|  | /************************************************************************** | 
|  | Etherboot -  BOOTP/TFTP Bootstrap Program | 
|  | Skeleton NIC driver for Etherboot | 
|  | ***************************************************************************/ | 
|  |  | 
|  | /* | 
|  | * This program is free software; you can redistribute it and/or | 
|  | * modify it under the terms of the GNU General Public License as | 
|  | * published by the Free Software Foundation; either version 2, or (at | 
|  | * your option) any later version. | 
|  | */ | 
|  |  | 
|  | /* | 
|  | * This file is a modified version from the Galileo polled mode | 
|  | * network driver for the ethernet contained within the GT64260 | 
|  | * chip. It has been modified to fit into the U-Boot framework, from | 
|  | * the original (etherboot) setup.  Also, additional cleanup and features | 
|  | * were added. | 
|  | * | 
|  | * - Josh Huber <huber@mclx.com> | 
|  | */ | 
|  |  | 
|  | #include <common.h> | 
|  | #include <malloc.h> | 
|  | #include <galileo/gt64260R.h> | 
|  | #include <galileo/core.h> | 
|  | #include <asm/cache.h> | 
|  | #include <miiphy.h> | 
|  | #include <net.h> | 
|  | #include <netdev.h> | 
|  |  | 
|  | #include "eth.h" | 
|  | #include "eth_addrtbl.h" | 
|  |  | 
|  | #if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) | 
|  |  | 
|  | #define GT6426x_ETH_BUF_SIZE	1536 | 
|  |  | 
|  | /* if you like verbose output, turn this on! */ | 
|  | #undef DEBUG | 
|  |  | 
|  | /* Restart autoneg if we detect link is up on phy init. */ | 
|  |  | 
|  | /* | 
|  | * The GT doc's say that after Rst is deasserted, and the PHY | 
|  | * reports autoneg complete, it runs through its autoneg | 
|  | * procedures. This doesn't seem to be the case for MII | 
|  | * PHY's. To work around this check for link up && autoneg | 
|  | * complete when initilizing the port. If they are both set, | 
|  | * then restart PHY autoneg. Of course, it may be something | 
|  | * completly different. | 
|  | */ | 
|  | #ifdef CONFIG_ETHER_PORT_MII | 
|  | # define RESTART_AUTONEG | 
|  | #endif | 
|  |  | 
|  | /* do this if you dont want to use snooping */ | 
|  | #define USE_SOFTWARE_CACHE_MANAGEMENT | 
|  |  | 
|  | #ifdef USE_SOFTWARE_CACHE_MANAGEMENT | 
|  | #define FLUSH_DCACHE(a,b)                if(dcache_status()){clean_dcache_range((u32)(a),(u32)(b));} | 
|  | #define FLUSH_AND_INVALIDATE_DCACHE(a,b) if(dcache_status()){flush_dcache_range((u32)(a),(u32)(b));} | 
|  | #define INVALIDATE_DCACHE(a,b)           if(dcache_status()){invalidate_dcache_range((u32)(a),(u32)(b));} | 
|  | #else | 
|  | /* bummer - w/o flush, nothing works, even with snooping - FIXME */ | 
|  | /* #define FLUSH_DCACHE(a,b) */ | 
|  | #define FLUSH_DCACHE(a,b)                if(dcache_status()){clean_dcache_range((u32)(a),(u32)(b));} | 
|  | #define FLUSH_AND_INVALIDATE_DCACHE(a,b) | 
|  | #define INVALIDATE_DCACHE(a,b) | 
|  | #endif | 
|  | struct eth_dev_s { | 
|  | eth0_tx_desc_single *eth_tx_desc; | 
|  | eth0_rx_desc_single *eth_rx_desc; | 
|  | char *eth_tx_buffer; | 
|  | char *eth_rx_buffer[NR]; | 
|  | int tdn, rdn; | 
|  | int dev; | 
|  | unsigned int reg_base; | 
|  | }; | 
|  |  | 
|  |  | 
|  | #ifdef CONFIG_INTEL_LXT97X | 
|  | /* for intel LXT972 */ | 
|  | static const char ether_port_phy_addr[3]={0,1,2}; | 
|  | #else | 
|  | static const char ether_port_phy_addr[3]={4,5,6}; | 
|  | #endif | 
|  |  | 
|  | /* MII PHY access routines are common for all i/f, use gal_ent0 */ | 
