| /* | |
| * (C) Copyright 2001 | |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. | |
| * | |
| * See file CREDITS for list of people who contributed to this | |
| * project. | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License as | |
| * published by the Free Software Foundation; either version 2 of | |
| * the License, or (at your option) any later version. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| * You should have received a copy of the GNU General Public License | |
| * along with this program; if not, write to the Free Software | |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, | |
| * MA 02111-1307 USA | |
| */ | |
| /* | |
| * | |
| * Configuration settings for the CU824 board. | |
| * | |
| */ | |
| /* ------------------------------------------------------------------------- */ | |
| /* | |
| * board/config.h - configuration options, board specific | |
| */ | |
| #ifndef __CONFIG_H | |
| #define __CONFIG_H | |
| /* | |
| * High Level Configuration Options | |
| * (easy to change) | |
| */ | |
| #define CONFIG_MPC824X 1 | |
| #define CONFIG_MPC8245 1 | |
| #define CONFIG_BMW 1 | |
| #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ | |
| #define CONFIG_BCM570x 1 /* Use Broadcom BCM570x Ethernet Driver */ | |
| #define CONFIG_TIGON3 1 | |
| #define CONFIG_CONS_INDEX 1 | |
| #define CONFIG_BAUDRATE 9600 | |
| #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } | |
| #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ | |
| #define CONFIG_BOOTCOMMAND "bootm FF820000" /* autoboot command */ | |
| #define CONFIG_BOOTDELAY 5 | |
| #define CFG_MAX_DOC_DEVICE 1 /* Only use Onboard TSOP-16MB device */ | |
| #define DOC_PASSIVE_PROBE 1 | |
| #define CFG_DOC_SUPPORT_2000 1 | |
| #define CFG_DOC_SUPPORT_MILLENNIUM 1 | |
| #define CFG_DOC_SHORT_TIMEOUT 1 | |
| #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ | |
| CFG_CMD_DATE | \ | |
| CFG_CMD_DOC | \ | |
| CFG_CMD_ELF | \ | |
| 0 ) | |
| #if 0 | |
| #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP | \ | |
| CFG_CMD_PCI | CFG_CMD_DOC | CFG_CMD_DATE) | |
| #define CONFIG_PCI 1 | |
| #define CONFIG_PCI_PNP 1 /* PCI plug-and-play */ | |
| #endif | |
| /* This must be included AFTER the definition of CONFIG_COMMANDS (if any) | |
| */ | |
| #include <cmd_confdefs.h> | |
| /* | |
| * Miscellaneous configurable options | |
| */ | |
| #define CFG_LONGHELP /* undef to save memory */ | |
| #define CFG_PROMPT "=>" /* Monitor Command Prompt */ | |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ | |
| /* Print Buffer Size | |
| */ | |
| #define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) | |
| #define CFG_MAXARGS 8 /* Max number of command args */ | |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ | |
| #define CFG_LOAD_ADDR 0x00100000 /* Default load address */ | |
| /*----------------------------------------------------------------------- | |
| * Start addresses for the final memory configuration | |
| * (Set up by the startup code) | |
| * Please note that CFG_SDRAM_BASE _must_ start at 0 | |
| */ | |
| #define CFG_SDRAM_BASE 0x00000000 | |
| #define CFG_FLASH_BASE0_PRELIM 0xFFF00000 /* FLASH bank on RCS#0 */ | |
| #define CFG_FLASH_BASE1_PRELIM 0xFF800000 /* FLASH bank on RCS#1 */ | |
| #define CFG_FLASH_BASE CFG_MONITOR_BASE | |
| #define CFG_FLASH_BANKS { CFG_FLASH_BASE0_PRELIM , CFG_FLASH_BASE1_PRELIM } | |
| /* even though FLASHP_BASE is FF800000, with 4MB is RCS0, the | |
| * reset vector is actually located at FFB00100, but the 8245 | |
| * takes care of us. | |
| */ | |
| #define CFG_RESET_ADDRESS 0xFFF00100 | |
| #define CFG_EUMB_ADDR 0xFC000000 | |
| #define CFG_MONITOR_BASE TEXT_BASE | |
| #define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ | |
| #define CFG_MALLOC_LEN (2048 << 10) /* Reserve 2MB for malloc() */ | |
| #define CFG_MEMTEST_START 0x00004000 /* memtest works on */ | |
| #define CFG_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */ | |
| /* Maximum amount of RAM. | |
| */ | |
| #define CFG_MAX_RAM_SIZE 0x04000000 /* 0 .. 64 MB of (S)DRAM */ | |
| #if CFG_MONITOR_BASE >= CFG_FLASH_BASE | |
| #undef CFG_RAMBOOT | |
| #else | |
| #define CFG_RAMBOOT | |
| #endif | |
| /*----------------------------------------------------------------------- | |
| * Definitions for initial stack pointer and data area | |
| */ | |
| #define CFG_INIT_RAM_ADDR CFG_SDRAM_BASE + CFG_MONITOR_LEN | |
| #define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ | |
| #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ | |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) | |
| #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET | |
| /* | |
| * Low Level Configuration Settings | |
| * (address mappings, register initial values, etc.) | |
| * You should know what you are doing if you make changes here. | |
| * For the detail description refer to the MPC8240 user's manual. | |
| */ | |
| #define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ | |
| #define CFG_HZ 1000 | |
| #define CFG_ETH_DEV_FN 0x7800 | |
| #define CFG_ETH_IOBASE 0x00104000 | |
