blob: d38412e2c6a149105962b8860cc808c002dd76d2 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Memory Setup stuff - taken from blob memsetup.S
*
* Copyright (C) 2009 Samsung Electronics
* Kyungmin Park <kyungmin.park@samsung.com>
*/
#include <config.h>
#include <asm/arch/cpu.h>
#include <asm/arch/clock.h>
#include <asm/arch/power.h>
/*
* Register usages:
*
* r5 has zero always
* r7 has S5PC100 GPIO base, 0xE0300000
* r8 has real GPIO base, 0xE0300000, 0xE0200000 at S5PC100, S5PC110 repectively
* r9 has Mobile DDR size, 1 means 1GiB, 2 means 2GiB and so on
*/
.globl lowlevel_init
lowlevel_init:
mov r11, lr
/* r5 has always zero */
mov r5, #0
ldr r7, =S5PC100_GPIO_BASE
ldr r8, =S5PC100_GPIO_BASE
/* Read CPU ID */
ldr r2, =S5PC110_PRO_ID
ldr r0, [r2]
mov r1, #0x00010000
and r0, r0, r1
cmp r0, r5
beq 100f
ldr r8, =S5PC110_GPIO_BASE
100:
/* Turn on KEY_LED_ON [GPJ4(1)] XMSMWEN */
cmp r7, r8
beq skip_check_didle @ Support C110 only
ldr r0, =S5PC110_RST_STAT
ldr r1, [r0]
and r1, r1, #0x000D0000
cmp r1, #(0x1 << 19) @ DEEPIDLE_WAKEUP
beq didle_wakeup
cmp r7, r8
skip_check_didle:
addeq r0, r8, #0x280 @ S5PC100_GPIO_J4
addne r0, r8, #0x2C0 @ S5PC110_GPIO_J4
ldr r1, [r0, #0x0] @ GPIO_CON_OFFSET
bic r1, r1, #(0xf << 4) @ 1 * 4-bit
orr r1, r1, #(0x1 << 4)
str r1, [r0, #0x0] @ GPIO_CON_OFFSET
ldr r1, [r0, #0x4] @ GPIO_DAT_OFFSET
bic r1, r1, #(1 << 1)
str r1, [r0, #0x4] @ GPIO_DAT_OFFSET
/* Don't setup at s5pc100 */
beq 100f
/*
* Initialize Async Register Setting for EVT1
* Because we are setting EVT1 as the default value of EVT0,
* setting EVT0 as well does not make things worse.
* Thus, for the simplicity, we set for EVT0, too
*
* The "Async Registers" are:
* 0xE0F0_0000
* 0xE1F0_0000
* 0xF180_0000
* 0xF190_0000
* 0xF1A0_0000
* 0xF1B0_0000
* 0xF1C0_0000
* 0xF1D0_0000
* 0xF1E0_0000
* 0xF1F0_0000
* 0xFAF0_0000
*/
ldr r0, =0xe0f00000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xe1f00000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xf1800000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xf1900000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xf1a00000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xf1b00000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xf1c00000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xf1d00000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xf1e00000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xf1f00000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
