| |
| /* |
| * |
| * Copyright (C) 2018 Amlogic, Inc. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| * |
| * You should have received a copy of the GNU General Public License along |
| * with this program; if not, write to the Free Software Foundation, Inc., |
| * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. |
| */ |
| |
| #ifndef __G12B_W400_V1_H__ |
| #define __G12B_W400_V1_H__ |
| |
| #include <asm/arch/cpu.h> |
| |
| #define CONFIG_SYS_GENERIC_BOARD 1 |
| /* |
| #ifndef CONFIG_AML_MESON |
| #warning "include warning" |
| #endif |
| */ |
| |
| /* |
| * platform power init config |
| */ |
| #if 0 |
| #define CONFIG_PLATFORM_POWER_INIT |
| #define CONFIG_VCCK_INIT_VOLTAGE 800 // VCCK power up voltage |
| #define CONFIG_VDDEE_INIT_VOLTAGE 800 // VDDEE power up voltage |
| #define CONFIG_VDDEE_SLEEP_VOLTAGE 770 // VDDEE suspend voltage |
| #endif |
| |
| #define AML_VCCK_INIT_VOLTAGE 800 // VCCK power up voltage |
| #define AML_VDDEE_INIT_VOLTAGE 800 // VDDEE power up voltage |
| #define AML_VDDEE_SLEEP_VOLTAGE 731 // VDDEE suspend voltage |
| |
| /* configs for CEC */ |
| #if 0 |
| #define CONFIG_CEC_OSD_NAME "AML_TV" |
| #define CONFIG_CEC_WAKEUP |
| /*if use bt-wakeup,open it*/ |
| #define CONFIG_BT_WAKEUP |
| #endif |
| /* SMP Definitinos */ |
| #define CPU_RELEASE_ADDR secondary_boot_func |
| |
| /* config saradc*/ |
| #if 0 |
| #define CONFIG_CMD_SARADC 1 |
| #define CONFIG_SARADC_CH 2 |
| #endif |
| |
| /* Bootloader Control Block function |
| That is used for recovery and the bootloader to talk to each other |
| */ |
| #if 0 |
| #define CONFIG_BOOTLOADER_CONTROL_BLOCK |
| #endif |
| |
| /* Serial config */ |
| #define CONFIG_CONS_INDEX 2 |
| #define CONFIG_BAUDRATE 115200 |
| /* #define CONFIG_AML_MESON_SERIAL 1 */ |
| #if 0 |
| #define CONFIG_SERIAL_MULTI 1 |
| #endif |
| |
| /* Enable ir remote wake up for bl30 */ |
| #if 0 |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL1 0xef10fe01 //amlogic tv ir --- power |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL2 0XBB44FB04 //amlogic tv ir --- ch+ |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL3 0xF20DFE01 //amlogic tv ir --- ch- |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL4 0XBA45BD02 //amlogic small ir--- power |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL5 0xe51afb04 |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL6 0xFFFFFFFF |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL7 0xFFFFFFFF |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL8 0xFFFFFFFF |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL9 0xFFFFFFFF |
