| /* | |
| * Configuation settings for the Freescale MCF54455 EVB board. | |
| * | |
| * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. | |
| * TsiChung Liew (Tsi-Chung.Liew@freescale.com) | |
| * | |
| * SPDX-License-Identifier: GPL-2.0+ | |
| */ | |
| /* | |
| * board/config.h - configuration options, board specific | |
| */ | |
| #ifndef _M54455EVB_H | |
| #define _M54455EVB_H | |
| /* | |
| * High Level Configuration Options | |
| * (easy to change) | |
| */ | |
| #define CONFIG_MCF5445x /* define processor family */ | |
| #define CONFIG_M54455 /* define processor type */ | |
| #define CONFIG_M54455EVB /* M54455EVB board */ | |
| #define CONFIG_MCFUART | |
| #define CONFIG_SYS_UART_PORT (0) | |
| #define CONFIG_BAUDRATE 115200 | |
| #undef CONFIG_WATCHDOG | |
| #define CONFIG_TIMESTAMP /* Print image info with timestamp */ | |
| /* | |
| * BOOTP options | |
| */ | |
| #define CONFIG_BOOTP_BOOTFILESIZE | |
| #define CONFIG_BOOTP_BOOTPATH | |
| #define CONFIG_BOOTP_GATEWAY | |
| #define CONFIG_BOOTP_HOSTNAME | |
| /* Command line configuration */ | |
| #include <config_cmd_default.h> | |
| #define CONFIG_CMD_BOOTD | |
| #define CONFIG_CMD_CACHE | |
| #define CONFIG_CMD_DATE | |
| #define CONFIG_CMD_DHCP | |
| #define CONFIG_CMD_ELF | |
| #define CONFIG_CMD_EXT2 | |
| #define CONFIG_CMD_FAT | |
| #define CONFIG_CMD_FLASH | |
| #define CONFIG_CMD_I2C | |
| #define CONFIG_CMD_IDE | |
| #define CONFIG_CMD_JFFS2 | |
| #define CONFIG_CMD_MEMORY | |
| #define CONFIG_CMD_MISC | |
| #define CONFIG_CMD_MII | |
| #define CONFIG_CMD_NET | |
| #undef CONFIG_CMD_PCI | |
| #define CONFIG_CMD_PING | |
| #define CONFIG_CMD_REGINFO | |
| #define CONFIG_CMD_SPI | |
| #define CONFIG_CMD_SF | |
| #undef CONFIG_CMD_LOADB | |
| #undef CONFIG_CMD_LOADS | |
| /* Network configuration */ | |
| #define CONFIG_MCFFEC | |
| #ifdef CONFIG_MCFFEC | |
| # define CONFIG_MII 1 | |
| # define CONFIG_MII_INIT 1 | |
| # define CONFIG_SYS_DISCOVER_PHY | |
| # define CONFIG_SYS_RX_ETH_BUFFER 8 | |
| # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN | |
| # define CONFIG_SYS_FEC0_PINMUX 0 | |
| # define CONFIG_SYS_FEC1_PINMUX 0 | |
| # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE | |
| # define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_IOBASE | |
| # define MCFFEC_TOUT_LOOP 50000 | |
| # define CONFIG_HAS_ETH1 | |
| # define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ | |
| # define CONFIG_BOOTARGS "root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=physmap-flash.0:5M(kernel)ro,-(jffs2)" | |
| # define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 | |
| # define CONFIG_ETH1ADDR 00:e0:0c:bc:e5:61 | |
| # define CONFIG_ETHPRIME "FEC0" | |
| # define CONFIG_IPADDR 192.162.1.2 | |
| # define CONFIG_NETMASK 255.255.255.0 | |
| # define CONFIG_SERVERIP 192.162.1.1 | |
| # define CONFIG_GATEWAYIP 192.162.1.1 | |
| # define CONFIG_OVERWRITE_ETHADDR_ONCE | |
| /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ | |
| # ifndef CONFIG_SYS_DISCOVER_PHY | |
| # define FECDUPLEX FULL | |
| # define FECSPEED _100BASET | |
| # else | |
| # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN | |
| # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN | |
| # endif | |
| # endif /* CONFIG_SYS_DISCOVER_PHY */ | |
| #endif | |
| #define CONFIG_HOSTNAME M54455EVB | |
| #ifdef CONFIG_SYS_STMICRO_BOOT | |
| /* ST Micro serial flash */ | |
| #define CONFIG_SYS_LOAD_ADDR2 0x40010013 | |
| #define CONFIG_EXTRA_ENV_SETTINGS \ | |
| "netdev=eth0\0" \ | |
| "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ | |
| "loadaddr=0x40010000\0" \ | |
| "sbfhdr=sbfhdr.bin\0" \ | |
| "uboot=u-boot.bin\0" \ | |
| "load=tftp ${loadaddr} ${sbfhdr};" \ | |
| "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \ | |
| "upd=run load; run prog\0" \ | |
| "prog=sf probe 0:1 1000000 3;" \ | |
| "sf erase 0 30000;" \ | |
| "sf write ${loadaddr} 0 0x30000;" \ | |
| "save\0" \ | |
| "" | |
| #else | |
| /* Atmel and Intel */ | |
| #ifdef CONFIG_SYS_ATMEL_BOOT | |
