| ====================================================================== | |
| Changes since U-Boot 1.1.4: | |
| ====================================================================== | |
| * Add env-variable "unlock" to handle initial state of sectors | |
| (locked/unlocked). | |
| Only the U-Boot image and it's environment is protected, | |
| all other sectors are unprotected (unlocked) if flash | |
| hardware protection is used (CFG_FLASH_PROTECTION) and | |
| the environment variable "unlock" is set to "yes". | |
| Patch by Stefan Roese, 28 Feb 2006 | |
| * Update drivers/cfi_flash.c: | |
| - find_sector() called in both versions of flash_write_cfiword() | |
| Patch by Peter Pearse, 27th Feb 2006 | |
| * CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode | |
| Patch by Jose Maria Lopez, 16 Jan 2006 | |
| * Add support for AMD/Spansion Flashes in flash_write_cfibuffer | |
| Patch by Alex Bastos and Thomas Schaefer, 2005-08-29 | |
| * Changes/fixes for drivers/cfi_flash.c: | |
| We *should* check if there are any error bits if the previous call | |
| returned ERR_OK (Otherwise we will have output an error message in | |
| flash_status_check() already.) The original code would only check for | |
| error bits if flash_status_check() returns ERR_TIMEOUT. | |
| Patch by Marcus Hall, 23 Aug 2005 | |
| * Changes/fixes for drivers/cfi_flash.c: | |
| - Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c | |
| - Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c | |
| Patch by Sangmoon Kim, 19 Aug 2005 | |
| * Fixes for drivers/cfi_flash.c: | |
| - Fix wrong timeout value usage in flash_status_check() | |
| - Round write_tout up when converting to msec in flash_get_size() | |
| - Remove clearing flash status at the end of flash_write_cfibuffer() | |
| which sets Intel 28F640J3 flash back to command mode on CSB472 | |
| Patch by Tolunay Orkun, 02 July 2005 | |
| * Add GIT version information (commid ID) to untagged U-Boot versions | |
| As done in the linux kernel, the U-Boot version (U_BOOT_VERSION) | |
| of all unreleased (untagged) U-Boot images will be automatically | |
| extended upon compiletime with a part of the GIT commit ID and | |
| possibly with "dirty" if uncommited changes are detected. | |
| Here an example for the resulting version: | |
| "U-Boot 1.1.4-g3457ac18-dirty" | |
| The version is now maintained in the toplevel Makefile and the | |
| version headers are autogenerated. | |
| Patch by Stefan Roese, 9 Feb 2006 | |
| * Update default environment for INKA4x00 board. | |
| * Convert CPCI750 to use common CFI flash driver | |
| Patch by Reinhard Arlt, 8 Feb 2006 | |
| * Various changes to esd HH405 board specific files | |
| Patch by Matthias Fuchs, 07 Feb 2006 | |
| * Cleanup U-Boot boot messages on ARM. | |
| To match the U-Boot user interface on ARM platforms to the U-Boot | |
| standard (as on PPC platforms), some messages with debug character | |
| are removed from the default U-Boot build. | |
| Enable DEBUG for lib_arm/board.c to enable debug messages. | |
| New CONFIG_DISPLAY_CPUINFO and CONFIG_DISPLAY_BOARDINFO options. | |
| Patch by Stefan Roese, 24 Jan 2006 | |
| * Fix various compiler warnings on ppc4xx builds (ELDK 4.0) | |
| Patch by Stefan Roese, 18 Jan 2006 | |
| * Add VGA support (CT69000) to CPCI750 board. | |
| Insert missing __le32_to_cpu() for filesize in ext2fs_read_file(). | |
| Patch by Reinhard Arlt, 30 Dec 2005 | |
| * PMC405 and CPCI405: Moved configuration of pci resources | |
| into config file. | |
| PMC405 and CPCI2DP: Added firmware download and booting via pci. | |
| Patch by Matthias Fuchs, 20 Dec 2005 | |
| * Fix 28F256J3A support on PM520 board | |
| (without bank-switching only 32 MB can be accessed) | |
| * Fix mkimage bug with multifile images created on 64 bit systems. | |
| * Add support for 28F256J3A flash (=> 64 MB) on PM520 board | |
| * Fix compiler problem with at91rm9200dk board. | |
| Patch by Eugen Bigz, 19 Dec 2005 | |
| ====================================================================== | |
| Changes for U-Boot 1.1.4: | |
| ====================================================================== | |
| * Changes to Yellowstone & Yosemite 440EP/GR eval boards: | |
| - Changed GPIO setup to enable another address line in order to | |
| address 64M of FLASH. | |
| - Added function sdram_tr1_set to auto calculate the tr1 value for | |
| the DDR. | |
| Patch by Steven Blakeslee, 12 Dec 2005 | |
| * MPC5200: Set PCI retry counter to 0 = infinite retry; | |
| The default of 255 is too short for slow devices. | |
| Patch by Martin Nykodym, 12 Dec 2005 | |
| * Change port configuration for O2DNT (CODEC1 on PSC1). | |
| * Fix register for PCI async mode on PPC440EP | |
| Patch by Youngchul Bang, 08 Dec 2005 | |
| * Fix U-Boot linking problems (add .eh_frame segment to linker script) | |
| This segment may be required by some libgcc.a functions | |
| (like _udivdi3). | |
| * Fix DPRAM offset/size for MPC8541/8555. | |
| Simplify TQM85xx Makefile handling. | |
| * Fix data overflow (typo?) in rtc/ds1302.c | |
| * Fix U-Boot compilation for MIPS boards using ELDK 4.0 | |
| * Add support for TQM8541/8555 boards, TQM85xx support reworked: | |
| - Support for TQM8541/8555 boards added. | |
| - Complete rework of TQM8540/8560 support. | |
| - Common TQM85xx code now supports all current TQM85xx platforms | |
| (TQM8540/8541/8555/8560). | |
| - DDR SDRAM size detection added. | |
| - CAS latency default values can be overwritten by setting "serial#" | |
| to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used. | |
| If problems are detected with this non default CAS latency, | |
| the default values will be used instead. | |
| - Flash size detection added. | |
| - Moved FCC ethernet driver initialization behind TSEC driver init | |
| -> TSEC is first device. | |
| Patch by Stefan Roese, 30 Nov 2005 | |
| * Add support for AMCC 440SP, add support for AMCC Luan 440SP eval board. | |
| Patch by John Otken, 23 Nov 2005 | |
| * Changed PPC44x startup message (cpu info, speed...) to common style: | |
| On PPC44x platforms, the startup message generated in "cpu.c" only | |
| comprised the ppc type and revision but not additional information | |
| like speed etc. Those speed infos where printed in the board specific | |
| code. This new implementation now prints all CPU infos in the common | |
| cpu specific code. No board specific code is needed anymore and | |
| therefore removed from all current 44x implementations. | |
| Patch by Stefan Roese, 27 Nov 2005 | |
| * Adjust TQM834x PHY addresses for latest hardware revision. | |
| * Increase malloc arena on TQM5200 board to 256 kB. | |
| With 64 kb uniform flash sector size the old value of 128 kB was | |
| too small. | |
| * Fix miiphy global data initialization (problem on 4xx boards when | |
| no ethaddr is assigned). Initialization moved from | |
| miiphy_register() to eth_initialize(). | |
| Based on initial patch for 4xx platform by Matthias Fuchs. | |
| * Remove unnnecessary #include <linux/types.h> from include/asm-*/u-boot.h | |
| * Allow use of include/image.h and include/asm-*/u-boot.h in proprietary code. | |
| The COPYING file was extended to make clear that these files can be | |
| used in non-GPL code, too. | |
| Also, a corresponding note was placed in the headers of the affected files. | |
| * Add support for Prodrive P3P440 board: | |
| - Added onboard PPC440 DDR autodetection in cpu/ppc/sdram.c | |
| - CFG_FLASH_QUIET_TEST added to use the common CFI driver | |
| for bank autodetection | |
| Patch by Stefan Roese, 22 Nov 2005 | |
| * Change all '$(...)' variable references into '${...}' | |
| which makes the environment compatible with the hush shell. | |
| WARNING: Support for the old '$(...)' syntax will be | |
| discontinued in a later version. | |
| * Minor changes to init flags in TQM834x PCI. | |
| * Fix Bamboo DDR SDRAM initialization (problem with onboard SDRAM) | |
| Patch by Stefan Roese, 15 Nov 2005 | |
| * New PPC 405EP board added: CMS700 | |
| Added CONFIG_NET_MULTI for VOM405 board. | |
| Added reset_phy() for VOM405 board. | |
| Patch by Matthias Fuchs, 09 Nov 2005 | |
| * Updated PCI mapping for esd CPCI2DP board. | |
| Add support for error LED. | |
| Patch by Matthias Fuchs, 07 Nov 2005 | |
| * Fix MPC85xx PCI support (pci_register_hose() before pci config access) | |
| Patch by Stefan Roese, 07 Nov 2005 | |
| * Correct PPC Timebase register definitions (SPRN_TBRL...) | |
| Patch by Stefan Roese, 07 Nov 2005 | |
| * Adjust bd->bi_flashstart on Yellowstone & Yosemite to correct size | |
| Patch by Stefan Roese, 05 Nov 2005 | |
| * Additional fix for external IRQ config on Yellowstone & Yosemite | |
| Patch by Stefan Roese, 03 Nov 2005 | |
| * Add support for Ocotea pass 3 with 440GX Rev. F | |
| Patch by Stefan Roese, 01 Nov 2005 | |
| * Fix external IRQ configuration on Yellowstone & Yosemite | |
| Patch by Stefan Roese, 28 Oct 2005 | |
| * Add support for multiple PHYs. | |
| Tested on the following boards: | |
| cmcpu2 (at91rm9200/ether.c) | |
| PPChameleon (ppc4xx/4xx_enet.c) | |
| yukon (mpc8220/fec.c) | |
| uc100 (mpc8xx/fec.c) | |
| tqm834x (mpc834x/tsec.c) with EEPRO100 | |
| lite5200 (mpc5xxx/fec.c) with EEPRO100 card (drivers/eepro100.c) | |
| Main changes include: | |
| common/miiphyutil.c | |
| - miiphy_register routine was added to allow multiple PHYs to be registered | |
| - miiphy_read and miiphy_write are now defined in this file, and | |
| require additional argument (char *devname) | |
| - other miiphy_* routines also require additional device name argument | |
| ../lib_i386/board.c | |
| ../lib_ppc/board.c | |
| Calling reset_phy() was moved to be executed *after* eth_initialize(). | |
| This is necessary as now some of the implementations of reset_phy() | |
| may need to use miiphy_reset() which is not allowed before eth_initialize() | |
| as eth_initialize registers all required miiphy_* routines. | |
| Tested on IP860 and PHY initializes properly after this change. | |
| * Correct includes for flat tree builder. | |
| * Fix conflicting types (flash_write()) in trab auto_update.c. | |
| * Add PCI support for the TQM834x board. | |
| * Add missing 4xx board to MAKEALL | |
| Patch by Stefan Roese, 20 Oct 2005 | |
| * Fix conflicting types (flash_write()) in esd auto_update.c | |
| Patch by Stefan Roese, 20 Oct 2005 | |
| * Fix problem with sleep in NetConsole (use get_timer()) | |
| Patch by Stefan Roese, 20 Oct 2005 | |
| * Add NetConsole Support for AMCC eval boards | |
| Patch by Stefan Roese, 20 Oct 2005 | |
| * Fix NetConsole support on 4xx (only print eth link on 1st transfer) | |
| Patch by Stefan Roese, 18 Oct 2005 | |
| * Add fat & ext2 support to AMCC 440EP boards Yosemite & Bamboo. | |
| Fix identation on ext2ls help entry. | |
| Patch by Stefan Roese, 14 Oct 2005 | |
| * Add support for TQM834x boards. | |
| Cleanup. | |
| * Cleanup for GCC-4.x | |
| * Add documentation for Open Firmware Flat Tree and usage. | |
| Patch by Pantelis Antoniou, 13 Oct 2005 | |
| * Add missing files for Pantelis Antoniou's patch | |
| Patch by Pantelis Antoniou, 04 Sep 2005 | |
| * Fix problem in ppc4xx eth-driver without ethaddr (only without | |
| CONFIG_NET_MULTI set) | |
| Patch by Stefan Roese, 10 Oct 2005 | |
| * Fix gzip bmp support (test if malloc fails, warning when truncated). | |
| Increase CFG_VIDEO_LOGO_MAX_SIZE on HH405 board. | |
| Patch by Stefan Roese, 07 Oct 2005 | |
| * Add support for OF flat tree for the STXtc board. | |
| Patch by Pantelis Antoniou, 04 Sep 2005 | |
| * Support passing of OF flat trees to the kernel. | |
| Patch by Pantelis Antoniou, 04 Sep 2005 | |
| * Cleanup | |
| * Add support for NetSilicon NS7520 processor. | |
| Patch by Art Shipkowski, 12 May 2005 | |
| * Add support for AP1000 board. | |
| Patch by James MacAulay, 07 Oct 2005 | |
| * Eliminate hard-coded address of Ethernet transfer buffer on at91rm9200 | |
| Patch by Anders Larsen, 07 Oct 2005 | |
| The Atmel errata #11 states that the transfer buffer descriptor | |
| table must be aligned on a 16-word boundary. As it turned out, this | |
| is insufficient - it seems the table must be aligned on a boundary | |
| at least as large as the table itself (in Linux this is not an | |
| issue - the table is aligned on a PAGE_SIZE (4096) boundary). | |
| * Fixed compilation for ARM when using a (standard) hard-FP toolchain | |
| Patch by Anders Larsen, 07 Oct 2005 | |
| * Cleanup warnings for cpu/arm720t & cpu/arm1136 files. | |
| sed the linker scripts, rather than pre-process them. | |
| Patch by Peter Pearse, 07 Oct 2005 | |
| * Update make target for ARM supported boards. | |
| Use lowlevel_init() instead of platformsetup() [rename]. | |
| Patch by Peter Pearse, 06 Oct 2005 | |
| * Fix booting from serial dataflash on AT91RM9200 | |
| Patch by Peter Menzebach, 29 Aug 2005 | |
| * Add JFFS2 support for TRAB board | |
| Patch by Martin Krause, 25 Aug 2005 | |
| * Remove unnecessary dependency of netconsole on CONFIG_NET_MULTI | |
| Patch by Marcus Hall, 24 Aug 2005 | |
| * Fix the machine-id of the Cogent csb637 board | |
| Patch by Anders Larsen, 05 Oct 2005 | |
| * Complete support for the KwikByte KB920x boards | |
| Patch by Anders Larsen, 05 Oct 2005 | |
| * Set the AT91RM9200 clock to asynchronous mode | |
| Patch by Anders Larsen, 03 May 2005 | |
| * Set the AT91RM9200 clock to synchronous mode | |
| Patch by Anders Larsen, 29 Apr 2005 | |
| * Add support for Cogent csb637 | |
| Patch by Anders Larsen, 29 Apr 2005 | |
| * Fix dm9161.c initialization | |
| Patch by Anders Larsen, 29 Apr 2005 | |
| * Fix problems introduced by Patch by Steven Scholz, 02 Mar 2005 | |
| (8e2be51de8dd03c1ce4d06cbb18ad06133d47cd5) | |
| * Move dm9161.c and lxt972.c into cpu/arm920t/at91rm9200 | |
| Patch by Anders Larsen, 29 Apr 2005 | |
| * Fix device partition intialization for SystemACE disks. | |
| Patch by Stephen Williams, 28 Apr 2005 | |
| * Added support for KwikByte KB920x boards (based on AT91RM9200) | |
| Patch by Matt ?? <kb9200_dev@kwikbyte.com>, 27 Apr 2005 | |
| * Add support for S29GL064M-R3 flash chip on xsengine board | |
| Patch by Kurt Stremerch, 18 Apr 2005 | |
| * E500 update: repoint IVPR to RAM when code is relocated | |
| Patch by Kylo Ginsberg, 13 Apr 2005 | |
| * Fix loop end test in lib_generic/string.c:strswab() | |
| Patch by Andrew Dyer, October 10, 2005 | |
| Signed-off-by: Andrew Dyer <amdyer@gmail.com> | |
| * Cleanup | |
| * Update ARM Integrator boards: | |
| Correct addessing errors in platform files. | |
| Split off common core module data from Integrator header files to | |
| include/armcoremodule.h. | |
| Patch by Peter Pearse, 04 Oct 2005 | |
| * Make sure only supported compiler options are used | |
| Import "cc-option" shell function from kernel and | |
| use it to get the correct ARM GCC options for individual CPUs | |
| Patch by Peter Pearse, 30 Jun 2005 | |
| * Fix 440GR to print correct cpu revision | |
| Patch by Stefan Roese, 04 Oct 2005 | |
| * Change board message on AMCC Yosemite & Yellowstone to common style | |
| Patch by Stefan Roese, 03 Oct 2005 | |
| * Fix compiler warning | |
| * Fix FEC PHY addresses for TQM85xx boards | |
| * Fix uninitialized variable problem in hush shell | |
| Patch by Lars Rostock, 26 Sep 2005 | |
| * Undo change of f6e20fc6ca... to include/configs/trab.h | |
| (Must have been an accident?) | |
| * Add support for AT91RM9200 OHCI Controller. | |
| Patch by Eric Benard, 07 Apr 2005 | |
| * Update ARM mach-types.h | |
| Patch by Eric Benard, 07 Apr 2005 | |
| * Add support for MP2USB board. | |
| Patch by Eric Benard, 07 Apr 2005 | |
| * Add board support for armadillo HT1070 | |
| Patch by Rowel Atienza, 06 Apr 2005 | |
| * Second Ethernet address enabled for MPC885ADS and MPC8272ADS. | |
| Patch by Vitaly Bordug, 30 Mar 2005 | |
| * Add iopset command on mpc8xx | |
| Patch by Daniel Eisenhut, 25 Mar 2005 | |
| * Add support for MII in eepro100 driver. | |
| Patch by Gleb Natapov, 21 Mar 2005 | |
| * Fixes to the Lubbock (PXA 25x) support: | |
| - Resolve the FIXME with respect to saving the u-boot environment. | |
| - Make the default load address land in real memory. | |
| - Fix lan91c96 SMC_{in,out}{b,w,l}() macros | |
| Patch by David Brownell, 10 Mar 2005 | |
| * Add Barco Streaming Video Card (SVC) and Sample Compress Network (SCN) board | |
| Patch by Marc Leeman, 04 Mar 2005 | |
| * OMAP242x H4 board update | |
| - fix for ES2 differences. | |
| - switch to using the cfi_flash driver. | |
| - fix SRAM build address. | |
| - fix for GP device operation. | |
| - unlock SRAM for GP devices. | |
| - display more device information. | |
| - fix potential deadlock in omap24xx_i2c driver. | |
| - fix DLL load values to match dpllout*1 operation. | |
| - fix 2nd chip select init for combo DDR device. | |
| - add support for CFI Intel 28F256L18 on H4 board. | |
| Patch by Richard Woodruff, 03 Mar 2005 | |
| * Fix formating in include/asm-arm/arch-at91rm9200/AT91RM9200.h | |
| Patch by Steven Scholz, 02 Mar 2005 | |
| * Fix typo in eth.c | |
| Patch by Ara Avanesyan, 24 Feb 2005 | |
| * Remove unneeded #include <malloc.h> | |
| Patch by Ladislav Michl, 22 Feb 2005 | |
| * Add cramfs support for m68k | |
| Patch by Zachary Landau, 21 Feb 2005 | |
| * Update ep8260: Fix flash timeouts; improve clock resolution for faster UARTs | |
| Patch by Jeff Angielski, 21 Feb 2005 | |
| * Fix au1x00_serial baud rate calculation: | |
| remove hardcoded cpu clock divisor and use register instead; | |
| round up instead of truncate | |
| Patch by Andrew Dyer, 15 Feb 2005 | |
| * Add Xilinx Spartan3 family FPGA support | |
| Patch by Kurt Stremerch, 14 Feb 2005 | |
| * Fix drivers/cfi_flash.c: use info->reset_cmd instead of FLASH_CMD_RESET | |
| Patch by Zachary Landau, 11 Feb 2005 | |
| * Fix VOH405 Support | |
| Patch by Matthias Fuchs, 25 Sep 2005 | |
| * Added support for PCI bridge on MPC8272ADS | |
| Patch by Vitaly Bordug, Feb 09 2005 | |
| * Update multicore CM9XX support for Integrator AP to allow booting from flash | |
| Patch by Jean-Paul Saman, 8 Feb 2005 | |
| * Fix strswab() to reliably find end of string | |
| Patch by Andrew Dyer, 08 Feb 2005 | |
| * Fix typos in include/ppc440.h | |
| Patch by Andrew E Mileski, 04 Feb 2005 | |
| * Add Vibren (was Accelent) PXA255 IDP Support | |
| Patch by Cliff Brake, 04 Feb 2005 | |
| * Fix tools/bmp_logo.c using incorrect offset to pixel data | |
| Patch by Andrew Dyer, 31 Jan 2005 | |
| * Add ARM946E cpu and core module targets; remap memory to 0x00000000 | |
| Patch by Peter Pearse, 2 Feb 2005 | |
| * Fix error handling in tools/env/fw_env.c | |
| Patch by Ara Avanesyan, 01 Feb 2005 | |
| * Fix MGT5100 PSC baudrate calculation | |
| Patch by Sebastian Schau, 27 Jan 2005 | |
| * OMAP242x fix for GP device booting | |
| - Add SRAM unlock for GP devices. | |
| - Change DDR DLL unlock value to allow DPLLout*1 operation. | |
| Patches by Richard Woodruff, 21 Jan 2005: | |
| * Add support for AMD's Pb1x00 eval board; | |
| add MII routines to the au1x00 ethernet driver; | |
| add USB ohci driver (work in progress) | |
| Patch by Thomas Sailer, 20 Jan 2005 | |
| * Update omap5912osk board | |
| Use drivers/cfi_flash.c instead of private flash driver; | |
| Remove hardcoded personalized settings from omap5912osk.h; | |
| Fix spacing with (RO) marks in 'flinfo' output. | |
| Patch by Michael Bendzick, 14 Jan 2005 | |
| * Fix warnings for PCI code on ixp | |
| Patch by Joe <lgxue@yahoo.com>, 13 Jan 2005 | |
| * virtex2 fix for bogus download error messages | |
| The virtex2 FPGA download code watches for init going active during | |
| a download of config data as an error condition. init also goes | |
| active after a configuration is finished in concert with the done | |
| signal. So far, the code does not check for done active until all | |
| of the configuration data is sent. If configuration data has a few | |
| extra pad bytes at the end, this would cause an error message even | |
| though the download had suceeded. | |
| NOTE: virtex2 slave serial and spartan2 versions may still have the | |
| same problem. | |
| Patch by Andrew Dyer, 12 Jan 2005 | |
| * Optimize flash_make_cmd in drivers/cfi_flash.c for little endian | |
| Fix "WARNING: flash_make_cmd: unsuppported LittleEndian mode" | |
| message when probing for nonexistent flash in little endian mode. | |
| As a side effect more efficient and smaller code is generated, | |
| which is always a Good Thing (TM). | |
| Patch by Ladislav Michl, 24 Sep 2005 | |
| * Update for TFTP using a fixed UDP port | |
| Use the approved environment variable names. Added "tftpdstp" to | |
| allow ports other than 69 per Tolunay Orkun's recommendation. | |
| Patch by Jerry Van Baren, 12 Jan 2005 | |
| * Allow to force TFTP to use a fixed UDP port | |
| (Add a configuration option CONFIG_TFTP_PORT and optional env | |
| variable tftpport) | |