ldr r0, =0xfaf00000
ldr r1, [r0]
bic r1, r1, #0x1
str r1, [r0]
/*
* Diable ABB block to reduce sleep current at low temperature
* Note that it's hidden register setup don't modify it
*/
ldr r0, =0xE010C300
ldr r1, =0x00800000
str r1, [r0]
100:
/* IO retension release */
ldreq r0, =S5PC100_OTHERS @ 0xE0108200
ldrne r0, =S5PC110_OTHERS @ 0xE010E000
ldr r1, [r0]
ldreq r2, =(1 << 31) @ IO_RET_REL
ldrne r2, =((1 << 31) | (1 << 30) | (1 << 29) | (1 << 28))
orr r1, r1, r2
/* Do not release retention here for S5PC110 */
streq r1, [r0]
/* Disable Watchdog */
ldreq r0, =S5PC100_WATCHDOG_BASE @ 0xEA200000
ldrne r0, =S5PC110_WATCHDOG_BASE @ 0xE2700000
str r5, [r0]
/* setting SRAM */
ldreq r0, =S5PC100_SROMC_BASE
ldrne r0, =S5PC110_SROMC_BASE
ldr r1, =0x9
str r1, [r0]
/* S5PC100 has 3 groups of interrupt sources */
ldreq r0, =S5PC100_VIC0_BASE @ 0xE4000000
ldrne r0, =S5PC110_VIC0_BASE @ 0xF2000000
add r1, r0, #0x00100000
add r2, r0, #0x00200000
/* Disable all interrupts (VIC0, VIC1 and VIC2) */
mvn r3, #0x0
str r3, [r0, #0x14] @ INTENCLEAR
str r3, [r1, #0x14] @ INTENCLEAR
str r3, [r2, #0x14] @ INTENCLEAR
/* Set all interrupts as IRQ */
str r5, [r0, #0xc] @ INTSELECT
str r5, [r1, #0xc] @ INTSELECT
str r5, [r2, #0xc] @ INTSELECT
/* Pending Interrupt Clear */
str r5, [r0, #0xf00] @ INTADDRESS
str r5, [r1, #0xf00] @ INTADDRESS
str r5, [r2, #0xf00] @ INTADDRESS
/* for UART */
bl uart_asm_init
bl internal_ram_init
cmp r7, r8
/* Clear wakeup status register */
ldreq r0, =S5PC100_WAKEUP_STAT
ldrne r0, =S5PC110_WAKEUP_STAT
ldr r1, [r0]
str r1, [r0]
/* IO retension release */
ldreq r0, =S5PC100_OTHERS @ 0xE0108200
ldrne r0, =S5PC110_OTHERS @ 0xE010E000
ldr r1, [r0]
ldreq r2, =(1 << 31) @ IO_RET_REL
ldrne r2, =((1 << 31) | (1 << 30) | (1 << 29) | (1 << 28))
orr r1, r1, r2
str r1, [r0]
b 1f
didle_wakeup:
/* Wait when APLL is locked */
ldr r0, =0xE0100100 @ S5PC110_APLL_CON
lockloop:
ldr r1, [r0]
and r1, r1, #(1 << 29)
cmp r1, #(1 << 29)
bne lockloop
ldr r0, =S5PC110_INFORM0
ldr r1, [r0]
mov pc, r1
nop
nop
nop
nop
nop
1:
mov lr, r11
mov pc, lr
/*
* system_clock_init: Initialize core clock and bus clock.
* void system_clock_init(void)
*/
system_clock_init:
ldr r0, =S5PC110_CLOCK_BASE @ 0xE0100000
/* Check S5PC100 */
cmp r7, r8
bne 110f
100:
/* Set Lock Time */
