| Freescale Alaska MPC8220 board |
| ============================== |
| |
| TsiChung Liew(Tsi-Chung.Liew@freescale.com) |
| Created 9/21/04 |
| =========================================== |
| |
| |
| Changed files: |
| ============== |
| |
| - Makefile added MPC8220 and Alaska8220_config |
| - MAKEALL added MPC8220 and Alaska8220 |
| - README added CONFIG_MPC8220, Alaska8220_config |
| |
| - common/cmd_bdinfo.c added board information members for MPC8220 |
| - common/cmd_bootm.c added clocks for MPC8220 in do_bootm_linux() |
| |
| - include/common.h added CONFIG_MPC8220 |
| |
| - include/asm-ppc/u-boot.h added board information members for MPC8220 |
| - include/asm-ppc/global_data.h added global variables - inp_clk, pci_clk, |
| vco_clk, pev_clk, flb_clk, and bExtUart |
| |
| - lib_ppc/board.c added CONFIG_MPC8220 support |
| |
| - net/eth.c added FEC support for MPC8220 |
| |
| Added files: |
| ============ |
| - board/alaska directory for Alaska MPC8220 |
| - board/alaska/alaska.c Alaska dram and BATs setup |
| - board/alaska/extserial.c external serial (debug card serial) support |
| - board/alaska/flash.c Socket (AMD) and Onboard (INTEL) flash support |
| - board/alaska/serial.c to determine which int/ext serial to use |
| - board/alaska/Makefile Makefile |
| - board/alaska/config.mk config make |
| - board/alaska/u-boot.lds Linker description |
| |
| - cpu/mpc8220/dma.h multi-channel dma header file |
| - cpu/mpc8220/dramSetup.h dram setup header file |
| - cpu/mpc8220/fec.h MPC8220 FEC header file |
| - cpu/mpc8220/cpu.c cpu specific code |
| - cpu/mpc8220/cpu_init.c Flexbus ChipSelect and Mux pins setup |
| - cpu/mpc8220/dramSetup.c MPC8220 DDR SDRAM setup |
| - cpu/mpc8220/fec.c MPC8220 FEC driver |
| - cpu/mpc8220/i2c.c MPC8220 I2C driver |
| - cpu/mpc8220/interrupts.c interrupt support (not enable) |
| - cpu/mpc8220/loadtask.c load dma |
| - cpu/mpc8220/speed.c system, pci, flexbus, pev, and cpu clock |
| - cpu/mpc8220/traps.c exception |
| - cpu/mpc8220/uart.c MPC8220 UART driver |
| - cpu/mpc8220/Makefile Makefile |
| - cpu/mpc8220/config.mk config make |
| - cpu/mpc8220/fec_dma_task.S MPC8220 FEC multi-channel dma program |
| - cpu/mpc8220/io.S io functions |
| - cpu/mpc8220/start.S start up |
| |
| - include/mpc8220.h |
| |
| - include/asm-ppc/immap_8220.h |
| |
| - include/configs/Alaska8220.h |
| |
| |
| 1. SWITCH SETTINGS |
| ================== |
| 1.1 SW1: 0 - Boot from Socket Flash (AMD) or 1 - Onboard Flash (INTEL) |
| SW2: 0 - Select MPC8220 UART or 1 - Debug Card UART |
| SW3: unsed |
| SW4: 0 - 1284 or 1 - FEC1 |
| SW5: 0 - PEV or 1 - FEC2 |
| |
| |
| 2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL |
| =========================================== |
| 2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and |
| linux kernel, you can customize it based on your system requirements: |
| DDR: 0x00000000-0x1fffffff (max 512MB) |
| MBAR: 0xf0000000-0xf0027fff (128KB) |
| CPLD: 0xf1000000-0xf103ffff (256KB) |
| FPGA: 0xf2000000-0xf203ffff (256KB) |
| Flash: 0xfe000000-0xffffffff (max 32MB) |
| |
| 3. DEFINITIONS AND COMPILATION |
| ============================== |
| 3.1 Explanation on NEW definitions in include/configs/alaska8220.h |
| CONFIG_MPC8220 MPC8220 specific |
| CONFIG_ALASKA8220 Alaska board specific |
| CONFIG_SYS_MPC8220_CLKIN Define Alaska Input Clock |
| CONFIG_PSC_CONSOLE Enable MPC8220 UART |
| CONFIG_EXTUART_CONSOLE Enable External 16552 UART |
| CONFIG_SYS_AMD_BOOT To determine the u-boot is booted from AMD or Intel |