|  | #define GT6426x_MII_DEVNAME	"gal_enet0" | 
|  |  | 
|  | int gt6426x_miiphy_read(char *devname, unsigned char phy, | 
|  | unsigned char reg, unsigned short *val); | 
|  |  | 
|  | static inline unsigned short | 
|  | miiphy_read_ret(unsigned short phy, unsigned short reg) | 
|  | { | 
|  | unsigned short val; | 
|  | gt6426x_miiphy_read(GT6426x_MII_DEVNAME,phy,reg,&val); | 
|  | return val; | 
|  | } | 
|  |  | 
|  |  | 
|  | /************************************************************************** | 
|  | RESET - Reset adapter | 
|  | ***************************************************************************/ | 
|  | void | 
|  | gt6426x_eth_reset(void *v) | 
|  | { | 
|  | /*  we should do something here... | 
|  | struct eth_device *wp = (struct eth_device *)v; | 
|  | struct eth_dev_s *p = wp->priv; | 
|  | */ | 
|  |  | 
|  | printf ("RESET\n"); | 
|  | /* put the card in its initial state */ | 
|  | } | 
|  |  | 
|  | static void gt6426x_handle_SMI(struct eth_dev_s *p, unsigned int icr) | 
|  | { | 
|  | #ifdef DEBUG | 
|  | printf("SMI interrupt: "); | 
|  |  | 
|  | if(icr&0x20000000) { | 
|  | printf("SMI done\n"); | 
|  | } | 
|  | #endif | 
|  |  | 
|  | if(icr&0x10000000) { | 
|  | unsigned int psr; | 
|  | psr=GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + p->reg_base); | 
|  | #ifdef DEBUG | 
|  | printf("PHY state change:\n" | 
|  | "  GT:%s:%s:%s:%s\n", | 
|  | psr&1?"100":" 10", | 
|  | psr&8?" Link":"nLink", | 
|  | psr&2?"FD":"HD", | 
|  | psr&4?" FC":"nFC"); | 
|  |  | 
|  | #ifdef CONFIG_INTEL_LXT97X /* non-standard mii reg (intel lxt972a) */ | 
|  | { | 
|  | unsigned short mii_11; | 
|  | mii_11=miiphy_read_ret(ether_port_phy_addr[p->dev],0x11); | 
|  |  | 
|  | printf(" mii:%s:%s:%s:%s %s:%s %s\n", | 
|  | mii_11&(1<<14)?"100":" 10", | 
|  | mii_11&(1<<10)?" Link":"nLink", | 
|  | mii_11&(1<<9)?"FD":"HD", | 
|  | mii_11&(1<<4)?" FC":"nFC", | 
|  |  | 
|  | mii_11&(1<<7)?"ANc":"ANnc", | 
|  | mii_11&(1<<8)?"AN":"Manual", | 
|  | "" | 
|  | ); | 
|  | } | 
|  | #endif /* CONFIG_INTEL_LXT97X */ | 
|  | #endif /* DEBUG */ | 
|  | } | 
|  | } | 
|  |  | 
|  | static int | 
|  | gt6426x_eth_receive(struct eth_dev_s *p,unsigned int icr) | 
|  | { | 
|  | int eth_len=0; | 
|  | char *eth_data; | 
|  |  | 
|  | eth0_rx_desc_single *rx = &p->eth_rx_desc[(p->rdn)]; | 
|  |  | 
|  | INVALIDATE_DCACHE((unsigned int)rx,(unsigned int)(rx+1)); | 
|  |  | 
|  | if (rx->command_status & 0x80000000) { | 
|  | return 0; /* No packet received */ | 
|  | } | 
|  |  | 
|  | eth_len = (unsigned int) | 
|  | (rx->buff_size_byte_count) & 0x0000ffff; | 
|  | eth_data = (char *) p->eth_rx_buffer[p->rdn]; | 
|  |  | 
|  | #ifdef DEBUG | 
|  | if (eth_len) { | 
|  | printf ("%s: Recived %d byte Packet @ 0x%p\n", | 
|  | __FUNCTION__, eth_len, eth_data); | 
|  | } | 
|  | #endif | 
|  | /* | 
|  | * packet is now in: | 
|  | * eth0_rx_buffer[RDN_ETH0]; | 
|  | */ | 
|  |  | 
|  | /* let the upper layer handle the packet */ | 
|  | NetReceive ((uchar *)eth_data, eth_len); | 
|  |  | 
|  | rx->buff_size_byte_count = GT6426x_ETH_BUF_SIZE<<16; | 
|  |  | 
|  |  | 
|  | /* GT96100 Owner */ | 
|  | rx->command_status = 0x80000000; | 
|  |  | 
|  | FLUSH_DCACHE((unsigned int)rx,(unsigned int)(rx+1)); | 
|  |  | 
|  | p->rdn ++; | 
|  | if (p->rdn == NR) {p->rdn = 0;} | 
|  |  | 
|  | sync(); | 
|  |  | 
|  | /* Start Rx*/ | 
|  | GT_REG_WRITE (ETHERNET0_SDMA_COMMAND_REGISTER + p->reg_base, 0x00000080); | 
|  |  | 
|  | #ifdef DEBUG | 
