include/configs/T4240QDS.h - u-boot - Git at Google


            
            /*

            
             * Copyright 2011-2012 Freescale Semiconductor, Inc.

            
             *

            
             * SPDX-License-Identifier:	GPL-2.0+

            
             */


            /*

            
             * T4240 QDS board configuration file

            
             */

            
            #ifndef __CONFIG_H

            
            #define __CONFIG_H


            #define CONFIG_T4240QDS

            
            #define CONFIG_PHYS_64BIT


            #define CONFIG_FSL_SATA_V2

            
            #define CONFIG_PCIE4


            #define CONFIG_ICS307_REFCLK_HZ		25000000  /* ICS307 ref clk freq */


            #ifdef CONFIG_RAMBOOT_PBL

            
            #define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE

            
            #define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc

            
            #define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg

            
            #define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg

            
            #endif


            #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE

            
            /* Set 1M boot space */

            
            #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)

            
            #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \

            
            		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)

            
            #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc

            
            #define CONFIG_SYS_NO_FLASH

            
            #endif


            #define CONFIG_SRIO_PCIE_BOOT_MASTER

            
            #define CONFIG_DDR_ECC


            #include "t4qds.h"


            #ifdef CONFIG_SYS_NO_FLASH

            
            #if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)

            
            #define CONFIG_ENV_IS_NOWHERE

            
            #endif

            
            #else

            
            #define CONFIG_FLASH_CFI_DRIVER

            
            #define CONFIG_SYS_FLASH_CFI

            
            #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE

            
            #endif


            #if defined(CONFIG_SPIFLASH)

            
            #define CONFIG_SYS_EXTRA_ENV_RELOC

            
            #define CONFIG_ENV_IS_IN_SPI_FLASH

            
            #define CONFIG_ENV_SPI_BUS              0

            
            #define CONFIG_ENV_SPI_CS               0

            
            #define CONFIG_ENV_SPI_MAX_HZ           10000000

            
            #define CONFIG_ENV_SPI_MODE             0

            
            #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */

            
            #define CONFIG_ENV_OFFSET               0x100000        /* 1MB */

            
            #define CONFIG_ENV_SECT_SIZE            0x10000

            
            #elif defined(CONFIG_SDCARD)

            
            #define CONFIG_SYS_EXTRA_ENV_RELOC

            
            #define CONFIG_ENV_IS_IN_MMC

            
            #define CONFIG_SYS_MMC_ENV_DEV          0

            
            #define CONFIG_ENV_SIZE			0x2000

            
            #define CONFIG_ENV_OFFSET		(512 * 1097)

            
            #elif defined(CONFIG_NAND)

            
            #define CONFIG_SYS_EXTRA_ENV_RELOC

            
            #define CONFIG_ENV_IS_IN_NAND

            
            #define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE

            
            #define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)

            
            #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)

            
            #define CONFIG_ENV_IS_IN_REMOTE

            
            #define CONFIG_ENV_ADDR		0xffe20000

            
            #define CONFIG_ENV_SIZE		0x2000

            
            #elif defined(CONFIG_ENV_IS_NOWHERE)

            
            #define CONFIG_ENV_SIZE		0x2000

            
            #else

            
            #define CONFIG_ENV_IS_IN_FLASH

            
            #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)

            
            #define CONFIG_ENV_SIZE		0x2000

            
            #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */

            
            #endif


            #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk()

            
            #define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk()


            #ifndef __ASSEMBLY__

            
            unsigned long get_board_sys_clk(void);

            
            unsigned long get_board_ddr_clk(void);

            
            #endif


            /* EEPROM */

            
            #define CONFIG_ID_EEPROM

            
            #define CONFIG_SYS_I2C_EEPROM_NXID

            
            #define CONFIG_SYS_EEPROM_BUS_NUM	0

            
            #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57

            
            #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1


            /*

            
             * DDR Setup

            
             */

            
            #define CONFIG_SYS_SPD_BUS_NUM	0

            
            #define SPD_EEPROM_ADDRESS1	0x51

            
            #define SPD_EEPROM_ADDRESS2	0x52

            
            #define SPD_EEPROM_ADDRESS3	0x53

            
            #define SPD_EEPROM_ADDRESS4	0x54

            
            #define SPD_EEPROM_ADDRESS5	0x55

            
            #define SPD_EEPROM_ADDRESS6	0x56

            
            #define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1	/* for p3041/p5010 */

            
            #define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */


            /*

            
             * IFC Definitions

            
             */

            
            #define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)

            
            #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \

            
            				+ 0x8000000) | \

            
            				CSPR_PORT_SIZE_16 | \

            
            				CSPR_MSEL_NOR | \

            
            				CSPR_V)