| Patch by Jerry Van Baren, 10 Jan 2005 | |
| * Fix ethernet timeouts on dbau1550 and other au1x00 systems | |
| Patch by Leif Lindholm, 29 Dec 2004 | |
| * Cleanup: fix broken builds | |
| * Fix PHY address argument passing with mii info command | |
| Patch by Andrew Dyer, 28 Dec 2004 | |
| * Cleanup (PPC4xx is AMCC now) | |
| * esd CPCI2DP board added | |
| Patch by Matthias Fuchs, 22 Sep 2005 | |
| * esd PMC405 board updated | |
| Patch by Matthias Fuchs, 22 Sep 2005 | |
| * Add SM501 support to HH405 board. | |
| Add support for gzip compressed bmp's (CONFIG_VIDEO_BMP_GZIP). | |
| Add support for eeprom write-enable (CFG_EEPROM_WREN). | |
| Patch by Stefan Roese, 22 Sep 2005 | |
| * Fix autonegotiation in tsec ethernet driver | |
| Patch by Stefan Roese, 21 Sep 2005 | |
| * Fix bug in auto_update (trab board) | |
| Patch by Martin Krause, 16 Sep 2005 | |
| * Fix computation of framebuffer palette for 8bpp LCD bitmaps | |
| Patch by Francesco Mandracci, 16 Sep 2005 | |
| * Update configuration for INKA4x0 board | |
| * Update configuration for PM854 board | |
| Based on patch by R. Loeffl, 20 Jul 2005 | |
| * Add PCI support to TQM8540 and TQM8560 boards | |
| Patch by Stefan Roese, 15 Sep 2005 | |
| * Update AMCC Yosemite to get a consistent setup for all AMCC eval | |
| boards (baudrate, environment...). Flash driver fixed. | |
| Patch by Stefan Roese, 15 Sep 2005 | |
| * Fix problem in 440GP ethernet driver (ebony). Add support for 2nd | |
| ethernet port on ebony. | |
| Patch by Stefan Roese, 7 Sep 2005 | |
| * Added support for mtddevnum and mtddevname variables (mtdparts command) | |
| * Change default console baud rate for stxxtc board | |
| * Add I2C support to TQM8540 and TQM8560 boards (EEPROM, RTC, LM75-DTT). | |
| Patch by Stefan Roese, 31 Aug 2005 | |
| * Fix default command set (don't include CFG_CMD_DISPLAY command) | |
| Patch by Pantelis Antoniou, 02 Sep 2005 | |
| * Cleanup | |
| * Enable SM712 driver support for HMI1001 board. | |
| * Fix problems with ld version 2.16 (dot outside sections problem) | |
| Pointed out by Gerhard Jaeger, 31 Aug 2005; | |
| cf. http://sourceware.org/ml/binutils/2005-08/msg00412.html | |
| * Prepare U-Boot for gcc-4.x: fix global data pointer initialization | |
| * Adjust CS3 timings on HMI1001 board for dot matrix display under Linux | |
| * Add keyboard and dot matrix display support for HMI1001 board. | |
| * Prepare U-Boot for gcc-4.x | |
| * Fixed Bamboo port to enable running without DDR-DIMM | |
| (Bamboo has also 64MB onboard DDR) | |
| Patch by Stefan Roese, 24 Aug 2005 | |
| * Merged 405gp_enet.c and 440gx_enet.c to generic 4xx_enet.c | |
| now handling all 4xx cpu's | |
| Patch by Stefan Roese, 16 Aug 2005 | |
| * Fix make dependencies for at91rm9200 and ks8695 cpus | |
| Patch by Steven Scholz, 23 Aug 2005 | |
| * Add JFFS2 support for TQM5200 board | |
| * Add esd cpci5200 and pf5200 boards | |
| Patch by Reinhard Arlt, 22 Aug 2005 | |
| * Fix sysclock for TQM8540 and TQM8560 boards | |
| Patch by Martin Krause, 25 Jul 2005 | |
| * Initialize serial# and ethaddr from manufacturer data in EEPROM on CMC-PU2 | |
| Patch by Martin Krause, 08 Jun 2005 | |
| * Add new board specific commands for TQM5200/STK52XX | |
| - Sound commands (beep, wav, sound) | |
| - Test commands (led, can, backlight, rs232) | |
| Patch by Martin Krause, 02 May 2005 | |
| * Change main clock on CMC-PU2 board from 207 MHz to 179 MHz | |
| because of a bug in the AT91RM9200 CPU PLL | |
| Patch by Martin Krause, 22 Apr 2005 | |
| * Add automatic HW detection for another CMC_PU2 variant | |
| Patch by Martin Krause, 20 Apr 2005 | |
| * Remove CONFIG_AT91RM9200DK in CMC-PU2 configuration | |
| Patch by Martin Krause, 19 Apr 2005 | |
| * Fix initialization problem on TQM5200 without SM501 | |
| Patch by Martin Krause, 08 Apr 2005 | |
| * Add RTC support for STK52XX.200 | |
| Patch by Martin Krause, 07 Apr 2005 | |
| * Add support for IFM o2dnt board | |
| * Enable PCI on hmi1001 board | |
| * Fix return values of the jffs2 commands ls/fsload/fsinfo, | |
| so we can use them to, e.g., check the existence of a file with | |
| "if ls foo; then this; else that; fi" in the hush shell | |
| Patch by Andreas Engel, 16 August 2005 | |
| * Coding style cleanup | |
| * Add support for Silicon Turnkey eXpress XTc (mpc87x/88x) board. | |
| Patch by Dan Malek and Pantelis Antoniou, 15 Aug 2005 | |
| * Check return value of malloc in 440gx_enet.c | |
| Patch by Travis B. Sawyer, 18 Jul 2005 | |
| * Add Sandburst Metrobox and Sandburst Karef board support packages. | |
| Second serial port on 440GX now defined as a system device. | |
| Add 'Short Etch' code for Cicada PHY within 440gx_enet.c | |
| Patch by Travis B. Sawyer, 12 Jul 2005 | |
| ====================================================================== | |
| Changes for U-Boot 1.1.3: | |
| ====================================================================== | |
| * Minor code cleanup | |
| * Add forgotten new fils from latest VoiceBlue update | |
| * Make bootretry feature work with hush shell. | |
| Caveat: this currently *requires* CONFIG_RESET_TO_RETRY to be set, too. | |
| Patch by Andreas Engel, 19 Jul 2005 | |
| * Update Hymod Board Database PHP code in "tools" directory | |
| Patch by Murray Jensen, 01 Jul 2005 | |
| * Make "tr" command use POSIX compliant; export HOSTOS make variable | |
| Patch by Murray Jensen, 30 Jun 2005 | |
| * Fix Murray Jensen's mail address. | |
| Patch by Murray Jensen, 30 Jun 2005 | |
| * Preserve PHY_BMCR during a soft reset. | |
| Patch by Carl Riechers, 24 Jun 2005 | |
| * VoiceBlue update: eeprom tool can also store firmware version now. | |
| eeprom.bin is runable by jumping at load address. | |
| Patch by Ladislav Michl, 23 May 2005 | |
| * Move the AT91RM9200DK to the ARM Systems list. | |
| Patch by Anders Larsen, 26 Apr 2005 | |
| * Eliminate calls of ARM libgcc.a helper functions _divsi3 and _modsi3 | |
| Patch by Anders Larsen, 26 Apr 2005 | |
| * measure_gclk() is needed when DEBUG is enabled | |
| Patch by Bryan O'Donoghue, 25 Apr 2005 | |
| * Add UPD-Checksum code, fix problem in net.c (return instead of break) | |
| Patch by Reinhard Arlt, 12 Aug 2005 | |
| * esd PCI405 board updated | |
| Patch by Matthias Fuchs, 28 Jul 2005 | |
| * esd WUH405 and DU405 board updated | |
| Patch by Matthias Fuchs, 27 Jul 2005 | |
| * Fix problem in cmd_nand.c (only when defined CFG_NAND_SKIP_BAD_DOT_I) | |
| Patch by Matthias Fuchs, 4 May 2005 | |
| * Update AMCC Yosemite to get a consistent setup for all AMCC eval | |
| boards (baudrate, environment...). Flash driver fixed. | |
| Patch by Stefan Roese, 11 Aug 2005 | |
| * Changed AMCC Bubinga (405EP) configuration to support 2nd eth port | |
| Patch by Stefan Roese, 11 Aug 2005 | |
| * Add NAND FLASH support for AMCC Bamboo 440EP eval board | |
| Patch by Stefan Roese, 11 Aug 2005 | |
| * Add configuration for IFM AEV FIFO board. | |
| Minor coding style cleanup. | |
| * Add configuration for IFM SPI eval board | |
| * Fix CompactFlash problem on HMI1001 board | |
| * Make new "mtdparts" code build with older compilers | |
| Patch by Andrea Scian, 09 Aug 2005 | |
| * Changed CONFIG_440_GX, CONFIG_440_EP and CONFIG_440_GR options to | |
| CONFIG_44GX, CONFIG_440EP and CONFIG_440GR for a consistent design | |
| with the 405 defines and the linux kernel defines. | |
| Patch by Stefan Roese, 08 Aug 2005 | |
| * Fix compiler warnings with older GCC versions | |
| * Add common (with Linux) MTD partition scheme and "mtdparts" command | |
| Old, obsolete and duplicated code was cleaned up and replace by the | |
| new partitioning method. There are two possible approaches now: | |
| The first one is to define a single, static partition: | |
| #undef CONFIG_JFFS2_CMDLINE | |
| #define CONFIG_JFFS2_DEV "nor0" | |
| #define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF /* use whole device */ | |
| #define CONFIG_JFFS2_PART_SIZE 0x00100000 /* use 1MB */ | |
| #define CONFIG_JFFS2_PART_OFFSET 0x00000000 | |
| The second method uses the mtdparts command line option and dynamic | |
| partitioning: | |
| /* mtdparts command line support */ | |
| #define CONFIG_JFFS2_CMDLINE | |
| #define MTDIDS_DEFAULT "nor1=zuma-1,nor2=zuma-2" | |
| #define MTDPARTS_DEFAULT "mtdparts=zuma-1:-(jffs2),zuma-2:-(user)" | |
| Command line of course produces bigger images, and may be inappropriate | |
| for some targets, so by default it's off. | |
| * Fix build problems for PM856 Board | |
| * Fix sign extension bug in 'fpga loadb' command; | |
| make 'fpga loadb' always print the file header info | |
| Patch by Andrew Dyer, 11 Jan 2005 | |
| * Fix errors that occur when accessing SystemACE CF | |
| Patch by Jeff Angielski, 09 Jan 2005 | |
| * Document switching between U-Boot and PlanetCore on RPXlite | |
| by Sam Song, 24 Dec 2004 | |
| * Fix PowerQUICC II mask detection. | |
| Patch by Eugene Surovegin, 20 Dec 2004 | |
| * Add support for Altera NIOS DK1C20 board | |
| Patch by Shlomo Kut, 13 Dec 2004 | |
| * Add support for ep8248 board | |
| Patch by Yuli Barcohen, 12 Dec 2004 | |
| Minor code cleanup. | |
| * Fix baudrate setting for KGDB on MPC8260 | |
| Patch by HoJin, 11 Dec 2004 | |
| * Fix 'mii help' text formatting | |
| Patch by Cory Tusar, 10 Dec 2004 | |
| * Fix return code of NFS command | |
| Patch by Hiroshi Ito, 11 Dec 2004 | |
| * Fix typo | |
| * Fix compiler warnings in cpu/ppc4xx/usbdev.c | |
| Patch by Steven Blakeslee, 04 Aug 2005 | |
| * Add support for AMCC Bamboo PPC440EP eval board | |
| Patch by Stefan Roese, 04 Aug 2005 | |
| * Patch by Jon Loeliger | |
| Fix style issues primarily in 85xx and 83xx boards. | |
| - C++ comments | |
| - Trailing white space | |
| - Indentation not by TAB | |
| - Excessive amount of empty lines | |
| - Trailing empty lines | |
| * Patch by Ron Alder, 11 Jul 2005 | |
| Add Xianghua Xiao and Lunsheng Wang's support for the | |
| GDA MPC8540 EVAL board. | |
| * Patch by Eran Liberty | |
| Add support for the Freescale MPC8349ADS board. | |
| * Patch by Jon Loeliger, 25 Jul 2005 | |
| Move the TSEC driver out of cpu/mpc85xx as it will be shared | |
| by the upcoming mpc83xx family as well. | |
| * Patch by Jon Loeliger, 05 May 2005 | |
| Implemented support for MPC8548CDS board. | |
| Added DDR II support based on SPD values for MPC85xx boards. | |
| This roll-up patch also includes bugfies for the previously | |
| published patches: | |
| DDRII CPO, pre eTSEC, 8548 LBIU, Andy's TSEC, eTSEC 3&4 I/O | |
| * Patch by Jon Loeliger, 10 Feb 2005 | |
| Add config option CONFIG_HAS_FEC calling out 8540 FEC features. | |
| * Patch by Jon Loeliger, Kumar Gala, 08 Feb 2005 | |
| For MPC85xxCDS: | |
| Adds Relaxed Timing TRLX bit to FLASH ORx regs to allow | |
| for faster flash parts. | |
| Add documentation for BR/OR for FLASH. | |
| * Patch by Jon Loeliger 08 Feb 2005 | |
| Determine L2 Cache size dynamically on 85XX boards. | |
| * Patch by Jon Loeliger, Kumar Gala 08 Feb 2005 | |
| - Convert the CPM2 based functionality to use new CONFIG_CPM2 | |
| option rather than a myriad of CONFIG_MPC8560-like variants. | |
| Applies to MPC85xx and MPC8260 boards, includes stxgp3 and sbc8560. | |
| Eliminates the CONFIG_MPC8560 option entirely. Distributes the | |
| new CONFIG_CPM2 option to each 8260 board. | |
| * Add support for MicroSys PM856 board | |
| Patch by Josef Wagner, 03 Aug 2005 | |
| * Minor fixes to PM854 board | |
| Patch by Josef Wagner, 03 Aug 2005 | |
| * Adjust configuration of XENIAX board | |
| (chip select and GPIO required for USB operation) | |
| * Fix typos in cpu/85xx/start.S which caused DataTLB exception to be | |
| routed to the Watchdog handler | |
| Patch by Eugene Surovegin, 18 Jun 2005 | |
| * (re)enabled scsi commands do_scsi() and do_scsiboot() | |
| Patch by Denis Peter, 06 Dec 2004 | |
| * Fix endianess problem in TFTP / NFS default filenames | |
| Patch by Hiroshi Ito, 06 Dec 2004 | |
| * Ignore broadcast status bit in received frames in 8260 FCC ethernet | |
| loopback test code | |
| Patch by Murray Jensen, 18 Jul 2005 | |
| * Fix typo in mkconfig script (used == instead of =) | |
| Patch by Murray Jensen, 18 Jul 2005 | |
| * Cleanup build problems on 64 bit build hosts | |
| * Update MAINTAINERS file | |
| * Patch by Stefan Roese, 01 Aug 2005: | |
| - Major cleanup for AMCC eval boards Walnut, Bubinga, Ebony, Ocotea | |
| (former IBM eval board). Please see "doc/README.AMCC-eval-boards-cleanup" | |
| for details. | |
| - Sycamore (PPC405GPr) eval board added (Walnut port is extended | |
| to run on both 405GP and 405GPr eval boards). | |
| * Patch by Steven Blakeslee, 27 Jul 2005: | |
| - Add support for AMCC PPC440EP/GR. | |
| - Add support for AMCC Yosemite PPC440EP eval board. | |
| - Add support for AMCC Yellowstone PPC440GR eval board. | |
| * Minor fixes for PPChameleon Board: | |
| - fix alignment of NAND size | |
| - make code do what the comment says | |
| * Implement h/w sector protection status synchronization at boot. | |
| The code is provided for, and was tested on, the Yukon/Alaska | |
| and PM520 boards only. | |
| A bug in flash_real_protect() for the Yukon board was fixed by | |
| adding a function that tells if two banks are on one flash chip. | |
| * Fix sysmon POST problem: check I2C error codes | |
| This fixes a problem of displaying bogus voltages when the voltages | |
| are so low that the I2C devices start failing while the rest of the | |
| system keeps running. | |
| * Patch by Cedric Vincent, 6 Jul 2005: | |
| Fix CFG_CMD_SETGETDCR handling in "common/cmd_dcr.c" | |
| * Patch by Jon Loeliger, 20 Jul 2005: | |
| Add missing PCI IO port definitions. | |
| * Add CompactFlash support for HMI1001 board. | |
| * Adjust printed board ID for LWMON board. | |
| * Fix low-level OHCI transfers for ARM920t and MPC5xxx | |
| * Add new argument format for flash commands to allow for usage like | |
| "erase $(addr) +$(filesize)", i. e. a size argument can be used and | |
| U-Boot will automaticially find the end of the corresponding sector. | |
| * Patch by Stefan Roese, 5 Jul 2005: | |
| Update uc100 board PHY setup | |
| * Patch by Stefan Roese, 1 Jul 2005: | |
| Fix PHY address for CATcenter board (now correct!) | |
| * Patch by Stefan Roese, 30 Jun 2005: | |
| Fix PHY addresses for PPChameleon and CATcenter boards | |
| Change MAINTAINER for most esd boards | |
| * Patch by Detlev Zundel, 30 Jun 2005: | |
| Fix LCD logo for lwmon board which got lost in the merge of 8xx and PXA LCD code | |
| * Fix baudrate calculation problem on MPC5200 systems | |
| * Add EEPROM and RTC support for HMI1001 board | |
| * Patch by Detlev Zundel, 20 Jun 2005: | |
| Fix initialization of low active GPIO pins on inka4x0 board | |
| * Enable redundant environment, disable HW flash protection of | |
| HMI1001 board | |
| * Patch by Travis Sawyer, 10 Jun 2005: | |
| Initialize allocated dev and private hw structures | |
| after their respective allocation in 440gx_enet.c | |
| * Patch by Steven Scholz, 10 Jun 2005: | |
| Fix byteorder problems with second argument of "bootm" with | |
| standalone images; | |
| * Add support for HMI1001 board | |
| * Disable "date" and "sntp" commands on TQM866M | |
| * Fix watchdog reset problems on LWMON board | |
| * Patch by Juergen Selent, 17 May 2005: | |
| Add support for Funkwerk VoVPN gateway module. | |
| * Cleanup debug code for MPC8220 FEC driver | |
| * Extend burst mode RAM test program to take a loop count | |
| (0 = infinite) | |
| * Use CONFIG_DRIVER_KS8695ETH to enable KS8695 ethernet driver on | |
| those boards that use it. | |
| * Patches by Greg Ungerer, 19 May 2005: | |
| - add support for the KS8695P (ARM 922 based) CPU | |
| - add support for the OpenGear CM4008, CM4116 and CM4148 boards | |
| * Patch by Steven Scholz, 19 May 2005: | |
| Add support for CONFIG_SERIAL_TAG on ARM boards | |
| * Add PCI support for Sorcery board. | |
| Code cleanup (especially Sorcery / Alaska / Yukon serial driver). | |
| * Fix compile problems caused by new burst mode SDRAM test; | |
| make port pins to trigger logic analyzer configurable | |
| * Fix timer handling on MPC85xx systems | |
| * Fix debug code in omap5912osk flash driver | |
| * Add support for MPC8247 based "IDS8247" board. | |
| * Add support for 2 x TSEC interfaces on the TQM8540 board. | |
| * On LWMON we must use the watchdog to reset the board as the CPU | |
| genereated HRESET pulse is too short to reset the external | |
| circuitry. | |
| * Add test tool to exercise SDRAM accesses in burst mode | |
| (as standalone program, MPC8xx/PowerPC only) | |
| * Increase CFG_MONITOR_LEN for Rattler board to match actual code | |
| size. | |
| * Major upate of JFFS2 code; now in sync with snapshot of MTD CVS of | |
| March 13, 2005); new configuration option CONFIG_JFFS2_LZO_LZARI | |
| added to support LZO and LZARI compression modes (undefined by | |
| default). | |
| * Fix problem with symbolic links in JFFS2 code. | |
| * Use linker ASSERT statement to prevent undetected overlapping of | |
| sections on PPChameleon board; other boards might use this, too. | |
| * Patch by Stefan Roese, 03 May 2005: | |
| Update for P3G4 | |
| Fix problems in cmd_universe.c | |
| * Patch by Matthias Fuchs, 03 May 2005: | |
| Added missing variable declaration in cmd_nand.c | |
| Modified CFG_PCI_PTM1MS in configs/PLU405.h to map 128MB ram | |
| * Fix INKA4x0: use CS1 as gpio_wkup_6 output | |
| * Fix bug in the SDRAM initialization code for canmb, IceCube and | |
| PM520 boards. | |
| Fix PHY address for canmb board. | |
| * Cleanup serial console baudrate calculation on AT91RM9200; | |
| get rid of obsolete CFG_AT91C_BRGR_DIVISOR definition | |
| * Patch by Matthias Fuchs, 18 Apr 2005: | |
| Make PCI target address spaces on PMC405 and CPCI405 boards | |
| configurable via environment variables | |
| * Auto-size RAM on canmb board. | |
| * Add support for canmb board | |
| * Patch by Stefan Roese, 13 Apr 2005: | |
| Update for esd apc405 | |
| * Fixes for TQM8560 board: | |
| - fix clock rates | |
| - remove debug messages | |
| - fix flash sector protection | |
| * Patch by Steven Scholz, 07 Apr 2005: | |
| Add i2c_reg_write() and i2c_reg_write() for at91rm9200 I2C | |
| * Patches by Steven Scholz, 07 Apr 2005: | |
| Fix compiler warning in altera.c | |
| Fix warning in cpu/arm920t/at91rm9200/i2c.c | |
| * Patch by Ladislav Michl, 06 Apr 2005: | |
| Fix voiceblue configuration. | |
| * Patch by Stefan Roese, 06 Apr 2005: | |
| Updates for OCOTEA board: | |
| - Changed U-Boot size from 512kByte to 256kByte | |
| - Fixed flash driver to support boot from soldered user flash | |
| - Added README for switch from PIBS firmware to U-Boot | |
| * Patch by Travis Sawyer, 05 Apr 2005: | |
| - Change timer frequency for ppc 440 from 10 ms to 1 ms. | |
| Problem found by Andrew Wozniak. | |
| * Patch by Steven Scholz, 06 Apr 2005: | |
| - creating SoC subdir for Atmel AT91RM9200 cpu/arm920t/at91rm9200 | |
| - moving code out of cpu/at91rm9200 into cpu/arm920t/at91rm9200 | |
| * Patches by Robert Whaley, 29 Nov 2004: | |
| - update the pxa-regs.h file for PXA27x chips | |
| - add PXA27x based ADSVIX board | |
| - add support for MMC on PXA27x processors | |
| * Patch by Andrew E. Mileski, 28 Nov 2004: | |
| Fix PPC4xx SPD SDRAM detection bug | |
| * Patch by Hiroshi Ito, 26 Nov 2004: | |
| Fix logic of "test -z" and "test -n" commands | |
| * Patch by Ladislav Michl, 05 Apr 2005: | |
| Add support for VoiceBlue board. | |
| * Patch by Ladislav Michl, 05 Apr 2005: | |
| Fix netboot_common() prototypes. | |
| * Patch by Steven Scholz, 05 Apr 2005: | |
| Use i.MX watchdog timer for reset_cpu() | |
| * Patch by Steven Scholz, 05 Apr 2005: | |
| Move reset_cpu() out of cpu/arm920t/start.S into the SoC specific | |
| subdirectories cpu/arm920t/imx/ and cpu/arm920t/s3c24x0/ | |
| (now in interupts.c) | |
| * Add support for MPC8220 based "sorcery" board. | |
| * Add support for TQM8560 board. | |
| * Add FEC support for TQM8540 board. | |
| Interfaces are named as follows: "ENET1" - TSEC2, "ENET2" - FEC | |
| * Patch by Martin Krause, 04 Apr 2005: | |
| Update default configuration for CMC_PU2 board. | |
| * Patch by Steven Scholz, 04 Apr 2005: | |
| - remove all references to CONFIG_INIT_CRITICAL for ARM based boards | |
| - introduce two new configuration options instead: | |
| CONFIG_SKIP_LOWLEVEL_INIT and CONFIG_SKIP_RELOCATE_UBOOT | |
| * Patch by Steven Scholz, 04 Apr 2005: | |
| Make sure that MDIO clock does not exceed 2.5 MHz on AT91 | |
| * Fix timer code for ARM systems: make sure that udelay() does not | |
| reset timers so it's save to use udelay() in timeout code. | |
| * Patch by Mathias Küster, 23 Nov 2004: | |
| add udelay support for the mcf5282 cpu | |
| * Patch by Tolunay Orkun, 16 November 2004: | |
| fix incorrect onboard Xilinx CPLD base address | |
| * Patch by Jerry Van Baren, 08 Nov 2004: | |