| #endif |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL1 0xef10fe01 //amlogic tv ir --- power |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL2 0XBB44FB04 //amlogic tv ir --- ch+ |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL3 0xF20DFE01 //amlogic tv ir --- ch- |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL4 0XBA45BD02 //amlogic small ir--- power |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL5 0xe51afb04 |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL6 0xFFFFFFFF |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL7 0xFFFFFFFF |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL8 0xFFFFFFFF |
| #define AML_IR_REMOTE_POWER_UP_KEY_VAL9 0xFFFFFFFF |
| |
| /*config the default parameters for adc power key*/ |
| #if 0 |
| #define CONFIG_ADC_POWER_KEY_CHAN 2 /*channel range: 0-7*/ |
| #define CONFIG_ADC_POWER_KEY_VAL 0 /*sample value range: 0-1023*/ |
| #endif |
| #define AML_ADC_POWER_KEY_CHAN 2 /*channel range: 0-7*/ |
| #define AML_ADC_POWER_KEY_VAL 0 /*sample value range: 0-1023*/ |
| |
| /* args/envs */ |
| #define CONFIG_SYS_MAXARGS 64 |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "firstboot=1\0"\ |
| "upgrade_step=0\0"\ |
| "jtag=disable\0"\ |
| "loadaddr=1080000\0"\ |
| "panel_type=lcd_1\0" \ |
| "outputmode=1080p60hz\0" \ |
| "hdmimode=1080p60hz\0" \ |
| "cvbsmode=576cvbs\0" \ |
| "display_width=1920\0" \ |
| "display_height=1080\0" \ |
| "display_bpp=16\0" \ |
| "display_color_index=16\0" \ |
| "display_layer=osd0\0" \ |
| "display_color_fg=0xffff\0" \ |
| "display_color_bg=0\0" \ |
| "dtb_mem_addr=0x1000000\0" \ |
| "fb_addr=0x3d800000\0" \ |
| "fb_width=1920\0" \ |
| "fb_height=1080\0" \ |
| "frac_rate_policy=1\0" \ |
| "usb_burning=update 1000\0" \ |
| "fdt_high=0x20000000\0"\ |
| "try_auto_burn=update 700 750;\0"\ |
| "sdcburncfg=aml_sdc_burn.ini\0"\ |
| "sdc_burning=sdc_burn ${sdcburncfg}\0"\ |
| "wipe_data=successful\0"\ |
| "wipe_cache=successful\0"\ |
| "EnableSelinux=enforcing\0" \ |
| "recovery_part=recovery\0"\ |
| "recovery_offset=0\0"\ |
| "cvbs_drv=0\0"\ |
| "lock=10001000\0"\ |
| "osd_reverse=0\0"\ |
| "video_reverse=0\0"\ |
| "active_slot=_a\0"\ |
| "boot_part=boot\0"\ |
| "reboot_mode_android=""normal""\0"\ |
| "fs_type=""rootfstype=ramfs""\0"\ |
| "initargs="\ |
| "init=/init console=ttyS0,115200 no_console_suspend earlycon=aml-uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 "\ |
| "\0"\ |
| "upgrade_check="\ |
| "echo upgrade_step=${upgrade_step}; "\ |
| "if itest ${upgrade_step} == 3; then "\ |
| "run init_display; run storeargs; run update;"\ |
| "else fi;"\ |
| "\0"\ |
| "storeargs="\ |
| "setenv bootargs ${initargs} ${fs_type} reboot_mode_android=${reboot_mode_android} logo=${display_layer},loaded,${fb_addr} vout=${outputmode},enable panel_type=${panel_type} hdmimode=${hdmimode} frac_rate_policy=${frac_rate_policy} cvbsmode=${cvbsmode} osd_reverse=${osd_reverse} video_reverse=${video_reverse} androidboot.selinux=${EnableSelinux} androidboot.firstboot=${firstboot} jtag=${jtag}; "\ |
