Patches by Murray Jensen, 17 Jun 2003:
- Hymod board database mods: add "who" field and new xilinx chip types
- provide new "init_cmd_timeout()" function so code external to
"common/main.c" can use the "reset_cmd_timeout()" function before
entering the main loop
- add DTT support for adm1021 (new file dtt/adm1021.c; config
slightly different. see include/configs/hymod.h for an example
(requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and
CFG_DTT_ADM1021 defined)
- add new "eeprom_probe()" function which has similar args and
behaves in a similar way to "eeprom_read()" etc.
- add 8260 FCC ethernet loopback code (new "eth_loopback_test()"
function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST)
- gdbtools copyright update
- ensure that set_msr() executes the "sync" and "isync" instructions
after the "mtmsr" instruction in cpu/mpc8260/interrupts.c
- 8260 I/O ports fix: Open Drain should be set last when configuring
- add SIU IRQ defines for 8260
- allow LDSCRIPT override and OBJCFLAGS initialization: change to
config.mk to allow board configurations to override the GNU
linker script, selected via the LDSCRIPT, make variable, and to
give an initial value to the OBJCFLAGS make variable
- 8260 i2c enhancement:
o correctly extends the timeout depending on the size of all
queued messages for both transmit and receive
o will not continue with receive if transmit times out
o ensures that the error callback is done for all queued tx
and rx messages
o correctly detects both tx and rx timeouts, only delivers one to
the callback, and does not overwrite an earlier error
o logic in i2c_probe now correct
- add "vprintf()" function so that "panic()" function can be
technically correct
- many Hymod board changes
diff --git a/include/dtt.h b/include/dtt.h
index f3d95ff..a17aa67 100644
--- a/include/dtt.h
+++ b/include/dtt.h
@@ -27,9 +27,13 @@
#ifndef _DTT_H_
#define _DTT_H_
-#if defined(CONFIG_DTT_LM75) || defined(CONFIG_DTT_DS1621)
+#if defined(CONFIG_DTT_LM75) || \
+ defined(CONFIG_DTT_DS1621) || \
+ defined(CONFIG_DTT_ADM1021)
+
#define CONFIG_DTT /* We have a DTT */
+#ifndef CONFIG_DTT_ADM1021
#define DTT_COMMERCIAL_MAX_TEMP 70 /* 0 - +70 C */
#define DTT_INDUSTRIAL_MAX_TEMP 85 /* -40 - +85 C */
#define DTT_AUTOMOTIVE_MAX_TEMP 105 /* -40 - +105 C */
@@ -39,6 +43,7 @@
#ifndef CFG_DTT_HYSTERESIS
#define CFG_DTT_HYSTERESIS 5 /* 5 C */
#endif
+#endif /* CONFIG_DTT_ADM1021 */
extern int dtt_init (void);
extern int dtt_read(int sensor, int reg);
@@ -64,4 +69,37 @@
#define DTT_CONFIG 0xAC
#endif
+#if defined(CONFIG_DTT_ADM1021)
+#define DTT_READ_LOC_VALUE 0x00
+#define DTT_READ_REM_VALUE 0x01
+#define DTT_READ_STATUS 0x02
+#define DTT_READ_CONFIG 0x03
+#define DTT_READ_CONVRATE 0x04
+#define DTT_READ_LOC_HIGHLIM 0x05
+#define DTT_READ_LOC_LOWLIM 0x06
+#define DTT_READ_REM_HIGHLIM 0x07
+#define DTT_READ_REM_LOWLIM 0x08
+#define DTT_READ_DEVID 0xfe
+
+#define DTT_WRITE_CONFIG 0x09
+#define DTT_WRITE_CONVRATE 0x0a
+#define DTT_WRITE_LOC_HIGHLIM 0x0b
+#define DTT_WRITE_LOC_LOWLIM 0x0c
+#define DTT_WRITE_REM_HIGHLIM 0x0d
+#define DTT_WRITE_REM_LOWLIM 0x0e
+#define DTT_WRITE_ONESHOT 0x0f
+
+#define DTT_STATUS_BUSY 0x80 /* 1=ADC Converting */
+#define DTT_STATUS_LHIGH 0x40 /* 1=Local High Temp Limit Tripped */
+#define DTT_STATUS_LLOW 0x20 /* 1=Local Low Temp Limit Tripped */
+#define DTT_STATUS_RHIGH 0x10 /* 1=Remote High Temp Limit Tripped */
+#define DTT_STATUS_RLOW 0x08 /* 1=Remote Low Temp Limit Tripped */
+#define DTT_STATUS_OPEN 0x04 /* 1=Remote Sensor Open-Circuit */
+
+#define DTT_CONFIG_ALERT_MASKED 0x80 /* 0=ALERT Enabled, 1=ALERT Masked */
+#define DTT_CONFIG_STANDBY 0x40 /* 0=Run, 1=Standby */
+
+#define DTT_ADM1021_DEVID 0x41
+#endif
+
#endif /* _DTT_H_ */
