Merge branch 'next' of git://git.denx.de/u-boot-nand-flash into next
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index 313f9f3..c90f86b 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -466,143 +466,6 @@
#endif
}
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB3 devices to 0.
- | Set PLB3 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB4 devices to 0.
- +-------------------------------------------------------------------------*/
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*-------------------------------------------------------------------------+
- | Set Nebula PLB4 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
- * pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*--------------------------------------------------------------------------+
- | Write the PowerPC440 EP PCI Configuration regs.
- | Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- | Enable PowerPC440 EP to act as a PCI memory target (PTM).
- +--------------------------------------------------------------------------*/
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-
/*----------------------------------------------------------------------------+
| is_powerpc440ep_pass1.
+----------------------------------------------------------------------------*/
diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c
index 9a8ca8e..13a0dac 100644
--- a/board/amcc/canyonlands/canyonlands.c
+++ b/board/amcc/canyonlands/canyonlands.c
@@ -326,43 +326,6 @@
}
#endif
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*
- * Disable everything
- */
- out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
- out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
- out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
- out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- */
- out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out_le32((void *)PCIL0_PIM0LAH, 0);
- out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
- out_le32((void *)PCIL0_BAR0, 0);
-
- /*
- * Program the board's subsystem id/vendor id
- */
- out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI)
int board_pcie_first(void)
{
diff --git a/board/amcc/ebony/ebony.c b/board/amcc/ebony/ebony.c
index 1524b53..923dbca 100644
--- a/board/amcc/ebony/ebony.c
+++ b/board/amcc/ebony/ebony.c
@@ -164,73 +164,3 @@
return (128 * 1024 * 1024); /* 128 MB */
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
-
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long strap;
-
- /*--------------------------------------------------------------------------+
- * The ebony board is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *--------------------------------------------------------------------------*/
- strap = mfdcr(CPC0_STRP1);
- if ((strap & 0x00100000) == 0) {
- printf("PCI: CPC0_STRP1[PAE] not set.\n");
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r(PCIL0_PIM0SA, 0); /* disable */
- out32r(PCIL0_PIM1SA, 0); /* disable */
- out32r(PCIL0_PIM2SA, 0); /* disable */
- out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIL0_PIM0LAH, 0);
- out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
- out32r(PCIL0_BAR0, 0);
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
index f43e764..86dc923 100644
--- a/board/amcc/katmai/katmai.c
+++ b/board/amcc/katmai/katmai.c
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2007-2008
+ * (C) Copyright 2007-2009
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* See file CREDITS for list of people who contributed to this
@@ -260,75 +260,6 @@
return (SDRAM_CLKTR_CLKP_90_DEG_ADV);
}
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller * hose )
-{
- unsigned long strap;
-
- /*-------------------------------------------------------------------+
- * The katmai board is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *-------------------------------------------------------------------*/
- mfsdr(SDR0_SDSTP1, strap);
- if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
- printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*-------------------------------------------------------------------+
- * Disable everything
- *-------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*-------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- *-------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIL0_BAR0, 0 );
-
- /*-------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *-------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI)
int board_pcie_card_present(int port)
{
diff --git a/board/amcc/kilauea/kilauea.c b/board/amcc/kilauea/kilauea.c
index c4f8a64..2f99ea1 100644
--- a/board/amcc/kilauea/kilauea.c
+++ b/board/amcc/kilauea/kilauea.c
@@ -285,25 +285,6 @@
return (0);
}
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller * hose )
-{
- return 0;
-}
-#endif /* defined(CONFIG_PCI) */
-
#if defined(CONFIG_POST)
/*
* Returns 1 if keys pressed to start the power-on long-running tests
diff --git a/board/amcc/luan/luan.c b/board/amcc/luan/luan.c
index 94ba643..332d170 100644
--- a/board/amcc/luan/luan.c
+++ b/board/amcc/luan/luan.c
@@ -127,79 +127,6 @@
}
/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init( struct pci_controller *hose )
-{
- unsigned long strap;
-
- /*--------------------------------------------------------------------------+
- * The luan board is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *--------------------------------------------------------------------------*/
- mfsdr(SDR0_SDSTP1, strap);
- if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
- printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
-
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
-/*************************************************************************
* hw_watchdog_reset
*
* This routine is called to reset (keep alive) the watchdog timer
diff --git a/board/amcc/makalu/makalu.c b/board/amcc/makalu/makalu.c
index 43b9bc6..3d860af 100644
--- a/board/amcc/makalu/makalu.c
+++ b/board/amcc/makalu/makalu.c
@@ -237,25 +237,6 @@
return (0);
}
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller * hose )
-{
- return 0;
-}
-#endif /* defined(CONFIG_PCI) */
-
#if defined(CONFIG_POST)
/*
* Returns 1 if keys pressed to start the power-on long-running tests
diff --git a/board/amcc/ocotea/ocotea.c b/board/amcc/ocotea/ocotea.c
index 2f64764..951a8b5 100644
--- a/board/amcc/ocotea/ocotea.c
+++ b/board/amcc/ocotea/ocotea.c
@@ -275,78 +275,6 @@
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
-
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller * hose )
-{
- unsigned long strap;
-
- /*--------------------------------------------------------------------------+
- * The ocotea board is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *--------------------------------------------------------------------------*/
- mfsdr(SDR0_SDSTP1, strap);
- if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
- printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
void fpga_init(void)
{
unsigned long group;
diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
index 4393820..cb34c9d 100644
--- a/board/amcc/sequoia/sequoia.c
+++ b/board/amcc/sequoia/sequoia.c
@@ -364,151 +364,12 @@
/*
* Assign interrupts to PCI devices.
*/
-void sequoia_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2);
}
#endif
-/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- */
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*
- * Set Nebula PLB4 arbiter to fair mode.
- */
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
-#ifdef CONFIG_PCI_PNP
- hose->fixup_irq = sequoia_pci_fixup_irq;
-#endif
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*
- * Write the PowerPC440 EP PCI Configuration regs.
- * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- * Enable PowerPC440 EP to act as a PCI memory target (PTM).
- */
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-
#if defined(CONFIG_POST)
/*
* Returns 1 if keys pressed to start the power-on long-running tests
diff --git a/board/amcc/taishan/taishan.c b/board/amcc/taishan/taishan.c
index 81e8fe1..279fae2 100644
--- a/board/amcc/taishan/taishan.c
+++ b/board/amcc/taishan/taishan.c
@@ -209,76 +209,6 @@
return (0);
}
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller * hose )
-{
- unsigned long strap;
-
- /*--------------------------------------------------------------------------+
- * The ocotea board is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *--------------------------------------------------------------------------*/
- mfsdr(SDR0_SDSTP1, strap);
- if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
- printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#ifdef CONFIG_POST
/*
* Returns 1 if keys pressed to start the power-on long-running tests
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c
index e416eeb..98c1f3b 100644
--- a/board/amcc/yosemite/yosemite.c
+++ b/board/amcc/yosemite/yosemite.c
@@ -353,143 +353,6 @@
}
/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB3 devices to 0.
