| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright (C) 2009, STMicroelectronics - All Rights Reserved |
| * Author(s): Vipin Kumar, <vipin.kumar@st.com> for STMicroelectronics. |
| * |
| * Copyright (C) 2012, 2015 Stefan Roese <sr@denx.de> |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| #define CONFIG_SPEAR600 /* SPEAr600 SoC */ |
| #define CONFIG_X600 /* on X600 board */ |
| |
| #include <asm/arch/hardware.h> |
| |
| /* Timer, HZ specific defines */ |
| #define CONFIG_SYS_HZ_CLOCK 8300000 |
| |
| #define CONFIG_SYS_FLASH_BASE 0xf8000000 |
| /* Reserve 8KiB for SPL */ |
| #define CONFIG_SPL_PAD_TO 8192 /* decimal for 'dd' */ |
| #define CONFIG_SYS_SPL_LEN CONFIG_SPL_PAD_TO |
| #define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + \ |
| CONFIG_SYS_SPL_LEN) |
| #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_MONITOR_LEN 0x60000 |
| |
| /* Serial Configuration (PL011) */ |
| #define CONFIG_SYS_SERIAL0 0xD0000000 |
| #define CONFIG_SYS_SERIAL1 0xD0080000 |
| #define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, \ |
| (void *)CONFIG_SYS_SERIAL1 } |
| #define CONFIG_PL011_CLOCK (48 * 1000 * 1000) |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, \ |
| 57600, 115200 } |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE |
| |
| /* NOR FLASH config options */ |
| #define CONFIG_ST_SMI |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| #define CONFIG_SYS_FLASH_BANK_SIZE 0x01000000 |
| #define CONFIG_SYS_FLASH_ADDR_BASE { CONFIG_SYS_FLASH_BASE } |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_ERASE_TOUT (3 * CONFIG_SYS_HZ) |
| #define CONFIG_SYS_FLASH_WRITE_TOUT (3 * CONFIG_SYS_HZ) |
| |
| /* NAND FLASH config options */ |
| #define CONFIG_NAND_FSMC |
| #define CONFIG_SYS_NAND_SELF_INIT |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE CONFIG_FSMC_NAND_BASE |
| #define CONFIG_MTD_ECC_SOFT |
| #define CONFIG_SYS_FSMC_NAND_8BIT |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| #define CONFIG_NAND_ECC_BCH |
| |
| /* UBI/UBI config options */ |
| #define CONFIG_MTD_DEVICE |
| #define CONFIG_MTD_PARTITIONS |
| |
| /* Ethernet config options */ |
| #define CONFIG_MII |
| #define CONFIG_PHY_RESET_DELAY 10000 /* in usec */ |
| |
| #define CONFIG_SPEAR_GPIO |
| |
| /* I2C config options */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_BASE 0xD0200000 |
| #define CONFIG_SYS_I2C_SPEED 400000 |
| #define CONFIG_SYS_I2C_SLAVE 0x02 |
| #define CONFIG_I2C_CHIPADDRESS 0x50 |
| |
| #define CONFIG_RTC_M41T62 1 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| |
| /* FPGA config options */ |
| #define CONFIG_FPGA_COUNT 1 |
| |
| /* USB EHCI options */ |
| #define CONFIG_USB_EHCI_SPEAR |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 |
| |
| /* |
| * U-Boot Environment placing definitions. |
| */ |
| #define CONFIG_ENV_SECT_SIZE 0x00010000 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ |
| CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_ENV_SIZE 0x02000 |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + \ |
| CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| |
| /* Miscellaneous configurable options */ |
| #define CONFIG_ARCH_CPU_INIT |
| #define CONFIG_BOOT_PARAMS_ADDR 0x00000100 |
| #define CONFIG_CMDLINE_TAG |
| #define CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_MISC_INIT_R |
| #define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00800000 |
| #define CONFIG_SYS_MEMTEST_END 0x04000000 |
| #define CONFIG_SYS_MALLOC_LEN (8 << 20) |
| #define CONFIG_SYS_LOAD_ADDR 0x00800000 |
| |
| #define CONFIG_HOSTNAME "x600" |
| #define CONFIG_UBI_PART ubi0 |
| #define CONFIG_UBIFS_VOLUME rootfs |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "u-boot_addr=1000000\0" \ |
| "u-boot=" CONFIG_HOSTNAME "/u-boot.spr\0" \ |
| "load=tftp ${u-boot_addr} ${u-boot}\0" \ |
| "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ |
| " +${filesize};" \ |
| "erase " __stringify(CONFIG_SYS_MONITOR_BASE) " +${filesize};" \ |
| "cp.b ${u-boot_addr} " __stringify(CONFIG_SYS_MONITOR_BASE) \ |
| " ${filesize};" \ |
| "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \ |
| " +${filesize}\0" \ |
| "upd=run load update\0" \ |
| "ubifs=" CONFIG_HOSTNAME "/ubifs.img\0" \ |