|  | { | 
|  | int i; | 
|  | for (i=0;i<12;i++) { | 
|  | printf(" %02x", eth_data[i]); | 
|  | } | 
|  | } | 
|  | printf(": %d bytes\n", eth_len); | 
|  | #endif | 
|  | INVALIDATE_DCACHE((unsigned int)eth_data, | 
|  | (unsigned int)eth_data+eth_len); | 
|  | return eth_len; | 
|  | } | 
|  |  | 
|  | /************************************************************************** | 
|  | POLL - look for an rx frame, handle other conditions | 
|  | ***************************************************************************/ | 
|  | int | 
|  | gt6426x_eth_poll(void *v) | 
|  | { | 
|  | struct eth_device *wp = (struct eth_device *)v; | 
|  | struct eth_dev_s *p = wp->priv; | 
|  | unsigned int icr=GTREGREAD(ETHERNET0_INTERRUPT_CAUSE_REGISTER + p->reg_base); | 
|  |  | 
|  | if(icr) { | 
|  | GT_REG_WRITE(ETHERNET0_INTERRUPT_CAUSE_REGISTER +p->reg_base, 0); | 
|  | #ifdef DEBUG | 
|  | printf("poll got ICR %08x\n", icr); | 
|  | #endif | 
|  | /* SMI done or PHY state change*/ | 
|  | if(icr&0x30000000) gt6426x_handle_SMI(p, icr); | 
|  | } | 
|  | /* always process. We aren't using RX interrupts */ | 
|  | return gt6426x_eth_receive(p, icr); | 
|  | } | 
|  |  | 
|  | /************************************************************************** | 
|  | TRANSMIT - Transmit a frame | 
|  | ***************************************************************************/ | 
|  | int | 
|  | gt6426x_eth_transmit(void *v, volatile char *p, unsigned int s) | 
|  | { | 
|  | struct eth_device *wp = (struct eth_device *)v; | 
|  | struct eth_dev_s *dev = (struct eth_dev_s *)wp->priv; | 
|  | #ifdef DEBUG | 
|  | unsigned int old_command_stat,old_psr; | 
|  | #endif | 
|  | eth0_tx_desc_single *tx = &dev->eth_tx_desc[dev->tdn]; | 
|  |  | 
|  | /* wait for tx to be ready */ | 
|  | INVALIDATE_DCACHE((unsigned int)tx,(unsigned int)(tx+1)); | 
|  | while (tx->command_status & 0x80000000) { | 
|  | int i; | 
|  | for(i=0;i<1000;i++); | 
|  | INVALIDATE_DCACHE((unsigned int)tx,(unsigned int)(tx+1)); | 
|  | } | 
|  |  | 
|  | GT_REG_WRITE (ETHERNET0_CURRENT_TX_DESCRIPTOR_POINTER0 + dev->reg_base, | 
|  | (unsigned int)tx); | 
|  |  | 
|  | #ifdef DEBUG | 
|  | printf("copying to tx_buffer [%p], length %x, desc = %p\n", | 
|  | dev->eth_tx_buffer, s, dev->eth_tx_desc); | 
|  | #endif | 
|  | memcpy(dev->eth_tx_buffer, (char *) p, s); | 
|  |  | 
|  | tx->buff_pointer = (uchar *)dev->eth_tx_buffer; | 
|  | tx->bytecount_reserved = ((__u16)s) << 16; | 
|  |  | 
|  | /*    31 - own | 
|  | *    22 - gencrc | 
|  | * 18:16 - pad, last, first */ | 
|  | tx->command_status = (1<<31) | (1<<22) | (7<<16); | 
|  | #if 0 | 
|  | /* FEr #18 */ | 
|  | tx->next_desc = NULL; | 
|  | #else | 
|  | tx->next_desc = | 
|  | (struct eth0_tx_desc_struct *) | 
|  | &dev->eth_tx_desc[(dev->tdn+1)%NT].bytecount_reserved; | 
|  |  | 
|  | /* cpu owned */ | 
|  | dev->eth_tx_desc[(dev->tdn+1)%NT].command_status = (7<<16);	/* pad, last, first */ | 
|  | #endif | 
|  |  | 
|  | #ifdef DEBUG | 
|  | old_command_stat=tx->command_status, | 
|  | old_psr=GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + dev->reg_base); | 
|  | #endif | 
|  |  | 
|  | FLUSH_DCACHE((unsigned int)tx, | 
|  | (unsigned int)&dev->eth_tx_desc[(dev->tdn+2)%NT]); | 
|  |  | 
|  | FLUSH_DCACHE((unsigned int)dev->eth_tx_buffer,(unsigned int)dev->eth_tx_buffer+s); | 
|  |  | 
|  | GT_REG_WRITE(ETHERNET0_SDMA_COMMAND_REGISTER + dev->reg_base, 0x01000000); | 
|  |  | 
|  | #ifdef DEBUG | 
|  | { | 