            
            #define CONFIG_SYS_NOR1_CSPR_EXT	(0xf)

            
            #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \

            
            				CSPR_PORT_SIZE_16 | \

            
            				CSPR_MSEL_NOR | \

            
            				CSPR_V)

            
            #define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)

            
            /* NOR Flash Timing Params */

            
            #define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80


            #define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \

            
            				FTIM0_NOR_TEADC(0x5) | \

            
            				FTIM0_NOR_TEAHC(0x5))

            
            #define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \

            
            				FTIM1_NOR_TRAD_NOR(0x1A) |\

            
            				FTIM1_NOR_TSEQRAD_NOR(0x13))

            
            #define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \

            
            				FTIM2_NOR_TCH(0x4) | \

            
            				FTIM2_NOR_TWPH(0x0E) | \

            
            				FTIM2_NOR_TWP(0x1c))

            
            #define CONFIG_SYS_NOR_FTIM3	0x0


            #define CONFIG_SYS_FLASH_QUIET_TEST

            
            #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */


            #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */

            
            #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */

            
            #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */

            
            #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */


            #define CONFIG_SYS_FLASH_EMPTY_INFO

            
            #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS \

            
            					+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}


            #define CONFIG_FSL_QIXIS	/* use common QIXIS code */

            
            #define QIXIS_BASE			0xffdf0000

            
            #define QIXIS_LBMAP_SWITCH		6

            
            #define QIXIS_LBMAP_MASK		0x0f

            
            #define QIXIS_LBMAP_SHIFT		0

            
            #define QIXIS_LBMAP_DFLTBANK		0x00

            
            #define QIXIS_LBMAP_ALTBANK		0x04

            
            #define QIXIS_RST_CTL_RESET		0x83

            
            #define QIXIS_RST_FORCE_MEM		0x1

            
            #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20

            
            #define QIXIS_RCFG_CTL_RECONFIG_START	0x21

            
            #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08

            
            #define QIXIS_BASE_PHYS		(0xf00000000ull | QIXIS_BASE)


            #define CONFIG_SYS_CSPR3_EXT	(0xf)

            
            #define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \

            
            				| CSPR_PORT_SIZE_8 \

            
            				| CSPR_MSEL_GPCM \

            
            				| CSPR_V)

            
            #define CONFIG_SYS_AMASK3	IFC_AMASK(4*1024)

            
            #define CONFIG_SYS_CSOR3	0x0

            
            /* QIXIS Timing parameters for IFC CS3 */

            
            #define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \

            
            					FTIM0_GPCM_TEADC(0x0e) | \

            
            					FTIM0_GPCM_TEAHC(0x0e))

            
            #define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \

            
            					FTIM1_GPCM_TRAD(0x3f))

            
            #define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \

            
            					FTIM2_GPCM_TCH(0x0) | \

            
            					FTIM2_GPCM_TWP(0x1f))

            
            #define CONFIG_SYS_CS3_FTIM3		0x0


            /* NAND Flash on IFC */

            
            #define CONFIG_NAND_FSL_IFC

            
            #define CONFIG_SYS_NAND_BASE		0xff800000

            
            #define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)


            #define CONFIG_SYS_NAND_CSPR_EXT	(0xf)

            
            #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \

            
            				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \

            
            				| CSPR_MSEL_NAND	/* MSEL = NAND */ \

            
            				| CSPR_V)

            
            #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)


            #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \

            
            				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \

            
            				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \

            
            				| CSOR_NAND_RAL_3	/* RAL = 2Byes */ \

            
            				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \

            
            				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \

            
            				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/


            #define CONFIG_SYS_NAND_ONFI_DETECTION


            /* ONFI NAND Flash mode0 Timing Params */

            
            #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \

            
            					FTIM0_NAND_TWP(0x18)   | \

            
            					FTIM0_NAND_TWCHT(0x07) | \

            
            					FTIM0_NAND_TWH(0x0a))

            
            #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \

            
            					FTIM1_NAND_TWBE(0x39)  | \

            
            					FTIM1_NAND_TRR(0x0e)   | \

            
            					FTIM1_NAND_TRP(0x18))

            
            #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \

            
            					FTIM2_NAND_TREH(0x0a) | \

            
            					FTIM2_NAND_TWHRE(0x1e))

            
            #define CONFIG_SYS_NAND_FTIM3		0x0


            #define CONFIG_SYS_NAND_DDR_LAW		11


            #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }

            
            #define CONFIG_SYS_MAX_NAND_DEVICE	1

            
            #define CONFIG_MTD_NAND_VERIFY_WRITE

            
            #define CONFIG_CMD_NAND


            #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)