| - Add low-boot option for MPC8260ADS board (if lowboot is selected, | |
| the jumper for the HRCW source should select flash. If lowboot is | |
| not selected, the jumper for the HRCW source should select the | |
| BCSR. | |
| - change default load base address to 0x00400000 | |
| * Patch by Yuli Barcohen, 08 Nov 2004: | |
| Add support for Analogue & Micro Rattler boards. | |
| Tested on Rattler8248. | |
| * Patch by Andre Renaud, 08 Nov 2004: | |
| Fix watchdog support in common/lcd.c | |
| * Patch by Marc Leeman, 05 Nov 2003: | |
| Enable all 4 PCMBRW buffers for the MPC8245 processor since the CPU | |
| bug only affects the XPC8245 processors | |
| * Patches by Josef Wagner, 29 Oct 2004: | |
| - Add support for MicroSys CPU87 board | |
| - Add support for MicroSys PM854 board | |
| * Patch by Jian Zhang, 02 Nov 2004: | |
| Add 16-bit NAND support | |
| * Patch by Scott McNutt, 01 Nov 2004: | |
| Add missing NIOS/NIOS2 support for "iminfo" command | |
| * Patch by Detlev Zundel, 29 Oct 2004: | |
| Add missing NIOS/NIOS2 support for "mkimage" tool. | |
| * Patch by David Adair, 27 Oct 2004: | |
| Add missing 440GX SDRAM Controller reset | |
| * Patch by Steven Scholz, 25 Oct 2004: | |
| Declare reset_cpu() in include/common.h instead locally | |
| * Patch by Yusdi Santoso, 22 Oct 2004: | |
| - Add support for HIDDEN_DRAGON board | |
| - fix endianess problem in driver/rtl1839.c | |
| * Patch by Allen Curtis, 21 Oct 2004: | |
| support multiple serial ports | |
| * Patch by Richard Klingler, 03 Apr 2005: | |
| Add call to eth_halt() in net/net.c when called functions fail | |
| after eth_init() has been called. | |
| * Patch by Sam Song, 3 April 2005: | |
| - Update README.Netconsole | |
| - Update README | |
| * Prepare for SoC rework of ARM code: | |
| - rename CONFIG_BOOTBINFUNC into CONFIG_INIT_CRITICAL | |
| - rename memsetup into lowlevel_init (function name and source files) | |
| Patch by Steven Scholz, 03 Apr 2005: | |
| - create SoC specific directories include/asm-arm/arch-imx and | |
| include/asm-arm/arch-s3c24x0 | |
| * Fix problems with SNTP support; | |
| enable SNTP support in some boards. | |
| * Patches by Martin Krause, 01 Apr 2005: | |
| - Fix flash erase timeout on CMC_PU2 | |
| - Add automatic HW detection for CMC_PU2 and CMC_BASIC | |
| * Patch by Steven Scholz, 13 March 2005: | |
| fix cache enabling for AT91RM9200 | |
| * Patch by Masami Komiya, 30 Mar 2005: | |
| add SNTP support and expand time server and time offset fields of | |
| DHCP support. See doc/README.SNTP | |
| * Patch by Steven Scholz, 13 Dec 2004: | |
| Fix bug in at91rm920 ethernet driver | |
| * Patch by Steven Scholz, 13 Dec 2004: | |
| Remove duplicated code by merging memsetup.S files for | |
| at91rm9200 boards into one cpu/at91rm9200/lowlevel.S | |
| * Patch by Detlev Zundel, 31 Mar 2005: | |
| Cleanup duplicate definition of overwrite_console() | |
| * Update TQM5200 configuration; | |
| prepare for Rev. 200 starter kit boards | |
| * Patch by Scott McNutt, 21 Oct 2004: | |
| Add support for Nios-II EPCS Controller core. | |
| * Patch by Scott McNutt, 20 Oct 2004: | |
| Nios-II cleanups: | |
| - Add sysid command (Nios-II only). | |
| - Locate default exception trampoline at proper offset. | |
| - Implement I/O routines (readb, writeb, etc) | |
| - Implement do_bootm_linux | |
| * Patches by Martin Krause, 22 Mar 2005: | |
| - use TQM5200_auto as MAKEALL target for TQM5200 systems | |
| - add support for SM501 graphics controller | |
| - add support for graphic console on TQM5200 | |
| - add support for TQM5200 Rev 200 | |
| - cleanup, fix typo in include/configs/TQM5200.h | |
| * Patch by Manfred Baral, 17 Mar 2005: | |
| Fix typo | |
| * Fix RTC configuration for PPChameleon board | |
| * Cleanup, fix typo in include/configs/TQM5200.h | |
| * Patch by Stefan Roese, 16 Mar 2005: | |
| Update for esd auto_update and hh405 board | |
| * Adapt for U-Boot image size (new features enabled) on TQM5200 | |
| * Update code for TQM8540 board (and 85xx in general): | |
| - Change the name of the Ethernet driver: MOTO ENET -> ENET | |
| - Reformat boot messages | |
| - Enable redundant environment | |
| - Replace the -O2 optimization flag with -mno-string | |
| * Patch by David Brownell, 10 Mar 2005: | |
| Restore copyright statements in OHCI drivers. | |
| * Add support for TQM8540 board | |
| * Patch by Detlev Zundel, 14 Mar 2005: | |
| NC650: changed NAND flash addressing to using UPMB | |
| * Patch by Stefan Roese, 14 Mar 2005: | |
| Update for esd voh405 fpga image | |
| * INKA4x0: Allow initialization of LCD backlight dimming from | |
| "brightness" environment variable. | |
| * Add port initialization for digital I/O on INKA4x0 | |
| * Patch by Stefan Roese, 01 Mar 2005: | |
| Update for esd boards dp405 and hub405 | |
| * Fix get_partition_info() parameter error in all other calls | |
| (common/cmd_ide.c, common/cmd_reiser.c, common/cmd_scsi.c). | |
| * Enable USB and IDE support for INKA4x0 board | |
| * Patch by Andrew Dyer, 28 Feb 2005: | |
| fix ext2load passing an incorrect pointer to get_partition_info() | |
| resulting in load failure for devices other than 0 | |
| * Add support for SRAM and 2 x Quad UARTs on INKA4x0 board | |
| * Cleanup USB and partition defines | |
| * Add support for ext2 filesystems and image timestamps to TQM5200 board | |
| * Add reset code for Coral-P on INKA4x0 board | |
| * Patch by Martin Krause, 28 Jun 2004: | |
| Update for TRAB board. | |
| * Fix some missing "volatile"s in MPC5xxx FEC driver | |
| * Fix cirrus voltage detection (for CPC45) | |
| * Fix byteorder problem in usbboot and scsiboot commands. | |
| * Patch by Cajus Hahn, 04 Feb 2005: | |
| - don't insist on leading '/' for filename in ext2load | |
| - set default partition to useful value (1) in ext2load | |
| * Patch by Andrew Dyer, 08 Jan 2005: | |
| fix wrong return codes in ext2 code | |
| * Removed '--no-warn-mismatch' option from Makefile. This option | |
| makes 'ld' to overlook binary objects compatibility. | |
| * Moved $(PLATFORM_LIBS) from the library group (--start-group ... | |
| --end-group) outside of the group. This will make 'ld' to do | |
| _multiple_ search in the library group when resolving symbol | |
| references and do only a _single_ seach in libgcc.a after the group | |
| search. | |
| * Fix stability problems on CPC45 board again. | |
| * Make image detection for diskboot / usbboot / scsiboot more robust | |
| (also check header checksum) | |
| * Update CPC45 board configuration. | |
| * Add USB and PCI support for INKA4x0 board | |
| * Fix IDE stability problems on CPC45 board (needs 2 x EIEIO). | |
| * Code cleanup | |
| * Patch by Robin Getz, 13 Oct 2004: | |
| Add standalone application to change SMC91C111 MAC addresses, | |
| see examples/README.smc91111_eeprom | |
| * Patch by Xiaogeng (Shawn) Jin, 12 Oct 2004: | |
| Fix Flash support for ARM Integrator CP. | |
| * Patch by Richard Woodruff, 10 Jan 2005: | |
| Update support for OMAP2420 (ARM11) and H4 board: | |
| o clean up and add new types to H4 memory probe code. | |
| o fix to work with internal boot. | |
| o added PRCM config III operation. | |
| o fix marginal flash timings. | |
| o add revison ATAG usage. | |
| o enable voltage scaling at power chip. | |
| o fix compile error for i2c. | |
| * Fix network problem (error when receiving multiple ARP packets) | |
| * Patch by Daniel Poirot, 12 Oct 2004: | |
| Add support for Wind River sbc405 board | |
| * Patch by Rainer Brestan, 12 Oct 2004: | |
| Make examples/Makefile more robust | |
| * Patch by Sam Song, 11 October 2004: | |
| - Add RESET/PREBOOT/AUTOBOOT support for RPXlite_DW board | |
| - Adjust CPU:BUS frequency ratio 1:1 when core frequency | |
| less than 50MHz | |
| * Patch by Sam Song, 10 Oct 2004: | |
| Fix a parameter error in run_command() in main.c | |
| * Patch by Richard Woodruff, 01 Oct 2004: | |
| add support for the TI OMAP2420 processor and its H4 reference | |
| board | |
| * Patch by Christian Pellegrin, 24 Sep 2004: | |
| Added support for NE2000 compatible (DP8390, DP83902) NICs. | |
| * Patch by Leif Lindholm, 23 Sep 2004: | |
| add support for the AMD db1550 board | |
| * Patch by Travis Sawyer, 15 Sep 2004: | |
| Add CONFIG_SERIAL_MULTI support for ppc4xx, | |
| update README.serial_multi | |
| * Patches by David Snowdon, 07 Sep 2004: | |
| - add u-boot.hex target in the top level Makefile | |
| - add support for the UNSW/NICTA PLEB 2 board (pleb2) | |
| - use -mtune=xscale and -march=armv5 options for PXA | |
| * Patch by Florian Schlote, 08 Sep 2004: | |
| Add support for SenTec-COBRA5272-board (Coldfire). | |
| * Patch by Gleb Natapov, 07 Sep 2004: | |
| mpc824x: set PCI latency timer to a sane value | |
| (is 0 after reset). | |
| * Patch by Kurt Stremerch, 03 Sep 2004: | |
| Add bitstream configuration option for fpga command (Xilinx only). | |
| * Patch by Kurt Stremerch, 03 Sep 2004: | |
| Add Xilinx Spartan2E family FPGA support | |
| * Patch by Jeff Angielski, 02 Sep 2004: | |
| Add Added support for H2 revision of the EP8260 board. | |
| Fixed formatting for some of the EP8260 related source files. | |
| * Patch by Jon Loeliger, 02 Sep 2004: | |
| Reset monitor size back to 256 so environment can be written | |
| to flash on MPC85xx ADS and CDS releases. | |
| * Patch by Paolo Broggini, 02 Sep 2004: | |
| Make BSS clearing on ARM systems more robust | |
| * Patch by Yue Hu and Joe, 01 Sep 2004: | |
| - add PCI support for ixp425; | |
| - add EEPRO100 suppor tfor ixdp425 board. | |
| * Fix problem with protected sector detection in driver/cfi_flash.c | |
| ====================================================================== | |
| Changes for U-Boot 1.1.2: | |
| ====================================================================== | |
| * Code cleanup, mostly for GCC-3.3.x | |
| * Cleanup confusing use of CONFIG_ETH*ADDR - ust his only to | |
| pre-define a MAC address; use CONFIG_HAS_ETH* to enable support for | |
| additional ethernet addresses. | |
| * Cleanup drivers/i82365.c - avoid duplication of code | |
| * Fix bogus "cannot span across banks" flash error message | |
| * Code cleanup | |
| * Add support for CompactFlash for the CPC45 Board. | |
| * Fix problems with CMC_PU2 flash driver. | |
| * Cleanup: | |
| - avoid trigraph warning in fs/ext2/ext2fs.c | |
| - rename UC100 -> uc100 | |
| * Add support for UC100 board | |
| * Patch by Stefan Roese, 16 Dez 2004: | |
| - ext2fs support added | |
| - Tundra universe support added | |
| - Coldfire MCF5249 support added (no preloader needed!) | |
| - MCF5249 board TASREG added | |
| - PPC boards added: APC405, CPCI405DT, CPCI750, G2000, HH405, | |
| VOM405, WUH405 | |
| - some esd boards updated | |
| - memory commands "mdc" and "mwc" added for cyclic read/write | |
| (CONFIG_MX_CYCLIC, see README for further description) | |
| * Add support for INKA4X0 board | |
| * Patch by Steven Scholz, 12 Dec 2004: | |
| Fix typo in AT91 memory setup. | |
| * Patch by Martin Krause, 27 Oct 2004: | |
| - add support for "STK52xx" board (including PS/2 multiplexer) | |
| - add hardware detection for TQM5200 | |
| * Clean up CMC PU2 flash driver | |
| * Update MAINTAINERS file | |
| * Fix bug in MPC823 LCD driver | |
| * Fix udelay() on AT91RM9200 for delays < 1 ms. | |
| * Enable long help on CMC PU2 board; | |
| fix reset issue; | |
| increase CPU speed from 179 to 207 MHz. | |
| * Fix smc91111 ethernet driver for Xaeniax board (need to handle | |
| unaligned tail part specially). | |
| * Update for AT91RM9200DK and CMC_PU2 boards: | |
| - Enable booting directly from flash | |
| - fix CMC_PU2 flash driver | |
| * Fix mkimage usage message | |
| * Map SRAM on NC650 board | |
| * Work around for Ethernet problems on Xaeniax board | |
| * Patch by TsiChung Liew, 23 Sep 2004: | |
| - add support for MPC8220 CPU | |
| - Add support for Alaska and Yukon boards | |
| * Fix configuration for ERIC board (needs more room) | |
| * Adjust MIPS compiler options at run-time depending on tools version | |
| ("-march=4kc -mtune=4kc -Wa,-mips_allow_branch_to_undefined" for new, | |
| "-mcpu=4kc" for old tools) | |
| * Add passing of the command line and memory size information to the | |
| kernel on xaeniax board. | |
| * Enable NAND flash support for NC650 board. | |
| * Patch by Thomas Lange 07 Oct 2004: | |
| Updated README for DBAu1x00 boards to match current status | |
| * Patch by Philippe Robin, 28 Sept 2004: | |
| Fix Flash support for Versatile. | |
| * Patch by Roger Blofeld, 16 Sep 2004: | |
| Fix timeout for DHCP command retry | |
| * Patch by Pantelis Antoniou, 14 Sep 2004: | |
| Fix early serial hang when CONFIG_SERIAL_MULTI is defined. | |
| * Patch by Pantelis Antoniou, 14 Sep 2004: | |
| Kick watchdog when bz-decompressing | |
| * Fix CFG_HZ problems on AT91RM9200 systems | |
| [Remember: CFG_HZ should be 1000 on ALL systems!] | |
| * Patch by Gridish Shlomi, 30 Aug 2004: | |
| - Add support to revA version of PQ27 and PQ27E. | |
| - Reverted MPC8260ADS baudrate back to original 115200 | |
| * Patch by Hojin, 17 Sep 2004: | |
| Fix typo in cfi_flash.c | |
| * Patch by Mark Jonas, 09 September 2004: | |
| mtest's data line test (with CFG_ALT_MEMTEST set) returned a wrong | |
| error message | |
| * Patch by Mark Jonas, 31 August 2004: | |
| Added option CFG_XLB_PIPELINING to enable XLB pipelining. This | |
| improves FTP performance for MPC5200 systems. Enabled for IceCube | |
| by default. | |
| * Patch by Michael Bendzick, 30 Aug 2004: | |
| - Improve platform.S code for omap1510inn that detects whether code | |
| is running from SDRAM or not. Patch allows SDRAM to be configured | |
| if code is running out of SRAM at 0x20000000. | |
| * Patch by Frederick Klatt, 30 Aug 2004: | |
| Add support for the Wind River SBC8540/SBC8560 boards | |
| * Configure SX1 board to use drivers/cfi_flash.c | |
| * Patches by Michael Bendzick, 30 Aug 2004: | |
| - Configure omap1510inn board to use drivers/cfi_flash.c | |
| - Make drivers/cfi_flash.c protect environment and redundant | |
| environment. | |
| * Patch by Steven Scholz, 23 Jun 2004: | |
| - Add script (tools/img2brec.sh) to programm U-Boot into | |
| (Synch)Flash using the Bootstrap Mode of the MC9328MX1/L | |
| * Patches by Scott McNutt, 24 Aug 2004: | |
| - Add support for Altera Nios-II processors. | |
| - Add support for Psyent PCI-5441 board. | |
| - Add support for Psyent PK1C20 board. | |
| * Patches by Jon Loeliger, 24 Aug 2004: | |
| - Add support for the MPC8541 and MPC8555 CDS boards | |
| - Cleanup eth?addr handling: make dependent on CONFIG_ETH?ADDR | |
| - Convert MPC85xxADS to use common CFI flash driver | |
| - Fix PCI window on MPC85xx; remove unneeded PCI initialization | |
| from board_early_init_f() | |
| - Provide SW workaround for PCI initialization on 85xx CDS | |
| * Patches by George G. Davis, 24 Aug 2004: | |
| - Enable ramdisk/initrd tagged param support for omap1610h2_config | |
| - Remove static network setup defaults from mx1ads_config | |
| - update ARM boards to use constants from mach-types.h | |
| * Patch by Gary Jennejohn, 04 Oct 2004: | |
| - fix I2C on at91rm9200 | |
| - add support for Ricoh RS5C372A RTC | |
| * Patch by Gary Jennejohn, 01 Oct 2004: | |
| - add support for CMC PU2 board | |
| - add support for I2C on at91rm9200 | |
| * Patch by Gary Jennejohn, 28 Sep 2004: | |
| fix baudrate handling on at91rm9200 | |
| * Patch by Yuli Barcohen, 22 Aug 2004: | |
| - remove ZPC.1900 board-specific flash driver; | |
| switch the port to generic CFI driver; | |
| - port clean-up | |
| * Patch by Hinko Kocevar, 21 Aug 2004: | |
| Add calc_fbsize() function used with VIDEOLFB_TAG on TRAB | |
| * Clean up tools/bmp_logo.c to not add trailing white space | |
| * Patch by Hinko Kocevar, 21 Aug 2004: | |
| - Group common framebuffer functions in common/lcd.c | |
| - Group common framebuffer macros and #defines in include/lcd.h | |
| - Provide calc_fbsize() for video ATAG | |
| * Patch by Sam Song, 21 August 2004: | |
| - Fix a typo in README | |
| - Align "(RO)" output for "flinfo" after "protect on" | |
| - Add RESET support for RPXlite_DW board; adjust CPU:BUS frequency | |
| ratio 1:1 when core frequency less than 50MHz | |
| * Patches by Hinko Kocevar, 21 Aug 2004: | |
| - fix some "use of label at end of compound statement" warnings | |
| - Define type of LCD panel on lubbock board if CONFIG_LCD is used | |
| * Patch by Steven Scholz, 16 Aug 2004: | |
| - Introducing the concept of SoCs "./cpu/$(CPU)/$(SOC)" | |
| - creating subdirs for SoCs ./cpu/arm920t/imx and ./cpu/arm920t/s3c24x0 | |
| - moving SoC specific code out of cpu/arm920t/ into cpu/arm920t/$(SOC)/ | |
| - moving drivers/s3c24x0_i2c.c and drivers/serial_imx.c out of drivers/ | |
| into cpu/arm920t/$(SOC)/ | |
| * Patches by Sean Chang, 09 Aug 2004: | |
| - Added support for both 8 and 16 bit mode access to System ACE CF | |
| through MPU. | |
| - Fixed missing System ACE CF device during get FAT partition info | |
| in fat_register_device function. | |
| - Enabled System ACE CF support on ML300. | |
| * Patch by Sean Chang, 09 Aug 2004: | |
| Synch defines for saveenv and do_saveenv functions so they get | |
| compiled under the same statement. | |
| * Patch by Sean Chang, 09 Aug 2004: | |
| - Added I2C support for ML300. | |
| - Added support for ML300 to read out its environment information | |
| stored on the EEPROM. | |
| - Added support to use board specific parameters as part of | |
| U-Boot's environment information. | |
| - Updated MLD files to support configuration for new features | |
| above. | |
| * Patches by Travis Sawyer, 05 Aug 2004: | |
| - Remove incorrect bridge settings for eth group 6 | |
| - Add call to setup bridge in ppc_440x_eth_initialize | |
| - Fix ppc_440x_eth_init to reset the phy only if its the | |
| first time through, otherwise, just check the phy for the | |
| autonegotiated speed/duplex. This allows the use of netconsole | |
| - only print the speed/duplex the first time the phy is reset. | |
| * Patch by Shlomo Kut, 29 Mar 2004: | |
| Add support for MKS Instruments "Quantum" board | |
| * Fix build problem with Cogent boards; | |
| avoid using <asm/byteorder.h> when using the host compiler | |
| * Patch by Ganapathi C, 04 Aug 2004: | |
| Fix NFS timeout issue | |
| * Patch by Yuli Barcohen, 19 Jul 2004: | |
| - Fix host tools building in Cygwin environment | |
| - Fix header files search order for host tools | |
| * Patch by Tom Armistead, 19 Jul 2004: | |
| Fix kgdb.S support for 74xx_75x cpu | |
| * Patch by Jon Loeliger, 15 Jul 2004: | |
| Fix MPC85xx I2C driver | |
| * Fix problems with CDROM drive as slave device on Lite5200 IDE bus. | |
| * Patch by Stephen Williams, 15 July 2004 | |
| Set the PCI class code for JSE board as part of PCI interface setup | |
| * Patch by Michael Bendzick, 15 Jul 2004: | |
| Fix problem with writes with odd sizes in drivers/cfi_flash.c when | |
| CFG_FLASH_USE_BUFFER_WRITE is set | |
| * Patch by Yuli Barcohen, 13 Jul 2004: | |
| Allow clock setting on MPC866/MPC885 series chips according to | |
| environment variable `cpuclk' | |
| * Patch by Yuli Barcohen, 20 Apr 2004: | |
| Remove unnecessary redefine of CPM_DATAONLY_SIZE for MPC826x | |
| * Patch by Vincent Dubey, 24 Sep 2004: | |
| Add support for xaeniax board | |
| * Add comment about non-GPL character of standalone applications to | |
| COPYING file | |
| * Fix FEC ethernet problem on NSCU board. | |
| * Patch by Gary Jennejohn, 09 Sep 2004: | |
| allow to use USART1 as console port on at91rm9200dk boards | |
| * Patch by Stefan Roese, 16 Sep 2004: | |
| Update AR405 board. | |
| * Fix SysClk handling for PPChameleon and CATcenter boards | |
| * Patch by Detlev Zundel, 08 Sep 2004: | |
| Update etags build target | |
| * Improve NetConsole support: add support for broadcast destination | |
| address and buffered input. | |
| * Cleanup compiler warnings for GCC 3.3.x and later | |
| * Fix problem in cmd_jffs2.c introduced by CFG_JFFS_SINGLE_PART patch | |
| * Add support for IDS "NC650" board | |
| * Add automatic update support for LWMON board | |
| * Clear Block Lock-Bits when erasing flash on LWMON board. | |
| * Fix return code of "fatload" command | |
| * Enable MSDOS/VFAT filesystem support for LWMON board | |
| * Patch by Martin Krause, 03 Aug 2004: | |
| change timing for SM501 graphics controller on TQM5200 module | |
| * Patch by Mark Jonas, 13 July 2004: | |
| - Total5200 LCD now run in little endian mode. Endianess conversion | |
| is done in hardware. | |
| - Removed last reference to "console" environment variable. | |
| * Patches by Lars Munch, 12 Jul 2004: | |
| - move at45.c to board/at91rm9200dk/ since this is at91rm9200dk | |
| board specific | |
| - split out the LXT971A PHY from ns_9750_eth.h | |
| - split the dm9161 phy part out of at91rm9200_ether.c | |
| * Patch by Andreas Engel, 12 Jul 2004: | |
