doc/man/man5/knl.conf.5 - SchedMD/slurm - Git at Google

 .TH "knl.conf" "5" "Slurm Configuration File" "December 2022" "Slurm Configuration File"

 .SH "NAME"
 knl.conf \- Slurm configuration file for Intel Knights Landing processor.

 .SH "DESCRIPTION"
 This ASCII file which describes configuration information for Intel Knights
 Landing processors and its name may depend upon the NodeFeatures plugin
 configured in Slurm. For example, on Cray systems NodeFeatures should be configured
 to "knl_cray" and its configuration file will be read from "knl_cray.conf".
 The file will always be located in the same directory as the \fBslurm.conf\fR.
 This file is optional.
 .LP
 Parameter names are case insensitive.
 Any text following a "#" in the configuration file is treated
 as a comment through the end of that line.
 Changes to the configuration file take effect upon restart of
 Slurm daemons, daemon receipt of the SIGHUP signal, or execution
 of the command "scontrol reconfigure" unless otherwise noted.
 .LP
 The overall configuration parameters available include:

 .TP
 \fBAllowMCDRAM\fR
 Specify the MCDRAM modes which jobs are allowed to use.
 This may be a subset of MCDRAM modes supported by the node.
 If not specified, all MCDRAM modes supported by the node are available for use.
 The comma separated list of allowed MCDRAM modes may include any of the modes
 listed below.
 .IP
 .RS
 .TP 17
 \fBcache\fR
 All of MCDRAM to be used as cache.
 .IP

 .TP
 \fBequal\fR
 MCDRAM to be used partly as cache and partly combined with primary memory.
 .IP

 .TP
 \fBflat\fR
 MCDRAM to be combined with primary memory into a "flat" memory space.
 .RE
 .IP

 .TP
 \fBAllowNUMA\fR
 Specify the NUMA modes which jobs are allowed to use.
 This may be a subset of NUMA modes supported by the node.
 If not specified, all NUMA modes supported by the node are available for use.
 The comma separated list of allowed NUMA modes may include any of the modes
 listed below.
 Note that Slurm can only support homogeneous nodes
 (e.g. the same number of cores per NUMA node).
 KNL scn4 and quad modes are not homogeneous, but each NUMA mode will have
 either 16 or 18 cores.
 This will result in Slurm using the lower core count and finding a total of
 256 threads rather than 272 threads and setting the node to a DOWN state.
 Therefore it is recommended that snc4 and quad mode not be allowed at this time.
 .IP
 .RS
 .TP 17
 \fBa2a\fR
 All to all
 .IP

 .TP
 \fBsnc2\fR
 Sub\-NUMA cluster 2
 .IP

 .TP
 \fBsnc4\fR
 Sub\-NUMA cluster 4
 .IP

 .TP
 \fBhemi\fR
 Hemisphere
 .IP

 .TP
 \fBquad\fR
 Quadrant
 .RE
 .IP

 .TP
 \fBAllowUserBoot\fR
 A comma\-delimited list of users allowed to modify a node's MCDRAM or NUMA state.
 If not specified then any user can change a node's state and reboot it.
 .IP

 .TP
 \fBBootTime\fR
 Estimated time to reboot a node in seconds.
 Used as a basis for optimizing scheduling decisions.
 The default value is 300 seconds (5 minutes) for the "knl_generic" plugin
 and 2700 seconds (45 minutes) for the "knl_cray" plugin.
 .IP

 .TP
 \fBCapmcPath\fR
 Fully qualified path to the \fBcapmc\fR program.
 The default value is "/opt/cray/capmc/default/bin/capmc".
 This parameter is used only by the "knl_cray" plugin.
 .IP

 .TP
 \fBCapmcPollFreq\fR
 Time interval between when the \fBcapmc\fR program should poll for node state
 changes, in seconds.
 The default value is 45 seconds.
 This parameter is used only by the "knl_cray" plugin.
 .IP

 .TP
 \fBCapmcRetries\fR
 Number of times to retry failed operations of the \fBcapmc\fR program.
 Default value is 4.
 .IP

 .TP
 \fBCapmcTimeout\fR
 Time limit for the \fBcapmc\fR program to return status information milliseconds.
 The default value is 60000 milliseconds and the minimum value is 1000 milliseconds.
 This parameter is used by the "knl_cray" plugin, plus the capmc_suspend and
 capmc_resume programs used for suspending and resuming nodes.
 .IP

 .TP
 \fBCnselectPath\fR
 Fully qualified path to the \fBcnselect\fR program.
 The default value is "/opt/cray/sdb/default/bin/cnselect".
 This parameter is used only by the "knl_cray" plugin.
 .IP

