include/configs/uniphier.h - u-boot - Git at Google

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright (C) 2012-2015 Panasonic Corporation
  * Copyright (C) 2015-2016 Socionext Inc.
  *   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
  */

 /* U-Boot - Common settings for UniPhier Family */

 #ifndef __CONFIG_UNIPHIER_COMMON_H__
 #define __CONFIG_UNIPHIER_COMMON_H__

 #define CONFIG_ARMV7_PSCI_1_0

 /*-----------------------------------------------------------------------
  * MMU and Cache Setting
  *----------------------------------------------------------------------*/

 /* Comment out the following to enable L1 cache */
 /* #define CONFIG_SYS_ICACHE_OFF */
 /* #define CONFIG_SYS_DCACHE_OFF */

 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)

 #define CONFIG_TIMESTAMP

 /* FLASH related */
 #define CONFIG_MTD_DEVICE

 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI

 #define CONFIG_SYS_MAX_FLASH_SECT	256
 #define CONFIG_SYS_MONITOR_BASE		0
 #define CONFIG_SYS_MONITOR_LEN		0x00090000	/* 576KB */
 #define CONFIG_SYS_FLASH_BASE		0

 /*
  * flash_toggle does not work for our support card.
  * We need to use flash_status_poll.
  */
 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL

 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1

 /* serial console configuration */

 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)

 #define CONFIG_ENV_OFFSET			0x100000
 #define CONFIG_ENV_SIZE				0x2000
 /* #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */

 #define CONFIG_SYS_MMC_ENV_DEV		0
 #define CONFIG_SYS_MMC_ENV_PART		1

 #if !defined(CONFIG_ARM64)
 /* Time clock 1MHz */
 #define CONFIG_SYS_TIMER_RATE			1000000
 #endif

 #define CONFIG_SYS_MAX_NAND_DEVICE			1
 #define CONFIG_SYS_NAND_ONFI_DETECTION
 #define CONFIG_SYS_NAND_REGS_BASE			0x68100000
 #define CONFIG_SYS_NAND_DATA_BASE			0x68000000
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS			0

 /* SD/MMC */
 #define CONFIG_SUPPORT_EMMC_BOOT

 /* memtest works on */
 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x01000000)

 /*
  * Network Configuration
  */
 #define CONFIG_SERVERIP			192.168.11.1
 #define CONFIG_IPADDR			192.168.11.10
 #define CONFIG_GATEWAYIP		192.168.11.1
 #define CONFIG_NETMASK			255.255.255.0

 #define CONFIG_LOADADDR			0x85000000
 #define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
 #define CONFIG_SYS_BOOTM_LEN		(32 << 20)

 #if defined(CONFIG_ARM64)
 /* ARM Trusted Firmware */
 #define BOOT_IMAGES \
 	"second_image=unph_bl.bin\0" \
 	"third_image=fip.bin\0"
 #else
 #define BOOT_IMAGES \
 	"second_image=u-boot-spl.bin\0" \
 	"third_image=u-boot.bin\0"
 #endif

 #define CONFIG_BOOTCOMMAND		"run $bootmode"

 #define CONFIG_ROOTPATH			"/nfs/root/path"
 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv bootargs $bootargs root=/dev/nfs rw "			\
 	"nfsroot=$serverip:$rootpath "					\
 	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
 		"run __nfsboot"