| CONFIG_SYS_MBAR MBAR base address |
| CONFIG_SYS_DEFAULT_MBAR Reset MBAR base address |
| |
| 3.2 Compilation |
| export CROSS_COMPILE=cross-compile-prefix |
| cd u-boot-1-1-x |
| make distclean |
| make Alaska8220_config |
| make |
| |
| |
| 4. SCREEN DUMP |
| ============== |
| 4.1 Alaska MPC8220 board |
| Boot from AMD (NOTE: May not show exactly the same) |
| |
| U-Boot 1.1.1 (Sep 22 2004 - 22:14:41) |
| |
| CPU: MPC8220 (JTAG ID 1640301d) at 300 MHz |
| Bus 120 MHz, CPU 300 MHz, PCI 30 MHz, VCO 480 MHz |
| Board: Alaska MPC8220 Evaluation Board |
| I2C: 93 kHz, ready |
| DRAM: 256 MB |
| Reserving 167k for U-Boot at: 0ffd6000 |
| FLASH: 16.5 MB |
| *** Warning - bad CRC, using default environment |
| |
| In: serial |
| Out: serial |
| Err: serial |
| Net: FEC ETHERNET |
| => flinfo |
| |
| Bank # 1: INTEL 28F128J3A |
| Size: 8 MB in 64 Sectors |
| Sector Start Addresses: |
| FE000000 FE020000 FE040000 FE060000 FE080000 |
| FE0A0000 FE0C0000 FE0E0000 FE100000 FE120000 |
| FE140000 FE160000 FE180000 FE1A0000 FE1C0000 |
| FE1E0000 FE200000 FE220000 FE240000 FE260000 |
| FE280000 FE2A0000 FE2C0000 FE2E0000 FE300000 |
| FE320000 FE340000 FE360000 FE380000 FE3A0000 |
| FE3C0000 FE3E0000 FE400000 FE420000 FE440000 |
| FE460000 FE480000 FE4A0000 FE4C0000 FE4E0000 |
| FE500000 FE520000 FE540000 FE560000 FE580000 |
| FE5A0000 FE5C0000 FE5E0000 FE600000 FE620000 |
| FE640000 FE660000 FE680000 FE6A0000 FE6C0000 |
| FE6E0000 FE700000 FE720000 FE740000 FE760000 |
| FE780000 FE7A0000 FE7C0000 FE7E0000 |
| |
| Bank # 2: INTEL 28F128J3A |
| Size: 8 MB in 64 Sectors |
| Sector Start Addresses: |
| FE800000 FE820000 FE840000 FE860000 FE880000 |
| FE8A0000 FE8C0000 FE8E0000 FE900000 FE920000 |
| FE940000 FE960000 FE980000 FE9A0000 FE9C0000 |
| FE9E0000 FEA00000 FEA20000 FEA40000 FEA60000 |
| FEA80000 FEAA0000 FEAC0000 FEAE0000 FEB00000 |
| FEB20000 FEB40000 FEB60000 FEB80000 FEBA0000 |
| FEBC0000 FEBE0000 FEC00000 FEC20000 FEC40000 |
| FEC60000 FEC80000 FECA0000 FECC0000 FECE0000 |
| FED00000 FED20000 FED40000 FED60000 FED80000 |
| FEDA0000 FEDC0000 FEDE0000 FEE00000 FEE20000 |
| FEE40000 FEE60000 FEE80000 FEEA0000 FEEC0000 |
| FEEE0000 FEF00000 (RO) FEF20000 (RO) FEF40000 FEF60000 |
| FEF80000 FEFA0000 FEFC0000 FEFE0000 (RO) |
| |
| Bank # 3: AMD AMD29F040B |
| Size: 0 MB in 7 Sectors |
| Sector Start Addresses: |
| FFF00000 (RO) FFF10000 (RO) FFF20000 (RO) FFF30000 FFF40000 |
| FFF50000 FFF60000 |
| |
| Bank # 4: AMD AMD29F040B |
| Size: 0 MB in 1 Sectors |
| Sector Start Addresses: |
| FFF70000 (RO) |
| => bdinfo |
| |
| memstart = 0xF0009800 |
| memsize = 0x10000000 |
| flashstart = 0xFFF00000 |
| flashsize = 0x01080000 |
| flashoffset = 0x00025000 |
| sramstart = 0xF0020000 |
| sramsize = 0x00008000 |
| bootflags = 0x00000001 |
| intfreq = 300 MHz |
| busfreq = 120 MHz |
| inpfreq = 30 MHz |
| flbfreq = 30 MHz |
| pcifreq = 30 MHz |
| vcofreq = 480 MHz |
| pevfreq = 81 MHz |
| ethaddr = 00:E0:0C:BC:E0:60 |
| eth1addr = 00:E0:0C:BC:E0:61 |
| IP addr = 192.162.1.2 |
| baudrate = 115200 bps |
| => printenv |
| bootargs=root=/dev/ram rw |
| bootdelay=5 |
| baudrate=115200 |
| ethaddr=00:e0:0c:bc:e0:60 |
| eth1addr=00:e0:0c:bc:e0:61 |
| ipaddr=192.162.1.2 |
| serverip=192.162.1.1 |
| gatewayip=192.162.1.1 |
| netmask=255.255.255.0 |
| hostname=Alaska |
| stdin=serial |
| stdout=serial |
| stderr=serial |
| ethact=FEC ETHERNET |
| |
| Environment size: 268/65532 bytes |
| => setenv ipaddr 192.160.1.2 |
| => setenv serverip 192.160.1.1 |
| => setenv gatewayip 192.160.1.1 |
