blob: 32f26672e2ff1ac3213c4bd3faf7165c0662bd7f [file] [log] [blame]
/*
* (C) Copyright 2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <ppc_asm.tmpl>
#include <config.h>
#include <asm/mmu.h>
#include <asm/ppc4xx.h>
/**************************************************************************
* TLB TABLE
*
* This table is used by the cpu boot code to setup the initial tlb
* entries. Rather than make broad assumptions in the cpu source tree,
* this table lets each board set things up however they like.
*
* Pointer to the table is returned in r1
*
*************************************************************************/
.section .bootpg,"ax"
/**************************************************************************
* TLB table for revA
*************************************************************************/
.globl tlbtabA
tlbtabA:
tlbtab_start
/*
* BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
* speed up boot process. It is patched after relocation to enable SA_I
*/
tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_RWX | SA_G)
/*
* TLB entries for SDRAM are not needed on this platform.
* They are dynamically generated in the SPD DDR(2) detection
* routine.
*/
tlbentry(CONFIG_SYS_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_RWX | SA_I)
tlbentry(CONFIG_SYS_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE_BASE, SZ_16K, 0x20000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE0_CFGBASE, SZ_16M, 0x40000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE1_CFGBASE, SZ_16M, 0x80000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE2_CFGBASE, SZ_16M, 0xC0000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE0_XCFGBASE, SZ_1K, 0x50000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE1_XCFGBASE, SZ_1K, 0x90000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE2_XCFGBASE, SZ_1K, 0xD0000000, 0xC, AC_RW | SA_IG)
tlbtab_end
/**************************************************************************
* TLB table for revB
*
* Notice: revB of the 440SPe chip is very strict about PLB real addresses
* and ranges to be mapped for config space: it seems to only work with
* d_nnnn_nnnn range (hangs the core upon config transaction attempts when
* set otherwise) while revA uses c_nnnn_nnnn.
*************************************************************************/
.globl tlbtabB
tlbtabB:
tlbtab_start
/*
* BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
* speed up boot process. It is patched after relocation to enable SA_I
*/
tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_RWX | SA_G)
/*
* TLB entries for SDRAM are not needed on this platform.
* They are dynamically generated in the SPD DDR(2) detection
* routine.
*/
tlbentry(CONFIG_SYS_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_RWX | SA_I)
tlbentry(CONFIG_SYS_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_ACE_BASE, SZ_1K, CONFIG_SYS_ACE_BASE, 4,AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE0_CFGBASE, SZ_16M, 0x00000000, 0xD, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE1_CFGBASE, SZ_16M, 0x20000000, 0xD, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE2_CFGBASE, SZ_16M, 0x40000000, 0xD, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_RW | SA_IG)
tlbentry(CONFIG_SYS_PCIE2_XCFGBASE, SZ_1K, 0x50000000, 0xD, AC_RW | SA_IG)
tlbtab_end