is used as I2C bus)
+ * Use for REV200 STK52XX boards and FO300 boards. Do not use
+ * with REV100 modules (because, there I2C1 is used as I2C bus)
* use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
* use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
* 000 -> All PSC2 pins are GIOPs
* 001 -> CAN1/2 on PSC2 pins
* Use for REV100 STK52xx boards
+ * 01x -> Use AC97
+ * use PSC3: Bits 20-23 (mask: 0x00000f00)
+ * 1100 -> UART/SPI (on FO300 board)
* use PSC6:
- * on STK52xx:
+ * on STK52xx and FO300:
* use as UART. Pins PSC6_0 to PSC6_3 are used.
* Bits 9:11 (mask: 0x00700000):
* 101 -> PSC6 : Extended POST test is not available
@@ -401,6 +517,8 @@
# define CFG_GPS_PORT_CONFIG 0x91500004
# endif
# endif
+#elif defined (CONFIG_FO300)
+# define CFG_GPS_PORT_CONFIG 0x91502c24
#else /* TMQ5200 Inbetriebnahme-Board */
# define CFG_GPS_PORT_CONFIG 0x81000004
#endif
@@ -411,6 +529,8 @@
#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100)
# define CONFIG_RTC_M41T11 1
# define CFG_I2C_RTC_ADDR 0x68
+# define CFG_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
+ year */
#else
# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
#endif
@@ -420,6 +540,10 @@
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
+#define CFG_PROMPT_HUSH_PS2 "> "
+
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
@@ -466,32 +590,25 @@
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
-/* automatic configuration of chip selects */
-#ifdef CONFIG_CS_AUTOCONF
#define CONFIG_LAST_STAGE_INIT
-#endif
/*
* SRAM - Do not map below 2 GB in address space, because this area is used
* for SDRAM autosizing.
*/
-#if defined (CONFIG_CS_AUTOCONF)
#define CFG_CS2_START 0xE5000000
#define CFG_CS2_SIZE 0x100000 /* 1 MByte */
#define CFG_CS2_CFG 0x0004D930
-#endif
/*
* Grafic controller - Do not map below 2 GB in address space, because this
* area is used for SDRAM autosizing.
*/
-#if defined (CONFIG_CS_AUTOCONF)
#define SM501_FB_BASE 0xE0000000
#define CFG_CS1_START (SM501_FB_BASE)
#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
#define CFG_CS1_CFG 0x8F48FF70
#define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000
-#endif
#define CFG_CS_BURST 0x00000000
#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index cec7e3e..92c7016 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -422,9 +422,9 @@
#define CFG_SICRL SICRL_LDP_A
/* i-cache and d-cache disabled */
-#define CFG_HID0_INIT 0x000000000
-#define CFG_HID0_FINAL CFG_HID0_INIT
-#define CFG_HID2 0x000000000
+#define CFG_HID0_INIT 0x000000000
+#define CFG_HID0_FINAL CFG_HID0_INIT
+#define CFG_HID2 HID2_HBE
/* DDR 0 - 512M */
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
@@ -437,12 +437,21 @@
#define CFG_IBAT2U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
/* PCI */
-#define CFG_IBAT3L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#ifdef CONFIG_PCI
+#define CFG_IBAT3L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT3U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L (CFG_PCI1_MEM_BASE + 0x10000000 | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT4L (CFG_PCI1_MEM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT4U (CFG_PCI1_MEM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_IBAT5L (CFG_PCI1_IO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_IBAT5U (CFG_PCI1_IO_BASE + 0x10000000 | BATU_BL_16M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT3L (0)
+#define CFG_IBAT3U (0)
+#define CFG_IBAT4L (0)
+#define CFG_IBAT4U (0)
+#define CFG_IBAT5L (0)
+#define CFG_IBAT5U (0)
+#endif
/* IMMRBAR */
#define CFG_IBAT6L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index da6946b..bc3b9aa 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -158,7 +158,7 @@
#undef CONFIG_CONS_NONE /* define if console on something else */
#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-#else
+#else /* ! TQM8560 */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
@@ -170,6 +170,15 @@
#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+/* PS/2 Keyboard */
+#if !defined(CONFIG_TQM8560)
+#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
+#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
+#define CONFIG_PS2SERIAL 2 /* .. on DUART2 */
+#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
+#define CONFIG_BOARD_EARLY_INIT_R 1
+#endif /* !CONFIG_TQM8560 */
+
#endif /* CONFIG_TQM8560 */
#define CONFIG_BAUDRATE 115200
@@ -177,13 +186,6 @@
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-/* PS/2 Keyboard */
-#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
-#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
-#define CONFIG_PS2SERIAL 2 /* .. on DUART2 */
-#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
-#define CONFIG_BOARD_EARLY_INIT_R 1
-
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
@@ -422,7 +424,7 @@
#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
@@ -447,7 +449,7 @@
"run nfsargs addip addcons;bootm\0" \
"rootpath=/opt/eldk/ppc_85xx\0" \
"kernel_addr=FE000000\0" \
- "ramdisk_addr=FE100000\0" \
+ "ramdisk_addr=FE180000\0" \
"load=tftp 100000 /tftpboot/$hostname/u-boot.bin\0" \
"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
"cp.b 100000 fffc0000 40000;" \
diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
new file mode 100644
index 0000000..ede4e3b
--- /dev/null
+++ b/include/configs/TQM885D.h
@@ -0,0 +1,492 @@
+/*
+ * (C) Copyright 2000-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2006
+ * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC885 1 /* This is a MPC885 CPU */
+#define CONFIG_TQM885D 1 /* ...on a TQM88D module */
+
+#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz - PLL input clock */
+#define CFG_8xx_CPUCLK_MIN 15000000 /* 15 MHz - CPU minimum clock */
+#define CFG_8xx_CPUCLK_MAX 133000000 /* 133 MHz - CPU maximum clock */
+#define CONFIG_8xx_CPUCLK_DEFAULT 66000000 /* 50 MHz - CPU default clock */
+ /* (it will be used if there is no */
+ /* 'cpuclk' variable with valid value) */
+
+#define CFG_MEASURE_CPUCLK /* Measure real cpu clock */
+ /* (function measure_gclk() */
+ /* will be called) */
+#ifdef CFG_MEASURE_CPUCLK
+#define CFG_8XX_XIN 10000000 /* measure_gclk() needs this */
+#endif
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+
+#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
+
+#define CONFIG_BOOTCOUNT_LIMIT
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_BOARD_TYPES 1 /* support board types */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "rootpath=/opt/eldk/ppc_8xx\0" \
+ "bootfile=/tftpboot/TQM866M/uImage\0" \
+ "kernel_addr=40080000\0" \
+ "ramdisk_addr=40180000\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+
+#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
+
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+
+#define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */
+#define CFG_I2C_SLAVE 0xFE
+
+#ifdef CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL 0x00000020 /* PB 26 */
+#define PB_SDA 0x00000010 /* PB 27 */
+
+#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
+#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
+#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
+#endif /* CONFIG_SOFT_I2C */
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C?? */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* two byte address */
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+# define CONFIG_RTC_DS1337 1
+# define CFG_I2C_RTC_ADDR 0x68
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#undef CONFIG_RTC_MPC8xx /* MPC866 does not support RTC */
+
+#define CONFIG_TIMESTAMP /* but print image timestmps */
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IDE | \
+ CFG_CMD_MII | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PING )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if 0
+#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
+#endif
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0300000 /* 1 ... 3 MB in DRAM */
+#define CFG_ALT_MEMTEST /* alternate, more extensive
+ memory test.*/
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Enable loopw commando. This has only effect, if CFG_CMD_MEM is defined,
+ * which is normally part of the default commands (CFV_CMD_DFL)
+ */
+#define CONFIG_LOOPW
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x40000000
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Hardware Information Block
+ */
+#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
+#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
+#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#ifndef CONFIG_CAN_DRIVER
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#else /* we must activate GPL5 in the SIUMCR for CAN */
+#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#endif /* CONFIG_CAN_DRIVER */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
+
+/*
+ * FLASH timing: Default value of OR0 after reset
+ */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
+ OR_SCY_6_CLK | OR_TRLX)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+
+#define CFG_OR1_REMAP CFG_OR0_REMAP
+#define CFG_OR1_PRELIM CFG_OR0_PRELIM
+#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
+
+/*
+ * BR2/3 and OR2/3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
+#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
+#define SDRAM_MAX_SIZE (256 << 20) /* max 256 MB per bank */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CFG_OR_TIMING_SDRAM 0x00000A00
+
+#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+#ifndef CONFIG_CAN_DRIVER
+#define CFG_OR3_PRELIM CFG_OR2_PRELIM
+#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
+#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
+#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
+#define CFG_OR3_CAN (CFG_CAN_OR_AM | OR_G5LA | OR_BI)
+#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) | \
+ BR_PS_8 | BR_MS_UPMB | BR_V )
+#endif /* CONFIG_CAN_DRIVER */
+
+/*
+ * 4096 Rows from SDRAM example configuration
+ * 1000 factor s -> ms
+ * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4 Number of refresh cycles per period
+ * 64 Refresh cycle in ms per number of rows
+ */
+#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
+
+/*
+ * Memory Periodic Timer Prescaler
+ * Periodic timer for refresh, start with refresh rate for 40 MHz clock
+ * (CFG_8xx_CPUCLK_MIN / CFG_PTA_PER_CLK)
+ */
+#define CFG_MAMR_PTA 39
+
+/*
+ * For 16 MBit, refresh rates could be 31.3 us
+ * (= 64 ms / 2K = 125 / quad bursts).
+ * For a simpler initialization, 15.6 us is used instead.
+ *
+ * #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
+ * #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
+ */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+/* 10 column SDRAM */
+#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Network configuration
+ */
+#define CONFIG_SCC2_ENET /* enable ethernet on SCC2 */
+#define CONFIG_FEC_ENET /* enable ethernet on FEC */
+#define CONFIG_ETHER_ON_FEC1 /* ... for FEC1 */
+#define CONFIG_ETHER_ON_FEC2 /* ... for FEC2 */
+
+#if (CONFIG_COMMANDS & CFG_CMD_MII)
+#define CFG_DISCOVER_PHY
+#endif
+
+#define CONFIG_NET_RETRY_COUNT 1 /* reduce max. timeout before
+ switching to another netwok (if the
+ tried network is unreachable) */
+
+#define CONFIG_ETHPRIME "SCC ETHERNET"
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/aev.h b/include/configs/aev.h
index aa6bc91..8d9f0a1 100644
--- a/include/configs/aev.h
+++ b/include/configs/aev.h
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2003-2005
+ * (C) Copyright 2003-2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2004-2005
@@ -370,10 +370,7 @@
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
-/* automatic configuration of chip selects */
-#ifdef CONFIG_CS_AUTOCONF
#define CONFIG_LAST_STAGE_INIT
-#endif
/*
* SRAM - Do not map below 2 GB in address space, because this area is used
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index 6d32821..cd4339b 100644
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2005
+ * (C) Copyright 2005-2006
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* See file CREDITS for list of people who contributed to this
@@ -49,7 +49,7 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
@@ -257,8 +257,8 @@
"kernel_addr=fff00000\0" \
"ramdisk_addr=fff10000\0" \
"load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \
- "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \
- "cp.b 100000 fff80000 80000;" \
+ "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
+ "cp.b 100000 fffa0000 60000;" \
"setenv filesize;saveenv\0" \
"upd=run load;run update\0" \
""
@@ -310,11 +310,11 @@
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
- CFG_CMD_EEPROM | \
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -358,6 +358,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h
index 4a79835..a66cdc3 100644
--- a/include/configs/bubinga.h
+++ b/include/configs/bubinga.h
@@ -200,8 +200,9 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
diff --git a/include/configs/ebony.h b/include/configs/ebony.h
index a26af69..d8882ea 100644
--- a/include/configs/ebony.h
+++ b/include/configs/ebony.h
@@ -143,7 +143,13 @@
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
@@ -205,6 +211,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -243,8 +250,9 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
diff --git a/include/configs/gth2.h b/include/configs/gth2.h
index 77d2d56..a49ed3b 100644
--- a/include/configs/gth2.h
+++ b/include/configs/gth2.h
@@ -12,7 +12,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -34,7 +34,7 @@
#define CONFIG_AU1000 1
-#define CONFIG_MISC_INIT_R 1
+#define CONFIG_MISC_INIT_R 1
#define CONFIG_ETHADDR DE:AD:BE:EF:01:02 /* Ethernet address */
@@ -59,21 +59,21 @@
#define CONFIG_AUTOBOOT_DELAY_STR "d"
#define CONFIG_AUTOBOOT_STOP_STR " "
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-#define CONFIG_BOOTARGS "panic=1"
+#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+#define CONFIG_BOOTARGS "panic=1"
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CONFIG_EXTRA_ENV_SETTINGS \
"addmisc=setenv bootargs $(bootargs) " \
- "ethaddr=$(ethaddr) \0" \
- "netboot=bootp;run addmisc;bootm\0" \
- ""
+ "ethaddr=$(ethaddr) \0" \
+ "netboot=bootp;run addmisc;bootm\0" \
+ ""
/* Boot from Compact flash partition 2 as default */
#define CONFIG_BOOTCOMMAND "ide reset;disk 0x81000000 0:2;run addmisc;bootm"
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_IDE | CFG_CMD_DHCP ) & \
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_IDE | CFG_CMD_DHCP ) & \
~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | \
- CFG_CMD_MII | CFG_CMD_LOADS | CFG_CMD_LOADB | CFG_CMD_ELF | \
+ CFG_CMD_MII | CFG_CMD_LOADS | CFG_CMD_LOADB | CFG_CMD_ELF | \
CFG_CMD_BDI | CFG_CMD_BEDBUG | CFG_CMD_NFS | CFG_CMD_AUTOSCRIPT ))
#include <cmd_confdefs.h>
@@ -81,11 +81,11 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "GTH2 # " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args*/
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "GTH2 # " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args*/
#define CFG_MALLOC_LEN 128*1024
@@ -93,16 +93,16 @@
#define CFG_MHZ 500
-#define CFG_HZ (CFG_MHZ * 1000000) /* FIXME causes overflow in net.c */
+#define CFG_HZ (CFG_MHZ * 1000000) /* FIXME causes overflow in net.c */
#define CFG_SDRAM_BASE 0x80000000 /* Cached addr */
-#define CFG_LOAD_ADDR 0x81000000 /* default load address */
+#define CFG_LOAD_ADDR 0x81000000 /* default load address */
#define CFG_MEMTEST_START 0x80100000
#define CFG_MEMTEST_END 0x83000000
-#define CONFIG_HW_WATCHDOG 1
+#define CONFIG_HW_WATCHDOG 1
/*-----------------------------------------------------------------------
* FLASH and environment organization
@@ -113,8 +113,8 @@
#define PHYS_FLASH 0xbfc00000 /* Flash Bank #1 */
/* The following #defines are needed to get flash environment right */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (192 << 10)
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (192 << 10)
#define CFG_INIT_SP_OFFSET 0x400000
@@ -125,7 +125,7 @@
#define CFG_FLASH_ERASE_TOUT (2 * CFG_HZ) /* Timeout for Flash Erase */
#define CFG_FLASH_WRITE_TOUT (2 * CFG_HZ) /* Timeout for Flash Write */
-#define CFG_ENV_IS_NOWHERE 1
+#define CFG_ENV_IS_NOWHERE 1
/* Address and size of Primary Environment Sector */
#define CFG_ENV_ADDR 0xB0030000
@@ -158,21 +158,21 @@
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
#define CFG_ATA_IDE0_OFFSET 0
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_IO_BASE
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_IO_BASE
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET 0
+#define CFG_ATA_DATA_OFFSET 0
-/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET 0
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET 0
-/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x0200
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0200
/*-----------------------------------------------------------------------
* Cache Configuration
diff --git a/include/configs/kvme080.h b/include/configs/kvme080.h
new file mode 100644
index 0000000..61cf705
--- /dev/null
+++ b/include/configs/kvme080.h
@@ -0,0 +1,262 @@
+/*
+ * (C) Copyright 2005
+ * Sangmoon Kim, dogoil@etinsys.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MPC824X 1
+#define CONFIG_MPC8245 1
+#define CONFIG_KVME080 1
+
+#define CONFIG_CONS_INDEX 1
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_BOOTDELAY 5
+
+#define CONFIG_IPADDR 192.168.0.2
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_SERVERIP 192.168.0.1
+
+#define CONFIG_BOOTARGS \
+ "console=ttyS0,115200 " \
+ "root=/dev/nfs rw nfsroot=192.168.0.1:/opt/eldk/ppc_82xx " \
+ "ip=192.168.0.2:192.168.0.1:192.168.0.1:255.255.255.0:" \
+ "kvme080:eth0:none " \
+ "mtdparts=phys_mapped_flash:12m(root),-(kernel)"
+
+#define CONFIG_BOOTCOMMAND \
+ "tftp 800000 kvme080/uImage; " \
+ "bootm 800000"
+
+#define CONFIG_LOADADDR 800000
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_LOADS_ECHO 1
+#undef CFG_LOADS_BAUD_CHANGE
+
+#undef CONFIG_WATCHDOG
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_RTC_DS164x
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_ELF | \
+ CFG_CMD_I2C | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING | \
+ CFG_CMD_SDRAM | \
+ CFG_CMD_SNTP)
+
+#define CONFIG_NETCONSOLE
+
+#include <cmd_confdefs.h>
+
+#define CFG_LONGHELP
+#define CFG_PROMPT "=> "
+#define CFG_CBSIZE 256
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
+#define CFG_MAXARGS 16
+#define CFG_BARGSIZE CFG_CBSIZE
+
+#define CFG_MEMTEST_START 0x00400000
+#define CFG_MEMTEST_END 0x07C00000
+
+#define CFG_LOAD_ADDR 0x00100000
+#define CFG_HZ 1000
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_INIT_RAM_ADDR 0x40000000
+#define CFG_INIT_RAM_END 0x1000
+#define CFG_GBL_DATA_SIZE 128
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x7C000000
+#define CFG_EUMB_ADDR 0xFC000000
+#define CFG_NVRAM_BASE_ADDR 0xFF000000
+#define CFG_NS16550_COM1 0xFF080000
+#define CFG_NS16550_COM2 0xFF080010
+#define CFG_NS16550_COM3 0xFF080020
+#define CFG_NS16550_COM4 0xFF080030
+#define CFG_RESET_ADDRESS 0xFFF00100
+
+#define CFG_MAX_RAM_SIZE 0x20000000
+#define CFG_FLASH_SIZE (16 * 1024 * 1024)
+#define CFG_NVRAM_SIZE 0x7FFF8
+
+#define CONFIG_VERY_BIG_RAM
+
+#define CFG_MONITOR_LEN 0x00040000
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MALLOC_LEN (512 << 10)
+
+#define CFG_BOOTMAPSZ (8 << 20)
+
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_USE_BUFFER_WRITE
+#define CFG_FLASH_PROTECTION
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_PROTECT_CLEAR
+
+#define CFG_MAX_FLASH_BANKS 1
+#define CFG_MAX_FLASH_SECT 256
+
+#define CFG_FLASH_ERASE_TOUT 120000
+#define CFG_FLASH_WRITE_TOUT 500
+
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS 1
+
+#define CFG_ENV_IS_IN_NVRAM 1
+#define CONFIG_ENV_OVERWRITE 1
+#define CFG_NVRAM_ACCESS_ROUTINE
+#define CFG_ENV_ADDR CFG_NVRAM_BASE_ADDR
+#define CFG_ENV_SIZE 0x400
+#define CFG_ENV_OFFSET 0
+
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK 14745600
+
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+
+#define CONFIG_NET_MULTI
+#define CONFIG_EEPRO100
+#define CONFIG_EEPRO100_SROM_WRITE
+
+#define CFG_RX_ETH_BUFFER 8
+
+#define CONFIG_HARD_I2C 1
+#define CFG_I2C_SPEED 400000
+#define CFG_I2C_SLAVE 0x7F
+
+#define CFG_I2C_EEPROM_ADDR 0x57
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+#define CONFIG_SYS_CLK_FREQ 33333333
+
+#define CFG_CACHELINE_SIZE 32
+#if CONFIG_COMMANDS & CFG_CMD_KGDB
+# define CFG_CACHELINE_SHIFT 5
+#endif
+
+#define CFG_DLL_EXTEND 0x00
+#define CFG_PCI_HOLD_DEL 0x20
+
+#define CFG_ROMNAL 15
+#define CFG_ROMFAL 31
+
+#define CFG_REFINT 430
+
+#define CFG_DBUS_SIZE2 1
+
+#define CFG_BSTOPRE 121
+#define CFG_REFREC 8
+#define CFG_RDLAT 4
+#define CFG_PRETOACT 3
+#define CFG_ACTTOPRE 5
+#define CFG_ACTORW 3
+#define CFG_SDMODE_CAS_LAT 3
+#define CFG_SDMODE_WRAP 0
+
+#define CFG_REGISTERD_TYPE_BUFFER 1
+#define CFG_EXTROM 1
+#define CFG_REGDIMM 0
+
+#define CFG_BANK0_START 0x00000000
+#define CFG_BANK0_END (0x4000000 - 1)
+#define CFG_BANK0_ENABLE 1
+#define CFG_BANK1_START 0x04000000
+#define CFG_BANK1_END (0x8000000 - 1)
+#define CFG_BANK1_ENABLE 1
+#define CFG_BANK2_START 0x3ff00000
+#define CFG_BANK2_END 0x3fffffff
+#define CFG_BANK2_ENABLE 0
+#define CFG_BANK3_START 0x3ff00000
+#define CFG_BANK3_END 0x3fffffff
+#define CFG_BANK3_ENABLE 0
+#define CFG_BANK4_START 0x00000000
+#define CFG_BANK4_END 0x00000000
+#define CFG_BANK4_ENABLE 0
+#define CFG_BANK5_START 0x00000000
+#define CFG_BANK5_END 0x00000000
+#define CFG_BANK5_ENABLE 0
+#define CFG_BANK6_START 0x00000000
+#define CFG_BANK6_END 0x00000000
+#define CFG_BANK6_ENABLE 0
+#define CFG_BANK7_START 0x00000000
+#define CFG_BANK7_END 0x00000000
+#define CFG_BANK7_ENABLE 0
+
+#define CFG_BANK_ENABLE 0x03
+
+#define CFG_ODCR 0x75
+#define CFG_PGMAX 0x32
+
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+
+#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+
+#define BOOTFLAG_COLD 0x01
+#define BOOTFLAG_WARM 0x02
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/luan.h b/include/configs/luan.h
index 0335a00..0350e91 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -145,6 +145,13 @@
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
@@ -215,6 +222,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -253,6 +261,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/mcc200.h b/include/configs/mcc200.h
index d8d63a1..563f797 100644
--- a/include/configs/mcc200.h
+++ b/include/configs/mcc200.h
@@ -47,8 +47,27 @@
/*
* Serial console configuration
+ *
+ * To select console on the one of 8 external UARTs,
+ * define CONFIG_QUART_CONSOLE as 1, 2, 3, or 4 for the first Quad UART,
+ * or as 5, 6, 7, or 8 for the second Quad UART.
+ * COM11, COM12, COM13, COM14 are located on the second Quad UART.
+ *
+ * CONFIG_PSC_CONSOLE must be undefined in this case.
*/
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#ifdef CONFIG_CONSOLE_COM12
+#define CONFIG_QUART_CONSOLE 6 /* console is on UARTF of QUART2 */
+#else
+#define CONFIG_QUART_CONSOLE 8 /* console is on UARTH of QUART2 */
+#endif
+/*
+ * To select console on PSC1, define CONFIG_PSC_CONSOLE as 1
+ * and undefine CONFIG_QUART_CONSOLE.
+ */
+/*#define CONFIG_PSC_CONSOLE 1 */ /* console is on PSC1 */
+#if defined(CONFIG_QUART_CONSOLE) && defined(CONFIG_PSC_CONSOLE)
+#error "Select only one console device!"