|  | unsigned int command_stat=0; | 
|  | printf("cmd_stat: %08x PSR: %08x\n", old_command_stat, old_psr); | 
|  | /* wait for tx to be ready */ | 
|  | do { | 
|  | unsigned int psr=GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + dev->reg_base); | 
|  | command_stat=tx->command_status; | 
|  | if(command_stat!=old_command_stat || psr !=old_psr) { | 
|  | printf("cmd_stat: %08x PSR: %08x\n", command_stat, psr); | 
|  | old_command_stat = command_stat; | 
|  | old_psr = psr; | 
|  | } | 
|  | /* gt6426x_eth0_poll(); */ | 
|  | } while (command_stat & 0x80000000); | 
|  |  | 
|  | printf("sent %d byte frame\n", s); | 
|  |  | 
|  | if((command_stat & (3<<15)) == 3) { | 
|  | printf("frame had error (stat=%08x)\n", command_stat); | 
|  | } | 
|  | } | 
|  | #endif | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /************************************************************************** | 
|  | DISABLE - Turn off ethernet interface | 
|  | ***************************************************************************/ | 
|  | void | 
|  | gt6426x_eth_disable(void *v) | 
|  | { | 
|  | struct eth_device *wp = (struct eth_device *)v; | 
|  | struct eth_dev_s *p = (struct eth_dev_s *)wp->priv; | 
|  |  | 
|  | GT_REG_WRITE(ETHERNET0_SDMA_COMMAND_REGISTER + p->reg_base, 0x80008000); | 
|  | } | 
|  |  | 
|  | /************************************************************************** | 
|  | MII utilities - write: write to an MII register via SMI | 
|  | ***************************************************************************/ | 
|  | int | 
|  | gt6426x_miiphy_write(char *devname, unsigned char phy, | 
|  | unsigned char reg, unsigned short data) | 
|  | { | 
|  | unsigned int temp= (reg<<21) | (phy<<16) | data; | 
|  |  | 
|  | while(GTREGREAD(ETHERNET_SMI_REGISTER) & (1<<28));	/* wait for !Busy */ | 
|  |  | 
|  | GT_REG_WRITE(ETHERNET_SMI_REGISTER, temp); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /************************************************************************** | 
|  | MII utilities - read: read from an MII register via SMI | 
|  | ***************************************************************************/ | 
|  | int | 
|  | gt6426x_miiphy_read(char *devname, unsigned char phy, | 
|  | unsigned char reg, unsigned short *val) | 
|  | { | 
|  | unsigned int temp= (reg<<21) | (phy<<16) | 1<<26; | 
|  |  | 
|  | while(GTREGREAD(ETHERNET_SMI_REGISTER) & (1<<28));	/* wait for !Busy */ | 
|  |  | 
|  | GT_REG_WRITE(ETHERNET_SMI_REGISTER, temp); | 
|  |  | 
|  | while(1) { | 
|  | temp=GTREGREAD(ETHERNET_SMI_REGISTER); | 
|  | if(temp & (1<<27)) break;		/* wait for ReadValid */ | 
|  | } | 
|  | *val = temp & 0xffff; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #ifdef DEBUG | 
|  | /************************************************************************** | 
|  | MII utilities - dump mii registers | 
|  | ***************************************************************************/ | 
|  | static void | 
|  | gt6426x_dump_mii(bd_t *bis, unsigned short phy) | 
|  | { | 
|  | printf("mii reg 0 - 3:   %04x %04x %04x %04x\n", | 
|  | miiphy_read_ret(phy, 0x0), | 
|  | miiphy_read_ret(phy, 0x1), | 
|  | miiphy_read_ret(phy, 0x2), | 
|  | miiphy_read_ret(phy, 0x3) | 
|  | ); | 
|  | printf("        4 - 7:   %04x %04x %04x %04x\n", | 
|  | miiphy_read_ret(phy, 0x4), | 
|  | miiphy_read_ret(phy, 0x5), | 
|  | miiphy_read_ret(phy, 0x6), | 
|  | miiphy_read_ret(phy, 0x7) | 
|  | ); | 
|  | printf("        8:       %04x\n", | 