- | Set PLB3 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB4 devices to 0.
- +-------------------------------------------------------------------------*/
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*-------------------------------------------------------------------------+
- | Set Nebula PLB4 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
- * pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*--------------------------------------------------------------------------+
- | Write the PowerPC440 EP PCI Configuration regs.
- | Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- | Enable PowerPC440 EP to act as a PCI memory target (PTM).
- +--------------------------------------------------------------------------*/
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-
-/*************************************************************************
* hw_watchdog_reset
*
* This routine is called to reset (keep alive) the watchdog timer
diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index 7315033..e0d19bc 100644
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -588,75 +588,6 @@
return default_val;
}
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller * hose )
-{
- unsigned long strap;
-
- /*-------------------------------------------------------------------+
- * The yucca board is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *-------------------------------------------------------------------*/
- mfsdr(SDR0_SDSTP1, strap);
- if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
- printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*-------------------------------------------------------------------+
- * Disable everything
- *-------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*-------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- *-------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIL0_BAR0, 0 );
-
- /*-------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *-------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI)
int board_pcie_card_present(int port)
{
diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c
index 8f9f950..111cce5 100644
--- a/board/esd/du440/du440.c
+++ b/board/esd/du440/du440.c
@@ -360,144 +360,6 @@
return (0);
}
-/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- */
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*
- * Set Nebula PLB4 arbiter to fair mode.
- */
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- PCI_VENDOR_ID_ESDGMBH);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, PCI_DEVICE_ID_DU440);
-
- pci_write_config_word(0, PCI_CLASS_SUB_CODE, PCI_CLASS_BRIDGE_HOST);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*
- * Write the PowerPC440 EP PCI Configuration regs.
- * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- * Enable PowerPC440 EP to act as a PCI memory target (PTM).
- */
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-
int last_stage_init(void)
{
int e, i;
diff --git a/board/esd/du440/du440.h b/board/esd/du440/du440.h
index a124a7e..37697ec 100644
--- a/board/esd/du440/du440.h
+++ b/board/esd/du440/du440.h
@@ -38,6 +38,3 @@
#define PWR_RDY 0x10
#define CPLD_IRQ (32+30)
-
-#define PCI_VENDOR_ID_ESDGMBH 0x12fe
-#define PCI_DEVICE_ID_DU440 0x0444
diff --git a/board/esd/pmc440/config.mk b/board/esd/pmc440/config.mk
index 0c4d582..91e65ec 100644
--- a/board/esd/pmc440/config.mk
+++ b/board/esd/pmc440/config.mk
@@ -20,10 +20,6 @@
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
-#
-# AMCC 440EPx Reference Platform (Sequoia) board
-#
-
sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
ifndef TEXT_BASE
diff --git a/board/esd/pmc440/pmc440.c b/board/esd/pmc440/pmc440.c
index 10901b4..d0ff080 100644
--- a/board/esd/pmc440/pmc440.c
+++ b/board/esd/pmc440/pmc440.c
@@ -39,6 +39,8 @@
#include <miiphy.h>
#endif
#include <serial.h>
+#include <asm/4xx_pci.h>
+
#include "fpga.h"
#include "pmc440.h"
@@ -478,7 +480,7 @@
/*
* Assign interrupts to PCI devices. Some OSs rely on this.
*/
-void pmc440_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
unsigned char int_line[] = {IRQ_PCIC, IRQ_PCID, IRQ_PCIA, IRQ_PCIB};
@@ -488,64 +490,6 @@
#endif
/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- */
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*
- * Set Nebula PLB4 arbiter to fair mode.
- */
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
-#ifdef CONFIG_PCI_PNP
- hose->fixup_irq = pmc440_pci_fixup_irq;
-#endif
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*
* pci_target_init
*
* The bootstrap configuration provides default settings for the pci
@@ -658,24 +602,16 @@
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
/*
- * pci_master_init
+ * Override weak default pci_master_init()
*/
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
- unsigned short temp_short;
-
/*
- * Write the PowerPC440 EP PCI Configuration regs.
- * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- * Enable PowerPC440 EP to act as a PCI memory target (PTM).
+ * Only configure the master in monach mode
*/
- if (is_monarch()) {
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
- }
+ if (is_monarch())
+ __pci_master_init(hose);
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
diff --git a/board/gdsys/gdppc440etx/gdppc440etx.c b/board/gdsys/gdppc440etx/gdppc440etx.c
index 92f5d82..ecbc3c3 100644
--- a/board/gdsys/gdppc440etx/gdppc440etx.c
+++ b/board/gdsys/gdppc440etx/gdppc440etx.c
@@ -29,6 +29,7 @@
#include <ppc4xx.h>
#include <asm/processor.h>
#include <asm/io.h>
+#include <asm/4xx_pci.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -158,55 +159,13 @@
}
/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
+ * Override weak pci_pre_init()
*/
#if defined(CONFIG_PCI)
int pci_pre_init(struct pci_controller *hose)
{
- unsigned long addr;
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*
- * Set Nebula PLB4 arbiter to fair mode.
- */
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
+ /* First call common code */
+ __pci_pre_init(hose);
/* enable 66 MHz ext. Clock */
out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x00008000);
@@ -215,87 +174,3 @@
return 1;
}
#endif /* defined(CONFIG_PCI) */
-
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Set up Direct MMIO registers
- */
-
- /*
- * PowerPC440 EP PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIL0_PMM0MA, 0x00000000); /* disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
- out32r(PCIL0_PMM0PCIHA, 0x00000000);
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M, no prefetch, enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
- out32r(PCIL0_PMM1PCIHA, 0x00000000);
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M, no prefetch, enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001);
- out32r(PCIL0_PTM1LA, 0);
- out32r(PCIL0_PTM2MS, 0);
- out32r(PCIL0_PTM2LA, 0);
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*
- * pci_master_init
- *
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*
- * Write the PowerPC440 EP PCI Configuration regs.
- * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- * Enable PowerPC440 EP to act as a PCI memory target (PTM).