| Replaced hardcoded PL011 clock frequency with config variable. | |
| Fixed wrong CONFIG_CMD_DFL doc. | |
| * Patch by Thomas Viehweger, 09 Jun 2004: | |
| make it possible to remove chpart when there is only one partition | |
| * Add support for console over UDP (compatible to Ingo Molnar's | |
| netconsole patch under Linux) | |
| * Patch by Jon Loeliger, 16 Jul 2004: | |
| - support larger DDR memories up to 2G on the PC8540/8560ADS and | |
| STXGP3 boards | |
| - Made MPC8540/8560ADS be 33Mhz PCI by default. | |
| - Removed moldy CONFIG_RAM_AS_FLASH, CFG_FLASH_PORT_WIDTH_16 | |
| and CONFIG_L2_INIT_RAM options. | |
| - Refactor Local Bus initialization out of SDRAM setup. | |
| - Re-implement new version of LBC11/DDR11 errata workarounds. | |
| - Moved board specific PCI init parts out of CPU directory. | |
| - Added TLB entry for PCI-1 IO Memory | |
| - Updated README.mpc85xxads | |
| * Patch by Sascha Hauer, 28 Jun: | |
| - add generic support for Motorola i.MX architecture | |
| - add support for mx1ads, mx1fs2 and scb9328 boards | |
| * Patches by Marc Leeman, 23 Jul 2004: | |
| - Add define for the PCI/Memory Buffer Configuration Register | |
| - corrected comments in cpu/mpc824x/cpu_init.c | |
| * Add support for multiple serial interfaces | |
| (for example to allow modem dial-in / dial-out) | |
| * Patch by Stefan Roese, 15 Jul 2004: | |
| cpu/ppc4xx/sdram.c rewritten now using get_ram_size() | |
| * Fix NSCU config; add ethernet wakeup code. | |
| * Add link for preloader for Motorola Coldfire to README.m68k | |
| * Patch by Michael Bendzick, 12 Jul 2004: | |
| fix output formatting in drivers/cfi_flash.c | |
| * Patch by Mark Jonas, 02 Jul 2004: | |
| Fix lowboot (again) on MPC5xxx | |
| * Patch by Curt Brune, 07 Jul 2004: | |
| relocate exception vectors on arm720t if needed | |
| * Patch by George G. Davis, 06 Jul 2004: | |
| - update mach-types.h to latest arm.linux.org.uk master list | |
| - Set correct OMAP1610 bi_arch_number for build target | |
| * Patch by Curt Brune, 06 Jul 2004: | |
| evb4510: add support for timer interrupt; cleanup | |
| * Patch by Dan Poirot, 06 Jul 2004: | |
| Fix sbc8260 environment variables | |
| * Cleanup redundand "console" environment variable | |
| * Patch by Mark Jonas, 05 Jul 2004: | |
| add support for the Total5100's and Total5200's LCD screen | |
| * Patches by Dan Eisenhut, 01 Jul 2004: | |
| - README fixes. | |
| - Move doc2000.h include to prevent compiler warning on some boards | |
| * Patch by Mark Jonas, 01 Jul 2004: | |
| Added support for Total5100 and Total5200 (Rev.1 and Rev.2) | |
| MGT5100 and MPC5200 based Freescale platforms. | |
| * Patch by Philippe Robin, 01 Jul 2004: | |
| Add initialization for Integrator and versatile board files. | |
| * Patch by Hinko Kocevar, 01 Jun 2004: | |
| Fix VFD FB allocation, add LCD FB allocation on ARM | |
| * Patch by Martin Krause, 30 Jun 2004: | |
| Add support for TQM5200 board | |
| * Patch by Martin Krause, 29 Jun 2004: | |
| Add loopw command: infinite write loop on address range | |
| * Patches by Yasushi Shoji, 29 Jun 2004: | |
| - add empty include/asm-microblaze/processor.h | |
| - add to CREDITS and MAINTAINERS | |
| - add gd initialization | |
| - add MicroBlaze and SUZAKU board to MAKEALL script | |
| - add reset support for SUZAKU | |
| - add flush_cache() for MicroBlaze | |
| - add CFG_FLASH_SIZE to include/configs/suzaku.h since we have fixed | |
| size flash memory on SUZAKU | |
| * Patch by Prakash Kumar, 27 Jun 2004: | |
| Add support for the PXA250 based Intrinsyc Cerf board. | |
| * Patch by Yasushi Shoji, 27 Jun 2004: | |
| fix comment in include/common.h | |
| * Rename SBC8560 into sbc8560 for consistency | |
| * Patch by Daniel Poirot, 24 Jun 2004: | |
| Add support for Wind River's sbc8240 board | |
| * Patches by Yasushi Shoji, 26 Jun 2004: | |
| - drivers/serial_xuartlite.c: fix "return 0" in void function | |
| - add microblaze support to mkimage tool | |
| * Patch by Fred Klatt, 25 Jun 2004: | |
| Add support for WindRiver's sbc8560 board | |
| * Patch by Nicolas Lacressonniere, 24 Jun 2004 | |
| Small Bugs fixes for "at91rm9200dk" board: | |
| - Timing modifications for SPI DataFlash access | |
| - Fix NAND flash detection bug | |
| * Patch by Nicolas Lacressonniere, 24 Jun 2004: | |
| Add Support for Flash AT49BV6416 for AT91RM9200DK board | |
| * Patch by Jon Loeliger, 17 June 2004: | |
| Completion of the 8540ADS/8560ADS updates: | |
| Fix some PCI and Rapid I/O memory maps, | |
| Initialize both TSEC 1 and 2, | |
| Initialize SDRAM | |
| Update MAINTAINER for 85xx boards and README.mpc85xxads | |
| * Patch by Yuli Barcohen, 16 Jun 2004: | |
| Remove obsolete AdderII port which was superseded by unified | |
| AdderII/Adder87x port | |
| * Patch by Ladislav Michl, 16 Jun 2004: | |
| Fix gcc-3.3.3 warnings for smc91111.c | |
| * Patch by Stefan Roese, 02 Jul 2004: | |
| - Fix bug in 405 ethernet driver; allocated data not cleared! | |
| - Fix problem in 405 i2c driver; don't try to print without console! | |
| * Patch by Paul Ruhland, 11 Jun 2004: | |
| Remove debug code from 'board/lpd7a40x/flash.c' | |
| * Patch by Andrea Marson, 11 Jun 2004: | |
| Update for PPChameleon board: | |
| - support for SysClk @ 25MHz | |
| - support for Silicon Motion SM712 VGA controller | |
| - some clean ups | |
| * Patches by Richard Woodruff, 10 Jun 2004: | |
| - fix problems with examples/stubs.c for GCC >= 3.4 | |
| - fix problems with gd initialization | |
| * Patch by Curt Brune, 17 May 2004: | |
| - Add support for Samsung S3C4510B CPU (ARM7tdmi based SoC) | |
| - Add support for ESPD-Inc. EVB4510 Board | |
| * Patch by Marc Leeman, 11 May 2004: | |
| Fix for MPC8245 - reading PPC Memory from another device with the | |
| PPC as PCI target device corrupts data due to interenal hardware | |
| buffering. | |
| * Fix "cls" command when used with splash screen | |
| * Increase NFS download timeout (now 1 min - 10 sec is to short for a | |
| slow download of a big image) | |
| * Add "cls" function to MPC823 LCD driver so we can reinitialize the | |
| display even after showing a bitmap | |
| * Patch by Josef Wagner, 04 Jun 2004: | |
| - DDR Ram support for PM520 (MPC5200) | |
| - support for different flash types (PM520) | |
| - USB / IDE / CF-Card / DiskOnChip support for PM520 | |
| - 8 bit boot rom support for PM520/CE520 | |
| - Add auto SDRAM module detection for MicroSys CPC45 board (MPC8245) | |
| - I2C and RTC support for CPC45 | |
| - support of new flash type (28F160C3T) for CPC45 | |
| * Fix flash parameters passed to Linux for PPChameleon board | |
| * Remove eth_init() from lib_arm/board.c; it's done in net.net.c. | |
| * Patch by Paul Ruhland, 10 Jun 2004: | |
| fix support for Logic SDK-LH7A404 board and clean up the | |
| LH7A404 register macros. | |
| * Patch by Matthew McClintock, 10 Jun 2004: | |
| Modify code to select correct serial clock on Sandpoint8245 | |
| * Patch by Robert Schwebel, 10 Jun 2004: | |
| Add support for Intel K3 strata flash. | |
| * Patch by Thomas Brand, 10 Jun 2004: | |
| Fix "loads" command on DK1S10 board | |
| * Patch by Yuli Barcohen, 09 Jun 2004: | |
| Add support for 8MB flash SIMM and JFFS2 file system on | |
| Motorola FADS board and its derivatives (MPC86xADS, MPC885ADS). | |
| * Patch by Yuli Barcohen, 09 Jun 2004: | |
| Add support for Analogue&Micro Adder87x and the older AdderII board. | |
| * Patch by Ming-Len Wu, 09 Jun 2004: | |
| Add suppport for MC9328 (Dargonball) CPU and Motorola MX1ADS board | |
| * Patch by Sam Song, 09 Jun 2004: | |
| - Add support for RPXlite_DW board | |
| - Update FLASH driver for 4*AM29DL323DB90VI | |
| - Add option configuration of CFG_ENV_IS_IN_NVRAM on RPXlite_DW board | |
| * Patch by Mark Jonas, 08 June 2004: | |
| - Make MPC5200 boards evaluate the SVR to print processor name and | |
| version in checkcpu() (cpu/mpc5xxx/cpu.c). | |
| * Patch by Kai-Uwe Bloem, 06 May 2004: | |
| Fix endianess problem in cramfs code | |
| * Patch by Tom Armistead, 04 Jun 2004: | |
| Add support for MAX6900 RTC | |
| * Patches by Ladislav Michl, 03 Jun 2004: | |
| - fix cfi_flash.c on LE systems | |
| - let 'make mrproper' delete u-boot.img as well | |
| - turn printf into debug in cfi_flash.c | |
| * Patch by Kurt Stremerch, 28 May 2004: | |
| Add support for Exys XSEngine board | |
| * Patch by Martin Krause, 27 May 2004: | |
| Fix a MPC5xxx I2C timing issue in i2c_probe(). | |
| * Patch by Leif Lindholm, 27 May 2004: | |
| Fix board_init_f() for dbau1x00 board. | |
| * Patch by Imre Deak, 26 May 2004: | |
| On OMAP1610 platforms check if booting from RAM(CS0) or flash(CS3). | |
| Set flash base accordingly, and decide whether to do or skip board | |
| specific setup steps. | |
| * Patch by Josef Baumgartner, 26 May 2004: | |
| Add missing define in include/asm-m68k/global_data.h | |
| * Patch by Josef Baumgartner, 25 May 2004: | |
| Add missing functions get_ticks() and get_tbclk() in lib_m68k/time.c | |
| * Patch by Paul Ruhland, 24 May 2004: | |
| fix SDRAM initialization for LPD7A400 board. | |
| * Patch by Jian Zhang, 20 May 2004: | |
| add support for environment in NAND flash | |
| * Patch by Yuli Barcohen, 20 May 2004: | |
| Add support for Interphase iSPAN boards. | |
| * Patches by Paul Ruhland, 17 May 2004: | |
| - Add I/O functions to the smc91111 ethernet driver to support the | |
| Logic LPD7A40x boards. | |
| - Add support for the Logic Zoom LH7A40x based SDK board(s), | |
| specifically the LPD7A400. | |
| * Patches by Robert Schwebel, 15 May 2004: | |
| - call MAC address reading code also for SMSC91C111; | |
| - make SMSC91C111 timeout configurable, remove duplicate code | |
| - fix get_timer() for PXA | |
| - update doc/README.JFFS2 | |
| - use "bootfile" env variable also for jffs2 | |
| * Patch by Tolunay Orkun, 14 May 2004: | |
| Add support for Cogent CSB472 board (8MB Flash Rev) | |
| * Patch by Thomas Viehweger, 14 May 2004: | |
| - flash.h: more flash types added | |
| - immap_8260.h: some bits added (useful for RMII) | |
| - cmd_coninfo.c: typo corrected, printf -> puts | |
| - reduced size by replacing spaces with tab | |
| * Patch by Robert Schwebel, 13 May 2004: | |
| Add 'imgextract' command: extract one part of a multi file image. | |
| * Patches by Jon Loeliger, 11 May 2004: | |
| Dynamically handle REV1 and REV2 MPC85xx parts. | |
| (Jon Loeliger, 10-May-2004). | |
| New consistent memory map and Local Access Window across MPC85xx line. | |
| New CCSRBAR at 0xE000_0000 now. | |
| Add RAPID I/O memory map. | |
| New memory map in README.MPC85xxads | |
| (Kumar Gala, 10-May-2004) | |
| Better board and CPU identification on MPC85xx boards at boot. | |
| (Jon Loeliger, 10-May-2004) | |
| SDRAM clock control fixes on MPC8540ADS & MPC8560 boards. | |
| Some configuration options for MPC8540ADS & MPC8560ADS cleaned up. | |
| (Jim Robertson, 10-May-2004) | |
| Rewrite of the MPC85xx Three Speed Ethernet Controller (TSEC) driver. | |
| Supports multiple PHYs. | |
| (Andy Fleming, 10-May-2004) | |
| Some README.MPC85xxads updates. | |
| (Kumar Gala, 10-May-2004) | |
| Copyright updates for "Freescale" | |
| (Andy Fleming, 10-May-2004) | |
| * Patch by Stephen Williams, 11 May 2004: | |
| Add flash support for ST M29W040B | |
| Reduce JSE specific flash.c to remove dead code. | |
| * Patch by Markus Pietrek, 04 May 2004: | |
| Fix clear_bss code for ARM systems (all except s3c44b0 which | |
| doesn't clear BSS at all?) | |
| * Fix "ping" problem on INC-IP board. Strange problem: | |
| Sometimes the store word instruction hangs while writing to one of | |
| the Switch registers, but only if the next instruction is 16-byte | |
| aligned. Moving the instruction into a separate function somehow | |
| makes the problem go away. | |
| * Patch by Rishi Bhattacharya, 08 May 2004: | |
| Add support for TI OMAP5912 OSK Board | |
| * Patch by Sam Song May, 07 May 2004: | |
| Fix typo of UPM table for rmu board | |
| * Patch by Pantelis Antoniou, 05 May 2004: | |
| - Intracom board update. | |
| - Add Codec POST. | |
| * Add support for the second Ethernet interface for the 'PPChameleon' | |
| board. | |
| * Patch by Dave Peverley, 30 Apr 2004: | |
| Add support for OMAP730 Perseus2 Development board | |
| * Patch by Alan J. Luse, 29 Apr 2004: | |
| Fix flash chip-select (OR0) option register setting on FADS boards. | |
| * Patch by Alan J. Luse, 29 Apr 2004: | |
| Report MII network speed and duplex setting properly when | |
| auto-negotiate is not enabled. | |
| * Patch by Jarrett Redd, 29 Apr 2004: | |
| Fix hang on reset on Ocotea board due to flash in wrong mode. | |
| * Patch by Dave Peverley, 29 Apr 2004: | |
| add MAC address detection to smc91111 driver | |
| * Patch by David Müller, 28 Apr 2004: | |
| fix typo in lib_arm/board.c | |
| * Patch by Tolunay Orkun, 20 Apr 2004: | |
| - README update: add CONFIG_CSB272 and csb272_config | |
| - add descriptions for some MII/PHY options, CONFIG_I2CFAST, and | |
| i2cfast environment variable | |
| * Patch by Yuli Barcohen, 19 Apr 2004: | |
| - Rename DUET_ADS to MPC885ADS | |
| - Rename CONFIG_DUET to CONFIG_MPC885_FAMILY | |
| - Rename CONFIG_866_et_al to CONFIG_MPC866_FAMILY | |
| - Clean up FADS family port to use the new defines | |
| * Fix PCI support on CPC45 board | |
| * Patch by Scott McNutt, 25 Apr 2004: | |
| Add Nios GDB/JTAG Console support: | |
| - Add stubs to support gdb via JTAG. | |
| - Add support for console over JTAG. | |
| - Minor cleanup. | |
| * Add support for CATcenter board (based on PPChameleon ME module) | |
| * Patch by Klaus Heydeck, 12 May 2004: | |
| Using external watchdog for KUP4 boards in mpc8xx/cpu.c; | |
| load_sernum_ethaddr() for KUP4 boards in lib_ppc/board.c; | |
| various changes to KUP4 board specific files | |
| * Fix minor network problem on MPC5200: need some delay between | |
| resetting the PHY and sending the first packet. Implemented in a | |
| "natural" way by invoking the PHY reset and initialization code | |
| only once after power on vs. each time the interface is brought up. | |
| * Add some limited support for low-speed devices to SL811 USB controller | |
| (at least "usb reset" now passes successfully and "usb info" displays | |
| correct information) | |
| * Change init sequence for multiple network interfaces: initialize | |
| on-chip interfaces before external cards. | |
| * Fix memory leak in the NAND-specific JFFS2 code | |
| * Fix SL811 USB controller when attached to a USB hub | |
| * Fix config option spelling in PM520 config file | |
| * Fix PHY discovery problem in cpu/mpc8xx/fec.c (introduced by | |
| patches by Pantelis Antoniou, 30 Mar 2004) | |
| * Fix minor NAND JFFS2 related issue | |
| * Fixes for SL811 USB controller: | |
| - implement workaround for broken memory stick | |
| - improve error handling | |
| * Increase packet send timeout to 1 ms in cpu/mpc8xx/scc.c to better | |
| cope with congested networks. | |
| ====================================================================== | |
| Changes for U-Boot 1.1.1: | |
| ====================================================================== | |
| * Patch by Travis Sawyer, 23 Apr 2004: | |
| Fix VSC/CIS 8201 phy descrambler interoperability timing due to | |
| errata from Vitesse Semiconductor. | |
| * Patch by Philippe Robin, 22 Apr 2004: | |
| Fix ethernet configuration for "versatile" board | |
| * Patch by Kshitij Gupta, 21 Apr 2004: | |
| Remove busy loop and use MPU timer fr usleep() on OMAP1510/1610 boards | |
| * Patch by Steven Scholz, 24 Feb 2004: | |
| Fix a bug in AT91RM9200 ethernet driver: | |
| The MII interface is now initialized before accessing the PHY. | |
| * Patch by John Kerl, 19 Apr 2004: | |
| Use U-boot's miiphy.h for PHY register names, rather than | |
| introducing a new header file. | |
| * Update pci_ids.h from linux-2.4.26 | |
| * Patch by Masami Komiya, 19 Apr 2004: | |
| Fix problem cause by VLAN function on little endian architecture | |
| without VLAN environment | |
| * Clean up the TQM8xx_YYMHz configurations; allow to use the same | |
| binary image for all clock frequencies. Implement run-time | |
| optimization of flash access timing based on the actual bus | |
| frequency. | |
| * Modify KUP4X board configuration to use SL811 driver for USB memory | |
| sticks (including FAT / VFAT filesystem support) | |
| * Add SL811 Host Controller Interface driver for USB | |
| * Add CFG_I2C_EEPROM_ADDR_OVERFLOW desription to README | |
| * Patch by Pantelis Antoniou, 19 Apr 2004: | |
| Allow to use shell style syntax (i. e. ${var} ) with standard parser. | |
| Minor patches for Intracom boards. | |
| * Patch by Christian Pell, 19 Apr 2004: | |
| cleanup support for CF/IDE on PCMCIA for PXA25X | |
| * Temporarily disabled John Kerl's extended MII command code because | |
| "miivals.h" is missing | |
| * Patches by Mark Jonas, 13 Apr 2004: | |
| - Remove CS0 chip select timing setting from cpu/mpc5xxx/start.S | |
| - Add sync instructions to IceCube SDRAM init code | |
| - Move SDRAM chip constants into seperate include files | |
| - Unify DDR and SDR initialization code | |
| - Unify all IceCube (Lite5xxx) target names | |
| * Patch by John Kerl, 16 Apr 2004: | |
| Enable ranges in mii command, e.g. mii read 0-1f 0 or | |
| mii read 4-7 18-1a. Also add mii dump subcommand for | |
| pretty-printing standard regs 0-5. | |
| * Patch by Stephen Williams, 16 April 2004: | |
| fix typo in JSE.h; update MAINTAINERS | |
| * Patch by Matthew S. McClintock, 14 Apr 2004: | |
| fix initdram function for utx8245 board | |
| * Patch by Markus Pietrek, 14 Apr 2004: | |
| use ATAG_INITRD2 instead of deprecated ATAG_INITRD tag | |
| * Patch by Reinhard Meyer, 18 Apr 2004: | |
| provide the IDE Reset Function for EMK 5200 boards | |
| * Patch by Masami Komiya, 12 Apr 2004: | |
| fix pci_hose_write_config_{byte,word}_via_dword problems | |
| * Patch by Sangmoon Kim, 12 Apr 2004: | |
| Update max RAM size for debris board | |
| * Patch by Travis Sawyer, 08 Apr 2004: | |
| Add TLB entry for second DIMM slot on ocotea | |
| * Patch by Masami Komiya, 08 Apr 2004: | |
| add RTL8169 network driver | |
| * Patch by Dan Malek, 07 Apr 2004: | |
| - Add support for RPC/STx GP3, Motorola 8560 board | |
| - Update 85xx TSEC driver so it searches MII for first available PHY | |
| and uses that one. | |
| - Add functions to support console MII commands. | |
| * Patch by Tolunay Orkun, 07 Apr 2004: | |
| Move initialization of bi_iic_fast[] | |
| from board_init_f() to board_init_r() | |
| * Patch by Yasushi Shoji, 07 Apr 2004: | |
| Cleanup microblaze port | |
| * Patch by Sangmoon Kim, 07 Apr 2004: | |
| Add auto SDRAM module detection for Debris board | |
| * Patch by Rune Torgersen, 06 Apr 2004: | |
| - Fix some PCI problems on the MPC8266ADS board | |
| - Fix the location of some PCI entries in the immap structure | |
| * Patch by Yasushi Shoji, 07 Apr 2004: | |
| - add support for microblaze processors | |
| - add support for AtmarkTechno "suzaku" board | |
| * Configure PPChameleon board to use redundand environment in flash | |
| * Configure PPChameleon board to use JFFS2 NAND support. | |
| * Added support for JFFS2 filesystem (read-only) on top of NAND flash | |
| * Patch by Rune Torgersen, 16 Apr 2004: | |
| LBA48 fixes | |
| * Patches by Pantelis Antoniou, 16 Apr 2004: | |
| - add support for a new version of an Intracom board and fix | |
| various other things on others. | |
| - add verify support to the crc32 command (define | |
| CONFIG_CRC32_VERIFY to enable it) | |
| - fix FEC driver for MPC8xx systems: | |
| 1. fix compilation problems for boards that use dynamic | |
| allocation of DPRAM | |
| 2. shut down FEC after network transfers | |
| - HUSH parser fixes: | |
| 1. A new test command was added. This is a simplified version of | |
| the one in the bourne shell. | |
| 2. A new exit command was added which terminates the current | |
| executing script. | |
| 3. Fixed handing of $? (exit code of last executed command) | |
| - Fix some compile problems; | |
| add "once" functionality for the netretry variable | |
| * Patch by George G. Davis, 02 Apr 2004: | |
| add support for Intel Assabet board | |
| * Patch by Stephen Williams, 01 Apr 2004: | |
| Add support for Picture Elements JSE board | |
| * Patch by Christian Pell, 01 Apr 2004: | |
| Add CompactFlash support for PXA systems. | |
| * Patches by Pantelis Antoniou, 30 Mar 2004: | |
| - add auto-complete support to the U-Boot CLI | |
| - add support for NETTA and NETPHONE boards; fix NETVIA board | |
| - add support for the Epson 156x series of graphical displays | |
| (These displays are serial and not suitable for using a normal | |
| framebuffer console on them) | |
| - add infrastructure needed in order to POST any DSPs in a board | |
| - improve and fix various things in the MPC8xx FEC driver: | |
| 1. The new 87x and 88x series of processors have two FECs, | |