|  | miiphy_read_ret(phy, 0x8) | 
|  | ); | 
|  | printf("        16-19:   %04x %04x %04x %04x\n", | 
|  | miiphy_read_ret(phy, 0x10), | 
|  | miiphy_read_ret(phy, 0x11), | 
|  | miiphy_read_ret(phy, 0x12), | 
|  | miiphy_read_ret(phy, 0x13) | 
|  | ); | 
|  | printf("        20,30:   %04x %04x\n", | 
|  | miiphy_read_ret(phy, 20), | 
|  | miiphy_read_ret(phy, 30) | 
|  | ); | 
|  | } | 
|  | #endif | 
|  |  | 
|  | #ifdef RESTART_AUTONEG | 
|  |  | 
|  | /* If link is up && autoneg compleate, and if | 
|  | * GT and PHY disagree about link capabilitys, | 
|  | * restart autoneg - something screwy with FD/HD | 
|  | * unless we do this. */ | 
|  | static void | 
|  | check_phy_state(struct eth_dev_s *p) | 
|  | { | 
|  | int bmsr = miiphy_read_ret(ether_port_phy_addr[p->dev], PHY_BMSR); | 
|  | int psr = GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + p->reg_base); | 
|  |  | 
|  | if ((psr & 1<<3) && (bmsr & PHY_BMSR_LS)) { | 
|  | int nego = miiphy_read_ret(ether_port_phy_addr[p->dev], PHY_ANAR) & | 
|  | miiphy_read_ret(ether_port_phy_addr[p->dev], PHY_ANLPAR); | 
|  | int want; | 
|  |  | 
|  | if (nego & PHY_ANLPAR_TXFD) { | 
|  | want = 0x3; | 
|  | printf("MII: 100Base-TX, Full Duplex\n"); | 
|  | } else if (nego & PHY_ANLPAR_TX) { | 
|  | want = 0x1; | 
|  | printf("MII: 100Base-TX, Half Duplex\n"); | 
|  | } else if (nego & PHY_ANLPAR_10FD) { | 
|  | want = 0x2; | 
|  | printf("MII: 10Base-T, Full Duplex\n"); | 
|  | } else if (nego & PHY_ANLPAR_10) { | 
|  | want = 0x0; | 
|  | printf("MII: 10Base-T, Half Duplex\n"); | 
|  | } else { | 
|  | printf("MII: Unknown link-foo! %x\n", nego); | 
|  | return; | 
|  | } | 
|  |  | 
|  | if ((psr & 0x3) != want) { | 
|  | printf("MII: GT thinks %x, PHY thinks %x, restarting autoneg..\n", | 
|  | psr & 0x3, want); | 
|  | miiphy_write(GT6426x_MII_DEVNAME,ether_port_phy_addr[p->dev],0, | 
|  | miiphy_read_ret(ether_port_phy_addr[p->dev],0) | (1<<9)); | 
|  | udelay(10000);	/* the EVB's GT takes a while to notice phy | 
|  | went down and up */ | 
|  | } | 
|  | } | 
|  | } | 
|  | #endif | 
|  |  | 
|  | /************************************************************************** | 
|  | PROBE - Look for an adapter, this routine's visible to the outside | 
|  | ***************************************************************************/ | 
|  | int | 
|  | gt6426x_eth_probe(void *v, bd_t *bis) | 
|  | { | 
|  | struct eth_device *wp = (struct eth_device *)v; | 
|  | struct eth_dev_s *p = (struct eth_dev_s *)wp->priv; | 
|  | int dev = p->dev; | 
|  | unsigned int reg_base = p->reg_base; | 
|  | unsigned long temp; | 
|  | int i; | 
|  |  | 
|  | if (( dev < 0 ) || ( dev >= GAL_ETH_DEVS )) | 
|  | {	/* This should never happen */ | 
|  | printf("%s: Invalid device %d\n", __FUNCTION__, dev ); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #ifdef DEBUG | 
|  | printf ("%s: initializing %s\n", __FUNCTION__, wp->name ); | 
|  | printf ("\nCOMM_CONTROL = %08x , COMM_CONF = %08x\n", | 
|  | GTREGREAD(COMM_UNIT_ARBITER_CONTROL), | 
|  | GTREGREAD(COMM_UNIT_ARBITER_CONFIGURATION_REGISTER)); | 
|  | #endif | 
|  |  | 
|  | /* clear MIB counters */ | 
|  | for(i=0;i<255; i++) | 
|  | temp=GTREGREAD(ETHERNET0_MIB_COUNTER_BASE + reg_base +i); | 
|  |  | 
|  | #ifdef CONFIG_INTEL_LXT97X | 
|  | /* for intel LXT972 */ | 
|  |  | 
|  | /* led 1: 0x1=txact | 
|  | led 2: 0xc=link/rxact | 
|  | led 3: 0x2=rxact (N/C) | 
|  | strch: 0,2=30 ms, enable */ | 
|  | miiphy_write(GT6426x_MII_DEVNAME,ether_port_phy_addr[p->dev], 20, 0x1c22); | 