| # define CONFIG_SYS_UBOOT_END 0x0403FFFF | |
| #elif defined(CONFIG_SYS_INTEL_BOOT) | |
| # define CONFIG_SYS_UBOOT_END 0x3FFFF | |
| #endif | |
| #define CONFIG_EXTRA_ENV_SETTINGS \ | |
| "netdev=eth0\0" \ | |
| "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ | |
| "loadaddr=0x40010000\0" \ | |
| "uboot=u-boot.bin\0" \ | |
| "load=tftp ${loadaddr} ${uboot}\0" \ | |
| "upd=run load; run prog\0" \ | |
| "prog=prot off " __stringify(CONFIG_SYS_FLASH_BASE) \ | |
| " " __stringify(CONFIG_SYS_UBOOT_END) ";" \ | |
| "era " __stringify(CONFIG_SYS_FLASH_BASE) " " \ | |
| __stringify(CONFIG_SYS_UBOOT_END) ";" \ | |
| "cp.b ${loadaddr} " __stringify(CONFIG_SYS_FLASH_BASE) \ | |
| " ${filesize}; save\0" \ | |
| "" | |
| #endif | |
| /* ATA configuration */ | |
| #define CONFIG_ISO_PARTITION | |
| #define CONFIG_DOS_PARTITION | |
| #define CONFIG_IDE_RESET 1 | |
| #define CONFIG_IDE_PREINIT 1 | |
| #define CONFIG_ATAPI | |
| #undef CONFIG_LBA48 | |
| #define CONFIG_SYS_IDE_MAXBUS 1 | |
| #define CONFIG_SYS_IDE_MAXDEVICE 2 | |
| #define CONFIG_SYS_ATA_BASE_ADDR 0x90000000 | |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0 | |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ | |
| #define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ | |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ | |
| #define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ | |
| /* Realtime clock */ | |
| #define CONFIG_MCFRTC | |
| #undef RTC_DEBUG | |
| #define CONFIG_SYS_RTC_OSCILLATOR (32 * CONFIG_SYS_HZ) | |
| /* Timer */ | |
| #define CONFIG_MCFTMR | |
| #undef CONFIG_MCFPIT | |
| /* I2c */ | |
| #define CONFIG_SYS_I2C | |
| #define CONFIG_SYS_I2C_FSL | |
| #define CONFIG_SYS_FSL_I2C_SPEED 80000 | |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F | |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 | |
| #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR | |
| /* DSPI and Serial Flash */ | |
| #define CONFIG_CF_SPI | |
| #define CONFIG_CF_DSPI | |
| #define CONFIG_HARD_SPI | |
| #define CONFIG_SYS_SBFHDR_SIZE 0x13 | |
| #ifdef CONFIG_CMD_SPI | |
| # define CONFIG_SPI_FLASH | |
| # define CONFIG_SPI_FLASH_STMICRO | |
| # define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \ | |
| DSPI_CTAR_PCSSCK_1CLK | \ | |
| DSPI_CTAR_PASC(0) | \ | |
| DSPI_CTAR_PDT(0) | \ | |
| DSPI_CTAR_CSSCK(0) | \ | |
| DSPI_CTAR_ASC(0) | \ | |
| DSPI_CTAR_DT(1)) | |
| #endif | |
| /* PCI */ | |
| #ifdef CONFIG_CMD_PCI | |
| #define CONFIG_PCI 1 | |
| #define CONFIG_PCI_PNP 1 | |
| #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 | |
| #define CONFIG_SYS_PCI_CACHE_LINE_SIZE 4 | |
| #define CONFIG_SYS_PCI_MEM_BUS 0xA0000000 | |
| #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS | |
| #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 | |
| #define CONFIG_SYS_PCI_IO_BUS 0xB1000000 | |
| #define CONFIG_SYS_PCI_IO_PHYS CONFIG_SYS_PCI_IO_BUS | |
| #define CONFIG_SYS_PCI_IO_SIZE 0x01000000 | |
| #define CONFIG_SYS_PCI_CFG_BUS 0xB0000000 | |
| #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS | |
| #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000 | |
| #endif | |
| /* FPGA - Spartan 2 */ | |
| /* experiment | |
| #define CONFIG_FPGA | |
| #define CONFIG_FPGA_COUNT 1 | |
| #define CONFIG_SYS_FPGA_PROG_FEEDBACK | |
| #define CONFIG_SYS_FPGA_CHECK_CTRLC | |
| */ | |
| /* Input, PCI, Flexbus, and VCO */ | |
| #define CONFIG_EXTRA_CLOCK | |
| #define CONFIG_PRAM 2048 /* 2048 KB */ | |
| #define CONFIG_SYS_PROMPT "-> " | |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ | |
| #if defined(CONFIG_CMD_KGDB) | |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ | |
| #else | |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ | |
| #endif | |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ | |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ | |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ | |
| #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) | |
| #define CONFIG_SYS_MBAR 0xFC000000 | |