 #ifdef CONFIG_FIT
 #define CONFIG_BOOTFILE			"fitImage"
 #define LINUXBOOT_ENV_SETTINGS \
 	"fit_addr=0x00100000\0" \
 	"fit_addr_r=0x85100000\0" \
 	"fit_size=0x00f00000\0" \
 	"norboot=setexpr fit_addr $nor_base + $fit_addr &&" \
 		"bootm $fit_addr\0" \
 	"nandboot=nand read $fit_addr_r $fit_addr $fit_size &&" \
 		"bootm $fit_addr_r\0" \
 	"tftpboot=tftpboot $fit_addr_r $bootfile &&" \
 		"bootm $fit_addr_r\0" \
 	"__nfsboot=run tftpboot\0"
 #else
 #ifdef CONFIG_ARM64
 #define CONFIG_BOOTFILE			"Image.gz"
 #define LINUXBOOT_CMD			"booti"
 #define KERNEL_ADDR_LOAD		"kernel_addr_load=0x85200000\0"
 #define KERNEL_ADDR_R			"kernel_addr_r=0x82080000\0"
 #else
 #define CONFIG_BOOTFILE			"zImage"
 #define LINUXBOOT_CMD			"bootz"
 #define KERNEL_ADDR_LOAD		"kernel_addr_load=0x80208000\0"
 #define KERNEL_ADDR_R			"kernel_addr_r=0x80208000\0"
 #endif
 #define LINUXBOOT_ENV_SETTINGS \
 	"fdt_addr=0x00100000\0" \
 	"fdt_addr_r=0x85100000\0" \
 	"fdt_size=0x00008000\0" \
 	"kernel_addr=0x00200000\0" \
 	KERNEL_ADDR_LOAD \
 	KERNEL_ADDR_R \
 	"kernel_size=0x00e00000\0" \
 	"ramdisk_addr=0x01000000\0" \
 	"ramdisk_addr_r=0x86000000\0" \
 	"ramdisk_size=0x00800000\0" \
 	"ramdisk_file=rootfs.cpio.uboot\0" \
 	"boot_common=setexpr bootm_low $kernel_addr_r '&' fe000000 && " \
 		"if test $kernel_addr_load = $kernel_addr_r; then " \
 			"true; " \
 		"else " \
 			"unzip $kernel_addr_load $kernel_addr_r; " \
 		"fi && " \
 		LINUXBOOT_CMD " $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0" \
 	"norboot=setexpr kernel_addr_nor $nor_base + $kernel_addr && " \
 		"setexpr kernel_size_div4 $kernel_size / 4 && " \
 		"cp $kernel_addr_nor $kernel_addr_load $kernel_size_div4 && " \
 		"setexpr ramdisk_addr_nor $nor_base + $ramdisk_addr && " \
 		"setexpr ramdisk_size_div4 $ramdisk_size / 4 && " \
 		"cp $ramdisk_addr_nor $ramdisk_addr_r $ramdisk_size_div4 && " \
 		"setexpr fdt_addr_nor $nor_base + $fdt_addr && " \
 		"setexpr fdt_size_div4 $fdt_size / 4 && " \
 		"cp $fdt_addr_nor $fdt_addr_r $fdt_size_div4 && " \
 		"run boot_common\0" \
 	"nandboot=nand read $kernel_addr_load $kernel_addr $kernel_size && " \
 		"nand read $ramdisk_addr_r $ramdisk_addr $ramdisk_size &&" \
 		"nand read $fdt_addr_r $fdt_addr $fdt_size &&" \
 		"run boot_common\0" \
 	"tftpboot=tftpboot $kernel_addr_load $bootfile && " \
 		"tftpboot $ramdisk_addr_r $ramdisk_file &&" \
 		"tftpboot $fdt_addr_r $fdt_file &&" \
 		"run boot_common\0" \
 	"__nfsboot=tftpboot $kernel_addr_load $bootfile && " \
 		"tftpboot $fdt_addr_r $fdt_file &&" \
 		"setenv ramdisk_addr_r - &&" \
 		"run boot_common\0"
 #endif

 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"netdev=eth0\0"						\
 	"initrd_high=0xffffffffffffffff\0"			\
 	"nor_base=0x42000000\0"					\
 	"sramupdate=setexpr tmp_addr $nor_base + 0x50000 &&"	\
 		"tftpboot $tmp_addr $second_image && " \
 		"setexpr tmp_addr $nor_base + 0x70000 && " \
 		"tftpboot $tmp_addr $third_image\0" \
 	"emmcupdate=mmcsetn &&"					\
 		"mmc dev $mmc_first_dev &&"			\
 		"mmc partconf $mmc_first_dev 0 1 1 &&"		\
 		"tftpboot $second_image && " \
 		"mmc write $loadaddr 0 100 && " \
 		"tftpboot $third_image && " \
 		"mmc write $loadaddr 100 f00\0" \
 	"nandupdate=nand erase 0 0x00100000 &&"			\
 		"tftpboot $second_image && " \
 		"nand write $loadaddr 0 0x00020000 && " \
 		"tftpboot $third_image && " \
 		"nand write $loadaddr 0x00020000 0x001e0000\0" \
 	"usbupdate=usb start &&" \
 		"tftpboot $second_image && " \
 		"usb write $loadaddr 0 100 && " \
 		"tftpboot $third_image && " \
 		"usb write $loadaddr 100 f00\0" \
 	BOOT_IMAGES \
 	LINUXBOOT_ENV_SETTINGS

 #define CONFIG_SYS_BOOTMAPSZ			0x20000000

 #define CONFIG_SYS_SDRAM_BASE		0x80000000
 #define CONFIG_NR_DRAM_BANKS		3

 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE)

 /* only for SPL */
 #if defined(CONFIG_ARCH_UNIPHIER_LD4) || \
 	defined(CONFIG_ARCH_UNIPHIER_SLD8)
 #define CONFIG_SPL_TEXT_BASE		0x00040000
 #else
 #define CONFIG_SPL_TEXT_BASE		0x00100000
 #endif

 #define CONFIG_SPL_STACK		(0x00200000)

 #define CONFIG_SYS_NAND_U_BOOT_OFFS		0x20000

 /* subtract sizeof(struct image_header) */
 #define CONFIG_SYS_UBOOT_BASE			(0x70000 - 0x40)

 #define CONFIG_SPL_TARGET			"u-boot-with-spl.bin"
 #define CONFIG_SPL_MAX_FOOTPRINT		0x10000
 #define CONFIG_SPL_MAX_SIZE			0x10000
 #define CONFIG_SPL_BSS_MAX_SIZE			0x2000

 #define CONFIG_SPL_PAD_TO			0x20000

 #endif /* __CONFIG_UNIPHIER_COMMON_H__ */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright (C) 2012-2015 Panasonic Corporation
	* Copyright (C) 2015-2016 Socionext Inc.
	* Author: Masahiro Yamada <yamada.masahiro@socionext.com>
	*/

	/* U-Boot - Common settings for UniPhier Family */

	#ifndef __CONFIG_UNIPHIER_COMMON_H__
	#define __CONFIG_UNIPHIER_COMMON_H__

	#define CONFIG_ARMV7_PSCI_1_0

	/*-----------------------------------------------------------------------
	* MMU and Cache Setting
	----------------------------------------------------------------------/

	/* Comment out the following to enable L1 cache */
	/* #define CONFIG_SYS_ICACHE_OFF */
	/* #define CONFIG_SYS_DCACHE_OFF */

	#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)

	#define CONFIG_TIMESTAMP

	/* FLASH related */
	#define CONFIG_MTD_DEVICE

	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI

	#define CONFIG_SYS_MAX_FLASH_SECT 256
	#define CONFIG_SYS_MONITOR_BASE 0
	#define CONFIG_SYS_MONITOR_LEN 0x00090000 /* 576KB */
	#define CONFIG_SYS_FLASH_BASE 0

	/*
	* flash_toggle does not work for our support card.
	* We need to use flash_status_poll.
	*/
	#define CONFIG_SYS_CFI_FLASH_STATUS_POLL

	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

	#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1

	/* serial console configuration */

	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)

	#define CONFIG_ENV_OFFSET 0x100000
	#define CONFIG_ENV_SIZE 0x2000
	/* #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */

	#define CONFIG_SYS_MMC_ENV_DEV 0
	#define CONFIG_SYS_MMC_ENV_PART 1

	#if !defined(CONFIG_ARM64)
	/* Time clock 1MHz */
	#define CONFIG_SYS_TIMER_RATE 1000000
	#endif

	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_ONFI_DETECTION
	#define CONFIG_SYS_NAND_REGS_BASE 0x68100000
	#define CONFIG_SYS_NAND_DATA_BASE 0x68000000
	#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0

	/* SD/MMC */
	#define CONFIG_SUPPORT_EMMC_BOOT

	/* memtest works on */
	#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
	#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01000000)

	/*
	* Network Configuration
	*/
	#define CONFIG_SERVERIP 192.168.11.1
	#define CONFIG_IPADDR 192.168.11.10
	#define CONFIG_GATEWAYIP 192.168.11.1
	#define CONFIG_NETMASK 255.255.255.0

	#define CONFIG_LOADADDR 0x85000000
	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
	#define CONFIG_SYS_BOOTM_LEN (32 << 20)

	#if defined(CONFIG_ARM64)
	/* ARM Trusted Firmware */
	#define BOOT_IMAGES \
	"second_image=unph_bl.bin\0" \
	"third_image=fip.bin\0"
	#else
	#define BOOT_IMAGES \
	"second_image=u-boot-spl.bin\0" \
	"third_image=u-boot.bin\0"
	#endif

	#define CONFIG_BOOTCOMMAND "run $bootmode"

	#define CONFIG_ROOTPATH "/nfs/root/path"
	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs $bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
	"run __nfsboot"

	#ifdef CONFIG_FIT
	#define CONFIG_BOOTFILE "fitImage"
	#define LINUXBOOT_ENV_SETTINGS \
	"fit_addr=0x00100000\0" \
	"fit_addr_r=0x85100000\0" \
	"fit_size=0x00f00000\0" \
	"norboot=setexpr fit_addr $nor_base + $fit_addr &&" \
	"bootm $fit_addr\0" \
	"nandboot=nand read $fit_addr_r $fit_addr $fit_size &&" \
	"bootm $fit_addr_r\0" \
	"tftpboot=tftpboot $fit_addr_r $bootfile &&" \
	"bootm $fit_addr_r\0" \
	"__nfsboot=run tftpboot\0"
	#else
	#ifdef CONFIG_ARM64
	#define CONFIG_BOOTFILE "Image.gz"
	#define LINUXBOOT_CMD "booti"
	#define KERNEL_ADDR_LOAD "kernel_addr_load=0x85200000\0"
	#define KERNEL_ADDR_R "kernel_addr_r=0x82080000\0"
	#else
	#define CONFIG_BOOTFILE "zImage"
	#define LINUXBOOT_CMD "bootz"
	#define KERNEL_ADDR_LOAD "kernel_addr_load=0x80208000\0"
	#define KERNEL_ADDR_R "kernel_addr_r=0x80208000\0"
	#endif
	#define LINUXBOOT_ENV_SETTINGS \
	"fdt_addr=0x00100000\0" \
	"fdt_addr_r=0x85100000\0" \
	"fdt_size=0x00008000\0" \
	"kernel_addr=0x00200000\0" \
	KERNEL_ADDR_LOAD \
	KERNEL_ADDR_R \
	"kernel_size=0x00e00000\0" \
	"ramdisk_addr=0x01000000\0" \
	"ramdisk_addr_r=0x86000000\0" \
	"ramdisk_size=0x00800000\0" \
	"ramdisk_file=rootfs.cpio.uboot\0" \
	"boot_common=setexpr bootm_low $kernel_addr_r '&' fe000000 && " \
	"if test $kernel_addr_load = $kernel_addr_r; then " \
	"true; " \
	"else " \
	"unzip $kernel_addr_load $kernel_addr_r; " \
	"fi && " \
	LINUXBOOT_CMD " $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0" \
	"norboot=setexpr kernel_addr_nor $nor_base + $kernel_addr && " \
	"setexpr kernel_size_div4 $kernel_size / 4 && " \
	"cp $kernel_addr_nor $kernel_addr_load $kernel_size_div4 && " \
	"setexpr ramdisk_addr_nor $nor_base + $ramdisk_addr && " \
	"setexpr ramdisk_size_div4 $ramdisk_size / 4 && " \
	"cp $ramdisk_addr_nor $ramdisk_addr_r $ramdisk_size_div4 && " \
	"setexpr fdt_addr_nor $nor_base + $fdt_addr && " \
	"setexpr fdt_size_div4 $fdt_size / 4 && " \
	"cp $fdt_addr_nor $fdt_addr_r $fdt_size_div4 && " \
	"run boot_common\0" \
	"nandboot=nand read $kernel_addr_load $kernel_addr $kernel_size && " \
	"nand read $ramdisk_addr_r $ramdisk_addr $ramdisk_size &&" \
	"nand read $fdt_addr_r $fdt_addr $fdt_size &&" \
	"run boot_common\0" \
	"tftpboot=tftpboot $kernel_addr_load $bootfile && " \
	"tftpboot $ramdisk_addr_r $ramdisk_file &&" \
	"tftpboot $fdt_addr_r $fdt_file &&" \
	"run boot_common\0" \
	"__nfsboot=tftpboot $kernel_addr_load $bootfile && " \
	"tftpboot $fdt_addr_r $fdt_file &&" \
	"setenv ramdisk_addr_r - &&" \
	"run boot_common\0"
	#endif

