| /* | |
| * Copyright (C) 2005-2006 Atmel Corporation | |
| * | |
| * SPDX-License-Identifier: GPL-2.0+ | |
| */ | |
| #include <common.h> | |
| /* | |
| * The u-boot networking stack is a little weird. It seems like the | |
| * networking core allocates receive buffers up front without any | |
| * regard to the hardware that's supposed to actually receive those | |
| * packets. | |
| * | |
| * The MACB receives packets into 128-byte receive buffers, so the | |
| * buffers allocated by the core isn't very practical to use. We'll | |
| * allocate our own, but we need one such buffer in case a packet | |
| * wraps around the DMA ring so that we have to copy it. | |
| * | |
| * Therefore, define CONFIG_SYS_RX_ETH_BUFFER to 1 in the board-specific | |
| * configuration header. This way, the core allocates one RX buffer | |
| * and one TX buffer, each of which can hold a ethernet packet of | |
| * maximum size. | |
| * | |
| * For some reason, the networking core unconditionally specifies a | |
| * 32-byte packet "alignment" (which really should be called | |
| * "padding"). MACB shouldn't need that, but we'll refrain from any | |
| * core modifications here... | |
| */ | |
| #include <net.h> | |
| #include <netdev.h> | |
| #include <malloc.h> | |
| #include <miiphy.h> | |
| #include <linux/mii.h> | |
| #include <asm/io.h> | |
| #include <asm/dma-mapping.h> | |
| #include <asm/arch/clk.h> | |
| #include <asm-generic/errno.h> | |
| #include "macb.h" | |
| #define CONFIG_SYS_MACB_RX_BUFFER_SIZE 4096 | |
| #define CONFIG_SYS_MACB_RX_RING_SIZE (CONFIG_SYS_MACB_RX_BUFFER_SIZE / 128) | |
| #define CONFIG_SYS_MACB_TX_RING_SIZE 16 | |
| #define CONFIG_SYS_MACB_TX_TIMEOUT 1000 | |
| #define CONFIG_SYS_MACB_AUTONEG_TIMEOUT 5000000 | |
| struct macb_dma_desc { | |
| u32 addr; | |
| u32 ctrl; | |
| }; | |
| #define RXADDR_USED 0x00000001 | |
| #define RXADDR_WRAP 0x00000002 | |
| #define RXBUF_FRMLEN_MASK 0x00000fff | |
| #define RXBUF_FRAME_START 0x00004000 | |
| #define RXBUF_FRAME_END 0x00008000 | |
| #define RXBUF_TYPEID_MATCH 0x00400000 | |
| #define RXBUF_ADDR4_MATCH 0x00800000 | |
| #define RXBUF_ADDR3_MATCH 0x01000000 | |
| #define RXBUF_ADDR2_MATCH 0x02000000 | |
| #define RXBUF_ADDR1_MATCH 0x04000000 | |
| #define RXBUF_BROADCAST 0x80000000 | |
| #define TXBUF_FRMLEN_MASK 0x000007ff | |
| #define TXBUF_FRAME_END 0x00008000 | |
| #define TXBUF_NOCRC 0x00010000 | |
| #define TXBUF_EXHAUSTED 0x08000000 | |
| #define TXBUF_UNDERRUN 0x10000000 | |
| #define TXBUF_MAXRETRY 0x20000000 | |
| #define TXBUF_WRAP 0x40000000 | |
| #define TXBUF_USED 0x80000000 | |
| struct macb_device { | |
| void *regs; | |
| unsigned int rx_tail; | |
| unsigned int tx_head; | |
| unsigned int tx_tail; | |
| void *rx_buffer; | |