ldr r1, =0xe10 @ Locktime : 0xe10 = 3600
str r1, [r0, #0x000] @ S5PC100_APLL_LOCK
str r1, [r0, #0x004] @ S5PC100_MPLL_LOCK
str r1, [r0, #0x008] @ S5PC100_EPLL_LOCK
str r1, [r0, #0x00C] @ S5PC100_HPLL_LOCK
/* S5P_APLL_CON */
ldr r1, =0x81bc0400 @ SDIV 0, PDIV 4, MDIV 444 (1333MHz)
str r1, [r0, #0x100]
/* S5P_MPLL_CON */
ldr r1, =0x80590201 @ SDIV 1, PDIV 2, MDIV 89 (267MHz)
str r1, [r0, #0x104]
/* S5P_EPLL_CON */
ldr r1, =0x80870303 @ SDIV 3, PDIV 3, MDIV 135 (67.5MHz)
str r1, [r0, #0x108]
/* S5P_HPLL_CON */
ldr r1, =0x80600603 @ SDIV 3, PDIV 6, MDIV 96
str r1, [r0, #0x10C]
ldr r1, [r0, #0x300]
ldr r2, =0x00003fff
bic r1, r1, r2
ldr r2, =0x00011301
orr r1, r1, r2
str r1, [r0, #0x300]
ldr r1, [r0, #0x304]
ldr r2, =0x00011110
orr r1, r1, r2
str r1, [r0, #0x304]
ldr r1, =0x00000001
str r1, [r0, #0x308]
/* Set Source Clock */
ldr r1, =0x00001111 @ A, M, E, HPLL Muxing
str r1, [r0, #0x200] @ S5PC1XX_CLK_SRC0
b 200f
110:
ldr r0, =0xE010C000 @ S5PC110_PWR_CFG
/* Set OSC_FREQ value */
ldr r1, =0xf
str r1, [r0, #0x100] @ S5PC110_OSC_FREQ
/* Set MTC_STABLE value */
ldr r1, =0xffffffff
str r1, [r0, #0x110] @ S5PC110_MTC_STABLE
/* Set CLAMP_STABLE value */
ldr r1, =0x3ff03ff
str r1, [r0, #0x114] @ S5PC110_CLAMP_STABLE
ldr r0, =S5PC110_CLOCK_BASE @ 0xE0100000
/* Set Clock divider */
ldr r1, =0x14131330 @ 1:1:4:4, 1:4:5
str r1, [r0, #0x300]
ldr r1, =0x11110111 @ UART[3210]: MMC[3210]
str r1, [r0, #0x310]
/* Set Lock Time */
ldr r1, =0x2cf @ Locktime : 30us
str r1, [r0, #0x000] @ S5PC110_APLL_LOCK
ldr r1, =0xe10 @ Locktime : 0xe10 = 3600
str r1, [r0, #0x008] @ S5PC110_MPLL_LOCK
str r1, [r0, #0x010] @ S5PC110_EPLL_LOCK
str r1, [r0, #0x020] @ S5PC110_VPLL_LOCK
/* S5PC110_APLL_CON */
ldr r1, =0x80C80601 @ 800MHz
str r1, [r0, #0x100]
/* S5PC110_MPLL_CON */
ldr r1, =0x829B0C01 @ 667MHz
str r1, [r0, #0x108]
/* S5PC110_EPLL_CON */
ldr r1, =0x80600602 @ 96MHz VSEL 0 P 6 M 96 S 2
str r1, [r0, #0x110]
/* S5PC110_VPLL_CON */
ldr r1, =0x806C0603 @ 54MHz
str r1, [r0, #0x120]
/* Set Source Clock */
ldr r1, =0x10001111 @ A, M, E, VPLL Muxing
str r1, [r0, #0x200] @ S5PC1XX_CLK_SRC0
/* OneDRAM(DMC0) clock setting */
ldr r1, =0x01000000 @ ONEDRAM_SEL[25:24] 1 SCLKMPLL
str r1, [r0, #0x218] @ S5PC110_CLK_SRC6
ldr r1, =0x30000000 @ ONEDRAM_RATIO[31:28] 3 + 1
str r1, [r0, #0x318] @ S5PC110_CLK_DIV6
/* XCLKOUT = XUSBXTI 24MHz */
add r2, r0, #0xE000 @ S5PC110_OTHERS
ldr r1, [r2]