            
            #define CONFIG_SYS_NAND_MAX_OOBFREE	2

            
            #define CONFIG_SYS_NAND_MAX_ECCPOS	256


            #if defined(CONFIG_NAND)

            
            #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT

            
            #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR

            
            #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK

            
            #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR

            
            #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0

            
            #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1

            
            #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2

            
            #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3

            
            #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT

            
            #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR

            
            #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK

            
            #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR

            
            #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0

            
            #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1

            
            #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2

            
            #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3

            
            #else

            
            #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT

            
            #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR

            
            #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK

            
            #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR

            
            #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0

            
            #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1

            
            #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2

            
            #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3

            
            #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT

            
            #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR

            
            #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK

            
            #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR

            
            #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0

            
            #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1

            
            #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2

            
            #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3

            
            #endif

            
            #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT

            
            #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR

            
            #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK

            
            #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR

            
            #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0

            
            #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1

            
            #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2

            
            #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3


            #if defined(CONFIG_RAMBOOT_PBL)

            
            #define CONFIG_SYS_RAMBOOT

            
            #endif


            /* I2C */

            
            #define CONFIG_SYS_FSL_I2C_SPEED	100000	/* I2C speed */

            
            #define CONFIG_SYS_FSL_I2C2_SPEED	100000	/* I2C2 speed */

            
            #define I2C_MUX_PCA_ADDR_PRI		0x77 /* I2C bus multiplexer,primary */

            
            #define I2C_MUX_PCA_ADDR_SEC		0x76 /* I2C bus multiplexer,secondary */


            #define I2C_MUX_CH_DEFAULT	0x8

            
            #define I2C_MUX_CH_VOL_MONITOR	0xa

            
            #define I2C_MUX_CH_VSC3316_FS	0xc

            
            #define I2C_MUX_CH_VSC3316_BS	0xd


            /* Voltage monitor on channel 2*/

            
            #define I2C_VOL_MONITOR_ADDR		0x40

            
            #define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2

            
            #define I2C_VOL_MONITOR_BUS_V_OVF	0x1

            
            #define I2C_VOL_MONITOR_BUS_V_SHIFT	3


            /* VSC Crossbar switches */

            
            #define CONFIG_VSC_CROSSBAR

            
            #define VSC3316_FSM_TX_ADDR	0x70

            
            #define VSC3316_FSM_RX_ADDR	0x71


            /*

            
             * RapidIO

            
             */


            /*

            
             * for slave u-boot IMAGE instored in master memory space,

            
             * PHYS must be aligned based on the SIZE

            
             */

            
            #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull

            
            #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull

            
            #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000	/* 512K */

            
            #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull

            
            /*

            
             * for slave UCODE and ENV instored in master memory space,

            
             * PHYS must be aligned based on the SIZE

            
             */

            
            #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull

            
            #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull

            
            #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000	/* 256K */


            /* slave core release by master*/

            
            #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4

            
            #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */


            /*

            
             * SRIO_PCIE_BOOT - SLAVE

            
             */

            
            #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE

            
            #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000

            
            #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \

            
            		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)

            
            #endif

            
            /*

            
             * eSPI - Enhanced SPI

            
             */

            
            #define CONFIG_FSL_ESPI

            
            #define CONFIG_SPI_FLASH

            
            #define CONFIG_SPI_FLASH_SST

            
            #define CONFIG_CMD_SF

            
            #define CONFIG_SF_DEFAULT_SPEED         10000000

            
            #define CONFIG_SF_DEFAULT_MODE          0


            /* Qman/Bman */

            
            #ifndef CONFIG_NOBQFMAN

            
            #define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */

            
            #define CONFIG_SYS_BMAN_NUM_PORTALS	50

            
            #define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000

            
            #define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull

            
            #define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000

            
            #define CONFIG_SYS_QMAN_NUM_PORTALS	50

            
            #define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000

            
            #define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull

            
            #define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000


            #define CONFIG_SYS_DPAA_FMAN

            
            #define CONFIG_SYS_DPAA_PME

            
            #define CONFIG_SYS_PMAN

            
            #define CONFIG_SYS_DPAA_DCE

            
            #define CONFIG_SYS_DPAA_RMAN

            
            #define CONFIG_SYS_INTERLAKEN


            /* Default address of microcode for the Linux Fman driver */

            
            #if defined(CONFIG_SPIFLASH)

            
            /*

            
             * env is stored at 0x100000, sector size is 0x10000, ucode is stored after

            
             * env, so we got 0x110000.