| void *tx_buffer; | |
| struct macb_dma_desc *rx_ring; | |
| struct macb_dma_desc *tx_ring; | |
| unsigned long rx_buffer_dma; | |
| unsigned long rx_ring_dma; | |
| unsigned long tx_ring_dma; | |
| const struct device *dev; | |
| struct eth_device netdev; | |
| unsigned short phy_addr; | |
| struct mii_dev *bus; | |
| }; | |
| #define to_macb(_nd) container_of(_nd, struct macb_device, netdev) | |
| static int macb_is_gem(struct macb_device *macb) | |
| { | |
| return MACB_BFEXT(IDNUM, macb_readl(macb, MID)) == 0x2; | |
| } | |
| static void macb_mdio_write(struct macb_device *macb, u8 reg, u16 value) | |
| { | |
| unsigned long netctl; | |
| unsigned long netstat; | |
| unsigned long frame; | |
| netctl = macb_readl(macb, NCR); | |
| netctl |= MACB_BIT(MPE); | |
| macb_writel(macb, NCR, netctl); | |
| frame = (MACB_BF(SOF, 1) | |
| | MACB_BF(RW, 1) | |
| | MACB_BF(PHYA, macb->phy_addr) | |
| | MACB_BF(REGA, reg) | |
| | MACB_BF(CODE, 2) | |
| | MACB_BF(DATA, value)); | |
| macb_writel(macb, MAN, frame); | |
| do { | |
| netstat = macb_readl(macb, NSR); | |
| } while (!(netstat & MACB_BIT(IDLE))); | |
| netctl = macb_readl(macb, NCR); | |
| netctl &= ~MACB_BIT(MPE); | |
| macb_writel(macb, NCR, netctl); | |
| } | |
| static u16 macb_mdio_read(struct macb_device *macb, u8 reg) | |
| { | |
| unsigned long netctl; | |
| unsigned long netstat; | |
| unsigned long frame; | |
| netctl = macb_readl(macb, NCR); | |
| netctl |= MACB_BIT(MPE); | |
| macb_writel(macb, NCR, netctl); | |
| frame = (MACB_BF(SOF, 1) | |
| | MACB_BF(RW, 2) | |
| | MACB_BF(PHYA, macb->phy_addr) | |
| | MACB_BF(REGA, reg) | |
| | MACB_BF(CODE, 2)); | |
| macb_writel(macb, MAN, frame); | |
| do { | |
| netstat = macb_readl(macb, NSR); | |
| } while (!(netstat & MACB_BIT(IDLE))); | |
| frame = macb_readl(macb, MAN); | |
| netctl = macb_readl(macb, NCR); | |
| netctl &= ~MACB_BIT(MPE); | |
| macb_writel(macb, NCR, netctl); | |
| return MACB_BFEXT(DATA, frame); | |
| } | |
| void __weak arch_get_mdio_control(const char *name) | |
| { | |
| return; | |
| } | |
| #if defined(CONFIG_CMD_MII) || defined(CONFIG_PHYLIB) | |
| int macb_miiphy_read(const char *devname, u8 phy_adr, u8 reg, u16 *value) | |
| { | |
| struct eth_device *dev = eth_get_dev_by_name(devname); | |
| struct macb_device *macb = to_macb(dev); | |
| if ( macb->phy_addr != phy_adr ) | |
| return -1; | |
| arch_get_mdio_control(devname); | |
| *value = macb_mdio_read(macb, reg); | |
| return 0; | |
| } | |
| int macb_miiphy_write(const char *devname, u8 phy_adr, u8 reg, u16 value) | |
| { | |
| struct eth_device *dev = eth_get_dev_by_name(devname); | |
| struct macb_device *macb = to_macb(dev); | |
| if ( macb->phy_addr != phy_adr ) | |
| return -1; | |
| arch_get_mdio_control(devname); | |