 .TP
 \fBDefaultMCDRAM\fR
 Specify the default MCDRAM modes for job's which do not specify a value.
 This is only used when a node is booted and the job which has been allocated
 the node does not specify a desired MCDRAM mode.
 The value can include one of the possible values identified with the
 \fBAllowMCDRAM\fR configuration parameter above.
 The default value is "cache".
 .IP

 .TP
 \fBDefaultNUMA\fR
 Specify the default NUMA modes for job's which do not specify a value.
 This is only used when a node is booted and the job which has been allocated
 the node does not specify a desired NUMA mode.
 The value can include one of the possible values identified with the
 \fBAllowNUMA\fR configuration parameter above.
 The default value is "a2a".
 .IP

 .TP
 \fBForce\fR
 If set to a non\-zero value then load the node_features/generic plugin even
 on non\-KNL nodes.
 Used primarily for testing purposes.
 .IP

 .TP
 \fBLogFile\fR
 Fully qualified path to a log file.
 The default value is SlurmctldLogFile from the slurm.conf configuration file.
 This is option is used only by the campc_suspend and campc_resume programs
 (which power down and reboot nodes in the appropriate configuration).
 .IP

 .TP
 \fBMcPath\fR
 Fully qualified path to memory controller device file directory.
 Children of this directory with names of the form "mc#/csrow#/ue_count"
 (i.e. the count of unrecoverable memory errors) will be monitored for non\-zero
 values.
 If such errors are detected, the node will be set to a DOWN state and the
 slurmd daemon will shutdown.
 The default value is "/sys/devices/system/edac/mc".
 See also \fBUmeCheckInterval\fR.
 .IP

 .TP
 \fBNumaCpuBind\fR
 Contains pairs of NUMA modes and the CpuBind mode to set a node to for that mode.
 Any compute node found with or set to the specified NUMA mode will have that
 node's CpuBind field set to the configured value.
 The NUMA node will be followed by an equal sign the desired CpuBind mode for
 that NUMA mode. Multiple NUMA mode and CpuBind modes should be in a semicolon
 separated list.
 By default changes to a node's NUMA mode will not effect that node's CpuBind
 mode.
 See the example below.
 .IP

 .TP
 \fBSyscfgPath\fR
 Fully qualified path to Intel's \fBsyscfg\fR program, which identifies current
 KNL configuration by viewing BIOS settings.
 If not defined, the current BIOS setting will not be available.
 The default value is "/usr/bin/syscfg".
 This parameter is used only by the "knl_generic" plugin.
 .IP

 .TP
 \fBSyscfgTimeout\fR
 Timeout for \fBsyscfg\fR program in milliseconds.
 Default value is 1000 milliseconds.
 For Dell KNL systems, experience has shown that a higher value of 10000
 milliseconds is more appropriate.
 .IP

 .TP
 \fBSystemType\fR
 Used to distinguish the flavor of knl we are dealing with.
 Possible options are "Dell" and "Intel".
 The default value is "Intel".
 This parameter is used only by the "knl_generic" plugin.
 .IP

 .TP
 \fBUmeCheckInterval\fR
 Interval, in microseconds, between checks for Uncorrectable Memory Errors (UME).
 If such errors are detected, the node will be set to a DOWN state and the
 slurmd daemon will shutdown.
 The default value is 0 (disabled).
 See also \fBMcPath\fR.
 .IP

 .TP
 \fBValidateMode\fR
 If set to 1 then validate, but do not modify the node's configured MCDRAM and
 NUMA modes from the slurm.conf file. If the actual modes do not match configured
 values the node will be set to a DOWN state. Every KNL nodes MCDRAM and NUMA
 states must both be listed in the slurm.conf file.
 This parameter is used only by the "knl_cray" plugin.
 .IP

 .SH "EXAMPLE"
 .nf
 ###################################################################
 # knl_cray.conf
 # Slurm configuration file for Intel Knights Landing on Cray system
 ###################################################################
 CapmcPath=/opt/cray/capmc/default/bin/capmc
 CapmcTimeout=6000
 DefaultMCDRAM=flat
 DefaultNUMA=a2a
 NumaCpuBind=a2a=core;snc2=thread;snc4=thread
 LogFile=/var/tmp/slurm_node_feature.log
 SyscfgPath=/usr/sbin/syscfg
 .fi

 .SH "COPYING"
 Copyright (C) 2015\-2022 SchedMD LLC.
 .LP
 This file is part of Slurm, a resource management program.
 For details, see <https://slurm.schedmd.com/>.
 .LP
 Slurm is free software; you can redistribute it and/or modify it under
 the terms of the GNU General Public License as published by the Free
 Software Foundation; either version 2 of the License, or (at your option)
 any later version.
 .LP
 Slurm is distributed in the hope that it will be useful, but WITHOUT ANY
 WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
 FOR A PARTICULAR PURPOSE. See the GNU General Public License for more
 details.