- */
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
diff --git a/board/gdsys/intip/intip.c b/board/gdsys/intip/intip.c
index 49d2451..23a10c4 100644
--- a/board/gdsys/intip/intip.c
+++ b/board/gdsys/intip/intip.c
@@ -141,43 +141,6 @@
return 0;
}
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Disable everything
- */
- out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
- out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
- out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
- out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- */
- out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out_le32((void *)PCIL0_PIM0LAH, 0);
- out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
- out_le32((void *)PCIL0_BAR0, 0);
-
- /*
- * Program the board's subsystem id/vendor id
- */
- out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
int board_early_init_r(void)
{
/*
diff --git a/board/korat/korat.c b/board/korat/korat.c
index b0e6a56..f942052 100644
--- a/board/korat/korat.c
+++ b/board/korat/korat.c
@@ -35,6 +35,7 @@
#include <asm/io.h>
#include <asm/ppc4xx-uic.h>
#include <asm/processor.h>
+#include <asm/4xx_pci.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -594,71 +595,13 @@
/*
* Assign interrupts to PCI devices.
*/
-void korat_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2);
}
#endif
/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- */
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*
- * Set Nebula PLB4 arbiter to fair mode.
- */
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
-#if defined(CONFIG_PCI_PNP)
- hose->fixup_irq = korat_pci_fixup_irq;
-#endif
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*
* pci_target_init
*
* The bootstrap configuration provides default settings for the pci
@@ -668,60 +611,8 @@
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller *hose)
{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0x80000000-0xBFFFFFFF
- * ==> PCI address 0x80000000-0xBFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA,
- CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM1LA,
- CONFIG_SYS_PCI_MEMBASE + 0x20000000); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA,
- CONFIG_SYS_PCI_MEMBASE + 0x20000000); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+ /* First do 440EP(x) common setup */
+ __pci_target_init(hose);
/*
* Set up Configuration registers for on-board NEC uPD720101 USB
@@ -731,23 +622,6 @@
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*
- * Write the PowerPC440 EP PCI Configuration regs.
- * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- * Enable PowerPC440 EP to act as a PCI memory target (PTM).
- */
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif
-
#if defined(CONFIG_POST)
/*
* Returns 1 if keys pressed to start the power-on long-running tests
diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c
index 09ba2b9..415e036 100644
--- a/board/lwmon5/lwmon5.c
+++ b/board/lwmon5/lwmon5.c
@@ -275,143 +275,6 @@
return (0);
}
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB3 devices to 0.
- | Set PLB3 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB4 devices to 0.
- +-------------------------------------------------------------------------*/
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*-------------------------------------------------------------------------+
- | Set Nebula PLB4 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440EPX PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
- * pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*--------------------------------------------------------------------------+
- | Write the PowerPC440 EP PCI Configuration regs.
- | Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- | Enable PowerPC440 EP to act as a PCI memory target (PTM).
- +--------------------------------------------------------------------------*/
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-
void hw_watchdog_reset(void)
{
int val;
diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c
index 7ffc262..8615645 100644
--- a/board/netstal/hcu5/hcu5.c
+++ b/board/netstal/hcu5/hcu5.c
@@ -22,6 +22,8 @@
#include <asm/processor.h>
#include <ppc440.h>
#include <asm/io.h>
+#include <asm/4xx_pci.h>
+
#include "../common/nm.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -377,88 +379,14 @@
}
/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- */
-void pci_target_init(struct pci_controller *hose)
-{
- if (!board_with_pci()) { return; }
- /*
- * Set up Direct MMIO registers
- *
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF ==> PCI address
- * 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0MA, 0x00000000);
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- /* 512M + No prefetching, and enable region */
- out32r(PCIL0_PMM0MA, 0xE0000001);
-
- /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1MA, 0x00000000);
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- /* 512M + No prefetching, and enable region */
- out32r(PCIL0_PMM1MA, 0xE0000001);
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-}
-
-/*
- * pci_master_init
- *
+ * Override weak default pci_master_init()
*/
void pci_master_init(struct pci_controller *hose)
{
- unsigned short temp_short;
- if (!board_with_pci()) { return; }
+ if (!board_with_pci())
+ return;
- /*---------------------------------------------------------------
- * Write the PowerPC440 EP PCI Configuration regs.
- * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- * Enable PowerPC440 EP to act as a PCI memory target (PTM).
- *--------------------------------------------------------------*/
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
+ __pci_master_init(hose);
}
#endif /* defined(CONFIG_PCI) */
diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c
index 2155711..ce1e616 100644
--- a/board/pcs440ep/pcs440ep.c
+++ b/board/pcs440ep/pcs440ep.c
@@ -551,143 +551,6 @@
}
/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB3 devices to 0.
- | Set PLB3 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB4 devices to 0.
- +-------------------------------------------------------------------------*/
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*-------------------------------------------------------------------------+
- | Set Nebula PLB4 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
- * pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*--------------------------------------------------------------------------+
- | Write the PowerPC440 EP PCI Configuration regs.
- | Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- | Enable PowerPC440 EP to act as a PCI memory target (PTM).
- +--------------------------------------------------------------------------*/
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-
-/*************************************************************************
* hw_watchdog_reset
*
* This routine is called to reset (keep alive) the watchdog timer
diff --git a/board/prodrive/alpr/alpr.c b/board/prodrive/alpr/alpr.c
index e9e2bf3..6615327 100644
--- a/board/prodrive/alpr/alpr.c
+++ b/board/prodrive/alpr/alpr.c
@@ -29,6 +29,7 @@
#include <ppc4xx_enet.h>
#include <miiphy.h>
#include <asm/processor.h>
+#include <asm/4xx_pci.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -144,78 +145,20 @@
return (0);
}
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller * hose )
+/*
+ * Override weak pci_pre_init()
+ */
+int pci_pre_init(struct pci_controller *hose)
{
- unsigned long strap;
-
- /*--------------------------------------------------------------------------+
- * The ocotea board is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *--------------------------------------------------------------------------*/
- mfsdr(SDR0_SDSTP1, strap);
- if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
- printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
+ if (__pci_pre_init(hose) == 0)
return 0;
- }
/* FPGA Init */
- alpr_fpga_init ();
+ alpr_fpga_init();
return 1;
}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
/*************************************************************************
* Override weak is_pci_host()
@@ -232,8 +175,6 @@
*
*
************************************************************************/
-#if defined(CONFIG_PCI)
-
static void wait_for_pci_ready(void)
{
/*
diff --git a/board/prodrive/p3p440/p3p440.c b/board/prodrive/p3p440/p3p440.c
index e074007..020f66d 100644
--- a/board/prodrive/p3p440/p3p440.c
+++ b/board/prodrive/p3p440/p3p440.c
@@ -165,76 +165,6 @@
}
/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long strap;
-
- /*--------------------------------------------------------------------------+
- * The P3P440 board is always configured as the host & requires the
- * PCI arbiter to be disabled because it's an PMC module.