| macb_mdio_write(macb, reg, value); | |
| return 0; | |
| } | |
| #endif | |
| #if defined(CONFIG_CMD_NET) | |
| static int macb_send(struct eth_device *netdev, void *packet, int length) | |
| { | |
| struct macb_device *macb = to_macb(netdev); | |
| unsigned long paddr, ctrl; | |
| unsigned int tx_head = macb->tx_head; | |
| int i; | |
| paddr = dma_map_single(packet, length, DMA_TO_DEVICE); | |
| ctrl = length & TXBUF_FRMLEN_MASK; | |
| ctrl |= TXBUF_FRAME_END; | |
| if (tx_head == (CONFIG_SYS_MACB_TX_RING_SIZE - 1)) { | |
| ctrl |= TXBUF_WRAP; | |
| macb->tx_head = 0; | |
| } else | |
| macb->tx_head++; | |
| macb->tx_ring[tx_head].ctrl = ctrl; | |
| macb->tx_ring[tx_head].addr = paddr; | |
| barrier(); | |
| macb_writel(macb, NCR, MACB_BIT(TE) | MACB_BIT(RE) | MACB_BIT(TSTART)); | |
| /* | |
| * I guess this is necessary because the networking core may | |
| * re-use the transmit buffer as soon as we return... | |
| */ | |
| for (i = 0; i <= CONFIG_SYS_MACB_TX_TIMEOUT; i++) { | |
| barrier(); | |
| ctrl = macb->tx_ring[tx_head].ctrl; | |
| if (ctrl & TXBUF_USED) | |
| break; | |
| udelay(1); | |
| } | |
| dma_unmap_single(packet, length, paddr); | |
| if (i <= CONFIG_SYS_MACB_TX_TIMEOUT) { | |
| if (ctrl & TXBUF_UNDERRUN) | |
| printf("%s: TX underrun\n", netdev->name); | |
| if (ctrl & TXBUF_EXHAUSTED) | |
| printf("%s: TX buffers exhausted in mid frame\n", | |
| netdev->name); | |
| } else { | |
| printf("%s: TX timeout\n", netdev->name); | |
| } | |
| /* No one cares anyway */ | |
| return 0; | |
| } | |
| static void reclaim_rx_buffers(struct macb_device *macb, | |
| unsigned int new_tail) | |
| { | |
| unsigned int i; | |
| i = macb->rx_tail; | |
| while (i > new_tail) { | |
| macb->rx_ring[i].addr &= ~RXADDR_USED; | |
| i++; | |
| if (i > CONFIG_SYS_MACB_RX_RING_SIZE) | |
| i = 0; | |
| } | |
| while (i < new_tail) { | |
| macb->rx_ring[i].addr &= ~RXADDR_USED; | |
| i++; | |
| } | |
| barrier(); | |
| macb->rx_tail = new_tail; | |
| } | |
| static int macb_recv(struct eth_device *netdev) | |
| { | |
| struct macb_device *macb = to_macb(netdev); | |
| unsigned int rx_tail = macb->rx_tail; | |
| void *buffer; | |
| int length; | |
| int wrapped = 0; | |
| u32 status; | |
| for (;;) { | |
| if (!(macb->rx_ring[rx_tail].addr & RXADDR_USED)) | |
| return -1; | |
| status = macb->rx_ring[rx_tail].ctrl; | |
| if (status & RXBUF_FRAME_START) { | |
| if (rx_tail != macb->rx_tail) | |
| reclaim_rx_buffers(macb, rx_tail); | |
| wrapped = 0; | |
| } | |
| if (status & RXBUF_FRAME_END) { | |
| buffer = macb->rx_buffer + 128 * macb->rx_tail; | |
| length = status & RXBUF_FRMLEN_MASK; | |
| if (wrapped) { | |
| unsigned int headlen, taillen; | |
| headlen = 128 * (CONFIG_SYS_MACB_RX_RING_SIZE | |