+#endif
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
@@ -256,11 +275,59 @@
#define CFG_CS2_SIZE 0x00001000
#define CFG_CS2_CFG 0x1d300
+/* Second Quad UART @0x80010000 */
+#define CFG_CS1_START 0x80010000
+#define CFG_CS1_SIZE 0x00001000
+#define CFG_CS1_CFG 0x1d300
+
+/*
+ * Select one of quarts as a default
+ * console. If undefined - PSC console
+ * wil be default
+ */
#define CFG_CS_BURST 0x00000000
#define CFG_CS_DEADCYCLE 0x33333333
#define CFG_RESET_ADDRESS 0xff000000
+/*
+ * QUART Expanders support
+ */
+#if defined(CONFIG_QUART_CONSOLE)
+/*
+ * We'll use NS16550 chip routines,
+ */
+#define CFG_NS16550 1
+#define CFG_NS16550_SERIAL 1
+#define CONFIG_CONS_INDEX 1
+/*
+ * To achieve necessary offset on SC16C554
+ * A0-A2 (register select) pins with NS16550
+ * functions (in struct NS16550), REG_SIZE
+ * should be 4, because A0-A2 pins are connected
+ * to DA2-DA4 address bus lines.
+ */
+#define CFG_NS16550_REG_SIZE 4
+/*
+ * LocalPlus Bus already inited in cpu_init_f(),
+ * so can work with QUART's chip selects.
+ * One of four SC16C554 UARTs is selected with
+ * A3-A4 (DA5-DA6) lines.
+ */
+#if (CONFIG_QUART_CONSOLE > 0) && (CONFIG_QUART_CONSOLE < 5)
+#define CFG_NS16550_COM1 (CFG_CS2_START | (CONFIG_QUART_CONSOLE - 1)<<5)
+#elif (CONFIG_QUART_CONSOLE > 4) && (CONFIG_QUART_CONSOLE < 9)
+#define CFG_NS16550_COM1 (CFG_CS1_START | (CONFIG_QUART_CONSOLE - 5)<<5)
+#elif
+#error "Wrong QUART expander number."
+#endif
+
+/*
+ * SC16C554 chip's external crystal oscillator frequency
+ * is 7.3728 MHz
+ */
+#define CFG_NS16550_CLK 7372800
+#endif /* CONFIG_QUART_CONSOLE */
/*-----------------------------------------------------------------------
* USB stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h
index a13d6a8..89e9164 100644
--- a/include/configs/ocotea.h
+++ b/include/configs/ocotea.h
@@ -158,7 +158,13 @@
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
@@ -219,6 +225,9 @@
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
@@ -226,6 +235,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -264,15 +274,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/ppmc7xx.h b/include/configs/ppmc7xx.h
index ea15524..072b9dd 100644
--- a/include/configs/ppmc7xx.h
+++ b/include/configs/ppmc7xx.h
@@ -1,9 +1,9 @@
/*
* ppmc7xx.h
* ---------
- *
+ *
* Wind River PPMC 7xx/74xx board configuration file.
- *
+ *
* By Richard Danter (richard.danter@windriver.com)
* Copyright (C) 2005 Wind River Systems
*/
@@ -16,15 +16,15 @@
/*===================================================================
- *
+ *
* User configurable settings - Modify to your preference
- *
+ *
*===================================================================
*/
/*
* Debug
- *
+ *
* DEBUG - Define this is you want extra debug info
* GTREGREAD - Required to build with debug
* do_bdinfo - Required to build with debug
@@ -37,7 +37,7 @@
/*
* CPU type
- *
+ *
* CONFIG_7xx - We have a 750 or 755 CPU
* CONFIG_74xx - We have a 7400 CPU
* CONFIG_ALTIVEC - We have altivec enabled CPU (only 7400)
@@ -52,11 +52,11 @@
/*
* Monitor configuration
- *
+ *
* CONFIG_COMMANDS - List of command sets to include in shell
- *
+ *
* The following command sets have been tested and known to work:
- *
+ *
* CFG_CMD_CACHE - Cache control commands
* CFG_CMD_MEMORY - Memory display, change and test commands
* CFG_CMD_FLASH - Erase and program flash
@@ -91,7 +91,7 @@
/*
* PCI config
- *
+ *
* CONFIG_PCI - Enable PCI bus
* CONFIG_PCI_PNP - Enable Plug & Play support
* CONFIG_PCI_SCAN_SHOW - Enable display of devices at startup
@@ -104,7 +104,7 @@
/*
* Network config
- *
+ *
* CONFIG_NET_MULTI - Support for multiple network interfaces
* CONFIG_EEPRO100 - Intel 8255x Ethernet Controller
* CONFIG_EEPRO100_SROM_WRITE - Enable writing to network card ROM
@@ -117,18 +117,18 @@
/*
* Enable extra init functions
- *
+ *
* CONFIG_MISC_INIT_F - Call pre-relocation init functions
* CONFIG_MISC_INIT_R - Call post relocation init functions
*/
#undef CONFIG_MISC_INIT_F
-#define CONFIG_MISC_INIT_R
+#define CONFIG_MISC_INIT_R
/*
* Boot config
- *
+ *
* CONFIG_BOOTCOMMAND - Command(s) to execute to auto-boot
* CONFIG_BOOTDELAY - How long to wait before auto-boot (in sec)
*/
@@ -142,9 +142,9 @@
/*===================================================================
- *
+ *
* Board configuration settings - You should not need to modify these
- *
+ *
*===================================================================
*/
@@ -154,9 +154,9 @@
/*
* Memory map
- *
+ *
* This board runs in a standard CHRP (Map-B) configuration.
- *
+ *
* Type Start End Size Width Chip Sel
* ----------- ----------- ----------- ------- ------- --------
* SDRAM 0x00000000 0x04000000 64MB 64b SDRAMCS0
@@ -164,9 +164,9 @@
* UART 0x7C000000 RCS2
* Mailbox 0xFF000000 RCS1
* Flash 0xFFC00000 0xFFFFFFFF 4MB 64b RCS0
- *
+ *
* Flash sectors are laid out as follows.
- *
+ *
* Sector Start End Size Comments
* ------- ----------- ----------- ------- -----------
* 0 0xFFC00000 0xFFC3FFFF 256KB
@@ -193,7 +193,7 @@
/*
* SDRAM config - see memory map details above.
- *
+ *
* CFG_SDRAM_BASE - Start address of SDRAM, this _must_ be zero!
* CFG_SDRAM_SIZE - Total size of contiguous SDRAM bank(s)
*/
@@ -202,9 +202,9 @@
#define CFG_SDRAM_SIZE 0x04000000
-/*
+/*
* Flash config - see memory map details above.
- *
+ *
* CFG_FLASH_BASE - Start address of flash memory
* CFG_FLASH_SIZE - Total size of contiguous flash mem
* CFG_FLASH_ERASE_TOUT - Erase timeout in ms
@@ -223,7 +223,7 @@
/*
* Monitor config - see memory map details above
- *
+ *
* CFG_MONITOR_BASE - Base address of monitor code
* CFG_MALLOC_LEN - Size of malloc pool (128KB)
*/
@@ -234,7 +234,7 @@
/*
* Command shell settings
- *
+ *
* CFG_BARGSIZE - Boot Argument buffer size
* CFG_BOOTMAPSZ - Size of app's mapped RAM at boot (Linux=8MB)
* CFG_CBSIZE - Console Buffer (input) size
@@ -261,10 +261,10 @@
/*
* Environment config - see memory map details above
- *
+ *
* CFG_ENV_IS_IN_FLASH - The env variables are stored in flash
* CFG_ENV_ADDR - Address of the sector containing env vars
- * CFG_ENV_SIZE - Ammount of RAM for env vars (used to save RAM, 4KB)
+ * CFG_ENV_SIZE - Ammount of RAM for env vars (used to save RAM, 4KB)
* CFG_ENV_SECT_SIZE - Size of sector containing env vars (32KB)
*/
@@ -282,7 +282,7 @@
* Since the main system RAM is initialised very early, we place the INIT_RAM
* in the main system RAM just above the exception vectors. The contents are
* copied to top of RAM by the init code.
- *
+ *
* CFG_INIT_RAM_ADDR - Address of Init RAM, above exception vect
* CFG_INIT_RAM_END - Size of Init RAM
* CFG_GBL_DATA_SIZE - Ammount of RAM to reserve for global data
@@ -297,7 +297,7 @@
/*
* Initial BAT config
- *
+ *
* BAT0 - System SDRAM
* BAT1 - LED's and Serial Port
* BAT2 - PCI Memory
@@ -327,7 +327,7 @@
/*
* Cache config
- *
+ *
* CFG_CACHELINE_SIZE - Size of a cache line (CPU specific)
* CFG_L2 - L2 cache enabled if defined
* L2_INIT - L2 cache init flags
@@ -342,7 +342,7 @@
/*
* Clocks config
- *
+ *
* CFG_BUS_HZ - Bus clock frequency in Hz
* CFG_BUS_CLK - As above (?)
* CFG_HZ - Decrementer freq in Hz
@@ -355,7 +355,7 @@
/*
* Serial port config
- *
+ *
* CFG_BAUDRATE_TABLE - List of valid baud rates
* CFG_NS16550 - Include the NS16550 driver
* CFG_NS16550_SERIAL - Include the serial (wrapper) driver
@@ -398,7 +398,7 @@
/*
* Extra init functions
- *
+ *
* CFG_BOARD_ASM_INIT - Call assembly init code
*/
@@ -407,11 +407,11 @@
/*
* Boot flags
- *
+ *
* BOOTFLAG_COLD - Indicates a power-on boot
* BOOTFLAG_WARM - Indicates a software reset
*/
-
+
#define BOOTFLAG_COLD 0x01
#define BOOTFLAG_WARM 0x02
diff --git a/include/configs/sbc2410x.h b/include/configs/sbc2410x.h
new file mode 100644
index 0000000..866f7b0
--- /dev/null
+++ b/include/configs/sbc2410x.h
@@ -0,0 +1,239 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ * Gary Jennejohn <gj@denx.de>
+ * David Mueller <d.mueller@elsoft.ch>
+ *
+ * Modified for the friendly-arm SBC-2410X by
+ * (C) Copyright 2005
+ * JinHua Luo, GuangDong Linux Center, <luo.jinhua@gd-linux.com>
+ *
+ * Configuation settings for the friendly-arm SBC-2410X board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * If we are developing, we might want to start armboot from ram
+ * so we MUST NOT initialize critical regs like mem-timing ...
+ */
+#undef CONFIG_SKIP_LOWLEVEL_INIT /* undef for developing */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_ARM920T 1 /* This is an ARM920T Core */
+#define CONFIG_S3C2410 1 /* in a SAMSUNG S3C2410 SoC */
+#define CONFIG_SBC2410X 1 /* on a friendly-arm SBC-2410X Board */
+
+/* input clock of PLL */
+#define CONFIG_SYS_CLK_FREQ 12000000/* the SBC2410X has 12MHz input clock */
+
+
+#define USE_920T_MMU 1
+#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+
+/*
+ * Size of malloc() pool
+ */
+#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */
+#define CS8900_BASE 0x19000300
+#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on SBC2410X */
+
+/************************************************************
+ * RTC
+ ************************************************************/
+#define CONFIG_RTC_S3C24X0 1
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE 115200
+
+/***********************************************************
+ * Command definition
+ ***********************************************************/
+#define CONFIG_COMMANDS \
+ (CONFIG_CMD_DFL | \
+ CFG_CMD_CACHE | \
+ /*CFG_CMD_NAND |*/ \
+ /*CFG_CMD_EEPROM |*/ \
+ /*CFG_CMD_I2C |*/ \
+ /*CFG_CMD_USB |*/ \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_DATE | \
+ CFG_CMD_PING | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_ELF)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTARGS "console=ttySAC0 root=/dev/nfs nfsroot=192.168.0.1:/friendly-arm/rootfs_netserv ip=192.168.0.69:192.168.0.1:192.168.0.1:255.255.255.0:debian:eth0:off"
+#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_IPADDR 192.168.0.69
+#define CONFIG_SERVERIP 192.168.0.1
+/*#define CONFIG_BOOTFILE "elinos-lart" */
+#define CONFIG_BOOTCOMMAND "dhcp; bootm"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
+/* what's this ? it's not used anywhere */
+#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "[ ~ljh@GDLC ]# " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x30000000 /* memtest works on */
+#define CFG_MEMTEST_END 0x33F00000 /* 63 MB in DRAM */
+
+#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR 0x33000000 /* default load address */
+
+/* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
+/* it to wrap 100 times (total 1562500) to get 1 sec. */
+#define CFG_HZ 1562500
+
+/* valid baudrates */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
+#define PHYS_SDRAM_1 0x30000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
+
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+
+#define CFG_FLASH_BASE PHYS_FLASH_1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+/* #define CONFIG_AMD_LV400 1 /\* uncomment this if you have a LV400 flash *\/ */
+
+#define CONFIG_AMD_LV800 1 /* uncomment this if you have a LV800 flash */
+
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+
+#ifdef CONFIG_AMD_LV800
+#define PHYS_FLASH_SIZE 0x00100000 /* 1MB */
+#define CFG_MAX_FLASH_SECT (19) /* max number of sectors on one chip */
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x0F0000) /* addr of environment */
+#endif
+
+#ifdef CONFIG_AMD_LV400
+#define PHYS_FLASH_SIZE 0x00080000 /* 512KB */
+#define CFG_MAX_FLASH_SECT (11) /* max number of sectors on one chip */
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x070000) /* addr of environment */
+#endif
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT (5*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (5*CFG_HZ) /* Timeout for Flash Write */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
+
+/*-----------------------------------------------------------------------
+ * NAND flash settings
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define SECTORSIZE 512
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define NAND_WAIT_READY(nand) NF_WaitRB()
+#define NAND_DISABLE_CE(nand) NF_SetCE(NFCE_HIGH)
+#define NAND_ENABLE_CE(nand) NF_SetCE(NFCE_LOW)
+#define WRITE_NAND_COMMAND(d, adr) NF_Cmd(d)
+#define WRITE_NAND_COMMANDW(d, adr) NF_CmdW(d)
+#define WRITE_NAND_ADDRESS(d, adr) NF_Addr(d)
+#define WRITE_NAND(d, adr) NF_Write(d)
+#define READ_NAND(adr) NF_Read()
+/* the following functions are NOP's because S3C24X0 handles this in hardware */
+#define NAND_CTL_CLRALE(nandptr)
+#define NAND_CTL_SETALE(nandptr)
+#define NAND_CTL_CLRCLE(nandptr)
+#define NAND_CTL_SETCLE(nandptr)
+/* #undef CONFIG_MTD_NAND_VERIFY_WRITE */
+#endif /* CONFIG_COMMANDS & CFG_CMD_NAND */
+
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_TAG
+
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+#define CONFIG_CMDLINE_EDITING
+
+#ifdef CONFIG_CMDLINE_EDITING
+#undef CONFIG_AUTO_COMPLETE
+#else
+#define CONFIG_AUTO_COMPLETE
+#endif
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/spc1920.h b/include/configs/spc1920.h
new file mode 100644
index 0000000..9d3609a
--- /dev/null
+++ b/include/configs/spc1920.h
@@ -0,0 +1,362 @@
+/*
+ * (C) Copyright 2006
+ * Markus Klotzbuecher, DENX Software Engineering, mk@denx.de
+ *
+ * Configuation settings for the SPC1920 board.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __H
+#define __CONFIG_H
+
+#define CONFIG_SPC1920 1 /* SPC1920 board */
+#define CONFIG_MPC885 1 /* MPC885 CPU */
+
+#define CONFIG_8xx_CONS_SMC1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+
+#define CONFIG_MII
+/* #define MII_DEBUG */
+/* #define CONFIG_FEC_ENET */
+#undef CONFIG_ETHER_ON_FEC1
+#define CONFIG_ETHER_ON_FEC2
+#define FEC_ENET
+/* #define CONFIG_FEC2_PHY_NORXERR */
+/* #define CFG_DISCOVER_PHY */
+/* #define CONFIG_PHY_ADDR 0x1 */
+#define CONFIG_FEC2_PHY 1
+
+#define CONFIG_BAUDRATE 19200
+
+/* use PLD CLK4 instead of brg */
+#undef CFG_SPC1920_SMC1_CLK4
+
+#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz oscillator on EXTCLK */
+#define CONFIG_8xx_CPUCLK_DEFAULT 50000000
+#define CFG_8xx_CPUCLK_MIN 40000000
+#define CFG_8xx_CPUCLK_MAX 133000000
+
+#define CFG_RESET_ADDRESS 0xf8000000
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+
+#if 1
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "dhcp;" \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;" \
+ "bootm"
+
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs root=/dev/mtdblock2 rw mtdparts=phys:1280K(ROM)ro,-(root) "\
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;" \
+ "bootm fe080000"
+
+#undef CONFIG_BOOTARGS
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
+
+#ifndef CONFIG_COMMANDS
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_ASKENV \
+ | CFG_CMD_ECHO \
+ | CFG_CMD_IMMAP \
+ | CFG_CMD_JFFS2 \
+ | CFG_CMD_PING \
+ | CFG_CMD_DHCP \
+ | CFG_CMD_IMMAP \
+ | CFG_CMD_MII)
+ /* & ~( CFG_CMD_NET)) */
+
+
+#endif /* !CONFIG_COMMANDS */
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=>" /* Monitor Command Prompt */
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_LOAD_ADDR 0x00100000
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 2400, 4800, 9600, 19200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 KB for monitor */
+
+#ifdef CONFIG_BZIP2
+#define CFG_MALLOC_LEN (2500 << 10) /* Reserve ~2.5 MB for malloc() */
+#else
+#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
+#endif /* CONFIG_BZIP2 */
+
+#define CFG_ALLOC_DPRAM 1 /* use allocation routines */
+
+/*
+ * Flash
+ */
+/*-----------------------------------------------------------------------
+ * Flash organisation
+ */
+#define CFG_FLASH_BASE 0xFE000000
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */
+#define CFG_MAX_FLASH_SECT 128 /* Max num of sects on one chip */
+
+/* Environment is in flash */
+#define CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE 0x40000 /* We use one complete sector */
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+
+#define CONFIG_ENV_OVERWRITE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+
+/*-----------------------------------------------------------------------
+ * I2C configuration
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_I2C)
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address defaults */
+#define CFG_I2C_SLAVE 0x7F
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+/* #define CFG_SCCR SCCR_TBS */
+#define CFG_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * DER - Debug Enable Register
+ *-----------------------------------------------------------------------
+ * Set to zero to prevent the processor from entering debug mode
+ */
+#define CFG_DER 0
+
+
+/* Because of the way the 860 starts up and assigns CS0 the entire
+ * address space, we have to set the memory controller differently.
+ * Normally, you write the option register first, and then enable the
+ * chip select by writing the base register. For CS0, you must write
+ * the base register first, followed by the option register.
+ */
+
+
+/*
+ * Init Memory Controller:
+ */
+
+/* BR0 and OR0 (FLASH) */
+#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
+
+/*
+ * FLASH timing:
+ */
+#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
+ OR_SCY_3_CLK | OR_EHTR | OR_BI)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+
+
+/*
+ * SDRAM CS1 UPMB
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE_PRELIM CFG_SDRAM_BASE
+#define SDRAM_MAX_SIZE 0x4000000 /* max 64 MB */
+
+#define CFG_PRELIM_OR1_AM 0xF0000000
+/* #define CFG_OR1_TIMING OR_CSNT_SAM/\* | OR_G5LS /\\* *\\/ *\/ */
+#define SDRAM_TIMING OR_SCY_0_CLK /* SDRAM-Timing */
+
+#define CFG_OR1_PRELIM (CFG_PRELIM_OR1_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING)
+#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V)
+
+/* #define CFG_OR1_FINAL ((CFG_OR1_AM & OR_AM_MSK) | CFG_OR1_TIMING) */
+/* #define CFG_BR1_FINAL ((CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V) */
+
+#define CFG_PTB_PER_CLK ((4096 * 16 * 1000) / (4 * 64))
+#define CFG_PTA_PER_CLK 195
+#define CFG_MBMR_PTB 195
+#define CFG_MPTPR MPTPR_PTP_DIV16
+#define CFG_MAR 0x88
+
+#define CFG_MBMR_8COL ((CFG_MBMR_PTB << MBMR_PTB_SHIFT) | \
+ MBMR_AMB_TYPE_0 | \
+ MBMR_G0CLB_A10 | \
+ MBMR_DSB_1_CYCL | \
+ MBMR_RLFB_1X | \
+ MBMR_WLFB_1X | \
+ MBMR_TLFB_4X) /* 0x04804114 */ /* 0x10802114 */
+
+#define CFG_MBMR_9COL ((CFG_MBMR_PTB << MBMR_PTB_SHIFT) | \
+ MBMR_AMB_TYPE_1 | \
+ MBMR_G0CLB_A10 | \
+ MBMR_DSB_1_CYCL | \
+ MBMR_RLFB_1X | \
+ MBMR_WLFB_1X | \
+ MBMR_TLFB_4X) /* 0x04804114 */ /* 0x10802114 */
+
+
+/* PLD CS5 */
+#define CFG_SPC1920_PLD_BASE 0x80000000
+#define CFG_PRELIM_OR5_AM 0xffff8000
+
+#define CFG_OR5_PRELIM (CFG_PRELIM_OR5_AM | \
+ OR_CSNT_SAM | \
+ OR_ACS_DIV1 | \
+ OR_BI | \
+ OR_SCY_0_CLK | \
+ OR_TRLX)
+
+#define CFG_BR5_PRELIM ((CFG_SPC1920_PLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V);
+
+/* #define CFG_PLD_BASE 0x30000000 */
+/* #define CFG_OR5_PRELIM 0xffff1110 */
+/* #define CFG_BR5_PRELIM 0x30000401 */
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/* Machine type
+*/
+#define _MACH_8xx (_MACH_fads)
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/spieval.h b/include/configs/spieval.h
index 9ebb51e..f40dde2 100644
--- a/include/configs/spieval.h
+++ b/include/configs/spieval.h
@@ -452,32 +452,25 @@
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
-/* automatic configuration of chip selects */
-#ifdef CONFIG_CS_AUTOCONF
#define CONFIG_LAST_STAGE_INIT
-#endif
/*
* SRAM - Do not map below 2 GB in address space, because this area is used
* for SDRAM autosizing.
*/
-#if defined (CONFIG_CS_AUTOCONF)
#define CFG_CS2_START 0xE5000000
#define CFG_CS2_SIZE 0x100000 /* 1 MByte */
#define CFG_CS2_CFG 0x0004D930
-#endif
/*
* Grafic controller - Do not map below 2 GB in address space, because this
* area is used for SDRAM autosizing.
*/
-#if defined (CONFIG_CS_AUTOCONF)
#define SM501_FB_BASE 0xE0000000
#define CFG_CS1_START (SM501_FB_BASE)
#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
#define CFG_CS1_CFG 0x8F48FF70
#define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000
-#endif
#define CFG_CS_BURST 0x00000000
#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
diff --git a/include/configs/trab.h b/include/configs/trab.h
index 8f71acf..a2dc8e7 100644
--- a/include/configs/trab.h
+++ b/include/configs/trab.h
@@ -402,7 +402,7 @@
#endif
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_ERASE_TOUT (15*CFG_HZ) /* Timeout for Flash Erase */
#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
#define CFG_ENV_IS_IN_FLASH 1
diff --git a/include/configs/walnut.h b/include/configs/walnut.h
index 1171ee5..28abd6e 100644
--- a/include/configs/walnut.h
+++ b/include/configs/walnut.h
@@ -90,6 +90,11 @@
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* needed for NetConsole */
+
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
@@ -97,6 +102,7 @@
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
+ CFG_CMD_EEPROM | \
CFG_CMD_ELF | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
@@ -156,16 +162,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
@@ -175,6 +177,13 @@
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/xm250.h b/include/configs/xm250.h
index 952f73b..825bfd1 100644
--- a/include/configs/xm250.h
+++ b/include/configs/xm250.h
@@ -119,9 +119,9 @@
/*
* Definitions related to passing arguments to kernel.