- *--------------------------------------------------------------------------*/
- strap = mfdcr(CPC0_STRP1);
- if (strap & 0x00100000) {
- printf("PCI: CPC0_STRP1[PAE] set.\n");
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r(PCIL0_PIM0SA, 0); /* disable */
- out32r(PCIL0_PIM1SA, 0); /* disable */
- out32r(PCIL0_PIM2SA, 0); /* disable */
- out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIL0_PIM0LAH, 0);
- out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
- out32r(PCIL0_BAR0, 0);
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
* Override weak is_pci_host()
*
* This routine is called to determine if a pci scan should be
diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c
index 5749084..6b91074 100644
--- a/board/sandburst/common/sb_common.c
+++ b/board/sandburst/common/sb_common.c
@@ -300,78 +300,6 @@
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
-
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller * hose )
-{
- unsigned long strap;
-
- /*--------------------------------------------------------------------------+
- * The metrobox is always configured as the host & requires the
- * PCI arbiter to be enabled.
- *--------------------------------------------------------------------------*/
- mfsdr(SDR0_SDSTP1, strap);
- if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
- printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
- return 0;
- }
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
/*************************************************************************
* board_get_enetaddr
*
diff --git a/board/xes/xpedite1000/xpedite1000.c b/board/xes/xpedite1000/xpedite1000.c
index 0c4cf94..b4cbb2f 100644
--- a/board/xes/xpedite1000/xpedite1000.c
+++ b/board/xes/xpedite1000/xpedite1000.c
@@ -136,6 +136,8 @@
}
/*
+ * Override weak pci_pre_init()
+ *
* This routine is called just prior to registering the hose and gives
* the board the opportunity to check things. Returning a value of zero
* indicates that things are bad & PCI initialization should be aborted.
@@ -144,7 +146,6 @@
* (add regions, override default access routines, etc) or perform
* certain pre-initialization actions.
*/
-
#if defined(CONFIG_PCI)
int pci_pre_init(struct pci_controller * hose)
{
@@ -166,38 +167,6 @@
}
#endif /* defined(CONFIG_PCI) */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-/*
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-void pci_target_init(struct pci_controller * hose)
-{
- /* Disable everything */
- out32r(PCIL0_PIM0SA, 0);
- out32r(PCIL0_PIM1SA, 0);
- out32r(PCIL0_PIM2SA, 0);
- out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- */
- out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIL0_PIM0LAH, 0);
- out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
- out32r(PCIL0_BAR0, 0);
-
- /* Program the board's subsystem id/vendor id */
- out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI)
/*
* Override weak is_pci_host()
diff --git a/cpu/ppc4xx/4xx_pci.c b/cpu/ppc4xx/4xx_pci.c
index 40017f4..eed4534 100644
--- a/cpu/ppc4xx/4xx_pci.c
+++ b/cpu/ppc4xx/4xx_pci.c
@@ -73,23 +73,30 @@
#include <common.h>
#include <command.h>
-#if !defined(CONFIG_440)
#include <asm/4xx_pci.h>
-#endif
#include <asm/processor.h>
+#include <asm/io.h>
#include <pci.h>
#ifdef CONFIG_PCI
DECLARE_GLOBAL_DATA_PTR;
+#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
+
+#if defined(CONFIG_PMC405)
+ushort pmc405_pci_subsys_deviceid(void);
+#endif
+
+/*#define DEBUG*/
+
/*
* Board-specific pci initialization
* Platform code can reimplement pci_pre_init() if needed
*/
int __pci_pre_init(struct pci_controller *hose)
{
-#if defined (CONFIG_405EP)
+#if defined(CONFIG_405EP)
/*
* Enable the internal PCI arbiter by default.
*
@@ -105,15 +112,8 @@
return 1;
}
-int pci_pre_init(struct pci_controller *hose) __attribute__((weak, alias("__pci_pre_init")));
-
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
-
-#if defined(CONFIG_PMC405)
-ushort pmc405_pci_subsys_deviceid(void);
-#endif
-
-/*#define DEBUG*/
+int pci_pre_init(struct pci_controller *hose)
+ __attribute__((weak, alias("__pci_pre_init")));
int __is_pci_host(struct pci_controller *hose)
{
@@ -231,7 +231,7 @@
pciauto_region_init(hose->pci_fb);
/* Let board change/modify hose & do initial checks */
- if (pci_pre_init (hose) == 0) {
+ if (pci_pre_init(hose) == 0) {
printf("PCI: Board-specific initialization failed.\n");
printf("PCI: Configuration aborted.\n");
return;
@@ -499,6 +499,211 @@
int is_pci_host(struct pci_controller *hose)
__attribute__((weak, alias("__is_pci_host")));
+#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440GRX)
+
+#if defined(CONFIG_SYS_PCI_TARGET_INIT)
+/*
+ * pci_target_init
+ *
+ * The bootstrap configuration provides default settings for the pci
+ * inbound map (PIM). But the bootstrap config choices are limited and
+ * may not be sufficient for a given board.
+ */
+void __pci_target_init(struct pci_controller *hose)
+{
+ /*
+ * Set up Direct MMIO registers
+ */
+
+ /*
+ * PowerPC440 EP PCI Master configuration.
+ * Map one 1Gig range of PLB/processor addresses to PCI memory space.
+ * PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
+ * Use byte reversed out routines to handle endianess.
+ * Make this region non-prefetchable.
+ */
+ /* PMM0 Mask/Attribute - disabled b4 setting */
+ out_le32((void *)PCIL0_PMM0MA, 0x00000000);
+ /* PMM0 Local Address */
+ out_le32((void *)PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);
+ /* PMM0 PCI Low Address */
+ out_le32((void *)PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
+ /* PMM0 PCI High Address */
+ out_le32((void *)PCIL0_PMM0PCIHA, 0x00000000);
+ /* 512M + No prefetching, and enable region */
+ out_le32((void *)PCIL0_PMM0MA, 0xE0000001);
+
+ /* PMM1 Mask/Attribute - disabled b4 setting */
+ out_le32((void *)PCIL0_PMM1MA, 0x00000000);
+ /* PMM1 Local Address */
+ out_le32((void *)PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);
+ /* PMM1 PCI Low Address */
+ out_le32((void *)PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
+ /* PMM1 PCI High Address */
+ out_le32((void *)PCIL0_PMM1PCIHA, 0x00000000);
+ /* 512M + No prefetching, and enable region */
+ out_le32((void *)PCIL0_PMM1MA, 0xE0000001);
+
+ out_le32((void *)PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out_le32((void *)PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out_le32((void *)PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out_le32((void *)PCIL0_PTM2LA, 0); /* Local Addr. Reg */
+
+ /*
+ * Set up Configuration registers
+ */
+
+ /* Program the board's subsystem id/vendor id */
+ pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
+
+ /* Configure command register as bus master */
+ pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
+
+ /* 240nS PCI clock */
+ pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
+
+ /* No error reporting */
+ pci_write_config_word(0, PCI_ERREN, 0);
+
+ pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+}
+#endif /* CONFIG_SYS_PCI_TARGET_INIT */
+
+/*
+ * pci_pre_init
+ *
+ * This routine is called just prior to registering the hose and gives
+ * the board the opportunity to check things. Returning a value of zero
+ * indicates that things are bad & PCI initialization should be aborted.