| - macb->rx_tail); | |
| taillen = length - headlen; | |
| memcpy((void *)NetRxPackets[0], | |
| buffer, headlen); | |
| memcpy((void *)NetRxPackets[0] + headlen, | |
| macb->rx_buffer, taillen); | |
| buffer = (void *)NetRxPackets[0]; | |
| } | |
| NetReceive(buffer, length); | |
| if (++rx_tail >= CONFIG_SYS_MACB_RX_RING_SIZE) | |
| rx_tail = 0; | |
| reclaim_rx_buffers(macb, rx_tail); | |
| } else { | |
| if (++rx_tail >= CONFIG_SYS_MACB_RX_RING_SIZE) { | |
| wrapped = 1; | |
| rx_tail = 0; | |
| } | |
| } | |
| barrier(); | |
| } | |
| return 0; | |
| } | |
| static void macb_phy_reset(struct macb_device *macb) | |
| { | |
| struct eth_device *netdev = &macb->netdev; | |
| int i; | |
| u16 status, adv; | |
| adv = ADVERTISE_CSMA | ADVERTISE_ALL; | |
| macb_mdio_write(macb, MII_ADVERTISE, adv); | |
| printf("%s: Starting autonegotiation...\n", netdev->name); | |
| macb_mdio_write(macb, MII_BMCR, (BMCR_ANENABLE | |
| | BMCR_ANRESTART)); | |
| for (i = 0; i < CONFIG_SYS_MACB_AUTONEG_TIMEOUT / 100; i++) { | |
| status = macb_mdio_read(macb, MII_BMSR); | |
| if (status & BMSR_ANEGCOMPLETE) | |
| break; | |
| udelay(100); | |
| } | |
| if (status & BMSR_ANEGCOMPLETE) | |
| printf("%s: Autonegotiation complete\n", netdev->name); | |
| else | |
| printf("%s: Autonegotiation timed out (status=0x%04x)\n", | |
| netdev->name, status); | |
| } | |
| #ifdef CONFIG_MACB_SEARCH_PHY | |
| static int macb_phy_find(struct macb_device *macb) | |
| { | |
| int i; | |
| u16 phy_id; | |
| /* Search for PHY... */ | |
| for (i = 0; i < 32; i++) { | |
| macb->phy_addr = i; | |
| phy_id = macb_mdio_read(macb, MII_PHYSID1); | |
| if (phy_id != 0xffff) { | |
| printf("%s: PHY present at %d\n", macb->netdev.name, i); | |
| return 1; | |
| } | |
| } | |
| /* PHY isn't up to snuff */ | |
| printf("%s: PHY not found\n", macb->netdev.name); | |
| return 0; | |
| } | |
| #endif /* CONFIG_MACB_SEARCH_PHY */ | |
| static int macb_phy_init(struct macb_device *macb) | |
| { | |
| struct eth_device *netdev = &macb->netdev; | |
| #ifdef CONFIG_PHYLIB | |
| struct phy_device *phydev; | |
| #endif | |
| u32 ncfgr; | |
| u16 phy_id, status, adv, lpa; | |
| int media, speed, duplex; | |
| int i; | |
| arch_get_mdio_control(netdev->name); | |
| #ifdef CONFIG_MACB_SEARCH_PHY | |
| /* Auto-detect phy_addr */ | |
| if (!macb_phy_find(macb)) { | |
| return 0; | |
| } | |
| #endif /* CONFIG_MACB_SEARCH_PHY */ | |
| /* Check if the PHY is up to snuff... */ | |
| phy_id = macb_mdio_read(macb, MII_PHYSID1); | |
| if (phy_id == 0xffff) { | |
| printf("%s: No PHY present\n", netdev->name); | |
| return 0; | |
| } | |
| #ifdef CONFIG_PHYLIB | |
| /* need to consider other phy interface mode */ | |
| phydev = phy_connect(macb->bus, macb->phy_addr, netdev, | |