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"nor_base=0x42000000\0" \
	"sramupdate=setexpr tmp_addr $nor_base + 0x50000 &&" \
	"tftpboot $tmp_addr $second_image && " \
	"setexpr tmp_addr $nor_base + 0x70000 && " \
	"tftpboot $tmp_addr $third_image\0" \
	"emmcupdate=mmcsetn &&" \
	"mmc dev $mmc_first_dev &&" \
	"mmc partconf $mmc_first_dev 0 1 1 &&" \
	"tftpboot $second_image && " \
	"mmc write $loadaddr 0 100 && " \
	"tftpboot $third_image && " \
	"mmc write $loadaddr 100 f00\0" \
	"nandupdate=nand erase 0 0x00100000 &&" \
	"tftpboot $second_image && " \
	"nand write $loadaddr 0 0x00020000 && " \
	"tftpboot $third_image && " \
	"nand write $loadaddr 0x00020000 0x001e0000\0" \
	"usbupdate=usb start &&" \
	"tftpboot $second_image && " \
	"usb write $loadaddr 0 100 && " \
	"tftpboot $third_image && " \
	"usb write $loadaddr 100 f00\0" \
	BOOT_IMAGES \
	LINUXBOOT_ENV_SETTINGS

	#define CONFIG_SYS_BOOTMAPSZ 0x20000000

	#define CONFIG_SYS_SDRAM_BASE 0x80000000
	#define CONFIG_NR_DRAM_BANKS 3

	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE)

	/* only for SPL */
	#if defined(CONFIG_ARCH_UNIPHIER_LD4) \|\| \
	defined(CONFIG_ARCH_UNIPHIER_SLD8)
	#define CONFIG_SPL_TEXT_BASE 0x00040000
	#else
	#define CONFIG_SPL_TEXT_BASE 0x00100000
	#endif

	#define CONFIG_SPL_STACK (0x00200000)

	#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000

	/* subtract sizeof(struct image_header) */
	#define CONFIG_SYS_UBOOT_BASE (0x70000 - 0x40)

	#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
	#define CONFIG_SPL_MAX_FOOTPRINT 0x10000
	#define CONFIG_SPL_MAX_SIZE 0x10000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x2000

	#define CONFIG_SPL_PAD_TO 0x20000

	#endif /* __CONFIG_UNIPHIER_COMMON_H__ */