| "setenv bootargs ${bootargs} androidboot.hardware=amlogic;"\ |
| "run cmdline_keys;"\ |
| "setenv bootargs ${bootargs} androidboot.slot_suffix=${active_slot};"\ |
| "\0"\ |
| "switch_bootmode="\ |
| "get_rebootmode;"\ |
| "if test ${reboot_mode} = factory_reset; then "\ |
| "setenv reboot_mode_android ""normal"";"\ |
| "run storeargs;"\ |
| "run recovery_from_flash;"\ |
| "else if test ${reboot_mode} = update; then "\ |
| "setenv reboot_mode_android ""normal"";"\ |
| "run storeargs;"\ |
| "run update;"\ |
| "else if test ${reboot_mode} = quiescent; then "\ |
| "setenv reboot_mode_android ""quiescent"";"\ |
| "run storeargs;"\ |
| "setenv bootargs ${bootargs} androidboot.quiescent=1;"\ |
| "else if test ${reboot_mode} = recovery_quiescent; then "\ |
| "setenv reboot_mode_android ""quiescent"";"\ |
| "run storeargs;"\ |
| "setenv bootargs ${bootargs} androidboot.quiescent=1;"\ |
| "run recovery_from_flash;"\ |
| "else if test ${reboot_mode} = cold_boot; then "\ |
| "setenv reboot_mode_android ""normal"";"\ |
| "run storeargs;"\ |
| "else if test ${reboot_mode} = fastboot; then "\ |
| "setenv reboot_mode_android ""normal"";"\ |
| "run storeargs;"\ |
| "fastboot;"\ |
| "fi;fi;fi;fi;fi;fi;"\ |
| "\0" \ |
| "storeboot="\ |
| "boot_cooling;"\ |
| "get_system_as_root_mode;"\ |
| "echo system_mode: ${system_mode};"\ |
| "if test ${system_mode} = 1; then "\ |
| "setenv fs_type ""ro rootwait skip_initramfs"";"\ |
| "run storeargs;"\ |
| "fi;"\ |
| "if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;"\ |
| "run update;"\ |
| "\0"\ |
| "factory_reset_poweroff_protect="\ |
| "echo wipe_data=${wipe_data}; echo wipe_cache=${wipe_cache};"\ |
| "if test ${wipe_data} = failed; then "\ |
| "run init_display; run storeargs;"\ |
| "if mmcinfo; then "\ |
| "run recovery_from_sdcard;"\ |
| "fi;"\ |
| "if usb start 0; then "\ |
| "run recovery_from_udisk;"\ |
| "fi;"\ |
| "run recovery_from_flash;"\ |
| "fi; "\ |
| "if test ${wipe_cache} = failed; then "\ |
| "run init_display; run storeargs;"\ |
| "if mmcinfo; then "\ |
| "run recovery_from_sdcard;"\ |
| "fi;"\ |
| "if usb start 0; then "\ |
| "run recovery_from_udisk;"\ |
| "fi;"\ |
| "run recovery_from_flash;"\ |
| "fi; \0" \ |
| "update="\ |
| /*first usb burning, second sdc_burn, third ext-sd autoscr/recovery, last udisk autoscr/recovery*/\ |
| "run usb_burning; "\ |
| "run sdc_burning; "\ |
| "if mmcinfo; then "\ |
| "run recovery_from_sdcard;"\ |
| "fi;"\ |
| "if usb start 0; then "\ |
| "run recovery_from_udisk;"\ |
| "fi;"\ |