+ *
+ * Different boards may wish to customize the pci controller structure
+ * (add regions, override default access routines, etc) or perform
+ * certain pre-initialization actions.
+ *
+ */
+int __pci_pre_init(struct pci_controller *hose)
+{
+ u32 reg;
+
+ /*
+ * Set priority for all PLB3 devices to 0.
+ * Set PLB3 arbiter to fair mode.
+ */
+ mfsdr(SD0_AMP1, reg);
+ mtsdr(SD0_AMP1, (reg & 0x000000FF) | 0x0000FF00);
+ reg = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, reg | 0x80000000);
+
+ /*
+ * Set priority for all PLB4 devices to 0.
+ */
+ mfsdr(SD0_AMP0, reg);
+ mtsdr(SD0_AMP0, (reg & 0x000000FF) | 0x0000FF00);
+ reg = mfdcr(PLB4_ACR) | 0xa0000000;
+ mtdcr(PLB4_ACR, reg);
+
+ /*
+ * Set Nebula PLB4 arbiter to fair mode.
+ */
+ /* Segment0 */
+ reg = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ reg = (reg & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ reg = (reg & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ reg = (reg & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, reg);
+
+ /* Segment1 */
+ reg = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ reg = (reg & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ reg = (reg & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ reg = (reg & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, reg);
+
+#if defined(CONFIG_SYS_PCI_BOARD_FIXUP_IRQ)
+ hose->fixup_irq = board_pci_fixup_irq;
+#endif
+
+ return 1;
+}
+
+#else /* defined(CONFIG_440EP) ... */
+
+#if defined(CONFIG_SYS_PCI_TARGET_INIT)
+void __pci_target_init(struct pci_controller * hose)
+{
+ /*
+ * Disable everything
+ */
+ out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
+ out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
+
+ /*
+ * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
+ * strapping options do not support sizes such as 128/256 MB.
+ */
+ out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
+ out_le32((void *)PCIL0_PIM0LAH, 0);
+ out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
+ out_le32((void *)PCIL0_BAR0, 0);
+
+ /*
+ * Program the board's subsystem id/vendor id
+ */
+ out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
+
+ out_le16((void *)PCIL0_CMD, in_le16((void *)PCIL0_CMD) |
+ PCI_COMMAND_MEMORY);
+}
+#endif /* CONFIG_SYS_PCI_TARGET_INIT */
+
+int __pci_pre_init(struct pci_controller *hose)
+{
+ /*
+ * This board is always configured as the host & requires the
+ * PCI arbiter to be enabled.
+ */
+ if (!pci_arbiter_enabled()) {
+ printf("PCI: PCI Arbiter disabled!\n");
+ return 0;
+ }
+
+ return 1;
+}
+
+#endif /* defined(CONFIG_440EP) ... */
+
+#if defined(CONFIG_SYS_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller * hose)
+ __attribute__((weak, alias("__pci_target_init")));
+#endif /* CONFIG_SYS_PCI_TARGET_INIT */
+
+int pci_pre_init(struct pci_controller *hose)
+ __attribute__((weak, alias("__pci_pre_init")));
+
+#if defined(CONFIG_SYS_PCI_MASTER_INIT)
+void __pci_master_init(struct pci_controller *hose)
+{
+ u16 reg;
+
+ /*
+ * Write the PowerPC440 EP PCI Configuration regs.
+ * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
+ * Enable PowerPC440 EP to act as a PCI memory target (PTM).
+ */
+ pci_read_config_word(0, PCI_COMMAND, ®);
+ pci_write_config_word(0, PCI_COMMAND, reg |
+ PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
+}
+void pci_master_init(struct pci_controller *hose)
+ __attribute__((weak, alias("__pci_master_init")));
+#endif /* CONFIG_SYS_PCI_MASTER_INIT */
+
int pci_440_init (struct pci_controller *hose)
{
int reg_num = 0;
@@ -568,7 +773,7 @@
pci_setup_indirect(hose, PCIL0_CFGADR, PCIL0_CFGDATA);
/* Let board change/modify hose & do initial checks */
- if (pci_pre_init (hose) == 0) {
+ if (pci_pre_init(hose) == 0) {
printf("PCI: Board-specific initialization failed.\n");
printf("PCI: Configuration aborted.\n");
return -1;
diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c
index e1b00a7..73d4d06 100644
--- a/cpu/ppc4xx/cpu.c
+++ b/cpu/ppc4xx/cpu.c
@@ -81,7 +81,7 @@
#if defined(CONFIG_PCI) && !defined(CONFIG_IOP480) && \
!defined(CONFIG_405) && !defined(CONFIG_405EX)
-static int pci_arbiter_enabled(void)
+int pci_arbiter_enabled(void)
{
#if defined(CONFIG_405GP)
return (mfdcr(CPC0_PSR) & PSR_PCI_ARBIT_EN);
diff --git a/drivers/i2c/omap24xx_i2c.c b/drivers/i2c/omap24xx_i2c.c
index 1a4c8c9..ff18991 100644
--- a/drivers/i2c/omap24xx_i2c.c
+++ b/drivers/i2c/omap24xx_i2c.c
@@ -29,6 +29,11 @@
static u16 wait_for_pin (void);
static void flush_fifo(void);
+static struct i2c *i2c_base = (struct i2c *)I2C_DEFAULT_BASE;
+
+static unsigned int bus_initialized[I2C_BUS_MAX];
+static unsigned int current_bus;
+
void i2c_init (int speed, int slaveadd)
{
int psc, fsscll, fssclh;
@@ -95,30 +100,32 @@
sclh = (unsigned int)fssclh;
}
- writew(0x2, I2C_SYSC); /* for ES2 after soft reset */
+ writew(0x2, &i2c_base->sysc); /* for ES2 after soft reset */
udelay(1000);
- writew(0x0, I2C_SYSC); /* will probably self clear but */
+ writew(0x0, &i2c_base->sysc); /* will probably self clear but */
- if (readw (I2C_CON) & I2C_CON_EN) {
- writew (0, I2C_CON);
+ if (readw (&i2c_base->con) & I2C_CON_EN) {
+ writew (0, &i2c_base->con);
udelay (50000);
}
