| /* | |
| * U-boot - serial.c Blackfin Serial Driver | |
| * | |
| * Copyright (c) 2005-2008 Analog Devices Inc. | |
| * | |
| * Copyright (c) 2003 Bas Vermeulen <bas@buyways.nl>, | |
| * BuyWays B.V. (www.buyways.nl) | |
| * | |
| * Based heavily on: | |
| * blkfinserial.c: Serial driver for BlackFin DSP internal USRTs. | |
| * Copyright(c) 2003 Metrowerks <mwaddel@metrowerks.com> | |
| * Copyright(c) 2001 Tony Z. Kou <tonyko@arcturusnetworks.com> | |
| * Copyright(c) 2001-2002 Arcturus Networks Inc. <www.arcturusnetworks.com> | |
| * | |
| * Based on code from 68328 version serial driver imlpementation which was: | |
| * Copyright (C) 1995 David S. Miller <davem@caip.rutgers.edu> | |
| * Copyright (C) 1998 Kenneth Albanowski <kjahds@kjahds.com> | |
| * Copyright (C) 1998, 1999 D. Jeff Dionne <jeff@uclinux.org> | |
| * Copyright (C) 1999 Vladimir Gurevich <vgurevic@cisco.com> | |
| * | |
| * (C) Copyright 2000-2004 | |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. | |
| * | |
| * Licensed under the GPL-2 or later. | |
| */ | |
| /* Anomaly notes: | |
| * 05000086 - we don't support autobaud | |
| * 05000099 - we only use DR bit, so losing others is not a problem | |
| * 05000100 - we don't use the UART_IIR register | |
| * 05000215 - we poll the uart (no dma/interrupts) | |
| * 05000225 - no workaround possible, but this shouldnt cause errors ... | |
| * 05000230 - we tweak the baud rate calculation slightly | |
| * 05000231 - we always use 1 stop bit | |
| * 05000309 - we always enable the uart before we modify it in anyway | |
| * 05000350 - we always enable the uart regardless of boot mode | |
| * 05000363 - we don't support break signals, so don't generate one | |
| */ | |
| #include <common.h> | |
| #include <watchdog.h> | |
| #include <asm/blackfin.h> | |
| #include <asm/mach-common/bits/uart.h> | |
| #ifdef CONFIG_UART_CONSOLE | |
| #if defined(UART_LSR) && (CONFIG_UART_CONSOLE != 0) | |
| # error CONFIG_UART_CONSOLE must be 0 on parts with only one UART | |
| #endif | |
| #include "serial.h" | |
| #ifdef CONFIG_DEBUG_SERIAL | |
| uint16_t cached_lsr[256]; | |
| uint16_t cached_rbr[256]; | |
| size_t cache_count; | |
| /* The LSR is read-to-clear on some parts, so we have to make sure status | |
| * bits aren't inadvertently lost when doing various tests. This also | |
| * works around anomaly 05000099 at the same time by keeping a cumulative | |
| * tally of all the status bits. | |
| */ | |
| static uint16_t uart_lsr_save; | |
| static uint16_t uart_lsr_read(void) | |
| { | |
| uint16_t lsr = *pUART_LSR; | |
| uart_lsr_save |= (lsr & (OE|PE|FE|BI)); | |
| return lsr | uart_lsr_save; | |
| } | |
| /* Just do the clear for everyone since it can't hurt. */ | |
| static void uart_lsr_clear(void) | |
| { | |
| uart_lsr_save = 0; | |
| *pUART_LSR |= -1; | |
| } | |
| #else | |
| /* When debugging is disabled, we only care about the DR bit, so if other | |
| * bits get set/cleared, we don't really care since we don't read them | |
| * anyways (and thus anomaly 05000099 is irrelevant). | |
| */ | |
| static inline uint16_t uart_lsr_read(void) { return *pUART_LSR; } | |
| static inline void uart_lsr_clear(void) { *pUART_LSR = -1; } | |
| #endif | |
| /* Symbol for our assembly to call. */ | |
| void serial_set_baud(uint32_t baud) | |
| { | |
| serial_early_set_baud(baud); | |
| } | |
| /* Symbol for common u-boot code to call. | |
| * Setup the baudrate (brg: baudrate generator). | |
| */ | |
| void serial_setbrg(void) | |
| { | |
| DECLARE_GLOBAL_DATA_PTR; | |
| serial_set_baud(gd->baudrate); | |
| } | |
| /* Symbol for our assembly to call. */ | |
| void serial_initialize(void) | |
| { | |
| serial_early_init(); | |
| } | |
| /* Symbol for common u-boot code to call. */ | |
| int serial_init(void) | |
| { | |
| serial_initialize(); | |
| serial_setbrg(); | |
| uart_lsr_clear(); | |
| #ifdef CONFIG_DEBUG_SERIAL | |
| cache_count = 0; | |
| memset(cached_lsr, 0x00, sizeof(cached_lsr)); | |
| memset(cached_rbr, 0x00, sizeof(cached_rbr)); | |
| #endif | |
| return 0; | |
| } | |
| void serial_putc(const char c) | |
| { | |
| /* send a \r for compatibility */ | |
| if (c == '\n') | |
| serial_putc('\r'); | |
| WATCHDOG_RESET(); | |
| /* wait for the hardware fifo to clear up */ | |
| while (!(uart_lsr_read() & THRE)) | |
| continue; | |
| /* queue the character for transmission */ | |
| *pUART_THR = c; | |
| SSYNC(); | |
| WATCHDOG_RESET(); | |
| } | |
| int serial_tstc(void) | |
| { | |
| WATCHDOG_RESET(); | |
| return (uart_lsr_read() & DR) ? 1 : 0; | |
| } | |
| int serial_getc(void) | |
| { | |
| uint16_t uart_rbr_val; | |
| /* wait for data ! */ | |
| while (!serial_tstc()) | |
| continue; | |
| /* grab the new byte */ | |
| uart_rbr_val = *pUART_RBR; | |
| #ifdef CONFIG_DEBUG_SERIAL | |
| /* grab & clear the LSR */ | |
| uint16_t uart_lsr_val = uart_lsr_read(); | |
| cached_lsr[cache_count] = uart_lsr_val; | |
| cached_rbr[cache_count] = uart_rbr_val; | |
| cache_count = (cache_count + 1) % ARRAY_SIZE(cached_lsr); | |
| if (uart_lsr_val & (OE|PE|FE|BI)) { | |
| uint16_t dll, dlh; | |
| printf("\n[SERIAL ERROR]\n"); | |
| ACCESS_LATCH(); | |
| dll = *pUART_DLL; | |
| dlh = *pUART_DLH; | |
| ACCESS_PORT_IER(); | |
| printf("\tDLL=0x%x DLH=0x%x\n", dll, dlh); | |
| do { | |
| --cache_count; | |
| printf("\t%3i: RBR=0x%02x LSR=0x%02x\n", cache_count, | |
| cached_rbr[cache_count], cached_lsr[cache_count]); | |
| } while (cache_count > 0); | |
| return -1; | |
| } | |
| #endif | |
| uart_lsr_clear(); | |
| return uart_rbr_val; | |
| } | |
| void serial_puts(const char *s) | |
| { | |
| while (*s) | |
| serial_putc(*s++); | |
| } | |
| #endif |