| /* |
| * Configuation settings for the Renesas Solutions AP-325RXA board |
| * |
| * Copyright (C) 2008 Renesas Solutions Corp. |
| * Copyright (C) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __AP325RXA_H |
| #define __AP325RXA_H |
| |
| #undef DEBUG |
| #define CONFIG_CPU_SH7723 1 |
| #define CONFIG_AP325RXA 1 |
| |
| #define CONFIG_CMD_LOADB |
| #define CONFIG_CMD_LOADS |
| #define CONFIG_CMD_FLASH |
| #define CONFIG_CMD_MEMORY |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_SDRAM |
| #define CONFIG_CMD_SAVEENV |
| #define CONFIG_CMD_IDE |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_DOS_PARTITION |
| |
| #define CONFIG_BAUDRATE 38400 |
| #define CONFIG_BOOTDELAY 3 |
| #define CONFIG_BOOTARGS "console=ttySC2,38400" |
| |
| #define CONFIG_VERSION_VARIABLE |
| #undef CONFIG_SHOW_BOOT_PROGRESS |
| |
| /* SMC9118 */ |
| #define CONFIG_SMC911X 1 |
| #define CONFIG_SMC911X_32_BIT 1 |
| #define CONFIG_SMC911X_BASE 0xB6080000 |
| |
| /* MEMORY */ |
| #define AP325RXA_SDRAM_BASE (0x88000000) |
| #define AP325RXA_FLASH_BASE_1 (0xA0000000) |
| #define AP325RXA_FLASH_BANK_SIZE (128 * 1024 * 1024) |
| |
| #define CONFIG_SYS_TEXT_BASE 0x8FFC0000 |
| |
| /* undef to save memory */ |
| #define CONFIG_SYS_LONGHELP |
| /* Monitor Command Prompt */ |
| /* Buffer size for input from the Console */ |
| #define CONFIG_SYS_CBSIZE 256 |
| /* Buffer size for Console output */ |
| #define CONFIG_SYS_PBSIZE 256 |
| /* max args accepted for monitor commands */ |
| #define CONFIG_SYS_MAXARGS 16 |
| /* Buffer size for Boot Arguments passed to kernel */ |
| #define CONFIG_SYS_BARGSIZE 512 |
| /* List of legal baudrate settings for this board */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 38400 } |
| |
| /* SCIF */ |
| #define CONFIG_SCIF_CONSOLE 1 |
| #define CONFIG_SCIF_A 1 /* SH7723 has SCIF and SCIFA */ |
| #define CONFIG_CONS_SCIF5 1 |
| |
| /* Suppress display of console information at boot */ |
| #undef CONFIG_SYS_CONSOLE_INFO_QUIET |
| #undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE |
| #undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE |
| |
| #define CONFIG_SYS_MEMTEST_START (AP325RXA_SDRAM_BASE) |
| #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024)) |
| |
| /* Enable alternate, more extensive, memory test */ |
| #undef CONFIG_SYS_ALT_MEMTEST |
| /* Scratch address used by the alternate memory test */ |
| #undef CONFIG_SYS_MEMTEST_SCRATCH |
| |
| /* Enable temporary baudrate change while serial download */ |
| #undef CONFIG_SYS_LOADS_BAUD_CHANGE |
| |
| #define CONFIG_SYS_SDRAM_BASE (AP325RXA_SDRAM_BASE) |
| /* maybe more, but if so u-boot doesn't know about it... */ |
| #define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024) |
| /* default load address for scripts ?!? */ |
| #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024) |
| |
| /* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */ |
| #define CONFIG_SYS_MONITOR_BASE (AP325RXA_FLASH_BASE_1) |
| /* Monitor size */ |
| #define CONFIG_SYS_MONITOR_LEN (128 * 1024) |
| /* Size of DRAM reserved for malloc() use */ |
| #define CONFIG_SYS_MALLOC_LEN (256 * 1024) |
| #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) |
| |
| /* FLASH */ |
| #define CONFIG_FLASH_CFI_DRIVER 1 |
| #define CONFIG_SYS_FLASH_CFI |
| #undef CONFIG_SYS_FLASH_QUIET_TEST |
| /* print 'E' for empty sector on flinfo */ |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| /* Physical start address of Flash memory */ |
| #define CONFIG_SYS_FLASH_BASE (AP325RXA_FLASH_BASE_1) |
| /* Max number of sectors on each Flash chip */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 |
| |
| /* |
| * IDE support |
| */ |
| #define CONFIG_IDE_RESET 1 |
| #define CONFIG_SYS_PIO_MODE 1 |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 1 |
| #define CONFIG_SYS_ATA_BASE_ADDR 0xB4180000 |
| #define CONFIG_SYS_ATA_STRIDE 2 /* 1bit shift */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x200 /* data reg offset */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0x200 /* reg offset */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x210 /* alternate register offset */ |
| #define CONFIG_IDE_SWAP_IO |
| |
| /* if you use all NOR Flash , you change dip-switch. Please see Manual. */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE + (0 * AP325RXA_FLASH_BANK_SIZE)} |
| |
| /* Timeout for Flash erase operations (in ms) */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) |
| /* Timeout for Flash write operations (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) |
| /* Timeout for Flash set sector lock bit operations (in ms) */ |
| #define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) |
| /* Timeout for Flash clear lock bit operations (in ms) */ |
| #define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) |
| |
| /* |
| * Use hardware flash sectors protection instead |
| * of U-Boot software protection |
| */ |
| #undef CONFIG_SYS_FLASH_PROTECTION |
| #undef CONFIG_SYS_DIRECT_FLASH_TFTP |
| |
| /* ENV setting */ |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_OVERWRITE 1 |
| #define CONFIG_ENV_SECT_SIZE (128 * 1024) |
| #define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) |
| /* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ |
| #define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) |
| |
| /* Board Clock */ |
| #define CONFIG_SYS_CLK_FREQ 33333333 |
| #define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ |
| #define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ |
| #define CONFIG_SYS_TMU_CLK_DIV (4) /* 4 (default), 16, 64, 256 or 1024 */ |
| |
| #endif /* __AP325RXA_H */ |