orr r1, r1, #(0x3 << 8) @ CLKOUT[9:8] 3 XUSBXTI
str r1, [r2]
/* CLK_IP0 */
ldr r1, =0x8fefeeb @ DMC[1:0] PDMA0[3] IMEM[5]
str r1, [r0, #0x460] @ S5PC110_CLK_IP0
/* CLK_IP1 */
ldr r1, =0xe9fdf0f9 @ FIMD[0] USBOTG[16]
@ NANDXL[24]
str r1, [r0, #0x464] @ S5PC110_CLK_IP1
/* CLK_IP2 */
ldr r1, =0xf75f7fc @ CORESIGHT[8] MODEM[9]
@ HOSTIF[10] HSMMC0[16]
@ HSMMC2[18] VIC[27:24]
str r1, [r0, #0x468] @ S5PC110_CLK_IP2
/* CLK_IP3 */
ldr r1, =0x8eff038c @ I2C[8:6]
@ SYSTIMER[16] UART0[17]
@ UART1[18] UART2[19]
@ UART3[20] WDT[22]
@ PWM[23] GPIO[26] SYSCON[27]
str r1, [r0, #0x46c] @ S5PC110_CLK_IP3
/* CLK_IP4 */
ldr r1, =0xfffffff1 @ CHIP_ID[0] TZPC[8:5]
str r1, [r0, #0x470] @ S5PC110_CLK_IP3
200:
/* wait at least 200us to stablize all clock */
mov r2, #0x10000
1: subs r2, r2, #1
bne 1b
mov pc, lr
internal_ram_init:
ldreq r0, =0xE3800000
ldrne r0, =0xF1500000
ldr r1, =0x0
str r1, [r0]
mov pc, lr
/*
* uart_asm_init: Initialize UART's pins
*/
uart_asm_init:
/* set GPIO to enable UART0-UART4 */
mov r0, r8
ldr r1, =0x22222222
str r1, [r0, #0x0] @ S5PC100_GPIO_A0_OFFSET
ldr r1, =0x00002222
str r1, [r0, #0x20] @ S5PC100_GPIO_A1_OFFSET
/* Check S5PC100 */
cmp r7, r8
bne 110f
/* UART_SEL GPK0[5] at S5PC100 */
add r0, r8, #0x2A0 @ S5PC100_GPIO_K0_OFFSET
ldr r1, [r0, #0x0] @ S5PC1XX_GPIO_CON_OFFSET
bic r1, r1, #(0xf << 20) @ 20 = 5 * 4-bit
orr r1, r1, #(0x1 << 20) @ Output
str r1, [r0, #0x0] @ S5PC1XX_GPIO_CON_OFFSET
ldr r1, [r0, #0x8] @ S5PC1XX_GPIO_PULL_OFFSET
bic r1, r1, #(0x3 << 10) @ 10 = 5 * 2-bit
orr r1, r1, #(0x2 << 10) @ Pull-up enabled
str r1, [r0, #0x8] @ S5PC1XX_GPIO_PULL_OFFSET
ldr r1, [r0, #0x4] @ S5PC1XX_GPIO_DAT_OFFSET
orr r1, r1, #(1 << 5) @ 5 = 5 * 1-bit
str r1, [r0, #0x4] @ S5PC1XX_GPIO_DAT_OFFSET
b 200f
110:
/*
* Note that the following address
* 0xE020'0360 is reserved address at S5PC100
*/
/* UART_SEL MP0_5[7] at S5PC110 */
add r0, r8, #0x360 @ S5PC110_GPIO_MP0_5_OFFSET
ldr r1, [r0, #0x0] @ S5PC1XX_GPIO_CON_OFFSET
bic r1, r1, #(0xf << 28) @ 28 = 7 * 4-bit
orr r1, r1, #(0x1 << 28) @ Output
str r1, [r0, #0x0] @ S5PC1XX_GPIO_CON_OFFSET
ldr r1, [r0, #0x8] @ S5PC1XX_GPIO_PULL_OFFSET
bic r1, r1, #(0x3 << 14) @ 14 = 7 * 2-bit
orr r1, r1, #(0x2 << 14) @ Pull-up enabled
str r1, [r0, #0x8] @ S5PC1XX_GPIO_PULL_OFFSET
ldr r1, [r0, #0x4] @ S5PC1XX_GPIO_DAT_OFFSET
orr r1, r1, #(1 << 7) @ 7 = 7 * 1-bit
str r1, [r0, #0x4] @ S5PC1XX_GPIO_DAT_OFFSET
200:
mov pc, lr