blob: 873ba6e91c9d81cf004f97ccf9f595a9b97933b6 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011
* eInfochips Ltd. <www.einfochips.com>
* Written-by: Ajay Bhargav <contact@8051projects.net>
*
* (C) Copyright 2010
* Marvell Semiconductor <www.marvell.com>
*/
#ifndef __ARMADA100_SPI_H_
#define __ARMADA100_SPI_H_
#include <asm/arch/armada100.h>
#define CAT_BASE_ADDR(x) ARMD1_SSP ## x ## _BASE
#define SSP_REG_BASE(x) CAT_BASE_ADDR(x)
/*
* SSP Serial Port Registers
* refer Appendix A.26
*/
struct ssp_reg {
u32 sscr0; /* SSP Control Register 0 - 0x000 */
u32 sscr1; /* SSP Control Register 1 - 0x004 */
u32 sssr; /* SSP Status Register - 0x008 */
u32 ssitr; /* SSP Interrupt Test Register - 0x00C */
u32 ssdr; /* SSP Data Register - 0x010 */
u32 pad1[5];
u32 ssto; /* SSP Timeout Register - 0x028 */
u32 sspsp; /* SSP Programmable Serial Protocol Register - 0x02C */
u32 sstsa; /* SSP TX Timeslot Active Register - 0x030 */
u32 ssrsa; /* SSP RX Timeslot Active Register - 0x034 */
u32 sstss; /* SSP Timeslot Status Register - 0x038 */
};
#define DEFAULT_WORD_LEN 8
#define SSP_FLUSH_NUM 0x2000
#define RX_THRESH_DEF 8
#define TX_THRESH_DEF 8
#define TIMEOUT_DEF 1000
#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */
#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */
#define SSCR1_LBM (1 << 2) /* Loop-Back Mode */
#define SSCR1_SPO (1 << 3) /* Motorola SPI SSPSCLK polarity
setting */
#define SSCR1_SPH (1 << 4) /* Motorola SPI SSPSCLK phase setting */
#define SSCR1_MWDS (1 << 5) /* Microwire Transmit Data Size */
#define SSCR1_TFT 0x03c0 /* Transmit FIFO Threshold (mask) */
#define SSCR1_RFT 0x3c00 /* Receive FIFO Threshold (mask) */
#define SSCR1_TXTRESH(x) ((x - 1) << 6) /* level [1..16] */
#define SSCR1_RXTRESH(x) ((x - 1) << 10) /* level [1..16] */
#define SSCR1_TINTE (1 << 19) /* Receiver Time-out
Interrupt enable */
#define SSCR0_DSS 0x0f /* Data Size Select (mask) */
#define SSCR0_DATASIZE(x) (x - 1) /* Data Size Select [4..16] */
#define SSCR0_FRF 0x30 /* FRame Format (mask) */
#define SSCR0_MOTO (0x0 << 4) /* Motorola's Serial
Peripheral Interface */
#define SSCR0_TI (0x1 << 4) /* TI's Synchronous
Serial Protocol (SSP) */
#define SSCR0_NATIONAL (0x2 << 4) /* National Microwire */
#define SSCR0_ECS (1 << 6) /* External clock select */
#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port
Enable */
#define SSSR_TNF (1 << 2) /* Transmit FIFO Not Full */
#define SSSR_RNE (1 << 3) /* Receive FIFO Not Empty */
#define SSSR_BSY (1 << 4) /* SSP Busy */
#define SSSR_TFS (1 << 5) /* Transmit FIFO Service Request */
#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */
#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */
#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */
#endif /* __ARMADA100_SPI_H_ */