|  |  | 
|  | /* 2.7ns port rise time */ | 
|  | /*miiphy_write(ether_port_phy_addr[p->dev], 30, 0x0<<10); */ | 
|  | #else | 
|  | /* already set up in mpsc.c */ | 
|  | /*GT_REG_WRITE(MAIN_ROUTING_REGISTER, 0x7ffe38);	/  b400 */ | 
|  |  | 
|  | /* already set up in sdram_init.S... */ | 
|  | /* MPSC0, MPSC1, RMII */ | 
|  | /*GT_REG_WRITE(SERIAL_PORT_MULTIPLEX, 0x1102);		/  f010 */ | 
|  | #endif | 
|  | GT_REG_WRITE(ETHERNET_PHY_ADDRESS_REGISTER, | 
|  | ether_port_phy_addr[0]     | | 
|  | (ether_port_phy_addr[1]<<5) | | 
|  | (ether_port_phy_addr[2]<<10));			/* 2000 */ | 
|  |  | 
|  | /* 13:12 -   10: 4x64bit burst	(cache line size = 32 bytes) | 
|  | *    9  -    1: RIFB - interrupt on frame boundaries only | 
|  | *  6:7  -   00: big endian rx and tx | 
|  | *  5:2  - 1111: 15 retries */ | 
|  | GT_REG_WRITE(ETHERNET0_SDMA_CONFIGURATION_REGISTER + reg_base, | 
|  | (2<<12) | (1<<9) | (0xf<<2) );			/* 2440 */ | 
|  |  | 
|  | #ifndef USE_SOFTWARE_CACHE_MANAGEMENT | 
|  | /* enable rx/tx desc/buffer cache snoop */ | 
|  | GT_REG_READ(ETHERNET_0_ADDRESS_CONTROL_LOW + dev*0x20, | 
|  | &temp);						/* f200 */ | 
|  | temp|= (1<<6)| (1<<14)| (1<<22)| (1<<30); | 
|  | GT_REG_WRITE(ETHERNET_0_ADDRESS_CONTROL_LOW + dev*0x20, | 
|  | temp); | 
|  | #endif | 
|  |  | 
|  | /* 31  28 27  24 23  20 19  16 | 
|  | *  0000   0000   0000   0000	[0004] | 
|  | * 15  12 11  8   7  4   3  0 | 
|  | *  1000   1101   0000   0000	[4d00] | 
|  | *    20 - 0=MII 1=RMII | 
|  | *    19 - 0=speed autoneg | 
|  | * 15:14 - framesize 1536 (GT6426x_ETH_BUF_SIZE) | 
|  | *    11 - no force link pass | 
|  | *    10 - 1=disable fctl autoneg | 
|  | *     8 - override prio ?? */ | 
|  | temp = 0x00004d00; | 
|  | #ifndef CONFIG_ETHER_PORT_MII | 
|  | temp |= (1<<20);	/* RMII */ | 
|  | #endif | 
|  | /* set En */ | 
|  | GT_REG_WRITE(ETHERNET0_PORT_CONFIGURATION_EXTEND_REGISTER + reg_base, | 
|  | temp);				/* 2408 */ | 
|  |  | 
|  | /* hardcode E1 also? */ | 
|  | /* -- according to dox, this is safer due to extra pulldowns? */ | 
|  | if (dev<2) { | 
|  | GT_REG_WRITE(ETHERNET0_PORT_CONFIGURATION_EXTEND_REGISTER + (dev+1) * 0x400, | 
|  | temp);				/* 2408 */ | 
|  | } | 
|  |  | 
|  | /* wake up MAC */				 /* 2400 */ | 
|  | GT_REG_READ(ETHERNET0_PORT_CONFIGURATION_REGISTER + reg_base, &temp); | 
|  | temp |= (1<<7);		/* enable port */ | 
|  | #ifdef CONFIG_GT_USE_MAC_HASH_TABLE | 
|  | temp |= (1<<12);	/* hash size 1/2k */ | 
|  | #else | 
|  | temp |= 1;		/* promisc */ | 
|  | #endif | 
|  | GT_REG_WRITE(ETHERNET0_PORT_CONFIGURATION_REGISTER + reg_base, temp); | 
|  | /* 2400 */ | 
|  |  | 
|  | #ifdef RESTART_AUTONEG | 
|  | check_phy_state(p); | 
|  | #endif | 
|  |  | 
|  | printf("%s: Waiting for link up..\n", wp->name); | 
|  | temp = 10 * 1000; | 
|  | /* wait for link back up */ | 
|  | while(!(GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + reg_base) & 8) | 
|  | && (--temp > 0)){ | 
|  | udelay(1000);	/* wait 1 ms */ | 
|  | } | 
|  | if ( temp == 0) { | 
|  | printf("%s: Failed!\n", wp->name); | 
|  | return (0); | 
|  | } | 
|  |  | 
|  | printf("%s: OK!\n", wp->name); | 
|  |  | 
|  | p->tdn = 0; | 
|  | p->rdn = 0; | 
|  | p->eth_tx_desc[p->tdn].command_status = 0; | 
|  |  | 
|  | /* Initialize Rx Side */ | 
|  | for (temp = 0; temp < NR; temp++) { | 
|  | p->eth_rx_desc[temp].buff_pointer = (uchar *)p->eth_rx_buffer[temp]; | 
|  | p->eth_rx_desc[temp].buff_size_byte_count = GT6426x_ETH_BUF_SIZE<<16; | 
