* Add support for RMU board
* Add support for TQM862L at 100/50 MHz
* Patch by Pantelis Antoniou, 02 Jun 2003:
major reconstruction of networking code;
add "ping" support (outgoing only!)
diff --git a/include/cmd_confdefs.h b/include/cmd_confdefs.h
index 18ce6d8..7ab553d 100644
--- a/include/cmd_confdefs.h
+++ b/include/cmd_confdefs.h
@@ -81,6 +81,7 @@
#define CFG_CMD_NAND 0x0000800000000000 /* NAND support */
#define CFG_CMD_BMP 0x0001000000000000 /* BMP support */
#define CFG_CMD_PORTIO 0x0002000000000000 /* Port I/O */
+#define CFG_CMD_PING 0x0004000000000000 /* ping support */
#define CFG_CMD_ALL 0xFFFFFFFFFFFFFFFF /* ALL commands */
@@ -113,6 +114,7 @@
CFG_CMD_NAND | \
CFG_CMD_PCI | \
CFG_CMD_PCMCIA | \
+ CFG_CMD_PING | \
CFG_CMD_REGINFO | \
CFG_CMD_SAVES | \
CFG_CMD_SCSI | \
diff --git a/include/cmd_net.h b/include/cmd_net.h
index e9ca5c5..842cb3e 100644
--- a/include/cmd_net.h
+++ b/include/cmd_net.h
@@ -64,11 +64,24 @@
#define CMD_TBL_DHCP
#endif /* CFG_CMD_DHCP */
+#if (CONFIG_COMMANDS & CFG_CMD_PING)
+#define CMD_TBL_PING MK_CMD_TBL_ENTRY( \
+ "ping", 4, 2, 1, do_ping, \
+ "ping - check if host is reachable\n", \
+ "host\n" \
+),
+
+int do_ping (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+#else
+#define CMD_TBL_PING
+#endif /* CFG_CMD_PING */
+
#else
#define CMD_TBL_BOOTP
#define CMD_TBL_TFTPB
#define CMD_TBL_RARPB
#define CMD_TBL_DHCP
+#define CMD_TBL_PING
#endif /* CFG_CMD_NET */
#endif
diff --git a/include/commproc.h b/include/commproc.h
index d6cf9ba..2d9ab5c 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -1254,7 +1254,11 @@
#define PA_ENET_TXD ((ushort)0x0008)
#define PA_ENET_TCLK ((ushort)0x0200)
#define PA_ENET_RCLK ((ushort)0x0800)
+#if defined(CONFIG_RMU)
+#define PC_ENET_TENA ((uint)0x00000002) /* PC14 */
+#else
#define PB_ENET_TENA ((uint)0x00002000)
+#endif
#define PC_ENET_CLSN ((ushort)0x0040)
#define PC_ENET_RENA ((ushort)0x0080)
diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h
index 653d0c7..1d0aea1 100644
--- a/include/configs/TQM862L.h
+++ b/include/configs/TQM862L.h
@@ -251,14 +251,15 @@
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit
*
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
+ * If this is a 80 MHz or 100 MHz CPU,
+ * set PLL multiplication factor to 5 (5 * 16 = 80, 5 * 20 = 100)
*/
-#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
+#if defined(CONFIG_80MHz) || defined(CONFIG_100MHz)
#define CFG_PLPRCR \
( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
#else /* up to 50 MHz we use a 1:1 clock */
#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif /* CONFIG_80MHz */
+#endif /* CONFIG_80MHz | CONFIG_100MHz */
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
@@ -267,7 +268,7 @@
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
-#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
+#if defined(CONFIG_80MHz) || defined(CONFIG_100MHz) /* use 16/20 MHz * 5 */
#define CFG_SCCR (/* SCCR_TBS | */ \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
@@ -277,7 +278,7 @@
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
-#endif /* CONFIG_80MHz */
+#endif /* CONFIG_80MHz | CONFIG_100MHz */
/*-----------------------------------------------------------------------
* PCMCIA stuff
@@ -346,8 +347,15 @@
/*
* FLASH timing:
*/
-#if defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
+#if defined(CONFIG_100MHz)
+/* 100 MHz CPU - 50 MHz bus:
+ * 0x...926: 9 = OR_CSNT_SAM + OR_BI; 2 = OR_SCY_2_CLK; 6 = OR_TRLX + OR_EHTR
+ * ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
+ OR_SCY_2_CLK | OR_EHTR | OR_BI)
+#elif defined(CONFIG_80MHz)
+/* 80 MHz CPU - 40 MHz bus:
+ * ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | 0 | OR_CSNT_SAM | \
OR_SCY_3_CLK | OR_EHTR | OR_BI)
#elif defined(CONFIG_66MHz)
@@ -415,11 +423,14 @@
* --------------------------------------------
* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
*
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
+ * 50 MHz => 50.000.000 / Divider = 98
+ * 66 Mhz => 66.000.000 / Divider = 129
+ * 80 Mhz => 80.000.000 / Divider = 156
+ * 100 Mhz => 100.000.000 / Divider = 195
*/
-#if defined(CONFIG_80MHz)
+#if defined(CONFIG_100MHz)
+#define CFG_MAMR_PTA 195
+#elif defined(CONFIG_80MHz)
#define CFG_MAMR_PTA 156
#elif defined(CONFIG_66MHz)
#define CFG_MAMR_PTA 129
diff --git a/include/configs/rmu.h b/include/configs/rmu.h
new file mode 100644
index 0000000..0a94714
--- /dev/null
+++ b/include/configs/rmu.h
@@ -0,0 +1,379 @@
+/*
+ * (C) Copyright 2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#undef CONFIG_MPC860
+#define CONFIG_MPC850 1 /* This is a MPC850 CPU */
+#define CONFIG_RPXLITE 1 /* RMU is the RPXlite clone */
+#define CONFIG_RMU 1
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600bps */
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0040000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFA200000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFF800000
+/*%%% #define CFG_FLASH_BASE 0xFFF00000 */
+#if defined(DEBUG) || (CONFIG_COMMANDS & CFG_CMD_IDE)
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE 0xFFF00000
+/*%%% #define CFG_MONITOR_BASE CFG_FLASH_BASE */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 35 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x00740000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_ENV_OFFSET)
+
+/* Address and size of Redundant Environment Sector */
+#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_MLRC10)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+/*%%%#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ *
+ * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
+ */
+/* up to 50 MHz we use a 1:1 clock */
+#define CFG_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF00
+/* up to 50 MHz we use a 1:1 clock */
+#define CFG_SCCR (SCCR_COM00 | SCCR_TBS)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define CFG_DER 0x2002000F*/
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0 and OR0 (FLASH)
+ */
+
+#define FLASH_BASE_PRELIM 0xFE000000 /* FLASH base */
+#define CFG_PRELIM_OR_AM 0xFE000000 /* OR addr mask */
+
+/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
+#define CFG_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)
+
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
+
+/*
+ * BR1 and OR1 (SDRAM)
+ *
+ */
+#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */
+#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CFG_OR_TIMING_SDRAM 0x00000E00
+
+#define CFG_OR1_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+/* RPXLITE mem setting */
+#define CFG_BR3_PRELIM 0xFA400001 /* BCSR */
+#define CFG_OR3_PRELIM 0xFFFF8910
+#define CFG_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */
+#define CFG_OR4_PRELIM 0xFFFE0970
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 20