| "run recovery_from_flash;"\ |
| "\0"\ |
| "recovery_from_sdcard="\ |
| "if fatload mmc 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;"\ |
| "if fatload mmc 0 ${loadaddr} recovery.img; then "\ |
| "if fatload mmc 0 ${dtb_mem_addr} dtb.img; then echo sd dtb.img loaded; fi;"\ |
| "wipeisb; "\ |
| "bootm ${loadaddr};fi;"\ |
| "\0"\ |
| "recovery_from_udisk="\ |
| "if fatload usb 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;"\ |
| "if fatload usb 0 ${loadaddr} recovery.img; then "\ |
| "if fatload usb 0 ${dtb_mem_addr} dtb.img; then echo udisk dtb.img loaded; fi;"\ |
| "wipeisb; "\ |
| "bootm ${loadaddr};fi;"\ |
| "\0"\ |
| "recovery_from_flash="\ |
| "setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};"\ |
| "if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then wipeisb; bootm ${loadaddr}; fi"\ |
| "\0"\ |
| "init_display="\ |
| "get_rebootmode;"\ |
| "echo reboot_mode:::: ${reboot_mode};"\ |
| "if test ${reboot_mode} = quiescent; then "\ |
| "setenv reboot_mode_android ""quiescent"";"\ |
| "run storeargs;"\ |
| "setenv bootargs ${bootargs} androidboot.quiescent=1;"\ |
| "osd open;osd clear;"\ |
| "else if test ${reboot_mode} = recovery_quiescent; then "\ |
| "setenv reboot_mode_android ""quiescent"";"\ |
| "run storeargs;"\ |
| "setenv bootargs ${bootargs} androidboot.quiescent=1;"\ |
| "osd open;osd clear;"\ |
| "else "\ |
| "setenv reboot_mode_android ""normal"";"\ |
| "run storeargs;"\ |
| "hdmitx hpd;osd open;osd clear;imgread pic logo bootup $loadaddr;bmp display $bootup_offset;bmp scale;vout output ${outputmode};"\ |
| "fi;fi;"\ |
| "\0"\ |
| "cmdline_keys="\ |
| "if keyman init 0x1234; then "\ |
| "if keyman read usid ${loadaddr} str; then "\ |
| "setenv bootargs ${bootargs} androidboot.serialno=${usid};"\ |
| "setenv serial ${usid};"\ |
| "else "\ |
| "setenv bootargs ${bootargs} androidboot.serialno=1234567890;"\ |
| "setenv serial 1234567890;"\ |
| "fi;"\ |
| "if keyman read mac ${loadaddr} str; then "\ |
| "setenv bootargs ${bootargs} mac=${mac} androidboot.mac=${mac};"\ |
| "fi;"\ |
| "if keyman read deviceid ${loadaddr} str; then "\ |
| "setenv bootargs ${bootargs} androidboot.deviceid=${deviceid};"\ |
| "fi;"\ |
| "fi;"\ |
| "\0"\ |
| "bcb_cmd="\ |
| "get_avb_mode;"\ |
| "get_valid_slot;"\ |
| "\0"\ |
| "upgrade_key="\ |
| "if gpio input GPIOAO_3; then "\ |
| "echo detect upgrade key; run update;"\ |
| "fi;"\ |
| "\0"\ |
| "irremote_update="\ |
| "if irkey 2500000 0xe31cfb04 0xb748fb04; then "\ |
| "echo read irkey ok!; " \ |
| "if itest ${irkey_value} == 0xe31cfb04; then " \ |
| "run update;" \ |
| "else if itest ${irkey_value} == 0xb748fb04; then " \ |
| "run update;\n" \ |
| "fi;fi;" \ |
| "fi;\0" \ |
| |
| |
| #define CONFIG_PREBOOT \ |