|  |  | 
|  | /* GT96100 Owner */ | 
|  | p->eth_rx_desc[temp].command_status = 0x80000000; | 
|  | p->eth_rx_desc[temp].next_desc = | 
|  | (struct eth0_rx_desc_struct *) | 
|  | &p->eth_rx_desc[(temp+1)%NR].buff_size_byte_count; | 
|  | } | 
|  |  | 
|  | FLUSH_DCACHE((unsigned int)&p->eth_tx_desc[0], | 
|  | (unsigned int)&p->eth_tx_desc[NR]); | 
|  | FLUSH_DCACHE((unsigned int)&p->eth_rx_desc[0], | 
|  | (unsigned int)&p->eth_rx_desc[NR]); | 
|  |  | 
|  | GT_REG_WRITE(ETHERNET0_CURRENT_TX_DESCRIPTOR_POINTER0 + reg_base, | 
|  | (unsigned int) p->eth_tx_desc); | 
|  | GT_REG_WRITE(ETHERNET0_FIRST_RX_DESCRIPTOR_POINTER0 + reg_base, | 
|  | (unsigned int) p->eth_rx_desc); | 
|  | GT_REG_WRITE(ETHERNET0_CURRENT_RX_DESCRIPTOR_POINTER0 + reg_base, | 
|  | (unsigned int) p->eth_rx_desc); | 
|  |  | 
|  | #ifdef DEBUG | 
|  | printf ("\nRx descriptor pointer is %08x %08x\n", | 
|  | GTREGREAD(ETHERNET0_FIRST_RX_DESCRIPTOR_POINTER0 + reg_base), | 
|  | GTREGREAD(ETHERNET0_CURRENT_RX_DESCRIPTOR_POINTER0 + reg_base)); | 
|  | printf ("\n\n%08x %08x\n", | 
|  | (unsigned int)p->eth_rx_desc,p->eth_rx_desc[0].command_status); | 
|  |  | 
|  | printf ("Descriptor dump:\n"); | 
|  | printf ("cmd status: %08x\n",p->eth_rx_desc[0].command_status); | 
|  | printf ("byte_count: %08x\n",p->eth_rx_desc[0].buff_size_byte_count); | 
|  | printf ("buff_ptr: %08x\n",(unsigned int)p->eth_rx_desc[0].buff_pointer); | 
|  | printf ("next_desc: %08x\n\n",(unsigned int)p->eth_rx_desc[0].next_desc); | 
|  | printf ("%08x\n",*(unsigned int *) ((unsigned int)p->eth_rx_desc + 0x0)); | 
|  | printf ("%08x\n",*(unsigned int *) ((unsigned int)p->eth_rx_desc + 0x4)); | 
|  | printf ("%08x\n",*(unsigned int *) ((unsigned int)p->eth_rx_desc + 0x8)); | 
|  | printf ("%08x\n\n", | 
|  | *(unsigned int *) ((unsigned int)p->eth_rx_desc + 0xc)); | 
|  | #endif | 
|  |  | 
|  | #ifdef DEBUG | 
|  | gt6426x_dump_mii(bis,ether_port_phy_addr[p->dev]); | 
|  | #endif | 
|  |  | 
|  | #ifdef CONFIG_GT_USE_MAC_HASH_TABLE | 
|  | { | 
|  | unsigned int hashtable_base; | 
|  | u8 *b = (u8 *)(wp->enetaddr); | 
|  | u32 macH, macL; | 
|  |  | 
|  | /* twist the MAC up into the way the discovery wants it */ | 
|  | macH= (b[0]<<8) | b[1]; | 
|  | macL= (b[2]<<24) | (b[3]<<16) | (b[4]<<8) | b[5]; | 
|  |  | 
|  | /* mode 0, size 0x800 */ | 
|  | hashtable_base =initAddressTable(dev,0,1); | 
|  |  | 
|  | if(!hashtable_base) { | 
|  | printf("initAddressTable failed\n"); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | addAddressTableEntry(dev, macH, macL, 1, 0); | 
|  | GT_REG_WRITE(ETHERNET0_HASH_TABLE_POINTER_REGISTER + reg_base, | 
|  | hashtable_base); | 
|  | } | 
|  | #endif | 
|  |  | 
|  | /* Start Rx*/ | 
|  | GT_REG_WRITE(ETHERNET0_SDMA_COMMAND_REGISTER + reg_base, 0x00000080); | 
|  | printf("%s: gt6426x eth device %d init success \n", wp->name, dev ); | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | /* enter all the galileo ethernet devs into MULTI-BOOT */ | 
|  | void | 
|  | gt6426x_eth_initialize(bd_t *bis) | 
|  | { | 
|  | struct eth_device *dev; | 
|  | struct eth_dev_s *p; | 
|  | int devnum, x, temp; | 
|  | char *s, *e, buf[64]; | 
|  |  | 
|  | #ifdef DEBUG | 
|  | printf( "\n%s\n", __FUNCTION ); | 
|  | #endif | 
|  |  | 
|  | for (devnum = 0; devnum < GAL_ETH_DEVS; devnum++) { | 
|  | dev = calloc(sizeof(*dev), 1); | 
|  | if (!dev) { | 
|  | printf( "%s: gal_enet%d allocation failure, %s\n", | 