            
             */

            
            #define CONFIG_SYS_QE_FW_IN_SPIFLASH

            
            #define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000

            
            #elif defined(CONFIG_SDCARD)

            
            /*

            
             * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is

            
             * about 545KB (1089 blocks), Env is stored after the image, and the env size is

            
             * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.

            
             */

            
            #define CONFIG_SYS_QE_FMAN_FW_IN_MMC

            
            #define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)

            
            #elif defined(CONFIG_NAND)

            
            #define CONFIG_SYS_QE_FMAN_FW_IN_NAND

            
            #define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)

            
            #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)

            
            /*

            
             * Slave has no ucode locally, it can fetch this from remote. When implementing

            
             * in two corenet boards, slave's ucode could be stored in master's memory

            
             * space, the address can be mapped from slave TLB->slave LAW->

            
             * slave SRIO or PCIE outbound window->master inbound window->

            
             * master LAW->the ucode address in master's memory space.

            
             */

            
            #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE

            
            #define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000

            
            #else

            
            #define CONFIG_SYS_QE_FMAN_FW_IN_NOR

            
            #define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF40000

            
            #endif

            
            #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000

            
            #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

            
            #endif /* CONFIG_NOBQFMAN */


            #ifdef CONFIG_SYS_DPAA_FMAN

            
            #define CONFIG_FMAN_ENET

            
            #define CONFIG_PHYLIB_10G

            
            #define CONFIG_PHY_VITESSE

            
            #define CONFIG_PHY_TERANETICS

            
            #define SGMII_CARD_PORT1_PHY_ADDR 0x1C

            
            #define SGMII_CARD_PORT2_PHY_ADDR 0x1D

            
            #define SGMII_CARD_PORT3_PHY_ADDR 0x1E

            
            #define SGMII_CARD_PORT4_PHY_ADDR 0x1F

            
            #define FM1_10GEC1_PHY_ADDR	0x0

            
            #define FM1_10GEC2_PHY_ADDR	0x1

            
            #define FM2_10GEC1_PHY_ADDR	0x2

            
            #define FM2_10GEC2_PHY_ADDR	0x3

            
            #endif


            /* SATA */

            
            #ifdef CONFIG_FSL_SATA_V2

            
            #define CONFIG_LIBATA

            
            #define CONFIG_FSL_SATA


            #define CONFIG_SYS_SATA_MAX_DEVICE	2

            
            #define CONFIG_SATA1

            
            #define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR

            
            #define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA

            
            #define CONFIG_SATA2

            
            #define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR

            
            #define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA


            #define CONFIG_LBA48

            
            #define CONFIG_CMD_SATA

            
            #define CONFIG_DOS_PARTITION

            
            #define CONFIG_CMD_EXT2

            
            #endif


            #ifdef CONFIG_FMAN_ENET

            
            #define CONFIG_MII		/* MII PHY management */

            
            #define CONFIG_ETHPRIME		"FM1@DTSEC1"

            
            #define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */

            
            #endif


            /*

            
            * USB

            
            */

            
            #define CONFIG_CMD_USB

            
            #define CONFIG_USB_STORAGE

            
            #define CONFIG_USB_EHCI

            
            #define CONFIG_USB_EHCI_FSL

            
            #define CONFIG_EHCI_HCD_INIT_AFTER_RESET

            
            #define CONFIG_CMD_EXT2

            
            #define CONFIG_HAS_FSL_DR_USB


            #define CONFIG_MMC


            #ifdef CONFIG_MMC

            
            #define CONFIG_FSL_ESDHC

            
            #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR

            
            #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT

            
            #define CONFIG_CMD_MMC

            
            #define CONFIG_GENERIC_MMC

            
            #define CONFIG_CMD_EXT2

            
            #define CONFIG_CMD_FAT

            
            #define CONFIG_DOS_PARTITION

            
            #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33

            
            #endif


            #define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */


            #define __USB_PHY_TYPE	utmi


            /*

            
             * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be

            
             * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way

            
             * interleaving. It can be cacheline, page, bank, superbank.

            
             * See doc/README.fsl-ddr for details.