| "run bcb_cmd; "\ |
| "run factory_reset_poweroff_protect;"\ |
| "run upgrade_check;"\ |
| "run init_display;"\ |
| "run storeargs;"\ |
| "forceupdate;" \ |
| "bcb uboot-command;"\ |
| "run switch_bootmode;" |
| |
| /* #define CONFIG_ENV_IS_NOWHERE 1 */ |
| #define CONFIG_ENV_SIZE (64*1024) |
| #define CONFIG_FIT 1 |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_ANDROID_BOOT_IMAGE 1 |
| #if 0 |
| #define CONFIG_ANDROID_IMG 1 |
| #endif |
| #define CONFIG_SYS_BOOTM_LEN (64<<20) /* Increase max gunzip size*/ |
| |
| /* cpu */ |
| /* #define CONFIG_CPU_CLK 1200 //MHz. Range: 360-2000, should be multiple of 24 */ |
| |
| /* ATTENTION */ |
| /* DDR configs move to board/amlogic/[board]/firmware/timing.c */ |
| |
| #define CONFIG_NR_DRAM_BANKS 1 |
| /* ddr functions */ |
| #if 0 |
| #define CONFIG_DDR_FULL_TEST 0 //0:disable, 1:enable. ddr full test |
| #define CONFIG_CMD_DDR_D2PLL 0 //0:disable, 1:enable. d2pll cmd |
| #define CONFIG_CMD_DDR_TEST 0 //0:disable, 1:enable. ddrtest cmd |
| #define CONFIG_DDR_LOW_POWER 0 //0:disable, 1:enable. ddr clk gate for lp |
| #define CONFIG_DDR_ZQ_PD 0 //0:disable, 1:enable. ddr zq power down |
| #define CONFIG_DDR_USE_EXT_VREF 0 //0:disable, 1:enable. ddr use external vref |
| #define CONFIG_DDR4_TIMING_TEST 0 //0:disable, 1:enable. ddr4 timing test function |
| #define CONFIG_DDR_PLL_BYPASS 0 //0:disable, 1:enable. ddr pll bypass function |
| #endif |
| #define DDR_FULL_TEST 0 //0:disable, 1:enable. ddr full test |
| #define DDR_LOW_POWER 0 //0:disable, 1:enable. ddr clk gate for lp |
| #define DDR_ZQ_PD 0 //0:disable, 1:enable. ddr zq power down |
| #define DDR_USE_EXT_VREF 0 //0:disable, 1:enable. ddr use external vref |
| #define DDR4_TIMING_TEST 0 //0:disable, 1:enable. ddr4 timing test function |
| #define DDR_PLL_BYPASS 0 //0:disable, 1:enable. ddr pll bypass function |
| |
| /* storage: emmc/nand/sd */ |
| #if 0 |
| #define CONFIG_STORE_COMPATIBLE 1 |
| #endif |
| #define CONFIG_ENV_OVERWRITE |
| /* #define CONFIG_CMD_SAVEENV */ |
| /* fixme, need fix*/ |
| |
| #if (defined(CONFIG_ENV_IS_IN_AMLNAND) || defined(CONFIG_ENV_IS_IN_MMC)) && defined(CONFIG_STORE_COMPATIBLE) |
| #error env in amlnand/mmc already be compatible; |
| #endif |
| |
| /* |
| * storage |
| * |---------|---------| |
| * | | |
| * emmc<--Compatible-->nand |
| * |-------|-------| |
| * | | |
| * MTD<-Exclusive->NFTL |
| */ |
| /* axg only support slc nand */ |
| /* swither for mtd nand which is for slc only. */ |
| /* support for mtd */ |
| |
| /* #define CONFIG_AML_MTD 1*/ |
| |
| /* support for nftl */ |
| /*#define CONFIG_AML_NAND 1*/ |
| |
| #if defined(CONFIG_AML_NAND) && defined(CONFIG_MESON_NFC) |
| #error CONFIG_AML_NAND/CONFIG_MESON_NFC can not support at the sametime; |