- writew(psc, I2C_PSC);
- writew(scll, I2C_SCLL);
- writew(sclh, I2C_SCLH);
+ writew(psc, &i2c_base->psc);
+ writew(scll, &i2c_base->scll);
+ writew(sclh, &i2c_base->sclh);
/* own address */
- writew (slaveadd, I2C_OA);
- writew (I2C_CON_EN, I2C_CON);
+ writew (slaveadd, &i2c_base->oa);
+ writew (I2C_CON_EN, &i2c_base->con);
/* have to enable intrrupts or OMAP i2c module doesn't work */
writew (I2C_IE_XRDY_IE | I2C_IE_RRDY_IE | I2C_IE_ARDY_IE |
- I2C_IE_NACK_IE | I2C_IE_AL_IE, I2C_IE);
+ I2C_IE_NACK_IE | I2C_IE_AL_IE, &i2c_base->ie);
udelay (1000);
flush_fifo();
- writew (0xFFFF, I2C_STAT);
- writew (0, I2C_CNT);
+ writew (0xFFFF, &i2c_base->stat);
+ writew (0, &i2c_base->cnt);
+
+ bus_initialized[current_bus] = 1;
}
static int i2c_read_byte (u8 devaddr, u8 regoffset, u8 * value)
@@ -130,19 +137,19 @@
wait_for_bb ();
/* one byte only */
- writew (1, I2C_CNT);
+ writew (1, &i2c_base->cnt);
/* set slave address */
- writew (devaddr, I2C_SA);
+ writew (devaddr, &i2c_base->sa);
/* no stop bit needed here */
- writew (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX, I2C_CON);
+ writew (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX, &i2c_base->con);
status = wait_for_pin ();
if (status & I2C_STAT_XRDY) {
/* Important: have to use byte access */
- writeb (regoffset, I2C_DATA);
+ writeb (regoffset, &i2c_base->data);
udelay (20000);
- if (readw (I2C_STAT) & I2C_STAT_NACK) {
+ if (readw (&i2c_base->stat) & I2C_STAT_NACK) {
i2c_error = 1;
}
} else {
@@ -151,28 +158,28 @@
if (!i2c_error) {
/* free bus, otherwise we can't use a combined transction */
- writew (0, I2C_CON);
- while (readw (I2C_STAT) || (readw (I2C_CON) & I2C_CON_MST)) {
+ writew (0, &i2c_base->con);
+ while (readw (&i2c_base->stat) || (readw (&i2c_base->con) & I2C_CON_MST)) {
udelay (10000);
/* Have to clear pending interrupt to clear I2C_STAT */
- writew (0xFFFF, I2C_STAT);
+ writew (0xFFFF, &i2c_base->stat);
}
wait_for_bb ();
/* set slave address */
- writew (devaddr, I2C_SA);
+ writew (devaddr, &i2c_base->sa);
/* read one byte from slave */
- writew (1, I2C_CNT);
+ writew (1, &i2c_base->cnt);
/* need stop bit here */
writew (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP,
- I2C_CON);
+ &i2c_base->con);
status = wait_for_pin ();
if (status & I2C_STAT_RRDY) {
#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
- *value = readb (I2C_DATA);
+ *value = readb (&i2c_base->data);
#else
- *value = readw (I2C_DATA);
+ *value = readw (&i2c_base->data);
#endif
udelay (20000);
} else {
@@ -180,17 +187,17 @@
}
if (!i2c_error) {
- writew (I2C_CON_EN, I2C_CON);
- while (readw (I2C_STAT)
- || (readw (I2C_CON) & I2C_CON_MST)) {
+ writew (I2C_CON_EN, &i2c_base->con);
+ while (readw (&i2c_base->stat)
+ || (readw (&i2c_base->con) & I2C_CON_MST)) {
udelay (10000);
- writew (0xFFFF, I2C_STAT);
+ writew (0xFFFF, &i2c_base->stat);
}
}
}
flush_fifo();
- writew (0xFFFF, I2C_STAT);
- writew (0, I2C_CNT);
+ writew (0xFFFF, &i2c_base->stat);
+ writew (0, &i2c_base->cnt);
return i2c_error;
}
@@ -203,12 +210,12 @@
wait_for_bb ();
/* two bytes */
- writew (2, I2C_CNT);
+ writew (2, &i2c_base->cnt);
/* set slave address */
- writew (devaddr, I2C_SA);
+ writew (devaddr, &i2c_base->sa);
/* stop bit needed here */
writew (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX |
- I2C_CON_STP, I2C_CON);
+ I2C_CON_STP, &i2c_base->con);
/* wait until state change */
status = wait_for_pin ();
@@ -216,24 +223,24 @@
if (status & I2C_STAT_XRDY) {
#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
/* send out 1 byte */
- writeb (regoffset, I2C_DATA);
- writew (I2C_STAT_XRDY, I2C_STAT);
+ writeb (regoffset, &i2c_base->data);
+ writew (I2C_STAT_XRDY, &i2c_base->stat);
status = wait_for_pin ();
if ((status & I2C_STAT_XRDY)) {
/* send out next 1 byte */
- writeb (value, I2C_DATA);
- writew (I2C_STAT_XRDY, I2C_STAT);
+ writeb (value, &i2c_base->data);
+ writew (I2C_STAT_XRDY, &i2c_base->stat);
} else {
i2c_error = 1;
}
#else
/* send out two bytes */
- writew ((value << 8) + regoffset, I2C_DATA);
+ writew ((value << 8) + regoffset, &i2c_base->data);
#endif
/* must have enough delay to allow BB bit to go low */
udelay (50000);
- if (readw (I2C_STAT) & I2C_STAT_NACK) {
+ if (readw (&i2c_base->stat) & I2C_STAT_NACK) {
i2c_error = 1;
}
} else {
@@ -243,18 +250,18 @@
if (!i2c_error) {
int eout = 200;
- writew (I2C_CON_EN, I2C_CON);
- while ((stat = readw (I2C_STAT)) || (readw (I2C_CON) & I2C_CON_MST)) {
+ writew (I2C_CON_EN, &i2c_base->con);
+ while ((stat = readw (&i2c_base->stat)) || (readw (&i2c_base->con) & I2C_CON_MST)) {
udelay (1000);
/* have to read to clear intrrupt */
- writew (0xFFFF, I2C_STAT);
+ writew (0xFFFF, &i2c_base->stat);
if(--eout == 0) /* better leave with error than hang */
break;
}
}
flush_fifo();
- writew (0xFFFF, I2C_STAT);
- writew (0, I2C_CNT);
+ writew (0xFFFF, &i2c_base->stat);
+ writew (0, &i2c_base->cnt);
return i2c_error;
}
@@ -265,14 +272,14 @@
* you get a bus error
*/
while(1){
- stat = readw(I2C_STAT);
+ stat = readw(&i2c_base->stat);
if(stat == I2C_STAT_RRDY){
#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
- readb(I2C_DATA);
+ readb(&i2c_base->data);
#else
- readw(I2C_DATA);
+ readw(&i2c_base->data);
#endif
