ppc4xx: Add AMCC Glacier 406GT eval board support
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c
index d990250..4541a14 100644
--- a/cpu/ppc4xx/4xx_enet.c
+++ b/cpu/ppc4xx/4xx_enet.c
@@ -275,6 +275,7 @@
{
EMAC_4XX_HW_PST hw_p = dev->priv;
uint32_t failsafe = 10000;
+ u32 eth_cfg = 0;
out_be32((void *)EMAC_IER + hw_p->hw_addr, 0x00000000); /* disable emac interrupts */
@@ -308,6 +309,13 @@
hw_p->print_speed = 1; /* print speed message again next time */
#endif
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+ /* don't bypass the TAHOE0/TAHOE1 cores for Linux */
+ mfsdr(SDR0_ETH_CFG, eth_cfg);
+ eth_cfg &= ~(SDR0_ETH_CFG_TAHOE0_BYPASS | SDR0_ETH_CFG_TAHOE1_BYPASS);
+ mtsdr(SDR0_ETH_CFG, eth_cfg);
+#endif
+
return;
}
@@ -494,11 +502,18 @@
u32 zmiifer; /* ZMII0_FER reg. */
u32 rmiifer; /* RGMII0_FER reg. Bridge 0 */
u32 rmiifer1; /* RGMII0_FER reg. Bridge 1 */
+ int mode;
zmiifer = 0;
rmiifer = 0;
rmiifer1 = 0;
+#if defined(CONFIG_460EX)
+ mode = 9;
+#else
+ mode = 10;
+#endif
+
/* TODO:
* NOTE: 460GT has 2 RGMII bridge cores:
* emac0 ------ RGMII0_BASE
@@ -520,7 +535,7 @@
* Right now only 2*RGMII is supported. Please extend when needed.
* sr - 2008-02-19
*/
- switch (9) {
+ switch (mode) {
case 1:
/* 1 MII - 460EX */
/* GMC0 EMAC4_0, ZMII Bridge */
@@ -836,10 +851,12 @@
reg = CONFIG_PHY1_ADDR;
break;
#endif
-#if defined (CONFIG_440GX)
+#if defined (CONFIG_PHY2_ADDR)
case 2:
reg = CONFIG_PHY2_ADDR;
break;
+#endif
+#if defined (CONFIG_PHY3_ADDR)
case 3:
reg = CONFIG_PHY3_ADDR;
break;
@@ -1131,7 +1148,7 @@
#endif
#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
- mtdcr (malrxctp8r, hw_p->rx);
+ mtdcr (malrxctp8r, hw_p->rx_phys);
/* set RX buffer size */
mtdcr (malrcbs8, ENET_MAX_MTU_ALIGNED / 16);
#else
@@ -1160,6 +1177,26 @@
mtdcr (malrcbs3, ENET_MAX_MTU_ALIGNED / 16);
break;
#endif /* CONFIG_440GX */
+#if defined (CONFIG_460GT)
+ case 2:
+ /* setup MAL tx & rx channel pointers */
+ mtdcr (maltxbattr, 0x0);
+ mtdcr (malrxbattr, 0x0);
+ mtdcr (maltxctp2r, hw_p->tx_phys);
+ mtdcr (malrxctp16r, hw_p->rx_phys);
+ /* set RX buffer size */
+ mtdcr (malrcbs16, ENET_MAX_MTU_ALIGNED / 16);
+ break;
+ case 3:
+ /* setup MAL tx & rx channel pointers */
+ mtdcr (maltxbattr, 0x0);
+ mtdcr (malrxbattr, 0x0);
+ mtdcr (maltxctp3r, hw_p->tx_phys);
+ mtdcr (malrxctp24r, hw_p->rx_phys);
+ /* set RX buffer size */
+ mtdcr (malrcbs24, ENET_MAX_MTU_ALIGNED / 16);
+ break;
+#endif /* CONFIG_460GT */
case 0:
default:
/* setup MAL tx & rx channel pointers */
@@ -1866,14 +1903,22 @@
case 2:
memcpy(ethaddr[eth_num + CONFIG_EMAC_NR_START],
bis->bi_enet2addr, 6);
+#if defined(CONFIG_460GT)
+ hw_addr[eth_num] = 0x300;
+#else
hw_addr[eth_num] = 0x400;
+#endif
break;
#endif
#ifdef CONFIG_HAS_ETH3
case 3:
memcpy(ethaddr[eth_num + CONFIG_EMAC_NR_START],
bis->bi_enet3addr, 6);
+#if defined(CONFIG_460GT)
+ hw_addr[eth_num] = 0x400;
+#else
hw_addr[eth_num] = 0x600;
+#endif
break;
#endif
}
