| |
| /* |
| * arch/arm/include/asm/arch-gxtvbb/cpu_sdio.h |
| * |
| * Copyright (C) 2015 Amlogic, Inc. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| * |
| * You should have received a copy of the GNU General Public License along |
| * with this program; if not, write to the Free Software Foundation, Inc., |
| * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. |
| */ |
| |
| #ifndef __CPU_SDIO_H__ |
| #define __CPU_SDIO_H__ |
| |
| #define SD_EMMC_BASE_A 0xd0070000 |
| #define SD_EMMC_BASE_B 0xd0072000 |
| #define SD_EMMC_BASE_C 0xd0074000 |
| |
| #define SDIO_PORT_A 0 |
| #define SDIO_PORT_B 1 |
| #define SDIO_PORT_C 2 |
| |
| #define Cfg_div 0 |
| #define Cfg_src 6 |
| #define Cfg_co_phase 8 |
| #define Cfg_tx_phase 10 |
| #define Cfg_rx_phase 12 |
| #define Cfg_sram_pd 14 |
| #define Cfg_tx_delay 16 |
| #define Cfg_rx_delay 20 |
| #define Cfg_always_on 24 |
| #define Cfg_irq_sdio_sleep 25 |
| #define Cfg_irq_sdio_sleep_ds 26 |
| |
| #define SD_EMMC_RXD_ERROR 1 |
| #define SD_EMMC_TXD_ERROR 1<<1 |
| #define SD_EMMC_DESC_ERROR 1<<2 |
| #define SD_EMMC_RESP_CRC_ERROR 1<<3 |
| #define SD_EMMC_RESP_TIMEOUT_ERROR 1<<4 |
| #define SD_EMMC_DESC_TIMEOUT_ERROR 1<<5 |
| |
| struct sd_emmc_global_regs { |
| volatile uint32_t gclock; // 0x00 |
| volatile uint32_t gdelay; // 0x04 |
| volatile uint32_t gadjust; // 0x08 |
| volatile uint32_t reserved_0c; // 0x0c |
| volatile uint32_t gcalout; // 0x10 |
| volatile uint32_t reserved_14[11]; // 0x14~0x3c |
| volatile uint32_t gstart; // 0x40 |
| volatile uint32_t gcfg; // 0x44 |
| volatile uint32_t gstatus; // 0x48 |
| volatile uint32_t girq_en; // 0x4c |
| volatile uint32_t gcmd_cfg; // 0x50 |
| volatile uint32_t gcmd_arg; // 0x54 |
| volatile uint32_t gcmd_dat; // 0x58 |
| volatile uint32_t gcmd_rsp0; // 0x5c |
| volatile uint32_t gcmd_rsp1; // 0x60 |
| volatile uint32_t gcmd_rsp2; // 0x64 |
| volatile uint32_t gcmd_rsp3; // 0x68 |
| volatile uint32_t reserved_6c; // 0x6c |
| volatile uint32_t gcurr_cfg; // 0x70 |
| volatile uint32_t gcurr_arg; // 0x74 |
| volatile uint32_t gcurr_dat; // 0x78 |
| volatile uint32_t gcurr_rsp; // 0x7c |
| volatile uint32_t gnext_cfg; // 0x80 |
| volatile uint32_t gnext_arg; // 0x84 |
| volatile uint32_t gnext_dat; // 0x88 |
| volatile uint32_t gnext_rsp; // 0x8c |
| volatile uint32_t grxd; // 0x90 |
| volatile uint32_t gtxd; // 0x94 |
| volatile uint32_t reserved_98[90]; // 0x98~0x1fc |
| volatile uint32_t gdesc[128]; // 0x200 |
| volatile uint32_t gping[128]; // 0x400 |
| volatile uint32_t gpong[128]; // 0x800 |
| }; |
| |
| union sd_emmc_setup { |
| uint32_t d32; |
| struct { |
| unsigned bw:3; |
| unsigned fast:1; |
| unsigned par:3; |
| unsigned hcs:1; |
| unsigned sd:1; |
| unsigned sdhc:1; |
| unsigned type:6; |
| unsigned rca:16; |
| } b; |
| }; |
| |
| struct sd_emmc_desc_info{ |