- writew(I2C_STAT_RRDY,I2C_STAT);
+ writew(I2C_STAT_RRDY,&i2c_base->stat);
udelay(1000);
}else
break;
@@ -283,7 +290,7 @@
{
int res = 1; /* default = fail */
- if (chip == readw (I2C_OA)) {
+ if (chip == readw (&i2c_base->oa)) {
return res;
}
@@ -291,27 +298,27 @@
wait_for_bb ();
/* try to read one byte */
- writew (1, I2C_CNT);
+ writew (1, &i2c_base->cnt);
/* set slave address */
- writew (chip, I2C_SA);
+ writew (chip, &i2c_base->sa);
/* stop bit needed here */
- writew (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP, I2C_CON);
+ writew (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP, &i2c_base->con);
/* enough delay for the NACK bit set */
udelay (50000);
- if (!(readw (I2C_STAT) & I2C_STAT_NACK)) {
+ if (!(readw (&i2c_base->stat) & I2C_STAT_NACK)) {
res = 0; /* success case */
flush_fifo();
- writew(0xFFFF, I2C_STAT);
+ writew(0xFFFF, &i2c_base->stat);
} else {
- writew(0xFFFF, I2C_STAT); /* failue, clear sources*/
- writew (readw (I2C_CON) | I2C_CON_STP, I2C_CON); /* finish up xfer */
+ writew(0xFFFF, &i2c_base->stat); /* failue, clear sources*/
+ writew (readw (&i2c_base->con) | I2C_CON_STP, &i2c_base->con); /* finish up xfer */
udelay(20000);
wait_for_bb ();
}
flush_fifo();
- writew (0, I2C_CNT); /* don't allow any more data in...we don't want it.*/
- writew(0xFFFF, I2C_STAT);
+ writew (0, &i2c_base->cnt); /* don't allow any more data in...we don't want it.*/
+ writew(0xFFFF, &i2c_base->stat);
return res;
}
@@ -370,17 +377,17 @@
int timeout = 10;
u16 stat;
- writew(0xFFFF, I2C_STAT); /* clear current interruts...*/
- while ((stat = readw (I2C_STAT) & I2C_STAT_BB) && timeout--) {
- writew (stat, I2C_STAT);
+ writew(0xFFFF, &i2c_base->stat); /* clear current interruts...*/
+ while ((stat = readw (&i2c_base->stat) & I2C_STAT_BB) && timeout--) {
+ writew (stat, &i2c_base->stat);
udelay (50000);
}
if (timeout <= 0) {
printf ("timed out in wait_for_bb: I2C_STAT=%x\n",
- readw (I2C_STAT));
+ readw (&i2c_base->stat));
}
- writew(0xFFFF, I2C_STAT); /* clear delayed stuff*/
+ writew(0xFFFF, &i2c_base->stat); /* clear delayed stuff*/
}
static u16 wait_for_pin (void)
@@ -390,7 +397,7 @@
do {
udelay (1000);
- status = readw (I2C_STAT);
+ status = readw (&i2c_base->stat);
} while ( !(status &
(I2C_STAT_ROVR | I2C_STAT_XUDF | I2C_STAT_XRDY |
I2C_STAT_RRDY | I2C_STAT_ARDY | I2C_STAT_NACK |
@@ -398,8 +405,33 @@
if (timeout <= 0) {
printf ("timed out in wait_for_pin: I2C_STAT=%x\n",
- readw (I2C_STAT));
- writew(0xFFFF, I2C_STAT);
+ readw (&i2c_base->stat));
+ writew(0xFFFF, &i2c_base->stat);
}
return status;
}
+
+int i2c_set_bus_num(unsigned int bus)
+{
+ if ((bus < 0) || (bus >= I2C_BUS_MAX)) {
+ printf("Bad bus: %d\n", bus);
+ return -1;
+ }
+
+#if I2C_BUS_MAX==3
+ if (bus == 2)
+ i2c_base = (struct i2c *)I2C_BASE3;
+ else
+#endif
+ if (bus == 1)
+ i2c_base = (struct i2c *)I2C_BASE2;
+ else
+ i2c_base = (struct i2c *)I2C_BASE1;
+
+ current_bus = bus;
+
+ if(!bus_initialized[current_bus])
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+ return 0;
+}
diff --git a/include/asm-arm/arch-omap24xx/i2c.h b/include/asm-arm/arch-omap24xx/i2c.h
index 44db7a2..19046aa 100644
--- a/include/asm-arm/arch-omap24xx/i2c.h
+++ b/include/asm-arm/arch-omap24xx/i2c.h
@@ -23,24 +23,45 @@
#ifndef _OMAP24XX_I2C_H_
#define _OMAP24XX_I2C_H_
-#define I2C_BASE 0x48070000
+#define I2C_BASE1 0x48070000
#define I2C_BASE2 0x48072000 /* nothing hooked up on h4 */
-#define I2C_REV (I2C_BASE + 0x00)
-#define I2C_IE (I2C_BASE + 0x04)
-#define I2C_STAT (I2C_BASE + 0x08)
-#define I2C_IV (I2C_BASE + 0x0c)
-#define I2C_BUF (I2C_BASE + 0x14)
-#define I2C_CNT (I2C_BASE + 0x18)
-#define I2C_DATA (I2C_BASE + 0x1c)
-#define I2C_SYSC (I2C_BASE + 0x20)
-#define I2C_CON (I2C_BASE + 0x24)
-#define I2C_OA (I2C_BASE + 0x28)
-#define I2C_SA (I2C_BASE + 0x2c)
-#define I2C_PSC (I2C_BASE + 0x30)
-#define I2C_SCLL (I2C_BASE + 0x34)
-#define I2C_SCLH (I2C_BASE + 0x38)
-#define I2C_SYSTEST (I2C_BASE + 0x3c)
+#define I2C_DEFAULT_BASE I2C_BASE1
+
+struct i2c {
+ unsigned short rev; /* 0x00 */
+ unsigned short res1;
+ unsigned short ie; /* 0x04 */
+ unsigned short res2;
+ unsigned short stat; /* 0x08 */
+ unsigned short res3;
+ unsigned short iv; /* 0x0C */
+ unsigned short res4[3];
+ unsigned short buf; /* 0x14 */
+ unsigned short res5;
+ unsigned short cnt; /* 0x18 */
+ unsigned short res6;
+ unsigned short data; /* 0x1C */
+ unsigned short res7;
+ unsigned short sysc; /* 0x20 */
+ unsigned short res8;
+ unsigned short con; /* 0x24 */
+ unsigned short res9;
+ unsigned short oa; /* 0x28 */
+ unsigned short res10;
+ unsigned short sa; /* 0x2C */
+ unsigned short res11;
+ unsigned short psc; /* 0x30 */
+ unsigned short res12;
+ unsigned short scll; /* 0x34 */
+ unsigned short res13;
+ unsigned short sclh; /* 0x38 */
+ unsigned short res14;
+ unsigned short systest; /* 0x3c */
+ unsigned short res15;
+};
+
+#define I2C_BUS_MAX 2
/* I2C masks */
diff --git a/include/asm-arm/arch-omap3/i2c.h b/include/asm-arm/arch-omap3/i2c.h
index 8b339cc..490e03b 100644
--- a/include/asm-arm/arch-omap3/i2c.h
+++ b/include/asm-arm/arch-omap3/i2c.h
@@ -25,21 +25,40 @@
#define I2C_DEFAULT_BASE I2C_BASE1
-#define I2C_REV (I2C_DEFAULT_BASE + 0x00)