| /* | |
| * Low Level Configuration Settings | |
| * (address mappings, register initial values, etc.) | |
| * You should know what you are doing if you make changes here. | |
| */ | |
| /*----------------------------------------------------------------------- | |
| * Definitions for initial stack pointer and data area (in DPRAM) | |
| */ | |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 | |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */ | |
| #define CONFIG_SYS_INIT_RAM_CTRL 0x221 | |
| #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 32) | |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET | |
| #define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) | |
| /*----------------------------------------------------------------------- | |
| * Start addresses for the final memory configuration | |
| * (Set up by the startup code) | |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 | |
| */ | |
| #define CONFIG_SYS_SDRAM_BASE 0x40000000 | |
| #define CONFIG_SYS_SDRAM_BASE1 0x48000000 | |
| #define CONFIG_SYS_SDRAM_SIZE 256 /* SDRAM size in MB */ | |
| #define CONFIG_SYS_SDRAM_CFG1 0x65311610 | |
| #define CONFIG_SYS_SDRAM_CFG2 0x59670000 | |
| #define CONFIG_SYS_SDRAM_CTRL 0xEA0B2000 | |
| #define CONFIG_SYS_SDRAM_EMOD 0x40010000 | |
| #define CONFIG_SYS_SDRAM_MODE 0x00010033 | |
| #define CONFIG_SYS_SDRAM_DRV_STRENGTH 0xAA | |
| #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 | |
| #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) | |
| #ifdef CONFIG_CF_SBF | |
| # define CONFIG_SERIAL_BOOT | |
| # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) | |
| #else | |
| # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) | |
| #endif | |
| #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 | |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ | |
| /* Reserve 256 kB for malloc() */ | |
| #define CONFIG_SYS_MALLOC_LEN (256 << 10) | |
| /* | |
| * For booting Linux, the board info and command line data | |
| * have to be in the first 8 MB of memory, since this is | |
| * the maximum mapped by the Linux kernel during initialization ?? | |
| */ | |
| /* Initial Memory map for Linux */ | |
| #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) | |
| /* | |
| * Configuration for environment | |
| * Environment is not embedded in u-boot. First time runing may have env | |
| * crc error warning if there is no correct environment on the flash. | |
| */ | |
| #ifdef CONFIG_CF_SBF | |
| # define CONFIG_ENV_IS_IN_SPI_FLASH | |
| # define CONFIG_ENV_SPI_CS 1 | |
| #else | |
| # define CONFIG_ENV_IS_IN_FLASH 1 | |
| #endif | |
| #undef CONFIG_ENV_OVERWRITE | |
| /*----------------------------------------------------------------------- | |
| * FLASH organization | |
| */ | |
| #ifdef CONFIG_SYS_STMICRO_BOOT | |
| # define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE | |
| # define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS1_BASE | |
| # define CONFIG_ENV_OFFSET 0x30000 | |
| # define CONFIG_ENV_SIZE 0x2000 | |
| # define CONFIG_ENV_SECT_SIZE 0x10000 | |
| #endif | |
| #ifdef CONFIG_SYS_ATMEL_BOOT | |
| # define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE | |
| # define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS0_BASE | |
| # define CONFIG_SYS_FLASH1_BASE CONFIG_SYS_CS1_BASE | |
| # define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000) | |
| # define CONFIG_ENV_SIZE 0x2000 | |
| # define CONFIG_ENV_SECT_SIZE 0x10000 | |
| #endif | |
| #ifdef CONFIG_SYS_INTEL_BOOT | |
| # define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE | |
| # define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS0_BASE | |
| # define CONFIG_SYS_FLASH1_BASE CONFIG_SYS_CS1_BASE | |
| # define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000) | |
| # define CONFIG_ENV_SIZE 0x2000 | |
| # define CONFIG_ENV_SECT_SIZE 0x20000 | |
| #endif | |
| #define CONFIG_SYS_FLASH_CFI | |
| #ifdef CONFIG_SYS_FLASH_CFI | |
| # define CONFIG_FLASH_CFI_DRIVER 1 | |
| # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 | |
| # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */ | |
| # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT | |
| # define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ | |
| # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ | |
| # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ | |
| # define CONFIG_SYS_FLASH_CHECKSUM | |
| # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE } | |
| # define CONFIG_FLASH_CFI_LEGACY | |
| #ifdef CONFIG_FLASH_CFI_LEGACY | |
| # define CONFIG_SYS_ATMEL_REGION 4 | |
| # define CONFIG_SYS_ATMEL_TOTALSECT 11 | |
| # define CONFIG_SYS_ATMEL_SECT {1, 2, 1, 7} | |
| # define CONFIG_SYS_ATMEL_SECTSZ {0x4000, 0x2000, 0x8000, 0x10000} | |
| #endif | |
| #endif | |
| /* | |
| * This is setting for JFFS2 support in u-boot. | |
| * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. | |
| */ | |
| #ifdef CONFIG_CMD_JFFS2 | |
| #ifdef CF_STMICRO_BOOT | |
| # define CONFIG_JFFS2_DEV "nor1" | |
| # define CONFIG_JFFS2_PART_SIZE 0x01000000 | |
| # define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH2_BASE + 0x500000) | |
| #endif | |
| #ifdef CONFIG_SYS_ATMEL_BOOT | |
| # define CONFIG_JFFS2_DEV "nor1" | |
| # define CONFIG_JFFS2_PART_SIZE 0x01000000 | |
| # define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH1_BASE + 0x500000) | |
| #endif | |
| #ifdef CONFIG_SYS_INTEL_BOOT | |
| # define CONFIG_JFFS2_DEV "nor0" | |
| # define CONFIG_JFFS2_PART_SIZE (0x01000000 - 0x500000) | |
| # define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH0_BASE + 0x500000) | |
| #endif | |
| #endif | |
| /*----------------------------------------------------------------------- | |
| * Cache Configuration | |
| */ | |
| #define CONFIG_SYS_CACHELINE_SIZE 16 | |
| #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ | |
| CONFIG_SYS_INIT_RAM_SIZE - 8) | |
| #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ | |
| CONFIG_SYS_INIT_RAM_SIZE - 4) | |
| #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) | |
| #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) | |
| #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ | |
| CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ | |
| CF_ACR_EN | CF_ACR_SM_ALL) | |
| #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ | |
| CF_CACR_ICINVA | CF_CACR_EUSP) | |
| #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ | |
| CF_CACR_DEC | CF_CACR_DDCM_P | \ | |
| CF_CACR_DCINVA) & ~CF_CACR_ICINVA) | |
| /*----------------------------------------------------------------------- | |
| * Memory bank definitions | |
| */ | |
| /* | |
| * CS0 - NOR Flash 1, 2, 4, or 8MB | |
| * CS1 - CompactFlash and registers | |
| * CS2 - CPLD | |
| * CS3 - FPGA | |
| * CS4 - Available | |
| * CS5 - Available | |
| */ | |
| #if defined(CONFIG_SYS_ATMEL_BOOT) || defined(CONFIG_SYS_STMICRO_BOOT) | |
| /* Atmel Flash */ | |
| #define CONFIG_SYS_CS0_BASE 0x04000000 | |
| #define CONFIG_SYS_CS0_MASK 0x00070001 | |
| #define CONFIG_SYS_CS0_CTRL 0x00001140 | |
| /* Intel Flash */ | |
| #define CONFIG_SYS_CS1_BASE 0x00000000 | |
| #define CONFIG_SYS_CS1_MASK 0x01FF0001 | |
| #define CONFIG_SYS_CS1_CTRL 0x00000D60 | |
| #define CONFIG_SYS_ATMEL_BASE CONFIG_SYS_CS0_BASE | |
| #else | |
| /* Intel Flash */ | |
| #define CONFIG_SYS_CS0_BASE 0x00000000 | |
| #define CONFIG_SYS_CS0_MASK 0x01FF0001 | |
| #define CONFIG_SYS_CS0_CTRL 0x00000D60 | |
| /* Atmel Flash */ | |
| #define CONFIG_SYS_CS1_BASE 0x04000000 | |
| #define CONFIG_SYS_CS1_MASK 0x00070001 | |
| #define CONFIG_SYS_CS1_CTRL 0x00001140 | |
| #define CONFIG_SYS_ATMEL_BASE CONFIG_SYS_CS1_BASE | |
| #endif | |
| /* CPLD */ | |
| #define CONFIG_SYS_CS2_BASE 0x08000000 | |
| #define CONFIG_SYS_CS2_MASK 0x00070001 | |
| #define CONFIG_SYS_CS2_CTRL 0x003f1140 | |
| /* FPGA */ | |
| #define CONFIG_SYS_CS3_BASE 0x09000000 | |
| #define CONFIG_SYS_CS3_MASK 0x00070001 | |
| #define CONFIG_SYS_CS3_CTRL 0x00000020 | |
| #endif /* _M54455EVB_H */ |