| => saveenv |
| Saving Environment to Flash... |
| |
| . |
| Un-Protected 1 sectors |
| Erasing Flash... |
| Erasing sector 0 ... done |
| Erased 1 sectors |
| Writing to Flash... done |
| |
| . |
| Protected 1 sectors |
| => tftp 0x10000 linux.elf |
| Using FEC ETHERNET device |
| TFTP from server 192.160.1.1; our IP address is 192.160.1.2; sending through gateway 192.160.1.1 |
| Filename 'linux.elf'. |
| Load address: 0x10000 |
| Loading: invalid RARP header |
| ################################################################# |
| ################################################################# |
| ################################################################# |
| ################################################################# |
| ################################################################# |
| ################################################################# |
| ################################################################# |
| ################################################################# |
| ################################################## |
| done |
| Bytes transferred = 2917494 (2c8476 hex) |
| => bootelf |
| Loading .text @ 0x00a00000 (23820 bytes) |
| Loading .data @ 0x00a06000 (2752512 bytes) |
| Clearing .bss @ 0x00ca6000 (12764 bytes) |
| ## Starting application at 0x00a00000 ... |
| |
| Collect some entropy from RAM........done |
| loaded at: 00A00000 00CA91DC |
| zimage at: 00A06A93 00AD7756 |
| initrd at: 00AD8000 00CA5565 |
| avail ram: 00CAA000 014AA000 |
| |
| Linux/PPC load: ip=off console=ttyS0,115200 |
| Uncompressing Linux...done. |
| Now booting the kernel |
| Total memory in system: 256 MB |
| Memory BAT mapping: BAT2=256Mb, BAT3=0Mb, residual: 0Mb |
| Linux version 2.4.21-rc1 (r61688@bluesocks.sps.mot.com) (gcc version 3.3.1) #17 Wed Sep 8 11:49:16 CDT 2004 |
| Motorola Alaska port (C) 2003 Motorola, Inc. |
| CPLD rev 3 |
| CPLD switches 0x1b |
| Set Pin Mux for FEC1 |
| Set Pin Mux for FEC2 |
| Alaska Pin Multiplexing: |
| Port Configuration Register 0 = 0 |
| Port Configuration Register 1 = 0 |
| Port Configuration Register 2 = 0 |
| Port Configuration Register 3 = 50000000 |
| Port Configuration Register 3 - PCI = 51400180 |
| Setup Alaska FPGA PIC: |
| Interrupt Enable Register *(u32) = 0 |
| Interrupt Status Register = 2f0000 |
| Interrupt Enable Register in_be32 = 0 |
| Interrupt Status Register = 2f0000 |
| Interrupt Enable Register in_le32 = 0 |
| Interrupt Status Register = 2f00 |
| Interrupt Enable Register readl = 0 |
| Interrupt Status Register = 2f00 |
| Interrupt Enable Register = 0 |
| Interrupt Status Register = 2f0000 |
| Setup Alaska PCI Controller: |
| On node 0 totalpages: 65536 |
| zone(0): 65536 pages. |
| zone(1): 0 pages. |
| zone(2): 0 pages. |
| Kernel command line: ip=off console=ttyS0,115200 |
| Using XLB clock (120.00 MHz) to set up decrementer |
| Calibrating delay loop... 199.88 BogoMIPS |
| Memory: 254792k available (1476k kernel code, 708k data, 228k init, 0k highmem) |
| Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) |
| Inode cache hash table entries: 16384 (order: 5, 131072 bytes) |
| Mount cache hash table entries: 512 (order: 0, 4096 bytes) |
| Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) |
| Page-cache hash table entries: 65536 (order: 6, 262144 bytes) |
| POSIX conformance testing by UNIFIX |
| PCI: Probing PCI hardware |
| PCI: (pcibios_init) Global-Hose = 0xc029d000 |
| Scanning bus 00 |
| Fixups for bus 00 |
| Bus scan for 00 returning with max=00 |