            
             */

            
            #ifdef CONFIG_PPC_T4240

            
            #define CTRL_INTLV_PREFERED 3way_4KB

            
            #else

            
            #define CTRL_INTLV_PREFERED cacheline

            
            #endif


            #define	CONFIG_EXTRA_ENV_SETTINGS				\

            
            	"hwconfig=fsl_ddr:"					\

            
            	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\

            
            	"bank_intlv=auto;"					\

            
            	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\

            
            	"netdev=eth0\0"						\

            
            	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\

            
            	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"		\

            
            	"tftpflash=tftpboot $loadaddr $uboot && "		\

            
            	"protect off $ubootaddr +$filesize && "			\

            
            	"erase $ubootaddr +$filesize && "			\

            
            	"cp.b $loadaddr $ubootaddr $filesize && "		\

            
            	"protect on $ubootaddr +$filesize && "			\

            
            	"cmp.b $loadaddr $ubootaddr $filesize\0"		\

            
            	"consoledev=ttyS0\0"					\

            
            	"ramdiskaddr=2000000\0"					\

            
            	"ramdiskfile=t4240qds/ramdisk.uboot\0"			\

            
            	"fdtaddr=c00000\0"					\

            
            	"fdtfile=t4240qds/t4240qds.dtb\0"				\

            
            	"bdev=sda3\0"						\

            
            	"c=ffe\0"


            #define CONFIG_HVBOOT				\

            
            	"setenv bootargs config-addr=0x60000000; "	\

            
            	"bootm 0x01000000 - 0x00f00000"


            #define CONFIG_ALU				\

            
            	"setenv bootargs root=/dev/$bdev rw "		\

            
            	"console=$consoledev,$baudrate $othbootargs;"	\

            
            	"cpu 1 release 0x01000000 - - -;"		\

            
            	"cpu 2 release 0x01000000 - - -;"		\

            
            	"cpu 3 release 0x01000000 - - -;"		\

            
            	"cpu 4 release 0x01000000 - - -;"		\

            
            	"cpu 5 release 0x01000000 - - -;"		\

            
            	"cpu 6 release 0x01000000 - - -;"		\

            
            	"cpu 7 release 0x01000000 - - -;"		\

            
            	"go 0x01000000"


            #define CONFIG_LINUX				\

            
            	"setenv bootargs root=/dev/ram rw "		\

            
            	"console=$consoledev,$baudrate $othbootargs;"	\

            
            	"setenv ramdiskaddr 0x02000000;"		\

            
            	"setenv fdtaddr 0x00c00000;"			\

            
            	"setenv loadaddr 0x1000000;"			\

            
            	"bootm $loadaddr $ramdiskaddr $fdtaddr"


            #define CONFIG_HDBOOT					\

            
            	"setenv bootargs root=/dev/$bdev rw "		\

            
            	"console=$consoledev,$baudrate $othbootargs;"	\

            
            	"tftp $loadaddr $bootfile;"			\

            
            	"tftp $fdtaddr $fdtfile;"			\

            
            	"bootm $loadaddr - $fdtaddr"


            #define CONFIG_NFSBOOTCOMMAND			\

            
            	"setenv bootargs root=/dev/nfs rw "	\

            
            	"nfsroot=$serverip:$rootpath "		\

            
            	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \

            
            	"console=$consoledev,$baudrate $othbootargs;"	\

            
            	"tftp $loadaddr $bootfile;"		\

            
            	"tftp $fdtaddr $fdtfile;"		\

            
            	"bootm $loadaddr - $fdtaddr"


            #define CONFIG_RAMBOOTCOMMAND				\

            
            	"setenv bootargs root=/dev/ram rw "		\

            
            	"console=$consoledev,$baudrate $othbootargs;"	\

            
            	"tftp $ramdiskaddr $ramdiskfile;"		\

            
            	"tftp $loadaddr $bootfile;"			\

            
            	"tftp $fdtaddr $fdtfile;"			\

            
            	"bootm $loadaddr $ramdiskaddr $fdtaddr"


            #define CONFIG_BOOTCOMMAND		CONFIG_LINUX


            #include <asm/fsl_secure_boot.h>


            #endif	/* __CONFIG_H */
	/*
	* Copyright 2011-2012 Freescale Semiconductor, Inc.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/*
	* T4240 QDS board configuration file
	*/
	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_T4240QDS
	#define CONFIG_PHYS_64BIT

	#define CONFIG_FSL_SATA_V2
	#define CONFIG_PCIE4

	#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */

	#ifdef CONFIG_RAMBOOT_PBL
	#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg
	#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg
	#endif

	#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
	/* Set 1M boot space */
	#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
	#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
	(0x300000000ull \| CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	#define CONFIG_SYS_NO_FLASH
	#endif

	#define CONFIG_SRIO_PCIE_BOOT_MASTER
	#define CONFIG_DDR_ECC

	#include "t4qds.h"

	#ifdef CONFIG_SYS_NO_FLASH
	#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
	#define CONFIG_ENV_IS_NOWHERE
	#endif
	#else
	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
	#endif

