blob: e95fdba59265a2c46e05a158395b95dfeee6c751 [file] [log] [blame]
/*
* board/amlogic/configs/gxl_p212_v1.h
*
* Copyright (C) 2015 Amlogic, Inc. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
*/
#ifndef __GXL_P212_V1_H__
#define __GXL_P212_V1_H__
#ifndef __SUSPEND_FIRMWARE__
#include <asm/arch/cpu.h>
#endif /* for compile problem of A53 and m3 */
#define CONFIG_SYS_GENERIC_BOARD 1
#ifndef __SUSPEND_FIRMWARE__
#ifndef CONFIG_AML_MESON
#warning "include warning"
#endif
#endif /* for compile problem of A53 and m3 */
/*
* platform power init config
*/
#define CONFIG_PLATFORM_POWER_INIT
#define CONFIG_VCCK_INIT_VOLTAGE 1120
#define CONFIG_VDDEE_INIT_VOLTAGE 1000 // voltage for power up
#define CONFIG_VDDEE_SLEEP_VOLTAGE 850 // voltage for suspend
/* configs for CEC */
#define CONFIG_CEC_OSD_NAME "Mbox"
#define CONFIG_CEC_WAKEUP
//#define CONFIG_BT_WAKEUP
#define CONFIG_INSTABOOT
/* configs for dtb in boot.img */
//#define DTB_BIND_KERNEL
/* SMP Definitinos */
#define CPU_RELEASE_ADDR secondary_boot_func
/* config saradc*/
#define CONFIG_CMD_SARADC 1
/*config irblaster*/
#define CONFIG_CMD_IRBLASTER 1
/* support ext4*/
#define CONFIG_CMD_EXT4 1
/* Bootloader Control Block function
That is used for recovery and the bootloader to talk to each other
*/
#define CONFIG_BOOTLOADER_CONTROL_BLOCK
/*a/b update */
#define CONFIG_CMD_BOOTCTOL_AVB
/* Serial config */
#define CONFIG_CONS_INDEX 2
#define CONFIG_BAUDRATE 115200
#define CONFIG_AML_MESON_SERIAL 1
#define CONFIG_SERIAL_MULTI 1
//Enable ir remote wake up for bl30
//#define CONFIG_IR_REMOTE
//#define CONFIG_AML_IRDETECT_EARLY
#define CONFIG_IR_REMOTE_POWER_UP_KEY_CNT 4
#define CONFIG_IR_REMOTE_USE_PROTOCOL 0 // 0:nec 1:duokan 2:Toshiba 3:rca 4:rcmm
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL1 0XE51AFB04 //amlogic tv ir --- power
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL2 0Xffffffff //amlogic tv ir --- ch+
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL3 0xffffffff //amlogic tv ir --- ch-
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL4 0xBA45BD02
#define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL5 0xffffffff
/* args/envs */
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_EXTRA_ENV_SETTINGS \
"firstboot=0\0"\
"upgrade_step=0\0"\
"jtag=apao\0"\
"loadaddr=1080000\0"\
"outputmode=1080p60hz\0" \
"hdmimode=1080p60hz\0" \
"cvbsmode=576cvbs\0" \
"display_width=1920\0" \
"display_height=1080\0" \
"display_bpp=16\0" \
"display_color_index=16\0" \
"display_layer=osd1\0" \
"display_color_fg=0xffff\0" \
"display_color_bg=0\0" \
"dtb_mem_addr=0x1000000\0" \
"fb_addr=0x3d800000\0" \
"fb_width=1920\0" \
"fb_height=1080\0" \
"usb_burning=update 1000\0" \
"fdt_high=0x20000000\0"\
"lock=10001000\0"\
"try_auto_burn=update 700 750;\0"\
"sdcburncfg=aml_sdc_burn.ini\0"\
"sdc_burning=sdc_burn ${sdcburncfg}\0"\
"wipe_data=successful\0"\
"wipe_cache=successful\0"\
"EnableSelinux=enforcing\0"\
"recovery_part=recovery\0"\
"recovery_offset=0\0"\
"cvbs_drv=0\0"\
"active_slot=_a\0"\
"page_trace=on\0"\
"boot_part=boot\0"\
"rpmb_state=0\0"\
"initargs="\
"rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 "\
"\0"\
"upgrade_check="\
"echo upgrade_step=${upgrade_step}; "\
"if itest ${upgrade_step} == 3; then "\
"run init_display; run storeargs; run update;"\
"else fi;"\
"\0"\
"storeargs="\
"setenv bootargs ${initargs} androidboot.selinux=${EnableSelinux} logo=${display_layer},loaded,${fb_addr},${outputmode} maxcpus=${maxcpus} vout=${outputmode},enable hdmimode=${hdmimode} cvbsmode=${cvbsmode} hdmitx=${cecconfig} cvbsdrv=${cvbs_drv} androidboot.firstboot=${firstboot} jtag=${jtag}; "\
"setenv bootargs ${bootargs} androidboot.veritymode=enforcing androidboot.hardware=amlogic;"\
"setenv bootargs ${bootargs} page_trace=${page_trace};" \
"setenv bootargs ${bootargs} androidboot.rpmb_state=${rpmb_state};"\
"run cmdline_keys;"\
"setenv bootargs ${bootargs} androidboot.slot_suffix=${active_slot};"\
"\0"\
"switch_bootmode="\
"get_rebootmode;"\
"if test ${reboot_mode} = factory_reset; then "\
"run recovery_from_flash;"\
"else if test ${reboot_mode} = update; then "\
"run update;"\
"else if test ${reboot_mode} = cold_boot; then "\
/*"run try_auto_burn; "*/\
"else if test ${reboot_mode} = fastboot; then "\
"fastboot;"\
"fi;fi;fi;fi;"\
"\0" \
"storeboot="\
"if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;"\
"run update;"\
"\0"\
"factory_reset_poweroff_protect="\
"echo wipe_data=${wipe_data}; echo wipe_cache=${wipe_cache};"\
"if test ${wipe_data} = failed; then "\
"run init_display; run storeargs;"\
"if mmcinfo; then "\
"run recovery_from_sdcard;"\
"fi;"\
"if usb start 0; then "\
"run recovery_from_udisk;"\
"fi;"\
"run recovery_from_flash;"\
"fi; "\
"if test ${wipe_cache} = failed; then "\
"run init_display; run storeargs;"\
"if mmcinfo; then "\
"run recovery_from_sdcard;"\
"fi;"\
"if usb start 0; then "\
"run recovery_from_udisk;"\
"fi;"\
"run recovery_from_flash;"\
"fi; \0" \
"update="\
/*first usb burning, second sdc_burn, third ext-sd autoscr/recovery, last udisk autoscr/recovery*/\
"run usb_burning; "\
"run sdc_burning; "\
"if mmcinfo; then "\
"run recovery_from_sdcard;"\
"fi;"\
"if usb start 0; then "\
"run recovery_from_udisk;"\
"fi;"\
"run recovery_from_flash;"\
"\0"\
"recovery_from_sdcard="\
"setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};"\
"if fatload mmc 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;"\
"if fatload mmc 0 ${loadaddr} recovery.img; then "\
"if fatload mmc 0 ${dtb_mem_addr} dtb.img; then echo sd dtb.img loaded; fi;"\
"wipeisb; "\
"bootm ${loadaddr};fi;"\
"\0"\
"recovery_from_udisk="\
"setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};"\
"if fatload usb 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;"\
"if fatload usb 0 ${loadaddr} recovery.img; then "\
"if fatload usb 0 ${dtb_mem_addr} dtb.img; then echo udisk dtb.img loaded; fi;"\
"wipeisb; "\
"bootm ${loadaddr};fi;"\
"\0"\
"recovery_from_flash="\
"setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};"\
"if itest ${upgrade_step} == 3; then "\
"if ext4load mmc 1:2 ${dtb_mem_addr} /recovery/dtb.img; then echo cache dtb.img loaded; fi;"\
