| /* |
| * Bluewater Systems Snapper 9260 and 9G20 modules |
| * |
| * (C) Copyright 2011 Bluewater Systems |
| * Author: Andre Renaud <andre@bluewatersys.com> |
| * Author: Ryan Mallon <ryan@bluewatersys.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* SoC type is defined in boards.cfg */ |
| #include <asm/hardware.h> |
| #include <asm/sizes.h> |
| |
| #define CONFIG_SYS_TEXT_BASE 0x20000000 |
| |
| /* ARM asynchronous clock */ |
| #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* External Crystal, in Hz */ |
| #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 |
| #define CONFIG_SYS_HZ 1000 |
| |
| /* CPU */ |
| #define CONFIG_ARCH_CPU_INIT |
| |
| #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ |
| #define CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_INITRD_TAG |
| #define CONFIG_SKIP_LOWLEVEL_INIT |
| #define CONFIG_SKIP_RELOCATE_UBOOT |
| #define CONFIG_DISPLAY_CPUINFO |
| #define CONFIG_FIT |
| |
| /* SDRAM */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 |
| #define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* 64MB */ |
| #define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM1 + 0x1000 - \ |
| GENERATED_GBL_DATA_SIZE) |
| |
| /* Mem test settings */ |
| #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE |
| #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + (1024 * 1024)) |
| |
| /* NAND Flash */ |
| #define CONFIG_NAND_ATMEL |
| #define CONFIG_SYS_NO_FLASH |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 |
| #define CONFIG_SYS_NAND_DBW_8 |
| #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* AD21 */ |
| #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* AD22 */ |
| #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 |
| #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 |
| |
| /* Ethernet */ |
| #define CONFIG_MACB |
| #define CONFIG_RMII |
| #define CONFIG_NET_RETRY_COUNT 20 |
| #define CONFIG_RESET_PHY_R |
| #define CONFIG_TFTP_PORT |
| #define CONFIG_TFTP_TSIZE |
| |
| /* USB */ |
| #define CONFIG_USB_ATMEL |
| #define CONFIG_USB_OHCI_NEW |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 |
| #define CONFIG_USB_STORAGE |
| |
| /* GPIOs and IO expander */ |
| #define CONFIG_AT91_LEGACY |
| #define CONFIG_ATMEL_LEGACY |
| #define CONFIG_AT91_GPIO |
| #define CONFIG_AT91_GPIO_PULLUP 1 |
| #define CONFIG_PCA953X |
| #define CONFIG_SYS_I2C_PCA953X_ADDR 0x28 |
| #define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x28, 16} } |
| |
| /* UARTs/Serial console */ |
| #define CONFIG_ATMEL_USART |
| #define CONFIG_USART_BASE ATMEL_BASE_DBGU |
| #define CONFIG_USART_ID ATMEL_ID_SYS |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_SYS_PROMPT "Snapper> " |
| |
| /* I2C - Bit-bashed */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ |
| #define CONFIG_SYS_I2C_SOFT_SPEED 100000 |
| #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F |
| #define CONFIG_SOFT_I2C_READ_REPEATED_START |
| #define I2C_INIT do { \ |
| at91_set_gpio_output(AT91_PIN_PA23, 1); \ |
| at91_set_gpio_output(AT91_PIN_PA24, 1); \ |
| at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \ |
| at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \ |
| } while (0) |
| #define I2C_SOFT_DECLARATIONS |
| #define I2C_ACTIVE |
| #define I2C_TRISTATE at91_set_gpio_input(AT91_PIN_PA23, 1); |
| #define I2C_READ at91_get_gpio_value(AT91_PIN_PA23); |
| #define I2C_SDA(bit) do { \ |
| if (bit) { \ |
| at91_set_gpio_input(AT91_PIN_PA23, 1); \ |
| } else { \ |
| at91_set_gpio_output(AT91_PIN_PA23, 1); \ |
| at91_set_gpio_value(AT91_PIN_PA23, bit); \ |
| } \ |
| } while (0) |
| #define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTA, 24, bit) |
| #define I2C_DELAY udelay(2) |
| |
| /* Boot options */ |
| #define CONFIG_SYS_LOAD_ADDR 0x23000000 |
| #define CONFIG_BOOTDELAY 3 |
| #define CONFIG_ZERO_BOOTDELAY_CHECK |
| |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| /* Environment settings */ |
| #define CONFIG_ENV_IS_IN_NAND |
| #define CONFIG_ENV_OFFSET (512 << 10) |
| #define CONFIG_ENV_SIZE (256 << 10) |
| #define CONFIG_ENV_OVERWRITE |
| #define CONFIG_BOOTARGS "console=ttyS0,115200 ip=any" |
| |
| /* Console settings */ |
| #define CONFIG_SYS_CBSIZE 256 |
| #define CONFIG_SYS_MAXARGS 16 |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ |
| sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_LONGHELP |
| #define CONFIG_CMDLINE_EDITING |
| #define CONFIG_AUTO_COMPLETE |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| /* U-Boot memory settings */ |
| #define CONFIG_SYS_MALLOC_LEN (1 << 20) |
| |
| /* Command line configuration */ |
| #include <config_cmd_default.h> |
| #undef CONFIG_CMD_BDI |
| #undef CONFIG_CMD_FPGA |
| #undef CONFIG_CMD_IMI |
| #undef CONFIG_CMD_IMLS |
| #undef CONFIG_CMD_LOADS |
| #undef CONFIG_CMD_SOURCE |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_I2C |
| #undef CONFIG_CMD_GPIO |
| #define CONFIG_CMD_USB |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_PCA953X |
| #define CONFIG_CMD_PCA953X_INFO |
| |
| #endif /* __CONFIG_H */ |