| #endif |
| |
| #if defined(CONFIG_SPI_NAND) && defined(CONFIG_MESON_NFC) |
| #error CONFIG_SPI_NAND/CONFIG_MESON_NFC can not support at the sametime; |
| #endif |
| |
| #ifdef CONFIG_AML_MTD |
| |
| /* bootlaoder is construct by bl2 and fip |
| * when DISCRETE_BOOTLOADER is enabled, bl2 & fip |
| * will not be stored continuously, and nand layout |
| * would be bl2|rsv|fip|normal, but not |
| * bl2|fip|rsv|noraml anymore |
| */ |
| #if 0 |
| #define CONFIG_DISCRETE_BOOTLOADER |
| #endif |
| |
| #ifdef CONFIG_DISCRETE_BOOTLOADER |
| #if 0 |
| #define CONFIG_TPL_SIZE_PER_COPY 0x200000 |
| #define CONFIG_TPL_COPY_NUM 4 |
| #define CONFIG_TPL_PART_NAME "tpl" |
| /* for bl2, restricted by romboot */ |
| /* SKT 1024 pages only support 4 block, so 4 copies */ |
| #define CONFIG_BL2_COPY_NUM 4 |
| #endif |
| #endif /* CONFIG_DISCRETE_BOOTLOADER */ |
| |
| /* #define CONFIG_CMD_NAND 1 */ |
| #define CONFIG_MTD_DEVICE y |
| /* mtd parts of ourown.*/ |
| #define CONFIG_AML_MTDPART 1 |
| /* mtd parts by env default way.*/ |
| /* |
| #define MTDIDS_NAME_STR "aml_nand.0" |
| #define MTDIDS_DEFAULT "nand1=" MTDIDS_NAME_STR |
| #define MTDPARTS_DEFAULT "mtdparts=" MTDIDS_NAME_STR ":" \ |
| "3M@8192K(logo)," \ |
| "10M(recovery)," \ |
| "8M(kernel)," \ |
| "40M(rootfs)," \ |
| "-(data)" |
| */ |
| #define CONFIG_CMD_UBI |
| #define CONFIG_CMD_UBIFS |
| #define CONFIG_MTD_UBI_WL_THRESHOLD 4096 |
| #define CONFIG_MTD_UBI_BEB_LIMIT 20 |
| #define CONFIG_RBTREE |
| #define CONFIG_CMD_NAND_TORTURE 1 |
| #define CONFIG_CMD_MTDPARTS 1 |
| #define CONFIG_MTD_PARTITIONS 1 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 2 |
| #define CONFIG_SYS_NAND_BASE_LIST {0} |
| #endif |
| /* endof CONFIG_AML_MTD */ |
| /* #define CONFIG_AML_SD_EMMC 1 */ |
| #ifdef CONFIG_AML_SD_EMMC |
| #define CONFIG_GENERIC_MMC 1 |
| #define CONFIG_CMD_MMC 1 |
| #define CONFIG_CMD_GPT 1 |
| #define CONFIG_SYS_MMC_ENV_DEV 1 |
| #define CONFIG_EMMC_DDR52_EN 0 |
| #define CONFIG_EMMC_DDR52_CLK 35000000 |
| #endif |
| #define CONFIG_PARTITIONS 1 |
| #if 0 |
| #define CONFIG_SYS_NO_FLASH 1 |
| #endif |
| |
| #if defined CONFIG_AML_MTD || defined CONFIG_SPI_NAND |
| #define CONFIG_CMD_NAND 1 |
| #define CONFIG_MTD_DEVICE y |
| /* #define CONFIG_RBTREE */ |
| #define CONFIG_CMD_NAND_TORTURE 1 |
| #define CONFIG_CMD_MTDPARTS 1 |
| #define CONFIG_MTD_PARTITIONS 1 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 2 |
| #define CONFIG_SYS_NAND_BASE_LIST {0} |
| #endif |
| |
| /* vpu */ |
| #define AML_VPU_CLK_LEVEL_DFT 7 |
| |
| /* osd */ |
| #define OSD_SCALE_ENABLE |
| #define AML_OSD_HIGH_VERSION |
| |
| #if 0 |
| #define CONFIG_AML_CANVAS 1 |
| #define CONFIG_AML_OSD 1 |