| PHY_INTERFACE_MODE_RGMII); | |
| if (!phydev) { | |
| printf("phy_connect failed\n"); | |
| return -ENODEV; | |
| } | |
| phy_config(phydev); | |
| #endif | |
| status = macb_mdio_read(macb, MII_BMSR); | |
| if (!(status & BMSR_LSTATUS)) { | |
| /* Try to re-negotiate if we don't have link already. */ | |
| macb_phy_reset(macb); | |
| for (i = 0; i < CONFIG_SYS_MACB_AUTONEG_TIMEOUT / 100; i++) { | |
| status = macb_mdio_read(macb, MII_BMSR); | |
| if (status & BMSR_LSTATUS) | |
| break; | |
| udelay(100); | |
| } | |
| } | |
| if (!(status & BMSR_LSTATUS)) { | |
| printf("%s: link down (status: 0x%04x)\n", | |
| netdev->name, status); | |
| return 0; | |
| } | |
| /* First check for GMAC */ | |
| if (macb_is_gem(macb)) { | |
| lpa = macb_mdio_read(macb, MII_STAT1000); | |
| if (lpa & (1 << 11)) { | |
| speed = 1000; | |
| duplex = 1; | |
| } else { | |
| if (lpa & (1 << 10)) { | |
| speed = 1000; | |
| duplex = 1; | |
| } else { | |
| speed = 0; | |
| } | |
| } | |
| if (speed == 1000) { | |
| printf("%s: link up, %dMbps %s-duplex (lpa: 0x%04x)\n", | |
| netdev->name, | |
| speed, | |
| duplex ? "full" : "half", | |
| lpa); | |
| ncfgr = macb_readl(macb, NCFGR); | |
| ncfgr &= ~(GEM_BIT(GBE) | MACB_BIT(SPD) | MACB_BIT(FD)); | |
| if (speed) | |
| ncfgr |= GEM_BIT(GBE); | |
| if (duplex) | |
| ncfgr |= MACB_BIT(FD); | |
| macb_writel(macb, NCFGR, ncfgr); | |
| return 1; | |
| } | |
| } | |
| /* fall back for EMAC checking */ | |
| adv = macb_mdio_read(macb, MII_ADVERTISE); | |
| lpa = macb_mdio_read(macb, MII_LPA); | |
| media = mii_nway_result(lpa & adv); | |
| speed = (media & (ADVERTISE_100FULL | ADVERTISE_100HALF) | |
| ? 1 : 0); | |
| duplex = (media & ADVERTISE_FULL) ? 1 : 0; | |
| printf("%s: link up, %sMbps %s-duplex (lpa: 0x%04x)\n", | |
| netdev->name, | |
| speed ? "100" : "10", | |
| duplex ? "full" : "half", | |
| lpa); | |
| ncfgr = macb_readl(macb, NCFGR); | |
| ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD)); | |
| if (speed) | |
| ncfgr |= MACB_BIT(SPD); | |
| if (duplex) | |
| ncfgr |= MACB_BIT(FD); | |
| macb_writel(macb, NCFGR, ncfgr); | |
| return 1; | |
| } | |
| static int macb_init(struct eth_device *netdev, bd_t *bd) | |
| { | |
| struct macb_device *macb = to_macb(netdev); | |
| unsigned long paddr; | |
| int i; | |
| /* | |
| * macb_halt should have been called at some point before now, | |
| * so we'll assume the controller is idle. | |
| */ | |
| /* initialize DMA descriptors */ | |
| paddr = macb->rx_buffer_dma; | |
| for (i = 0; i < CONFIG_SYS_MACB_RX_RING_SIZE; i++) { | |
| if (i == (CONFIG_SYS_MACB_RX_RING_SIZE - 1)) | |
| paddr |= RXADDR_WRAP; | |
| macb->rx_ring[i].addr = paddr; | |
| macb->rx_ring[i].ctrl = 0; | |
| paddr += 128; | |
| } | |