| and the new driver supports them both. | |
| 2. Another change in the 87x/88x series is support for | |
| the RMII (Reduced MII) interface. However numerous | |
| changes are needed to make it work since the PHYs | |
| are connected to the same lines. That means that | |
| you have to address them correctly over the MII | |
| interface. | |
| 3. We now correctly match the MII/RMII interface | |
| configuration to what the PHY reports. | |
| - Fix problem when readingthe MII status register. Due to the | |
| internal design of many PHYs you have to read the register | |
| twice. The problem is more apparent in 10Mbit mode. | |
| - add new mode ".jffs2s" for reading from a NAND device: it just | |
| skips over bad blocks. | |
| - add networking support for VLANs (802.1q), and CDP (Cisco | |
| Discovery Protocol) | |
| - some minor patches / cleanup | |
| * Patch by Yuli Barcohen, 28 Mar 2004: | |
| - Add support for MPC8272 family including MPC8247/8248/8271/8272 | |
| - Add support for MPC8272ADS evaluation board (another flavour of MPC8260ADS) | |
| - Change configuration method for MPC8260ADS family | |
| * add startup code to clear the BSS of standalone applications | |
| * Fix if / elif handling bug in HUSH shell | |
| ====================================================================== | |
| Changes for U-Boot 1.1.0: | |
| ====================================================================== | |
| * Patch by Mark Jonas: Remove config.tmp files only when | |
| unconfiguring the board | |
| * Adapt RMU board for bigger flash memory | |
| * Patch by Klaus Heydeck, 13 Mar 2003: | |
| Add support for KUP4X Board | |
| * Patch by Pavel Bartusek, 21 Mar 2004 | |
| Add Reiserfs support | |
| * Patch by Hinko Kocevar, 20 Mar 2004 | |
| - Add auto-release for SMSC LAN91c111 driver | |
| - Add save/restore of PTR and PNR regs as suggested in datasheet | |
| * Patch by Stephen Williams, 19 March 2004 | |
| Increase speed of sector reads from SystemACE, | |
| shorten poll timeout and remove a useless reset | |
| * Patch by Tolunay Orkun, 19 Mar 2004: | |
| Make GigE PHY 1000Mbps Speed/Duplex detection conditional | |
| (CONFIG_PHY_GIGE) | |
| * Patch by Brad Kemp, 18 Mar 2004: | |
| prevent machine checks during a PCI scan | |
| * Patch by Pierre Aubert, 18 Mar 2004: | |
| Fix string cleaning in IDE identification | |
| * Patch by Pierre Aubert, 18 Mar 2004: | |
| - Unify video mode handling for Chips & Technologies 69000 Video | |
| chip and Silicon Motion SMI 712/710/810 Video chip | |
| - Add selection of the video output (CRT or LCD) via 'videoout' | |
| environment variable for the Silicon Motion | |
| - README update | |
| * Patch by Pierre Aubert, 18 Mar 2004: | |
| include/common.h typo fix | |
| * Patches by Tolunay Orkun, 17 Mar 2004: | |
| - Add support for bd->bi_iic_fast[] initialization via environment | |
| variable "i2cfast" (CONFIG_I2CFAST) | |
| - Add "i2cfast" u-boot environment variable support for csb272 | |
| * Patch by Carl Riechers, 17 Mar 2004: | |
| Ignore '\0' characters in console input for use with telnet and | |
| telco pads. | |
| * Patch by Leon Kukovec, 17 Mar 2004: | |
| typo fix for strswab prototype #ifdef | |
| * Patches by Thomas Viehweger, 16 Mar 2004: | |
| - show PCI clock frequency on MPC8260 systems | |
| - add FCC_PSMR_RMII flag for HiP7 processors | |
| - in do_jffs2_fsload(), take load address from load_addr if not set | |
| explicit, update load_addr otherwise | |
| - replaced printf by putc/puts when no formatting is needed | |
| (smaller code size, faster execution) | |
| * Patch by Phillippe Robin, 16 Mar 2004: | |
| avoid dereferencing NULL pointer in lib_arm/armlinux.c | |
| * Patch by Stephen Williams, 15 Mar 2004: | |
| Fix CONFIG_SERIAL_SOFTWARE_FIFO documentation | |
| * Patch by Tolunay Orkun, 15 Mar 2004: | |
| Initialize bi_opbfreq to real OPB frequency via get_OPB_freq() | |
| * Patch by Travis Sawyer, 15 Mar 2004: | |
| Update CREDITS & MAINTAINERS files for PPC440GX & Ocotea port | |
| * Add start-up delay to make sure power has stabilized before | |
| attempting to switch on USB on SX1 board. | |
| * Patch by Josef Wagner, 18 Mar 2004: | |
| - Add support for MicroSys XM250 board (PXA255) | |
| - Add support for MicroSys PM828 board (MPC8280) | |
| - Add support for 32 MB Flash on PM825/826 | |
| - new SDRAM refresh rate for PM825/PM826 | |
| - added support for MicroSys PM520 (MPC5200) | |
| - replaced Query by Identify command in CPU86/flash.c | |
| to support 28F160F3B | |
| * Fix wrap around problem with udelay() on ARM920T | |
| * Add support for Macronix flash on TRAB board | |
| * Patch by Pierre Aubert, 15 Mar 2004: | |
| Fix buffer overflow in IDE identification | |
| * Fix power-off of LCD for out-of-band temperatures on LWMON board | |
| * Remove redundand #define in IceCube.h | |
| * Patch by Steven Scholz, 27 Feb 2004: | |
| - Adding get_ticks() and get_tbclk() for AT91RM9200 | |
| - Many white space fixes in cpu/at91rm9200/interrupts.c | |
| * Patches by Steven Scholz, 20 Feb 2004: | |
| some cleanup in AT91RM9200 related code | |
| * Patches by Travis Sawyer, 12 Mar 2004: | |
| - Fix Gigabit Ethernet support for 440GX | |
| - Add Gigabit Ethernet Support to MII PHY utilities | |
| * Patch by Brad Kemp, 12 Mar 2004: | |
| Fixes for drivers/cfi_flash.c: | |
| - Better support for x8/x16 implementations | |
| - Added failure for AMD chips attempting to use CFG_FLASH_USE_BUFFER_WRITE | |
| - Added defines for AMD command and address constants | |
| * Patch by Leon Kukovec, 12 Mar 2004: | |
| Fix get_dentfromdir() to correctly handle deleted dentries | |
| * Patch by George G. Davis, 11 Mar 2004: | |
| Remove hard coded network settings in TI OMAP1610 H2 | |
| default board config | |
| * Patch by George G. Davis, 11 Mar 2004: | |
| add support for ADS GraphicsClient+ board. | |
| * Patch by Pierre Aubert, 11 Mar 2004: | |
| - add bitmap command and splash screen support in cfb console | |
| - add [optional] origin in the bitmap display command | |
| * Patch by Travis Sawyer, 11 Mar 2004: | |
| Fix ocotea board early init interrupt setup. | |
| * Patch by Thomas Viehweger, 11 Mar 2004: | |
| Remove redundand code; add PCI-specific bits to include/mpc8260.h | |
| * Patch by Stephan Linz, 09 Mar 2004 | |
| - Add support for the SSV ADNP/ESC1 (Nios Softcore) | |
| * Patch by George G. Davis, 9 Mar 2004: | |
| fix recent build failure for SA1100 target | |
| * Patch by Travis Sawyer, 09 Mar 2004: | |
| Support native interrupt mode for the IBM440GX. | |
| Previously it was running in 440GP compatibility mode. | |
| * Patch by Philippe Robin, 09 Mar 2004: | |
| Added ARM Integrator AP, CP and Versatile PB926EJ-S Reference | |
| Platform support. | |
| * Patch by Masami Komiya, 08 Mar 2004: | |
| Don't overwrite server IP address or boot file name | |
| when the boot server does not return values | |
| * Patch by Tolunay Orkun, 5 Mar 2004: | |
| Removed compile time restriction on CFG_I2C_SPEED for DS1338 RTC | |
| * Patch by Tolunay Orkun, 5 Mar 2004: | |
| Fix early board initialization for Cogent CSB272 board | |
| * Patch by Ed Okerson, 3 Mar 2004: | |
| fix CFI flash writes for little endian systems | |
| * Patch by Reinhard Meyer, 01 Mar 2004: | |
| generalize USB and IDE support for MPC5200 with according | |
| changes to IceCube.h and TOP5200.h | |
| add Am29LV256 256 MBit FLASH support for TOP5200 boards | |
| add info about USB and IDE to README | |
| * Patch by Yuli Barcohen, 4 Mar 2004: | |
| Fix problems with GCC 3.3.x which changed handling of global | |
| variables explicitly initialized to zero (now in .bss instead of | |
| .data as before). | |
| * Patch by Leon Kukovec, 02 Mar 2004: | |
| add strswab() to fix IDE LBA capacity, firmware and model numbers | |
| on little endian machines | |
| * Patch by Masami Komiya, 02 Mar 2004: | |
| - Remove get_ticks() from NFS code | |
| - Add verification of RPC transaction ID | |
| * Patch by Pierre Aubert, 02 Mar 2004: | |
| cleanup for IDE and USB drivers for MPC5200 | |
| * Patch by Travis Sawyer, 01 Mar 2004: | |
| Ocotea: | |
| - Add IBM PPC440GX Ref Platform support (Ocotea) | |
| Original code by Paul Reynolds <PaulReynolds@lhsolutions.com> | |
| Adapted to U-Boot and 440GX port | |
| 440gx_enet.c: | |
| - Add gracious handling of all Ethernet Pin Selections for 440GX | |
| - Add RGMII selection for Cicada CIS8201 Gigabit PHY | |
| ppc440.h: | |
| - Add needed bit definitions | |
| - Fix formatting | |
| * Patch by Carl Riechers, 1 Mar 2004: | |
| Add PPC440GX prbdv0 divider to fix memory clock calculation. | |
| * Patch by Stephan Linz, 27 Feb 2004 | |
| - avoid problems for targets without NFS download support | |
| * Patch by Rune Torgersen, 27 Feb 2004: | |
| - Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA) | |
| - Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF) | |
| - Added support for 64bit strtoul (CFG_64BIT_STRTOUL) | |
| * Patch by Masami Komiya, 27 Feb 2004: | |
| Fix rarpboot: add autoload by NFS | |
| * Patch by Dan Eisenhut, 26 Feb 2004: | |
| fix flash_write return value in saveenv | |
| * Patch by Stephan Linz, 11 Dec 2003 | |
| expand config.mk to avoid trigraph warnings on NIOS | |
| * Rename "BMS2003" board into "HMI10" | |
| * SX1 patches: use "serial#" for USB serial #; use redundand environment | |
| storage; auto-set console on USB port (using preboot command) | |
| * Add support for SX1 mobile phone; add support for USB-based console | |
| (enable with "setenv stdout usbtty; setenv stdin usbtty") | |
| * Fix LOWBOOT configuration for MPC5200 with DDR memory | |
| * Fix SDRAM timings for LITE5200 / IceCube board | |
| * Handle Auti-MDIX / connection status for INCA-IP | |
| * Fix USB problems when attempting to read 0 bytes | |
| * Patch by Travis Sawyer, 26 Feb 2004: | |
| Fix broken compile for XPEDITE1K target. | |
| * Patch by Stephan Linz, 26 Feb 2004: | |
| Bug fix for NFS code on NIOS targets | |
| * Patch by Stephen Williams, 26 Feb 2004: | |
| Break up SystemACE reads of large block counts | |
| * Patch by Pierre Aubert, 26 Feb 2004 | |
| add IDE support for MPC5200 | |
| * Patch by Masami Komiya, 26 Feb 2004: | |
| add autoload via NFS | |
| * Patch by Stephen Williams | |
| Use of CONFIG_SERIAL_SOFTWARE_FIFO in board.c consistent with uses | |
| elsewhere in the source. | |
| * Patch by Steven Scholz, 25 Feb 2004: | |
| - Timeouts in FPGA code should be based on CFG_HZ | |
| - Minor cleanup in code for Altera FPGA ACEX1K | |
| * Patch by Steven Scholz, 25 Feb 2004: | |
| Changed "Directory Hierarchy" section in README | |
| * Patch by Masami Komiya, 25 Feb 2004: | |
| Reduce copy count in nfs_read_reply() of NFS code | |
| * Patch by Markus Pietrek, 24 Feb 2004: | |
| NS9750 DevBoard added | |
| * Patch by Pierre Aubert, 24 Feb 2004 | |
| add USB support for MPC5200 | |
| * Patch by Steven Scholz, 24 Feb 2004: | |
| - fix MII commands to use values from last command | |
| * Patch by Torsten Demke, 24 Feb 2004: | |
| Add support for the eXalion platform (SPSW-8240, F-30, F-300) | |
| * Patch by Rahul Shanbhag, 19 Feb 2004: | |
| Fixes for for OMAP1610 board: | |
| - shift some IRQ specific code to platform.S file | |
| - remove duplicatewatchdog reset code from start.S | |
| * Make Auto-MDIX Support configurable on INCA-IP board | |
| * Fix license for mkimage tool | |
| * Patch by Masami Komiya, 24 Feb 2004: | |
| Update NetBootFileXferSize in NFS code | |
| * Patch by Scott McNutt, 24 Feb 2004: | |
| fix packet length in NFS code | |
| * Patch by Masami Komiy, 22 Feb 2004: | |
| Add support for NFS for file download | |
| * Patch by Andrea Scian, 17 Feb 2004: | |
| Add support for S3C44B0 processor and DAVE B2 board | |
| * Patch by Steven Scholz, 20 Feb 2004: | |
| - Add support for MII commands on AT91RM9200 boards | |
| - some cleanup in AT91RM9200 ethernet code | |
| * Patch by Peter Ryser, 20 Feb 2004: | |
| Add support for the Xilinx ML300 platform | |
| * Patch by Stephan Linz, 17 Feb 2004: | |
| Fix watchdog support for NIOS | |
| * Patch by Josh Fryman, 16 Feb 2004: | |
| Fix byte-swapping for cfi_flash.c for different bus widths | |
| * Patch by Jon Diekema, 14 Jeb 2004: | |
| Remove duplicate "FPGA Support" notes from the README file | |
| * Patches by Reinhard Meyer, 14 Feb 2004: | |
| - update board/emk tree; use common flash driver | |
| - Corrected tested bits in machine check exception in cpu/mpc5xxx/traps.c | |
| [adapted for other PPC CPUs -- wd] | |
| - Added support for the M48T08 on the EVAL5200 board in rtc/mk48t59.c | |
| * Patch by Jon Diekema, 13 Feb 2004: | |
| Call show_boot_progress() whenever POST "FAILED" is printed. | |
| * Patch by Nishant Kamat, 13 Feb 2004: | |
| Add support for TI OMAP1610 H2 Board | |
| Fixes for cpu/arm926ejs/interrupt.c | |
| (based on Richard Woodruff's patch for arm925, 16 Oct 03) | |
| Fix for a timer bug in OMAP1610 Innovator | |
| Add support for CS0 (ROM)/CS3 (Flash) boot in OMAP1610 Innovator and H2 | |
| * Patches by Stephan Linz, 12 Feb 2004: | |
| - add support for NIOS timer with variable period preload counter value | |
| - prepare POST framework support for NIOS targets | |
| * Patch by Denis Peter, 11 Feb 2004: | |
| add POST support for the MIP405 board | |
| * Patch by Laurent Mohin, 10 Feb 2004: | |
| Fix buffer overflow in common/usb.c | |
| * Patch by Tolunay Orkun, 10 Feb 2004: | |
| Add support for Cogent CSB272 board | |
| * Patch by Thomas Elste, 10 Feb 2004: | |
| Add support for NET+50 CPU and ModNET50 board | |
| * Patch by Sam Song, 10 Feb 2004: | |
| Fix typos in cfi_flash.c | |
| * Patch by Leon Kukovec, 10 Feb 2004 | |
| Fixed long dir entry slot id calculation in get_vfatname | |
| * Patch by Robin Gilks, 10 Feb 2004: | |
| add "itest" command (operators: -eq, -ne, -lt, -gt, -le, -ge, ==, | |
| !=, <>, <, >, <=, >=) | |
| * Fix problem with side effects in macros in include/usb.h | |
| * Patch by David Benson, 13 Nov 2003: | |
| bug 841358 - fix TFTP download size limit | |
| * Fixing bug 850768: | |
| improper flush_cache() in load_serial() | |
| * Fixing bug 834943: | |
| MPC8540 - missing volatile declarations | |
| * Patch by Stephen Williams, 09 Feb 2004: | |
| Add support for Xilinx SystemACE chip: | |
| - New files common/cmd_ace.c and include/systemace.h | |
| - Hook systemace support into cmd_fat and the partition manager | |
| * Patch by Travis Sawyer, 09 Feb 2004: | |
| Add bi_opbfreq & bi_iic_fast to 440GX bd_info as needed for Linux | |
| * Patch by Travis Sawyer, 09 Feb 2004: | |
| o 440GX: | |
| - Fix PCI Indirect access for type 1 config cycles with ppc440. | |
| - Add phymode for 440 enet | |
| - fix pci pre init | |
| o XPedite1K: | |
| - Change board_pre_init to board_early_init_f | |
| - Add user flash to bus controller setup | |
| - Fix pci pre init | |
| - Fix is_pci_host to check GPIO for monarch bit | |
| - Force xpedite1k to pci conventional mode (via #define option) | |
| * Patch by Brad Kemp, 4 Feb 2004: | |
| - handle the machine check that is generated during the PCI scans | |
| on 82xx processors. | |
| - define the registers used in the IMMR by the PCI subsystem. | |
| * Patch by Pierre Aubert, 03 Feb 2004: | |
| cpu/mpc5xxx/start.S: copy MBAR into SPR311 | |
| * Patch by Jeff Angielski, 03 Feb 2004: | |
| Fix copy & paste error in cpu/mpc8260/pci.c | |
| * Patch by Reinhard Meyer, 24 Jan 2004: | |
| Fix typo in cpu/mpc5xxx/pci_mpc5200.c | |
| * Add Auto-MDIX support for INCA-IP | |
| * Some code cleanup | |
| * Patch by Josef Baumgartner, 10 Feb 2004: | |
| Fixes for Coldfire port | |
| * Patch by Brad Kemp, 11 Feb 2004: | |
| Fix CFI flash driver problems | |
| * Make sure to use a bus clock divider of 2 only when running TQM8xxM | |
| modules at CPU clock frequencies above 66 MHz. | |
| * Optimize flash programming speed for LWMON (by another 100% :-) | |
| * Patch by Jian Zhang, 3 Feb 2004: | |
| - Changed the incorrect FAT12BUFSIZE | |
| - data_begin in fsdata can be negative. Changed it to be short. | |
| * Patches by Stephan Linz, 30 Jan 2004: | |
| 1: - board/altera/common/flash.c:flash_erase(): | |
| o allow interrupts befor get_timer() call | |
| o check-up each erased sector and avoid unexpected timeouts | |
| - board/altera/dk1c20/dk1s10.c:board_early_init_f(): | |
| o enclose sevenseg_set() in cpp condition | |
| - remove the ASMI configuration for DK1S10_standard_32 (never present) | |
| - fix some typed in mistakes in the NIOS documentation | |
| 2: - split DK1C20 configuration into several header files: | |
| o two new files for each NIOS CPU description | |
| o U-Boot related part is remaining in DK1C20.h | |
| 3: - split DK1S10 configuration into several header files: | |
| o two new files for each NIOS CPU description | |
| o U-Boot related part is remaining in DK1S10.h | |
| 4: - Add support for the Microtronix Linux Development Kit | |
| NIOS CPU configuration at the Altera Nios Development Kit, | |
| Stratix Edition (DK-1S10) | |
| 5: - Add documentation for the Altera Nios Development Kit, | |
| Stratix Edition (DK-1S10) | |
| 6: - Add support for the Nios Serial Peripharel Interface (SPI) | |
| (master only) | |
| 7: - Add support for the common U-Boot SPI framework at | |
| RTC driver DS1306 | |
| * Patch by Rahul Shanbhag, 28 Jan 2004: | |
| Fix flash protection/locking handling for OMAP1610 innovator board. | |
| * Patch by Rolf Peukert, 28 Jan 2004: | |
| fix flash write problems on CSB226 board (write with 32 bit bus width) | |
| * Patches by Mark Jonas, 16 Jan 2004: | |
| - fix rounding error when calculating baudrates for MPC5200 PSCs | |
| - make sure CFG_RAMBOOT and CFG_LOWBOOT are not enabled at the same | |
| time which is not supported | |
| * Patch by Yuli Barcohen, 26 Jan 2004: | |
| Allow bzip2 compression for small memory footprint boards | |
| * Patch by Brad Kemp, 21 Jan 2004: | |
| Add support for CFI flash driver for both the Intel and the AMD | |
| command sets. | |
| * Patch by Travis Sawyer, 20 Jan 2004: | |
| Fix pci bridge auto enumeration of sibling p2p bridges. | |
| * Patch by Tolunay Orkun, 12 Jan 2004: | |
| Add some delays as needed for Intel LXT971A PHY support | |
| * Patches by Stephan Linz, 09 Jan 2004: | |
| - avoid warning: unused variable `piop' in board/altera/common/sevenseg.c | |
| - make DK1C20 board configuration related to ASMI conform to | |
| documentation | |
| * Patch by Anders Larsen, 09 Jan 2004: | |
| ARM memory layout fixes: the abort-stack is now set up in the | |
| correct RAM area, and the BSS is zeroed out as it should be. | |
| Furthermore, the magic variables 'armboot_end' and 'armboot_end_data' | |
| of the linker scripts are replaced by '__bss_start' and '_end', | |
| resp., which is a further step to eliminate unnecessary differences | |
| between the implementation of the CPU architectures. | |
| * Patch by liang a lei, 9 Jan 2004: | |
| Fix Intel 28F128J3 ID in include/flash.h | |
| * Patch by Masami Komiya, 09 Jan 2004: | |
| add support for TB0229 board (NEC VR4131 MIPS processor) | |
| * Patch by Leon Kukovec, 12 Dec 2003: | |
| changed extern __inline__ into static __inline__ in | |
| include/linux/byteorder/swab.h | |
| * Patch by Travis Sawyer, 30 Dec 2003: | |
| Add support for IBM PPC440GX. Multiple EMAC Ethernet devices, | |
| select MDI port based on enabled EMAC device. | |
| Add support for XES Inc <http://www.xes-inc.com> XPedite1000 440GX | |
| base PrPMC board. | |
| * Patch by Wolter Kamphuis, 15 Dec 2003: | |
| made CONFIG_SILENT_CONSOLE usable on all architectures | |
| * Disable date command on TQM866M - there is no RTC on MPC866 | |
| * Fix variable CPU clock for MPC859/866 systems for low CPU clocks | |
| * Implement adaptive SDRAM timing configuration based on actual CPU | |
| clock frequency for INCA-IP; fix problem with board hanging when | |
| switching from 150MHz to 100MHz | |
| * Add PCMCIA CS support for BMS2003 board | |
| * Add variable CPU clock for MPC859/866 systems (so far only TQM866M): | |
| see doc/README.MPC866 for details; | |
| implement workaround for "SIU4" and "SIU9" silicon bugs on MPC866; | |
| calculate CPU clock frequency from PLL register values. | |
| * Add support for 128 MB RAM on TQM8xxL/M modules | |
| * Fix PS/2 keyboard problem caused by statically initialized variable | |
| pointing to a location in flash | |
| * Fix INCA-IP clock calculation: 400/3 = 133.3 MHz, not 130. | |
| * The PS/2 mux on the BMS2003 board needs 450 ms after power on | |
| before we can access it; add delay in case we are faster (with no | |
| CF card inserted) | |
| * Cleanup of some init functions | |
| * Make sure SCC Ethernet is always stopped by the time we boot Linux | |
| to avoid Linux crashes by early packets coming in. | |
| * Accelerate flash accesses on LWMON board by using buffered writes | |
| * Fix typo in Makefile; | |
| fix problem with PARTNUM detection | |
| * Patch by Reinhard Meyer, 09 Jan 2004: | |