| #define CONFIG_OSD_SCALE_ENABLE 1 |
| /* #define CONFIG_CMD_BMP 1 */ |
| #endif |
| |
| /* USB |
| * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard |
| * Enable CONFIG_MUSB_UDD for Device functionalities. |
| */ |
| /* #define CONFIG_MUSB_UDC 1 */ |
| /* #define CONFIG_CMD_USB 1 */ |
| |
| #define USB_PHY2_PLL_PARAMETER_1 0x09400414 |
| #define USB_PHY2_PLL_PARAMETER_2 0x927e0000 |
| #define USB_PHY2_PLL_PARAMETER_3 0xAC5F69E5 |
| |
| #define USB_G12x_PHY_PLL_SETTING_1 (0xfe18) |
| #define USB_G12x_PHY_PLL_SETTING_2 (0xfff) |
| #define USB_G12x_PHY_PLL_SETTING_3 (0x78000) |
| #define USB_G12x_PHY_PLL_SETTING_4 (0xe0004) |
| #define USB_G12x_PHY_PLL_SETTING_5 (0xe000c) |
| |
| |
| #define AML_TXLX_USB 1 |
| |
| /* UBOOT fastboot config */ |
| #if 0 |
| #define CONFIG_CMD_FASTBOOT 1 |
| #define CONFIG_FASTBOOT_FLASH_MMC_DEV 1 |
| #define CONFIG_FASTBOOT_FLASH 1 |
| #define CONFIG_USB_GADGET 1 |
| #define CONFIG_USBDOWNLOAD_GADGET 1 |
| #define CONFIG_SYS_CACHELINE_SIZE 64 |
| #define CONFIG_FASTBOOT_MAX_DOWN_SIZE 0x8000000 |
| #define CONFIG_DEVICE_PRODUCT "g12b_w400" |
| #endif |
| |
| /* UBOOT Facotry usb/sdcard burning config */ |
| /* #define CONFIG_AML_V2_FACTORY_BURN 1 //support facotry usb burning */ |
| #if 0 |
| #define CONFIG_AML_FACTORY_BURN_LOCAL_UPGRADE 1 //support factory sdcard burning |
| #define CONFIG_POWER_KEY_NOT_SUPPORTED_FOR_BURN 1 //There isnt power-key for factory sdcard burning |
| #define CONFIG_SD_BURNING_SUPPORT_UI 1 //Displaying upgrading progress bar when sdcard/udisk burning |
| #endif |
| |
| #if 0 |
| #define CONFIG_AML_SECURITY_KEY 1 |
| #define CONFIG_UNIFY_KEY_MANAGE 1 |
| #endif |
| |
| /* net */ |
| /* #define CONFIG_CMD_NET 1 */ |
| #define CONFIG_ETH_DESIGNWARE |
| #if defined(CONFIG_CMD_NET) |
| #define CONFIG_DESIGNWARE_ETH 1 |
| #define CONFIG_PHYLIB 1 |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_CMD_PING 1 |
| #define CONFIG_CMD_DHCP 1 |
| #define CONFIG_CMD_RARP 1 |
| #define CONFIG_HOSTNAME "arm_gxbb" |
| #if 0 |
| #define CONFIG_RANDOM_ETHADDR 1 /* use random eth addr, or default */ |
| #endif |
| #define CONFIG_ETHADDR 00:15:18:01:81:31 /* Ethernet address */ |
| #define CONFIG_IPADDR 10.18.9.97 /* Our ip address */ |
| #define CONFIG_GATEWAYIP 10.18.9.1 /* Our getway ip address */ |
| #define CONFIG_SERVERIP 10.18.9.113 /* Tftp server ip address */ |
| #define CONFIG_NETMASK 255.255.255.0 |
| #endif /* (CONFIG_CMD_NET) */ |
| |
| /* other devices */ |
| #if 0 |
| #define CONFIG_EFUSE 1 |
| #endif |
| #define CONFIG_SHA1 1 |
| #define CONFIG_MD5 1 |
| |
| /* commands */ |
| #if 0 |
| #define CONFIG_CMD_CACHE 1 |
| #define CONFIG_CMD_BOOTI 1 |
| #define CONFIG_CMD_EFUSE 1 |
| #define CONFIG_CMD_MEMORY 1 |