| uint32_t cmd_info; |
| uint32_t cmd_arg; |
| uint32_t data_addr; |
| uint32_t resp_addr; |
| }; |
| |
| struct cmd_cfg{ |
| uint32_t length:9; |
| uint32_t block_mode:1; |
| uint32_t r1b:1; |
| uint32_t end_of_chain:1; |
| uint32_t timeout:4; |
| uint32_t no_resp:1; |
| uint32_t no_cmd:1; |
| uint32_t data_io:1; |
| uint32_t data_wr:1; |
| uint32_t resp_nocrc:1; |
| uint32_t resp_128:1; |
| uint32_t resp_num:1; |
| uint32_t data_num:1; |
| uint32_t cmd_index:6; |
| uint32_t error:1; |
| uint32_t owner:1; |
| }; |
| |
| struct sd_emmc_status{ |
| uint32_t rxd_err:8; /*[7:0] RX data CRC error per wire, for multiple block read, the CRC errors are ORed together.*/ |
| uint32_t txd_err:1; /*[8] TX data CRC error, for multiple block write, any one of blocks CRC error. */ |
| uint32_t desc_err:1; /*[9] SD/eMMC controller doesn¡¯t own descriptor. The owner bit is ¡°0¡±, set cfg_ignore_owner to ignore this error.*/ |
| uint32_t resp_err:1; /*[10] Response CRC error.*/ |
| uint32_t resp_timeout:1; /*[11] No response received before time limit. The timeout limit is set by cfg_resp_timeout.*/ |
| uint32_t desc_timeout:1; /*[12] Descriptor execution time over time limit. The timeout limit is set by descriptor itself.*/ |
| /* Consider the multiple block read/write, set the proper timeout limits.*/ |
| uint32_t end_of_chain:1; /*[13] End of Chain IRQ, Normal IRQ. */ |
| uint32_t desc_irq:1; /*[14] This descriptor requests an IRQ, Normal IRQ, the descriptor chain execution keeps going on.*/ |
| uint32_t irq_sdio:1; /*[15] SDIO device uses DAT[1] to request IRQ. */ |
| uint32_t dat_i:8; /*[23:16] Input data signals. */ |
| uint32_t cmd_i:1; /*[24] nput response signal. */ |
| uint32_t ds:1; /*[25] Input data strobe. */ |
| uint32_t bus_fsm:1; /*[30:28] BUS fsm */ |
| uint32_t desc_wr_rdy:1; /*[31] Descriptor write back process is done and it is ready for CPU to read.*/ |
| };//__attribute__((__may_alias__)); |
| |
| |
| struct sd_emmc_clock{ |
| uint32_t div:6; /*[5:0] Clock divider. Frequency = clock source/cfg_div, Maximum divider 63. */ |
| /*Clock off: cfg_div==0, the clock is disabled */ |
| /*Divider bypass: cfg_div==1, clock source is used as core clock without divider. */ |
| uint32_t src:2; /*[7:6] Clock source, 0: Crystal 24MHz, 1: Fix PLL, 850MHz*/ |
| /* 2: MPLL, <637MHz, used for 400MHz exactly. 3: different PLL */ |
| uint32_t core_phase:2; /*[9:8] Core clock phase. 0: 0 phase, 1: 90 phase, 2: 180 phase, 3: 270 phase.*/ |
| uint32_t tx_phase:2; /*[11:10] TX clock phase. 0: 0 phase, 1: 90 phase, 2: 180 phase, 3: 270 phase.*/ |
| uint32_t rx_phase:2; /*[13:12] RX clock phase. 0: 0 phase, 1: 90 phase, 2: 180 phase, 3: 270 phase.*/ |
| uint32_t reserved14:2; |
| uint32_t tx_delay:4; /*[19:16] TX clock delay line. 0: no delay, n: delay n*200ps. Maximum delay 3ns.*/ |