| - add RTC support for MPC5200 based boards (requires RTC_XTAL) | |
| * Add support for IDE LED on BMS2003 board | |
| (exclusive with status LED!) | |
| * Add support for PS/2 keyboard (used with PS/2 multiplexor on | |
| BMS2003 board) | |
| * Patches by Reinhard Meyer, 4 Jan 2004 + 7 Jan 2004: | |
| Add common files for "emk" boards | |
| * Add a common get_ram_size() function and modify the the | |
| board-specific files to invoke that common implementation. | |
| ====================================================================== | |
| Changes for U-Boot 1.0.1: | |
| ====================================================================== | |
| * Set default clock for INCA-IP to 150 MHz | |
| * Make BMS2003 use a separate config file to avoid #ifdef mess; | |
| add I2C support; add support for DS1337 RTC | |
| * Add CompactFlash support for BMS2003 board | |
| * Add support for status LED on BMS2003 board | |
| * Patch by Scott McNutt, 02 Jan 2004: | |
| Add support for the Nios Active Serial Memory Interface (ASMI) | |
| on Cyclone devices | |
| * Patch by Andrea Marson, 16 Dec 2003: | |
| Add support for the PPChameleon ME and HI modules | |
| * Patch by Yuli Barcohen, 22 Dec 2003: | |
| Add support for Motorola DUET ADS board (MPC87x/88x) | |
| * Patch by Robert Schwebel, 15 Dec 2003: | |
| add support for cramfs (uses JFFS2 command interface) | |
| * Patches by Stephan Linz, 11 Dec 2003: | |
| - more documentation for NIOS port | |
| - new struct nios_pio_t, struct nios_spi_t | |
| - Reconfiguration for NIOS Development Kit DK1C20: | |
| o move board related code from board/dk1c20 | |
| to board/altera/dk1c20 | |
| o create a new common source path board/altera/common | |
| and move generic flash access stuff into it | |
| o change/expand configuration file DK1C20.h | |
| - Add support for NIOS Development Kit DK1S10 | |
| - Add status LED support for NIOS systems | |
| - Add dual 7-segment LED support for Altera NIOS DevKits | |
| * Patch by Ronen Shitrit, 10 Dec 2003: | |
| Add support for the Marvell DB64360 / DB64460 development boards | |
| * Patch by Detlev Zundel, 10 Dec 2003: | |
| fix dependency problem in examples/Makefile | |
| * Patch by Denis Peter, 8 Dec 2003 | |
| - add support for the PATI board (MPC555) | |
| - add SPI support for the MPC5xx | |
| * Patch by Anders Larsen, 08 Dec 2003: | |
| add configuration options CONFIG_SERIAL_TAG and CONFIG_REVISION_TAG | |
| to pass ATAG_SERIAL and ATAG_REVISION, resp., to the ARM target; | |
| cleanup some redundand #defines | |
| * Patch by André Schwarz, 8 Dec 2003: | |
| fixes for Davicom DM9102A Ethernet Chip (#define CONFIG_TULIP_FIX_DAVICOM): | |
| - TX and RX deskriptors must be quad-word aligned | |
| - does not work with only one TX deskriptor | |
| - standard reset method does not work | |
| * Patch by Masami Komiya, 08 Dec 2003: | |
| add RTL8139 ethernet driver | |
| * Patches by Ed Okerson, 07 Dec 2003: | |
| - fix ethernet for the AU1x00 processors in little-endian mode. | |
| - extend memsetup.S for the AU1x00 processors in BE and LE modes | |
| * Minor code cleanup (coding style) | |
| * Patch by Reinhard Meyer, 30 Dec 2003: | |
| - cpu/mpc5xxx/fec.c: added CONFIG_PHY_ADDR, added CONFIG_PHY_TYPE, | |
| - added CONFIG_PHY_ADDR to include/configs/IceCube.h, | |
| - turned debug print of PHY registers into a function (called in two places) | |
| - added support for EMK MPC5200 based modules | |
| * Fix MPC8xx PLPRCR_MFD_SHIFT typo | |
| * Add support for TQM866M modules | |
| * Fixes for TQM855M with 4 MB flash (Am29DL163 = _no_ mirror bit flash) | |
| * Fix a few compiler warnings | |
| * Patch by Reinhard Meyer, 28 Dec 2003: | |
| Add initial support for TOP5200 board | |
| * Make CPU clock on ICA-IP board controllable by a "cpuclk" | |
| environment variable which can set to "100", "133", or "150". The | |
| CPU clock will be configured accordingly upon next reboot. Other | |
| values are ignored. In case of an invalid or undefined "cpuclk" | |
| value, the compile-time default CPU clock speed will be used. | |
| * Enable Quad-UART on BMS2003 board (initialize the PCMCIA memory | |
| window that is used to access the UART registers by the Linux driver) | |
| * Patch by Reinhard Meyer, 20 Dec 2003: | |
| Fix clock calculation for the MPC5200 for higher clock frequencies | |
| (above 2**32 / 10 = 429.5 MHz). | |
| * Fix CONFIG_PLL_PCI_TO_MEM_MULTIPLIER divider error in SP8240 configuration | |
| * Fix IceCube CLKIN configuration (it's 33.000000MHz) | |
| * Add new configuration for IceCube board with DDR memory | |
| * Update TRAB memory configurations | |
| * Add JFFS2 support for INCA-IP board | |
| * Patch by Bill Hargen, 09 Dec 2003: | |
| - BUBINGA405EP: changed flash driver to protect top sector containing | |
| first instruction. | |
| - BUBINGA405EP: configured "eeprom" command to access boot config EEPROM. | |
| - BUBINGA405EP: fixed PLL init (init chip selects before FPGA/NVRAM access). | |
| - 405EP: fixed SPD-based SDRAM init (only use banks 0 and 1). | |
| - 405EP: added/fixed support for "reginfo" command. | |
| - 4xx: removed spurious MII error messages on "mii info" command. | |
| * Patch by Bernhard Kuhn, 28 Nov 2003: | |
| add support for Coldfire CPU | |
| add support for Motorola M5272C3 and M5282EVB boards | |
| * Patch by Pierre Aubert, 24 Nov 2003: | |
| - add a return value for the fpga command | |
| - add ide_preinit() function called in ide_init if CONFIG_IDE_PREINIT | |
| is defined. If ide_preinit fails, ide_init is aborted. | |
| - fix an endianess problem in fat.h | |
| * Patch by Wolter Kamphuis, 05 Dec 2003: | |
| Add support for SNMC's QS850/QS823/QS860T boards | |
| * Patch by Yuli Barcohen, 3 Dec 2003: | |
| "revive" U-Boot support for old Motorola MPC860ADS board | |
| * Patch by Cam(ilo?), 03 Dec 2003: | |
| make examples build even with broken Montavista objcopy | |
| * Patch by Pavel Bartusek, 27 Nov 2003: | |
| fix conversion problem with "bootretry" evironment variable | |
| * Patch by Andre Schwarz, 24 Nov 2003: | |
| add support for mvblue (mvBlueLYNX and mvBlueBOX) boards | |
| * Patch by Pavel Bartusek, 21 Nov 2003: | |
| set ZMII bridge speed on 440 | |
| * Patch by Anders Larsen, 17 Nov 2003: | |
| Fix mismatched #ifdef / #endif in include/asm-arm/arch-pxa/hardware.h | |
| * Patches by David Müller, 14 Nov 2003: | |
| - board/mpl/common/common_util.c | |
| * implement support for BZIP2 compressed images | |
| * various cleanups (printf -> puts, ...) | |
| - board/mpl/common/flash.c | |
| * report correct errors to upper layers | |
| * check the erase fail and VPP low bits in status reg | |
| - board/mpl/vcma9/cmd_vcma9.c | |
| - board/mpl/vcma9/flash.c | |
| * various cleanups (printf -> puts, ...) | |
| - common/cmd_usb.c | |
| * fix typo in comment | |
| - cpu/arm920t/usb_ohci.c | |
| * support for S3C2410 is missing in #if line | |
| - drivers/cs8900.c | |
| * reinit some registers in case of error (cable missing, ...) | |
| - fs/fat/fat.c | |
| * support for USB/MMC devices is missing in #if line | |
| - include/configs/MIP405.h | |
| - include/configs/PIP405.h | |
| * enable BZIP2 support | |
| * enlarge malloc space to 1MiB because of BZIP2 support | |
| - include/configs/VCMA9.h | |
| * enable BZIP2 support | |
| * enlarge malloc space to 1MiB because of BZIP2 support | |
| * enable USB support | |
| - lib_arm/armlinux.c | |
| * change calling convention of ARM Linux kernel as | |
| described on http://www.arm.linux.org.uk/developer/booting.php | |
| * Patch by Thomas Lange, 14 Nov 2003: | |
| Split dbau1x00 into dbau1000, dbau1100 and dbau1500 configs to | |
| support all these AMD boards. | |
| * Patch by Thomas Lange, 14 Nov 2003: | |
| Workaround for mips au1x00 physical memory accesses (the au1x00 | |
| uses a 36 bit bus internally and cannot access physical memory | |
| directly. Use the uncached SDRAM address instead of the physical | |
| one.) | |
| * Patch by Xue Ligong (Joe), 13 Nov 2003: | |
| add Realtek 8019 ethernet driver | |
| * Patch by Yuli Barcohen, 13 Nov 2003: | |
| MPC826xADS/PQ2FADS cleanup | |
| * Patch by Anders Larsen, 12 Nov 2003: | |
| Update README to mark the PORTIO commands non-standard | |
| * Patch by Nicolas Lacressonnière, 12 Nov 2003: | |
| update for for Atmel AT91RM9200DK development kit: | |
| - support for environment variables in DataFlash | |
| - Atmel DataFlash AT45DB1282 support | |
| * Patch by Jeff Carr, 11 Nov 2003: | |
| add support for new version of 8270 processors | |
| * Patches by George G. Davis, 05 Nov 2003: | |
| - only pass the ARM linux initrd tag to the kernel when an initrd | |
| is actually present | |
| - update omap1510inn configuration file | |
| * Patches by Stephan Linz, 3 Nov 2003: | |
| - more endianess fixes for LAN91C111 driver | |
| - CFG_HZ configuration patch for NIOS Cyclone board | |
| * Patch by Stephan Linz, 28 Oct 2003: | |
| fix PHY_INT_REG vs. PHY_MASK_REG bug in drivers/smc91111.c | |
| * Patch by Steven Scholz, 20 Oct 2003: | |
| - make "mii info <addr>" show infor for PHY at "addr" only | |
| - Endian fix for miiphy_info() | |
| * Patch by Gleb Natapov, 19 Sep 2003: | |
| Move most of the timer interrupt related PPC code to ppc_lib/interrupts.c | |
| * Patch by Anders Larsen, 17 Sep 2003: | |
| Bring ARM memory layout in sync with the documentation: | |
| stack and malloc-heap are now located _below_ the U-Boot code | |
| * Accelerate booting on TRAB board: read and check autoupdate image | |
| headers first instead of always reading the whole images. | |
| * Fix type in MPC5XXX code (pointed out by Victor Wren) | |
| * Enabled password check on RMU board | |
| * Fix configuration problem with IceCube in LOWBOOT configuration: | |
| envrionment got embedded, corrupting the image layout. | |
| * Fix NEC display names (it's 6440 [for 640x480], not 6640). | |
| * Added BMS2003 board | |
| add support for NEC NL6448BC33-54. 10.4", 640x480 TFT display | |
| * Fix flash driver for TRAB board (must use Unlock Bypass Reset | |
| command to exit Unlock Bypass Mode); adjust timings for flash, SRAM | |
| and CPLD | |
| * Use "-fPIC" instead of "-mrelocatable" to prevent problems with | |
| recent tools | |
| * Add checksum verification to 'imls' command | |
| * Add bd_info fields needed for 4xx Linux I2C driver | |
| * Patch by Martin Krause, 4 Nov. 2003: | |
| Fix error in cmd_vfd.c (TRAB board: "vfd /1" shows now only one Bitmap) | |
| * Print used network interface when CONFIG_NET_MULTI is set | |
| * Patch by Bernhard Kuhn, 28 Oct 2003: | |
| Add low boot support for MPC5200 | |
| * Fix problem with dual PCMCIA support (NSCU) | |
| * Fix MPC5200 I2C initialization function | |
| ====================================================================== | |
| Changes for U-Boot 1.0.0: | |
| ====================================================================== | |
| * Fix parameter passing to standalone images with bootm command | |
| * Patch by Kyle Harris, 30 Oct 2003: | |
| Fix build errors for ixdp425 board | |
| * Patch by David M. Horn, 29 Oct 2003: | |
| Fixes to build under CYGWIN | |
| * Get IceCube MGT5100 working (again) | |
| * Fix problems in memory test on some boards (which was not | |
| non-destructive as intended) | |
| * Patch by Gary Jennejohn, 28 Oct 2003: | |
| Change fs/fat/fat.c to put I/O buffers in BSS instead on the stack | |
| to prevent stack overflow on ARM systems | |
| * Patch by Stephan Linz, 28 Oct 2003: | |
| fix init sequence error for NIOS port | |
| * Allow lowercase spelling for IceCube_5200; support MPC5200LITE name | |
| * Add CONFIG_VERSION_VARIABLE to TRAB configuration | |
| * Patch by Xiao Xianghua, 23 Oct 2003: | |
| small patch for mpc85xx | |
| * Fix small problem in MPC5200 I2C driver | |
| * Fix FCC3 support on ATC board | |
| * Correct header printing for multi-image files in do_bootm() | |
| * Make CONFIG_SILENT_CONSOLE work with CONFIG_AUTOBOOT_KEYED | |
| * Fix PCI problems on PPChameleon board | |
| * Patch by Steven Scholz, 18 Oct 2003: | |
| Fix AT91RM9200 ethernet driver | |
| * Patch by Nye Liu, 17 Oct 2003: | |
| Fix typo in include/mpc8xx.h | |
| * Patch by Richard Woodruff, 16 Oct 03: | |
| Fixes for cpu/arm925/interrupt.c | |
| - Initialize timestamp & lastdec vars. | |
| - fix timestamp overflows. | |
| - fix lastdec overflow. | |
| - smarter normalization to allow udelay() below 1ms to work. | |
| * Patch by Scott McNutt, 16 Oct | |
| add networking support for the Altera Nios Development Kit, | |
| Cyclone Edition (DK-1C20) | |
| * Patch by Jon Diekema, 14 Oct 2003: | |
| add hint about doc/README.silent to README file | |
| * Add CompactFlash support for NSCU | |
| * Fix PCI problems on PPChameleonEVB | |
| * TRAB auto-update: Base decision if we have to strip the image | |
| header on image type as encoded in the header | |
| (include image type patch by Martin Krause, 17 Oct 2003) | |
| * Patches by Xianghua Xiao, 15 Oct 2003: | |
| - Added Motorola CPU 8540/8560 support (cpu/85xx) | |
| - Added Motorola MPC8540ADS board support (board/mpc8540ads) | |
| - Added Motorola MPC8560ADS board support (board/mpc8560ads) | |
| * Fix flash timings on TRAB board | |
| * Make sure HUSH is initialized for running auto-update scripts | |
| * Make 5200 reset command _really_ reset the board, without running | |
| any other code after it | |
| * Fix errors with flash erase when range spans across banks | |
| that are mapped in reverse order | |
| * Fix flash mapping and display on P3G4 board | |
| * Patch by Kyle Harris, 15 Jul 2003: | |
| - add support for Intel IXP425 CPU | |
| - add support for IXDP425 eval board | |
| * Added config option CONFIG_SILENT_CONSOLE. See doc/README.silent | |
| for more information | |
| * Patch by Steven Scholz, 10 Oct 2003 | |
| - Add support for Altera FPGA ACEX1K | |
| * Patches by Thomas Lange, 09 Oct 2003: | |
| - fix cmd_ide.c for non ppc boards (read/write functions did not | |
| add ATA base address) | |
| - fix for shannon board | |
| - #ifdef CONFIG_IDE_8xx_DIRECT some otherwise unused code | |
| - Endian swap ATA identity for all big endian CPUs, not just PPC | |
| - MIPS only: New option CONFIG_MEMSIZE_IN_BYTES for passing memsize | |
| args to linux | |
| - add support for dbau1x00 board (MIPS32) | |
| * Patch by Sangmoon Kim, 07 Oct 2003: | |
| add support for debris board | |
| * Patch by Martin Krause, 09 Oct 2003: | |
| Fixes for TRAB board | |
| - /board/trab/rs485.c: correct baudrate | |
| - /board/trab/cmd_trab.c: bug fix for problem with timer overflow in | |
| udelay(); fix some timing problems with adc controller | |
| - /board/trab/trab_fkt.c: add new commands: gain, eeprom and power; | |
| modify commands: touch and buzzer | |
| * Disable CONFIG_SUPPORT_VFAT when used with CONFIG_AUTO_UPDATE | |
| (quick & dirty workaround for rogue pointer problem in get_vfatname()); | |
| Use direct function calls for auto_update instead of hush commands | |
| * Patch by Scott McNutt, 04 Oct 2003: | |
| - add support for Altera Nios-32 CPU | |
| - add support for Nios Cyclone Development Kit (DK-1C20) | |
| * Patch by Steven Scholz, 29 Sep 2003: | |
| - A second parameter for bootm overwrites the load address for | |
| "Standalone Application" images. | |
| - bootm sets environment variable "filesize" to the resulting | |
| (uncompressed) data length for "Standalone Application" images | |
| when autostart is set to "no". Now you can do something like | |
| if bootm $fpgadata $some_free_ram ; then | |
| fpga load 0 $some_free_ram $filesize | |
| fi | |
| * Patch by Denis Peter, 25 Sept 2003: | |
| add support for the MIP405 Rev. C board | |
| * Patch by Yuli Barcohen, 25 Sep 2003: | |
| add support for Zephyr Engineering ZPC.1900 board | |
| * Patch by Anders Larsen, 23 Sep 2003: | |
| add CMD_PORTIO to CFG_CMD_NONSTD (commands in question are only | |
| implemented for the x86 architecture) | |
| * Patch by Sangmoon Kim, 23 Sep 2003: | |
| fix pll_pci_to_mem_multiplier table for MPC8245 | |
| * Patch by Anders Larsen, 22 Sep 2003: | |
| enable timed autoboot on PXA | |
| * Patch by David Müller, 22 Sep 2003: | |
| - add $(CFLAGS) to "-print-libgcc-filename" so compiler driver | |
| returns correct libgcc file path | |
| - "latency" reduction of busy-loop waiting to improve "U-Boot" boot | |
| time on s3c24x0 systems | |
| * Patch by Jon Diekema, 19 Sep 2003: | |
| - Add CFG_FAULT_ECHO_LINK_DOWN option to echo the inverted Ethernet | |
| link state to the fault LED. | |
| - In NetLoop, make the Fault LED reflect the link status. The link | |
| status gets updated on entry, and on timeouts. | |
| * Patch by Anders Larsen, 18 Sep 2003: | |
| allow mkimage to build and run on Cygwin-hosted systems | |
| * Patch by Frank Müller, 18 Sep 2003: | |
| use bi_intfreq instead of bi_busfreq to compute fec_mii_speed in | |
| cpu/mpc8xx/fec.c | |
| * Patch by Pantelis Antoniou, 16 Sep 2003: | |
| add tool to compute fileds in the PLPRCR register for MPC86x | |
| * Use IH_TYPE_FILESYSTEM for TRAB "disk" images. | |
| * Fix build problems under FreeBSD | |
| * Add generic filesystem image type | |
| * Make fatload set filesize environment variable | |
| * enable basic / medium / high-end configurations for PPChameleonEVB | |
| board; fix NAND code | |
| * enable TFTP client code to specify to the server the desired | |
| timeout value (see RFC-2349) | |
| * Improve SDRAM setup for TRAB board | |
| * Suppress all output with splashscreen configured only if "splashimage" | |
| is set | |
| * Fix problems with I2C support for mpc5200 | |
| * Adapt TRAB configuration and auto_update to new memory layout | |
| * Add configuration for wtk board | |
| * Add support for the Sharp LQ065T9DR51U LCD display | |
| * Patch by Rune Torgersen, 17 Sep 2003: | |
| - Fixes for MPC8266 default config | |
| - Allow eth_loopback_test() on 8260 to use a subset of the FCC's | |
| * Patches by Jon Diekema, 17 Sep 2003: | |
| - update README (SHOW_BOOT_PROGRESS values for cmd_nand.c and | |
| env_common.c) | |
| - sbc8260 tweaks | |
| - adjust "help" output | |
| * Patches by Anders Larsen, 17 Sep 2003: | |
| - fix spelling errors | |
| - set GD_FLG_DEVINIT flag only after device function pointers | |
| are valid | |
| - Allow CFG_ALT_MEMTEST on systems where address zero isn't | |
| writeable | |
| - enable 3.rd UART (ST-UART) on PXA(XScale) CPUs | |
| - trigger watchdog while waiting in serial driver | |
| * Add auto-update code for TRAB board using USB memory sticks, | |
| support new configuration with more memory | |
| * disable MPC5200 bus pipelining as workaround for bus contention | |
| * Modify XLB arbiter priorities on MPC5200 so all devices use same | |
| priority; configure critical interrupts to be handled like external | |
| interrupts | |
| * Make IPB clock on MGT5100/MPC5200 configurable in board config file; | |
| go back to 66 MHz for stability | |
| * Patches by Jon Diekema, 15 Sep 2003: | |
| - add description for missing CFG_CMD_* entries in the README file | |
| - sacsng tweaks | |
| * Patch by Gleb Natapov, 14 Sep 2003: | |
| enable watchdog support for all MPC824x boards that have a watchdog | |
| * On MPC5200, restrict FEC to a maximum of 10 Mbps to work around the | |
| "Non-octet Aligned Frame" errors we see at 100 Mbps | |
| * Patch by Sharad Gupta, 14 Sep 2003: | |
| fix SPR numbers for upper BAT register ([ID]BAT[4-7][UL]) | |
| * Patch by llandre, 11 Sep 2003: | |
| update configuration for PPChameleonEVB board | |
| * Patch by David Müller, 13 Sep 2003: | |
| various changes to VCMA9 board specific files | |
| * Add I2C support for MGT5100 / MPC5200 | |
| * Patch by Rune Torgersen, 11 Sep 2003: | |
| Changed default memory option on MPC8266ADS to NOT be Page Based | |
| Interleave, since this doesn't work very well with the standard | |
| 16MB DIMM | |
| * Patch by George G. Davis, 12 Sep 2003: | |
| fix Makefile settings for sk98 driver | |
| * Patch by Stefan Roese, 12 Sep 2003: | |
| - new boards added: DP405, HUB405, PLU405, VOH405 | |
| - some esd boards updated | |
| - cpu/ppc4xx/sdram.c: disable memory controller before setting | |
| first values | |
| - cpu/ppc4xx/405_pci.c: set vendor id on PPC405EP systems | |
| * Patch by Martin Krause, 11 Sep 2003: | |
| add burn-in tests for TRAB board | |
| * Enable instruction cache on MPC5200 board | |
| * Patch by Denis Peter, 11 Sep 2003: | |
| - fix USB data pointer assignment for bulk only transfer. | |
| - prevent to display erased directories in FAT filesystem. | |
| * Change output format for NAND flash - make it look like for other | |
| memory, too | |
| ====================================================================== | |
| Changes for U-Boot 0.4.8: | |
| ====================================================================== | |
| * Add I2C and RTC support for RMU board | |
| * Patches by Denis Peter, 9 Sep 2003: | |
| add FAT support for IDE, SCSI and USB | |