	#if defined(CONFIG_SPIFLASH)
	#define CONFIG_SYS_EXTRA_ENV_RELOC
	#define CONFIG_ENV_IS_IN_SPI_FLASH
	#define CONFIG_ENV_SPI_BUS 0
	#define CONFIG_ENV_SPI_CS 0
	#define CONFIG_ENV_SPI_MAX_HZ 10000000
	#define CONFIG_ENV_SPI_MODE 0
	#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
	#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
	#define CONFIG_ENV_SECT_SIZE 0x10000
	#elif defined(CONFIG_SDCARD)
	#define CONFIG_SYS_EXTRA_ENV_RELOC
	#define CONFIG_ENV_IS_IN_MMC
	#define CONFIG_SYS_MMC_ENV_DEV 0
	#define CONFIG_ENV_SIZE 0x2000
	#define CONFIG_ENV_OFFSET (512 * 1097)
	#elif defined(CONFIG_NAND)
	#define CONFIG_SYS_EXTRA_ENV_RELOC
	#define CONFIG_ENV_IS_IN_NAND
	#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
	#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
	#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
	#define CONFIG_ENV_IS_IN_REMOTE
	#define CONFIG_ENV_ADDR 0xffe20000
	#define CONFIG_ENV_SIZE 0x2000
	#elif defined(CONFIG_ENV_IS_NOWHERE)
	#define CONFIG_ENV_SIZE 0x2000
	#else
	#define CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE 0x2000
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
	#endif

	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
	#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()

	#ifndef __ASSEMBLY__
	unsigned long get_board_sys_clk(void);
	unsigned long get_board_ddr_clk(void);
	#endif

	/* EEPROM */
	#define CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_SYS_EEPROM_BUS_NUM 0
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1

	/*
	* DDR Setup
	*/
	#define CONFIG_SYS_SPD_BUS_NUM 0
	#define SPD_EEPROM_ADDRESS1 0x51
	#define SPD_EEPROM_ADDRESS2 0x52
	#define SPD_EEPROM_ADDRESS3 0x53
	#define SPD_EEPROM_ADDRESS4 0x54
	#define SPD_EEPROM_ADDRESS5 0x55
	#define SPD_EEPROM_ADDRESS6 0x56
	#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */
	#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */

	/*
	* IFC Definitions
	*/
	#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
	#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
	+ 0x8000000) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
	#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CONFIG_SYS_NOR_AMASK IFC_AMASK(12810241024)
	/* NOR Flash Timing Params */
	#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80

	#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) \| \
	FTIM0_NOR_TEADC(0x5) \| \
	FTIM0_NOR_TEAHC(0x5))
	#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) \| \
	FTIM1_NOR_TRAD_NOR(0x1A) \|\
	FTIM1_NOR_TSEQRAD_NOR(0x13))
	#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) \| \
	FTIM2_NOR_TCH(0x4) \| \
	FTIM2_NOR_TWPH(0x0E) \| \
	FTIM2_NOR_TWP(0x1c))
	#define CONFIG_SYS_NOR_FTIM3 0x0

	#define CONFIG_SYS_FLASH_QUIET_TEST
	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
	+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}

	#define CONFIG_FSL_QIXIS /* use common QIXIS code */
	#define QIXIS_BASE 0xffdf0000
	#define QIXIS_LBMAP_SWITCH 6
	#define QIXIS_LBMAP_MASK 0x0f
	#define QIXIS_LBMAP_SHIFT 0
	#define QIXIS_LBMAP_DFLTBANK 0x00
	#define QIXIS_LBMAP_ALTBANK 0x04
	#define QIXIS_RST_CTL_RESET 0x83
	#define QIXIS_RST_FORCE_MEM 0x1
	#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
	#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
	#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
	#define QIXIS_BASE_PHYS (0xf00000000ull \| QIXIS_BASE)

	#define CONFIG_SYS_CSPR3_EXT (0xf)
	#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 \
	\| CSPR_MSEL_GPCM \
	\| CSPR_V)
	#define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024)
	#define CONFIG_SYS_CSOR3 0x0
	/* QIXIS Timing parameters for IFC CS3 */
	#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) \| \
	FTIM0_GPCM_TEADC(0x0e) \| \
	FTIM0_GPCM_TEAHC(0x0e))
	#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) \| \
	FTIM1_GPCM_TRAD(0x3f))
	#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) \| \
	FTIM2_GPCM_TCH(0x0) \| \
	FTIM2_GPCM_TWP(0x1f))
	#define CONFIG_SYS_CS3_FTIM3 0x0

	/* NAND Flash on IFC */
	#define CONFIG_NAND_FSL_IFC
	#define CONFIG_SYS_NAND_BASE 0xff800000
	#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull \| CONFIG_SYS_NAND_BASE)