*/
-#define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */
-#undef CONFIG_INITRD_TAG /* do not send initrd params */
+#define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */
+#define CONFIG_INITRD_TAG 1 /* do not send initrd params */
#undef CONFIG_VFD /* do not send framebuffer setup */
/*
diff --git a/include/configs/yellowstone.h b/include/configs/yellowstone.h
index 7d55566..cf42b66 100644
--- a/include/configs/yellowstone.h
+++ b/include/configs/yellowstone.h
@@ -229,6 +229,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -265,6 +266,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index a81cf34..86a85b8 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -231,6 +231,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -272,6 +273,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
new file mode 100644
index 0000000..a6532b5
--- /dev/null
+++ b/include/configs/yucca.h
@@ -0,0 +1,536 @@
+/*
+ * (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * 1 january 2005 Alain Saurel <asaurel@amcc.com>
+ * Adapted to current Das U-Boot source
+ ***********************************************************************/
+/************************************************************************
+ * yucca.h - configuration for AMCC 440SPe Ref (yucca)
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_4xx 1 /* ... PPC4xx family */
+#define CONFIG_440 1 /* ... PPC440 family */
+#define CONFIG_440SPE 1 /* Specifc SPe support */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+#undef CFG_DRAM_TEST /* Disable-takes long time */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+#define EXTCLK_33_33 33333333
+#define EXTCLK_66_66 66666666
+#define EXTCLK_50 50000000
+#define EXTCLK_83 83333333
+
+#define CONFIG_IBM_EMAC4_V4 1
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+#undef CONFIG_SHOW_BOOT_PROGRESS
+#undef CONFIG_STRESS
+#undef ENABLE_ECC
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */
+#define CFG_MONITOR_BASE 0xfffb0000 /* start of monitor */
+#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
+#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
+
+#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
+#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
+#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
+
+#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
+#define CFG_PCIE_MEMSIZE 0x01000000
+#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */
+
+#define CFG_PCIE0_CFGBASE 0xc0000000
+#define CFG_PCIE0_XCFGBASE 0xc0000400
+#define CFG_PCIE1_CFGBASE 0xc0001000
+#define CFG_PCIE1_XCFGBASE 0xc0001400
+#define CFG_PCIE2_CFGBASE 0xc0002000
+#define CFG_PCIE2_XCFGBASE 0xc0002400
+
+/* System RAM mapped to PCI space */
+#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024)
+
+#define CFG_FPGA_BASE 0xe2000000 /* epld */
+#define CFG_OPER_FLASH 0xe7000000 /* SRAM - OPER Flash */
+
+/* #define CFG_NVRAM_BASE_ADDR 0x08000000 */
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in internal SRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_TEMP_STACK_OCM 1
+#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE
+#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
+#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
+
+#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Mon */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_SERIAL_MULTI 1
+#undef CONFIG_UART1_CONSOLE
+
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#undef CFG_EXT_SERIAL_CLOCK
+/* #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) */ /* Ext clk @ 11.059 MHz */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
+#define SPD_EEPROM_ADDRESS {0x53, 0x52} /* SPD i2c spd addresses */
+#define IIC0_DIMM0_ADDR 0x53
+#define IIC0_DIMM1_ADDR 0x52
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define IIC0_BOOTPROM_ADDR 0x50
+#define IIC0_ALT_BOOTPROM_ADDR 0x54
+
+/* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x50, 0x52, 0x53, 0x54}
+
+/* #if (CONFIG_COMMANDS & CFG_CMD_EEPROM) */
+/* #define CFG_I2C_EEPROM_ADDR 0x50 */ /* I2C boot EEPROM */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
+/* #endif */
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+/* #define CFG_NVRAM_SIZE (0x2000 - 8) */ /* NVRAM size(8k)- RTC regs */
+
+#undef CFG_ENV_IS_IN_NVRAM /* ... not in NVRAM */
+#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */
+#undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */
+#define CONFIG_ENV_OVERWRITE 1
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "hostname=yucca\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
+ "bootm\0" \
+ "rootpath=/opt/eldk/ppc_4xx\0" \
+ "bootfile=yucca/uImage\0" \
+ "kernel_addr=E7F10000\0" \
+ "ramdisk_addr=E7F20000\0" \
+ "load=tftp 100000 yuca/u-boot.bin\0" \
+ "update=protect off 2:4-7;era 2:4-7;" \
+ "cp.b ${fileaddr} FFFB0000 ${filesize};" \
+ "setenv filesize;saveenv\0" \
+ "upd=run load;run update\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_ELF | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_MII | \
+ CFG_CMD_NET | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_SDRAM )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_MII 1 /* MII PHY management */
+#undef CONFIG_NET_MULTI
+#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
+#define CONFIG_HAS_ETH0
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
+#define CONFIG_PHY_RESET_DELAY 1000
+#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* needed for NetConsole */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_FLASH_BANKS 3 /* number of banks */
+#define CFG_MAX_FLASH_SECT 256 /* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_ADDR0 0x5555
+#define CFG_FLASH_ADDR1 0x2aaa
+#define CFG_FLASH_WORD_SIZE unsigned char
+
+#define CFG_FLASH_2ND_16BIT_DEV 1 /* evb440SPe has 8 and 16bit device */
+#define CFG_FLASH_2ND_ADDR 0xe7c00000 /* evb440SPe has 8 and 16bit device*/
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CFG_ENV_ADDR 0xfffa0000
+/* #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) */
+#define CFG_ENV_SIZE 0x10000 /* Size of Environment vars */
+#endif /* CFG_ENV_IS_IN_FLASH */
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+/* General PCI */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
+#undef CONFIG_PCI_CONFIG_HOST_BRIDGE
+
+/* Board-specific PCI */
+#define CFG_PCI_PRE_INIT 1 /* enable board pci_pre_init() */
+#define CFG_PCI_TARGET_INIT /* let board init pci target */
+#undef CFG_PCI_MASTER_INIT
+
+#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
+#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
+/* #define CFG_PCI_SUBSYS_ID CFG_PCI_SUBSYS_DEVICEID */
+
+/*
+ * NETWORK Support (PCI):
+ */
+/* Support for Intel 82557/82559/82559ER chips. */
+#define CONFIG_EEPRO100
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/* FB Divisor selection */
+#define FPGA_FB_DIV_6 6
+#define FPGA_FB_DIV_10 10
+#define FPGA_FB_DIV_12 12
+#define FPGA_FB_DIV_20 20
+
+/* VCO Divisor selection */
+#define FPGA_VCO_DIV_4 4
+#define FPGA_VCO_DIV_6 6
+#define FPGA_VCO_DIV_8 8
+#define FPGA_VCO_DIV_10 10
+
+/*----------------------------------------------------------------------------+
+| FPGA registers and bit definitions
++----------------------------------------------------------------------------*/
+/* PowerPC 440SPe Board FPGA is reached with physical address 0x1 E2000000. */
+/* TLB initialization makes it correspond to logical address 0xE2000000. */
+/* => Done init_chip.s in bootlib */
+#define FPGA_REG_BASE_ADDR 0xE2000000
+#define FPGA_GPIO_BASE_ADDR 0xE2010000
+#define FPGA_INT_BASE_ADDR 0xE2020000
+
+/*----------------------------------------------------------------------------+
+| Display
++----------------------------------------------------------------------------*/
+#define PPC440SPE_DISPLAY FPGA_REG_BASE_ADDR
+
+#define PPC440SPE_DISPLAY_D8 (FPGA_REG_BASE_ADDR+0x06)
+#define PPC440SPE_DISPLAY_D4 (FPGA_REG_BASE_ADDR+0x04)
+#define PPC440SPE_DISPLAY_D2 (FPGA_REG_BASE_ADDR+0x02)
+#define PPC440SPE_DISPLAY_D1 (FPGA_REG_BASE_ADDR+0x00)
+/*define WRITE_DISPLAY_DIGIT(n) IOREG8(FPGA_REG_BASE_ADDR + (2*n))*/
+/*#define IOREG8(addr) *((volatile unsigned char *)(addr))*/
+
+/*----------------------------------------------------------------------------+
+| ethernet/reset/boot Register 1
++----------------------------------------------------------------------------*/
+#define FPGA_REG10 (FPGA_REG_BASE_ADDR+0x10)
+
+#define FPGA_REG10_10MHZ_ENABLE 0x8000
+#define FPGA_REG10_100MHZ_ENABLE 0x4000
+#define FPGA_REG10_GIGABIT_ENABLE 0x2000
+#define FPGA_REG10_FULL_DUPLEX 0x1000 /* force Full Duplex*/
+#define FPGA_REG10_RESET_ETH 0x0800
+#define FPGA_REG10_AUTO_NEG_DIS 0x0400
+#define FPGA_REG10_INTP_ETH 0x0200
+
+#define FPGA_REG10_RESET_HISR 0x0080
+#define FPGA_REG10_ENABLE_DISPLAY 0x0040
+#define FPGA_REG10_RESET_SDRAM 0x0020
+#define FPGA_REG10_OPER_BOOT 0x0010
+#define FPGA_REG10_SRAM_BOOT 0x0008
+#define FPGA_REG10_SMALL_BOOT 0x0004
+#define FPGA_REG10_FORCE_COLA 0x0002
+#define FPGA_REG10_COLA_MANUAL 0x0001
+
+#define FPGA_REG10_SDRAM_ENABLE 0x0020
+
+#define FPGA_REG10_ENET_ENCODE2(n) ((((unsigned long)(n))&0x0F)<<4) /*from ocotea ?*/
+#define FPGA_REG10_ENET_DECODE2(n) ((((unsigned long)(n))>>4)&0x0F) /*from ocotea ?*/
+
+/*----------------------------------------------------------------------------+
+| MUX control
++----------------------------------------------------------------------------*/
+#define FPGA_REG12 (FPGA_REG_BASE_ADDR+0x12)
+
+#define FPGA_REG12_EBC_CTL 0x8000
+#define FPGA_REG12_UART1_CTS_RTS 0x4000
+#define FPGA_REG12_UART0_RX_ENABLE 0x2000
+#define FPGA_REG12_UART1_RX_ENABLE 0x1000
+#define FPGA_REG12_UART2_RX_ENABLE 0x0800
+#define FPGA_REG12_EBC_OUT_ENABLE 0x0400
+#define FPGA_REG12_GPIO0_OUT_ENABLE 0x0200
+#define FPGA_REG12_GPIO1_OUT_ENABLE 0x0100
+#define FPGA_REG12_GPIO_SELECT 0x0010
+#define FPGA_REG12_GPIO_CHREG 0x0008
+#define FPGA_REG12_GPIO_CLK_CHREG 0x0004
+#define FPGA_REG12_GPIO_OETRI 0x0002
+#define FPGA_REG12_EBC_ERROR 0x0001
+
+/*----------------------------------------------------------------------------+
+| PCI Clock control
++----------------------------------------------------------------------------*/
+#define FPGA_REG16 (FPGA_REG_BASE_ADDR+0x16)
+
+#define FPGA_REG16_PCI_CLK_CTL0 0x8000
+#define FPGA_REG16_PCI_CLK_CTL1 0x4000
+#define FPGA_REG16_PCI_CLK_CTL2 0x2000
+#define FPGA_REG16_PCI_CLK_CTL3 0x1000
+#define FPGA_REG16_PCI_CLK_CTL4 0x0800
+#define FPGA_REG16_PCI_CLK_CTL5 0x0400
+#define FPGA_REG16_PCI_CLK_CTL6 0x0200
+#define FPGA_REG16_PCI_CLK_CTL7 0x0100
+#define FPGA_REG16_PCI_CLK_CTL8 0x0080
+#define FPGA_REG16_PCI_CLK_CTL9 0x0040
+#define FPGA_REG16_PCI_EXT_ARB0 0x0020
+#define FPGA_REG16_PCI_MODE_1 0x0010
+#define FPGA_REG16_PCI_TARGET_MODE 0x0008
+#define FPGA_REG16_PCI_INTP_MODE 0x0004
+
+/* FB1 Divisor selection */
+#define FPGA_REG16_FB2_DIV_MASK 0x1000
+#define FPGA_REG16_FB2_DIV_LOW 0x0000
+#define FPGA_REG16_FB2_DIV_HIGH 0x1000
+/* FB2 Divisor selection */
+/* S3 switch on Board */
+#define FPGA_REG16_FB1_DIV_MASK 0x2000
+#define FPGA_REG16_FB1_DIV_LOW 0x0000
+#define FPGA_REG16_FB1_DIV_HIGH 0x2000
+/* PCI0 Clock Selection */
+/* S3 switch on Board */
+#define FPGA_REG16_PCI0_CLK_MASK 0x0c00
+#define FPGA_REG16_PCI0_CLK_33_33 0x0000
+#define FPGA_REG16_PCI0_CLK_66_66 0x0800
+#define FPGA_REG16_PCI0_CLK_100 0x0400
+#define FPGA_REG16_PCI0_CLK_133_33 0x0c00
+/* VCO Divisor selection */
+/* S3 switch on Board */
+#define FPGA_REG16_VCO_DIV_MASK 0xc000
+#define FPGA_REG16_VCO_DIV_4 0x0000
+#define FPGA_REG16_VCO_DIV_8 0x4000
+#define FPGA_REG16_VCO_DIV_6 0x8000
+#define FPGA_REG16_VCO_DIV_10 0xc000
+/* Master Clock Selection */
+/* S3, S4 switches on Board */
+#define FPGA_REG16_MASTER_CLK_MASK 0x01c0
+#define FPGA_REG16_MASTER_CLK_EXT 0x0000
+#define FPGA_REG16_MASTER_CLK_66_66 0x0040
+#define FPGA_REG16_MASTER_CLK_50 0x0080
+#define FPGA_REG16_MASTER_CLK_33_33 0x00c0
+#define FPGA_REG16_MASTER_CLK_25 0x0100
+
+/*----------------------------------------------------------------------------+
+| PCI Miscellaneous
++----------------------------------------------------------------------------*/
+#define FPGA_REG18 (FPGA_REG_BASE_ADDR+0x18)
+
+#define FPGA_REG18_PCI_PRSNT1 0x8000
+#define FPGA_REG18_PCI_PRSNT2 0x4000
+#define FPGA_REG18_PCI_INTA 0x2000
+#define FPGA_REG18_PCI_SLOT0_INTP 0x1000
+#define FPGA_REG18_PCI_SLOT1_INTP 0x0800
+#define FPGA_REG18_PCI_SLOT2_INTP 0x0400
+#define FPGA_REG18_PCI_SLOT3_INTP 0x0200
+#define FPGA_REG18_PCI_PCI0_VC 0x0100
+#define FPGA_REG18_PCI_PCI0_VTH1 0x0080
+#define FPGA_REG18_PCI_PCI0_VTH2 0x0040
+#define FPGA_REG18_PCI_PCI0_VTH3 0x0020
+
+/*----------------------------------------------------------------------------+
+| PCIe Miscellaneous
++----------------------------------------------------------------------------*/
+#define FPGA_REG1A (FPGA_REG_BASE_ADDR+0x1A)
+
+#define FPGA_REG1A_PE0_GLED 0x8000
+#define FPGA_REG1A_PE1_GLED 0x4000
+#define FPGA_REG1A_PE2_GLED 0x2000
+#define FPGA_REG1A_PE0_YLED 0x1000
+#define FPGA_REG1A_PE1_YLED 0x0800
+#define FPGA_REG1A_PE2_YLED 0x0400
+#define FPGA_REG1A_PE0_PWRON 0x0200
+#define FPGA_REG1A_PE1_PWRON 0x0100
+#define FPGA_REG1A_PE2_PWRON 0x0080
+#define FPGA_REG1A_PE0_REFCLK_ENABLE 0x0040
+#define FPGA_REG1A_PE1_REFCLK_ENABLE 0x0020
+#define FPGA_REG1A_PE2_REFCLK_ENABLE 0x0010
+#define FPGA_REG1A_PE_SPREAD0 0x0008
+#define FPGA_REG1A_PE_SPREAD1 0x0004
+#define FPGA_REG1A_PE_SELSOURCE_0 0x0002
+#define FPGA_REG1A_PE_SELSOURCE_1 0x0001
+
+/*----------------------------------------------------------------------------+
+| PCIe Miscellaneous
++----------------------------------------------------------------------------*/
+#define FPGA_REG1C (FPGA_REG_BASE_ADDR+0x1C)
+
+#define FPGA_REG1C_PE0_ROOTPOINT 0x8000
+#define FPGA_REG1C_PE1_ENDPOINT 0x4000
+#define FPGA_REG1C_PE2_ENDPOINT 0x2000
+#define FPGA_REG1C_PE0_PRSNT 0x1000
+#define FPGA_REG1C_PE1_PRSNT 0x0800
+#define FPGA_REG1C_PE2_PRSNT 0x0400
+#define FPGA_REG1C_PE0_WAKE 0x0080
+#define FPGA_REG1C_PE1_WAKE 0x0040
+#define FPGA_REG1C_PE2_WAKE 0x0020
+#define FPGA_REG1C_PE0_PERST 0x0010
+#define FPGA_REG1C_PE1_PERST 0x0008
+#define FPGA_REG1C_PE2_PERST 0x0004
+
+/*----------------------------------------------------------------------------+
+| Defines
++----------------------------------------------------------------------------*/
+#define PERIOD_133_33MHZ 7500 /* 7,5ns */
+#define PERIOD_100_00MHZ 10000 /* 10ns */
+#define PERIOD_83_33MHZ 12000 /* 12ns */
+#define PERIOD_75_00MHZ 13333 /* 13,333ns */
+#define PERIOD_66_66MHZ 15000 /* 15ns */
+#define PERIOD_50_00MHZ 20000 /* 20ns */
+#define PERIOD_33_33MHZ 30000 /* 30ns */
+#define PERIOD_25_00MHZ 40000 /* 40ns */
+
+/*---------------------------------------------------------------------------*/
+
+#endif /* __CONFIG_H */
diff --git a/include/fat.h b/include/fat.h
index 0645458..92638d5 100644
--- a/include/fat.h
+++ b/include/fat.h
@@ -175,15 +175,19 @@
__u8 name11_12[4]; /* Last 2 characters in name */
} dir_slot;
-/* Private filesystem parameters */
+/* Private filesystem parameters
+ *
+ * Note: FAT buffer has to be 32 bit aligned
+ * (see FAT32 accesses)
+ */
typedef struct {
+ __u8 fatbuf[FATBUFSIZE]; /* Current FAT buffer */
int fatsize; /* Size of FAT in bits */
__u16 fatlength; /* Length of FAT in sectors */
__u16 fat_sect; /* Starting sector of the FAT */
__u16 rootdir_sect; /* Start sector of root directory */
__u16 clust_size; /* Size of clusters in sectors */
short data_begin; /* The sector of the first cluster, can be negative */
- __u8 fatbuf[FATBUFSIZE]; /* Current FAT buffer */
int fatbufnum; /* Used by get_fatent, init to -1 */
} fsdata;
diff --git a/include/galileo/core.h b/include/galileo/core.h
index 0735d07..49f4dd2 100644
--- a/include/galileo/core.h
+++ b/include/galileo/core.h
@@ -110,7 +110,10 @@
#define _1G 0x40000000
#define _2G 0x80000000
+#ifndef BOOL_WAS_DEFINED
+#define BOOL_WAS_DEFINED
typedef enum _bool{false,true} bool;
+#endif
/* Little to Big endian conversion macros */
diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index a522718..4b48564 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -2,7 +2,7 @@
* linux/include/linux/mtd/nand.h
*
* Copyright (c) 2000 David Woodhouse <dwmw2@mvhi.com>
- * Steven J. Hill <sjhill@realitydiluted.com>
+ * Steven J. Hill <sjhill@realitydiluted.com>
* Thomas Gleixner <tglx@linutronix.de>
*
* $Id: nand.h,v 1.68 2004/11/12 10:40:37 gleixner Exp $
@@ -15,15 +15,15 @@
* Contains standard defines and IDs for NAND flash devices
*
* Changelog:
- * 01-31-2000 DMW Created
- * 09-18-2000 SJH Moved structure out of the Disk-On-Chip drivers
+ * 01-31-2000 DMW Created
+ * 09-18-2000 SJH Moved structure out of the Disk-On-Chip drivers
* so it can be used by other NAND flash device
* drivers. I also changed the copyright since none
* of the original contents of this file are specific
* to DoC devices. David can whack me with a baseball
* bat later if I did something naughty.
- * 10-11-2000 SJH Added private NAND flash structure for driver
- * 10-24-2000 SJH Added prototype for 'nand_scan' function
+ * 10-11-2000 SJH Added private NAND flash structure for driver
+ * 10-24-2000 SJH Added prototype for 'nand_scan' function
* 10-29-2001 TG changed nand_chip structure to support
* hardwarespecific function for accessing control lines
* 02-21-2002 TG added support for different read/write adress and
@@ -36,7 +36,7 @@
* CONFIG_MTD_NAND_ECC_JFFS2 is not set
* 08-10-2002 TG extensions to nand_chip structure to support HW-ECC
*
- * 08-29-2002 tglx nand_chip structure: data_poi for selecting
+ * 08-29-2002 tglx nand_chip structure: data_poi for selecting
* internal / fs-driver buffer
* support for 6byte/512byte hardware ECC
* read_ecc, write_ecc extended for different oob-layout
@@ -45,8 +45,8 @@
* 11-25-2002 tglx Added Manufacturer code FUJITSU, NATIONAL
* Split manufacturer and device ID structures
*
- * 02-08-2004 tglx added option field to nand structure for chip anomalities
- * 05-25-2004 tglx added bad block table support, ST-MICRO manufacturer id
+ * 02-08-2004 tglx added option field to nand structure for chip anomalities
+ * 05-25-2004 tglx added bad block table support, ST-MICRO manufacturer id
* update of nand_chip structure description
*/
#ifndef __LINUX_MTD_NAND_H
@@ -75,7 +75,7 @@
* Constants for hardware specific CLE/ALE/NCE function
*/
/* Select the chip by setting nCE to low */
-#define NAND_CTL_SETNCE 1
+#define NAND_CTL_SETNCE 1
/* Deselect the chip by setting nCE to high */
#define NAND_CTL_CLRNCE 2
/* Select the command latch by setting CLE to high */
@@ -215,7 +215,7 @@
#if 0
/**
* struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independend devices
- * @lock: protection lock
+ * @lock: protection lock
* @active: the mtd device which holds the controller currently
*/
struct nand_hw_control {
@@ -244,20 +244,20 @@
* is read from the chip status register
* @cmdfunc: [REPLACEABLE] hardwarespecific function for writing commands to the chip
* @waitfunc: [REPLACEABLE] hardwarespecific function for wait on ready
- * @calculate_ecc: [REPLACEABLE] function for ecc calculation or readback from ecc hardware
+ * @calculate_ecc: [REPLACEABLE] function for ecc calculation or readback from ecc hardware
* @correct_data: [REPLACEABLE] function for ecc correction, matching to ecc generator (sw/hw)
* @enable_hwecc: [BOARDSPECIFIC] function to enable (reset) hardware ecc generator. Must only
* be provided if a hardware ECC is available
* @erase_cmd: [INTERN] erase command write function, selectable due to AND support
* @scan_bbt: [REPLACEABLE] function to scan bad block table
* @eccmode: [BOARDSPECIFIC] mode of ecc, see defines
- * @eccsize: [INTERN] databytes used per ecc-calculation
- * @eccbytes: [INTERN] number of ecc bytes per ecc-calculation step
+ * @eccsize: [INTERN] databytes used per ecc-calculation
+ * @eccbytes: [INTERN] number of ecc bytes per ecc-calculation step
* @eccsteps: [INTERN] number of ecc calculation steps per page
* @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR)
* @chip_lock: [INTERN] spinlock used to protect access to this structure and the chip
* @wq: [INTERN] wait queue to sleep on if a NAND operation is in progress
- * @state: [INTERN] the current state of the NAND device
+ * @state: [INTERN] the current state of the NAND device
* @page_shift: [INTERN] number of address bits in a page (column address bits)
* @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock
* @bbt_erase_shift: [INTERN] number of address bits in a bbt entry
@@ -284,7 +284,7 @@
struct nand_chip {
void __iomem *IO_ADDR_R;
- void __iomem *IO_ADDR_W;
+ void __iomem *IO_ADDR_W;
u_char (*read_byte)(struct mtd_info *mtd);
void (*write_byte)(struct mtd_info *mtd, u_char byte);
@@ -297,12 +297,12 @@
void (*select_chip)(struct mtd_info *mtd, int chip);
int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip);
int (*block_markbad)(struct mtd_info *mtd, loff_t ofs);
- void (*hwcontrol)(struct mtd_info *mtd, int cmd);
- int (*dev_ready)(struct mtd_info *mtd);
- void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr);
- int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this, int state);
+ void (*hwcontrol)(struct mtd_info *mtd, int cmd);
+ int (*dev_ready)(struct mtd_info *mtd);
+ void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr);
+ int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this, int state);
int (*calculate_ecc)(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code);
- int (*correct_data)(struct mtd_info *mtd, u_char *dat, u_char *read_ecc, u_char *calc_ecc);
+ int (*correct_data)(struct mtd_info *mtd, u_char *dat, u_char *read_ecc, u_char *calc_ecc);
void (*enable_hwecc)(struct mtd_info *mtd, int mode);
void (*erase_cmd)(struct mtd_info *mtd, int page);
int (*scan_bbt)(struct mtd_info *mtd);
@@ -310,17 +310,17 @@
int eccsize;
int eccbytes;
int eccsteps;
- int chip_delay;
+ int chip_delay;
#if 0
spinlock_t chip_lock;
wait_queue_head_t wq;
- nand_state_t state;
+ nand_state_t state;
#endif
- int page_shift;
+ int page_shift;
int phys_erase_shift;
int bbt_erase_shift;
int chip_shift;
- u_char *data_buf;
+ u_char *data_buf;
u_char *oob_buf;
int oobdirty;
u_char *data_poi;
@@ -335,7 +335,7 @@
struct nand_bbt_descr *bbt_td;
struct nand_bbt_descr *bbt_md;
struct nand_bbt_descr *badblock_pattern;
- struct nand_hw_control *controller;
+ struct nand_hw_control *controller;
void *priv;
};
@@ -352,14 +352,14 @@
/**
* struct nand_flash_dev - NAND Flash Device ID Structure
*
- * @name: Identify the device type
- * @id: device ID code
- * @pagesize: Pagesize in bytes. Either 256 or 512 or 0
+ * @name: Identify the device type
+ * @id: device ID code
+ * @pagesize: Pagesize in bytes. Either 256 or 512 or 0
* If the pagesize is 0, then the real pagesize
* and the eraseize are determined from the
* extended id bytes in the chip
- * @erasesize: Size of an erase block in the flash device.