| * Patches by Gleb Natapov, 2 Sep 2003: | |
| - cleanup of POST code for unsupported architectures | |
| - MPC824x locks way0 of data cache for use as initial RAM; | |
| this patch unlocks it after relocation to RAM and invalidates | |
| the locked entries. | |
| * Patch by Gleb Natapov, 30 Aug 2003: | |
| new I2C driver for mpc107 bridge. Now works from flash. | |
| * Patch by Dave Ellis, 11 Aug 2003: | |
| - JFFS2: fix typo in common/cmd_jffs2.c | |
| - JFFS2: fix CFG_JFFS2_SORT_FRAGMENTS option | |
| - JFFS2: remove node version 0 warning | |
| - JFFS2: accept JFFS2 PADDING nodes | |
| - SXNI855T: add AM29LV800 support | |
| - SXNI855T: move environment from EEPROM to flash | |
| - SXNI855T: boot from JFFS2 in NOR or NAND flash | |
| * Patch by Bill Hargen, 11 Aug 2003: | |
| fixes for I2C on MPC8240 | |
| - fix i2c_write routine | |
| - fix iprobe command | |
| - eliminates use of global variables, plus dead code, cleanup. | |
| * Add support for USB Mass Storage Devices (BBB) | |
| (tested with USB memory sticks only) | |
| * Avoid flicker on TRAB's VFD | |
| * Add support for SK98xx driver | |
| * Add PCI support for SL8245 board | |
| * Support IceCube board configurations with 1 x AMD AM29LV065 (8 MB) | |
| or 1 x AM29LV652 (two LV065 in one chip = 16 MB); | |
| Run IPB at 133 Mhz; adjust the MII clock frequency accordingly | |
| * Set BRG_CLK on PM825/826 to 64MHz (VCO_OUT / 4, instead of 16 MHz) | |
| to allow for more accurate baudrate settings | |
| (error now 0.7% at 115 kbps, instead of 3.5% before) | |
| * Patch by Andreas Mohr, 4 Sep 2003: | |
| Fix a lot of spelling errors | |
| * Add support for PPChameleon Eval Board | |
| * Add support for P3G4 board | |
| * Fix problem with MGT5100 FEC driver: add "early" MAC address | |
| initialization | |
| * Patch by Yuli Barcohen, 7 Aug 2003: | |
| check BCSR to detect if the board is configured in PCI mode | |
| ====================================================================== | |
| Changes for U-Boot 0.4.7: | |
| ====================================================================== | |
| * Patch by Raghu Krishnaprasad, 7 Aug 2003: | |
| add support for Adder II MPC852T module | |
| * Patch by George G. Davis, 19 Aug 2003: | |
| fix TI Innovator/OMAP1510 pin configs | |
| * Patches by Kshitij, 18 Aug 2003 | |
| - add support for arm926ejs cpu core | |
| - add support for TI OMAP 1610 Innovator Board | |
| * Patch by Yuli Barcohen, 14 Aug 2003: | |
| add support for bzip2 uncompression | |
| * Add GCC library to examples/Makefile so GCC utility functions will | |
| be resolved, too | |
| * Add I2C and RTC support for RMU board using software I2C driver | |
| (because of better response to iprobe command); fix problem with | |
| "reset" command | |
| * Patch by Matthias Fuchs, 28 Aug 2003: | |
| Added CONFIG_BOOTP_DNS2 and CONFIG_BOOTP_SEND_HOSTNAME to | |
| CONFIG_BOOTP_MAKS (see README). | |
| * Fix ICU862 environment problem | |
| * Fix RAM size detection for RMU board | |
| * Implement "reset" for MGT5100/MPC5200 systems | |
| ====================================================================== | |
| Changes for U-Boot 0.4.6: | |
| ====================================================================== | |
| * Make Ethernet autonegotiation on INCA-IP work for all clock rates; | |
| allow selection of clock frequency as "make" target | |
| * Implement memory autosizing code for IceCube boards | |
| * Configure network port on INCA-IP for autonegotiation | |
| * Fix overflow problem in network timeout code | |
| * Patch by Richard Woodruff, 8 Aug 2003: | |
| Allow crc32 to be used at address 0x000 (crc32_no_comp, too). | |
| ====================================================================== | |
| Changes for U-Boot 0.4.5: | |
| ====================================================================== | |
| * Update for TQM board defaults: | |
| disable clocks_in_mhz, enable boot count limit | |
| * Removed tools/gdb from "make all" target. Added make target "gdbtools" | |
| in toplevel directory instead. Removed astest.c from tools/gdb because | |
| it is no longer relevant. | |
| * Fix PCI support for MPC5200 / IceCube Board | |
| * Map ISP1362 USB OTG controller for NSCU board | |
| * Patch by Brad Parker, 02 Aug 2003: | |
| fix sc520_cdp problems | |
| * Implement Boot Cycle Detection (Req. 2.3 of OSDL CGL Reqirements) | |
| * Allow erase command to cross flash bank boundaries | |
| * Patch by Scott McNutt, 21 Jul 2003: | |
| Add support for LynuxWorks Kernel Downloadable Images (KDIs). | |
| Both LynxOS and BlueCat linux KDIs are supported. | |
| * Patch by Richard Woodruff, 25 Jul 2003: | |
| use more reliable reset for OMAP/925T | |
| * Patch by Nye Liu, 25 Jul 2003: | |
| fix typo in mpc8xx.h | |
| * Patch by Richard Woodruff, 24 Jul 2003: | |
| Fixes for cmd_nand.c: | |
| - Fixed null dereferece which could result in incorrect ECC values. | |
| - Added support for devices with no Ready/Busy signal hooked up. | |
| - Added OMAP1510 read/write protect handling. | |
| - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock | |
| for non-JFFS2. | |
| - Switched default ECC to be JFFS2. | |
| * Allow crc32 to be used at address 0x000 | |
| * Provide consistent interface to standalone applications to access | |
| the 'global_data' structure | |
| Provide a doc/README.standalone more useful to users/developers. | |
| * Make IceCube MGT5100 FEC driver work | |
| * Implement new mechanism to export U-Boot's functions to standalone | |
| applications: instead of using (PPC-specific) system calls we now | |
| use a jump table; please see doc/README.standalone for details | |
| * Patch by Dave Westwood, 24 Jul 2003: | |
| added support for Unity OS (a proprietary OS) | |
| * Patch by Detlev Zundel, 23 Jul 2003: | |
| add "imls" command to print flash table of contents | |
| * Fix cold boot detection for log buffer reset | |
| * Return error for invalid length specifiers with "cp.X" etc. | |
| * Fix startup problem on MIPS | |
| * Allow for CONFIG_SPLASH_SCREEN even when no explicit | |
| bitmap support is configured | |
| * Patch by Bill Hargen, 18 Jul 2003: | |
| - fix endinaness problem in cpu/mpc824x/drivers/i2c/i2c1.c | |
| * Patch by Denis Peter, 18 Jul 2003: | |
| - fix memory configuration for MIP405T | |
| - fix printout of baudrate for "loadb <loadaddr> <baudrate>" | |
| * Cleanup of TQM82xx configurations; use "official" board types | |
| to make selection easier. | |
| * Patch by Martin Krause, 17 Jul 2003: | |
| add delay to get I2C working with "imm" command and s3c24x0_i2c.c | |
| * Patch by Richard Woodruff, 17 July 03: | |
| - Fixed bug in OMAP1510 baud rate divisor settings. | |
| * Patch by Nye Liu, 16 July 2003: | |
| MPC860FADS fixes: | |
| - add MPC86xADS support (uses MPC86xADS.h) | |
| - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T) | |
| o PLPRCR changes | |
| o BRG changes (EXTAL/XTAL restricted to 10MHz) | |
| o don't trust gclk() software measurement by default, depend on | |
| CONFIG_8xx_GCLK_FREQ | |
| - add DRAM SIMM not installed detection | |
| - use more "correct" SDRAM initialization sequence | |
| - allow different SDRAM sizes (8xxADS has 8M) | |
| - default DER is 0 | |
| - remove unused MAMR defines from FADS860T.h (all done in fads.c) | |
| - rename MAMR/MBMR defines to be more consistent. Should eventually | |
| be merged into MxMR to better reflect the PowerQUICC datasheet. | |
| * Patch by Yuli Barcohen, 16 Jul 2003: | |
| support new Motorola PQ2FADS-ZU evaluation board which replaced | |
| MPC8260ADS and MPC8266ADS | |
| ====================================================================== | |
| Changes for U-Boot 0.4.4: | |
| ====================================================================== | |
| * Add support for IceCube board (with MGT5100 and MPC5200 CPUs) | |
| * Add support for MGT5100 and MPC5200 processors | |
| * Patch by Lutz Dennig, 15 Jul 2003: | |
| update for R360MPI board | |
| ====================================================================== | |
| Changes for U-Boot 0.4.3: | |
| ====================================================================== | |
| * Patches by Kshitij, 04 Jul 2003 | |
| - added support for arm925t cpu core | |
| - added support for TI OMAP 1510 Innovator Board | |
| * Patches by Martin Krause, 14 Jul 2003: | |
| - add I2C support for s3c2400 systems (trab board) | |
| - (re-) add "ping" to command table | |
| * Fix handling of "slow" POST routines | |
| * Patches by Yuli Barcohen, 13 Jul 2003: | |
| - Correct flash and JFFS2 support for MPC8260ADS | |
| - fix PVR values and clock generation for PowerQUICC II family | |
| (8270/8275/8280) | |
| * Patch by Bernhard Kuhn, 08 Jul 2003: | |
| - add support for M68K targets | |
| * Patch by Ken Chou, 3 Jul: | |
| - Fix PCI config table for A3000 | |
| - Fix iobase for natsemi.c | |
| (PCI_BASE_ADDRESS_0 is the IO base register for DP83815) | |
| * Allow to enable "slow" POST routines by key press on power-on | |
| * Fix temperature dependend switching of LCD backlight on LWMON | |
| * Tweak output format for LWMON | |
| * Patch by Stefan Roese, 11 Jul 2003: | |
| - Fix bug in CONFIG_VERSION_VARIABLE. | |
| - AR405 config updated. | |
| - OCRTC/ORSG: bsp command added. | |
| - ASH405 bsp update. | |
| ====================================================================== | |
| Changes for U-Boot 0.4.2: | |
| ====================================================================== | |
| * Add support for NSCU board | |
| * Add support for TQM823M, TQM850M, TQM855M and TQM860M modules | |
| * Add support for Am29LV160ML, Am29LV320ML, and Am29LV640ML | |
| mirror bit flash on TQM8xxM modules | |
| * Patch by Kenneth Johansson, 30 Jun 2003: | |
| get rid of MK_CMD_ENTRY macro; update doc/README.command | |
| * Patch by Seb James, 30 Jun 2003: | |
| Improve documentation of I2C configuration in README | |
| * Fix problems with previous log buffer "fixes" | |
| * Fix minor help text issues | |
| * "log append" did not append a newline | |
| ====================================================================== | |
| Changes for U-Boot 0.4.1: | |
| ====================================================================== | |
| * Fix some missing commands, cleanup header files | |
| (autoscript, bmp, bsp, fat, mmc, nand, portio, ...) | |
| * Rewrite command lookup and help command (fix problems with bubble | |
| sort when sorting command name list). Minor cleanup here and there. | |
| * Merge from "stable branch", tag LABEL_2003_06_28_1800-stable: | |
| - Allow to call sysmon function interactively | |
| - PIC on LWMON board needs delay after power-on | |
| - Add missing RSR definitions for MPC8xx | |
| - Improve log buffer handling: guarantee clean reset after power-on | |
| - Add support for EXBITGEN board (aka "genie") | |
| - Add support for SL8245 board | |
| * Code cleanup: | |
| - remove trailing white space, trailing empty lines, C++ comments, etc. | |
| - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c) | |
| * Patches by Kenneth Johansson, 25 Jun 2003: | |
| - major rework of command structure | |
| (work done mostly by Michal Cendrowski and Joakim Kristiansen) | |
| ====================================================================== | |
| Changes for U-Boot 0.4.0: | |
| ====================================================================== | |
| * Patches by Robert Schwebel, 26 Jun 2003: | |
| - csb226 configuration updated | |
| - credits for logodl port updated | |
| - innokom configuration updated | |
| - logodl tree update, still with coding style inconsistencies | |
| - added OCM for ppc405 warning to README | |
| * Patch by Pantelis Antoniou, 25 Jun 2003: | |
| update NetVia with V2 board support | |
| * Header file cleanup for ARM | |
| * Patch by Murray Jensen, 24 Jun 2003: | |
| - make sure to use only U-boot provided header files | |
| - fix problems with ".rodata.str1.4" section as used by GCC-3.x | |
| * Patch by Stefan Roese, 24 Jun 2003: | |
| - Update esd ASH405 board files. | |
| - Update esd DASA_SIM config file. | |
| - Add ping command to some esd boards. | |
| * Patch by Yuli Barcohen, 23 Jun 2003: | |
| Update for MPC8260ADS board | |
| * Patch by Murray Jensen, 23 Jun 2003: | |
| - cleanup of GCC 3.x compiler warnings | |
| * Patch by Rune Torgersen, 4 Jun 2003: | |
| add large memory support for MPC8266ADS board | |
| * Patch by Richard Woodruff, 19 June 03: | |
| - Enabled standard u-boot device abstraction for ARM | |
| - Enabled console device for ARM | |
| - Initilized bi_baudrate for ARM | |
| * Patch by Bill Hargen, 23 Apr 2003: | |
| fix byte order for 824x I2C addresses (write op) | |
| * Patch by Murray Jensen, 20 Jun 2003: | |
| - hymod update | |
| - cleanup (especially for gcc-3.x compilers) | |
| * Patch by Tom Guilliams, 20 Jun 2003: | |
| added CONFIG_750FX support for IBM 750FX processors | |
| * Patch by Devin Crumb, 02 Apr 2003: | |
| Fix clock divider rounding problem in drivers/serial.c | |
| * Patch by Richard Woodruff, 19 June 03: | |
| - Fixed smc91c111 driver to sync with the u-boot environment | |
| (driver/smc91c111.c). | |
| - Added eth_init error return check in NetLoop (net/net.c). | |
| * Patch by Ken Chou, 19 June 2003: | |
| Added support for A3000 SBC board (Artis Microsystems Inc.) | |
| * Patches by Murray Jensen, 17 Jun 2003: | |
| - Hymod board database mods: add "who" field and new xilinx chip types | |
| - provide new "init_cmd_timeout()" function so code external to | |
| "common/main.c" can use the "reset_cmd_timeout()" function before | |
| entering the main loop | |
| - add DTT support for adm1021 (new file dtt/adm1021.c; config | |
| slightly different. see include/configs/hymod.h for an example | |
| (requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and | |
| CFG_DTT_ADM1021 defined) | |
| - add new "eeprom_probe()" function which has similar args and | |
| behaves in a similar way to "eeprom_read()" etc. | |
| - add 8260 FCC ethernet loopback code (new "eth_loopback_test()" | |
| function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST) | |
| - gdbtools copyright update | |
| - ensure that set_msr() executes the "sync" and "isync" instructions | |
| after the "mtmsr" instruction in cpu/mpc8260/interrupts.c | |
| - 8260 I/O ports fix: Open Drain should be set last when configuring | |
| - add SIU IRQ defines for 8260 | |
| - allow LDSCRIPT override and OBJCFLAGS initialization: change to | |
| config.mk to allow board configurations to override the GNU | |
| linker script, selected via the LDSCRIPT, make variable, and to | |
| give an initial value to the OBJCFLAGS make variable | |
| - 8260 i2c enhancement: | |
| o correctly extends the timeout depending on the size of all | |
| queued messages for both transmit and receive | |
| o will not continue with receive if transmit times out | |
| o ensures that the error callback is done for all queued tx | |
| and rx messages | |
| o correctly detects both tx and rx timeouts, only delivers one to | |
| the callback, and does not overwrite an earlier error | |
| o logic in i2c_probe now correct | |
| - add "vprintf()" function so that "panic()" function can be | |
| technically correct | |
| - many Hymod board changes | |
| * Patches by Robert Schwebel, 14 Jun 2003: | |
| - add support for Logotronic DL datalogger board | |
| - cleanup serial line after kermit binary download | |
| - add debugX macro (debug level support) | |
| - update mach-types.h to latest arm.linux.org.uk master list. | |
| * Patches by David Müller, 12 Jun 2003: | |
| - rewrite of the S3C24X0 register definitions stuff | |
| - "driver" for the built-in S3C24X0 RTC | |
| * Patches by Yuli Barcohen, 12 Jun 2003: | |
| - Add MII support and Ethernet PHY initialization for MPC8260ADS board | |
| - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset | |
| configuration word supplied by FPGA on some MPC8260ADS boards | |
| * Patch by Pantelis Antoniou, 10 Jun 2003: | |
| Unify status LED interface | |
| * Add support for DS12887 RTC; add RTC support for ATC board | |
| * Patch by Nicolas Lacressonniere, 11 Jun 2003: | |
| Modifications for Atmel AT91RM9200DK ARM920T based development kit | |
| - Add Atmel DataFlash support for reading and writing. | |
| - Add possibility to boot a Linux from DataFlash with BOOTM command. | |
| - Add Flash detection on Atmel AT91RM9200DK | |
| (between Atmel AT49BV1614 and AT49BV1614A flashes) | |
| - Replace old Ethernet PHY layer functions | |
| - Change link address | |
| * Patch by Frank Smith, 9 Jun 2003: | |
| use CRIT_EXCEPTION for machine check on 4xx | |
| * Patch by Detlev Zundel, 13 Jun 2003: | |
| added implementation of the "carinfo" command in cmd_immap.c | |
| * Fix CONFIG_NET_MULTI support in include/net.h | |
| * Patches by Kyle Harris, 13 Mar 2003: | |
| - Add FAT partition support | |
| - Add command support for FAT | |
| - Add command support for MMC | |
| ---- | |
| - Add Intel PXA support for video | |
| - Add Intel PXA support for MMC | |
| ---- | |
| - Enable MMC and FAT for lubbock board | |
| - Other misc changes for lubbock board | |
| * Patch by Robert Schwebel, April 02, 2003: | |
| fix for SMSC91111 driver | |
| * Patch by Vladimir Gurevich, 04 Jun 2003: | |
| make ppc405 ethernet driver compatible with CONFIG_NET_MULTI option | |
| * Patch by Stefan Roese, 05 Jun 2003: | |
| - PPC4xx: Fix bug for initial stack in data cache as pointed out by | |
| Thomas Schaefer (tschaefer@giga-stream.de). Now inital stack in | |
| data cache can be used even if the chip select is in use. | |
| - CFG_RX_ETH_BUFFER added to set the ethernet receive buffer count | |
| (see README for further description). | |
| - Changed config files of CONFIG_EEPRO100 boards to use the | |
| CFG_RX_ETH_BUFFER define. | |
| * Add support for RMU board | |
| * Add support for TQM862L at 100/50 MHz | |
| * Patch by Pantelis Antoniou, 02 Jun 2003: | |
| major reconstruction of networking code; | |
| add "ping" support (outgoing only!) | |
| * Patch by Denis Peter, 04 June 2003: | |
| add support for the MIP405T board | |
| * Patches by Udi Finkelstein, 2 June 2003: | |
| - Added support for custom keyboards, initialized by defining a | |
| board-specific drv_keyboard_init as well as defining CONFIG_KEYBOARD . | |
| - Added support for the RBC823 board. | |
| - cpu/mpc8xx/lcd.c now automatically calculates the | |
| Horizontal Pixel Count field. | |
| * Fix alignment problem in BOOTP (dhcp_leasetime option) | |
| [pointed out by Nicolas Lacressonnière, 2 Jun 2003] | |
| * Patch by Mark Rakes, 14 May 2003: | |
| add support for Intel e1000 gig cards. | |
| * Patch by Nye Liu, 3 Jun 2003: | |
| fix critical typo in MAMR definition (include/mpc8xx.h) | |
| * Fix requirement to align U-Boot image on 16 kB boundaries on PPC. | |
| * Patch by Klaus Heydeck, 2 Jun 2003 | |
| Minor changes for KUP4K configuration | |
| * Patch by Marc Singer, 29 May 2003: | |
| Fixed rarp boot method for IA32 and other little-endian CPUs. | |
| * Patch by Marc Singer, 28 May 2003: | |
| Added port I/O commands. | |
| * Patch by Matthew McClintock, 28 May 2003 | |
| - cpu/mpc824x/start.S: fix relocation code when booting from RAM | |
| - minor patches for utx8245 | |
| * Patch by Daniel Engström, 28 May 2003: | |
| x86 update | |
| * Patch by Dave Ellis, 9 May 2003 + 27 May 2003: | |
| add nand flash support to SXNI855T configuration | |
| fix/extend nand flash support: | |
| - fix 'nand erase' command so does not erase bad blocks | |
| - fix 'nand write' command so does not write to bad blocks | |
| - fix nand_probe() so handles no flash detected properly | |
| - add doc/README.nand | |
| - add .jffs2 and .oob options to nand read/write | |
| - add 'nand bad' command to list bad blocks | |
| - add 'clean' option to 'nand erase' to write JFFS2 clean markers | |
| - make NAND read/write faster | |
| * Patch by Rune Torgersen, 23 May 2003: | |
| Update for MPC8266ADS board | |
| * Get (mostly) rid of CFG_MONITOR_LEN definition; compute real length | |
| instead CFG_MONITOR_LEN is now only used to determine _at_compile_ | |
| _time_ (!) if the environment is embedded within the U-Boot image, | |
| or in a separate flash sector. | |
| * Cleanup CFG_DER #defines in config files (wd maintained only) | |
| * Fix data abort exception handling for arm920t CPU | |
| * Fix alignment problems with flash driver for TRAB board | |
| * Patch by Donald White, 21 May 2003: | |
| fix calculation of base address in pci_hose_config_device() | |
| * Fix bug in command line parsing: "cmd1;cmd2" is supposed to always | |
| execute "cmd2", even if "cmd1" fails. Note that this is different | |
| to "run var1 var2" where the contents of "var2" will NOT be | |
| executed when a command in "var1" fails. | |
| * Add zero-copy ramdisk support (requires corresponding kernel support!) | |
| * Patch by Kyle Harris, 20 May 2003: | |