|  | __FUNCTION__, devnum, "eth_device structure"); | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* must be less than NAMESIZE (16) */ | 
|  | sprintf(dev->name, "gal_enet%d", devnum); | 
|  |  | 
|  | #ifdef DEBUG | 
|  | printf( "Initializing %s\n", dev->name ); | 
|  | #endif | 
|  |  | 
|  | /* Extract the MAC address from the environment */ | 
|  | switch (devnum) | 
|  | { | 
|  | case 0: s = "ethaddr"; break; | 
|  | #if (GAL_ETH_DEVS > 1) | 
|  | case 1: s = "eth1addr"; break; | 
|  | #endif | 
|  | #if (GAL_ETH_DEVS > 2) | 
|  | case 2: s = "eth2addr";	break; | 
|  | #endif | 
|  | default: /* this should never happen */ | 
|  | printf( "%s: Invalid device number %d\n", | 
|  | __FUNCTION__, devnum ); | 
|  | return; | 
|  | } | 
|  |  | 
|  | temp = getenv_r (s, buf, sizeof(buf)); | 
|  | s = (temp > 0) ? buf : NULL; | 
|  |  | 
|  | #ifdef DEBUG | 
|  | printf ("Setting MAC %d to %s\n", devnum, s ); | 
|  | #endif | 
|  | for (x = 0; x < 6; ++x) { | 
|  | dev->enetaddr[x] = s ? simple_strtoul(s, &e, 16) : 0; | 
|  | if (s) | 
|  | s = (*e) ? e+1 : e; | 
|  | } | 
|  |  | 
|  | dev->init = (void*)gt6426x_eth_probe; | 
|  | dev->halt = (void*)gt6426x_eth_reset; | 
|  | dev->send = (void*)gt6426x_eth_transmit; | 
|  | dev->recv = (void*)gt6426x_eth_poll; | 
|  |  | 
|  | p = calloc( sizeof(*p), 1 ); | 
|  | dev->priv = (void*)p; | 
|  | if (!p) | 
|  | { | 
|  | printf( "%s: %s allocation failure, %s\n", | 
|  | __FUNCTION__, dev->name, "Private Device Structure"); | 
|  | free(dev); | 
|  | return; | 
|  | } | 
|  |  | 
|  | p->dev = devnum; | 
|  | p->tdn=0; | 
|  | p->rdn=0; | 
|  | p->reg_base = devnum * ETHERNET_PORTS_DIFFERENCE_OFFSETS; | 
|  |  | 
|  | p->eth_tx_desc = | 
|  | (eth0_tx_desc_single *) | 
|  | (((unsigned int) malloc(sizeof (eth0_tx_desc_single) * | 
|  | (NT+1)) & 0xfffffff0) + 0x10); | 
|  | if (!p) | 
|  | { | 
|  | printf( "%s: %s allocation failure, %s\n", | 
|  | __FUNCTION__, dev->name, "Tx Descriptor"); | 
|  | free(dev); | 
|  | return; | 
|  | } | 
|  |  | 
|  | p->eth_rx_desc = | 
|  | (eth0_rx_desc_single *) | 
|  | (((unsigned int) malloc(sizeof (eth0_rx_desc_single) * | 
|  | (NR+1)) & 0xfffffff0) + 0x10); | 
|  | if (!p->eth_rx_desc) | 
|  | { | 
|  | printf( "%s: %s allocation failure, %s\n", | 
|  | __FUNCTION__, dev->name, "Rx Descriptor"); | 
|  | free(dev); | 
|  | free(p); | 
|  | return; | 
|  | } | 
|  |  | 
|  | p->eth_tx_buffer = | 
|  | (char *) (((unsigned int) malloc(GT6426x_ETH_BUF_SIZE) & 0xfffffff0) + 0x10); | 
|  | if (!p->eth_tx_buffer) | 
|  | { | 
|  | printf( "%s: %s allocation failure, %s\n", | 
|  | __FUNCTION__, dev->name, "Tx Bufffer"); | 
|  | free(dev); | 
|  | free(p); | 
|  | free(p->eth_rx_desc); | 
|  | return; | 
|  | } | 
|  |  | 
|  | for (temp = 0 ; temp < NR ; temp ++) { | 
|  | p->eth_rx_buffer[temp] = | 
|  | (char *) | 
|  | (((unsigned int) malloc(GT6426x_ETH_BUF_SIZE) & 0xfffffff0) + 0x10); | 
|  | if (!p->eth_rx_buffer[temp]) | 
|  | { | 
|  | printf( "%s: %s allocation failure, %s\n", | 
|  | __FUNCTION__, dev->name, "Rx Buffers"); | 
|  | free(dev); | 
|  | free(p); | 
|  | free(p->eth_tx_buffer); | 
|  | free(p->eth_rx_desc); | 
|  | free(p->eth_tx_desc); | 
|  | while (temp >= 0) | 
|  | free(p->eth_rx_buffer[--temp]); | 
|  | return; | 
|  | } | 
|  | } | 
|  |  | 
|  |  | 
|  | eth_register(dev); | 
|  | #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) | 
|  | miiphy_register(dev->name, | 
|  | gt6426x_miiphy_read, gt6426x_miiphy_write); | 
|  | #endif | 
|  | } | 
|  |  | 
|  | } | 
|  | #endif |