	#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
	#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
	\| CSPR_MSEL_NAND /* MSEL = NAND */ \
	\| CSPR_V)
	#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)

	#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	\| CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
	\| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
	\| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
	\| CSOR_NAND_PB(64)) /Pages Per Block = 64/

	#define CONFIG_SYS_NAND_ONFI_DETECTION

	/* ONFI NAND Flash mode0 Timing Params */
	#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) \| \
	FTIM0_NAND_TWP(0x18) \| \
	FTIM0_NAND_TWCHT(0x07) \| \
	FTIM0_NAND_TWH(0x0a))
	#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) \| \
	FTIM1_NAND_TWBE(0x39) \| \
	FTIM1_NAND_TRR(0x0e) \| \
	FTIM1_NAND_TRP(0x18))
	#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) \| \
	FTIM2_NAND_TREH(0x0a) \| \
	FTIM2_NAND_TWHRE(0x1e))
	#define CONFIG_SYS_NAND_FTIM3 0x0

	#define CONFIG_SYS_NAND_DDR_LAW 11

	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_MTD_NAND_VERIFY_WRITE
	#define CONFIG_CMD_NAND

	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
	#define CONFIG_SYS_NAND_MAX_OOBFREE 2
	#define CONFIG_SYS_NAND_MAX_ECCPOS 256

	#if defined(CONFIG_NAND)
	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
	#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR
	#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
	#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
	#else
	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
	#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
	#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
	#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
	#endif
	#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
	#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
	#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
	#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
	#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
	#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
	#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
	#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3

	#if defined(CONFIG_RAMBOOT_PBL)
	#define CONFIG_SYS_RAMBOOT
	#endif


	/* I2C */
	#define CONFIG_SYS_FSL_I2C_SPEED 100000 /* I2C speed */
	#define CONFIG_SYS_FSL_I2C2_SPEED 100000 /* I2C2 speed */
	#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
	#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */

	#define I2C_MUX_CH_DEFAULT 0x8
	#define I2C_MUX_CH_VOL_MONITOR 0xa
	#define I2C_MUX_CH_VSC3316_FS 0xc
	#define I2C_MUX_CH_VSC3316_BS 0xd

	/* Voltage monitor on channel 2*/
	#define I2C_VOL_MONITOR_ADDR 0x40
	#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
	#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
	#define I2C_VOL_MONITOR_BUS_V_SHIFT 3

	/* VSC Crossbar switches */
	#define CONFIG_VSC_CROSSBAR
	#define VSC3316_FSM_TX_ADDR 0x70
	#define VSC3316_FSM_RX_ADDR 0x71

	/*
	* RapidIO
	*/

	/*
	* for slave u-boot IMAGE instored in master memory space,
	* PHYS must be aligned based on the SIZE
	*/
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
	/*
	* for slave UCODE and ENV instored in master memory space,
	* PHYS must be aligned based on the SIZE
	*/
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */

	/* slave core release by master*/
	#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
	#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

	/*
	* SRIO_PCIE_BOOT - SLAVE
	*/
	#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
	#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
	#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
	(0x300000000ull \| CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
	#endif
	/*
	* eSPI - Enhanced SPI
	*/
	#define CONFIG_FSL_ESPI
	#define CONFIG_SPI_FLASH
	#define CONFIG_SPI_FLASH_SST
	#define CONFIG_CMD_SF
	#define CONFIG_SF_DEFAULT_SPEED 10000000
	#define CONFIG_SF_DEFAULT_MODE 0


	/* Qman/Bman */
	#ifndef CONFIG_NOBQFMAN
	#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
	#define CONFIG_SYS_BMAN_NUM_PORTALS 50
	#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
	#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
	#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
	#define CONFIG_SYS_QMAN_NUM_PORTALS 50
	#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
	#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
	#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000

	#define CONFIG_SYS_DPAA_FMAN
	#define CONFIG_SYS_DPAA_PME
	#define CONFIG_SYS_PMAN
	#define CONFIG_SYS_DPAA_DCE
	#define CONFIG_SYS_DPAA_RMAN
	#define CONFIG_SYS_INTERLAKEN

	/* Default address of microcode for the Linux Fman driver */
	#if defined(CONFIG_SPIFLASH)
	/*
	* env is stored at 0x100000, sector size is 0x10000, ucode is stored after
	* env, so we got 0x110000.
	*/
	#define CONFIG_SYS_QE_FW_IN_SPIFLASH
	#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000
	#elif defined(CONFIG_SDCARD)
	/*
	* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
	* about 545KB (1089 blocks), Env is stored after the image, and the env size is
	* 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
	*/
	#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
	#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130)
	#elif defined(CONFIG_NAND)
	#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
	#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
	#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
	/*
	* Slave has no ucode locally, it can fetch this from remote. When implementing
	* in two corenet boards, slave's ucode could be stored in master's memory
	* space, the address can be mapped from slave TLB->slave LAW->
	* slave SRIO or PCIE outbound window->master inbound window->
	* master LAW->the ucode address in master's memory space.
	*/
	#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
	#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000
	#else
	#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
	#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000
	#endif
	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
	#endif /* CONFIG_NOBQFMAN */