| In preparation for an ixp port, rename cpu/xscale and arch-xscale | |
| into cpu/pxa and arch-pxa. | |
| * Patch by Stefan Roese, 23 May 2003: | |
| - IBM PPC405EP port added. | |
| - CONFIG_UART1_CONSOLE added. If defined internal UART1 (and not | |
| UART0) is used as default U-Boot console. PPC4xx only! | |
| - esd ASH405 board added (PPC405EP based). | |
| - BUBINGA405EP board added (PPC405EP based - IBM Eval Board). | |
| - esd CPCI405AB board added. | |
| - esd PMC405 board added. | |
| - Update of some esd boards. | |
| * Patch by Denis Peter, 19 Mai 2003: | |
| add support for the MIP405-3 board | |
| * Patch by Dave Ellis, 22 May 2003: | |
| Fix problem with only partially cleared .bss segment | |
| * Patch by Rune Torgersen, 12 May 2003: | |
| get PCI to work on a MPC8266ADS board; incorporate change to | |
| cpu/mpc8260/pci.c to enable overrides of PCI memory parameters | |
| * Patch by Nye Liu, 1 May 2003: | |
| minor patches for the FADS8xx | |
| * Patch by Thomas Schäfer, 28 Apr 2003: | |
| Fix SPD handling for 256 ECC DIMM on Walnut | |
| * Add support for arbitrary bitmaps for TRAB's VFD command; | |
| allow to pass boot bitmap addresses in environment variables; | |
| allow for zero boot delay | |
| * Patch by Christian Geißinger, 19 May 2002: | |
| On TRAB: wait until the dummy byte has been completely sent | |
| * Patch by David Updegraff, 22 Apr 2003: | |
| update for CrayL1 board | |
| * Patch by Pantelis Antoniou, 21 Apr 2003: | |
| add boot support for ARTOS (a proprietary OS) | |
| * Patch by Steven Scholz, 11 Apr 2003: | |
| Add support for RTC DS1338 | |
| * Patch by Rod Boyce, 24 Jan 2003: | |
| Fix counting of extended partitions in diskboot command | |
| * Patch by Christophe Lindheimer, 20 May 2003: | |
| allow the use of CFG_LOADS when CFG_NO_FLASH is set | |
| * Fix SDRAM timing on Purple board | |
| * Add support for CompactFlash on ATC board | |
| (includes support for Intel 82365 and compatible PC Card controllers, | |
| and Yenta-compatible PCI-to-CardBus controllers) | |
| * Patch by Mathijs Haarman, 08 May 2003: | |
| Add lan91c96 driver (tested on Lubbock and custom PXA250 board only) | |
| * Fix problem with usage of "true" (undefined in current versions of bfd.h) | |
| * Add support for Promess ATC board | |
| * Patch by Keith Outwater, 28 Apr 2003: | |
| - Miscellaneous corrections and additions to GEN860T board specific code. | |
| - Added GEN860_SC variant to GEN860T. | |
| - Miscellaneous corrections to GEN860T documentation. | |
| - Correct duplicate entry in U-Boot CREDITS file. | |
| - Add GEN860T_SC entry in MAINTAINERS file. | |
| - Update CREDITS file with GEN860T_SC info. | |
| * Update Smiths Aerospace addresses in MAINTAINERS file | |
| * Fix error handling in hush's version of "run" command | |
| * LWMON extensions: | |
| - Splashscreen support | |
| - modem support | |
| - sysmon support | |
| - temperature dependend enabling of LCD | |
| * Allow booting from old "PPCBoot" disk partitions | |
| * Add support for TQM8255 Board / MPC8255 CPU | |
| ====================================================================== | |
| Changes for U-Boot 0.3.1: | |
| ====================================================================== | |
| * Make sure Block Lock Bits get cleared in R360MPI flash driver | |
| * MPC823 LCD driver: Fill color map backwards, to allow for steady | |
| display when Linux takes over | |
| * Patch by Erwin Rol, 27 Feb 2003: | |
| Add support for RTEMS (this time for real). | |
| * Add support for "bmp info" and "bmp display" commands to load | |
| bitmap images; this can be used (for example in a "preboot" | |
| command) to display a splash screen very quickly after poweron. | |
| * Add support for 133 MHz clock on INCA-IP board | |
| * Patch by Lutz Dennig, 10 Apr 2003: | |
| Update for R360MPI board | |
| * Add new meaning to "autostart" environment variable: | |
| If set to "no", a standalone image passed to the | |
| "bootm" command will be copied to the load address | |
| (and eventually uncompressed), but NOT be started. | |
| This can be used to load and uncompress arbitrary | |
| data. | |
| * Patch by Stefan Roese, 10 Apr 2003: | |
| Changed DHCP client to use IP address from server option field #54 | |
| from the OFFER packet in the server option field #54 in the REQUEST | |
| packet. This fixes a problem using a Windows 2000 DHCP server, | |
| where the DHCP-server is not the TFTP-server. | |
| * Set max brightness for MN11236 displays on TRAB board | |
| * Add support for TQM862L modules | |
| ====================================================================== | |
| Changes for U-Boot 0.3.0: | |
| ====================================================================== | |
| * Patch by Arun Dharankar, 4 Apr 2003: | |
| Add IDMA example code (tested on 8260 only) | |
| * Add support for Purple Board (MIPS64 5Kc) | |
| * Add support for MIPS64 5Kc CPUs | |
| * Fix missing setting of "loadaddr" and "bootfile" on ARM and MIPS | |
| * Patch by Denis Peter, 04 Apr 2003: | |
| - update MIP405-4 board | |
| * Patch by Stefan Roese, 4 Apr 2003: | |
| - U-Boot version environment variable "ver" added | |
| (CONFIG_VERSION_VARIABLE). | |
| - Changed PPC405GPr version from A to B. | |
| - Changed CPCI405 to use CTS instead of DSR on PPC405 UART1. | |
| * Patches by Denis Peter, 03 April 2003: | |
| - fix PCI IRQs on MPL boards | |
| - fix two more un-relocated pointer problems | |
| * Fix behaviour of "run" command: | |
| - print error message iv variable does not exist | |
| - terminate processing of arguments in case of error | |
| * Patches by Peter Figuli, 10 Mar 2003 | |
| - Add support for BTUART on PXA platform | |
| - Add support for WEP EP250 (PXA) board | |
| * Fix flash problems on INCA-IP; add tool to allow bruning images to | |
| flash using a BDI2000 | |
| * Implement fix for I2C Edge Conditions problem for all boards that | |
| use the bit-banging driver (common/soft_i2c.c) | |
| * Patch by Martin Winistoerfer, 23 Mar 2003 | |
| - Add port to MPC555/556 microcontrollers | |
| - Add support for cmi customer board with | |
| Intel 28F128J3A, 28F320J3A or 28F640J3A flash. | |
| * Patch by Rick Bronson, 28 Mar 2003: | |
| - fix common/cmd_nand.c | |
| * Patch by Arun Dharankar, 24 Mar 2003: | |
| - add threads / scheduler example code | |
| * Add patches by Robert Schwebel, 31 Mar 2003: | |
| - add ctrl-c support for kermit download | |
| - align bdinfo output on ARM | |
| - csb226 board: bring in sync with innokom/memsetup.S | |
| - csb226 board: fix MDREFR handling | |
| - misc doc fixes / extensions | |
| - innokom board: cleanup, MDREFR fix in memsetup.S, config update | |
| - add BOOT_PROGRESS to armlinux.c | |
| * Add CPU ID, version, and clock speed for INCA-IP | |
| * Patches by Dave Ellis, 18 Mar 2003 for SXNI855T board: | |
| - fix SRAM and SDRAM memory sizing | |
| - add status LED support | |
| - add MAC address for second (SCC1) ethernet port | |
| * Update default environment for TQM8260 board | |
| * Patch by Rick Bronson, 16 Mar 2003: | |
| - Add NAND flash support for reading, writing, and erasing NAND | |
| flash (certain forms of which are called SmartMedia). | |
| - Add support for Atmel AT91RM9200DK ARM920T based development kit. | |
| * Patches by Robert Schwebel, 19 Mar 2003: | |
| - use arm-linux-gcc as default compiler for ARM | |
| - fix i2c fixup code | |
| - fix missing baudrate setting | |
| - added $loadaddr / CFG_LOAD_ADDR support to loadb | |
| - moved "ignoring trailing characters" _before_ u-boot wants to | |
| print out diagnostics messages; removes bogus characters at the | |
| end of transmission | |
| * Patch by John Zhan, 18 Mar 2003: | |
| Add support for SinoVee Microsystems SC8xx boards | |
| * Patch by Rolf Offermanns, 21 Mar 2003: | |
| ported the dnp1110 related changes from the current armboot cvs to | |
| current u-boot cvs. smc91111 does not work. problem marked in | |
| smc91111.c, grep for "FIXME". | |
| * Patch by Brian Auld, 25 Mar 2003: | |
| Add support for STM flash chips on ebony board | |
| * Add PCI support for MPC8250 Boards (PM825 module) | |
| * Patch by Stefan Roese, 25 Mar 2003: | |
| - PCI405 update. | |
| * Patch by Stefan Roese, 20 Mar 2003: | |
| - CPCI4052 update (support for revision 3). | |
| - Set edge conditioning circuitry on PPC405GPr for compatibility | |
| to existing PPC405GP designs. | |
| - Clip udiv to 5 bits on PPC405 (serial.c). | |
| * Extend INCAIP board support: | |
| - add automatic RAM size detection | |
| - add "bdinfo" command | |
| - pass flash address and size to Linux kernel | |
| - switch to 150 MHz clock | |
| * Avoid flicker on the TRAB's VFD by synchronizing the enable with | |
| the HSYNC/VSYNC. Requires new CPLD code (Version 101 for Rev. 100 | |
| boards, version 153 for Rev. 200 boards). | |
| * Patch by Vladimir Gurevich, 12 Mar 2003: | |
| Fix relocation problem of statically initialized string pointers | |
| in common/cmd_pci.c | |
| * Patch by Kai-Uwe Blöm, 12 Mar 2003: | |
| Cleanup & bug fixes for JFFS2 code: | |
| - the memory mangement was broken. It caused havoc on malloc by | |
| writing beyond the block boundaries. | |
| - the length calculation for files was wrong, sometimes resulting | |
| in short file reads. | |
| - data copying now optionally takes fragment version numbers into | |
| account, to avoid copying from older data. | |
| See doc/README.JFFS2 for details. | |
| * Patch by Josef Wagner, 12 Mar 2003: | |
| - 16/32 MB and 50/80 MHz support with auto-detection for IP860 | |
| - ETH05 and BEDBUG support for CU824 | |
| - added support for MicroSys CPC45 | |
| - new BOOTROM/FLASH0 and DOC base for PM826 | |
| * Patch by Robert Schwebel, 12 Mar 2003: | |
| Fix the chpart command on innokom board | |
| * Name cleanup: | |
| mv include/asm-i386/ppcboot-i386.h include/asm-i386/u-boot-i386.h | |
| s/PPCBoot/U-Boot/ in some files | |
| s/pImage/uImage/ in some files | |
| * Patch by Detlev Zundel, 15 Jan 2003: | |
| Fix '' command line quoting | |
| * Patch by The LEOX team, 19 Jan 2003: | |
| - add support for the ELPT860 board | |
| - add support for Dallas ds164x RTC | |
| * Patches by David Müller, 31 Jan 2003: | |
| - minimal setup for CardBus bridges | |
| - add EEPROM read/write support in the CS8900 driver | |
| - add support for the builtin I2C controller in the Samsung s3c24x0 chips | |
| - add support for MPL's VCMA9 (Samsung s3c2410 based) board | |
| * Patch by Steven Scholz, 04 Feb 2003: | |
| add support for RTC DS1307 | |
| * Patch by Reinhard Meyer, 5 Feb 2003: | |
| fix PLPRCR/SCCR init sequence on 8xx to allow for | |
| changes of EBDF by software | |
| * Patch by Vladimir Gurevich, 07 Feb 2003: | |
| "API-compatibility patch" for 4xx I2C driver | |
| * TRAB fixes / extensions: | |
| - Restore VFD brightness as saved in environment | |
| - add support for Fujitsu flashes | |
| - make sure both buzzers are turned off (drive low level) | |
| * Patches by Robert Schwebel, 06 Mar 2003: | |
| - fix bug in BOOTP code (must use NetCopyIP) | |
| - update of CSB226 port | |
| - clear BSS segment on XScale | |
| - added support for i2c_init_board() function | |
| - update to the Innokom plattform | |
| * Extend support for redundand environments for configurations where | |
| environment size < sector size | |
| * Patch by Rune Torgersen, 13 Feb 2003: | |
| Add support for Motorola MPC8266ADS board | |
| * Patch by Kyle Harris, 19 Feb 2003: | |
| patches for the Intel lubbock board: | |
| memsetup.S - general cleanup (based on Robert's csb226 code) | |
| flash.c - overhaul, actually works now | |
| lubbock.c - fix init funcs to return proper value | |
| * Patch by Kenneth Johansson, 26 Feb 2003: | |
| - Fixed off by one in RFTA calculation. | |
| - No need to abort when LDF is lower than we can program it's only | |
| minimum timing so clamp it to what we can do. | |
| - Takes function pointer to function for reading the spd_nvram. Usefull | |
| for faking data or hardcode a module without the nvram. | |
| - fix other user for above change | |
| - fix some comments. | |
| * Patches by Brian Waite, 26 Feb 2003: | |
| - fix port for evb64260 board | |
| - fix PCI for evb64260 board | |
| - fix PCI scan | |
| * Patch by Reinhard Meyer, 1 Mar 2003: | |
| Add support for EMK TOP860 Module | |
| * Patch by Yuli Barcohen, 02 Mar 2003: | |
| Add SPD EEPROM support for MPC8260ADS board | |
| * Patch by Robert Schwebel, 21 Jan 2003: | |
| - Add support for Innokom board | |
| - Don't complain if "install" fails | |
| - README cleanup (remove duplicated lines) | |
| - Update PXA header files | |
| * Add documentation for existing POST code (doc/README.POST) | |
| * Patch by Laudney Ren, 15 Jan 2003: | |
| Fix handling of redundand environment in "tools/envcrc.c" | |
| * Patch by Detlev Zundel, 28 Feb 2003: | |
| Add bedbug support for 824x systems | |
| * Add support for 16 MB flash configuration of TRAB board | |
| * Patch by Erwin Rol, 27 Feb 2003: | |
| Add support for RTEMS | |
| * Add image information to README | |
| * Patch by Stefan Roese, 18 Feb 2003: | |
| CPCIISER4 configuration updated. | |
| * Patch by Stefan Roese, 17 Feb 2003: | |
| Fixed bug in ext. serial clock setup on PPC405 (since PPC440 port). | |
| * Patch by Stefan Roese, 13 Feb 2003: | |
| Add "pcidelay" environment variable (in ms, enabled via | |
| CONFIG_PCI_BOOTDELAY). | |
| PCI spec 2.2 defines, that a pci target has 2^25 pci clocks after | |
| RST# to respond to configuration cycles (33MHz -> 1s). | |
| * Fix dual PCMCIA slot support (when running with just one | |
| slot populated) | |
| * Add VFD type detection to trab board | |
| * extend drivers/cs8900.c driver to synchronize ethaddr environment | |
| variable with value in the EEPROM | |
| * Patch by Stefan Roese, 10 Feb 2003: | |
| Add support for 4MB and 128MB onboard SDRAM (cpu/ppc4xx/sdram.c) | |
| * Add support for MIPS32 4Kc CPUs | |
| * Add support for INCA-IP Board | |
| ====================================================================== | |
| Changes for U-Boot 0.2.2: | |
| ====================================================================== | |
| * Add dual ethernet support on PM826 | |
| * Add support for LXT971 PHY on PM826 | |
| * Patch by Tord Andersson, 16 Jan 2003: | |
| Fix flash sector count for TQM8xxL | |
| * Fix I2C EEPROM problem on ICU862 board (would only write the first | |
| 16 bytes out of each 32 byte block) | |
| ====================================================================== | |
| Changes for U-Boot 0.2.1: | |
| ====================================================================== | |
| * Add support for V37 board | |
| (patch by Jón Benediktsson, 11 Dec 2002) | |
| * Update baudrate in bd_info when it gets changed | |
| * Add watchdog trigger points while waiting for serial port | |
| (so far only 8xx -- needed on LWMON with 100ms watchdog) | |
| * Improve command line tool to access the U-Boot's environment | |
| (figuration of the utility, using a config file) | |
| * Add single quote support for (old) command line parser | |
| * Switch LWMON board default config from FRAM to EEPROM; | |
| in POST, EEPROM shows up on 8 addresses | |
| ====================================================================== | |
| Changes for U-Boot 0.2.0: | |
| ====================================================================== | |
| * Use 1-byte-read instead of -write for iprobe() function | |
| Add i2c commands to PM826 config | |
| * extend I2C POST code: check for list on known addresses | |
| * Improve log buffer code; use "loglevel" to decide which messages | |
| to log on the console, too (like in Linux); get rid of "logstart" | |
| * Add command line tool to access the U-Boot's environment | |
| (board-specific for TRAB now, to be fixed later) | |
| * Patch by Hans-Joerg Frieden, 06 Dec 2002 | |
| Fix misc problems with AmigaOne support | |
| * Patch by Chris Hallinan, 3 Dec 2002: | |
| minor cleanup to the MPC8245 EPIC driver | |
| * Patch by Pierre Aubert , 28 Nov 2002 | |
| Add support for external (SIU) interrupts on MPC8xx | |
| * Patch by Pierre Aubert , 28 Nov 2002 | |
| Fix nested syscalls bug in standalone applications | |
| * Patch by David Müller, 27 Nov 2002: | |
| fix output of "pciinfo" command for CardBus bridge devices. | |
| * Fix bug in TQM8260 board detection - boards got stuck when board ID | |
| was not readable | |
| * Add LED indication for IDE activity on KUP4K board | |
| * Fix startup problems with VFD display on TRAB | |
| * Patch by Pierre Aubert, 20 Nov 2002 | |
| Add driver for Epson SED13806 graphic controller. | |
| Add support for BMP logos in cfb_console driver. | |
| * Added support for both PCMCIA slots (at the same time!) on MPC8xx | |
| * Patch by Rod Boyce, 21 Nov 2002: | |
| fix PCMCIA on MBX8xx board | |
| * Patch by Pierre Aubert , 21 Nov 2002 | |
| Add CFG_CPM_POST_WORD_ADDR to make the offset of the | |
| bootmode word in DPRAM configurable | |
| * Patch by Daniel Engström, 18 Nov 2002: | |
| Fixes for x86 port (mostly strings issues) | |
| * Patch by Ken Chou, 18 Nov 2002: | |
| Fix for natsemi NIC cards (DP83815) | |
| * Patch by Pierre Aubert, 19 Nov 2002: | |
| fix a bug for the MII configuration, and some warnings | |
| * Patch by Thomas Frieden, 13 Nov 2002: | |
| Add code for AmigaOne board | |
| (preliminary merge to U-Boot, still WIP) | |
| * Patch by Jon Diekema, 12 Nov 2002: | |
| - Adding URL for IEEE OUI lookup | |
| - Making the autoboot #defines dependent on CONFIG_AUTOBOOT_KEYED | |
| being defined. | |
| - In the CONFIG_EXTRA_ENV_SETTINGS #define, the root-on-initrd and | |
| root-on-nfs macros are designed to switch how the default boot | |
| method gets defined. | |
| * Patch by Daniel Engström, 13 Nov 2002: | |
| Add support for i386 architecture and AMD SC520 board | |
| * Patch by Pierre Aubert, 12 Nov 2002: | |
| Add support for DOS filesystem and booting from DOS floppy disk | |
| * Patch by Jim Sandoz, 07 Nov 2002: | |
| Increase number of network RX buffers (PKTBUFSRX in | |
| "include/net.h") for EEPRO100 based boards (especially SP8240) | |
| which showed "Receiver is not ready" errors when U-Boot was | |
| processing the receive buffers slower than the network controller | |
| was filling them. | |
| * Patch by Andreas Oberritter, 09 Nov 2002: | |
| Change behaviour of NetLoop(): return -1 for errors, filesize | |
| otherwise; return code 0 is valid an means no file loaded - in this | |
| case the environment still gets updated! | |
| * Patches by Jon Diekema, 9 Nov 2002: | |
| - improve ADC/DAC clocking on the SACSng board to align | |
| the failing edges of LRCLK and SCLK | |
| - sbc8260 configuration tweaks | |
| - add status LED support for 82xx systems | |
| - wire sspi/sspo commands into command handler; improved error | |
| handlering | |
| - add timestamp support and alternate memory test to the | |
| SACSng configuration | |
| * Patch by Vince Husovsky, 7 Nov 2002: | |
| Add "-n" to linker options to get rid of "Not enough room for | |
| program headers" problem | |
| * Patch by David Müller, 05 Nov 2002 | |
| Rename CONFIG_PLL_INPUT_FREQ to CONFIG_SYS_CLK_FREQ | |
| so we can use an already existing name | |
| * Patch by Pierre Aubert, 05 Nov 2002 | |
| Hardware relatied improvments in FDC boot code | |
| * Patch by Holger Schurig, 5 Nov 2002: | |
| Make the PXA really change it's frequency | |
| * Patch by Pierre Aubert, 05 Nov 2002 | |
| Add support for slave serial Spartan 2 FPGAs | |
| * Fix uninitialized memory (MAC address) in 8xx SCC/FEC ethernet | |
| drivers | |
| * Add support for log buffer which can be passed to Linux kernel's | |
| syslog mechanism; used especially for POST results. | |
| * Patch by Klaus Heydeck, 31 Oct 2002: | |
| Add initial support for kup4k board | |
| * Patch by Robert Schwebel, 04 Nov 2002: | |
| - use watchdog to reset PXA250 systems | |
| - added progress callbacks to (some of the) ARM code | |
| - update for Cogent CSB226 board | |
| * Add support for FPS860 board | |
| * Patch by Guillaume Alexandre,, 04 Nov 2002: | |
| Improve PCI access on 32-bits Compact PCI bus | |
| * Fix mdelay() on TRAB - this was still the debugging version with | |
| seconds instead of ms. | |
| * Patch by Robert Schwebel, 1 Nov 2002: | |
| XScale related cleanup (affects all ARM boards) | |
| * Cleanup of names and README. | |
| ====================================================================== | |
| Notes for U-Boot 0.1.0: | |
| ====================================================================== | |
| This is the initial version of "Das U-Boot", the Universal Boot Loader. | |
| It is based on version 2.0.0 (the "Halloween Release") of PPCBoot. | |
| For information about the history of the project please see the | |
| PPCBoot project page at http://sourceforge.net/projects/ppcboot | |
| ====================================================================== |