| "part=" __stringify(CONFIG_UBI_PART) "\0" \ |
| "vol=" __stringify(CONFIG_UBIFS_VOLUME) "\0" \ |
| "load_ubifs=tftp ${kernel_addr} ${ubifs}\0" \ |
| "update_ubifs=ubi part ${part};ubi write ${kernel_addr} ${vol}" \ |
| " ${filesize}\0" \ |
| "upd_ubifs=run load_ubifs update_ubifs\0" \ |
| "init_ubifs=nand erase.part ubi0;ubi part ${part};" \ |
| "ubi create ${vol} 4000000\0" \ |
| "netdev=eth0\0" \ |
| "rootpath=/opt/eldk-4.2/arm\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "boot_part=0\0" \ |
| "altbootcmd=if test $boot_part -eq 0;then " \ |
| "echo Switching to partition 1!;" \ |
| "setenv boot_part 1;" \ |
| "else; " \ |
| "echo Switching to partition 0!;" \ |
| "setenv boot_part 0;" \ |
| "fi;" \ |
| "saveenv;boot\0" \ |
| "ubifsargs=set bootargs ubi.mtd=ubi${boot_part} " \ |
| "root=ubi0:rootfs rootfstype=ubifs\0" \ |
| "kernel=" CONFIG_HOSTNAME "/uImage\0" \ |
| "kernel_fs=/boot/uImage \0" \ |
| "kernel_addr=1000000\0" \ |
| "dtb=" CONFIG_HOSTNAME "/" \ |
| CONFIG_HOSTNAME ".dtb\0" \ |
| "dtb_fs=/boot/" CONFIG_HOSTNAME ".dtb\0" \ |
| "dtb_addr=1800000\0" \ |
| "load_kernel=tftp ${kernel_addr} ${kernel}\0" \ |
| "load_dtb=tftp ${dtb_addr} ${dtb}\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "addcon=setenv bootargs ${bootargs} console=ttyAMA0," \ |
| "${baudrate}\0" \ |
| "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ |
| "net_nfs=run load_dtb load_kernel; " \ |
| "run nfsargs addip addcon addmtd addmisc;" \ |
| "bootm ${kernel_addr} - ${dtb_addr}\0" \ |
| "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ |
| "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ |
| "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip" \ |
| " addcon addmisc addmtd;" \ |
| "bootm ${kernel_addr} - ${dtb_addr}\0" \ |
| "ubifs_mount=ubi part ubi${boot_part};ubifsmount ubi:rootfs\0" \ |
| "ubifs_load=ubifsload ${kernel_addr} ${kernel_fs};" \ |
| "ubifsload ${dtb_addr} ${dtb_fs};\0" \ |
| "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip addcon " \ |
| "addmtd addmisc;bootm ${kernel_addr} - ${dtb_addr}\0" \ |
| "bootcmd=run nand_ubifs\0" \ |
| "\0" |
| |
| /* Physical Memory Map */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define PHYS_SDRAM_1 0x00000000 |
| #define PHYS_SDRAM_1_MAXSIZE 0x40000000 |
| |
| #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 |
| #define CONFIG_SRAM_BASE 0xd2800000 |
| /* Preserve the last 2 lwords for the boot-counter */ |
| #define CONFIG_SRAM_SIZE ((8 << 10) - 0x8) |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SRAM_BASE |
| #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SRAM_SIZE |
| |
| #define CONFIG_SYS_INIT_SP_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| #define CONFIG_SYS_INIT_SP_ADDR \ |
| (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) |
| |
| /* |
| * SPL related defines |
| */ |
| #define CONFIG_SPL_TEXT_BASE 0xd2800b00 |
| #define CONFIG_SPL_MAX_SIZE (CONFIG_SRAM_SIZE - 0xb00) |
| #define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/spear" |
| |
| /* |
| * Please select/define only one of the following |
| * Each definition corresponds to a supported DDR chip. |
| * DDR configuration is based on the following selection |
| */ |
| #define CONFIG_DDR_MT47H64M16 1 |
| #define CONFIG_DDR_MT47H32M16 0 |
| #define CONFIG_DDR_MT47H128M8 0 |
| |
| /* |
| * Synchronous/Asynchronous operation of DDR |
| * |
| * Select CONFIG_DDR_2HCLK for DDR clk = 333MHz, synchronous operation |
| * Select CONFIG_DDR_HCLK for DDR clk = 166MHz, synchronous operation |
| * Select CONFIG_DDR_PLL2 for DDR clk = PLL2, asynchronous operation |
| */ |
| #define CONFIG_DDR_2HCLK 1 |
| #define CONFIG_DDR_HCLK 0 |
| #define CONFIG_DDR_PLL2 0 |
| |
| /* |
| * xxx_BOOT_SUPPORTED macro defines whether a booting type is supported |
| * or not. Modify/Add to only these macros to define new boot types |
| */ |
| #define USB_BOOT_SUPPORTED 0 |
| #define PCIE_BOOT_SUPPORTED 0 |
| #define SNOR_BOOT_SUPPORTED 1 |
| #define NAND_BOOT_SUPPORTED 1 |
| #define PNOR_BOOT_SUPPORTED 0 |
| #define TFTP_BOOT_SUPPORTED 0 |
| #define UART_BOOT_SUPPORTED 0 |
| #define SPI_BOOT_SUPPORTED 0 |
| #define I2C_BOOT_SUPPORTED 0 |
| #define MMC_BOOT_SUPPORTED 0 |
| |
| #endif /* __CONFIG_H */ |