	#ifdef CONFIG_SYS_DPAA_FMAN
	#define CONFIG_FMAN_ENET
	#define CONFIG_PHYLIB_10G
	#define CONFIG_PHY_VITESSE
	#define CONFIG_PHY_TERANETICS
	#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
	#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
	#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
	#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
	#define FM1_10GEC1_PHY_ADDR 0x0
	#define FM1_10GEC2_PHY_ADDR 0x1
	#define FM2_10GEC1_PHY_ADDR 0x2
	#define FM2_10GEC2_PHY_ADDR 0x3
	#endif


	/* SATA */
	#ifdef CONFIG_FSL_SATA_V2
	#define CONFIG_LIBATA
	#define CONFIG_FSL_SATA

	#define CONFIG_SYS_SATA_MAX_DEVICE 2
	#define CONFIG_SATA1
	#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
	#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
	#define CONFIG_SATA2
	#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
	#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA

	#define CONFIG_LBA48
	#define CONFIG_CMD_SATA
	#define CONFIG_DOS_PARTITION
	#define CONFIG_CMD_EXT2
	#endif

	#ifdef CONFIG_FMAN_ENET
	#define CONFIG_MII /* MII PHY management */
	#define CONFIG_ETHPRIME "FM1@DTSEC1"
	#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
	#endif

	/*
	* USB
	*/
	#define CONFIG_CMD_USB
	#define CONFIG_USB_STORAGE
	#define CONFIG_USB_EHCI
	#define CONFIG_USB_EHCI_FSL
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	#define CONFIG_CMD_EXT2
	#define CONFIG_HAS_FSL_DR_USB

	#define CONFIG_MMC

	#ifdef CONFIG_MMC
	#define CONFIG_FSL_ESDHC
	#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
	#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
	#define CONFIG_CMD_MMC
	#define CONFIG_GENERIC_MMC
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_FAT
	#define CONFIG_DOS_PARTITION
	#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
	#endif

	#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */

	#define __USB_PHY_TYPE utmi

	/*
	* T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
	* 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
	* interleaving. It can be cacheline, page, bank, superbank.
	* See doc/README.fsl-ddr for details.
	*/
	#ifdef CONFIG_PPC_T4240
	#define CTRL_INTLV_PREFERED 3way_4KB
	#else
	#define CTRL_INTLV_PREFERED cacheline
	#endif

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:" \
	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
	"bank_intlv=auto;" \
	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
	"netdev=eth0\0" \
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
	"tftpflash=tftpboot $loadaddr $uboot && " \
	"protect off $ubootaddr +$filesize && " \
	"erase $ubootaddr +$filesize && " \
	"cp.b $loadaddr $ubootaddr $filesize && " \
	"protect on $ubootaddr +$filesize && " \
	"cmp.b $loadaddr $ubootaddr $filesize\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=2000000\0" \
	"ramdiskfile=t4240qds/ramdisk.uboot\0" \
	"fdtaddr=c00000\0" \
	"fdtfile=t4240qds/t4240qds.dtb\0" \
	"bdev=sda3\0" \
	"c=ffe\0"

	#define CONFIG_HVBOOT \
	"setenv bootargs config-addr=0x60000000; " \
	"bootm 0x01000000 - 0x00f00000"

	#define CONFIG_ALU \
	"setenv bootargs root=/dev/$bdev rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"cpu 1 release 0x01000000 - - -;" \
	"cpu 2 release 0x01000000 - - -;" \
	"cpu 3 release 0x01000000 - - -;" \
	"cpu 4 release 0x01000000 - - -;" \
	"cpu 5 release 0x01000000 - - -;" \
	"cpu 6 release 0x01000000 - - -;" \
	"cpu 7 release 0x01000000 - - -;" \
	"go 0x01000000"

	#define CONFIG_LINUX \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"setenv ramdiskaddr 0x02000000;" \
	"setenv fdtaddr 0x00c00000;" \
	"setenv loadaddr 0x1000000;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_HDBOOT \
	"setenv bootargs root=/dev/$bdev rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_BOOTCOMMAND CONFIG_LINUX

	#include <asm/fsl_secure_boot.h>

	#endif /* __CONFIG_H */