-#define I2C_IE (I2C_DEFAULT_BASE + 0x04)
-#define I2C_STAT (I2C_DEFAULT_BASE + 0x08)
-#define I2C_IV (I2C_DEFAULT_BASE + 0x0c)
-#define I2C_BUF (I2C_DEFAULT_BASE + 0x14)
-#define I2C_CNT (I2C_DEFAULT_BASE + 0x18)
-#define I2C_DATA (I2C_DEFAULT_BASE + 0x1c)
-#define I2C_SYSC (I2C_DEFAULT_BASE + 0x20)
-#define I2C_CON (I2C_DEFAULT_BASE + 0x24)
-#define I2C_OA (I2C_DEFAULT_BASE + 0x28)
-#define I2C_SA (I2C_DEFAULT_BASE + 0x2c)
-#define I2C_PSC (I2C_DEFAULT_BASE + 0x30)
-#define I2C_SCLL (I2C_DEFAULT_BASE + 0x34)
-#define I2C_SCLH (I2C_DEFAULT_BASE + 0x38)
-#define I2C_SYSTEST (I2C_DEFAULT_BASE + 0x3c)
+struct i2c {
+ unsigned short rev; /* 0x00 */
+ unsigned short res1;
+ unsigned short ie; /* 0x04 */
+ unsigned short res2;
+ unsigned short stat; /* 0x08 */
+ unsigned short res3;
+ unsigned short iv; /* 0x0C */
+ unsigned short res4[3];
+ unsigned short buf; /* 0x14 */
+ unsigned short res5;
+ unsigned short cnt; /* 0x18 */
+ unsigned short res6;
+ unsigned short data; /* 0x1C */
+ unsigned short res7;
+ unsigned short sysc; /* 0x20 */
+ unsigned short res8;
+ unsigned short con; /* 0x24 */
+ unsigned short res9;
+ unsigned short oa; /* 0x28 */
+ unsigned short res10;
+ unsigned short sa; /* 0x2C */
+ unsigned short res11;
+ unsigned short psc; /* 0x30 */
+ unsigned short res12;
+ unsigned short scll; /* 0x34 */
+ unsigned short res13;
+ unsigned short sclh; /* 0x38 */
+ unsigned short res14;
+ unsigned short systest; /* 0x3c */
+ unsigned short res15;
+};
+
+#define I2C_BUS_MAX 3
/* I2C masks */
diff --git a/include/asm-ppc/4xx_pci.h b/include/asm-ppc/4xx_pci.h
index 30125a1..f686e7c 100644
--- a/include/asm-ppc/4xx_pci.h
+++ b/include/asm-ppc/4xx_pci.h
@@ -1,6 +1,8 @@
#ifndef _405GP_PCI_H
#define _405GP_PCI_H
+#include <pci.h>
+
/*----------------------------------------------------------------------------+
| 405GP PCI core memory map defines.
+----------------------------------------------------------------------------*/
@@ -49,4 +51,10 @@
#define PCIDEVID_405GP 0x0
+void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev);
+int pci_arbiter_enabled(void);
+int __pci_pre_init(struct pci_controller *hose);
+void __pci_target_init(struct pci_controller *hose);
+void __pci_master_init(struct pci_controller *hose);
+
#endif
diff --git a/include/configs/DU440.h b/include/configs/DU440.h
index e9ea1bf..65dc235 100644
--- a/include/configs/DU440.h
+++ b/include/configs/DU440.h
@@ -60,8 +60,9 @@
#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
-#define CONFIG_SYS_PCI_IOBASE 0xe8000000
-
+#define CONFIG_SYS_PCI_IOBASE 0xe8000000
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH
+#define CONFIG_SYS_PCI_SUBSYS_ID 0x0444 /* device ID for DU440 */
/* Don't change either of these */
#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h
index d6e2f6b..6310cfc 100644
--- a/include/configs/PMC440.h
+++ b/include/configs/PMC440.h
@@ -351,7 +351,6 @@
#define CONFIG_CMD_BSP
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
#define CONFIG_CMD_DIAG
@@ -359,7 +358,6 @@
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NET
@@ -435,11 +433,14 @@
/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT
#define CONFIG_SYS_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ
/* PCI identification */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */
#define CONFIG_SYS_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */
+/* for weak __pci_target_init() */
+#define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_ID_MONARCH
#define CONFIG_SYS_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC
#define CONFIG_SYS_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST
diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index e6248e9..964630f 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -231,13 +231,11 @@
*/
#include <config_cmd_default.h>
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_FPGA
#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NET
diff --git a/include/configs/korat.h b/include/configs/korat.h
index ea6ba89..026dd08 100644
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -69,6 +69,7 @@
#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE
#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE + 0x20000000)
/* Don't change either of these */
#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
@@ -359,6 +360,7 @@
/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT
#define CONFIG_SYS_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 9605ce2..5788d58 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -364,6 +364,7 @@
/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT
#define CONFIG_SYS_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
diff --git a/include/ppc440.h b/include/ppc440.h
index e54a977..a050ffd 100644
--- a/include/ppc440.h
+++ b/include/ppc440.h
@@ -1276,7 +1276,8 @@
#define CPC0_STRP1_PAE_MASK (0x80000000 >> 11)
#define CPC0_STRP1_PISE_MASK (0x80000000 >> 13)
#endif /* defined(CONFIG_440GP) */
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
#define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 13)
#define SDR0_SDSTP1_PISE_MASK (0x80000000 >> 15)
#endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */
