| |
| /* |
| * board/amlogic/configs/g12a_estelle_bx.h |
| * |
| * Copyright (C) 2015 Amlogic, Inc. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| * |
| * You should have received a copy of the GNU General Public License along |
| * with this program; if not, write to the Free Software Foundation, Inc., |
| * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. |
| */ |
| |
| #ifndef __G12A_S905D2_ESTELLE_BX_V1_H__ |
| #define __G12A_S905D2_ESTELLE_BX_V1_H__ |
| |
| #include <asm/arch/cpu.h> |
| |
| #define CONFIG_SYS_GENERIC_BOARD 1 |
| #ifndef CONFIG_AML_MESON |
| #warning "include warning" |
| #endif |
| |
| #define CONFIG_ABR_WEAR_LEVELING |
| #define CONFIG_ZIRCON_BOOT_IMAGE |
| #define CONFIG_ZIRCON_VBOOT |
| #define CONFIG_LIBAVB |
| #define CONFIG_USE_ROLLBACK_IN_FUSE |
| #define CONFIG_WDT |
| |
| #define CONFIG_USB_GADGET |
| #define CONFIG_CMD_FASTBOOT |
| #define CONFIG_SYS_CACHELINE_SIZE 64 |
| #define CONFIG_FASTBOOT_FLASH_NAND_DEV |
| #define CONFIG_FASTBOOT_FLASH |
| #define CONFIG_DEVICE_PRODUCT "Google Home Hub" |
| |
| /* Timeout of 0 will only check any buffered keys, but will then continue |
| immediately. This turns out to be sufficient for us, since a user can hit |
| the fastboot key any time prior to this during boot and we'll still see it |
| when flushing the buffer. */ |
| #define CONFIG_FORCE_FASTBOOT_TIMEOUT_MS 0 |
| |
| #define CONFIG_G_DNL_MANUFACTURER "Google" |
| #define CONFIG_G_DNL_VENDOR_NUM 0x18d1 |
| #define CONFIG_G_DNL_PRODUCT_NUM 0x4ee0 |
| |
| /* DRAM Layout |
| * 0x00000000 ----------------------------------------- |
| * RSV (16 MiB) (Usable by kernel) |
| * 0x01000000 ----------------------------------------- |
| * Device Tree (512 KiB) (Unused) |
| * 0x01080000 ----------------------------------------- |
| * Default Kernel Location (63.5 MiB) |
| * 0x05000000 ----------------------------------------- |
| * BL31/32 Reserved (35 MiB) |
| * 0x07300000 ----------------------------------------- |
| * LastKmsg (Unused) |
| * 0x07400000 ----------------------------------------- |
| * Fastboot Buffer Location (512 MiB) |
| * 0x27400000 ----------------------------------------- |
| * Unused (512 MiB) |
| * 0x47400000 ----------------------------------------- |
| * U-Boot Code + Stack + Heap (268 MiB) |
| * 0x58000000 ----------------------------------------- |
| * RSV (128 MiB) |
| * - board cfg file? |
| * 0x5f7fe000 - 0x5f800000 (8 KiB) |
| * - NVRAM region |
| * 0x5f800000 - 0x60000000 (8 MiB) |
| * - marked as reserved to zircon |
| * 0x60000000 ----------------------------------------- |
| */ |
| #define CONFIG_DEFAULT_KERNEL_ADDR 0x01080000 |
| #define CONFIG_DEFAULT_KERNEL_SIZE 0x03f80000 |
| #define CONFIG_USB_FASTBOOT_BUF_ADDR 0x07400000 |
| #define CONFIG_USB_FASTBOOT_BUF_SIZE 0x20000000 |
| |
| /* |
| * platform power init config |
| */ |
| #define CONFIG_PLATFORM_POWER_INIT |
| #define CONFIG_VCCK_INIT_VOLTAGE 800 // VCCK power up voltage |
| #define CONFIG_VDDEE_INIT_VOLTAGE 840 // VDDEE power up voltage |
| #define CONFIG_VDDEE_SLEEP_VOLTAGE 731 // VDDEE suspend voltage |
| |
| /* SMP Definitinos */ |
| #define CPU_RELEASE_ADDR secondary_boot_func |
| |
| /* Bootloader Control Block function |
| That is used for recovery and the bootloader to talk to each other |
| */ |
| #define CONFIG_BOOTLOADER_CONTROL_BLOCK |
| |
| /* Serial config */ |
| #define CONFIG_CONS_INDEX 2 |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_AML_MESON_SERIAL 1 |
| #define CONFIG_SERIAL_MULTI 1 |
| |
| //Enable ir remote wake up for bl30 |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL1 0xef10fe01 //amlogic tv ir --- power |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL2 0XBB44FB04 //amlogic tv ir --- ch+ |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL3 0xF20DFE01 //amlogic tv ir --- ch- |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL4 0xFFFFFFFF |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL5 0xe51afb04 |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL6 0xFFFFFFFF |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL7 0xFFFFFFFF |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL8 0xFFFFFFFF |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL9 0xFFFFFFFF |
| |
| /*config the default parameters for adc power key*/ |
| #define CONFIG_ADC_POWER_KEY_CHAN 2 /*channel range: 0-7*/ |
| #define CONFIG_ADC_POWER_KEY_VAL 0 /*sample value range: 0-1023*/ |
| |
| /* args/envs */ |
| #define CONFIG_SYS_MAXARGS 64 |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "loadaddr="__stringify(CONFIG_DEFAULT_KERNEL_ADDR)"\0" \ |
| "loadsize="__stringify(CONFIG_DEFAULT_KERNEL_SIZE)"\0" \ |
| "outputmode=panel\0" \ |
| "hdmimode=1080p60hz\0" \ |
| "display_width=1920\0" \ |
| "display_height=1080\0" \ |
| "display_bpp=16\0" \ |
| "display_color_index=16\0" \ |
| "display_layer=osd0\0" \ |
| "display_color_fg=0xffff\0" \ |
| "display_color_bg=0\0" \ |
| "dtb_mem_addr=0x1000000\0" \ |
| "fb_addr=0x5f800000\0" \ |
| "fb_width=608\0" \ |
| "fb_height=1024\0" \ |
| "usb_burning=update 1000\0" \ |
| "fdt_high=0x20000000\0" \ |
| "try_auto_burn=update 700 750;\0" \ |
| "sdcburncfg=aml_sdc_burn.ini\0" \ |
| "sdc_burning=sdc_burn ${sdcburncfg}\0" \ |
| "wipe_data=successful\0" \ |
| "wipe_cache=successful\0" \ |
| "EnableSelinux=enforcing\0" \ |
| "storeargs=" \ |
| "get_rebootmode;" \ |
| "setenv bootargs " \ |
| "logo=${display_layer},loaded,${fb_addr} " \ |
| "vout=${outputmode},enable " \ |
| "panel_type=${panel_type} " \ |
| "test_mode=${test_mode} " \ |
| "androidboot.reboot_mode=${reboot_mode} " \ |
| "ramoops.mem_address=0x20000000 ramoops.mem_size=0x100000 ramoops.record_size=0x8000 ramoops.console_size=0x8000 " \ |
| "hw_id=${hw_id};" \ |
| "setenv bootargs ${bootargs} " \ |
| "androidboot.hardware="__stringify(BOARD_NAME)";" \ |
| "\0" \ |
| "switch_bootmode=" \ |
| "get_rebootmode;" \ |
| "if test ${reboot_mode} = factory_reset; then " \ |
| "run recovery_from_flash;" \ |
| "else if test ${reboot_mode} = update; then " \ |
| "run update;" \ |
| "else if test ${reboot_mode} = cold_boot; then " \ |
| /* "run try_auto_burn;" */ \ |
| "else if test ${reboot_mode} = fastboot; then " \ |
| "fastboot;" \ |
| "fi;fi;fi;fi;" \ |
| "\0" \ |
| "storeboot=" \ |
| /* zvb_load_and_boot doesn't return on success */ \ |
| "zvb_load_and_boot kernel ${loadaddr} ${loadsize};" \ |
| "run update;" \ |
| "\0" \ |
| "factory_reset_poweroff_protect=" \ |
| "echo wipe_data=${wipe_data};" \ |
| "echo wipe_cache=${wipe_cache};" \ |
| "if test ${wipe_data} = failed; then " \ |
| "run init_display;" \ |
| "run get_hw_id;" \ |
| "run storeargs;" \ |
| "run recovery_from_flash;" \ |
| "fi;" \ |
| "if test ${wipe_cache} = failed; then " \ |
| "run init_display;" \ |
| "run get_hw_id;" \ |
| "run storeargs;" \ |
| "run recovery_from_flash;" \ |
| "fi;" \ |
| "\0" \ |
| "update=" \ |
| "run usb_burning;" \ |
| "run recovery_from_flash;" \ |
| "\0" \ |
| /* load and boot an image from 'recovery' partition to restore the device. */ \ |
| "recovery_from_flash=" \ |
| "zvb_load_and_boot recovery ${loadaddr} ${loadsize};" \ |
| "\0" \ |
| "reset_ddic=" \ |
| "gpio clear GPIOH_6" \ |
| "\0" \ |
| "detect_panel=" \ |
| "if gpio input GPIOH_5; then " \ |
| "setenv panel_type lcd_3;" \ |
| "else " \ |
| "setenv panel_type lcd_4;" \ |
| "fi;" \ |
| "\0" \ |
| "start_backlight=" \ |
| "if ubifsload 0x8000000 bl_calibration.txt; then " \ |
| "configure_backlight 0x8000000;" \ |
| "else " \ |
| "configure_backlight;" \ |
| "fi;" \ |
| "\0"\ |
| "init_display=" \ |
| "run reset_ddic;" \ |
| "check_fdr_for_backlight_brightness;" \ |
| "run detect_panel;" \ |
| "osd open;" \ |
| "osd clear;" \ |
| "osd setcolor 0x5b0d5b0d;" \ |
| "ubi part factory;" \ |
| "ubifsmount ubi0:factory;" \ |
| /* do this sequentially so we could reuse the address and do |
| * not need to know the size of the images */ \ |
| "mw 0x8000000 0 1;" \ |
| "ubifsload 0x8000000 logo.bmp;" \ |
| "bmp display 0x8000000;" \ |
| "mw 0x8000000 0 1;" \ |
| "ubifsload 0x8000000 corner_BL.bmp;" \ |
| "bmp display 0x8000000 0 1008;" \ |
| "mw 0x8000000 0 1;" \ |
| "ubifsload 0x8000000 corner_BR.bmp;" \ |
| "bmp display 0x8000000 592 1008;" \ |
| "mw 0x8000000 0 1;" \ |
| "ubifsload 0x8000000 corner_TL.bmp;" \ |
| "bmp display 0x8000000 0 0;" \ |
| "mw 0x8000000 0 1;" \ |
| "ubifsload 0x8000000 corner_TR.bmp;" \ |
| "bmp display 0x8000000 592 0;" \ |
| "bmp scale;" \ |
| "vout output ${outputmode};" \ |
| "run start_backlight;" \ |
| "ubifsumount;" \ |
| "\0" \ |
| "get_hw_id=" \ |
| "get_estelle_hw_id;" \ |
| "\0" \ |
| "upgrade_key=" \ |
| "setenv boot_external_image 0;" \ |
| "if gpio input GPIOZ_6; then " \ |
| "echo detect VOL_DN pressed;" \ |
| "run recovery_from_flash;" \ |
| "else " \ |
| "if gpio input GPIOZ_5; then " \ |
| "echo detect VOL_UP pressed;" \ |
| "if gpio input GPIOZ_2; then " \ |
| "echo MUTE not engaged, starting fastboot;" \ |
| "fastboot;" \ |
| "else " \ |
| "echo MUTE engaged, skipping fastboot;" \ |
| "fi;" \ |
| "else " \ |
| "echo upgrade key not pressed;" \ |
| "fi;" \ |
| "fi;" \ |
| "if force_fastboot_mode; then " \ |
| "echo fastboot mode was requested;" \ |
| "fastboot;" \ |
| "fi;" \ |
| "\0" \ |
| |
| |
| #define CONFIG_PREBOOT \ |
| "run factory_reset_poweroff_protect;" \ |
| "run init_display;" \ |
| "run get_hw_id;" \ |
| "run storeargs;" \ |
| "run upgrade_key;" \ |
| "run switch_bootmode;" |
| |
| #define CONFIG_BOOTCOMMAND "run storeboot;" |
| |
| #define CONFIG_ENV_IS_NOWHERE 1 |
| #define CONFIG_SHORT_RSV 1 |
| #define RESERVED_BLOCK_NUM 8 |
| #define CONFIG_ENV_SIZE (64*1024) |
| #define CONFIG_FIT 1 |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_ANDROID_BOOT_IMAGE 1 |
| #define CONFIG_ANDROID_IMG 1 |
| #define CONFIG_SYS_BOOTM_LEN (64<<20) /* Increase max gunzip size*/ |
| |
| /* cpu */ |
| #define CONFIG_CPU_CLK 1200 //MHz. Range: 360-2000, should be multiple of 24 |
| |
| /* ATTENTION */ |
| /* DDR configs move to board/amlogic/[board]/firmware/timing.c */ |
| |
| #define CONFIG_NR_DRAM_BANKS 1 |
| /* ddr functions */ |
| #define CONFIG_DDR_FULL_TEST 0 //0:disable, 1:enable. ddr full test |
| #define CONFIG_CMD_DDR_D2PLL 0 //0:disable, 1:enable. d2pll cmd |
| #define CONFIG_CMD_DDR_TEST 0 //0:disable, 1:enable. ddrtest cmd |
| #define CONFIG_DDR_LOW_POWER 0 //0:disable, 1:enable. ddr clk gate for lp |
| #define CONFIG_DDR_ZQ_PD 0 //0:disable, 1:enable. ddr zq power down |
| #define CONFIG_DDR_USE_EXT_VREF 0 //0:disable, 1:enable. ddr use external vref |
| #define CONFIG_DDR4_TIMING_TEST 0 //0:disable, 1:enable. ddr4 timing test function |
| #define CONFIG_DDR_PLL_BYPASS 0 //0:disable, 1:enable. ddr pll bypass function |
| |
| /* storage: emmc/nand/sd */ |
| #define CONFIG_STORE_COMPATIBLE 1 |
| #define CONFIG_ENV_OVERWRITE |
| #define CONFIG_CMD_SAVEENV |
| /* fixme, need fix*/ |
| |
| #if (defined(CONFIG_ENV_IS_IN_AMLNAND) || defined(CONFIG_ENV_IS_IN_MMC)) && defined(CONFIG_STORE_COMPATIBLE) |
| #error env in amlnand/mmc already be compatible; |
| #endif |
| |
| /* |
| * storage |
| * |---------|---------| |
| * | | |
| * emmc<--Compatible-->nand |
| * |-------|-------| |
| * | | |
| * MTD<-Exclusive->NFTL |
| */ |
| /* axg only support slc nand */ |
| /* swither for mtd nand which is for slc only. */ |
| /* support for mtd */ |
| #define CONFIG_AML_MTD 1 |
| /* support for nftl */ |
| //#define CONFIG_AML_NAND 1 |
| #define CONFIG_NOT_SKIP_BAD_BLOCK 1 |
| |
| /* support nand fts*/ |
| #define CONFIG_NAND_FTS 1 |
| |
| #if defined(CONFIG_AML_NAND) && defined(CONFIG_AML_MTD) |
| #error CONFIG_AML_NAND/CONFIG_AML_MTD can not support at the sametime; |
| #endif |
| |
| #ifdef CONFIG_AML_MTD |
| |
| /* bootlaoder is construct by bl2 and fip |
| * when DISCRETE_BOOTLOADER is enabled, bl2 & fip |
| * will not be stored continuously, and nand layout |
| * would be bl2|rsv|fip|normal, but not |
| * bl2|fip|rsv|noraml anymore |
| */ |
| #define CONFIG_DISCRETE_BOOTLOADER |
| |
| #ifdef CONFIG_DISCRETE_BOOTLOADER |
| #define CONFIG_TPL_SIZE_PER_COPY 0x200000 |
| #define CONFIG_TPL_COPY_NUM 4 |
| #define CONFIG_TPL_PART_NAME "tpl" |
| /* for bl2, restricted by romboot */ |
| #define CONFIG_BL2_COPY_NUM 8 |
| #endif /* CONFIG_DISCRETE_BOOTLOADER */ |
| |
| #define CONFIG_CMD_NAND 1 |
| #define CONFIG_MTD_DEVICE y |
| /* mtd parts of ourown.*/ |
| #define CONFIFG_AML_MTDPART 1 |
| /* mtd parts by env default way.*/ |
| /* |
| #define MTDIDS_NAME_STR "aml_nand.0" |
| #define MTDIDS_DEFAULT "nand1=" MTDIDS_NAME_STR |
| #define MTDPARTS_DEFAULT "mtdparts=" MTDIDS_NAME_STR ":" \ |
| "3M@8192K(logo)," \ |
| "10M(recovery)," \ |
| "8M(kernel)," \ |
| "40M(rootfs)," \ |
| "-(data)" |
| */ |
| #define CONFIG_CMD_UBI |
| #define CONFIG_CMD_UBIFS |
| #define CONFIG_RBTREE |
| #define CONFIG_CMD_NAND_TORTURE 1 |
| #define CONFIG_CMD_MTDPARTS 1 |
| #define CONFIG_MTD_PARTITIONS 1 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 2 |
| #define CONFIG_SYS_NAND_BASE_LIST {0} |
| #endif |
| /* endof CONFIG_AML_MTD */ |
| #define CONFIG_AML_SD_EMMC 1 |
| #ifdef CONFIG_AML_SD_EMMC |
| #define CONFIG_GENERIC_MMC 1 |
| #define CONFIG_CMD_MMC 1 |
| #define CONFIG_CMD_GPT 1 |
| #define CONFIG_SYS_MMC_ENV_DEV 1 |
| #define CONFIG_EMMC_DDR52_EN 0 |
| #define CONFIG_EMMC_DDR52_CLK 35000000 |
| #endif |
| #define CONFIG_PARTITIONS 1 |
| #define CONFIG_SYS_NO_FLASH 1 |
| |
| #if defined CONFIG_AML_MTD || defined CONFIG_SPI_NAND |
| #define CONFIG_CMD_NAND 1 |
| #define CONFIG_MTD_DEVICE y |
| #define CONFIG_RBTREE |
| #define CONFIG_CMD_NAND_TORTURE 1 |
| #define CONFIG_CMD_MTDPARTS 1 |
| #define CONFIG_MTD_PARTITIONS 1 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 2 |
| #define CONFIG_SYS_NAND_BASE_LIST {0} |
| #endif |
| |
| /* vpu */ |
| #define CONFIG_AML_VPU 1 |
| //#define CONFIG_VPU_CLK_LEVEL_DFT 7 |
| |
| /* DISPLAY & HDMITX */ |
| #define CONFIG_AML_CANVAS 1 // required for showing the logo during uboot |
| #define CONFIG_AML_VOUT 1 |
| #define CONFIG_AML_OSD 1 |
| #define CONFIG_OSD_SCALE_ENABLE 1 |
| #define CONFIG_CMD_BMP 1 |
| |
| #define CONFIG_AML_LCD 1 |
| #define CONFIG_AML_LCD_TABLET 1 |
| #define CONFIG_AML_LCD_EXTERN 1 |
| #define CONFIG_AML_LCD_EXTERN_MIPI_TV070WSM 1 |
| #define CONFIG_AML_LCD_EXTERN_MIPI_P070ACB 1 |
| #define CONFIG_AML_LCD_EXTERN_MIPI_TV070WSM_FT 1 |
| #define CONFIG_AML_LCD_EXTERN_MIPI_P070ACB_FT 1 |
| |
| /* USB |
| * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard |
| * Enable CONFIG_MUSB_UDD for Device functionalities. |
| */ |
| /* #define CONFIG_MUSB_UDC 1 */ |
| #define CONFIG_CMD_USB 1 |
| #if defined(CONFIG_CMD_USB) |
| #define CONFIG_GXL_XHCI_BASE 0xff500000 |
| #define CONFIG_GXL_USB_PHY2_BASE 0xffe09000 |
| #define CONFIG_GXL_USB_PHY3_BASE 0xffe09080 |
| #define CONFIG_USB_PHY_20 0xff636000 |
| #define CONFIG_USB_PHY_21 0xff63A000 |
| #define CONFIG_USB_STORAGE 1 |
| #define CONFIG_USB_XHCI 1 |
| #define CONFIG_USB_XHCI_AMLOGIC_V2 1 |
| #define CONFIG_USB_GPIO_PWR GPIOEE(GPIOH_6) |
| #define CONFIG_USB_GPIO_PWR_NAME "GPIOH_6" |
| //#define CONFIG_USB_XHCI_AMLOGIC_USB3_V2 1 |
| #endif //#if defined(CONFIG_CMD_USB) |
| |
| #define CONFIG_TXLX_USB 1 |
| #define CONFIG_USB_DEVICE_V2 1 |
| #define USB_PHY2_PLL_PARAMETER_1 0x09400414 |
| #define USB_PHY2_PLL_PARAMETER_2 0x927e0000 |
| #define USB_PHY2_PLL_PARAMETER_3 0xAC5F49E5 |
| |
| //UBOOT Facotry usb/sdcard burning config |
| #ifndef CONFIG_AML_DISABLE_UPDATE_MODE |
| #define CONFIG_AML_V2_FACTORY_BURN 1 //support facotry usb burning |
| #endif |
| #define CONFIG_AML_FACTORY_BURN_LOCAL_UPGRADE 1 //support factory sdcard burning |
| #define CONFIG_POWER_KEY_NOT_SUPPORTED_FOR_BURN 1 //There isn't power-key for factory sdcard burning |
| #define CONFIG_SD_BURNING_SUPPORT_UI 1 //Displaying upgrading progress bar when sdcard/udisk burning |
| |
| #define CONFIG_AML_SECURITY_KEY 1 |
| #define CONFIG_UNIFY_KEY_MANAGE 1 |
| |
| /* other devices */ |
| #define CONFIG_EFUSE 1 |
| #define CONFIG_SYS_I2C_AML 1 |
| #define CONFIG_SYS_I2C_AML_HAS_MASK 1 |
| #define CONFIG_SYS_I2C_SPEED 400000 |
| #define CONFIG_I2C_MULTI_BUS 1 |
| |
| /* commands */ |
| #define CONFIG_CMD_CACHE 1 |
| #define CONFIG_CMD_BOOTI 1 |
| #define CONFIG_CMD_EFUSE 1 |
| #define CONFIG_CMD_I2C 1 |
| #define CONFIG_CMD_MEMORY 1 |
| #define CONFIG_CMD_FAT 1 |
| #define CONFIG_CMD_GPIO 1 |
| #define CONFIG_CMD_RUN |
| #define CONFIG_CMD_REBOOT 1 |
| #define CONFIG_CMD_FACTORY_BOOT 1 |
| #define CONFIG_CMD_ECHO 1 |
| #define CONFIG_CMD_AUTOSCRIPT 1 |
| #define CONFIG_CMD_MISC 1 |
| |
| /*file system*/ |
| #define CONFIG_DOS_PARTITION 1 |
| #define CONFIG_EFI_PARTITION 1 |
| #define CONFIG_AML_PARTITION 1 |
| #define CONFIG_MMC 1 |
| #define CONFIG_FS_FAT 1 |
| #define CONFIG_FS_EXT4 1 |
| #define CONFIG_LZO 1 |
| |
| /* Cache Definitions */ |
| //#define CONFIG_SYS_DCACHE_OFF |
| //#define CONFIG_SYS_ICACHE_OFF |
| |
| /* other functions */ |
| #define CONFIG_NEED_BL301 1 |
| #define CONFIG_NEED_BL32 1 |
| #define CONFIG_FIP_IMG_SUPPORT 1 |
| #define CONFIG_BOOTDELAY -2 // autoboot with no delay and not check for abort |
| #define CONFIG_SYS_LONGHELP 1 |
| #define CONFIG_CMD_MISC 1 |
| #define CONFIG_CMD_ITEST 1 |
| #define CONFIG_CMD_CPU_TEMP 1 |
| #define CONFIG_SYS_MEM_TOP_HIDE 0x08000000 //hide 128MB for kernel reserve |
| #define CONFIG_CMD_LOADB 1 |
| |
| //#define CONFIG_MULTI_DTB 1 |
| |
| /* debug mode defines */ |
| //#define CONFIG_DEBUG_MODE 1 |
| #ifdef CONFIG_DEBUG_MODE |
| #define CONFIG_DDR_CLK_DEBUG 636 |
| #define CONFIG_CPU_CLK_DEBUG 600 |
| #endif |
| |
| //support secure boot |
| #define CONFIG_AML_SECURE_UBOOT 1 |
| |
| #if defined(CONFIG_AML_SECURE_UBOOT) |
| |
| //for SRAM size limitation just disable NAND |
| //as the socket board default has no NAND |
| //#undef CONFIG_AML_NAND |
| |
| //unify build for generate encrypted bootloader "u-boot.bin.encrypt" |
| #define CONFIG_AML_CRYPTO_UBOOT 1 |
| |
| //unify build for generate encrypted kernel image |
| //SRC : "board/amlogic/(board)/boot.img" |
| //DST : "fip/boot.img.encrypt" |
| //#define CONFIG_AML_CRYPTO_IMG 1 |
| |
| #endif //CONFIG_AML_SECURE_UBOOT |
| |
| #define CONFIG_SECURE_STORAGE 1 |
| |
| // Check size of boot image before load. See doc: |
| // https://docs.google.com/document/d/1YrW2yBzCbMrQfBR2n56aUPZPg_0waxveOH-E0NU07OM/edit?usp=sharing |
| #define CONFIG_IMG_SECURE_CHECK_SZ 0x3f00000 |
| |
| //build with uboot auto test |
| //#define CONFIG_AML_UBOOT_AUTO_TEST 1 |
| |
| //board customer ID |
| //#define CONFIG_CUSTOMER_ID (0x6472616F624C4D41) |
| |
| #if defined(CONFIG_CUSTOMER_ID) |
| #undef CONFIG_AML_CUSTOMER_ID |
| #define CONFIG_AML_CUSTOMER_ID CONFIG_CUSTOMER_ID |
| #endif |
| |
| #endif |
| |