| #define CONFIG_CMD_FAT 1 |
| #define CONFIG_CMD_GPIO 1 |
| #define CONFIG_CMD_REBOOT 1 |
| #define CONFIG_CMD_ECHO 1 |
| #define CONFIG_CMD_JTAG 1 |
| #define CONFIG_CMD_AUTOSCRIPT 1 |
| #define CONFIG_CMD_MISC 1 |
| #endif |
| /* #define CONFIG_CMD_FDT 1 */ |
| |
| /*file system*/ |
| #define CONFIG_DOS_PARTITION 1 |
| #define CONFIG_EFI_PARTITION 1 |
| #if 0 |
| #define CONFIG_AML_PARTITION 1 |
| #endif |
| /* #define CONFIG_MMC 1 */ |
| #define CONFIG_FS_FAT 1 |
| #define CONFIG_FS_EXT4 1 |
| #define CONFIG_LZO 1 |
| |
| #if 0 |
| #define CONFIG_MDUMP_COMPRESS 1 |
| #endif |
| |
| /* Cache Definitions */ |
| /* #define CONFIG_SYS_DCACHE_OFF */ |
| /* #define CONFIG_SYS_ICACHE_OFF */ |
| |
| /* other functions */ |
| #if 0 |
| #define CONFIG_NEED_BL301 1 |
| #define CONFIG_NEED_BL32 1 |
| #define CONFIG_CMD_RSVMEM 1 |
| #define CONFIG_FIP_IMG_SUPPORT 1 |
| #define CONFIG_SYS_LONGHELP 1 |
| #define CONFIG_CMD_MISC 1 |
| #define CONFIG_CMD_ITEST 1 |
| #define CONFIG_CMD_CPU_TEMP 1 |
| #define CONFIG_CMD_LOADB 1 |
| #endif |
| #define CONFIG_FIP_IMG_SUPPORT 1 |
| /* #define CONFIG_SYS_MEM_TOP_HIDE 0x08000000 */ /* hide 128MB for kernel reserve */ |
| |
| #define CONFIG_CPU_ARMV8 |
| |
| /* #define CONFIG_MULTI_DTB 1 */ |
| |
| /* support secure boot */ |
| #define CONFIG_AML_SECURE_UBOOT 1 |
| |
| #if defined(CONFIG_AML_SECURE_UBOOT) |
| |
| /* for SRAM size limitation just disable NAND |
| as the socket board default has no NAND */ |
| /* #undef CONFIG_AML_NAND */ |
| |
| /* unify build for generate encrypted bootloader "u-boot.bin.encrypt" */ |
| #define CONFIG_AML_CRYPTO_UBOOT 1 |
| |
| /* unify build for generate encrypted kernel image |
| SRC : "board/amlogic/(board)/boot.img" |
| DST : "fip/boot.img.encrypt" */ |
| /* #define CONFIG_AML_CRYPTO_IMG 1 */ |
| |
| #endif /* CONFIG_AML_SECURE_UBOOT */ |
| |
| #if 0 |
| #define CONFIG_SECURE_STORAGE 1 |
| #endif |
| |
| /* build with uboot auto test */ |
| /* #define CONFIG_AML_UBOOT_AUTO_TEST 1 */ |
| |
| /* board customer ID */ |
| /* #define CONFIG_CUSTOMER_ID (0x6472616F624C4D41) */ |
| |
| #if 0 |
| #if defined(CONFIG_CUSTOMER_ID) |
| #undef CONFIG_AML_CUSTOMER_ID |
| #define CONFIG_AML_CUSTOMER_ID CONFIG_CUSTOMER_ID |
| #endif |
| #endif |
| |
| /* Choose One of Ethernet Type */ |
| #undef CONFIG_ETHERNET_NONE |
| #define ETHERNET_INTERNAL_PHY |
| #undef ETHERNET_EXTERNAL_PHY |
| |
| #if 0 |
| #define CONFIG_CMD_AML_MTEST 1 |
| #endif |
| #if defined(CONFIG_CMD_AML_MTEST) |
| #if !defined(CONFIG_SYS_MEM_TOP_HIDE) |
| #error CONFIG_CMD_AML_MTEST depends on CONFIG_SYS_MEM_TOP_HIDE; |
| #endif |
| #if !(CONFIG_SYS_MEM_TOP_HIDE) |
| #error CONFIG_SYS_MEM_TOP_HIDE should not be zero; |
| #endif |
| #endif |
| |
| #endif |
| |