+
+/*
+ * Refresh clock Prescalar
+ */
+#define CFG_MPTPR MPTPR_PTP_DIV2
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 10 column SDRAM */
+#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
+ MAMR_RLFA_16X | MAMR_WLFA_16X | MAMR_TLFA_16X)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * BCSRx
+ *
+ * Board Status and Control Registers
+ *
+ */
+
+#define BCSR0 0xFA400000
+#define BCSR1 0xFA400001
+#define BCSR2 0xFA400002
+#define BCSR3 0xFA400003
+
+#define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */
+#define BCSR0_ENNVRAM 0x02 /* CS4# Control */
+#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */
+#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */
+#define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */
+#define BCSR0_COLTEST 0x20
+#define BCSR0_ETHLPBK 0x40
+#define BCSR0_ETHEN 0x80
+
+#define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */
+#define BCSR1_PCVCTL6 0x02
+#define BCSR1_PCVCTL5 0x04
+#define BCSR1_PCVCTL4 0x08
+#define BCSR1_IPB5SEL 0x10
+
+#define BCSR2_ENPA5HDR 0x08 /* USB Control */
+#define BCSR2_ENUSBCLK 0x10
+#define BCSR2_USBPWREN 0x20
+#define BCSR2_USBSPD 0x40
+#define BCSR2_USBSUSP 0x80
+
+#define BCSR3_BWRTC 0x01 /* Real Time Clock Battery */
+#define BCSR3_BWNVR 0x02 /* NVRAM Battery */
+#define BCSR3_RDY_BSY 0x04 /* Flash Operation */
+#define BCSR3_RPXL 0x08 /* Reserved (reads back '1') */
+#define BCSR3_D27 0x10 /* Dip Switch settings */
+#define BCSR3_D26 0x20
+#define BCSR3_D25 0x40
+#define BCSR3_D24 0x80
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/sc520_spunk.h b/include/configs/sc520_spunk.h
index 2b5a54d..0a28805 100644
--- a/include/configs/sc520_spunk.h
+++ b/include/configs/sc520_spunk.h
@@ -206,7 +206,7 @@
#define CFG_FIRST_PCI_IRQ 9
#define CFG_SECOND_PCI_IRQ 10
-#define CFG_THIRD_PCI_IRQ 11
+#define CFG_THIRD_PCI_IRQ 11
#define CFG_FORTH_PCI_IRQ 12
diff --git a/include/net.h b/include/net.h
index e4f7cbd..689a90f 100644
--- a/include/net.h
+++ b/include/net.h
@@ -200,7 +200,9 @@
/*
* ICMP stuff (just enough to handle (host) redirect messages)
*/
+#define ICMP_ECHO_REPLY 0 /* Echo reply */
#define ICMP_REDIRECT 5 /* Redirect (change route) */
+#define ICMP_ECHO_REQUEST 8 /* Echo request */
/* Codes for REDIRECT. */
#define ICMP_REDIR_NET 0 /* Redirect Net */
@@ -292,11 +294,15 @@
extern int NetRestartWrap; /* Tried all network devices */
#endif
-typedef enum { BOOTP, RARP, ARP, TFTP, DHCP } proto_t;
+typedef enum { BOOTP, RARP, ARP, TFTP, DHCP, PING, DNS } proto_t;
/* from net/net.c */
extern char BootFile[128]; /* Boot File name */
+#if (CONFIG_COMMANDS & CFG_CMD_PING)
+extern IPaddr_t NetPingIP; /* the ip address to ping */
+#endif
+
/* Initialize the network adapter */
extern int NetLoop(proto_t);
@@ -323,6 +329,9 @@
/* Transmit "NetTxPacket" */
extern void NetSendPacket(volatile uchar *, int);
+/* Transmit UDP packet, performing ARP request if needed */
+extern int NetSendUDPPacket(uchar *ether, IPaddr_t dest, int dport, int sport, int len);
+
/* Processes a received packet */
extern void NetReceive(volatile uchar *, int);
@@ -373,6 +382,9 @@
/* Convert an IP address to a string */
extern void ip_to_string (IPaddr_t x, char *s);
+/* Convert a string to ip address */
+extern IPaddr_t string_to_ip(char *s);
+
/* read an IP address from a environment variable */
extern IPaddr_t getenv_IPaddr (char *);