- * @chipsize: Total chipsize in Mega Bytes
+ * @erasesize: Size of an erase block in the flash device.
+ * @chipsize: Total chipsize in Mega Bytes
* @options: Bitfield to store chip relevant options
*/
struct nand_flash_dev {
@@ -374,7 +374,7 @@
/**
* struct nand_manufacturers - NAND Flash Manufacturer ID Structure
* @name: Manufacturer name
- * @id: manufacturer ID code of device.
+ * @id: manufacturer ID code of device.
*/
struct nand_manufacturers {
int id;
@@ -398,7 +398,7 @@
* blocks is reserved at the end of the device where the tables are
* written.
* @reserved_block_code: if non-0, this pattern denotes a reserved (rather than
- * bad) block in the stored bbt
+ * bad) block in the stored bbt
* @pattern: pattern to identify bad block table or factory marked good /
* bad blocks, can be NULL, if len = 0
*
@@ -412,11 +412,11 @@
int pages[NAND_MAX_CHIPS];
int offs;
int veroffs;
- uint8_t version[NAND_MAX_CHIPS];
+ uint8_t version[NAND_MAX_CHIPS];
int len;
- int maxblocks;
+ int maxblocks;
int reserved_block_code;
- uint8_t *pattern;
+ uint8_t *pattern;
};
/* Options for the bad block table descriptors */
@@ -428,7 +428,7 @@
#define NAND_BBT_4BIT 0x00000004
#define NAND_BBT_8BIT 0x00000008
/* The bad block table is in the last good block of the device */
-#define NAND_BBT_LASTBLOCK 0x00000010
+#define NAND_BBT_LASTBLOCK 0x00000010
/* The bbt is at the given page, else we must scan for the bbt */
#define NAND_BBT_ABSPAGE 0x00000020
/* The bbt is at the given page, else we must scan for the bbt */
@@ -451,7 +451,7 @@
#define NAND_BBT_SCAN2NDPAGE 0x00004000
/* The maximum number of blocks to scan for a bbt */
-#define NAND_BBT_SCAN_MAXBLOCKS 4
+#define NAND_BBT_SCAN_MAXBLOCKS 4
extern int nand_scan_bbt (struct mtd_info *mtd, struct nand_bbt_descr *bd);
extern int nand_update_bbt (struct mtd_info *mtd, loff_t offs);
diff --git a/include/mpc5xxx.h b/include/mpc5xxx.h
index 50a6ac1..daa4d5f 100644
--- a/include/mpc5xxx.h
+++ b/include/mpc5xxx.h
@@ -235,20 +235,30 @@
/* General Purpose Timers registers */
#define MPC5XXX_GPT0_ENABLE (MPC5XXX_GPT + 0x0)
#define MPC5XXX_GPT0_COUNTER (MPC5XXX_GPT + 0x4)
+#define MPC5XXX_GPT0_STATUS (MPC5XXX_GPT + 0x0C)
#define MPC5XXX_GPT1_ENABLE (MPC5XXX_GPT + 0x10)
#define MPC5XXX_GPT1_COUNTER (MPC5XXX_GPT + 0x14)
+#define MPC5XXX_GPT1_STATUS (MPC5XXX_GPT + 0x1C)
#define MPC5XXX_GPT2_ENABLE (MPC5XXX_GPT + 0x20)
#define MPC5XXX_GPT2_COUNTER (MPC5XXX_GPT + 0x24)
+#define MPC5XXX_GPT2_STATUS (MPC5XXX_GPT + 0x2C)
#define MPC5XXX_GPT3_ENABLE (MPC5XXX_GPT + 0x30)
#define MPC5XXX_GPT3_COUNTER (MPC5XXX_GPT + 0x34)
+#define MPC5XXX_GPT3_STATUS (MPC5XXX_GPT + 0x3C)
#define MPC5XXX_GPT4_ENABLE (MPC5XXX_GPT + 0x40)
#define MPC5XXX_GPT4_COUNTER (MPC5XXX_GPT + 0x44)
+#define MPC5XXX_GPT4_STATUS (MPC5XXX_GPT + 0x4C)
#define MPC5XXX_GPT5_ENABLE (MPC5XXX_GPT + 0x50)
+#define MPC5XXX_GPT5_STATUS (MPC5XXX_GPT + 0x5C)
#define MPC5XXX_GPT5_COUNTER (MPC5XXX_GPT + 0x54)
#define MPC5XXX_GPT6_ENABLE (MPC5XXX_GPT + 0x60)
#define MPC5XXX_GPT6_COUNTER (MPC5XXX_GPT + 0x64)
+#define MPC5XXX_GPT6_STATUS (MPC5XXX_GPT + 0x6C)
#define MPC5XXX_GPT7_ENABLE (MPC5XXX_GPT + 0x70)
#define MPC5XXX_GPT7_COUNTER (MPC5XXX_GPT + 0x74)
+#define MPC5XXX_GPT7_STATUS (MPC5XXX_GPT + 0x7C)
+
+#define MPC5XXX_GPT_GPIO_PIN(status) ((0x00000100 & (status)) >> 8)
#define MPC5XXX_GPT7_PWMCFG (MPC5XXX_GPT + 0x78)
diff --git a/include/ns16550.h b/include/ns16550.h
index 996d915..34888a1 100644
--- a/include/ns16550.h
+++ b/include/ns16550.h
@@ -7,7 +7,7 @@
* added prototypes for ns16550.c
* reduced no of com ports to 2
* modifications (c) Rob Taylor, Flying Pig Systems. 2000.
- *
+ *
* added support for port on 64-bit bus
* by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems
*/
diff --git a/include/pcmcia.h b/include/pcmcia.h
index 43d4510..8f564da 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -308,4 +308,14 @@
#endif /* CFG_CMD_PCMCIA || CFG_CMD_IDE && (CONFIG_IDE_8xx_PCCARD || CONFIG_IDE_8xx_DIRECT) */
+#ifdef CONFIG_8xx
+extern u_int *pcmcia_pgcrx[];
+#define PCMCIA_PGCRX(slot) (*pcmcia_pgcrx[slot])
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD) \
+ || defined(CONFIG_PXA_PCMCIA)
+extern int check_ide_device(int slot);
+#endif
+
#endif /* _PCMCIA_H */
diff --git a/include/ppc440.h b/include/ppc440.h
index 53f14b5..d5a9f66 100644
--- a/include/ppc440.h
+++ b/include/ppc440.h
@@ -25,6 +25,8 @@
/*--------------------------------------------------------------------- */
/* Special Purpose Registers */
/*--------------------------------------------------------------------- */
+#define xer_reg 0x001
+#define lr_reg 0x008
#define dec 0x016 /* decrementer */
#define srr0 0x01a /* save/restore register 0 */
#define srr1 0x01b /* save/restore register 1 */
@@ -37,6 +39,8 @@
#define ivpr 0x03f /* interrupt prefix register */
#define usprg0 0x100 /* user special purpose register general 0 */
#define usprg1 0x110 /* user special purpose register general 1 */
+#define tblr 0x10c /* time base lower, read only */
+#define tbur 0x10d /* time base upper, read only */
#define sprg1 0x111 /* special purpose register general 1 */
#define sprg2 0x112 /* special purpose register general 2 */
#define sprg3 0x113 /* special purpose register general 3 */
@@ -78,7 +82,7 @@
#define ivor13 0x19d /* interrupt vector offset register 13 */
#define ivor14 0x19e /* interrupt vector offset register 14 */
#define ivor15 0x19f /* interrupt vector offset register 15 */
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
#define mcsrr0 0x23a /* machine check save/restore register 0 */
#define mcsrr1 0x23b /* mahcine check save/restore register 1 */
#define mcsr 0x23c /* machine check status register */
@@ -167,12 +171,10 @@
#define sdr_malrbl 0x02a0
#define sdr_maltbs 0x02c0
#define sdr_malrbs 0x02e0
-#define sdr_pci0 0x0300
-#define sdr_usb0 0x0320
+#define sdr_pci0 0x0300
+#define sdr_usb0 0x0320
#define sdr_cust0 0x4000
-#define sdr_sdstp2 0x4001
#define sdr_cust1 0x4002
-#define sdr_sdstp3 0x4003
#define sdr_pfc0 0x4100 /* Pin Function 0 */
#define sdr_pfc1 0x4101 /* Pin Function 1 */
#define sdr_plbtr 0x4200
@@ -212,6 +214,551 @@
#define mem_dlycal 0x0084 /* delay line calibration register */
#define mem_eccesr 0x0098 /* ECC error status */
+#ifdef CONFIG_440GX
+#define sdr_amp 0x0240
+#define sdr_xpllc 0x01c1
+#define sdr_xplld 0x01c2
+#define sdr_xcr 0x01c0
+#define sdr_sdstp2 0x4001
+#define sdr_sdstp3 0x4003
+#endif /* CONFIG_440GX */
+
+#ifdef CONFIG_440SPE
+#undef sdr_sdstp2
+#define sdr_sdstp2 0x0022
+#undef sdr_sdstp3
+#define sdr_sdstp3 0x0023
+#define sdr_ddr0 0x00E1
+#define sdr_uart2 0x0122
+#define sdr_xcr0 0x01c0
+/* #define sdr_xcr1 0x01c3 only one PCIX - SG */
+/* #define sdr_xcr2 0x01c6 only one PCIX - SG */
+#define sdr_xpllc0 0x01c1
+#define sdr_xplld0 0x01c2
+#define sdr_xpllc1 0x01c4 /*notRCW - SG */
+#define sdr_xplld1 0x01c5 /*notRCW - SG */
+#define sdr_xpllc2 0x01c7 /*notRCW - SG */
+#define sdr_xplld2 0x01c8 /*notRCW - SG */
+#define sdr_amp0 0x0240
+#define sdr_amp1 0x0241
+#define sdr_cust2 0x4004
+#define sdr_cust3 0x4006
+#define sdr_sdstp4 0x4001
+#define sdr_sdstp5 0x4003
+#define sdr_sdstp6 0x4005
+#define sdr_sdstp7 0x4007
+
+/*----------------------------------------------------------------------------+
+| Core Configuration/MMU configuration for 440 (CCR1 for 440x5 only).
++----------------------------------------------------------------------------*/
+#define CCR0_PRE 0x40000000
+#define CCR0_CRPE 0x08000000
+#define CCR0_DSTG 0x00200000
+#define CCR0_DAPUIB 0x00100000
+#define CCR0_DTB 0x00008000
+#define CCR0_GICBT 0x00004000
+#define CCR0_GDCBT 0x00002000
+#define CCR0_FLSTA 0x00000100
+#define CCR0_ICSLC_MASK 0x0000000C
+#define CCR0_ICSLT_MASK 0x00000003
+#define CCR1_TCS_MASK 0x00000080
+#define CCR1_TCS_INTCLK 0x00000000
+#define CCR1_TCS_EXTCLK 0x00000080
+#define MMUCR_SEOA 0x01000000
+#define MMUCR_U1TE 0x00400000
+#define MMUCR_U2SWOAE 0x00200000
+#define MMUCR_DULXE 0x00800000
+#define MMUCR_IULXE 0x00400000
+#define MMUCR_STS 0x00100000
+#define MMUCR_STID_MASK 0x000000FF
+
+#define SDR0_CFGADDR 0x00E
+#define SDR0_CFGDATA 0x00F
+
+/******************************************************************************
+ * PCI express defines
+ ******************************************************************************/
+#define SDR0_PE0UTLSET1 0x00000300 /* PE0 Upper transaction layer conf setting */
+#define SDR0_PE0UTLSET2 0x00000301 /* PE0 Upper transaction layer conf setting 2 */
+#define SDR0_PE0DLPSET 0x00000302 /* PE0 Data link & logical physical configuration */
+#define SDR0_PE0LOOP 0x00000303 /* PE0 Loopback interface status */
+#define SDR0_PE0RCSSET 0x00000304 /* PE0 Reset, clock & shutdown setting */
+#define SDR0_PE0RCSSTS 0x00000305 /* PE0 Reset, clock & shutdown status */
+#define SDR0_PE0HSSSET1L0 0x00000306 /* PE0 HSS Control Setting 1: Lane 0 */
+#define SDR0_PE0HSSSET2L0 0x00000307 /* PE0 HSS Control Setting 2: Lane 0 */
+#define SDR0_PE0HSSSTSL0 0x00000308 /* PE0 HSS Control Status : Lane 0 */
+#define SDR0_PE0HSSSET1L1 0x00000309 /* PE0 HSS Control Setting 1: Lane 1 */
+#define SDR0_PE0HSSSET2L1 0x0000030A /* PE0 HSS Control Setting 2: Lane 1 */
+#define SDR0_PE0HSSSTSL1 0x0000030B /* PE0 HSS Control Status : Lane 1 */
+#define SDR0_PE0HSSSET1L2 0x0000030C /* PE0 HSS Control Setting 1: Lane 2 */
+#define SDR0_PE0HSSSET2L2 0x0000030D /* PE0 HSS Control Setting 2: Lane 2 */
+#define SDR0_PE0HSSSTSL2 0x0000030E /* PE0 HSS Control Status : Lane 2 */
+#define SDR0_PE0HSSSET1L3 0x0000030F /* PE0 HSS Control Setting 1: Lane 3 */
+#define SDR0_PE0HSSSET2L3 0x00000310 /* PE0 HSS Control Setting 2: Lane 3 */
+#define SDR0_PE0HSSSTSL3 0x00000311 /* PE0 HSS Control Status : Lane 3 */
+#define SDR0_PE0HSSSET1L4 0x00000312 /* PE0 HSS Control Setting 1: Lane 4 */
+#define SDR0_PE0HSSSET2L4 0x00000313 /* PE0 HSS Control Setting 2: Lane 4 */
+#define SDR0_PE0HSSSTSL4 0x00000314 /* PE0 HSS Control Status : Lane 4 */
+#define SDR0_PE0HSSSET1L5 0x00000315 /* PE0 HSS Control Setting 1: Lane 5 */
+#define SDR0_PE0HSSSET2L5 0x00000316 /* PE0 HSS Control Setting 2: Lane 5 */
+#define SDR0_PE0HSSSTSL5 0x00000317 /* PE0 HSS Control Status : Lane 5 */
+#define SDR0_PE0HSSSET1L6 0x00000318 /* PE0 HSS Control Setting 1: Lane 6 */
+#define SDR0_PE0HSSSET2L6 0x00000319 /* PE0 HSS Control Setting 2: Lane 6 */
+#define SDR0_PE0HSSSTSL6 0x0000031A /* PE0 HSS Control Status : Lane 6 */
+#define SDR0_PE0HSSSET1L7 0x0000031B /* PE0 HSS Control Setting 1: Lane 7 */
+#define SDR0_PE0HSSSET2L7 0x0000031C /* PE0 HSS Control Setting 2: Lane 7 */
+#define SDR0_PE0HSSSTSL7 0x0000031D /* PE0 HSS Control Status : Lane 7 */
+#define SDR0_PE0HSSSEREN 0x0000031E /* PE0 Serdes Transmitter Enable */
+#define SDR0_PE0LANEABCD 0x0000031F /* PE0 Lanes ABCD affectation */
+#define SDR0_PE0LANEEFGH 0x00000320 /* PE0 Lanes EFGH affectation */
+
+#define SDR0_PE1UTLSET1 0x00000340 /* PE1 Upper transaction layer conf setting */
+#define SDR0_PE1UTLSET2 0x00000341 /* PE1 Upper transaction layer conf setting 2 */
+#define SDR0_PE1DLPSET 0x00000342 /* PE1 Data link & logical physical configuration */
+#define SDR0_PE1LOOP 0x00000343 /* PE1 Loopback interface status */
+#define SDR0_PE1RCSSET 0x00000344 /* PE1 Reset, clock & shutdown setting */
+#define SDR0_PE1RCSSTS 0x00000345 /* PE1 Reset, clock & shutdown status */
+#define SDR0_PE1HSSSET1L0 0x00000346 /* PE1 HSS Control Setting 1: Lane 0 */
+#define SDR0_PE1HSSSET2L0 0x00000347 /* PE1 HSS Control Setting 2: Lane 0 */
+#define SDR0_PE1HSSSTSL0 0x00000348 /* PE1 HSS Control Status : Lane 0 */
+#define SDR0_PE1HSSSET1L1 0x00000349 /* PE1 HSS Control Setting 1: Lane 1 */
+#define SDR0_PE1HSSSET2L1 0x0000034A /* PE1 HSS Control Setting 2: Lane 1 */
+#define SDR0_PE1HSSSTSL1 0x0000034B /* PE1 HSS Control Status : Lane 1 */
+#define SDR0_PE1HSSSET1L2 0x0000034C /* PE1 HSS Control Setting 1: Lane 2 */
+#define SDR0_PE1HSSSET2L2 0x0000034D /* PE1 HSS Control Setting 2: Lane 2 */
+#define SDR0_PE1HSSSTSL2 0x0000034E /* PE1 HSS Control Status : Lane 2 */
+#define SDR0_PE1HSSSET1L3 0x0000034F /* PE1 HSS Control Setting 1: Lane 3 */
+#define SDR0_PE1HSSSET2L3 0x00000350 /* PE1 HSS Control Setting 2: Lane 3 */
+#define SDR0_PE1HSSSTSL3 0x00000351 /* PE1 HSS Control Status : Lane 3 */
+#define SDR0_PE1HSSSEREN 0x00000352 /* PE1 Serdes Transmitter Enable */
+#define SDR0_PE1LANEABCD 0x00000353 /* PE1 Lanes ABCD affectation */
+#define SDR0_PE2UTLSET1 0x00000370 /* PE2 Upper transaction layer conf setting */
+#define SDR0_PE2UTLSET2 0x00000371 /* PE2 Upper transaction layer conf setting 2 */
+#define SDR0_PE2DLPSET 0x00000372 /* PE2 Data link & logical physical configuration */
+#define SDR0_PE2LOOP 0x00000373 /* PE2 Loopback interface status */
+#define SDR0_PE2RCSSET 0x00000374 /* PE2 Reset, clock & shutdown setting */
+#define SDR0_PE2RCSSTS 0x00000375 /* PE2 Reset, clock & shutdown status */
+#define SDR0_PE2HSSSET1L0 0x00000376 /* PE2 HSS Control Setting 1: Lane 0 */
+#define SDR0_PE2HSSSET2L0 0x00000377 /* PE2 HSS Control Setting 2: Lane 0 */
+#define SDR0_PE2HSSSTSL0 0x00000378 /* PE2 HSS Control Status : Lane 0 */
+#define SDR0_PE2HSSSET1L1 0x00000379 /* PE2 HSS Control Setting 1: Lane 1 */
+#define SDR0_PE2HSSSET2L1 0x0000037A /* PE2 HSS Control Setting 2: Lane 1 */
+#define SDR0_PE2HSSSTSL1 0x0000037B /* PE2 HSS Control Status : Lane 1 */
+#define SDR0_PE2HSSSET1L2 0x0000037C /* PE2 HSS Control Setting 1: Lane 2 */
+#define SDR0_PE2HSSSET2L2 0x0000037D /* PE2 HSS Control Setting 2: Lane 2 */
+#define SDR0_PE2HSSSTSL2 0x0000037E /* PE2 HSS Control Status : Lane 2 */
+#define SDR0_PE2HSSSET1L3 0x0000037F /* PE2 HSS Control Setting 1: Lane 3 */
+#define SDR0_PE2HSSSET2L3 0x00000380 /* PE2 HSS Control Setting 2: Lane 3 */
+#define SDR0_PE2HSSSTSL3 0x00000381 /* PE2 HSS Control Status : Lane 3 */
+#define SDR0_PE2HSSSEREN 0x00000382 /* PE2 Serdes Transmitter Enable */
+#define SDR0_PE2LANEABCD 0x00000383 /* PE2 Lanes ABCD affectation */
+#define SDR0_PEGPLLSET1 0x000003A0 /* PE Pll LC Tank Setting1 */
+#define SDR0_PEGPLLSET2 0x000003A1 /* PE Pll LC Tank Setting2 */
+#define SDR0_PEGPLLSTS 0x000003A2 /* PE Pll LC Tank Status */
+
+/*----------------------------------------------------------------------------+
+| SDRAM Controller
++----------------------------------------------------------------------------*/
+/*-----------------------------------------------------------------------------+
+| SDRAM DLYCAL Options
++-----------------------------------------------------------------------------*/
+#define SDRAM_DLYCAL_DLCV_MASK 0x000003FC
+#define SDRAM_DLYCAL_DLCV_ENCODE(x) (((x)<<2) & SDRAM_DLYCAL_DLCV_MASK)
+#define SDRAM_DLYCAL_DLCV_DECODE(x) (((x) & SDRAM_DLYCAL_DLCV_MASK)>>2)
+
+/*----------------------------------------------------------------------------+
+| Memory queue defines
++----------------------------------------------------------------------------*/
+/* A REVOIR versus RWC - SG*/
+#define SDRAMQ_DCR_BASE 0x040
+
+#define SDRAM_R0BAS (SDRAMQ_DCR_BASE+0x0) /* rank 0 base address & size */
+#define SDRAM_R1BAS (SDRAMQ_DCR_BASE+0x1) /* rank 1 base address & size */
+#define SDRAM_R2BAS (SDRAMQ_DCR_BASE+0x2) /* rank 2 base address & size */
+#define SDRAM_R3BAS (SDRAMQ_DCR_BASE+0x3) /* rank 3 base address & size */
+#define SDRAM_CONF1HB (SDRAMQ_DCR_BASE+0x5) /* configuration 1 HB */
+#define SDRAM_ERRSTATHB (SDRAMQ_DCR_BASE+0x7) /* error status HB */
+#define SDRAM_ERRADDUHB (SDRAMQ_DCR_BASE+0x8) /* error address upper 32 HB */
+#define SDRAM_ERRADDLHB (SDRAMQ_DCR_BASE+0x9) /* error address lower 32 HB */
+#define SDRAM_PLBADDULL (SDRAMQ_DCR_BASE+0xA) /* PLB base address upper 32 LL */
+#define SDRAM_CONF1LL (SDRAMQ_DCR_BASE+0xB) /* configuration 1 LL */
+#define SDRAM_ERRSTATLL (SDRAMQ_DCR_BASE+0xC) /* error status LL */
+#define SDRAM_ERRADDULL (SDRAMQ_DCR_BASE+0xD) /* error address upper 32 LL */
+#define SDRAM_ERRADDLLL (SDRAMQ_DCR_BASE+0xE) /* error address lower 32 LL */
+#define SDRAM_CONFPATHB (SDRAMQ_DCR_BASE+0xF) /* configuration between paths */
+#define SDRAM_PLBADDUHB (SDRAMQ_DCR_BASE+0x10) /* PLB base address upper 32 LL */
+
+/*-----------------------------------------------------------------------------+
+| Memory Bank 0-7 configuration
++-----------------------------------------------------------------------------*/
+#define SDRAM_RXBAS_SDBA_MASK 0xFF800000 /* Base address */
+#define SDRAM_RXBAS_SDBA_ENCODE(n) ((((unsigned long)(n))&0xFFE00000)>>2)
+#define SDRAM_RXBAS_SDBA_DECODE(n) ((((unsigned long)(n))&0xFFE00000)<<2)
+#define SDRAM_RXBAS_SDSZ_MASK 0x0000FFC0 /* Size */
+#define SDRAM_RXBAS_SDSZ_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<6)
+#define SDRAM_RXBAS_SDSZ_DECODE(n) ((((unsigned long)(n))>>6)&0x3FF)
+#define SDRAM_RXBAS_SDSZ_0 0x00000000 /* 0M */
+#define SDRAM_RXBAS_SDSZ_8 0x0000FFC0 /* 8M */
+#define SDRAM_RXBAS_SDSZ_16 0x0000FF80 /* 16M */
+#define SDRAM_RXBAS_SDSZ_32 0x0000FF00 /* 32M */
+#define SDRAM_RXBAS_SDSZ_64 0x0000FE00 /* 64M */
+#define SDRAM_RXBAS_SDSZ_128 0x0000FC00 /* 128M */
+#define SDRAM_RXBAS_SDSZ_256 0x0000F800 /* 256M */
+#define SDRAM_RXBAS_SDSZ_512 0x0000F000 /* 512M */
+#define SDRAM_RXBAS_SDSZ_1024 0x0000E000 /* 1024M */
+#define SDRAM_RXBAS_SDSZ_2048 0x0000C000 /* 2048M */
+#define SDRAM_RXBAS_SDSZ_4096 0x00008000 /* 4096M */
+
+/*----------------------------------------------------------------------------+
+| Memory controller defines
++----------------------------------------------------------------------------*/
+#define SDRAMC_DCR_BASE 0x010
+#define SDRAMC_CFGADDR (SDRAMC_DCR_BASE+0x0) /* Memory configuration add */
+#define SDRAMC_CFGDATA (SDRAMC_DCR_BASE+0x1) /* Memory configuration data */
+
+/* A REVOIR versus specs 4 bank - SG*/
+#define SDRAM_MCSTAT 0x14 /* memory controller status */
+#define SDRAM_MCOPT1 0x20 /* memory controller options 1 */
+#define SDRAM_MCOPT2 0x21 /* memory controller options 2 */
+#define SDRAM_MODT0 0x22 /* on die termination for bank 0 */
+#define SDRAM_MODT1 0x23 /* on die termination for bank 1 */
+#define SDRAM_MODT2 0x24 /* on die termination for bank 2 */
+#define SDRAM_MODT3 0x25 /* on die termination for bank 3 */
+#define SDRAM_CODT 0x26 /* on die termination for controller */
+#define SDRAM_VVPR 0x27 /* variable VRef programmming */
+#define SDRAM_OPARS 0x28 /* on chip driver control setup */
+#define SDRAM_OPART 0x29 /* on chip driver control trigger */
+#define SDRAM_RTR 0x30 /* refresh timer */
+#define SDRAM_PMIT 0x34 /* power management idle timer */
+#define SDRAM_MB0CF 0x40 /* memory bank 0 configuration */
+#define SDRAM_MB1CF 0x44 /* memory bank 1 configuration */
+#define SDRAM_MB2CF 0x48
+#define SDRAM_MB3CF 0x4C