 .SH "SEE ALSO"
 .LP
 \fBslurm.conf\fR(5)
	.TH "knl.conf" "5" "Slurm Configuration File" "December 2022" "Slurm Configuration File"

	.SH "NAME"
	knl.conf \- Slurm configuration file for Intel Knights Landing processor.

	.SH "DESCRIPTION"
	This ASCII file which describes configuration information for Intel Knights
	Landing processors and its name may depend upon the NodeFeatures plugin
	configured in Slurm. For example, on Cray systems NodeFeatures should be configured
	to "knl_cray" and its configuration file will be read from "knl_cray.conf".
	The file will always be located in the same directory as the \fBslurm.conf\fR.
	This file is optional.
	.LP
	Parameter names are case insensitive.
	Any text following a "#" in the configuration file is treated
	as a comment through the end of that line.
	Changes to the configuration file take effect upon restart of
	Slurm daemons, daemon receipt of the SIGHUP signal, or execution
	of the command "scontrol reconfigure" unless otherwise noted.
	.LP
	The overall configuration parameters available include:

	.TP
	\fBAllowMCDRAM\fR
	Specify the MCDRAM modes which jobs are allowed to use.
	This may be a subset of MCDRAM modes supported by the node.
	If not specified, all MCDRAM modes supported by the node are available for use.
	The comma separated list of allowed MCDRAM modes may include any of the modes
	listed below.
	.IP
	.RS
	.TP 17
	\fBcache\fR
	All of MCDRAM to be used as cache.
	.IP

	.TP
	\fBequal\fR
	MCDRAM to be used partly as cache and partly combined with primary memory.
	.IP

	.TP
	\fBflat\fR
	MCDRAM to be combined with primary memory into a "flat" memory space.
	.RE
	.IP

	.TP
	\fBAllowNUMA\fR
	Specify the NUMA modes which jobs are allowed to use.
	This may be a subset of NUMA modes supported by the node.
	If not specified, all NUMA modes supported by the node are available for use.
	The comma separated list of allowed NUMA modes may include any of the modes
	listed below.
	Note that Slurm can only support homogeneous nodes
	(e.g. the same number of cores per NUMA node).
	KNL scn4 and quad modes are not homogeneous, but each NUMA mode will have
	either 16 or 18 cores.
	This will result in Slurm using the lower core count and finding a total of
	256 threads rather than 272 threads and setting the node to a DOWN state.
	Therefore it is recommended that snc4 and quad mode not be allowed at this time.
	.IP
	.RS
	.TP 17
	\fBa2a\fR
	All to all
	.IP

	.TP
	\fBsnc2\fR
	Sub\-NUMA cluster 2
	.IP

	.TP
	\fBsnc4\fR
	Sub\-NUMA cluster 4
	.IP

	.TP
	\fBhemi\fR
	Hemisphere
	.IP

	.TP
	\fBquad\fR
	Quadrant
	.RE
	.IP

	.TP
	\fBAllowUserBoot\fR
	A comma\-delimited list of users allowed to modify a node's MCDRAM or NUMA state.
	If not specified then any user can change a node's state and reboot it.
	.IP

	.TP
	\fBBootTime\fR
	Estimated time to reboot a node in seconds.
	Used as a basis for optimizing scheduling decisions.
	The default value is 300 seconds (5 minutes) for the "knl_generic" plugin
	and 2700 seconds (45 minutes) for the "knl_cray" plugin.
	.IP

	.TP
	\fBCapmcPath\fR
	Fully qualified path to the \fBcapmc\fR program.
	The default value is "/opt/cray/capmc/default/bin/capmc".
	This parameter is used only by the "knl_cray" plugin.
	.IP

	.TP
	\fBCapmcPollFreq\fR
	Time interval between when the \fBcapmc\fR program should poll for node state
	changes, in seconds.
	The default value is 45 seconds.
	This parameter is used only by the "knl_cray" plugin.
	.IP

	.TP
	\fBCapmcRetries\fR
	Number of times to retry failed operations of the \fBcapmc\fR program.
	Default value is 4.
	.IP

	.TP
	\fBCapmcTimeout\fR
	Time limit for the \fBcapmc\fR program to return status information milliseconds.
	The default value is 60000 milliseconds and the minimum value is 1000 milliseconds.
	This parameter is used by the "knl_cray" plugin, plus the capmc_suspend and
	capmc_resume programs used for suspending and resuming nodes.
	.IP

	.TP
	\fBCnselectPath\fR
	Fully qualified path to the \fBcnselect\fR program.
	The default value is "/opt/cray/sdb/default/bin/cnselect".
	This parameter is used only by the "knl_cray" plugin.
	.IP

	.TP
	\fBDefaultMCDRAM\fR
	Specify the default MCDRAM modes for job's which do not specify a value.
	This is only used when a node is booted and the job which has been allocated
	the node does not specify a desired MCDRAM mode.
	The value can include one of the possible values identified with the
	\fBAllowMCDRAM\fR configuration parameter above.
	The default value is "cache".
	.IP