| uint32_t rx_delay:4; /*[23:20] RX clock delay line. 0: no delay, n: delay n*200ps. Maximum delay 3ns.*/ |
| uint32_t always_on:1; /*[24] 1: Keep clock always on. 0: Clock on/off controlled by activities. */ |
| /*Any APB3 access or descriptor execution will keep clock on.*/ |
| uint32_t irq_sdio_sleep:1; /*[25] 1: enable IRQ sdio when in sleep mode. */ |
| uint32_t reserved26:6; |
| }; |
| |
| struct sd_emmc_delay{ |
| uint32_t dat0:4; /*[3:0] Data 0 delay line. */ |
| uint32_t dat1:4; /*[7:4] Data 1 delay line. */ |
| uint32_t dat2:4; /*[11:8] Data 2 delay line. */ |
| uint32_t dat3:4; /*[15:12] Data 3 delay line. */ |
| uint32_t dat4:4; /*[19:16] Data 4 delay line. */ |
| uint32_t dat5:4; /*[23:20] Data 5 delay line. */ |
| uint32_t dat6:4; /*[27:24] Data 6 delay line. */ |
| uint32_t dat7:4; /*[31:28] Data 7 delay line. */ |
| }; |
| |
| |
| struct sd_emmc_adjust{ |
| uint32_t cmd_delay:4; /*[3:0] Command delay line. */ |
| uint32_t ds_delay:4; /*[7:4] DS delay line. */ |
| uint32_t cali_sel:4; /*[11:8] Select one signal to be tested.*/ |
| /*Signals are labeled from 0 to 9 the same as delay lines. */ |
| uint32_t cali_enable:1; /*[12] Enable calibration. */ |
| uint32_t adj_enable:1; /*[13] Adjust interface timing by resampling the input signals. */ |
| uint32_t cali_rise:1; /*[14] 1: test the rising edge. 0: test the falling edge. */ |
| uint32_t reserved15:1; |
| uint32_t adj_delay:6; /*[21:16] Resample the input signals when clock index==adj_delay. */ |
| uint32_t reserved22:10; |
| }; |
| |
| |
| struct sd_emmc_calout{ |
| uint32_t cali_idx:6; /*[5:0] Calibration reading. The event happens at this index. */ |
| uint32_t reserved6:1; |
| uint32_t cali_vld:1; /*[7] The reading is valid. */ |
| uint32_t cali_setup:8; /*[15:8] Copied from BASE+0x8 [15:8] include cali_sel, cali_enable, adj_enable, cali_rise. */ |
| uint32_t reserved16:16; |
| }; |
| |
| |
| struct sd_emmc_start{ |
| uint32_t init:1; /*[0] 1: Read descriptor from internal SRAM, limited to 32 descriptors. */ |
| /* 0: Read descriptor from external DDR */ |
| uint32_t busy:1; /*[1] 1: Start command chain execution process. 0: Stop */ |
| uint32_t addr:30; /*[31:2] Descriptor address, the last 2 bits are 0, 4 bytes aligned. */ |
| /* When internal SRAM is used, the valid address range is from 0x200~0x3ff */ |
| /* When external DDR is used, the valid address is anywhere in DDR, the length of chain is unlimited.*/ |
| };//__attribute__((__may_alias__)); |
| |
| |
| struct sd_emmc_config{ |
| uint32_t bus_width:2; /*[1:0] 0: 1 bit, 1: 4 bits, 2: 8 bits, 3: 2 bits (not supported)*/ |
| uint32_t ddr:1; /*[2] 1: DDR mode, 0: SDR mode */ |
| uint32_t dc_ugt:1; /*[3] 1: DDR access urgent, 0: DDR access normal. */ |
| uint32_t bl_len:4; /*[7:4] Block length 2^cfg_bl_len, because internal buffer size is limited to 512 bytes, the cfg_bl_len <=9. */ |
| uint32_t resp_timeout:4; /*[11:8] Wait response till 2^cfg_resp_timeout core clock cycles. Maximum 32768 core cycles. */ |
| uint32_t rc_cc:4; /*[15:12] Wait response-command, command-command gap before next command, 2^cfg_rc_cc core clock cycles. */ |
| uint32_t out_fall:1; /*[16] DDR mode only. The command and TXD start from rising edge. Set 1 to start from falling edge. */ |
| uint32_t blk_gap_ip:1; /*[17] 1: Enable SDIO data block gap interrupt period. 0: Disabled.*/ |
| uint32_t spare:1; /*[18] Spare, ??? need check*/ |
| uint32_t ignore_owner:1; /*[19] Use this descriptor even if its owner bit is ¡°0¡±.*/ |
| uint32_t chk_ds:1; /*[20] Check data strobe in HS400.*/ |
| uint32_t cmd_low:1; /*[21] Hold CMD as output Low, eMMC boot mode.*/ |
| uint32_t stop_clk:1; /*[22] 1: stop clock. 0: normal clock.*/ |
| /*In normal mode, the clock is automatically on/off during reading mode to back off reading in case of*/ |
| /*DDR slow response, stop clock is used in voltage switch.*/ |
| uint32_t auto_clk:1; /*[23] 1: when BUS is idle and no descriptor is available, turn off clock, to save power.*/ |
| /* 0: core clock is always on.*/ |
| uint32_t txd_add_err:1; /*[24] TXD add error test*/ |
| /*Test feature, should not be used in normal condition.*/ |
| /*It will inverted the first CRC bits of the 3rd block.*/ |
| /*Block index starts from 0, 1, 2, ¡*/ |
| uint32_t txd_retry:1; /*[25] When TXD CRC error, host sends the block again.*/ |
| /*The total number of retries of one descriptor is limited to 15, */ |
| /*after 15 retries, the TXD_err is set to high.*/ |
| uint32_t revd:8; /*[31:26] reved*/ |
| };//__attribute__((__may_alias__)); |
| |
| |
| struct sd_emmc_irq_en{ |
| uint32_t rxd_err:8; /*[7:0] RX data CRC error per wire.*/ |
| uint32_t txd_err:1; /*[8] TX data CRC error. */ |
| uint32_t desc_err:1; /*[9] SD/eMMC controller doesn¡¯t own descriptor. */ |
| uint32_t resp_err:1; /*[10] Response CRC error.*/ |
| uint32_t resp_timeout:1; /*[11] No response received before time limit. */ |
| uint32_t desc_timeout:1; /*[12] Descriptor execution time over time limit. */ |
| uint32_t end_of_chain:1; /*[13] End of Chain IRQ. */ |
| uint32_t desc_irq:1; /*[14] This descriptor requests an IRQ. */ |
| uint32_t irq_sdio:1; /*[15] Enable sdio interrupt. */ |
| uint32_t revd:16; /*[31:16] reved*/ |
| }; |
| |
| struct sd_emmc_data_info{ |
| uint32_t cnt:10; /*[9:0] Rxd words received from BUS. Txd words received from DDR.*/ |
| uint32_t blk:9; /*[24:16] Rxd Blocks received from BUS. Txd blocks received from DDR.*/ |
| uint32_t revd:30; /*[31:17] Reved. */ |
| }; |
| |
| |
| struct sd_emmc_card_info{ |
| uint32_t txd_cnt:10; /*[9:0] Txd BUS cycle counter. */ |
| uint32_t txd_blk:9; /*[24:16] Txd BUS block counter.*/ |
| uint32_t revd:30; /*[31:17] Reved. */ |
| }; |
| |
| #endif |