+#define SDRAM_INITPLR0 0x50 /* manual initialization control */
+#define SDRAM_INITPLR1 0x51 /* manual initialization control */
+#define SDRAM_INITPLR2 0x52 /* manual initialization control */
+#define SDRAM_INITPLR3 0x53 /* manual initialization control */
+#define SDRAM_INITPLR4 0x54 /* manual initialization control */
+#define SDRAM_INITPLR5 0x55 /* manual initialization control */
+#define SDRAM_INITPLR6 0x56 /* manual initialization control */
+#define SDRAM_INITPLR7 0x57 /* manual initialization control */
+#define SDRAM_INITPLR8 0x58 /* manual initialization control */
+#define SDRAM_INITPLR9 0x59 /* manual initialization control */
+#define SDRAM_INITPLR10 0x5a /* manual initialization control */
+#define SDRAM_INITPLR11 0x5b /* manual initialization control */
+#define SDRAM_INITPLR12 0x5c /* manual initialization control */
+#define SDRAM_INITPLR13 0x5d /* manual initialization control */
+#define SDRAM_INITPLR14 0x5e /* manual initialization control */
+#define SDRAM_INITPLR15 0x5f /* manual initialization control */
+#define SDRAM_RQDC 0x70 /* read DQS delay control */
+#define SDRAM_RFDC 0x74 /* read feedback delay control */
+#define SDRAM_RDCC 0x78 /* read data capture control */
+#define SDRAM_DLCR 0x7A /* delay line calibration */
+#define SDRAM_CLKTR 0x80 /* DDR clock timing */
+#define SDRAM_WRDTR 0x81 /* write data, DQS, DM clock, timing */
+#define SDRAM_SDTR1 0x85 /* DDR SDRAM timing 1 */
+#define SDRAM_SDTR2 0x86 /* DDR SDRAM timing 2 */
+#define SDRAM_SDTR3 0x87 /* DDR SDRAM timing 3 */
+#define SDRAM_MMODE 0x88 /* memory mode */
+#define SDRAM_MEMODE 0x89 /* memory extended mode */
+#define SDRAM_ECCCR 0x98 /* ECC error status */
+#define SDRAM_CID 0xA4 /* core ID */
+#define SDRAM_RID 0xA8 /* revision ID */
+
+/*-----------------------------------------------------------------------------+
+| Memory Controller Status
++-----------------------------------------------------------------------------*/
+#define SDRAM_MCSTAT_MIC_MASK 0x80000000 /* Memory init status mask */
+#define SDRAM_MCSTAT_MIC_NOTCOMP 0x00000000 /* Mem init not complete */
+#define SDRAM_MCSTAT_MIC_COMP 0x80000000 /* Mem init complete */
+#define SDRAM_MCSTAT_SRMS_MASK 0x80000000 /* Mem self refresh stat mask */
+#define SDRAM_MCSTAT_SRMS_NOT_SF 0x00000000 /* Mem not in self refresh */
+#define SDRAM_MCSTAT_SRMS_SF 0x80000000 /* Mem in self refresh */
+
+/*-----------------------------------------------------------------------------+
+| Memory Controller Options 1
++-----------------------------------------------------------------------------*/
+#define SDRAM_MCOPT1_MCHK_MASK 0x30000000 /* Memory data err check mask*/
+#define SDRAM_MCOPT1_MCHK_NON 0x00000000 /* No ECC generation */
+#define SDRAM_MCOPT1_MCHK_GEN 0x20000000 /* ECC generation */
+#define SDRAM_MCOPT1_MCHK_CHK 0x10000000 /* ECC generation and check */
+#define SDRAM_MCOPT1_MCHK_CHK_REP 0x30000000 /* ECC generation, chk, report*/
+#define SDRAM_MCOPT1_MCHK_CHK_DECODE(n) ((((unsigned long)(n))>>28)&0x3)
+#define SDRAM_MCOPT1_RDEN_MASK 0x08000000 /* Registered DIMM mask */
+#define SDRAM_MCOPT1_RDEN 0x08000000 /* Registered DIMM enable */
+#define SDRAM_MCOPT1_PMU_MASK 0x06000000 /* Page management unit mask */
+#define SDRAM_MCOPT1_PMU_CLOSE 0x00000000 /* PMU Close */
+#define SDRAM_MCOPT1_PMU_OPEN 0x04000000 /* PMU Open */
+#define SDRAM_MCOPT1_PMU_AUTOCLOSE 0x02000000 /* PMU AutoClose */
+#define SDRAM_MCOPT1_DMWD_MASK 0x01000000 /* DRAM width mask */
+#define SDRAM_MCOPT1_DMWD_32 0x00000000 /* 32 bits */
+#define SDRAM_MCOPT1_DMWD_64 0x01000000 /* 64 bits */
+#define SDRAM_MCOPT1_UIOS_MASK 0x00C00000 /* Unused IO State */
+#define SDRAM_MCOPT1_BCNT_MASK 0x00200000 /* Bank count */
+#define SDRAM_MCOPT1_4_BANKS 0x00000000 /* 4 Banks */
+#define SDRAM_MCOPT1_8_BANKS 0x00200000 /* 8 Banks */
+#define SDRAM_MCOPT1_DDR_TYPE_MASK 0x00100000 /* DDR Memory Type mask */
+#define SDRAM_MCOPT1_DDR1_TYPE 0x00000000 /* DDR1 Memory Type */
+#define SDRAM_MCOPT1_DDR2_TYPE 0x00100000 /* DDR2 Memory Type */
+#define SDRAM_MCOPT1_QDEP 0x00020000 /* 4 commands deep */
+#define SDRAM_MCOPT1_RWOO_MASK 0x00008000 /* Out of Order Read mask */
+#define SDRAM_MCOPT1_RWOO_DISABLED 0x00000000 /* disabled */
+#define SDRAM_MCOPT1_RWOO_ENABLED 0x00008000 /* enabled */
+#define SDRAM_MCOPT1_WOOO_MASK 0x00004000 /* Out of Order Write mask */
+#define SDRAM_MCOPT1_WOOO_DISABLED 0x00000000 /* disabled */
+#define SDRAM_MCOPT1_WOOO_ENABLED 0x00004000 /* enabled */
+#define SDRAM_MCOPT1_DCOO_MASK 0x00002000 /* All Out of Order mask */
+#define SDRAM_MCOPT1_DCOO_DISABLED 0x00002000 /* disabled */
+#define SDRAM_MCOPT1_DCOO_ENABLED 0x00000000 /* enabled */
+#define SDRAM_MCOPT1_DREF_MASK 0x00001000 /* Deferred refresh mask */
+#define SDRAM_MCOPT1_DREF_NORMAL 0x00000000 /* normal refresh */
+#define SDRAM_MCOPT1_DREF_DEFER_4 0x00001000 /* defer up to 4 refresh cmd */
+
+/*-----------------------------------------------------------------------------+
+| Memory Controller Options 2
++-----------------------------------------------------------------------------*/
+#define SDRAM_MCOPT2_SREN_MASK 0x80000000 /* Self Test mask */
+#define SDRAM_MCOPT2_SREN_EXIT 0x00000000 /* Self Test exit */
+#define SDRAM_MCOPT2_SREN_ENTER 0x80000000 /* Self Test enter */
+#define SDRAM_MCOPT2_PMEN_MASK 0x40000000 /* Power Management mask */
+#define SDRAM_MCOPT2_PMEN_DISABLE 0x00000000 /* disable */
+#define SDRAM_MCOPT2_PMEN_ENABLE 0x40000000 /* enable */
+#define SDRAM_MCOPT2_IPTR_MASK 0x20000000 /* Init Trigger Reg mask */
+#define SDRAM_MCOPT2_IPTR_IDLE 0x00000000 /* idle */
+#define SDRAM_MCOPT2_IPTR_EXECUTE 0x20000000 /* execute preloaded init */
+#define SDRAM_MCOPT2_XSRP_MASK 0x10000000 /* Exit Self Refresh Prevent */
+#define SDRAM_MCOPT2_XSRP_ALLOW 0x00000000 /* allow self refresh exit */
+#define SDRAM_MCOPT2_XSRP_PREVENT 0x10000000 /* prevent self refresh exit */
+#define SDRAM_MCOPT2_DCEN_MASK 0x08000000 /* SDRAM Controller Enable */
+#define SDRAM_MCOPT2_DCEN_DISABLE 0x00000000 /* SDRAM Controller Enable */
+#define SDRAM_MCOPT2_DCEN_ENABLE 0x08000000 /* SDRAM Controller Enable */
+#define SDRAM_MCOPT2_ISIE_MASK 0x04000000 /* Init Seq Interruptable mas*/
+#define SDRAM_MCOPT2_ISIE_DISABLE 0x00000000 /* disable */
+#define SDRAM_MCOPT2_ISIE_ENABLE 0x04000000 /* enable */
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Refresh Timer Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_RTR_RINT_MASK 0xFFF80000
+#define SDRAM_RTR_RINT_ENCODE(n) ((((unsigned long)(n))&0xFFF8)<<16)
+#define SDRAM_RTR_RINT_DECODE(n) ((((unsigned long)(n))>>16)&0xFFF8)
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Read DQS Delay Control Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_RQDC_RQDE_MASK 0x80000000
+#define SDRAM_RQDC_RQDE_DISABLE 0x00000000
+#define SDRAM_RQDC_RQDE_ENABLE 0x80000000
+#define SDRAM_RQDC_RQFD_MASK 0x000001FF
+#define SDRAM_RQDC_RQFD_ENCODE(n) ((((unsigned long)(n))&0x1FF)<<0)
+
+#define SDRAM_RQDC_RQFD_MAX 0x1FF
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Read Data Capture Control Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_RDCC_RDSS_MASK 0xC0000000
+#define SDRAM_RDCC_RDSS_T1 0x00000000
+#define SDRAM_RDCC_RDSS_T2 0x40000000
+#define SDRAM_RDCC_RDSS_T3 0x80000000
+#define SDRAM_RDCC_RDSS_T4 0xC0000000
+#define SDRAM_RDCC_RSAE_MASK 0x00000001
+#define SDRAM_RDCC_RSAE_DISABLE 0x00000001
+#define SDRAM_RDCC_RSAE_ENABLE 0x00000000
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Read Feedback Delay Control Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_RFDC_ARSE_MASK 0x80000000
+#define SDRAM_RFDC_ARSE_DISABLE 0x80000000
+#define SDRAM_RFDC_ARSE_ENABLE 0x00000000
+#define SDRAM_RFDC_RFOS_MASK 0x007F0000
+#define SDRAM_RFDC_RFOS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16)
+#define SDRAM_RFDC_RFFD_MASK 0x000003FF
+#define SDRAM_RFDC_RFFD_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0)
+
+#define SDRAM_RFDC_RFFD_MAX 0x7FF
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Delay Line Calibration Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_DLCR_DCLM_MASK 0x80000000
+#define SDRAM_DLCR_DCLM_MANUEL 0x80000000
+#define SDRAM_DLCR_DCLM_AUTO 0x00000000
+#define SDRAM_DLCR_DLCR_MASK 0x08000000
+#define SDRAM_DLCR_DLCR_CALIBRATE 0x08000000
+#define SDRAM_DLCR_DLCR_IDLE 0x00000000
+#define SDRAM_DLCR_DLCS_MASK 0x07000000
+#define SDRAM_DLCR_DLCS_NOT_RUN 0x00000000
+#define SDRAM_DLCR_DLCS_IN_PROGRESS 0x01000000
+#define SDRAM_DLCR_DLCS_COMPLETE 0x02000000
+#define SDRAM_DLCR_DLCS_CONT_DONE 0x03000000
+#define SDRAM_DLCR_DLCS_ERROR 0x04000000
+#define SDRAM_DLCR_DLCV_MASK 0x000001FF
+#define SDRAM_DLCR_DLCV_ENCODE(n) ((((unsigned long)(n))&0x1FF)<<0)
+#define SDRAM_DLCR_DLCV_DECODE(n) ((((unsigned long)(n))>>0)&0x1FF)
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Controller On Die Termination Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_CODT_ODT_ON 0x80000000
+#define SDRAM_CODT_ODT_OFF 0x00000000
+#define SDRAM_CODT_DQS_VOLTAGE_DDR_MASK 0x00000020
+#define SDRAM_CODT_DQS_2_5_V_DDR1 0x00000000
+#define SDRAM_CODT_DQS_1_8_V_DDR2 0x00000020
+#define SDRAM_CODT_DQS_MASK 0x00000010
+#define SDRAM_CODT_DQS_DIFFERENTIAL 0x00000000
+#define SDRAM_CODT_DQS_SINGLE_END 0x00000010
+#define SDRAM_CODT_CKSE_DIFFERENTIAL 0x00000000
+#define SDRAM_CODT_CKSE_SINGLE_END 0x00000008
+#define SDRAM_CODT_FEEBBACK_RCV_SINGLE_END 0x00000004
+#define SDRAM_CODT_FEEBBACK_DRV_SINGLE_END 0x00000002
+#define SDRAM_CODT_IO_HIZ 0x00000000
+#define SDRAM_CODT_IO_NMODE 0x00000001
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Mode Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_MMODE_WR_MASK 0x00000E00
+#define SDRAM_MMODE_WR_DDR1 0x00000000
+#define SDRAM_MMODE_WR_DDR2_3_CYC 0x00000400
+#define SDRAM_MMODE_WR_DDR2_4_CYC 0x00000600
+#define SDRAM_MMODE_WR_DDR2_5_CYC 0x00000800
+#define SDRAM_MMODE_WR_DDR2_6_CYC 0x00000A00
+#define SDRAM_MMODE_DCL_MASK 0x00000070
+#define SDRAM_MMODE_DCL_DDR1_2_0_CLK 0x00000020
+#define SDRAM_MMODE_DCL_DDR1_2_5_CLK 0x00000060
+#define SDRAM_MMODE_DCL_DDR1_3_0_CLK 0x00000030
+#define SDRAM_MMODE_DCL_DDR2_2_0_CLK 0x00000020
+#define SDRAM_MMODE_DCL_DDR2_3_0_CLK 0x00000030
+#define SDRAM_MMODE_DCL_DDR2_4_0_CLK 0x00000040
+#define SDRAM_MMODE_DCL_DDR2_5_0_CLK 0x00000050
+#define SDRAM_MMODE_DCL_DDR2_6_0_CLK 0x00000060
+#define SDRAM_MMODE_DCL_DDR2_7_0_CLK 0x00000070
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Extended Mode Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_MEMODE_DIC_MASK 0x00000002
+#define SDRAM_MEMODE_DIC_NORMAL 0x00000000
+#define SDRAM_MEMODE_DIC_WEAK 0x00000002
+#define SDRAM_MEMODE_DLL_MASK 0x00000001
+#define SDRAM_MEMODE_DLL_DISABLE 0x00000001
+#define SDRAM_MEMODE_DLL_ENABLE 0x00000000
+#define SDRAM_MEMODE_RTT_MASK 0x00000044
+#define SDRAM_MEMODE_RTT_DISABLED 0x00000000
+#define SDRAM_MEMODE_RTT_75OHM 0x00000004
+#define SDRAM_MEMODE_RTT_150OHM 0x00000040
+#define SDRAM_MEMODE_DQS_MASK 0x00000400
+#define SDRAM_MEMODE_DQS_DISABLE 0x00000400
+#define SDRAM_MEMODE_DQS_ENABLE 0x00000000
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Clock Timing Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_CLKTR_CLKP_MASK 0xC0000000
+#define SDRAM_CLKTR_CLKP_0_DEG 0x00000000
+#define SDRAM_CLKTR_CLKP_180_DEG_ADV 0x80000000
+
+/*-----------------------------------------------------------------------------+
+| SDRAM Write Timing Register
++-----------------------------------------------------------------------------*/
+#define SDRAM_WRDTR_LLWP_MASK 0x10000000
+#define SDRAM_WRDTR_LLWP_DIS 0x10000000
+#define SDRAM_WRDTR_LLWP_1_CYC 0x00000000
+#define SDRAM_WRDTR_WTR_MASK 0x0E000000
+#define SDRAM_WRDTR_WTR_0_DEG 0x06000000
+#define SDRAM_WRDTR_WTR_180_DEG_ADV 0x02000000
+#define SDRAM_WRDTR_WTR_270_DEG_ADV 0x00000000
+
+/*-----------------------------------------------------------------------------+
+| SDRAM SDTR1 Options
++-----------------------------------------------------------------------------*/
+#define SDRAM_SDTR1_LDOF_MASK 0x80000000
+#define SDRAM_SDTR1_LDOF_1_CLK 0x00000000
+#define SDRAM_SDTR1_LDOF_2_CLK 0x80000000
+#define SDRAM_SDTR1_RTW_MASK 0x00F00000
+#define SDRAM_SDTR1_RTW_2_CLK 0x00200000
+#define SDRAM_SDTR1_RTW_3_CLK 0x00300000
+#define SDRAM_SDTR1_WTWO_MASK 0x000F0000
+#define SDRAM_SDTR1_WTWO_0_CLK 0x00000000
+#define SDRAM_SDTR1_WTWO_1_CLK 0x00010000
+#define SDRAM_SDTR1_RTRO_MASK 0x0000F000
+#define SDRAM_SDTR1_RTRO_1_CLK 0x00001000
+#define SDRAM_SDTR1_RTRO_2_CLK 0x00002000
+
+/*-----------------------------------------------------------------------------+
+| SDRAM SDTR2 Options
++-----------------------------------------------------------------------------*/
+#define SDRAM_SDTR2_RCD_MASK 0xF0000000
+#define SDRAM_SDTR2_RCD_1_CLK 0x10000000
+#define SDRAM_SDTR2_RCD_2_CLK 0x20000000
+#define SDRAM_SDTR2_RCD_3_CLK 0x30000000
+#define SDRAM_SDTR2_RCD_4_CLK 0x40000000
+#define SDRAM_SDTR2_RCD_5_CLK 0x50000000
+#define SDRAM_SDTR2_WTR_MASK 0x0F000000
+#define SDRAM_SDTR2_WTR_1_CLK 0x01000000
+#define SDRAM_SDTR2_WTR_2_CLK 0x02000000
+#define SDRAM_SDTR2_WTR_3_CLK 0x03000000
+#define SDRAM_SDTR2_WTR_4_CLK 0x04000000
+#define SDRAM_SDTR3_WTR_ENCODE(n) ((((unsigned long)(n))&0xF)<<24)
+#define SDRAM_SDTR2_XSNR_MASK 0x00FF0000
+#define SDRAM_SDTR2_XSNR_8_CLK 0x00080000
+#define SDRAM_SDTR2_XSNR_16_CLK 0x00100000
+#define SDRAM_SDTR2_XSNR_32_CLK 0x00200000
+#define SDRAM_SDTR2_XSNR_64_CLK 0x00400000
+#define SDRAM_SDTR2_WPC_MASK 0x0000F000
+#define SDRAM_SDTR2_WPC_2_CLK 0x00002000
+#define SDRAM_SDTR2_WPC_3_CLK 0x00003000
+#define SDRAM_SDTR2_WPC_4_CLK 0x00004000
+#define SDRAM_SDTR2_WPC_5_CLK 0x00005000
+#define SDRAM_SDTR2_WPC_6_CLK 0x00006000
+#define SDRAM_SDTR3_WPC_ENCODE(n) ((((unsigned long)(n))&0xF)<<12)
+#define SDRAM_SDTR2_RPC_MASK 0x00000F00
+#define SDRAM_SDTR2_RPC_2_CLK 0x00000200
+#define SDRAM_SDTR2_RPC_3_CLK 0x00000300
+#define SDRAM_SDTR2_RPC_4_CLK 0x00000400
+#define SDRAM_SDTR2_RP_MASK 0x000000F0
+#define SDRAM_SDTR2_RP_3_CLK 0x00000030
+#define SDRAM_SDTR2_RP_4_CLK 0x00000040
+#define SDRAM_SDTR2_RP_5_CLK 0x00000050
+#define SDRAM_SDTR2_RP_6_CLK 0x00000060
+#define SDRAM_SDTR2_RP_7_CLK 0x00000070
+#define SDRAM_SDTR2_RRD_MASK 0x0000000F
+#define SDRAM_SDTR2_RRD_2_CLK 0x00000002
+#define SDRAM_SDTR2_RRD_3_CLK 0x00000003
+
+/*-----------------------------------------------------------------------------+
+| SDRAM SDTR3 Options
++-----------------------------------------------------------------------------*/
+#define SDRAM_SDTR3_RAS_MASK 0x1F000000
+#define SDRAM_SDTR3_RAS_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24)
+#define SDRAM_SDTR3_RC_MASK 0x001F0000
+#define SDRAM_SDTR3_RC_ENCODE(n) ((((unsigned long)(n))&0x1F)<<16)
+#define SDRAM_SDTR3_XCS_MASK 0x00001F00
+#define SDRAM_SDTR3_XCS 0x00000D00
+#define SDRAM_SDTR3_RFC_MASK 0x0000003F
+#define SDRAM_SDTR3_RFC_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0)
+
+/*-----------------------------------------------------------------------------+
+| Memory Bank 0-1 configuration
++-----------------------------------------------------------------------------*/
+#define SDRAM_BXCF_M_AM_MASK 0x00000F00 /* Addressing mode */
+#define SDRAM_BXCF_M_AM_0 0x00000000 /* Mode 0 */
+#define SDRAM_BXCF_M_AM_1 0x00000100 /* Mode 1 */
+#define SDRAM_BXCF_M_AM_2 0x00000200 /* Mode 2 */
+#define SDRAM_BXCF_M_AM_3 0x00000300 /* Mode 3 */
+#define SDRAM_BXCF_M_AM_4 0x00000400 /* Mode 4 */
+#define SDRAM_BXCF_M_AM_5 0x00000500 /* Mode 5 */
+#define SDRAM_BXCF_M_AM_6 0x00000600 /* Mode 6 */
+#define SDRAM_BXCF_M_AM_7 0x00000700 /* Mode 7 */
+#define SDRAM_BXCF_M_AM_8 0x00000800 /* Mode 8 */
+#define SDRAM_BXCF_M_AM_9 0x00000900 /* Mode 9 */
+#define SDRAM_BXCF_M_BE_MASK 0x00000001 /* Memory Bank Enable */
+#define SDRAM_BXCF_M_BE_DISABLE 0x00000000 /* Memory Bank Enable */
+#define SDRAM_BXCF_M_BE_ENABLE 0x00000001 /* Memory Bank Enable */
+#endif /* CONFIG_440SPE */
+
/*-----------------------------------------------------------------------------
| External Bus Controller
+----------------------------------------------------------------------------*/
@@ -503,7 +1050,7 @@
/*-----------------------------------------------------------------------------
| L2 Cache
+----------------------------------------------------------------------------*/
-#if defined (CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined (CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
#define L2_CACHE_BASE 0x030
#define l2_cache_cfg (L2_CACHE_BASE+0x00) /* L2 Cache Config */
#define l2_cache_cmd (L2_CACHE_BASE+0x01) /* L2 Cache Command */
@@ -526,7 +1073,7 @@
| Clocking, Power Management and Chip Control
+----------------------------------------------------------------------------*/
#define CNTRL_DCR_BASE 0x0b0
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
#define cpc0_er (CNTRL_DCR_BASE+0x00) /* CPM enable register */
#define cpc0_fr (CNTRL_DCR_BASE+0x01) /* CPM force register */
#define cpc0_sr (CNTRL_DCR_BASE+0x02) /* CPM status register */
@@ -574,6 +1121,30 @@
#define uic1vr (UIC1_DCR_BASE+0x7) /* UIC1 vector */
#define uic1vcr (UIC1_DCR_BASE+0x8) /* UIC1 vector configuration */
+#if defined(CONFIG_440SPE)
+#define UIC2_DCR_BASE 0xe0
+#define uic2sr (UIC0_DCR_BASE+0x0) /* UIC2 status-Read Clear */
+#define uic2srs (UIC0_DCR_BASE+0x1) /* UIC2 status-Read Set */
+#define uic2er (UIC0_DCR_BASE+0x2) /* UIC2 enable */
+#define uic2cr (UIC0_DCR_BASE+0x3) /* UIC2 critical */
+#define uic2pr (UIC0_DCR_BASE+0x4) /* UIC2 polarity */
+#define uic2tr (UIC0_DCR_BASE+0x5) /* UIC2 triggering */
+#define uic2msr (UIC0_DCR_BASE+0x6) /* UIC2 masked status */
+#define uic2vr (UIC0_DCR_BASE+0x7) /* UIC2 vector */
+#define uic2vcr (UIC0_DCR_BASE+0x8) /* UIC2 vector configuration */
+
+#define UIC3_DCR_BASE 0xf0
+#define uic3sr (UIC1_DCR_BASE+0x0) /* UIC3 status-Read Clear */
+#define uic3srs (UIC0_DCR_BASE+0x1) /* UIC3 status-Read Set */
+#define uic3er (UIC1_DCR_BASE+0x2) /* UIC3 enable */
+#define uic3cr (UIC1_DCR_BASE+0x3) /* UIC3 critical */
+#define uic3pr (UIC1_DCR_BASE+0x4) /* UIC3 polarity */
+#define uic3tr (UIC1_DCR_BASE+0x5) /* UIC3 triggering */
+#define uic3msr (UIC1_DCR_BASE+0x6) /* UIC3 masked status */
+#define uic3vr (UIC1_DCR_BASE+0x7) /* UIC3 vector */
+#define uic3vcr (UIC1_DCR_BASE+0x8) /* UIC3 vector configuration */
+#endif /* CONFIG_440SPE */
+
#if defined(CONFIG_440GX)
#define UIC2_DCR_BASE 0x210
#define uic2sr (UIC2_DCR_BASE+0x0) /* UIC2 status */
@@ -607,6 +1178,103 @@
#define uicvr uic0vr
#define uicvcr uic0vcr
+#if defined(CONFIG_440SPE)
+/*----------------------------------------------------------------------------+
+| Clock / Power-on-reset DCR's.
++----------------------------------------------------------------------------*/
+#define CPR0_CFGADDR 0x00C
+#define CPR0_CFGDATA 0x00D
+
+#define CPR0_CLKUPD 0x20
+#define CPR0_CLKUPD_BSY_MASK 0x80000000
+#define CPR0_CLKUPD_BSY_COMPLETED 0x00000000
+#define CPR0_CLKUPD_BSY_BUSY 0x80000000
+#define CPR0_CLKUPD_CUI_MASK 0x80000000
+#define CPR0_CLKUPD_CUI_DISABLE 0x00000000
+#define CPR0_CLKUPD_CUI_ENABLE 0x80000000
+#define CPR0_CLKUPD_CUD_MASK 0x40000000
+#define CPR0_CLKUPD_CUD_DISABLE 0x00000000
+#define CPR0_CLKUPD_CUD_ENABLE 0x40000000
+
+#define CPR0_PLLC 0x40
+#define CPR0_PLLC_RST_MASK 0x80000000
+#define CPR0_PLLC_RST_PLLLOCKED 0x00000000
+#define CPR0_PLLC_RST_PLLRESET 0x80000000
+#define CPR0_PLLC_ENG_MASK 0x40000000
+#define CPR0_PLLC_ENG_DISABLE 0x00000000
+#define CPR0_PLLC_ENG_ENABLE 0x40000000
+#define CPR0_PLLC_ENG_ENCODE(n) ((((unsigned long)(n))&0x01)<<30)
+#define CPR0_PLLC_ENG_DECODE(n) ((((unsigned long)(n))>>30)&0x01)
+#define CPR0_PLLC_SRC_MASK 0x20000000
+#define CPR0_PLLC_SRC_PLLOUTA 0x00000000
+#define CPR0_PLLC_SRC_PLLOUTB 0x20000000
+#define CPR0_PLLC_SRC_ENCODE(n) ((((unsigned long)(n))&0x01)<<29)
+#define CPR0_PLLC_SRC_DECODE(n) ((((unsigned long)(n))>>29)&0x01)
+#define CPR0_PLLC_SEL_MASK 0x07000000
+#define CPR0_PLLC_SEL_PLLOUT 0x00000000
+#define CPR0_PLLC_SEL_CPU 0x01000000
+#define CPR0_PLLC_SEL_EBC 0x05000000
+#define CPR0_PLLC_SEL_ENCODE(n) ((((unsigned long)(n))&0x07)<<24)
+#define CPR0_PLLC_SEL_DECODE(n) ((((unsigned long)(n))>>24)&0x07)
+#define CPR0_PLLC_TUNE_MASK 0x000003FF
+#define CPR0_PLLC_TUNE_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0)
+#define CPR0_PLLC_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF)
+
+#define CPR0_PLLD 0x60
+#define CPR0_PLLD_FBDV_MASK 0x1F000000
+#define CPR0_PLLD_FBDV_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24)
+#define CPR0_PLLD_FBDV_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x1F)+1)
+#define CPR0_PLLD_FWDVA_MASK 0x000F0000
+#define CPR0_PLLD_FWDVA_ENCODE(n) ((((unsigned long)(n))&0x0F)<<16)
+#define CPR0_PLLD_FWDVA_DECODE(n) ((((((unsigned long)(n))>>16)-1)&0x0F)+1)
+#define CPR0_PLLD_FWDVB_MASK 0x00000700
+#define CPR0_PLLD_FWDVB_ENCODE(n) ((((unsigned long)(n))&0x07)<<8)
+#define CPR0_PLLD_FWDVB_DECODE(n) ((((((unsigned long)(n))>>8)-1)&0x07)+1)
+#define CPR0_PLLD_LFBDV_MASK 0x0000003F
+#define CPR0_PLLD_LFBDV_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0)
+#define CPR0_PLLD_LFBDV_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0x3F)+1)
+
+#define CPR0_PRIMAD 0x80
+#define CPR0_PRIMAD_PRADV0_MASK 0x07000000
+#define CPR0_PRIMAD_PRADV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24)
+#define CPR0_PRIMAD_PRADV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1)
+
+#define CPR0_PRIMBD 0xA0
+#define CPR0_PRIMBD_PRBDV0_MASK 0x07000000
+#define CPR0_PRIMBD_PRBDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24)
+#define CPR0_PRIMBD_PRBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1)
+
+#define CPR0_OPBD 0xC0
+#define CPR0_OPBD_OPBDV0_MASK 0x03000000
+#define CPR0_OPBD_OPBDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24)
+#define CPR0_OPBD_OPBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1)
+
+#define CPR0_PERD 0xE0
+#define CPR0_PERD_PERDV0_MASK 0x03000000
+#define CPR0_PERD_PERDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24)
+#define CPR0_PERD_PERDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1)
+
+#define CPR0_MALD 0x100
+#define CPR0_MALD_MALDV0_MASK 0x03000000
+#define CPR0_MALD_MALDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24)
+#define CPR0_MALD_MALDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1)
+
+#define CPR0_ICFG 0x140
+#define CPR0_ICFG_RLI_MASK 0x80000000
+#define CPR0_ICFG_RLI_RESETCPR 0x00000000
+#define CPR0_ICFG_RLI_PRESERVECPR 0x80000000
+#define CPR0_ICFG_ICS_MASK 0x00000007
+#define CPR0_ICFG_ICS_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0)
+#define CPR0_ICFG_ICS_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0x3F)+1)
+
+/************************/
+/* IIC defines */
+/************************/
+#define IIC0_MMIO_BASE 0xA0000400
+#define IIC1_MMIO_BASE 0xA0000500
+
+#endif /* CONFIG_440SP */
+
/*-----------------------------------------------------------------------------
| DMA
+----------------------------------------------------------------------------*/
@@ -722,7 +1390,7 @@
#define UIC_GPTCT 0x00000004 /* GPT count timer */
#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */
#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */
-#else /* CONFIG_440SP */
+#elif defined(CONFIG_440GX) || defined(CONFIG_440EP)
#define UIC_U0 0x80000000 /* UART 0 */
#define UIC_U1 0x40000000 /* UART 1 */
#define UIC_IIC0 0x20000000 /* IIC */
@@ -755,7 +1423,40 @@
#define UIC_EIR6 0x00000004 /* External interrupt 6 */
#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */
#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */
-#endif /* CONFIG_440SP */
+#elif !defined(CONFIG_440SPE)
+#define UIC_U0 0x80000000 /* UART 0 */
+#define UIC_U1 0x40000000 /* UART 1 */
+#define UIC_IIC0 0x20000000 /* IIC */
+#define UIC_IIC1 0x10000000 /* IIC */
+#define UIC_PIM 0x08000000 /* PCI inbound message */
+#define UIC_PCRW 0x04000000 /* PCI command register write */
+#define UIC_PPM 0x02000000 /* PCI power management */
+#define UIC_MSI0 0x01000000 /* PCI MSI level 0 */
+#define UIC_MSI1 0x00800000 /* PCI MSI level 1 */
+#define UIC_MSI2 0x00400000 /* PCI MSI level 2 */
+#define UIC_MTE 0x00200000 /* MAL TXEOB */
+#define UIC_MRE 0x00100000 /* MAL RXEOB */
+#define UIC_D0 0x00080000 /* DMA channel 0 */
+#define UIC_D1 0x00040000 /* DMA channel 1 */
+#define UIC_D2 0x00020000 /* DMA channel 2 */
+#define UIC_D3 0x00010000 /* DMA channel 3 */
+#define UIC_RSVD0 0x00008000 /* Reserved */
+#define UIC_RSVD1 0x00004000 /* Reserved */
+#define UIC_CT0 0x00002000 /* GPT compare timer 0 */
+#define UIC_CT1 0x00001000 /* GPT compare timer 1 */
+#define UIC_CT2 0x00000800 /* GPT compare timer 2 */
+#define UIC_CT3 0x00000400 /* GPT compare timer 3 */
+#define UIC_CT4 0x00000200 /* GPT compare timer 4 */
+#define UIC_EIR0 0x00000100 /* External interrupt 0 */
+#define UIC_EIR1 0x00000080 /* External interrupt 1 */
+#define UIC_EIR2 0x00000040 /* External interrupt 2 */
+#define UIC_EIR3 0x00000020 /* External interrupt 3 */
+#define UIC_EIR4 0x00000010 /* External interrupt 4 */
+#define UIC_EIR5 0x00000008 /* External interrupt 5 */
+#define UIC_EIR6 0x00000004 /* External interrupt 6 */
+#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */
+#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */
+#endif /* CONFIG_440GX */
/* For compatibility with 405 code */
#define UIC_MAL_TXEOB UIC_MTE
@@ -797,7 +1498,40 @@
#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */
#define UIC_ETH1 0x00000002 /* Reserved */
#define UIC_XOR 0x00000001 /* XOR */
-#else /* CONFIG_440SP */
+#elif defined(CONFIG_440GX) || defined(CONFIG_440EP)
+#define UIC_MS 0x80000000 /* MAL SERR */
+#define UIC_MTDE 0x40000000 /* MAL TXDE */
+#define UIC_MRDE 0x20000000 /* MAL RXDE */
+#define UIC_DEUE 0x10000000 /* DDR SDRAM ECC uncorrectible error*/
+#define UIC_DECE 0x08000000 /* DDR SDRAM correctible error */
+#define UIC_EBCO 0x04000000 /* EBCO interrupt status */
+#define UIC_EBMI 0x02000000 /* EBMI interrupt status */
+#define UIC_OPB 0x01000000 /* OPB to PLB bridge interrupt stat */
+#define UIC_MSI3 0x00800000 /* PCI MSI level 3 */
+#define UIC_MSI4 0x00400000 /* PCI MSI level 4 */
+#define UIC_MSI5 0x00200000 /* PCI MSI level 5 */
+#define UIC_MSI6 0x00100000 /* PCI MSI level 6 */
+#define UIC_MSI7 0x00080000 /* PCI MSI level 7 */
+#define UIC_MSI8 0x00040000 /* PCI MSI level 8 */
+#define UIC_MSI9 0x00020000 /* PCI MSI level 9 */
+#define UIC_MSI10 0x00010000 /* PCI MSI level 10 */
+#define UIC_MSI11 0x00008000 /* PCI MSI level 11 */
+#define UIC_PPMI 0x00004000 /* PPM interrupt status */
+#define UIC_EIR7 0x00002000 /* External interrupt 7 */
+#define UIC_EIR8 0x00001000 /* External interrupt 8 */
+#define UIC_EIR9 0x00000800 /* External interrupt 9 */
+#define UIC_EIR10 0x00000400 /* External interrupt 10 */
+#define UIC_EIR11 0x00000200 /* External interrupt 11 */
+#define UIC_EIR12 0x00000100 /* External interrupt 12 */
+#define UIC_SRE 0x00000080 /* Serial ROM error */
+#define UIC_RSVD2 0x00000040 /* Reserved */
+#define UIC_RSVD3 0x00000020 /* Reserved */
+#define UIC_PAE 0x00000010 /* PCI asynchronous error */
+#define UIC_ETH0 0x00000008 /* Ethernet 0 */
+#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */
+#define UIC_ETH1 0x00000002 /* Ethernet 1 */
+#define UIC_EWU1 0x00000001 /* Ethernet 1 wakeup */
+#elif !defined(CONFIG_440SPE)
#define UIC_MS 0x80000000 /* MAL SERR */
#define UIC_MTDE 0x40000000 /* MAL TXDE */
#define UIC_MRDE 0x20000000 /* MAL RXDE */
@@ -890,6 +1624,117 @@
#define UICB0_ALL (UICB0_UIC0CI | UICB0_UIC0NCI | UICB0_UIC1CI | \
UICB0_UIC1NCI | UICB0_UIC2CI | UICB0_UIC2NCI)
#endif /* CONFIG_440GX */
+/*---------------------------------------------------------------------------+
+| Universal interrupt controller interrupts
++---------------------------------------------------------------------------*/
+#if defined(CONFIG_440SPE)
+/*#define UICB0_UIC0CI 0x80000000*/ /* UIC0 Critical Interrupt */
+/*#define UICB0_UIC0NCI 0x40000000*/ /* UIC0 Noncritical Interrupt */
+#define UICB0_UIC1CI 0x00000002 /* UIC1 Critical Interrupt */
+#define UICB0_UIC1NCI 0x00000001 /* UIC1 Noncritical Interrupt */
+#define UICB0_UIC2CI 0x00200000 /* UIC2 Critical Interrupt */
+#define UICB0_UIC2NCI 0x00100000 /* UIC2 Noncritical Interrupt */
+#define UICB0_UIC3CI 0x00008000 /* UIC3 Critical Interrupt */
+#define UICB0_UIC3NCI 0x00004000 /* UIC3 Noncritical Interrupt */
+
+#define UICB0_ALL (UICB0_UIC1CI | UICB0_UIC1NCI | UICB0_UIC2CI | \
+ UICB0_UIC2NCI | UICB0_UIC3CI | UICB0_UIC3NCI)
+/*---------------------------------------------------------------------------+
+| Universal interrupt controller 0 interrupts (UIC0)
++---------------------------------------------------------------------------*/
+#define UIC_U0 0x80000000 /* UART 0 */
+#define UIC_U1 0x40000000 /* UART 1 */
+#define UIC_IIC0 0x20000000 /* IIC */
+#define UIC_IIC1 0x10000000 /* IIC */
+#define UIC_PIM 0x08000000 /* PCI inbound message */
+#define UIC_PCRW 0x04000000 /* PCI command register write */
+#define UIC_PPM 0x02000000 /* PCI power management */
+#define UIC_PVPDA 0x01000000 /* PCIx 0 vpd access */
+#define UIC_MSI0 0x00800000 /* PCIx MSI level 0 */
+#define UIC_EIR15 0x00400000 /* External intp 15 */
+#define UIC_PEMSI0 0x00080000 /* PCIe MSI level 0 */
+#define UIC_PEMSI1 0x00040000 /* PCIe MSI level 1 */
+#define UIC_PEMSI2 0x00020000 /* PCIe MSI level 2 */
+#define UIC_PEMSI3 0x00010000 /* PCIe MSI level 3 */
+#define UIC_EIR14 0x00002000 /* External interrupt 14 */
+#define UIC_D0CPFF 0x00001000 /* DMA0 cp fifo full */
+#define UIC_D0CSNS 0x00000800 /* DMA0 cs fifo needs service */
+#define UIC_D1CPFF 0x00000400 /* DMA1 cp fifo full */
+#define UIC_D1CSNS 0x00000200 /* DMA1 cs fifo needs service */
+#define UIC_I2OID 0x00000100 /* I2O inbound door bell */
+#define UIC_I2OLNE 0x00000080 /* I2O Inbound Post List FIFO Not Empty */
+#define UIC_I20R0LL 0x00000040 /* I2O Region 0 Low Latency PLB Write */
+#define UIC_I2OR1LL 0x00000020 /* I2O Region 1 Low Latency PLB Write */
+#define UIC_I20R0HB 0x00000010 /* I2O Region 0 High Bandwidth PLB Write */
+#define UIC_I2OR1HB 0x00000008 /* I2O Region 1 High Bandwidth PLB Write */
+#define UIC_CPTCNT 0x00000004 /* GPT Count Timer */
+/*---------------------------------------------------------------------------+
+| Universal interrupt controller 1 interrupts (UIC1)
++---------------------------------------------------------------------------*/
+#define UIC_EIR13 0x80000000 /* externei intp 13 */
+#define UIC_MS 0x40000000 /* MAL SERR */
+#define UIC_MTDE 0x20000000 /* MAL TXDE */
+#define UIC_MRDE 0x10000000 /* MAL RXDE */
+#define UIC_DEUE 0x08000000 /* DDR SDRAM ECC correct/uncorrectable error */
+#define UIC_EBCO 0x04000000 /* EBCO interrupt status */
+#define UIC_MTE 0x02000000 /* MAL TXEOB */
+#define UIC_MRE 0x01000000 /* MAL RXEOB */
+#define UIC_MSI1 0x00800000 /* PCI MSI level 1 */
+#define UIC_MSI2 0x00400000 /* PCI MSI level 2 */
+#define UIC_MSI3 0x00200000 /* PCI MSI level 3 */
+#define UIC_L2C 0x00100000 /* L2 cache */
+#define UIC_CT0 0x00080000 /* GPT compare timer 0 */
+#define UIC_CT1 0x00040000 /* GPT compare timer 1 */
+#define UIC_CT2 0x00020000 /* GPT compare timer 2 */
+#define UIC_CT3 0x00010000 /* GPT compare timer 3 */
+#define UIC_CT4 0x00008000 /* GPT compare timer 4 */
+#define UIC_EIR12 0x00004000 /* External interrupt 12 */
+#define UIC_EIR11 0x00002000 /* External interrupt 11 */
+#define UIC_EIR10 0x00001000 /* External interrupt 10 */
+#define UIC_EIR9 0x00000800 /* External interrupt 9 */
+#define UIC_EIR8 0x00000400 /* External interrupt 8 */
+#define UIC_DMAE 0x00000200 /* dma error */
+#define UIC_I2OE 0x00000100 /* i2o error */
+#define UIC_SRE 0x00000080 /* Serial ROM error */
+#define UIC_PCIXAE 0x00000040 /* Pcix0 async error */
+#define UIC_EIR7 0x00000020 /* External interrupt 7 */
+#define UIC_EIR6 0x00000010 /* External interrupt 6 */
+#define UIC_ETH0 0x00000008 /* Ethernet 0 */
+#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */
+#define UIC_ETH1 0x00000002 /* reserved */
+#define UIC_XOR 0x00000001 /* xor */
+
+/*---------------------------------------------------------------------------+
+| Universal interrupt controller 2 interrupts (UIC2)
++---------------------------------------------------------------------------*/
+#define UIC_PEOAL 0x80000000 /* PE0 AL */
+#define UIC_PEOVA 0x40000000 /* PE0 VPD access */
+#define UIC_PEOHRR 0x20000000 /* PE0 Host reset request rising */
+#define UIC_PE0HRF 0x10000000 /* PE0 Host reset request falling */
+#define UIC_PE0TCR 0x08000000 /* PE0 TCR */
+#define UIC_PE0BVCO 0x04000000 /* PE0 Busmaster VCO */
+#define UIC_PE0DCRE 0x02000000 /* PE0 DCR error */
+#define UIC_PE1AL 0x00800000 /* PE1 AL */
+#define UIC_PE1VA 0x00400000 /* PE1 VPD access */
+#define UIC_PE1HRR 0x00200000 /* PE1 Host reset request rising */
+#define UIC_PE1HRF 0x00100000 /* PE1 Host reset request falling */
+#define UIC_PE1TCR 0x00080000 /* PE1 TCR */
+#define UIC_PE1BVCO 0x00040000 /* PE1 Busmaster VCO */
+#define UIC_PE1DCRE 0x00020000 /* PE1 DCR error */
+#define UIC_PE2AL 0x00008000 /* PE2 AL */
+#define UIC_PE2VA 0x00004000 /* PE2 VPD access */
+#define UIC_PE2HRR 0x00002000 /* PE2 Host reset request rising */
+#define UIC_PE2HRF 0x00001000 /* PE2 Host reset request falling */
+#define UIC_PE2TCR 0x00000800 /* PE2 TCR */