	.TP
	\fBDefaultNUMA\fR
	Specify the default NUMA modes for job's which do not specify a value.
	This is only used when a node is booted and the job which has been allocated
	the node does not specify a desired NUMA mode.
	The value can include one of the possible values identified with the
	\fBAllowNUMA\fR configuration parameter above.
	The default value is "a2a".
	.IP

	.TP
	\fBForce\fR
	If set to a non\-zero value then load the node_features/generic plugin even
	on non\-KNL nodes.
	Used primarily for testing purposes.
	.IP

	.TP
	\fBLogFile\fR
	Fully qualified path to a log file.
	The default value is SlurmctldLogFile from the slurm.conf configuration file.
	This is option is used only by the campc_suspend and campc_resume programs
	(which power down and reboot nodes in the appropriate configuration).
	.IP

	.TP
	\fBMcPath\fR
	Fully qualified path to memory controller device file directory.
	Children of this directory with names of the form "mc#/csrow#/ue_count"
	(i.e. the count of unrecoverable memory errors) will be monitored for non\-zero
	values.
	If such errors are detected, the node will be set to a DOWN state and the
	slurmd daemon will shutdown.
	The default value is "/sys/devices/system/edac/mc".
	See also \fBUmeCheckInterval\fR.
	.IP

	.TP
	\fBNumaCpuBind\fR
	Contains pairs of NUMA modes and the CpuBind mode to set a node to for that mode.
	Any compute node found with or set to the specified NUMA mode will have that
	node's CpuBind field set to the configured value.
	The NUMA node will be followed by an equal sign the desired CpuBind mode for
	that NUMA mode. Multiple NUMA mode and CpuBind modes should be in a semicolon
	separated list.
	By default changes to a node's NUMA mode will not effect that node's CpuBind
	mode.
	See the example below.
	.IP

	.TP
	\fBSyscfgPath\fR
	Fully qualified path to Intel's \fBsyscfg\fR program, which identifies current
	KNL configuration by viewing BIOS settings.
	If not defined, the current BIOS setting will not be available.
	The default value is "/usr/bin/syscfg".
	This parameter is used only by the "knl_generic" plugin.
	.IP

	.TP
	\fBSyscfgTimeout\fR
	Timeout for \fBsyscfg\fR program in milliseconds.
	Default value is 1000 milliseconds.
	For Dell KNL systems, experience has shown that a higher value of 10000
	milliseconds is more appropriate.
	.IP

	.TP
	\fBSystemType\fR
	Used to distinguish the flavor of knl we are dealing with.
	Possible options are "Dell" and "Intel".
	The default value is "Intel".
	This parameter is used only by the "knl_generic" plugin.
	.IP

	.TP
	\fBUmeCheckInterval\fR
	Interval, in microseconds, between checks for Uncorrectable Memory Errors (UME).
	If such errors are detected, the node will be set to a DOWN state and the
	slurmd daemon will shutdown.
	The default value is 0 (disabled).
	See also \fBMcPath\fR.
	.IP

	.TP
	\fBValidateMode\fR
	If set to 1 then validate, but do not modify the node's configured MCDRAM and
	NUMA modes from the slurm.conf file. If the actual modes do not match configured
	values the node will be set to a DOWN state. Every KNL nodes MCDRAM and NUMA
	states must both be listed in the slurm.conf file.
	This parameter is used only by the "knl_cray" plugin.
	.IP

	.SH "EXAMPLE"
	.nf
	###################################################################
	# knl_cray.conf
	# Slurm configuration file for Intel Knights Landing on Cray system
	###################################################################
	CapmcPath=/opt/cray/capmc/default/bin/capmc
	CapmcTimeout=6000
	DefaultMCDRAM=flat
	DefaultNUMA=a2a
	NumaCpuBind=a2a=core;snc2=thread;snc4=thread
	LogFile=/var/tmp/slurm_node_feature.log
	SyscfgPath=/usr/sbin/syscfg
	.fi

	.SH "COPYING"
	Copyright (C) 2015\-2022 SchedMD LLC.
	.LP
	This file is part of Slurm, a resource management program.
	For details, see <https://slurm.schedmd.com/>.
	.LP
	Slurm is free software; you can redistribute it and/or modify it under
	the terms of the GNU General Public License as published by the Free
	Software Foundation; either version 2 of the License, or (at your option)
	any later version.
	.LP
	Slurm is distributed in the hope that it will be useful, but WITHOUT ANY
	WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
	FOR A PARTICULAR PURPOSE. See the GNU General Public License for more
	details.

	.SH "SEE ALSO"
	.LP
	\fBslurm.conf\fR(5)