blob: 949b3dadb385faec51c7e2af0d8eeb93897d7e8e [file] [log] [blame]
/*
* (C) Copyright 2013 Keymile AG
* Valentin Longchamp <valentin.longchamp@keymile.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _CONFIG_KMP204X_H
#define _CONFIG_KMP204X_H
#define CONFIG_PHYS_64BIT
#define CONFIG_PPC_P2041
#define CONFIG_SYS_TEXT_BASE 0xfff40000
#define CONFIG_KM_DEF_NETDEV "netdev=eth0\0"
/* an additionnal option is required for UBI as subpage access is
* supported in u-boot */
#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048"
#define CONFIG_NAND_ECC_BCH
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO
/* common KM defines */
#include "keymile-common.h"
#define CONFIG_SYS_RAMBOOT
#define CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
/* High Level Configuration Options */
#define CONFIG_BOOKE
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_E500MC /* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
#define CONFIG_MP /* support multiple processors */
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
#define CONFIG_PCI /* Enable PCI/PCIE */
#define CONFIG_PCIE1 /* PCIE controler 1 */
#define CONFIG_PCIE3 /* PCIE controler 3 */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_SYS_DPAA_RMAN /* RMan */
#define CONFIG_FSL_LAW /* Use common FSL init code */
/* Environment in SPI Flash */
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 20000000
#define CONFIG_ENV_SPI_MODE 0
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */
#define CONFIG_ENV_SIZE 0x004000 /* 16K env */
#define CONFIG_ENV_SECT_SIZE 0x010000
#define CONFIG_ENV_OFFSET_REDUND 0x110000
#define CONFIG_ENV_TOTAL_SIZE 0x020000
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(unsigned long dummy);
#endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BACKSIDE_L2_CACHE
#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */
/*
* Config the L3 Cache as L3 SRAM
*/
#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \
CONFIG_RAMBOOT_TEXT_BASE)
#define CONFIG_SYS_L3_SIZE (1024 << 10)
#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
/*
* DDR Setup
*/
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x54
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
/******************************************************************************
* (PRAM usage)
* ... -------------------------------------------------------
* ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
* ... |<------------------- pram -------------------------->|
* ... -------------------------------------------------------
* @END_OF_RAM:
* @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
* @CONFIG_KM_PHRAM: address for /var
* @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
* @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
*/
/* size of rootfs in RAM */
#define CONFIG_KM_ROOTFSSIZE 0x0
/* pseudo-non volatile RAM [hex] */
#define CONFIG_KM_PNVRAM 0x80000
/* physical RAM MTD size [hex] */
#define CONFIG_KM_PHRAM 0x100000
/* reserved pram area at the end of memory [hex]
* u-boot reserves some memory for the MP boot page */
#define CONFIG_KM_RESERVED_PRAM 0x1000
/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
* is not valid yet, which is the case for when u-boot copies itself to RAM */
#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10)
#define CONFIG_KM_CRAMFS_ADDR 0x2000000
#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */
#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */
/*
* Local Bus Definitions
*/
/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2)
/* Nand Flash */
#define CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_NAND_BASE 0xffa00000
#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_BCH
/* NAND flash config */
#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| BR_PS_8 /* Port Size = 8 bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
| OR_FCM_BCTLD /* LBCTL not ass */ \
| OR_FCM_SCY_1 /* 1 clk wait cycle */ \
| OR_FCM_RST /* 1 clk read setup */ \
| OR_FCM_PGS /* Large page size */ \
| OR_FCM_CST) /* 0.25 command setup */
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
/* QRIO FPGA */
#define CONFIG_SYS_QRIO_BASE 0xfb000000
#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull
#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
| BR_PS_8 /* Port Size 8 bits */ \
| BR_DECC_OFF /* no error corr */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \
| OR_GPCM_BCTLD /* no LCTL assert */ \
| OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
| OR_GPCM_TRLX /* relaxed tmgs */ \
| OR_GPCM_EAD) /* extra bus clk cycles */
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
/* bootcounter in QRIO */
#define CONFIG_BOOTCOUNT_LIMIT
#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_QRIO_BASE + 0x20)
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
#define CONFIG_MISC_INIT_F
#define CONFIG_MISC_INIT_R
#define CONFIG_LAST_STAGE_INIT
#define CONFIG_HWCONFIG
/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
#define CONFIG_KM_CONSOLE_TTY "ttyS0"
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS
/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_INIT_BOARD
#define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */
#define CONFIG_SYS_NUM_I2C_BUSES 3
#define CONFIG_SYS_I2C_MAX_HOPS 1
#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
{0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
}
#ifndef __ASSEMBLY__
void set_sda(int state);
void set_scl(int state);
int get_sda(void);
int get_scl(void);
#endif
#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/
/*
* eSPI - Enhanced SPI
*/
#define CONFIG_FSL_ESPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_SPI_FLASH_SPANSION
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE 0
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
/* Qman/Bman */
#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
#define CONFIG_SYS_BMAN_NUM_PORTALS 10
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
CONFIG_SYS_BMAN_CENA_SIZE)
#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_QMAN_NUM_PORTALS 10
#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
CONFIG_SYS_QMAN_CENA_SIZE)
#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
/* Default address of microcode for the Linux Fman driver
* env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
* ucode is stored after env, so we got 0x120000.
*/
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
#define CONFIG_SYS_FMAN_FW_ADDR 0x120000
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#define CONFIG_FMAN_ENET
#define CONFIG_PHYLIB_10G
#define CONFIG_PHY_MARVELL /* there is a marvell phy */
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_E1000
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
/* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */
#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11
#define CONFIG_SYS_TBIPA_VALUE 8
#define CONFIG_PHYLIB /* recommended PHY management */
#define CONFIG_ETHPRIME "FM1@DTSEC5"
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
/*
* Environment
*/
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
* Hardware Watchdog
*/
#define CONFIG_WATCHDOG /* enable CPU watchdog */
#define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */
#define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */
/*
* additionnal command line configuration.
*/
#define CONFIG_CMD_PCI
#define CONFIG_CMD_NET
#define CONFIG_CMD_ERRATA
/* we don't need flash support */
#define CONFIG_SYS_NO_FLASH
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_FLASH
#undef CONFIG_FLASH_CFI_MTD
#undef CONFIG_JFFS2_CMDLINE
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
#define __USB_PHY_TYPE utmi
/*
* Environment Configuration
*/
#define CONFIG_ENV_OVERWRITE
#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
#define CONFIG_KM_DEF_ENV "km-common=empty\0"
#endif
#ifndef MTDIDS_DEFAULT
# define MTDIDS_DEFAULT "nand0=fsl_elbc_nand"
#endif /* MTDIDS_DEFAULT */
#ifndef MTDPARTS_DEFAULT
# define MTDPARTS_DEFAULT "mtdparts=" \
"fsl_elbc_nand:" \
"-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"
#endif /* MTDPARTS_DEFAULT */
/* architecture specific default bootargs */
#define CONFIG_KM_DEF_BOOT_ARGS_CPU ""
/* FIXME: FDT_ADDR is unspecified */
#define CONFIG_KM_DEF_ENV_CPU \
"boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \
"cramfsloadfdt=" \
"cramfsload ${fdt_addr_r} " \
"fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \
"fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \
"u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0" \
"update=" \
"sf probe 0;sf erase 0 +${filesize};" \
"sf write ${load_addr_r} 0 ${filesize};\0" \
"set_fdthigh=true\0" \
""
#define CONFIG_HW_ENV_SETTINGS \
"hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \
"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
"usb_dr_mode=host\0"
#define CONFIG_KM_NEW_ENV \
"newenv=sf probe 0;" \
"sf erase " __stringify(CONFIG_ENV_OFFSET) " " \
__stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
#ifndef CONFIG_KM_DEF_ARCH
#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_KM_DEF_ENV \
CONFIG_KM_DEF_ARCH \
CONFIG_KM_NEW_ENV \
CONFIG_HW_ENV_SETTINGS \
"EEprom_ivm=pca9547:70:9\0" \
""
#endif /* _CONFIG_KMP204X_H */