+#define UIC_PE2BVCO 0x00000400 /* PE2 Busmaster VCO */
+#define UIC_PE2DCRE 0x00000200 /* PE2 DCR error */
+#define UIC_EIR5 0x00000080 /* External interrupt 5 */
+#define UIC_EIR4 0x00000040 /* External interrupt 4 */
+#define UIC_EIR3 0x00000020 /* External interrupt 3 */
+#define UIC_EIR2 0x00000010 /* External interrupt 2 */
+#define UIC_EIR1 0x00000008 /* External interrupt 1 */
+#define UIC_EIR0 0x00000004 /* External interrupt 0 */
+#endif /* CONFIG_440SPE */
/*-----------------------------------------------------------------------------+
| External Bus Controller Bit Settings
@@ -981,6 +1826,432 @@
/*-----------------------------------------------------------------------------+
| SDR0 Bit Settings
+-----------------------------------------------------------------------------*/
+#if defined(CONFIG_440SPE)
+#define SDR0_CP440 0x0180
+#define SDR0_CP440_ERPN_MASK 0x30000000
+#define SDR0_CP440_ERPN_MASK_HI 0x3000
+#define SDR0_CP440_ERPN_MASK_LO 0x0000
+#define SDR0_CP440_ERPN_EBC 0x10000000
+#define SDR0_CP440_ERPN_EBC_HI 0x1000
+#define SDR0_CP440_ERPN_EBC_LO 0x0000
+#define SDR0_CP440_ERPN_PCI 0x20000000
+#define SDR0_CP440_ERPN_PCI_HI 0x2000
+#define SDR0_CP440_ERPN_PCI_LO 0x0000
+#define SDR0_CP440_ERPN_ENCODE(n) ((((unsigned long)(n))&0x03)<<28)
+#define SDR0_CP440_ERPN_DECODE(n) ((((unsigned long)(n))>>28)&0x03)
+#define SDR0_CP440_NTO1_MASK 0x00000002
+#define SDR0_CP440_NTO1_NTOP 0x00000000
+#define SDR0_CP440_NTO1_NTO1 0x00000002
+#define SDR0_CP440_NTO1_ENCODE(n) ((((unsigned long)(n))&0x01)<<1)
+#define SDR0_CP440_NTO1_DECODE(n) ((((unsigned long)(n))>>1)&0x01)
+#define SDR0_CFGADDR 0x00E /*already defined line 277 */
+#define SDR0_CFGDATA 0x00F
+
+
+#define SDR0_SDSTP0 0x0020
+#define SDR0_SDSTP0_ENG_MASK 0x80000000
+#define SDR0_SDSTP0_ENG_PLLDIS 0x00000000
+#define SDR0_SDSTP0_ENG_PLLENAB 0x80000000
+#define SDR0_SDSTP0_ENG_ENCODE(n) ((((unsigned long)(n))&0x01)<<31)
+#define SDR0_SDSTP0_ENG_DECODE(n) ((((unsigned long)(n))>>31)&0x01)
+#define SDR0_SDSTP0_SRC_MASK 0x40000000
+#define SDR0_SDSTP0_SRC_PLLOUTA 0x00000000
+#define SDR0_SDSTP0_SRC_PLLOUTB 0x40000000
+#define SDR0_SDSTP0_SRC_ENCODE(n) ((((unsigned long)(n))&0x01)<<30)
+#define SDR0_SDSTP0_SRC_DECODE(n) ((((unsigned long)(n))>>30)&0x01)
+#define SDR0_SDSTP0_SEL_MASK 0x38000000
+#define SDR0_SDSTP0_SEL_PLLOUT 0x00000000
+#define SDR0_SDSTP0_SEL_CPU 0x08000000
+#define SDR0_SDSTP0_SEL_EBC 0x28000000
+#define SDR0_SDSTP0_SEL_ENCODE(n) ((((unsigned long)(n))&0x07)<<27)
+#define SDR0_SDSTP0_SEL_DECODE(n) ((((unsigned long)(n))>>27)&0x07)
+#define SDR0_SDSTP0_TUNE_MASK 0x07FE0000
+#define SDR0_SDSTP0_TUNE_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<17)
+#define SDR0_SDSTP0_TUNE_DECODE(n) ((((unsigned long)(n))>>17)&0x3FF)
+#define SDR0_SDSTP0_FBDV_MASK 0x0001F000
+#define SDR0_SDSTP0_FBDV_ENCODE(n) ((((unsigned long)(n))&0x1F)<<12)
+#define SDR0_SDSTP0_FBDV_DECODE(n) ((((((unsigned long)(n))>>12)-1)&0x1F)+1)
+#define SDR0_SDSTP0_FWDVA_MASK 0x00000F00
+#define SDR0_SDSTP0_FWDVA_ENCODE(n) ((((unsigned long)(n))&0x0F)<<8)
+#define SDR0_SDSTP0_FWDVA_DECODE(n) ((((((unsigned long)(n))>>8)-1)&0x0F)+1)
+#define SDR0_SDSTP0_FWDVB_MASK 0x000000E0
+#define SDR0_SDSTP0_FWDVB_ENCODE(n) ((((unsigned long)(n))&0x07)<<5)
+#define SDR0_SDSTP0_FWDVB_DECODE(n) ((((((unsigned long)(n))>>5)-1)&0x07)+1)
+#define SDR0_SDSTP0_PRBDV0_MASK 0x0000001C
+#define SDR0_SDSTP0_PRBDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<2)
+#define SDR0_SDSTP0_PRBDV0_DECODE(n) ((((((unsigned long)(n))>>2)-1)&0x07)+1)
+#define SDR0_SDSTP0_OPBDV0_MASK 0x00000003
+#define SDR0_SDSTP0_OPBDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<0)
+#define SDR0_SDSTP0_OPBDV0_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0x03)+1)
+
+
+#define SDR0_SDSTP1 0x0021
+#define SDR0_SDSTP1_LFBDV_MASK 0xFC000000
+#define SDR0_SDSTP1_LFBDV_ENCODE(n) ((((unsigned long)(n))&0x3F)<<26)
+#define SDR0_SDSTP1_LFBDV_DECODE(n) ((((unsigned long)(n))>>26)&0x3F)
+#define SDR0_SDSTP1_PERDV0_MASK 0x03000000
+#define SDR0_SDSTP1_PERDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24)
+#define SDR0_SDSTP1_PERDV0_DECODE(n) ((((unsigned long)(n))>>24)&0x03)
+#define SDR0_SDSTP1_MALDV0_MASK 0x00C00000
+#define SDR0_SDSTP1_MALDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<22)
+#define SDR0_SDSTP1_MALDV0_DECODE(n) ((((unsigned long)(n))>>22)&0x03)
+#define SDR0_SDSTP1_DDR_MODE_MASK 0x00300000
+#define SDR0_SDSTP1_DDR1_MODE 0x00100000
+#define SDR0_SDSTP1_DDR2_MODE 0x00200000
+#define SDR0_SDSTP1_DDR_ENCODE(n) ((((unsigned long)(n))&0x03)<<20)
+#define SDR0_SDSTP1_DDR_DECODE(n) ((((unsigned long)(n))>>20)&0x03)
+#define SDR0_SDSTP1_ERPN_MASK 0x00080000
+#define SDR0_SDSTP1_ERPN_EBC 0x00000000
+#define SDR0_SDSTP1_ERPN_PCI 0x00080000
+#define SDR0_SDSTP1_PAE_MASK 0x00040000
+#define SDR0_SDSTP1_PAE_DISABLE 0x00000000
+#define SDR0_SDSTP1_PAE_ENABLE 0x00040000
+#define SDR0_SDSTP1_PAE_ENCODE(n) ((((unsigned long)(n))&0x01)<<18)
+#define SDR0_SDSTP1_PAE_DECODE(n) ((((unsigned long)(n))>>18)&0x01)
+#define SDR0_SDSTP1_PHCE_MASK 0x00020000
+#define SDR0_SDSTP1_PHCE_DISABLE 0x00000000
+#define SDR0_SDSTP1_PHCE_ENABLE 0x00020000
+#define SDR0_SDSTP1_PHCE_ENCODE(n) ((((unsigned long)(n))&0x01)<<17)
+#define SDR0_SDSTP1_PHCE_DECODE(n) ((((unsigned long)(n))>>17)&0x01)
+#define SDR0_SDSTP1_PISE_MASK 0x00010000
+#define SDR0_SDSTP1_PISE_DISABLE 0x00000000
+#define SDR0_SDSTP1_PISE_ENABLE 0x00001000
+#define SDR0_SDSTP1_PISE_ENCODE(n) ((((unsigned long)(n))&0x01)<<16)
+#define SDR0_SDSTP1_PISE_DECODE(n) ((((unsigned long)(n))>>16)&0x01)
+#define SDR0_SDSTP1_PCWE_MASK 0x00008000
+#define SDR0_SDSTP1_PCWE_DISABLE 0x00000000
+#define SDR0_SDSTP1_PCWE_ENABLE 0x00008000
+#define SDR0_SDSTP1_PCWE_ENCODE(n) ((((unsigned long)(n))&0x01)<<15)
+#define SDR0_SDSTP1_PCWE_DECODE(n) ((((unsigned long)(n))>>15)&0x01)
+#define SDR0_SDSTP1_PPIM_MASK 0x00007800
+#define SDR0_SDSTP1_PPIM_ENCODE(n) ((((unsigned long)(n))&0x0F)<<11)
+#define SDR0_SDSTP1_PPIM_DECODE(n) ((((unsigned long)(n))>>11)&0x0F)
+#define SDR0_SDSTP1_PR64E_MASK 0x00000400
+#define SDR0_SDSTP1_PR64E_DISABLE 0x00000000
+#define SDR0_SDSTP1_PR64E_ENABLE 0x00000400
+#define SDR0_SDSTP1_PR64E_ENCODE(n) ((((unsigned long)(n))&0x01)<<10)
+#define SDR0_SDSTP1_PR64E_DECODE(n) ((((unsigned long)(n))>>10)&0x01)
+#define SDR0_SDSTP1_PXFS_MASK 0x00000300
+#define SDR0_SDSTP1_PXFS_100_133 0x00000000
+#define SDR0_SDSTP1_PXFS_66_100 0x00000100
+#define SDR0_SDSTP1_PXFS_50_66 0x00000200
+#define SDR0_SDSTP1_PXFS_0_50 0x00000300
+#define SDR0_SDSTP1_PXFS_ENCODE(n) ((((unsigned long)(n))&0x03)<<8)
+#define SDR0_SDSTP1_PXFS_DECODE(n) ((((unsigned long)(n))>>8)&0x03)
+#define SDR0_SDSTP1_EBCW_MASK 0x00000080 /* SOP */
+#define SDR0_SDSTP1_EBCW_8_BITS 0x00000000 /* SOP */
+#define SDR0_SDSTP1_EBCW_16_BITS 0x00000080 /* SOP */
+#define SDR0_SDSTP1_DBGEN_MASK 0x00000030 /* $218C */
+#define SDR0_SDSTP1_DBGEN_FUNC 0x00000000
+#define SDR0_SDSTP1_DBGEN_TRACE 0x00000010
+#define SDR0_SDSTP1_DBGEN_ENCODE(n) ((((unsigned long)(n))&0x03)<<4) /* $218C */
+#define SDR0_SDSTP1_DBGEN_DECODE(n) ((((unsigned long)(n))>>4)&0x03) /* $218C */
+#define SDR0_SDSTP1_ETH_MASK 0x00000004
+#define SDR0_SDSTP1_ETH_10_100 0x00000000
+#define SDR0_SDSTP1_ETH_GIGA 0x00000004
+#define SDR0_SDSTP1_ETH_ENCODE(n) ((((unsigned long)(n))&0x01)<<2)
+#define SDR0_SDSTP1_ETH_DECODE(n) ((((unsigned long)(n))>>2)&0x01)
+#define SDR0_SDSTP1_NTO1_MASK 0x00000001
+#define SDR0_SDSTP1_NTO1_DISABLE 0x00000000
+#define SDR0_SDSTP1_NTO1_ENABLE 0x00000001
+#define SDR0_SDSTP1_NTO1_ENCODE(n) ((((unsigned long)(n))&0x01)<<0)
+#define SDR0_SDSTP1_NTO1_DECODE(n) ((((unsigned long)(n))>>0)&0x01)
+
+#define SDR0_SDSTP2 0x0022
+#define SDR0_SDSTP2_P1AE_MASK 0x80000000
+#define SDR0_SDSTP2_P1AE_DISABLE 0x00000000
+#define SDR0_SDSTP2_P1AE_ENABLE 0x80000000
+#define SDR0_SDSTP2_P1AE_ENCODE(n) ((((unsigned long)(n))&0x01)<<31)
+#define SDR0_SDSTP2_P1AE_DECODE(n) ((((unsigned long)(n))>>31)&0x01)
+#define SDR0_SDSTP2_P1HCE_MASK 0x40000000
+#define SDR0_SDSTP2_P1HCE_DISABLE 0x00000000
+#define SDR0_SDSTP2_P1HCE_ENABLE 0x40000000
+#define SDR0_SDSTP2_P1HCE_ENCODE(n) ((((unsigned long)(n))&0x01)<<30)
+#define SDR0_SDSTP2_P1HCE_DECODE(n) ((((unsigned long)(n))>>30)&0x01)
+#define SDR0_SDSTP2_P1ISE_MASK 0x20000000
+#define SDR0_SDSTP2_P1ISE_DISABLE 0x00000000
+#define SDR0_SDSTP2_P1ISE_ENABLE 0x20000000
+#define SDR0_SDSTP2_P1ISE_ENCODE(n) ((((unsigned long)(n))&0x01)<<29)
+#define SDR0_SDSTP2_P1ISE_DECODE(n) ((((unsigned long)(n))>>29)&0x01)
+#define SDR0_SDSTP2_P1CWE_MASK 0x10000000
+#define SDR0_SDSTP2_P1CWE_DISABLE 0x00000000
+#define SDR0_SDSTP2_P1CWE_ENABLE 0x10000000
+#define SDR0_SDSTP2_P1CWE_ENCODE(n) ((((unsigned long)(n))&0x01)<<28)
+#define SDR0_SDSTP2_P1CWE_DECODE(n) ((((unsigned long)(n))>>28)&0x01)
+#define SDR0_SDSTP2_P1PIM_MASK 0x0F000000
+#define SDR0_SDSTP2_P1PIM_ENCODE(n) ((((unsigned long)(n))&0x0F)<<24)
+#define SDR0_SDSTP2_P1PIM_DECODE(n) ((((unsigned long)(n))>>24)&0x0F)
+#define SDR0_SDSTP2_P1R64E_MASK 0x00800000
+#define SDR0_SDSTP2_P1R64E_DISABLE 0x00000000
+#define SDR0_SDSTP2_P1R64E_ENABLE 0x00800000
+#define SDR0_SDSTP2_P1R64E_ENCODE(n) ((((unsigned long)(n))&0x01)<<23)
+#define SDR0_SDSTP2_P1R64E_DECODE(n) ((((unsigned long)(n))>>23)&0x01)
+#define SDR0_SDSTP2_P1XFS_MASK 0x00600000
+#define SDR0_SDSTP2_P1XFS_100_133 0x00000000
+#define SDR0_SDSTP2_P1XFS_66_100 0x00200000
+#define SDR0_SDSTP2_P1XFS_50_66 0x00400000
+#define SDR0_SDSTP2_P1XFS_0_50 0x00600000
+#define SDR0_SDSTP2_P1XFS_ENCODE(n) ((((unsigned long)(n))&0x03)<<21)
+#define SDR0_SDSTP2_P1XFS_DECODE(n) ((((unsigned long)(n))>>21)&0x03)
+#define SDR0_SDSTP2_P2AE_MASK 0x00040000
+#define SDR0_SDSTP2_P2AE_DISABLE 0x00000000
+#define SDR0_SDSTP2_P2AE_ENABLE 0x00040000
+#define SDR0_SDSTP2_P2AE_ENCODE(n) ((((unsigned long)(n))&0x01)<<18)
+#define SDR0_SDSTP2_P2AE_DECODE(n) ((((unsigned long)(n))>>18)&0x01)
+#define SDR0_SDSTP2_P2HCE_MASK 0x00020000
+#define SDR0_SDSTP2_P2HCE_DISABLE 0x00000000
+#define SDR0_SDSTP2_P2HCE_ENABLE 0x00020000
+#define SDR0_SDSTP2_P2HCE_ENCODE(n) ((((unsigned long)(n))&0x01)<<17)
+#define SDR0_SDSTP2_P2HCE_DECODE(n) ((((unsigned long)(n))>>17)&0x01)
+#define SDR0_SDSTP2_P2ISE_MASK 0x00010000
+#define SDR0_SDSTP2_P2ISE_DISABLE 0x00000000
+#define SDR0_SDSTP2_P2ISE_ENABLE 0x00010000
+#define SDR0_SDSTP2_P2ISE_ENCODE(n) ((((unsigned long)(n))&0x01)<<16)
+#define SDR0_SDSTP2_P2ISE_DECODE(n) ((((unsigned long)(n))>>16)&0x01)
+#define SDR0_SDSTP2_P2CWE_MASK 0x00008000
+#define SDR0_SDSTP2_P2CWE_DISABLE 0x00000000
+#define SDR0_SDSTP2_P2CWE_ENABLE 0x00008000
+#define SDR0_SDSTP2_P2CWE_ENCODE(n) ((((unsigned long)(n))&0x01)<<15)
+#define SDR0_SDSTP2_P2CWE_DECODE(n) ((((unsigned long)(n))>>15)&0x01)
+#define SDR0_SDSTP2_P2PIM_MASK 0x00007800
+#define SDR0_SDSTP2_P2PIM_ENCODE(n) ((((unsigned long)(n))&0x0F)<<11)
+#define SDR0_SDSTP2_P2PIM_DECODE(n) ((((unsigned long)(n))>>11)&0x0F)
+#define SDR0_SDSTP2_P2XFS_MASK 0x00000300
+#define SDR0_SDSTP2_P2XFS_100_133 0x00000000
+#define SDR0_SDSTP2_P2XFS_66_100 0x00000100
+#define SDR0_SDSTP2_P2XFS_50_66 0x00000200
+#define SDR0_SDSTP2_P2XFS_0_50 0x00000100
+#define SDR0_SDSTP2_P2XFS_ENCODE(n) ((((unsigned long)(n))&0x03)<<8)
+#define SDR0_SDSTP2_P2XFS_DECODE(n) ((((unsigned long)(n))>>8)&0x03)
+
+#define SDR0_SDSTP3 0x0023
+
+#define SDR0_PINSTP 0x0040
+#define SDR0_PINSTP_BOOTSTRAP_MASK 0xC0000000 /* Strap Bits */
+#define SDR0_PINSTP_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0 (EBC boot) */
+#define SDR0_PINSTP_BOOTSTRAP_SETTINGS1 0x40000000 /* Default strap settings 1 (PCI boot) */
+#define SDR0_PINSTP_BOOTSTRAP_IIC_54_EN 0x80000000 /* Serial Device Enabled - Addr = 0x54 */
+#define SDR0_PINSTP_BOOTSTRAP_IIC_50_EN 0xC0000000 /* Serial Device Enabled - Addr = 0x50 */
+#define SDR0_SDCS 0x0060
+#define SDR0_ECID0 0x0080
+#define SDR0_ECID1 0x0081
+#define SDR0_ECID2 0x0082
+#define SDR0_JTAG 0x00C0
+
+#define SDR0_DDR0 0x00E1
+#define SDR0_DDR0_DPLLRST 0x80000000
+#define SDR0_DDR0_DDRM_MASK 0x60000000
+#define SDR0_DDR0_DDRM_DDR1 0x20000000
+#define SDR0_DDR0_DDRM_DDR2 0x40000000
+#define SDR0_DDR0_DDRM_ENCODE(n) ((((unsigned long)(n))&0x03)<<29)
+#define SDR0_DDR0_DDRM_DECODE(n) ((((unsigned long)(n))>>29)&0x03)
+#define SDR0_DDR0_TUNE_ENCODE(n) ((((unsigned long)(n))&0x2FF)<<0)
+#define SDR0_DDR0_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x2FF)
+
+#define SDR0_UART0 0x0120
+#define SDR0_UART1 0x0121
+#define SDR0_UART2 0x0122
+#define SDR0_UARTX_UXICS_MASK 0xF0000000
+#define SDR0_UARTX_UXICS_PLB 0x20000000
+#define SDR0_UARTX_UXEC_MASK 0x00800000
+#define SDR0_UARTX_UXEC_INT 0x00000000
+#define SDR0_UARTX_UXEC_EXT 0x00800000
+#define SDR0_UARTX_UXDIV_MASK 0x000000FF
+#define SDR0_UARTX_UXDIV_ENCODE(n) ((((unsigned long)(n))&0xFF)<<0)
+#define SDR0_UARTX_UXDIV_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0xFF)+1)
+
+#define SDR0_CP440 0x0180
+#define SDR0_CP440_ERPN_MASK 0x30000000
+#define SDR0_CP440_ERPN_MASK_HI 0x3000
+#define SDR0_CP440_ERPN_MASK_LO 0x0000
+#define SDR0_CP440_ERPN_EBC 0x10000000
+#define SDR0_CP440_ERPN_EBC_HI 0x1000
+#define SDR0_CP440_ERPN_EBC_LO 0x0000
+#define SDR0_CP440_ERPN_PCI 0x20000000
+#define SDR0_CP440_ERPN_PCI_HI 0x2000
+#define SDR0_CP440_ERPN_PCI_LO 0x0000
+#define SDR0_CP440_ERPN_ENCODE(n) ((((unsigned long)(n))&0x03)<<28)
+#define SDR0_CP440_ERPN_DECODE(n) ((((unsigned long)(n))>>28)&0x03)
+#define SDR0_CP440_NTO1_MASK 0x00000002
+#define SDR0_CP440_NTO1_NTOP 0x00000000
+#define SDR0_CP440_NTO1_NTO1 0x00000002
+#define SDR0_CP440_NTO1_ENCODE(n) ((((unsigned long)(n))&0x01)<<1)
+#define SDR0_CP440_NTO1_DECODE(n) ((((unsigned long)(n))>>1)&0x01)
+
+#define SDR0_XCR0 0x01C0
+#define SDR0_XCR1 0x01C3
+#define SDR0_XCR2 0x01C6
+#define SDR0_XCRn_PAE_MASK 0x80000000
+#define SDR0_XCRn_PAE_DISABLE 0x00000000
+#define SDR0_XCRn_PAE_ENABLE 0x80000000
+#define SDR0_XCRn_PAE_ENCODE(n) ((((unsigned long)(n))&0x01)<<31)
+#define SDR0_XCRn_PAE_DECODE(n) ((((unsigned long)(n))>>31)&0x01)
+#define SDR0_XCRn_PHCE_MASK 0x40000000
+#define SDR0_XCRn_PHCE_DISABLE 0x00000000
+#define SDR0_XCRn_PHCE_ENABLE 0x40000000
+#define SDR0_XCRn_PHCE_ENCODE(n) ((((unsigned long)(n))&0x01)<<30)
+#define SDR0_XCRn_PHCE_DECODE(n) ((((unsigned long)(n))>>30)&0x01)
+#define SDR0_XCRn_PISE_MASK 0x20000000
+#define SDR0_XCRn_PISE_DISABLE 0x00000000
+#define SDR0_XCRn_PISE_ENABLE 0x20000000
+#define SDR0_XCRn_PISE_ENCODE(n) ((((unsigned long)(n))&0x01)<<29)
+#define SDR0_XCRn_PISE_DECODE(n) ((((unsigned long)(n))>>29)&0x01)
+#define SDR0_XCRn_PCWE_MASK 0x10000000
+#define SDR0_XCRn_PCWE_DISABLE 0x00000000
+#define SDR0_XCRn_PCWE_ENABLE 0x10000000
+#define SDR0_XCRn_PCWE_ENCODE(n) ((((unsigned long)(n))&0x01)<<28)
+#define SDR0_XCRn_PCWE_DECODE(n) ((((unsigned long)(n))>>28)&0x01)