| for (i = 0; i < CONFIG_SYS_MACB_TX_RING_SIZE; i++) { | |
| macb->tx_ring[i].addr = 0; | |
| if (i == (CONFIG_SYS_MACB_TX_RING_SIZE - 1)) | |
| macb->tx_ring[i].ctrl = TXBUF_USED | TXBUF_WRAP; | |
| else | |
| macb->tx_ring[i].ctrl = TXBUF_USED; | |
| } | |
| macb->rx_tail = macb->tx_head = macb->tx_tail = 0; | |
| macb_writel(macb, RBQP, macb->rx_ring_dma); | |
| macb_writel(macb, TBQP, macb->tx_ring_dma); | |
| if (macb_is_gem(macb)) { | |
| #ifdef CONFIG_RGMII | |
| gem_writel(macb, UR, GEM_BIT(RGMII)); | |
| #else | |
| gem_writel(macb, UR, 0); | |
| #endif | |
| } else { | |
| /* choose RMII or MII mode. This depends on the board */ | |
| #ifdef CONFIG_RMII | |
| #ifdef CONFIG_AT91FAMILY | |
| macb_writel(macb, USRIO, MACB_BIT(RMII) | MACB_BIT(CLKEN)); | |
| #else | |
| macb_writel(macb, USRIO, 0); | |
| #endif | |
| #else | |
| #ifdef CONFIG_AT91FAMILY | |
| macb_writel(macb, USRIO, MACB_BIT(CLKEN)); | |
| #else | |
| macb_writel(macb, USRIO, MACB_BIT(MII)); | |
| #endif | |
| #endif /* CONFIG_RMII */ | |
| } | |
| if (!macb_phy_init(macb)) | |
| return -1; | |
| /* Enable TX and RX */ | |
| macb_writel(macb, NCR, MACB_BIT(TE) | MACB_BIT(RE)); | |
| return 0; | |
| } | |
| static void macb_halt(struct eth_device *netdev) | |
| { | |
| struct macb_device *macb = to_macb(netdev); | |
| u32 ncr, tsr; | |
| /* Halt the controller and wait for any ongoing transmission to end. */ | |
| ncr = macb_readl(macb, NCR); | |
| ncr |= MACB_BIT(THALT); | |
| macb_writel(macb, NCR, ncr); | |
| do { | |
| tsr = macb_readl(macb, TSR); | |
| } while (tsr & MACB_BIT(TGO)); | |
| /* Disable TX and RX, and clear statistics */ | |
| macb_writel(macb, NCR, MACB_BIT(CLRSTAT)); | |
| } | |
| static int macb_write_hwaddr(struct eth_device *dev) | |
| { | |
| struct macb_device *macb = to_macb(dev); | |
| u32 hwaddr_bottom; | |
| u16 hwaddr_top; | |
| /* set hardware address */ | |
| hwaddr_bottom = dev->enetaddr[0] | dev->enetaddr[1] << 8 | | |
| dev->enetaddr[2] << 16 | dev->enetaddr[3] << 24; | |
| macb_writel(macb, SA1B, hwaddr_bottom); | |
| hwaddr_top = dev->enetaddr[4] | dev->enetaddr[5] << 8; | |
| macb_writel(macb, SA1T, hwaddr_top); | |
| return 0; | |
| } | |
| static u32 macb_mdc_clk_div(int id, struct macb_device *macb) | |
| { | |
| u32 config; | |
| unsigned long macb_hz = get_macb_pclk_rate(id); | |
| if (macb_hz < 20000000) | |
| config = MACB_BF(CLK, MACB_CLK_DIV8); | |
| else if (macb_hz < 40000000) | |
| config = MACB_BF(CLK, MACB_CLK_DIV16); | |
| else if (macb_hz < 80000000) | |
| config = MACB_BF(CLK, MACB_CLK_DIV32); | |
| else | |
| config = MACB_BF(CLK, MACB_CLK_DIV64); | |
| return config; | |
| } | |
| static u32 gem_mdc_clk_div(int id, struct macb_device *macb) | |
| { | |
| u32 config; | |
| unsigned long macb_hz = get_macb_pclk_rate(id); | |