| PCI: (pcibios_init) finished pci_scan_bus(hose->first_busno = 0, hose->ops = c01a1a74, hose = c029d000) |
| PCI: (pcibios_init) PCI Bus Count = 0 =?= Next Bus# = 1 |
| PCI: (pcibios_init@pci_fixup_irqs) finished machine dependent PCI interrupt routing! |
| PCI: bridge rsrc 81000000..81ffffff (100), parent c01a7f88 |
| PCI: bridge rsrc 84000000..87ffffff (200), parent c01a7fa4 |
| PCI: (pcibios_init) finished allocating and assigning resources! |
| initDma! |
| Using 90 DMA buffer descriptors |
| descUsed f0023600, descriptors f002360c freeSram f0024140 |
| unmask SDMA tasks: 0xf0008018 = 0x6f000000 |
| Linux NET4.0 for Linux 2.4 |
| Based upon Swansea University Computer Society NET3.039 |
| Initializing RT netlink socket |
| Starting kswapd |
| Journalled Block Device driver loaded |
| JFFS version 1.0, (C) 1999, 2000 Axis Communications AB |
| JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. |
| pty: 256 Unix98 ptys configured |
| tracek: Copyright (C) Motorola, 2003. |
| Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled |
| ttyS00 at 0xf1001008 (irq = 73) is a ST16650 |
| ttyS01 at 0xf1001010 (irq = 74) is a ST16650 |
| elp-fpanel: Copyright (C) Motorola, 2003. |
| fpanel: fpanelWait timeout |
| elp-engine: Copyright (C) Motorola, 2003. |
| Video disabled due to configuration switch 4 |
| Alpine 1284 driver: Copyright (C) Motorola, 2003. |
| 1284 disabled due to configuration switch 5 |
| Alpine USB driver: Copyright (C) Motorola, 2003. |
| OK |
| USB: Descriptor download completed OK |
| enable_irq(41) unbalanced |
| enable_irq(75) unbalanced |
| elp-dmaram: Copyright (C) Motorola, 2003. |
| Total memory in system: 256 MB |
| elp_dmaram: offset is 0x10000000, size is 0 |
| Xicor NVRAM driver: Copyright (C) Motorola, 2003. |
| elp-video: Copyright (C) Motorola, 2003. |
| Video disabled due to configuration switch 4 |
| elp-pfm: Copyright (C) Motorola, 2003. |
| paddle: Copyright (C) Motorola, 2001, present. |
| RAMDISK driver initialized: 16 RAM disks of 12288K size 1024 blocksize |
| loop: loaded (max 8 devices) |
| PPP generic driver version 2.4.2 |
| PPP Deflate Compression module registered |
| Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4 |
| ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx |
| init_alaska_mtd: chip probing count 0 |
| cfi_cmdset_0001: Erase suspend on write enabled |
| Using buffer write method |
| init_alaska_mtd: bank1, name:ALASKA0, size:16777216bytes |
| ALASKA flash0: Using Static image partition definition |
| Creating 3 MTD partitions on "ALASKA0": |
| 0x00000000-0x00280000 : "kernel" |
| 0x00280000-0x00fe0000 : "user" |
| 0x00fe0000-0x01000000 : "signature" |
| mgt_fec_module_init |
| mgt_fec_init() |
| mgt_fec_init |
| mgt_init_fec_dev(0xc05f6000,0) |
| dev c05f6000 fec_priv c05f6160 fec f0009000 |
| mgt_init_fec_dev(0xc05f6800,1) |
| dev c05f6800 fec_priv c05f6960 fec f0009800 |
| NET4: Linux TCP/IP 1.0 for NET4.0 |
| IP Protocols: ICMP, UDP, TCP, IGMP |
| IP: routing cache hash table of 2048 buckets, 16Kbytes |
| TCP: Hash tables configured (established 16384 bind 32768) |
| NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. |
| RAMDISK: Compressed image found at block 0 |
| Freeing initrd memory: 1845k freed |
| JFFS: Trying to mount a non-mtd device. |
| VFS: Mounted root (romfs filesystem) readonly. |
| Freeing unused kernel memory: 228k init |
| INIT: version 2.78 booting |
| INIT: Entering runlevel: 1 |
| "Space, a great big place of unknown stuff." -Dexter, for our MotD. |
