blob: 7e7646a2e15a6c0d12b14199178be5b812a6a4f6 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2011 by Vladimir Zapolskiy <vz@mleia.com>
*/
#include <common.h>
#include <dm.h>
#include <ns16550.h>
#include <dm/platform_data/lpc32xx_hsuart.h>
#include <asm/arch/clk.h>
#include <asm/arch/uart.h>
#include <asm/arch/mux.h>
#include <asm/io.h>
static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
static struct uart_ctrl_regs *ctrl = (struct uart_ctrl_regs *)UART_CTRL_BASE;
static struct mux_regs *mux = (struct mux_regs *)MUX_BASE;
void lpc32xx_uart_init(unsigned int uart_id)
{
if (uart_id < 1 || uart_id > 7)
return;
/* Disable loopback mode, if it is set by S1L bootloader */
clrbits_le32(&ctrl->loop,
UART_LOOPBACK(CONFIG_SYS_LPC32XX_UART));
if (uart_id < 3 || uart_id > 6)
return;
/* Enable UART system clock */
setbits_le32(&clk->uartclk_ctrl, CLK_UART(uart_id));
/* Set UART into autoclock mode */
clrsetbits_le32(&ctrl->clkmode,
UART_CLKMODE_MASK(uart_id),
UART_CLKMODE_AUTO(uart_id));
/* Bypass pre-divider of UART clock */
writel(CLK_UART_X_DIV(1) | CLK_UART_Y_DIV(1),
&clk->u3clk + (uart_id - 3));
}
#if !CONFIG_IS_ENABLED(OF_CONTROL)
static const struct ns16550_platdata lpc32xx_uart[] = {
{ .base = UART3_BASE, .reg_shift = 2,
.clock = CONFIG_SYS_NS16550_CLK, .fcr = UART_FCR_DEFVAL, },
{ .base = UART4_BASE, .reg_shift = 2,
.clock = CONFIG_SYS_NS16550_CLK, .fcr = UART_FCR_DEFVAL, },
{ .base = UART5_BASE, .reg_shift = 2,
.clock = CONFIG_SYS_NS16550_CLK, .fcr = UART_FCR_DEFVAL, },
{ .base = UART6_BASE, .reg_shift = 2,
.clock = CONFIG_SYS_NS16550_CLK, .fcr = UART_FCR_DEFVAL, },
};
#if defined(CONFIG_LPC32XX_HSUART)
static const struct lpc32xx_hsuart_platdata lpc32xx_hsuart[] = {
{ HS_UART1_BASE, },
{ HS_UART2_BASE, },
{ HS_UART7_BASE, },
};
#endif
U_BOOT_DEVICES(lpc32xx_uarts) = {
#if defined(CONFIG_LPC32XX_HSUART)
{ "lpc32xx_hsuart", &lpc32xx_hsuart[0], },
{ "lpc32xx_hsuart", &lpc32xx_hsuart[1], },
#endif
{ "ns16550_serial", &lpc32xx_uart[0], },
{ "ns16550_serial", &lpc32xx_uart[1], },
{ "ns16550_serial", &lpc32xx_uart[2], },
{ "ns16550_serial", &lpc32xx_uart[3], },
#if defined(CONFIG_LPC32XX_HSUART)
{ "lpc32xx_hsuart", &lpc32xx_hsuart[2], },
#endif
};
#endif
void lpc32xx_dma_init(void)
{
/* Enable DMA interface */
writel(CLK_DMA_ENABLE, &clk->dmaclk_ctrl);
}
void lpc32xx_mac_init(void)
{
/* Enable MAC interface */
writel(CLK_MAC_REG | CLK_MAC_SLAVE | CLK_MAC_MASTER
#if defined(CONFIG_RMII)
| CLK_MAC_RMII,
#else
| CLK_MAC_MII,
#endif
&clk->macclk_ctrl);
}
void lpc32xx_mlc_nand_init(void)
{
/* Enable NAND interface */
writel(CLK_NAND_MLC | CLK_NAND_MLC_INT, &clk->flashclk_ctrl);
}
void lpc32xx_slc_nand_init(void)
{
/* Enable SLC NAND interface */
writel(CLK_NAND_SLC | CLK_NAND_SLC_SELECT, &clk->flashclk_ctrl);
}
void lpc32xx_usb_init(void)
{
/* Do not route the UART 5 Tx/Rx pins to the USB D+ and USB D- pins. */
clrbits_le32(&ctrl->ctrl, UART_CTRL_UART5_USB_MODE);
}
void lpc32xx_i2c_init(unsigned int devnum)
{
/* Enable I2C interface */
uint32_t ctrl = readl(&clk->i2cclk_ctrl);
if (devnum == 1)
ctrl |= CLK_I2C1_ENABLE;
if (devnum == 2)
ctrl |= CLK_I2C2_ENABLE;
writel(ctrl, &clk->i2cclk_ctrl);
}
U_BOOT_DEVICE(lpc32xx_gpios) = {
.name = "gpio_lpc32xx"
};
/* Mux for SCK0, MISO0, MOSI0. We do not use SSEL0. */
#define P_MUX_SET_SSP0 0x1600
void lpc32xx_ssp_init(void)
{
/* Enable SSP0 interface */
writel(CLK_SSP0_ENABLE_CLOCK, &clk->ssp_ctrl);
/* Mux SSP0 pins */
writel(P_MUX_SET_SSP0, &mux->p_mux_set);
}