| /* | |
| * U-boot - cpu.c CPU specific functions | |
| * | |
| * Copyright (c) 2005-2008 Analog Devices Inc. | |
| * | |
| * (C) Copyright 2000-2004 | |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. | |
| * | |
| * Licensed under the GPL-2 or later. | |
| */ | |
| #include <common.h> | |
| #include <command.h> | |
| #include <asm/blackfin.h> | |
| #include <asm/cplb.h> | |
| #include <asm/mach-common/bits/core.h> | |
| #include <asm/mach-common/bits/ebiu.h> | |
| #include <asm/mach-common/bits/trace.h> | |
| #include "cpu.h" | |
| #include "serial.h" | |
| ulong bfin_poweron_retx; | |
| __attribute__ ((__noreturn__)) | |
| void cpu_init_f(ulong bootflag, ulong loaded_from_ldr) | |
| { | |
| extern char _stext_l1; | |
| #ifndef CONFIG_BFIN_BOOTROM_USES_EVT1 | |
| /* Build a NOP slide over the LDR jump block. Whee! */ | |
| char nops[0xC]; | |
| serial_early_puts("NOP Slide\n"); | |
| memset(nops, 0x00, sizeof(nops)); | |
| memcpy(&_stext_l1 - sizeof(nops), nops, sizeof(nops)); | |
| #endif | |
| if (!loaded_from_ldr) { | |
| /* Relocate sections into L1 if the LDR didn't do it -- don't | |
| * check length because the linker script does the size | |
| * checking at build time. | |
| */ | |
| serial_early_puts("L1 Relocate\n"); | |
| extern char _stext_l1, _etext_l1, _stext_l1_lma; | |
| memcpy(&_stext_l1, &_stext_l1_lma, (&_etext_l1 - &_stext_l1)); | |
| extern char _sdata_l1, _edata_l1, _sdata_l1_lma; | |
| memcpy(&_sdata_l1, &_sdata_l1_lma, (&_edata_l1 - &_sdata_l1)); | |
| } | |
| #if defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__) | |
| /* The BF537 bootrom will reset the EBIU_AMGCTL register on us | |
| * after it has finished loading the LDR. So configure it again. | |
| */ | |
| else | |
| bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL); | |
| #endif | |
| /* Save RETX so we can pass it while booting Linux */ | |
| bfin_poweron_retx = bootflag; | |
| #ifdef CONFIG_DEBUG_DUMP | |
| /* Turn on hardware trace buffer */ | |
| bfin_write_TBUFCTL(TBUFPWR | TBUFEN); | |
| #endif | |
| #ifndef CONFIG_PANIC_HANG | |
| /* Reset upon a double exception rather than just hanging. | |
| * Do not do bfin_read on SWRST as that will reset status bits. | |
| */ | |
| bfin_write_SWRST(DOUBLE_FAULT); | |
| #endif | |
| serial_early_puts("Board init flash\n"); | |
| board_init_f(bootflag); | |
| } | |
| int exception_init(void) | |
| { | |
| bfin_write_EVT3(trap); | |
| return 0; | |
| } | |
| int irq_init(void) | |
| { | |
| #ifdef SIC_IMASK0 | |
| bfin_write_SIC_IMASK0(0); | |
| bfin_write_SIC_IMASK1(0); | |
| # ifdef SIC_IMASK2 | |
| bfin_write_SIC_IMASK2(0); | |
| # endif | |
| #elif defined(SICA_IMASK0) | |
| bfin_write_SICA_IMASK0(0); | |
| bfin_write_SICA_IMASK1(0); | |
| #else | |
| bfin_write_SIC_IMASK(0); | |
| #endif | |
| bfin_write_EVT2(evt_default); /* NMI */ | |
| bfin_write_EVT5(evt_default); /* hardware error */ | |
| bfin_write_EVT6(evt_default); /* core timer */ | |
| bfin_write_EVT7(evt_default); | |
| bfin_write_EVT8(evt_default); | |
| bfin_write_EVT9(evt_default); | |
| bfin_write_EVT10(evt_default); | |
| bfin_write_EVT11(evt_default); | |
| bfin_write_EVT12(evt_default); | |
| bfin_write_EVT13(evt_default); | |
| bfin_write_EVT14(evt_default); | |
| bfin_write_EVT15(evt_default); | |
| bfin_write_ILAT(0); | |
| CSYNC(); | |
| /* enable hardware error irq */ | |
| irq_flags = 0x3f; | |
| local_irq_enable(); | |
| return 0; | |
| } |