| [01/Jan/1970:00:00:01 +0000] boa: server version Boa/0.94.8.3 |
| [01/Jan/1970:00:00:01 +0000] boa: server built Sep 7 2004 at 17:40:55. |
| [01/Jan/1970:00:00:01 +0000] boa: starting server pid=28, port 80 |
| Mounting flash filesystem, will take a minute... |
| /etc/rc: line 30: /dev/lp0: No such devish-2.05b# |
| sh-2.05b# ifup eth0 |
| client (v0.9.9-pre) started |
| adapter index 2 |
| adapter hardware address 00:e0:0c:bc:e0:60 |
| execle'ing /usr/share/udhcpc/default.script |
| /sbin/ifconfig eth0 |
| eth0 Link encap:Ethernet HWaddr 00:E0:0C:BC:E0:60 |
| BROADCAST MULTICAST MTU:1500 Metric:1 |
| mgt_fec_open |
| Rfec request irq |
| X fec_open: rcv_ring_size 8, xmt_ring_size 8 |
| packmgt_fec_open(): call netif_start_queue() |
| ets:0 errors:0 dropped:0 overruns:0 frame:0 |
| TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 |
| collisions:0 txqueuelen:100 |
| RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) |
| Base address:0x9000 |
| |
| /sbin/ifconfig eth0 up |
| entering raw listen mode |
| Opening raw socket on ifindex 2 |
| adding option 0x35 |
| adding option 0x3d |
| adding option 0x3c |
| Sending discover... |
| Waiting on select... |
| unrelated/bogus packet |
| Waiting on select... |
| oooooh!!! got some! |
| adding option 0x35 |
| adding option 0x3d |
| adding option 0x3c |
| adding option 0x32 |
| adding option 0x36 |
| Sending select for 163.12.48.146... |
| Waiting on select... |
| oooooh!!! got some! |
| Waiting on select... |
| oooooh!!! got some! |
| Lease of 163.12.48.146 obtained, lease time 345600 |
| execle'ing /usr/share/udhcpc/default.script |
| /sbin/ifconfig eth0 163.12.48.146 netmask 255.255.254.0 |
| /sbin/ifconfig eth0 up |
| deleting routers |
| /sbin/route del default |
| /sbin/route add default gw 163.12.49.254 dev eth0 |
| adding dns 163.12.252.230 |
| adding dns 192.55.22.4 |
| adding dns 192.5.249.4 |
| entering none listen mode |
| sh-2.05b# |
| |
| 5. REPROGRAM U-BOOT |
| =================== |
| 5.1 Reprogram u-boot (boot from AMD) |
| 1. Unprotect the boot sector |
| => protect off bank 3 |
| 2. Download new u-boot binary file |
| => tftp 0x10000 u-boot.bin |
| 3. Erase bootsector (max 7 sectors) |
| => erase 0xfff00000 0xfff6ffff |
| 4. Program the u-boot to flash |
| => cp.b 0x10000 0xfff00000 |
| 5. Reset for the new u-boot to take place |
| => reset |
| |
| 5.2 Reprogram u-boot (boot from AMD program at INTEL) |
| 1. Unprotect the boot sector |
| => protect off bank 2 |
| 2. Download new u-boot binary file |
| => tftp 0x10000 u-boot.bin |
| 3. Erase bootsector (max 7 sectors) |
| => erase 0xfef00000 0xfefdffff |
| 4. Program the u-boot to flash |
| => cp.b 0x10000 0xfef00000 |
| 5. Reset for the new u-boot to take place |
| => reset |
| |
| 5.3 Reprogram u-boot (boot from INTEL) |
| 1. Unprotect the boot sector |
| => protect off bank 4 |
| 2. Download new u-boot binary file |
| => tftp 0x10000 u-boot.bin |
| 3. Erase bootsector (max 7 sectors) |
| => erase 0xfff00000 0xfffdffff |
| 4. Program the u-boot to flash |
| => cp.b 0x10000 0xfff00000 |
| 5. Reset for the new u-boot to take place |
| => reset |
| |
| 5.4 Reprogram u-boot (boot from INTEL program at AMD) |
| 1. Unprotect the boot sector |
| => protect off bank 1 |
| 2. Download new u-boot binary file |
| => tftp 0x10000 u-boot.bin |
| 3. Erase bootsector (max 7 sectors) |
| => erase 0xfe080000 0xfe0effff |
| 4. Program the u-boot to flash |
| => cp.b 0x10000 0xfe080000 |
| 5. Reset for the new u-boot to take place |
| => reset |