| /* Bit-field values for MCCR1. | |
| */ | |
| #define CFG_ROMNAL 0xf | |
| #define CFG_ROMFAL 0x1f | |
| #define CFG_DBUS_SIZE 0x3 | |
| /* Bit-field values for MCCR2. | |
| */ | |
| #define CFG_TSWAIT 0x5 /* Transaction Start Wait States timer */ | |
| #define CFG_REFINT 0x400 /* Refresh interval FIXME: was 0t430 */ | |
| /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. | |
| */ | |
| #define CFG_BSTOPRE 0 /* FIXME: was 192 */ | |
| /* Bit-field values for MCCR3. | |
| */ | |
| #define CFG_REFREC 2 /* Refresh to activate interval */ | |
| /* Bit-field values for MCCR4. | |
| */ | |
| #define CFG_PRETOACT 2 /* Precharge to activate interval FIXME: was 2 */ | |
| #define CFG_ACTTOPRE 5 /* Activate to Precharge interval FIXME: was 5 */ | |
| #define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */ | |
| #define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */ | |
| #define CFG_SDMODE_BURSTLEN 3 /* SDMODE Burst length */ | |
| #define CFG_ACTORW 0xa /* FIXME was 2 */ | |
| #define CFG_REGISTERD_TYPE_BUFFER 1 | |
| #define CFG_PGMAX 0x0 /* how long the 8240 reatins the currently accessed page in memory FIXME: was 0x32*/ | |
| #define CFG_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay - note bottom 3 bits MUST be 0 */ | |
| /* Memory bank settings. | |
| * Only bits 20-29 are actually used from these vales to set the | |
| * start/end addresses. The upper two bits will always be 0, and the lower | |
| * 20 bits will be 0x00000 for a start address, or 0xfffff for an end | |
| * address. Refer to the MPC8240 book. | |
| */ | |
| #define CFG_BANK0_START 0x00000000 | |
| #define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1) | |
| #define CFG_BANK0_ENABLE 1 | |
| #define CFG_BANK1_START 0x3ff00000 | |
| #define CFG_BANK1_END 0x3fffffff | |
| #define CFG_BANK1_ENABLE 0 | |
| #define CFG_BANK2_START 0x3ff00000 | |
| #define CFG_BANK2_END 0x3fffffff | |
| #define CFG_BANK2_ENABLE 0 | |
| #define CFG_BANK3_START 0x3ff00000 | |
| #define CFG_BANK3_END 0x3fffffff | |
| #define CFG_BANK3_ENABLE 0 | |
| #define CFG_BANK4_START 0x3ff00000 | |
| #define CFG_BANK4_END 0x3fffffff | |
| #define CFG_BANK4_ENABLE 0 | |
| #define CFG_BANK5_START 0x3ff00000 | |
| #define CFG_BANK5_END 0x3fffffff | |
| #define CFG_BANK5_ENABLE 0 | |
| #define CFG_BANK6_START 0x3ff00000 | |
| #define CFG_BANK6_END 0x3fffffff | |
| #define CFG_BANK6_ENABLE 0 | |
| #define CFG_BANK7_START 0x3ff00000 | |
| #define CFG_BANK7_END 0x3fffffff | |
| #define CFG_BANK7_ENABLE 0 | |
| #define CFG_ODCR 0xff | |
| #define CONFIG_PCI 1 /* Include PCI support */ | |
| #undef CONFIG_PCI_PNP | |
| /* PCI Memory space(s) */ | |
| #define PCI_MEM_SPACE1_START 0x80000000 | |
| #define PCI_MEM_SPACE2_START 0xfd000000 | |
| /* ROM Spaces */ | |
| #include "../board/bmw/bmw.h" | |
| /* BAT configuration */ | |
| #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) | |
| #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) | |
| #define CFG_IBAT1L (0x70000000 | BATL_PP_10 | BATL_CACHEINHIBIT) | |
| #define CFG_IBAT1U (0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP) | |
| #define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) | |
| #define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) | |
| #define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) | |
| #define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) | |
| #define CFG_DBAT0L CFG_IBAT0L | |
| #define CFG_DBAT0U CFG_IBAT0U | |
| #define CFG_DBAT1L CFG_IBAT1L | |
| #define CFG_DBAT1U CFG_IBAT1U | |
| #define CFG_DBAT2L CFG_IBAT2L | |
| #define CFG_DBAT2U CFG_IBAT2U | |
| #define CFG_DBAT3L CFG_IBAT3L | |
| #define CFG_DBAT3U CFG_IBAT3U | |
| /* | |
| * For booting Linux, the board info and command line data | |
| * have to be in the first 8 MB of memory, since this is | |
| * the maximum mapped by the Linux kernel during initialization. | |
| */ | |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ | |
| /* | |
| * FLASH organization | |
| */ | |
| #define CFG_MAX_FLASH_BANKS 0 /* Max number of flash banks */ | |
| #define CFG_MAX_FLASH_SECT 64 /* Max number of sectors per flash */ | |
| #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ | |
| #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ | |
| /* | |
| * Warining: environment is not EMBEDDED in the U-Boot code. | |
| * It's stored in flash separately. | |
| */ | |
| #define CFG_ENV_IS_IN_NVRAM 1 | |
| #define CONFIG_ENV_OVERWRITE 1 | |
| #define CFG_NVRAM_ACCESS_ROUTINE 1 | |
| #define CFG_ENV_ADDR 0x7c004000 /* right at the start of NVRAM */ | |
| #define CFG_ENV_SIZE 0x1ff0 /* Size of the Environment - 8K */ | |
| #define CFG_ENV_OFFSET 0 /* starting right at the beginning */ | |
| /* | |
| * Cache Configuration | |
| */ | |
| #define CFG_CACHELINE_SIZE 32 | |
| #if (CONFIG_COMMANDS & CFG_CMD_KGDB) | |
| # define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ | |
| #endif | |
| /* | |
| * Internal Definitions | |
| * | |
| * Boot Flags | |
| */ | |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ | |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ | |
| #endif /* __CONFIG_H */ |