"if ext4load mmc 1:2 ${loadaddr} /recovery/recovery.img; then echo cache recovery.img loaded; wipeisb; bootm ${loadaddr}; fi;"\
"else fi;"\
"if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then wipeisb; bootm ${loadaddr}; fi;"\
"\0"\
"init_display="\
"osd open;osd clear;imgread pic logo bootup $loadaddr;bmp display $bootup_offset;bmp scale"\
"\0"\
"cmdline_keys="\
"if keyman init 0x1234; then "\
"if keyman read usid ${loadaddr} str; then "\
"setenv bootargs ${bootargs} androidboot.serialno=${usid};"\
"setenv serial ${usid};"\
"else "\
"setenv bootargs ${bootargs} androidboot.serialno=1234567890;"\
"setenv serial 1234567890;"\
"fi;"\
"if keyman read mac ${loadaddr} str; then "\
"setenv bootargs ${bootargs} mac=${mac} androidboot.mac=${mac};"\
"fi;"\
"if keyman read deviceid ${loadaddr} str; then "\
"setenv bootargs ${bootargs} androidboot.deviceid=${deviceid};"\
"fi;"\
"fi;"\
"\0"\
"bcb_cmd="\
"get_valid_slot;"\
"\0"\
"upgrade_key="\
"if gpio input GPIOAO_2; then "\
"echo detect upgrade key; sleep 3;"\
"if gpio input GPIOAO_2; then run update; fi;"\
"fi;"\
"\0"\
#define CONFIG_PREBOOT \
"run bcb_cmd; "\
"run factory_reset_poweroff_protect;"\
"run upgrade_check;"\
"run init_display;"\
"run storeargs;"\
"run upgrade_key;" \
"run switch_bootmode;"
#define CONFIG_BOOTCOMMAND "run storeboot"
//#define CONFIG_ENV_IS_NOWHERE 1
#define CONFIG_ENV_SIZE (64*1024)
#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
#define CONFIG_ANDROID_BOOT_IMAGE 1
#define CONFIG_ANDROID_IMG 1
#define CONFIG_SYS_BOOTM_LEN (64<<20) /* Increase max gunzip size*/
/* cpu */
#define CONFIG_CPU_CLK 1200 //MHz. Range: 600-1800, should be multiple of 24
/* ddr */
#define CONFIG_DDR_SIZE 0 //MB //0 means ddr size auto-detect
#define CONFIG_DDR_CLK 912 //MHz, Range: 384-1200, should be multiple of 24
#define CONFIG_DDR4_CLK 1008 //MHz, for boards which use different ddr chip
/* DDR type setting
* CONFIG_DDR_TYPE_LPDDR3 : LPDDR3
* CONFIG_DDR_TYPE_DDR3 : DDR3
* CONFIG_DDR_TYPE_DDR4 : DDR4
* CONFIG_DDR_TYPE_AUTO : DDR3/DDR4 auto detect */
#define CONFIG_DDR_TYPE CONFIG_DDR_TYPE_AUTO
/* DDR channel setting, please refer hardware design.
* CONFIG_DDR0_RANK0 : DDR0 rank0
* CONFIG_DDR0_RANK01 : DDR0 rank0+1
* CONFIG_DDR0_16BIT : DDR0 16bit mode
* CONFIG_DDR_CHL_AUTO : auto detect RANK0 / RANK0+1 */
#define CONFIG_DDR_CHANNEL_SET CONFIG_DDR_CHL_AUTO
#define CONFIG_DDR_FULL_TEST 0 //1 for ddr full test
#define CONFIG_NR_DRAM_BANKS 1
/* ddr functions */
#define CONFIG_CMD_DDR_D2PLL 0 //0:disable, 1:enable. d2pll cmd
#define CONFIG_CMD_DDR_TEST 0 //0:disable, 1:enable. ddrtest cmd
#define CONFIG_DDR_LOW_POWER 0 //0:disable, 1:enable. ddr clk gate for lp
#define CONFIG_DDR_ZQ_PD 0 //0:disable, 1:enable. ddr zq power down
#define CONFIG_DDR_USE_EXT_VREF 0 //0:disable, 1:enable. ddr use external vref
#define CONFIG_DDR_FUNC_PRINT_WINDOW 0 //0:disable, 1:enable. print ddr training window
/* storage: emmc/nand/sd */
#define CONFIG_STORE_COMPATIBLE 1
/*
* storage
* |---------|---------|
* | |
* emmc<--Compatible-->nand
* |-------|-------|
* | |
* MTD<-Exclusive->NFTL
*/
/* swither for mtd nand which is for slc only. */
/* support for mtd */
//#define CONFIG_AML_MTD 1
/* support for nftl */
#define CONFIG_AML_NAND 1
#if defined(CONFIG_AML_NAND) && defined(CONFIG_AML_MTD)
#error CONFIG_AML_NAND/CONFIG_AML_MTD can not support at the sametime;
#endif
#ifdef CONFIG_AML_MTD
#define CONFIG_CMD_NAND 1
#define CONFIG_MTD_DEVICE y
/* mtd parts of ourown.*/
#define CONFIFG_AML_MTDPART 1
/* mtd parts by env default way.*/
/*
#define MTDIDS_NAME_STR "aml_nand.0"
#define MTDIDS_DEFAULT "nand1=" MTDIDS_NAME_STR
#define MTDPARTS_DEFAULT "mtdparts=" MTDIDS_NAME_STR ":" \
"3M@8192K(logo)," \
"10M(recovery)," \
"8M(kernel)," \
"40M(rootfs)," \
"-(data)"
*/
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_RBTREE
#define CONFIG_CMD_NAND_TORTURE 1
#define CONFIG_CMD_MTDPARTS 1
#define CONFIG_MTD_PARTITIONS 1
#define CONFIG_SYS_MAX_NAND_DEVICE 2
#define CONFIG_SYS_NAND_BASE_LIST {0}
#endif
/* endof CONFIG_AML_MTD */
#define CONFIG_AML_SD_EMMC 1
#ifdef CONFIG_AML_SD_EMMC
#define CONFIG_GENERIC_MMC 1
#define CONFIG_CMD_MMC 1
#define CONFIG_CMD_GPT 1
#define CONFIG_SYS_MMC_ENV_DEV 1
#define CONFIG_EMMC_DDR52_EN 0
#define CONFIG_EMMC_DDR52_CLK 35000000
/*
flash/erase operation region on boot1
in bytes, 2M by default
*/
//#define CONFIG_EMMC_BOOT1_TOUCH_REGION (0x200000)
#endif
/* storage macro checks */
#if defined(CONFIG_AML_MTD) && defined(CONFIG_AML_NAND)
#error mtd/nftl are mutually-exclusive, only 1 nand driver can be enabled.
#endif
/* env */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CMD_SAVEENV
/* env checks */
#if (defined(CONFIG_ENV_IS_IN_AMLNAND) || defined(CONFIG_ENV_IS_IN_MMC)) && defined(CONFIG_STORE_COMPATIBLE)
#error env in amlnand/mmc already be compatible;
#endif
#define CONFIG_PARTITIONS 1
#define CONFIG_SYS_NO_FLASH 1
/* vpu */
#define CONFIG_AML_VPU 1
#define CONFIG_VPU_CLK_LEVEL_DFT 7
/* DISPLAY & HDMITX */
#define CONFIG_AML_HDMITX20 1
#define CONFIG_AML_CANVAS 1
#define CONFIG_AML_VOUT 1
#define CONFIG_AML_OSD 1
#define CONFIG_OSD_SCALE_ENABLE 1
#define CONFIG_CMD_BMP 1
#if defined(CONFIG_AML_VOUT)
#define CONFIG_AML_CVBS 1
#endif
/* USB
* Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard
* Enable CONFIG_MUSB_UDD for Device functionalities.
*/
/* #define CONFIG_MUSB_UDC 1 */
#define CONFIG_CMD_USB 1
#if defined(CONFIG_CMD_USB)
#define CONFIG_GXL_XHCI_BASE 0xc9000000
#define CONFIG_GXL_USB_PHY2_BASE 0xd0078000
#define CONFIG_GXL_USB_PHY3_BASE 0xd0078080
#define CONFIG_USB_STORAGE 1
#define CONFIG_USB_XHCI 1
#define CONFIG_USB_XHCI_AMLOGIC_GXL 1
#endif //#if defined(CONFIG_CMD_USB)
//UBOOT fastboot config
#define CONFIG_CMD_FASTBOOT 1
#define CONFIG_FASTBOOT_FLASH_MMC_DEV 1
#ifdef CONFIG_AML_MTD
#define CONFIG_FASTBOOT_FLASH_NAND_DEV 1
#endif
#define CONFIG_FASTBOOT_FLASH 1
#define CONFIG_USB_GADGET 1
#define CONFIG_USBDOWNLOAD_GADGET 1
#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_FASTBOOT_MAX_DOWN_SIZE 0x8000000
#define CONFIG_DEVICE_PRODUCT "p212"
//UBOOT Facotry usb/sdcard burning config
#define CONFIG_AML_V2_FACTORY_BURN 1 //support facotry usb burning
#define CONFIG_AML_FACTORY_BURN_LOCAL_UPGRADE 1 //support factory sdcard burning
#define CONFIG_POWER_KEY_NOT_SUPPORTED_FOR_BURN 1 //There isn't power-key for factory sdcard burning
#define CONFIG_SD_BURNING_SUPPORT_UI 1 //Displaying upgrading progress bar when sdcard/udisk burning
#define CONFIG_AML_SECURITY_KEY 1
#ifndef DTB_BIND_KERNEL
#define CONFIG_UNIFY_KEY_MANAGE 1
#endif
/* net */
#define CONFIG_CMD_NET 1
#if defined(CONFIG_CMD_NET)
#define CONFIG_DESIGNWARE_ETH 1
#define CONFIG_PHYLIB 1
#define CONFIG_NET_MULTI 1
#define CONFIG_CMD_PING 1
#define CONFIG_CMD_DHCP 1
#define CONFIG_CMD_RARP 1
#define CONFIG_HOSTNAME arm_gxbb
#define CONFIG_RANDOM_ETHADDR 1 /* use random eth addr, or default */
#define CONFIG_ETHADDR 00:15:18:01:81:31 /* Ethernet address */
#define CONFIG_IPADDR 10.18.9.97 /* Our ip address */
#define CONFIG_GATEWAYIP 10.18.9.1 /* Our getway ip address */
#define CONFIG_SERVERIP 10.18.9.113 /* Tftp server ip address */
#define CONFIG_NETMASK 255.255.255.0
#endif /* (CONFIG_CMD_NET) */
/* other devices */
#define CONFIG_EFUSE 1
#define CONFIG_SYS_I2C_AML 1
#define CONFIG_SYS_I2C_SPEED 400000
/* commands */
#define CONFIG_CMD_CACHE 1
#define CONFIG_CMD_BOOTI 1
#define CONFIG_CMD_EFUSE 1
#define CONFIG_CMD_I2C 1
#define CONFIG_CMD_MEMORY 1
#define CONFIG_CMD_FAT 1
#define CONFIG_CMD_GPIO 1
#define CONFIG_CMD_RUN
#define CONFIG_CMD_REBOOT 1
#define CONFIG_CMD_ECHO 1
#define CONFIG_CMD_JTAG 1
#define CONFIG_CMD_AUTOSCRIPT 1
#define CONFIG_CMD_MISC 1
/*file system*/
#define CONFIG_DOS_PARTITION 1
#define CONFIG_EFI_PARTITION 1
#define CONFIG_AML_PARTITION 1
#define CONFIG_MMC 1
#define CONFIG_FS_FAT 1
#define CONFIG_FS_EXT4 1
#define CONFIG_LZO 1
/* Cache Definitions */
//#define CONFIG_SYS_DCACHE_OFF
//#define CONFIG_SYS_ICACHE_OFF
/* other functions */
#define CONFIG_NEED_BL301 1
#define CONFIG_NEED_BL32 1
#define CONFIG_CMD_RSVMEM 1
#define CONFIG_FIP_IMG_SUPPORT 1
#define CONFIG_BOOTDELAY 1 //delay 1s
#define CONFIG_SYS_LONGHELP 1
#define CONFIG_CMD_MISC 1
#define CONFIG_CMD_ITEST 1
#define CONFIG_CMD_CPU_TEMP 1
#define CONFIG_SYS_MEM_TOP_HIDE 0x08000000 //hide 128MB for kernel reserve
#define CONFIG_MULTI_DTB 1
#define CONFIG_CMD_CHIPID 1
/* debug mode defines */
//#define CONFIG_DEBUG_MODE 1
#ifdef CONFIG_DEBUG_MODE
#define CONFIG_DDR_CLK_DEBUG 636
#define CONFIG_CPU_CLK_DEBUG 600
#endif
//support secure boot
#define CONFIG_AML_SECURE_UBOOT 1
#if defined(CONFIG_AML_SECURE_UBOOT)
//for SRAM size limitation just disable NAND
//as the socket board default has no NAND
//#undef CONFIG_AML_NAND
//unify build for generate encrypted bootloader "u-boot.bin.encrypt"
#define CONFIG_AML_CRYPTO_UBOOT 1
//unify build for generate encrypted kernel image
//SRC : "board/amlogic/(board)/boot.img"
//DST : "fip/boot.img.encrypt"
//#define CONFIG_AML_CRYPTO_IMG 1
#endif //CONFIG_AML_SECURE_UBOOT
#define CONFIG_SECURE_STORAGE 1
//build with uboot auto test
//#define CONFIG_AML_UBOOT_AUTO_TEST 1
//board customer ID
//#define CONFIG_CUSTOMER_ID (0x6472616F624C4D41)
#if defined(CONFIG_CUSTOMER_ID)
#undef CONFIG_AML_CUSTOMER_ID
#define CONFIG_AML_CUSTOMER_ID CONFIG_CUSTOMER_ID
#endif
#define CONFIG_INTERNAL_PHY
#endif