| if (macb_hz < 20000000) | |
| config = GEM_BF(CLK, GEM_CLK_DIV8); | |
| else if (macb_hz < 40000000) | |
| config = GEM_BF(CLK, GEM_CLK_DIV16); | |
| else if (macb_hz < 80000000) | |
| config = GEM_BF(CLK, GEM_CLK_DIV32); | |
| else if (macb_hz < 120000000) | |
| config = GEM_BF(CLK, GEM_CLK_DIV48); | |
| else if (macb_hz < 160000000) | |
| config = GEM_BF(CLK, GEM_CLK_DIV64); | |
| else | |
| config = GEM_BF(CLK, GEM_CLK_DIV96); | |
| return config; | |
| } | |
| /* | |
| * Get the DMA bus width field of the network configuration register that we | |
| * should program. We find the width from decoding the design configuration | |
| * register to find the maximum supported data bus width. | |
| */ | |
| static u32 macb_dbw(struct macb_device *macb) | |
| { | |
| switch (GEM_BFEXT(DBWDEF, gem_readl(macb, DCFG1))) { | |
| case 4: | |
| return GEM_BF(DBW, GEM_DBW128); | |
| case 2: | |
| return GEM_BF(DBW, GEM_DBW64); | |
| case 1: | |
| default: | |
| return GEM_BF(DBW, GEM_DBW32); | |
| } | |
| } | |
| int macb_eth_initialize(int id, void *regs, unsigned int phy_addr) | |
| { | |
| struct macb_device *macb; | |
| struct eth_device *netdev; | |
| u32 ncfgr; | |
| macb = malloc(sizeof(struct macb_device)); | |
| if (!macb) { | |
| printf("Error: Failed to allocate memory for MACB%d\n", id); | |
| return -1; | |
| } | |
| memset(macb, 0, sizeof(struct macb_device)); | |
| netdev = &macb->netdev; | |
| macb->rx_buffer = dma_alloc_coherent(CONFIG_SYS_MACB_RX_BUFFER_SIZE, | |
| &macb->rx_buffer_dma); | |
| macb->rx_ring = dma_alloc_coherent(CONFIG_SYS_MACB_RX_RING_SIZE | |
| * sizeof(struct macb_dma_desc), | |
| &macb->rx_ring_dma); | |
| macb->tx_ring = dma_alloc_coherent(CONFIG_SYS_MACB_TX_RING_SIZE | |
| * sizeof(struct macb_dma_desc), | |
| &macb->tx_ring_dma); | |
| macb->regs = regs; | |
| macb->phy_addr = phy_addr; | |
| if (macb_is_gem(macb)) | |
| sprintf(netdev->name, "gmac%d", id); | |
| else | |
| sprintf(netdev->name, "macb%d", id); | |
| netdev->init = macb_init; | |
| netdev->halt = macb_halt; | |
| netdev->send = macb_send; | |
| netdev->recv = macb_recv; | |
| netdev->write_hwaddr = macb_write_hwaddr; | |
| /* | |
| * Do some basic initialization so that we at least can talk | |
| * to the PHY | |
| */ | |
| if (macb_is_gem(macb)) { | |
| ncfgr = gem_mdc_clk_div(id, macb); | |
| ncfgr |= macb_dbw(macb); | |
| } else { | |
| ncfgr = macb_mdc_clk_div(id, macb); | |
| } | |
| macb_writel(macb, NCFGR, ncfgr); | |
| eth_register(netdev); | |
| #if defined(CONFIG_CMD_MII) || defined(CONFIG_PHYLIB) | |
| miiphy_register(netdev->name, macb_miiphy_read, macb_miiphy_write); | |
| macb->bus = miiphy_get_dev_by_name(netdev->name); | |
| #endif | |
| return 0; | |
| } | |
| #endif |