+#define SDR0_XCRn_PPIM_MASK 0x0F000000
+#define SDR0_XCRn_PPIM_ENCODE(n) ((((unsigned long)(n))&0x0F)<<24)
+#define SDR0_XCRn_PPIM_DECODE(n) ((((unsigned long)(n))>>24)&0x0F)
+#define SDR0_XCRn_PR64E_MASK 0x00800000
+#define SDR0_XCRn_PR64E_DISABLE 0x00000000
+#define SDR0_XCRn_PR64E_ENABLE 0x00800000
+#define SDR0_XCRn_PR64E_ENCODE(n) ((((unsigned long)(n))&0x01)<<23)
+#define SDR0_XCRn_PR64E_DECODE(n) ((((unsigned long)(n))>>23)&0x01)
+#define SDR0_XCRn_PXFS_MASK 0x00600000
+#define SDR0_XCRn_PXFS_100_133 0x00000000
+#define SDR0_XCRn_PXFS_66_100 0x00200000
+#define SDR0_XCRn_PXFS_50_66 0x00400000
+#define SDR0_XCRn_PXFS_0_33 0x00600000
+#define SDR0_XCRn_PXFS_ENCODE(n) ((((unsigned long)(n))&0x03)<<21)
+#define SDR0_XCRn_PXFS_DECODE(n) ((((unsigned long)(n))>>21)&0x03)
+
+#define SDR0_XPLLC0 0x01C1
+#define SDR0_XPLLD0 0x01C2
+#define SDR0_XPLLC1 0x01C4
+#define SDR0_XPLLD1 0x01C5
+#define SDR0_XPLLC2 0x01C7
+#define SDR0_XPLLD2 0x01C8
+#define SDR0_SRST 0x0200
+#define SDR0_SLPIPE 0x0220
+
+#define SDR0_AMP0 0x0240
+#define SDR0_AMP0_PRIORITY 0xFFFF0000
+#define SDR0_AMP0_ALTERNATE_PRIORITY 0x0000FF00
+#define SDR0_AMP0_RESERVED_BITS_MASK 0x000000FF
+
+#define SDR0_AMP1 0x0241
+#define SDR0_AMP1_PRIORITY 0xFC000000
+#define SDR0_AMP1_ALTERNATE_PRIORITY 0x0000E000
+#define SDR0_AMP1_RESERVED_BITS_MASK 0x03FF1FFF
+
+#define SDR0_MIRQ0 0x0260
+#define SDR0_MIRQ1 0x0261
+#define SDR0_MALTBL 0x0280
+#define SDR0_MALRBL 0x02A0
+#define SDR0_MALTBS 0x02C0
+#define SDR0_MALRBS 0x02E0
+
+/* Reserved for Customer Use */
+#define SDR0_CUST0 0x4000
+#define SDR0_CUST0_AUTONEG_MASK 0x8000000
+#define SDR0_CUST0_NO_AUTONEG 0x0000000
+#define SDR0_CUST0_AUTONEG 0x8000000
+#define SDR0_CUST0_ETH_FORCE_MASK 0x6000000
+#define SDR0_CUST0_ETH_FORCE_10MHZ 0x0000000
+#define SDR0_CUST0_ETH_FORCE_100MHZ 0x2000000
+#define SDR0_CUST0_ETH_FORCE_1000MHZ 0x4000000
+#define SDR0_CUST0_ETH_DUPLEX_MASK 0x1000000
+#define SDR0_CUST0_ETH_HALF_DUPLEX 0x0000000
+#define SDR0_CUST0_ETH_FULL_DUPLEX 0x1000000
+
+#define SDR0_SDSTP4 0x4001
+#define SDR0_CUST1 0x4002
+#define SDR0_SDSTP5 0x4003
+#define SDR0_CUST2 0x4004
+#define SDR0_SDSTP6 0x4005
+#define SDR0_CUST3 0x4006
+#define SDR0_SDSTP7 0x4007
+
+#define SDR0_PFC0 0x4100
+#define SDR0_PFC0_GPIO_0 0x80000000
+#define SDR0_PFC0_PCIX0REQ2_N 0x00000000
+#define SDR0_PFC0_GPIO_1 0x40000000
+#define SDR0_PFC0_PCIX0REQ3_N 0x00000000
+#define SDR0_PFC0_GPIO_2 0x20000000
+#define SDR0_PFC0_PCIX0GNT2_N 0x00000000
+#define SDR0_PFC0_GPIO_3 0x10000000
+#define SDR0_PFC0_PCIX0GNT3_N 0x00000000
+#define SDR0_PFC0_GPIO_4 0x08000000
+#define SDR0_PFC0_PCIX1REQ2_N 0x00000000
+#define SDR0_PFC0_GPIO_5 0x04000000
+#define SDR0_PFC0_PCIX1REQ3_N 0x00000000
+#define SDR0_PFC0_GPIO_6 0x02000000
+#define SDR0_PFC0_PCIX1GNT2_N 0x00000000
+#define SDR0_PFC0_GPIO_7 0x01000000
+#define SDR0_PFC0_PCIX1GNT3_N 0x00000000
+#define SDR0_PFC0_GPIO_8 0x00800000
+#define SDR0_PFC0_PERREADY 0x00000000
+#define SDR0_PFC0_GPIO_9 0x00400000
+#define SDR0_PFC0_PERCS1_N 0x00000000
+#define SDR0_PFC0_GPIO_10 0x00200000
+#define SDR0_PFC0_PERCS2_N 0x00000000
+#define SDR0_PFC0_GPIO_11 0x00100000
+#define SDR0_PFC0_IRQ0 0x00000000
+#define SDR0_PFC0_GPIO_12 0x00080000
+#define SDR0_PFC0_IRQ1 0x00000000
+#define SDR0_PFC0_GPIO_13 0x00040000
+#define SDR0_PFC0_IRQ2 0x00000000
+#define SDR0_PFC0_GPIO_14 0x00020000
+#define SDR0_PFC0_IRQ3 0x00000000
+#define SDR0_PFC0_GPIO_15 0x00010000
+#define SDR0_PFC0_IRQ4 0x00000000
+#define SDR0_PFC0_GPIO_16 0x00008000
+#define SDR0_PFC0_IRQ5 0x00000000
+#define SDR0_PFC0_GPIO_17 0x00004000
+#define SDR0_PFC0_PERBE0_N 0x00000000
+#define SDR0_PFC0_GPIO_18 0x00002000
+#define SDR0_PFC0_PCI0GNT0_N 0x00000000
+#define SDR0_PFC0_GPIO_19 0x00001000
+#define SDR0_PFC0_PCI0GNT1_N 0x00000000
+#define SDR0_PFC0_GPIO_20 0x00000800
+#define SDR0_PFC0_PCI0REQ0_N 0x00000000
+#define SDR0_PFC0_GPIO_21 0x00000400
+#define SDR0_PFC0_PCI0REQ1_N 0x00000000
+#define SDR0_PFC0_GPIO_22 0x00000200
+#define SDR0_PFC0_PCI1GNT0_N 0x00000000
+#define SDR0_PFC0_GPIO_23 0x00000100
+#define SDR0_PFC0_PCI1GNT1_N 0x00000000
+#define SDR0_PFC0_GPIO_24 0x00000080
+#define SDR0_PFC0_PCI1REQ0_N 0x00000000
+#define SDR0_PFC0_GPIO_25 0x00000040
+#define SDR0_PFC0_PCI1REQ1_N 0x00000000
+#define SDR0_PFC0_GPIO_26 0x00000020
+#define SDR0_PFC0_PCI2GNT0_N 0x00000000
+#define SDR0_PFC0_GPIO_27 0x00000010
+#define SDR0_PFC0_PCI2GNT1_N 0x00000000
+#define SDR0_PFC0_GPIO_28 0x00000008
+#define SDR0_PFC0_PCI2REQ0_N 0x00000000
+#define SDR0_PFC0_GPIO_29 0x00000004
+#define SDR0_PFC0_PCI2REQ1_N 0x00000000
+#define SDR0_PFC0_GPIO_30 0x00000002
+#define SDR0_PFC0_UART1RX 0x00000000
+#define SDR0_PFC0_GPIO_31 0x00000001
+#define SDR0_PFC0_UART1TX 0x00000000
+
+#define SDR0_PFC1 0x4101
+#define SDR0_PFC1_UART1_CTS_RTS_MASK 0x02000000
+#define SDR0_PFC1_UART1_DSR_DTR 0x00000000
+#define SDR0_PFC1_UART1_CTS_RTS 0x02000000
+#define SDR0_PFC1_UART2_IN_SERVICE_MASK 0x01000000
+#define SDR0_PFC1_UART2_NOT_IN_SERVICE 0x00000000
+#define SDR0_PFC1_UART2_IN_SERVICE 0x01000000
+#define SDR0_PFC1_ETH_GIGA_MASK 0x00200000
+#define SDR0_PFC1_ETH_10_100 0x00000000
+#define SDR0_PFC1_ETH_GIGA 0x00200000
+#define SDR0_PFC1_ETH_GIGA_ENCODE(n) ((((unsigned long)(n))&0x1)<<21)
+#define SDR0_PFC1_ETH_GIGA_DECODE(n) ((((unsigned long)(n))>>21)&0x01)
+#define SDR0_PFC1_CPU_TRACE_MASK 0x00180000 /* $218C */
+#define SDR0_PFC1_CPU_NO_TRACE 0x00000000
+#define SDR0_PFC1_CPU_TRACE 0x00080000
+#define SDR0_PFC1_CPU_TRACE_ENCODE(n) ((((unsigned long)(n))&0x3)<<19) /* $218C */
+#define SDR0_PFC1_CPU_TRACE_DECODE(n) ((((unsigned long)(n))>>19)&0x03) /* $218C */
+
+#define SDR0_MFR 0x4300
+#endif /* CONFIG_440SPE */
+
+
#define SDR0_SDCS_SDD (0x80000000 >> 31)
#if defined(CONFIG_440GP)
@@ -1159,7 +2430,7 @@
/*-----------------------------------------------------------------------------+
| Clocking
+-----------------------------------------------------------------------------*/
-#if !defined (CONFIG_440GX) && !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && !defined(CONFIG_440SP)
+#if !defined (CONFIG_440GX) && !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)
#define PLLSYS0_TUNE_MASK 0xffc00000 /* PLL TUNE bits */
#define PLLSYS0_FB_DIV_MASK 0x003c0000 /* Feedback divisor */
#define PLLSYS0_FWD_DIV_A_MASK 0x00038000 /* Forward divisor A */
@@ -1498,6 +2769,9 @@
unsigned long freqOPB;
unsigned long freqEPB;
unsigned long freqPCI;
+#ifdef CONFIG_440SPE
+ unsigned long freqDDR;
+#endif
unsigned long pciIntArbEn; /* Internal PCI arbiter is enabled */
unsigned long pciClkSync; /* PCI clock is synchronous */
} PPC440_SYS_INFO;
diff --git a/include/ppc4xx_enet.h b/include/ppc4xx_enet.h
index d6d33b6..ec2e362 100644
--- a/include/ppc4xx_enet.h
+++ b/include/ppc4xx_enet.h
@@ -133,12 +133,21 @@
#define EMAC_NUM_DEV 4
#elif (defined(CONFIG_440) || defined(CONFIG_405EP)) && \
defined(CONFIG_NET_MULTI) && \
- !defined(CONFIG_440SP)
+ !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)
#define EMAC_NUM_DEV 2
#else
#define EMAC_NUM_DEV 1
#endif
+#ifdef CONFIG_IBM_EMAC4_V4 /* EMAC4 V4 changed bit setting */
+#define EMAC_STACR_OC_MASK (0x00008000)
+#else
+#define EMAC_STACR_OC_MASK (0x00000000)
+#endif
+
+#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
+#define SDR0_PFC1_EM_1000 (0x00200000)
+#endif
/*ZMII Bridge Register addresses */
#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
@@ -323,7 +332,7 @@
#define EMAC_M0_WKE (0x04000000)
/* on 440GX EMAC_MR1 has a different layout! */
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
/* MODE Reg 1 */
#define EMAC_M1_FDE (0x80000000)
#define EMAC_M1_ILE (0x40000000)
@@ -424,8 +433,21 @@
/* STA CONTROL REG */
#define EMAC_STACR_OC (0x00008000)
#define EMAC_STACR_PHYE (0x00004000)
+
+#ifdef CONFIG_IBM_EMAC4_V4 /* EMAC4 V4 changed bit setting */
+#define EMAC_STACR_INDIRECT_MODE (0x00002000)
+#define EMAC_STACR_WRITE (0x00000800) /* $BUC */
+#define EMAC_STACR_READ (0x00001000) /* $BUC */
+#define EMAC_STACR_OP_MASK (0x00001800)
+#define EMAC_STACR_MDIO_ADDR (0x00000000)
+#define EMAC_STACR_MDIO_WRITE (0x00000800)
+#define EMAC_STACR_MDIO_READ (0x00001800)
+#define EMAC_STACR_MDIO_READ_INC (0x00001000)
+#else
#define EMAC_STACR_WRITE (0x00002000)
#define EMAC_STACR_READ (0x00001000)
+#endif
+
#define EMAC_STACR_CLK_83MHZ (0x00000800) /* 0's for 50Mhz */
#define EMAC_STACR_CLK_66MHZ (0x00000400)
#define EMAC_STACR_CLK_100MHZ (0x00000C00)
diff --git a/include/s3c2400.h b/include/s3c2400.h
index bc1f1e9..4fdc62e 100644
--- a/include/s3c2400.h
+++ b/include/s3c2400.h
@@ -63,71 +63,71 @@
#include <s3c24x0.h>
-static inline S3C24X0_MEMCTL * const S3C24X0_GetBase_MEMCTL(void)
+static inline S3C24X0_MEMCTL * S3C24X0_GetBase_MEMCTL(void)
{
return (S3C24X0_MEMCTL * const)S3C24X0_MEMCTL_BASE;
}
-static inline S3C24X0_USB_HOST * const S3C24X0_GetBase_USB_HOST(void)
+static inline S3C24X0_USB_HOST * S3C24X0_GetBase_USB_HOST(void)
{
return (S3C24X0_USB_HOST * const)S3C24X0_USB_HOST_BASE;
}
-static inline S3C24X0_INTERRUPT * const S3C24X0_GetBase_INTERRUPT(void)
+static inline S3C24X0_INTERRUPT * S3C24X0_GetBase_INTERRUPT(void)
{
return (S3C24X0_INTERRUPT * const)S3C24X0_INTERRUPT_BASE;
}
-static inline S3C24X0_DMAS * const S3C24X0_GetBase_DMAS(void)
+static inline S3C24X0_DMAS * S3C24X0_GetBase_DMAS(void)
{
return (S3C24X0_DMAS * const)S3C24X0_DMA_BASE;
}
-static inline S3C24X0_CLOCK_POWER * const S3C24X0_GetBase_CLOCK_POWER(void)
+static inline S3C24X0_CLOCK_POWER * S3C24X0_GetBase_CLOCK_POWER(void)
{
return (S3C24X0_CLOCK_POWER * const)S3C24X0_CLOCK_POWER_BASE;
}
-static inline S3C24X0_LCD * const S3C24X0_GetBase_LCD(void)
+static inline S3C24X0_LCD * S3C24X0_GetBase_LCD(void)
{
return (S3C24X0_LCD * const)S3C24X0_LCD_BASE;
}
-static inline S3C24X0_UART * const S3C24X0_GetBase_UART(S3C24X0_UARTS_NR nr)
+static inline S3C24X0_UART * S3C24X0_GetBase_UART(S3C24X0_UARTS_NR nr)
{
return (S3C24X0_UART * const)(S3C24X0_UART_BASE + (nr * 0x4000));
}
-static inline S3C24X0_TIMERS * const S3C24X0_GetBase_TIMERS(void)
+static inline S3C24X0_TIMERS * S3C24X0_GetBase_TIMERS(void)
{
return (S3C24X0_TIMERS * const)S3C24X0_TIMER_BASE;
}
-static inline S3C24X0_USB_DEVICE * const S3C24X0_GetBase_USB_DEVICE(void)
+static inline S3C24X0_USB_DEVICE * S3C24X0_GetBase_USB_DEVICE(void)
{
return (S3C24X0_USB_DEVICE * const)S3C24X0_USB_DEVICE_BASE;
}
-static inline S3C24X0_WATCHDOG * const S3C24X0_GetBase_WATCHDOG(void)
+static inline S3C24X0_WATCHDOG * S3C24X0_GetBase_WATCHDOG(void)
{
return (S3C24X0_WATCHDOG * const)S3C24X0_WATCHDOG_BASE;
}
-static inline S3C24X0_I2C * const S3C24X0_GetBase_I2C(void)
+static inline S3C24X0_I2C * S3C24X0_GetBase_I2C(void)
{
return (S3C24X0_I2C * const)S3C24X0_I2C_BASE;
}
-static inline S3C24X0_I2S * const S3C24X0_GetBase_I2S(void)
+static inline S3C24X0_I2S * S3C24X0_GetBase_I2S(void)
{
return (S3C24X0_I2S * const)S3C24X0_I2S_BASE;
}
-static inline S3C24X0_GPIO * const S3C24X0_GetBase_GPIO(void)
+static inline S3C24X0_GPIO * S3C24X0_GetBase_GPIO(void)
{
return (S3C24X0_GPIO * const)S3C24X0_GPIO_BASE;
}
-static inline S3C24X0_RTC * const S3C24X0_GetBase_RTC(void)
+static inline S3C24X0_RTC * S3C24X0_GetBase_RTC(void)
{
return (S3C24X0_RTC * const)S3C24X0_RTC_BASE;
}
-static inline S3C2400_ADC * const S3C2400_GetBase_ADC(void)
+static inline S3C2400_ADC * S3C2400_GetBase_ADC(void)
{
return (S3C2400_ADC * const)S3C24X0_ADC_BASE;
}
-static inline S3C24X0_SPI * const S3C24X0_GetBase_SPI(void)
+static inline S3C24X0_SPI * S3C24X0_GetBase_SPI(void)
{
return (S3C24X0_SPI * const)S3C24X0_SPI_BASE;
}
-static inline S3C2400_MMC * const S3C2400_GetBase_MMC(void)
+static inline S3C2400_MMC * S3C2400_GetBase_MMC(void)
{
return (S3C2400_MMC * const)S3C2400_MMC_BASE;
}
diff --git a/include/usb.h b/include/usb.h
index 39d7f23..bf71554 100644
--- a/include/usb.h
+++ b/include/usb.h
@@ -108,6 +108,7 @@
unsigned char iInterface;
unsigned char no_of_ep;
+ unsigned char num_altsetting;
unsigned char act_altsetting;
struct usb_endpoint_descriptor ep_desc[USB_MAXENDPOINTS];
} __attribute__ ((packed));
diff --git a/include/xyzModem.h b/include/xyzModem.h
index 4ec10b5..f437bbd 100644
--- a/include/xyzModem.h
+++ b/include/xyzModem.h
@@ -97,7 +97,10 @@
#endif
} connection_info_t;
+#ifndef BOOL_WAS_DEFINED
+#define BOOL_WAS_DEFINED
typedef unsigned int bool;
+#endif
#define false 0
#define true 1
diff --git a/lib_i386/i386_linux.c b/lib_i386/i386_linux.c
index e5d8eea..b4a6f5a 100644
--- a/lib_i386/i386_linux.c
+++ b/lib_i386/i386_linux.c
@@ -151,6 +151,12 @@
initrd_end = 0;
}
+ /* if multi-part image, we need to advance base ptr */
+ if ((hdr->ih_type==IH_TYPE_MULTI) && (len_ptr[1])) {
+ int i;
+ for (i=0, addr+=sizeof(int); len_ptr[i++]; addr+=sizeof(int));
+ }
+
base_ptr = load_zimage((void*)addr + sizeof(image_header_t), ntohl(hdr->ih_size),
initrd_start, initrd_end-initrd_start, 0);
diff --git a/lib_ppc/board.c b/lib_ppc/board.c
index e68cf1f..db80f77 100644
--- a/lib_ppc/board.c
+++ b/lib_ppc/board.c
@@ -270,7 +270,8 @@
#if !defined(CONFIG_8xx_CPUCLK_DEFAULT)
get_clocks, /* get CPU and bus clocks (etc.) */
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M)
+#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) \
+ && !defined(CONFIG_TQM885D)
adjust_sdram_tbs_8xx,
#endif
init_timebase,
@@ -610,6 +611,11 @@
bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
+ gd->reloc_off = dest_addr - CFG_MONITOR_BASE;
+
+#ifdef CONFIG_SERIAL_MULTI
+ serial_initialize();
+#endif
debug ("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
@@ -619,14 +625,8 @@
board_early_init_r ();
#endif
- gd->reloc_off = dest_addr - CFG_MONITOR_BASE;
-
monitor_flash_len = (ulong)&__init_end - dest_addr;
-#ifdef CONFIG_SERIAL_MULTI
- serial_initialize();
-#endif
-
/*
* We have to relocate the command table manually
*/
diff --git a/mkconfig b/mkconfig
index 54775d3..4fe6e44 100755
--- a/mkconfig
+++ b/mkconfig
@@ -9,19 +9,23 @@
#
APPEND=no # Default: Create new config file
+BOARD_NAME="" # Name to print in make output
while [ $# -gt 0 ] ; do
case "$1" in
--) shift ; break ;;
-a) shift ; APPEND=yes ;;
+ -n) shift ; BOARD_NAME="${1%%_config}" ; shift ;;
*) break ;;
esac
done
+[ "${BOARD_NAME}" ] || BOARD_NAME="$1"
+
[ $# -lt 4 ] && exit 1
[ $# -gt 6 ] && exit 1
-echo "Configuring for $1 board..."
+echo "Configuring for ${BOARD_NAME} board..."
cd ./include
diff --git a/net/tftp.c b/net/tftp.c
index eca21d2..f3a5471 100644
--- a/net/tftp.c
+++ b/net/tftp.c
@@ -225,7 +225,7 @@
if (TftpBlock == 0) {
TftpBlockWrap++;
TftpBlockWrapOffset += TFTP_BLOCK_SIZE * TFTP_SEQUENCE_SIZE;
- printf ("\n\t %lu MB reveived\n\t ", TftpBlockWrapOffset>>20);
+ printf ("\n\t %lu MB received\n\t ", TftpBlockWrapOffset>>20);
} else {
if (((TftpBlock - 1) % 10) == 0) {
putc ('#');
